KPK-16-R/Q 概述
Plug-in Signal Conditioners K-UNIT
KPK-16-R/Q 数据手册
通过下载KPK-16-R/Q数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载MODEL: KPK
F: 0 – 10 mA DC (Load resistance 1200 Ω max.)
Plug-in Signal Conditioners K-UNIT
G: 0 – 1 mA DC (Load resistance 12 kΩ max.)
Z: Specify current (See OUTPUT SPECIFICATIONS)
Voltage
PT TRANSMITTER
(approximate RMS sensing)
1: 0 – 10 mV DC (Load resistance 10 kΩ min.)
2: 0 – 100 mV DC (Load resistance 100 kΩ min.)
3: 0 – 1 V DC (Load resistance 100 Ω min.)
4: 0 – 10 V DC (Load resistance 1000 Ω min.)
5: 0 – 5 V DC (Load resistance 500 Ω min.)
6: 1 – 5 V DC (Load resistance 500 Ω min.)
4W: -10 – +10 V DC (Load resistance 2000 Ω min.)
0: Specify voltage (See OUTPUT SPECIFICATIONS)
Functions & Features
• Converting an alternating voltage from a potential
(voltage) transformer into a standard process signal
• Minimum ripple
• Isolation up to 2000 V AC
• High-density mounting
Typical Applications
• Centralized monitoring and control of power line and
power supply voltages measured at switch boards
• Monitoring abnormal voltage drops for detecting overload
[3] AUXILIARY POWER SUPPLY
AC Power
B: 100 V AC
C: 110 V AC
50
(1.97)
D: 115 V AC
F: 120 V AC
G: 200 V AC
80
(3.15)
H: 220 V AC
J: 240 V AC
DC Power
123
(4.84)
R: 24 V DC
mm (inch)
V: 48 V DC
P: 110 V DC
MODEL: KPK–[1][2]–[3][4]
[4] OPTIONS
blank: none
ORDERING INFORMATION
• Code number: KPK-[1][2]-[3][4]
Specify a code from below for each of [1] through [4].
(e.g. KPK-1A-B/Q)
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
• Special output range (For codes Z & 0)
• Specify the specification for option code /Q
(e.g. /C01/S01)
/C02: Polyurethane coating
/C03: Rubber coating
TERMINAL SCREW MATERIAL
/S01: Stainless steel
[1] INPUT
Voltage
1: 0 – 110 V AC
2: 0 – 220 V AC
5: 0 – 150 V AC
6: 0 - 300 V AC
GENERAL SPECIFICATIONS
Construction: Plug-in
Connection: M3.5 screw terminals
Screw terminal: Chromated steel (standard) or stainless
steel
[2] OUTPUT
Current
Housing material: Flame-resistant resin (black)
Isolation: Input to output to auxiliary power
Input waveform: Up to 5 % of 3rd harmonic content
Overrange output: 0 to 120 % at 1 – 5 V
Zero adjustment: -5 to +5 % (front)
Span adjustment: 95 to 105 % (front)
A: 4 – 20 mA DC (Load resistance 600 Ω max.)
B: 2 – 10 mA DC (Load resistance 1200 Ω max.)
C: 1 – 5 mA DC (Load resistance 2400 Ω max.)
D: 0 – 20 mA DC (Load resistance 600 Ω max.)
E: 0 – 16 mA DC (Load resistance 750 Ω max.)
KPK SPECIFICATIONS
ES-3546 Rev.1 Page 1/3
http://www.m-system.co.jp/
MODEL: KPK
INPUT SPECIFICATIONS
Frequency: 50 or 60 Hz
Input burden: 1 VA
Overload capacity: 150 % of rating for 10 sec., 120 %
continuous
Operational range: 0 – 120 % of rating
OUTPUT SPECIFICATIONS
■ DC Current: 0 – 20 mA DC
Minimum span: 1 mA
Offset: Max. 1.5 times span
Load resistance: Output drive 12 V max.
■ DC Voltage: -10 – +12 V DC
Minimum span: 5 mV
Offset: Max. 1.5 times span
Load resistance: Output drive 10 mA max.; 5 mA for
negative voltage output; at ≥ 0.5 V
■OPERATION DIAGRAM (example)
OUT
20mA
OUT
10V
12
4
5
0
0
150
300V
IN
0
150
300V
IN
INSTALLATION
Auxiliary power supply
•AC: Operational voltage range: rating -15/+10 %,
50/60 Hz, approx. 2 VA
•DC: Operational voltage range: rating ±10 %,
or 85 – 150 V for 110 V rating, ripple 10 %p-p max.,
approx. 2 W (18 mA at 110 V)
Operating temperature: -10 to +55°C (14 to 131°F)
Operating humidity: 30 to 85 %RH (non-condensing)
Mounting: Surface or DIN rail
Weight: 350 g (0.77 lb)
PERFORMANCE in percentage of span
Accuracy: ±0.2 % (at 23°C ±10°C or 73.4°F ±18°F, 45 – 65
Hz)
Response time: ≤ 1 sec. (0 – 100 % ±1 %)
Ripple: 0.5 %p-p max.
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute
(input to output to auxiliary power to ground)
Impulse withstand voltage: 1.2 / 50 μsec., ±5 kV
(input to output or ground)
KPK SPECIFICATIONS
ES-3546 Rev.1 Page 2/3
http://www.m-system.co.jp/
MODEL: KPK
CONNECTION DIAGRAM
SOURCE
VT
FUSE
U
V
u
v
3
4
1
2
7
8
+
OUTPUT
–
U(+)
V(–)
LOAD
AUXILIARY POWER*
*
The transmitter can be powered from the input voltage when the voltage
is sufficiently stable and meets within the range of auxiliary power supply
of the unit specified in the data sheet/instruction manual.
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
CLAMP
(top & bottom)
7.8 (.31)
DIN RAIL
35mm wide
6
5
4
3
2–
4.5 (.18) dia.
MTG HOLE
15 (.59) deep
7
8
1
2
8–
M3.5
SCREW
50 (1.97)
103 (4.06)
123 (4.84)
40 (1.57)
50 (1.97)
[3.3 (.13)]
• When mounting, no extra space is needed between units.
Specifications are subject to change without notice.
KPK SPECIFICATIONS
ES-3546 Rev.1 Page 3/3
http://www.m-system.co.jp/
KPK-16-R/Q 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
KPK-16-V | MSYSTEM | Plug-in Signal Conditioners K-UNIT | 获取价格 | |
KPK-16-V/Q | MSYSTEM | Plug-in Signal Conditioners K-UNIT | 获取价格 | |
KPK-1A-B | MSYSTEM | Plug-in Signal Conditioners K-UNIT | 获取价格 | |
KPK-1A-B/Q | MSYSTEM | Plug-in Signal Conditioners K-UNIT | 获取价格 | |
KPK-1A-C | MSYSTEM | Plug-in Signal Conditioners K-UNIT | 获取价格 | |
KPK-1A-C/Q | MSYSTEM | Plug-in Signal Conditioners K-UNIT | 获取价格 | |
KPK-1A-D | MSYSTEM | Plug-in Signal Conditioners K-UNIT | 获取价格 | |
KPK-1A-D/Q | MSYSTEM | Plug-in Signal Conditioners K-UNIT | 获取价格 | |
KPK-1A-F | MSYSTEM | Plug-in Signal Conditioners K-UNIT | 获取价格 | |
KPK-1A-F/Q | MSYSTEM | Plug-in Signal Conditioners K-UNIT | 获取价格 |
KPK-16-R/Q 相关文章
- 2024-09-20
- 5
- 2024-09-20
- 9
- 2024-09-20
- 8
- 2024-09-20
- 6