M2XF2-Z1V2-R [MSYSTEM]
Super-mini Signal Conditioners Mini-M Series;型号: | M2XF2-Z1V2-R |
厂家: | M-SYSTEM |
描述: | Super-mini Signal Conditioners Mini-M Series |
文件: | 总5页 (文件大小:121K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MODEL: M2XF2
Super-mini Signal Conditioners Mini-M Series
[2] OUTPUT
Current
Z1: Range 0 – 20 mA DC
Voltage
LINEARIZER
(PC programmable)
V1: Range -2.5 – +2.5 V DC
V2: Range -10 – +10 V DC
Functions & Features
• Accepting non-linear input and providing a linearized
output, proportional to the process variables
• 100-point calibration
(Configurator software is used to change output over the
described range of the selected suffix code. For changing
out of this range, set the Output Range Selectors inside the
unit before software adjustment.)
• PC programmable
Typical Applications
• V-notch weir
[3] POWER INPUT
• Gas analyzer
AC Power
• Irregular-shaped tank level input for volume calculation
• Square root extracting for DP transmitter
M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,
47 – 66 Hz)
(90 – 264 V for UL)
DC Power
23 (.91)
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
P: 110 V DC
M
od
el
76
(2.99)
(Operational voltage range 85 – 150 V, ripple 10 %p-p max.)
(110 V ±10 % for UL)
124
(4.88)
[4] OPTIONS (multiple selections)
Standards & Approvals (must be specified)
/N: Without CE or UL
mm (inch)
/CE: CE marking
/UL: UL approval, CE marking
Other Options
MODEL: M2XF2–[1][2]–[3][4]
blank: none
/Q: Option other than the above (specify the specification)
ORDERING INFORMATION
• Code number: M2XF2-[1][2]-[3][4]
Specify a code from below for each [1] through [4].
(e.g. M2XF2-S2Z1-R/CE/Q)
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
• Input range (e.g. 1 – 5 V DC)
• Output range (e.g. 4 – 20 mA DC)
• Specify the specification for option code /Q
(e.g. /C01/S01/SET)
/C02: Polyurethane coating
/C03: Rubber coating (UL not available)
TERMINAL SCREW MATERIAL
/S01: Stainless steel (UL not available)
EX-FACTORY SETTING
[1] INPUT
/SET: Preset according to the Ordering Information Sheet
(No. ESU-5085)
Current
Z1: Range 0 – 50 mA DC (Input resistance 100 Ω)
Voltage
S1: Range -1 – +1 V DC (Input resistance 1 MΩ min.)
S2: Range -10 – +10 V DC (Input resistance 1 MΩ min.)
(Configurator software is used to change input over the
described range of the selected suffix code. For changing
out of this range (between S1 and S2), set the Input Range
Selector on the side of unit before software adjustment.
For a current input, set the Selector to the same setting as
for S2 and use a receiving resistor.)
RELATED PRODUCTS
• PC configurator software (model: JXCON)
Downloadable at M-System’s web site.
A dedicated cable is required to connect the module to the
PC. Please refer to the internet software download site or
the users manual for the PC configurator for applicable
cable types.
M2XF2 SPECIFICATIONS
ES-5085 Rev.12 Page 1/5
http://www.m-system.co.jp/
MODEL: M2XF2
GENERAL SPECIFICATIONS
Construction: Plug-in
OUTPUT SPECIFICATIONS
■ DC Current
Connection: M3 screw terminals (torque 0.8 N·m)
Screw terminal: Chromated steel (standard) or stainless
steel
Operational range: 0 – 24 mA DC
Output range: 0 – 20 mA DC
Minimum span: 1 mA
Housing material: Flame-resistant resin (black)
Isolation: Input to output to power
Overrange output: Approx. -15 to +115 %
(Negative current output is not provided.)
Manual zero adjustments: -5 to +5 %
(factory setting: 0 %)
Offset: Lower range can be any specific value within the
output range provided that the minimum span is
maintained.
Load resistance: Output drive 15 V max.
(e.g. 4 – 20 mA: 750 Ω [15 V ÷ 20 mA])
If not specified, the output range is 4 – 20 mA DC.
■ DC Voltage
Manual span adjustments: 95 to 105 %
(factory setting: 100 %)
Code V1 (narrow spans)
Programming: Downloaded from PC; input range, output
range, zero and span, linearization table, simulating output,
etc.
Operational range: -3 – +3 V DC
Output range: -2.5 – +2.5 V DC
Minimum span: 250 mV
Linearization: 100 points max. within the range of
-15 – +115 % input or output; represented as percentage of
full-scale
Code V2 (wide spans)
Operational range: -11.5 – +11.5 V DC
Output range: -10 – +10 V DC
Minimum span: 1 V
Status indicator LED: Blinking patterns indicate different
operating status of the transmitter.
Configurator connection: 2.5 dia. miniature jack;
RS-232-C level
Offset: Lower range can be any specific value within the
output range provided that the minimum span is
maintained.
Load resistance: Output drive 1 mA max.
(e.g. 1 – 5 V: 5000 Ω [5 V ÷ 1 mA])
If not specified, the output range is shown below.
V1: 0 – 1 V DC
INPUT SPECIFICATIONS
■ DC Current: Shunt resistor attached to the input terminals
(0.5 W)
V2: 1 – 5 V DC
Operational range: 0 – 70 mA DC with 100 Ω, 0.5 W
Input range: 0 – 50 mA DC
Minimum span: 2 mA
INSTALLATION
Offset: Lower range can be any specific value within the
input range provided that the minimum span is maintained.
If not specified, the input range is 4 – 20 mA DC.
■ DC Voltage
Power Consumption
•AC:
Approx. 3 VA at 100 V
Approx. 4 VA at 200 V
Code S1 (narrow spans)
Approx. 5 VA at 264 V
Operational range: -1.15 – +1.15 V DC
Input range: -1 – +1 V DC
•DC: Approx. 2 W
Operating temperature: -30 to +60°C (-22 to +140°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Surface or DIN rail
Weight: 120 g (0.26 lb)
Minimum span: 10 mV
Code S2 (wide spans)
Operational range: -11.5 – +11.5 V DC
Input range: -10 – +10 V DC
Minimum span: 100 mV
Offset: Lower range can be any specific value within the
input range provided that the minimum span is maintained.
If not specified, the input range is shown below.
S1: 0 – 100 mV DC
S2: 1 – 5 V DC
M2XF2 SPECIFICATIONS
ES-5085 Rev.12 Page 2/5
http://www.m-system.co.jp/
MODEL: M2XF2
PERFORMANCE in percentage of span
Overall accuracy:
Input accuracy + output accuracy [gain ≤ 1]
(inp. accuracy + out. accuracy) × gain [gain > 1]
Inversely proportional to the span.
Except the accuracy of input resistor.
See CALCULATION EXAMPLES OF OVERALL ACURACY.
• Input accuracy: (% of max. input range)
-1 – +1 V : ±0.01 %
-10 – +10 V : ±0.01 %
0 – 50 mA : ±0.02 %
• Output accuracy: ±0.04 % of max. output range
Temp. coefficient: ±0.015 %/°C (±0.008 %/°F) of max. span
at -5 to +55°C [23 to 131°F]
Response time: ≤ 0.9 sec. (0 – 90 %)
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (input to output
to power to ground)
CALCULATION EXAMPLES OF OVERALL ACCURACY
[Example] Input Type -10 – +10 V, Input Range 1 – 5 V,
Output Type 0 – 20 mA, Output Range 4 – 20 mA
Max. Input Range (20 V) ÷ Span (4 V) × 0.01 % = 0.05 %
Max. Output Range (20 mA) ÷ Span (16 mA) × 0.04 %
= 0.05 %
Overall accuracy = 0.05 + 0.05 = ±0.10 %
STANDARDS & APPROVALS
EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
Low Voltage Directive
EN 61010-1
Installation Category II
Pollution Degree 2
Input or output to power: Reinforced insulation (300 V)
Input to output: Basic insulation (300 V)
RoHS Directive
EN 50581
Approval:
UL/C-UL nonincendive Class I, Division 2,
Groups A, B, C, and D
(ANSI/ISA-12.12.01, CAN/CSA-C22.2 No.213)
UL/C-UL general safety requirements
(UL 61010-1, CAN/CSA-C22.2 No.61010-1)
M2XF2 SPECIFICATIONS
ES-5085 Rev.12 Page 3/5
http://www.m-system.co.jp/
MODEL: M2XF2
EXTERNAL VIEW
■ FRONT VIEW (with cover open)
■ RIGHT SIDE VIEW
Configurator Jack
Status Indicator LED
Zero/Span Selector
Input Range Selector
Position L : code S1
Position H: code S2, Z1
Top: SPAN
Middle: OFF
Bottom: ZERO
ATT
[e.g.]
Output code V1
V
I
UP/DOWN Switches
SW3
SW6
SW2
The front cover cannot be turned open by 180 deg.
when there is no extra space between units.
8
■ LEFT SIDE VIEW
(with cover removed)
7
6
5
4
3
2
1
V
I
N
O
SW7
SW4
Output Range Selectors
Refer to the instruction manual for detailed procedures.
EXTERNAL DIMENSIONS unit: mm (inch)
6 (.23)
DIN RAIL
35mm wide
4
1
5
8
2–4.2x5
(.17x.20)
MTG HOLE
6 (.24) deep
12
9
8–M3
SCREW
14 13
21.5 (.85) 7.3 (.29)
86.7 (3.41)
116.7 (4.59)
15 (.59)
[4 (.16)]
23 (.91)
• When mounting, no extra space is needed between units.
M2XF2 SPECIFICATIONS
ES-5085 Rev.12 Page 4/5
http://www.m-system.co.jp/
MODEL: M2XF2
TERMINAL ASSIGNMENTS unit: mm (inch)
INPUT RESISTOR
(model: REM2)
4
1
5
8
12
9
14 13
Input shunt resistor attached
for current input.
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
STATUS
INPUT RANGE
SELECTOR
ZERO/SPAN
SELECTOR
OUTPUT RANGE
SELECTORS
Isolation
Digital
Computation
Output
Driver
+
–
1
9
+
Low Drift
Amplifier
*
INPUT
R
OUTPUT
POWER
4
12
13
14
–
UP/DOWN
SWITCHES
5
U(+)
V(–)
8
JACK
CONFIGURATOR
Base Socket
*Input shunt resistor attached for current input.
Specifications are subject to change without notice.
M2XF2 SPECIFICATIONS
ES-5085 Rev.12 Page 5/5
http://www.m-system.co.jp/
相关型号:
©2020 ICPDF网 联系我们和版权申明