M2XRP2-B40-R/CE [MSYSTEM]
Super-mini Signal Conditioners Mini-M Series;![M2XRP2-B40-R/CE](http://pdffile.icpdf.com/pdf2/p00353/img/icpdf/M2XRP2-B10-R_2172717_icpdf.jpg)
型号: | M2XRP2-B40-R/CE |
厂家: | ![]() |
描述: | Super-mini Signal Conditioners Mini-M Series |
文件: | 总6页 (文件大小:141K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MODEL: M2XRP2
Super-mini Signal Conditioners Mini-M Series
[1] INPUT
0: User-calibrated (Factory default: open collector, 0 – 100 kHz)
ENCODER SPEED TRANSMITTER
(PC programmable; built-in excitation)
Functions & Features
If the unit is to be factory-calibrated to a specific
input type, please select from the following:
A: Open collector
• Converts a two-phase forward and reverse rotation
pulse signal with 90 degree phase difference into a forward
and reverse speed signal
B: Voltage pulse
J: RS-422 line driver pulse
• Built-in excitation
• PC programmable input and output ranges
• Input pulse monitoring LED
[2] EXCITATION
0: User-calibrated (Factory default: 12 V DC / 5 mA)
• Direct RS-422 input
If the unit is to be factory-calibrated to a specific
voltage value, please select from the following:
1: 5 V DC / 5 mA
Typical Applications
• Measuring moving speed of a machine with a rotary
encoder
4: 12 V DC / 5 mA
[3] OUTPUT
29.5 (1.16)
0: User-calibrated (Factory default: 4 – 20 mA)
M
od
el
If the unit is to be factory-calibrated to a specific
output type, please select from the following:
Current
76
(2.99)
Z1: Range 0 – 20 mA DC
124
(4.88)
Voltage
V1: Range -2.5 – +2.5 V DC
mm (inch)
V2: Range -10 – +10 V DC
(Configurator software is used to change output over the
described range of the selected suffix code. For changing
out of this range, set the Output Range Selectors inside the
unit before software adjustment.)
MODEL: M2XRP2-[1][2][3]-[4][5]
ORDERING INFORMATION
• Code number: M2XRP2-[1][2][3]-[4][5]
[4] POWER INPUT
AC Power
Specify a code from below for each [1] through [5].
(e.g. M2XRP2-000-M2/CE/Q)
M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,
• Specify the specification for option code /Q
(e.g. /C01/S01)
47 – 66 Hz)
(90 – 264 V for UL)
• Non-specified orders will be shipped at default factory
settings (M2XRP2-000: Open collector input/12 V
excitation/4 – 20 mA output). However, a power suffix code
must be specified.
DC Power
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
P: 110 V DC
If you specify a full code number without specific calibration
ranges, the input frequency is factory set to the maximum
range available for the selected input code and the output is
set to the default range. Use Ordering Information Sheet
(No. ESU-5059).
(Operational voltage range 85 – 150 V, ripple 10 %p-p max.)
(110 V ±10 % for UL)
Note: Must be used with its socket. NOT installable to a
multi-unit installation base. (e.g. model: M2BS-16)
http://www.m-system.co.jp/
M2XRP2 SPECIFICATIONS
ES-5059 Rev.12 Page 1/6
MODEL: M2XRP2
RS-232-C level
[5] OPTIONS (multiple selections)
Standards & Approvals (must be specified)
/N: Without CE or UL
Pulse sensing: DC coupled or capacitor coupled selectable
with DIP SW
Low-end cutout: 100 msec. – 100 sec. or no cutout
programmable
/CE: CE marking
/UL: UL approval, CE marking
Other Options
blank: none
INPUT SPECIFICATIONS
Excitation: Shortcircuit protection; 20 mA max. at
shortcircuit
/Q: Option other than the above (specify the specification)
Maximum frequency: 200 kHz
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
Frequency ranges:
0 – 10 mHz, 0 – 100 mHz, 0 – 1 Hz, 0 – 10 Hz, 0 – 100 Hz,
0 – 1 kHz, 0 – 10 kHz, 0 – 100 kHz
(Choose 100 kHz range to set the zero/span frequencies
lower than -100 kHz (higher than 100 kHz in the reverse
direction) or higher than 100 kHz (higher than 100 kHz in
the forward direction.))
/C02: Polyurethane coating
/C03: Rubber coating (UL not available)
TERMINAL SCREW MATERIAL
/S01: Stainless steel (UL not available)
Minimum pulse width time requirement: 2.5 μsec.
Minimum span: 10 % of the selected frequency range
Noise filter: See table 2
RELATED PRODUCTS
• PC configurator software (model: JXCON)
Downloadable at M-System’s web site.
A dedicated cable is required to connect the module to the
PC. Please refer to the internet software download site or
the users manual for the PC configurator for applicable
cable types.
■ Open Collector
Input requirements
EXCITATION
5 V
SENSING
OFF
ON
Approx. 5 V
Approx. 10 V
≥200 kΩ
≥200 kΩ
≤200 Ω
≤200 Ω
12 V
Amplitude: 5 - 12 V
Detecting level:
GENERAL SPECIFICATIONS
Construction: Plug-in
5 V excitation: 1 V
12 V excitation: 2 V
Connection: M3 screw terminals (torque 0.8 N·m)
Screw terminal: Chromated steel (standard) or stainless
steel
(Detecting voltage in the internal circuit.
For open collector input, be sure to re-adjust the voltage
back to 1 V (5 V excitation) or 2 V (12 V excitation) if it has
been changed for other input types.)
Detecting pulse edge: OFF to ON
Housing material: Flame-resistant resin (black)
Isolation: Input to output to power
Overrange output: Approx. -15 to +115 % at 1 – 5 V
Zero adjustment: -5 to +5 % (front)
Span adjustment: 95 to 105 % (front)
Configuration: Via PC Configurator Software (model:JXCON)
on the Windows PC connected to
the front jack.
If not specified, the input range is 0 Hz – 1 kHz.
■ Voltage Pulse
Waveform: Square or sine
Input impedance: 10 kΩ min.
Pulse amplitude: 0.1 – 30 Vp-p
Pulse amplitude Range: See table 1.
Max. voltage between input terminals: See table 1.
Sensitivity Scale: See table 1.
Programmable features include:
· I/O type and range
· Zero and span adjustments
Detecting level: -2 – +4 V
· Low-end cutout
Detecting pulse state: A pulse rise detected when the input
voltage goes above the detecting level;
a pulse sink detected when it goes below the level.
If not specified, the input range is 0 Hz – 1 kHz.
■ RS-422 Line Driver Pulse
· Linearization
Status indicator LED: Red LED; Flashing patterns indicate
different operating status of the transmitter.
Input monitor (PL1): Green LED blinks according to the input
phase A.
Receiver: Conforms to RS-422
Input monitor (PL2): Green LED blinks according to the input
phase B.
If not specified, the input range is 0 Hz – 1 kHz.
Excitation adjustment: 5V or 12V DC
Configurator connection: 2.5 dia. miniature jack;
http://www.m-system.co.jp/
M2XRP2 SPECIFICATIONS
ES-5059 Rev.12 Page 2/6
MODEL: M2XRP2
[Table 1]
If not specified, the output range is shown below.
SENSITIVITY
SCALE
MAX.INPUT
VOLTAGE
PULSE AMPLITUDE
RANGE
V1: 0 – 1 V DC
V2: 1 – 5 V DC
10 – 30 Vp-p
5 – 10 Vp-p
1 – 5 Vp-p
30 V
10 V
5 V
1/6
1/2
1
INSTALLATION
Power Consumption
0.1 – 1 Vp-p*
1 V
5
*Input frequency within 50 kHz
•AC:
When the parameters have been set with DIP switches and the
PC Configurator Software (model: JXCON), a specific sensitivity
scale is applied according to the pulse amplitude setting. The
scaled input voltage is then compared to the preset detecting
level (-2.00 to +4.00 V).
Approx. 4 VA at 100 V
Approx. 5 VA at 200 V
Approx. 6 VA at 264 V
With DC coupling, the scaled maximum voltage must be higher
than the detecting level and the minimum voltage must be lower
than that so that the pulse state is accurately detected. (Refer to
the instruction manual for detailed information about adjusting the
detecting level.)
•DC: Approx. 3 W
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Surface or DIN rail
Weight: 150 g (0.33 lb)
[Table 2]
FREQUENCY RANGE
0 – 10 mHz
0 – 100 mHz
0 – 1 Hz
NOISE FILTER TYPE
With
With
With
W/O
W/O
W/O
W/O
W/O
PERFORMANCE
Accuracy: Input accuracy + output accuracy
Input accuracy: ≤ ±0.03% of the selected freq. range
Output accuracy: ≤ ±0.03% of the selected output range
The input accuracy is inversely proportional to the input
span; while the output accuracy is likewise inversely
proportional to the output span. With [Input Range / Input
Span] ≤ 1, the input accuracy is fixed at ±0.03%.
See CALCULATION EXAMPLES OF OVERALL ACCURACY.
Temp. coefficient: ±0.015 %/°C (±0.008 %/°F) of I/O range
at -5 to +55°C [23 to 131°F]
0 – 10 Hz
0 – 100 Hz
0 – 1 kHz
0 – 10 kHz
0 – 100 kHz
Be sure to apply the noise filter appropriate for the selected
frequency range as shown in the table above. The accuracy
may not be assured if no filter is applied.
OUTPUT SPECIFICATIONS
■ DC Current
Response time: 0.5 sec. + 1 pulse cycle (0 – 90 %)
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (input to output
to power to ground)
Output range: 0 – 20 mA DC
Conformance range: 0 – 23mA DC
Minimum span: 1 mA
Offset: Lower range can be any specific value within the
output range provided that the minimum span is
maintained.
CALCULATION EXAMPLES OF OVERALL ACCURACY
[Example] Open collector input, 0 – 50 kHz; 1 – 5 V output.
Selected freq. range (100 kHz) ÷ Input span (50 kHz)×
Accuracy (0.03 %)= 0.06 % (Input accuracy)
Load resistance: Output drive 12 V max.
(e.g. 4 – 20 mA: 600 Ω [12 V ÷ 20 mA])
If not specified, the output range is 4 – 20 mA DC.
■ DC Voltage
Selected output range (20 V) ÷ Output span (4 V) ×
Accuracy (0.03 %)= 0.15 % (Output accuracy)
Code V1 (narrow spans)
Conformance range: -3 – +3 V DC
Output range: -2.5 – +2.5 V DC
Minimum span: 250 mV
Overall accuracy = 0.06 + 0.15 = ±0.21 %
Code V2 (wide spans)
Conformance range: -11.5 – +11.5 V DC
Output range: -10 – +10 V DC
Minimum span: 1 V
Offset: Lower range can be any specific value within the
output range provided that the minimum span is
maintained.
Load resistance: Output drive 1 mA max.
(e.g. 1 – 5 V: 5000 Ω [5 V ÷ 1 mA])
http://www.m-system.co.jp/
M2XRP2 SPECIFICATIONS
ES-5059 Rev.12 Page 3/6
MODEL: M2XRP2
STANDARDS & APPROVALS
EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
Low Voltage Directive
EN 61010-1
Installation Category II
Pollution Degree 2
Input or output to power: Reinforced insulation (300 V)
Input to output: Basic insulation (300 V)
RoHS Directive
EN 50581
Approval:
UL/C-UL nonincendive Class I, Division 2,
Groups A, B, C, and D
(ANSI/ISA-12.12.01, CAN/CSA-C22.2 No.213)
UL/C-UL general safety requirements
(UL 61010-1, CAN/CSA-C22.2 No.61010-1)
EXTERNAL VIEW
Input Selector SW
■ FRONT VIEW (with cover open)
■ LEFT SIDE VIEW (with cover removed)
4
3
2
1
Configurator Jack
ON OFF ON OFF
OFF
ON
1
2
1
2
Input Monitor LED, PL1
SW1
SW2
SW3
Input Monitor LED, PL2
Status Indicator LED
Zero/Span Selector
Top: SPAN
Middle: OFF
Bottom: ZERO
Output Selector SW
ON OFF
UP/DOWN Switches
4
3
2
1
The front cover cannot be opened to 180 deg.
when flush with neighboring units.
SW4
Refer to the instruction manual for detailed procedures.
http://www.m-system.co.jp/
M2XRP2 SPECIFICATIONS
ES-5059 Rev.12 Page 4/6
MODEL: M2XRP2
OPERATION
20mA
+10V
4mA
rev. 30 Hz
–10V
fwd. 100 Hz
CUTOUT
rev. 100 Hz
fwd. 100 Hz
REVERSE
STOP
FORWARD
φ
φ
A
B
INPUT
INPUT
+
ACCEL.
DECEL.
0 Hz
ACCEL.
CUTOUT
–
Forward Rotation: Phase A leads the Phase B by 90 degrees.
Reverse Rotation: Phase A lags behind Phase B by 90 degrees.
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
6 (.23)
DIN RAIL
35mm wide
3
2
5
1
4
6
2–4.2x5
(.17x.20)
MTG HOLE
6 (.24) deep
9
8
7
11–M3
SCREW
11 10
21.5 (.85) 7.3 (.29)
86.7 (3.41)
116.7 (4.59)
22 (.87)
[4 (.16)]
29.5 (1.16)
• When mounting, no extra space is needed between units.
http://www.m-system.co.jp/
M2XRP2 SPECIFICATIONS
ES-5059 Rev.12 Page 5/6
MODEL: M2XRP2
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
■ OPEN COLLECTOR, VOLTAGE INPUT
INPUT
MON. PL1
STATUS
MON.
3
6
ZERO/SPAN
SELECTOR
INPUT TYPE
SELECTOR
ROTARY
ENCODER
Isolation
Waveform
Shaper
Digital
Computation
Output
Driver
+
–
+
+
1
7
8
+
φ
A
OUTPUT
POWER
2
–
COM
UP/DOWN
SWITCHES
Waveform
Shaper
5
10
11
9
U(+)
V(–)
φ
B
Exc.
Supply
4
PWR
INPUT
MON. PL2
JACK
CONFIGURATOR
Base Socket
Remark: The sensor excitation voltage is supplied also across the terminals 3 – 6.
■ RS-422 LINE DRIVER INPUT
STATUS MON.
ROTARY
ENCODER
ZERO/SPAN
SELECTOR
–
+
–
+
–
+
6
COM
INPUT
MON. PL1
9
7
Isolation
1
φ
φ
φ
φ
A
A
B
B
RS-422
Receiver
Digital
Computation
Output
Driver
INPUT
MON. PL2
+
2
OUTPUT
POWER
8
–
4
RS-422
Receiver
UP/DOWN
SWITCHES
10
11
U(+)
V(–)
5
Excitation
Supply
3
PWR
JACK
CONFIGURATOR
Base Socket
Specifications are subject to change without notice.
http://www.m-system.co.jp/
M2XRP2 SPECIFICATIONS
ES-5059 Rev.12 Page 6/6
相关型号:
©2020 ICPDF网 联系我们和版权申明