KS2V2-61-R [MSYSTEM]

Plug-in Signal Conditioners K-UNIT;


型号：	KS2V2-61-R
厂家：	M-SYSTEM
描述：	Plug-in Signal Conditioners K-UNIT
文件：	总4页 (文件大小：142K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: KS2V2

Plug-in Signal Conditioners K-UNIT

[2] OPTIONS

blank: none

/Q: Options other than the above (specify the specification)

DC INPUT LIMIT ALARM

(digital adjustments; dual alarm trip; burnout)

Functions & Features

SPECIFICATIONS OF OPTION: Q

EX-FACTORY SETTING

• Providing relay contact closures at preset DC input levels

• Dual (Hi/Lo) trip

/SET: Preset according to the Ordering Information Sheet

(No. ESU-3608)

• Front digital displays

• Programmable with front keys

RELATED PRODUCTS

• Resistor module (model: REM)

500 Ω for 2 – 10 mA DC

Typical Applications

• Various alarm applications

250 Ω for 4 – 20 mA DC

50 (1.97)

100 Ω for 10 – 50 mA DC

70 (2.76)

110 (4.33)

mm (inch.)

MODEL: KS2V2–61–[1][2]

ORDERING INFORMATION

• Code number: KS2V2-61-[1][2]

Specify a code from below for each of [1] and [2].

(e.g. KS2V2-61-R/Q)

• Specify the specification for option code /Q

(e.g. /SET)

INPUT

Voltage

6: 1 – 5 V DC

(Use a resistor module for current input)

OUTPUT

1: Relay; SPDT or transfer contact

[1] POWER INPUT

AC Power

M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,

47 – 66 Hz)

DC Power

R: 24 V DC

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

KS2V2 SPECIFICATIONS

ES-3608 Rev.10 Page 1/4

https://www.m-system.co.jp/

MODEL: KS2V2

Measured Value (PV) indicator: Green LED turns on when PV

display is set.

GENERAL SPECIFICATIONS

Construction: Panel flush mounting, plug-in

Connection: M3.5 screw terminals

Alarm SET1 indicator: Red LED turns on when the Alarm

SET1 is in tripped conditions.

Screw terminal: Chromated steel

Alarm SET2 Indicator: Red LED turns on when the Alarm

SET2 is in tripped conditions.

Housing material: Flame-resistant resin (gray)

Isolation: Input to SET1 to SET2 to power

Time constant for the input filter (P-dF): 0.0 to 900.0 sec. (0

– 63 %)

Engineering unit indication: Sticker label attached;

DC, AC, W, °C, °F, V, mV, A, mA, %, kW, mW,

kV, kA, kvar, Mvar, var, m, mm, kg, kg/h,

Alarm relay switching delay time (P-d1, P-d2): 1 to 10 sec.;

programmable independently for each setpoint

Programming: Front key

kPa, MPa, N·m, Nm

/h, m

/h, m /sec, m/sec,

ℓ/min, %RH, ℓ, ℓ/h, t/h, rpm, ppm, pH, Pa.

Setpoint adjustment (ST1, ST2): -5 to +105 %;

programmable independently for each setpoint

Deadband (hysteresis) (HYS1, HYS2): 0 – 102 %;

programmable independently for each setpoint

Burnout: Upscale (standard), downscale (available to

change)

INPUT SPECIFICATIONS

■ DC Voltage: -5 – +105 %

Input resistance: ≥ 1 MΩ

OUTPUT SPECIFICATIONS

■ Relay Contact: SPDT relays

Power ON delay (P-d0): 0 to 20 sec.

Read rate: 0.5 sec.

220 V AC @3 A (cos ø = 1)

Alarm mode (P-A1, P-A2): Programmable independently for

each setpoint; See Table below.

30 V DC @3 A (resistive load)

Caution: N.O. and N.C. contacts could be conductive at the

same time. DO NOT connect both contacts at the same

time.

Param.

Code

Alarm Modes

Latching

Hold*

Trip

Operation

Set Value

Relay & LED

Behavior in

Tripped Conditions

(P-A1)

(P-A2)

Maximum switching voltage: 220 V AC or 30 V DC

Maximum switching power: 660 VA or 90 W

Minimum load: 10 V DC @1 mA

No alarm

High

----

Absolute value

Without

LED ON

Coil energized

Low

High

Low

High

Low

High

Low

Absolute value

Without

With

LED ON

Coil energized

Mechanical life: 2 × 10 cycles with no loads

For maximum relay life with inductive loads, external

protection is recommended.

LED ON

Coil energized

With

LED ON

Coil energized

Without

With

LED ON

Coil de-energized

INSTALLATION

Power consumption

LED ON

Coil de-energized

•AC:

LED ON

Coil de-energized

Approx. 3.1 VA at 100 V

Approx. 4.1 VA at 200 V

With

LED ON

Coil de-energized

Approx. 4.8 VA at 264 V

*Without latching hold function, the unit is tripped upon starting operation when

the unit is set to Low alarm.

•DC: Approx. 1.7 W

With the function, the unit is NOT tripped until the temperature goes once above

and then below the setpoint.

Operating temperature: -10 to +55°C (14 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Panel flush mounting with attached

mounting bracket, surface or DIN rail

Weight: 200 g (0.44 lb)

DISPLAY

Display: 4 digits of 10 mm (.39”) height, 7-segment LED

Scaling range: -1999 to 9999 counts

Measured Value (PV)/Alarm (SET1) display: Red LEDs

Alarm (SET2) parameter display: Green LEDs

PV display at abnormal input: Over range or under range

displayed

PERFORMANCE

Display accuracy: ±0.5% FS ±1 digit

Setpoint accuracy: Display accuracy ± 0.1 % FS

Trip point repeatability: Included in the setpoint accuracy

Line voltage effect: Included in the display accuracy

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 1500 V AC @1 minute

Front LEDs

Power indicator: Green LED turns on while the power is

turned on.

KS2V2 SPECIFICATIONS

ES-3608 Rev.10 Page 2/4

https://www.m-system.co.jp/

MODEL: KS2V2

(input to SET1 or SET2 to power)

500 V AC @1 minute (SET1 to SET2)

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

Low Voltage Directive

EN 61010-1

Installation Category II (power)

Measurement Category II (output)

Pollution Degree 2

Input to output to power: Basic insulation (300 V)

RoHS Directive

EXTERNAL VIEW

H. Alarm SET1 Indicator LED

J. Alarm SET2 Indicator LED

G. Power Indicator LED

A. Measured Value (PV) /

Alarm SET1 Display

B. Measured Value (PV)

Indicator LED

C. Alarm SET2 / Parameter Display

D. SELECT Key

F. DOWN Key

E. UP Key

Component Name

Ref.

Function

Measured Value (PV) / Alarm SET1 Display Displaying either of Measured Value (PV) or Alarm Setpoint Value (SET1)

LED turns on when the Measured Value (PV) is displayed.

Measured Value (PV) Indicator LED

Alarm SET2 / Parameter Display

SELECT Key

Displaying either of Alarm Setpoint Value (SET2) or parameter type code.

Used for confirming current setpoints and switching between parameter blocks.

Pressing the key increases display values.

UP Key

They change continuously when it is kept pressed.

Pressing the key decreases display values.

DOWN Key

They change continuously when it is kept pressed.

LED turns on while the power is turned on.

Power Indicator LED

Alarm SET1 Indicator LED

Alarm SET2 Indicator LED

LED turns on when the Alarm SET1 is in tripped conditions.

LED turns on when the Alarm SET2 is in tripped conditions.

KS2V2 SPECIFICATIONS

ES-3608 Rev.10 Page 3/4

https://www.m-system.co.jp/

MODEL: KS2V2

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm [inch]

CLAMP

110 (4.33)

(top & bottom)

7.5

(.3)

71.5 (2.81)

1.5 (.06) PACKING

7.8 (.31)

48 (1.89)

DIN RAIL

35mm wide

2–4.5 (.18) dia.

MTG HOLE

25 (.98) deep

10 11

MOUNTING

BRACKET

1 1–M3.5

SCREW

PANEL

[3.5] (.14)

40 (1.57)

50 (1.97)

1 ≤ t ≤ 8

(.04 ≤ t ≤.31)

PANEL CUTOUT unit: mm

■PANEL CUTOUT

+0.5

45 ⁰

63 MIN.

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

11 N.C.

10 N.O. SET1

–

INPUT

A/D

Converter

COM

Digital

Computation

N.C.

N.O. SET2

COM

Display/

Setting

U(+)

POWER

V(–)

Base Socket

Specifications are subject to change without notice.

KS2V2 SPECIFICATIONS

ES-3608 Rev.10 Page 4/4

https://www.m-system.co.jp/

KS2V2-61-R [MSYSTEM]

相关型号：

KS2V2-61-R/Q

KS2V3

KS2V3-61-M2

KS2V3-61-M2/Q

KS2V3-61-R

KS2V3-61-R/Q

KS300

KS3004JTE10N

KS3004KTE10N

KS3004LBK10NJ

KS3004LBK10NK

KS3004LTE10NJ