F2AP-A1-R [MSYSTEM]
Super-mini Signal Conditioners F2 Series;型号: | F2AP-A1-R |
厂家: | M-SYSTEM |
描述: | Super-mini Signal Conditioners F2 Series |
文件: | 总3页 (文件大小:108K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MODEL: F2AP
Super-mini Signal Conditioners F2 Series
[2] OUTPUT
1: Open collector (max. 1 kHz)
2: 5 V pulse (max. 1 kHz)
DC/FREQUENCY CONVERTER
Functions & Features
• Providing a pulse rate output in proportion to DC input
signal
POWER INPUT
DC Power
• High-density mounting
R: 24 V DC
Typical Applications
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
• Totalizing applications in combination with a counter
[3] OPTIONS
blank: none
22.5 (.89)
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
75
(2.95)
/C02: Polyurethane coating
107
(4.21)
mm (inch)
GENERAL SPECIFICATIONS
Construction: Stand-alone; terminal access at the front
Connection: Euro type connector terminal
MODEL: F2AP–[1][2]–R[3]
(applicable wire size: 0.2 to 2.5 mm , stripped length 7 mm)
2
Housing material: Flame-resistant resin (black)
Isolation: Input to output to power
ORDERING INFORMATION
• Code number: F2AP-[1][2]-R[3]
Specify a code from below for each [1] through [3].
(e.g. F2AP-61-R/Q)
Zero adjustment: 0 – 5 % (front)
Span adjustment: 95 to 105 % (front)
• Special input range (For codes Z & 0)
• Output frequency range (e.g. 0 – 500 Hz)
• Specify the specification for option code /Q
(e.g. /C01)
INPUT SPECIFICATIONS
■ DC Current: Input resistor incorporated
Specify input resistance value for code Z.
(R ≤ 0.5 W ÷ [F.S. Current]
■ DC Voltage: 0 – 30 V DC
Minimum span: 1 V
2)
[1] INPUT
Current
Input resistance: ≥ 1 MΩ
A: 4 – 20 mA DC (Input resistance 250 Ω)
D: 0 – 20 mA DC (Input resistance 50 Ω)
G: 0 – 1 mA DC (Input resistance 1000 Ω)
H: 10 – 50 mA DC (Input resistance 100 Ω)
Z: Specify current (See INPUT SPECIFICATIONS)
( 0 % input must be 0 mA.)
OUTPUT SPECIFICATIONS
■ Open Collector: 30 V DC @100 mA (resistive load)
Frequency range: 0 – 10 pulses/hour through 1 kHz
Saturation voltage: 0.6 V DC
■ 5 V Pulse
Voltage
Frequency range: 0 – 10 pulses/hour through 1 kHz
Hi level: 3.0 – 5.5 V
3: 0 – 1 V DC (Input resistance 1 MΩ min.)
4: 0 – 10 V DC (Input resistance 1 MΩ min.)
5: 0 – 5 V DC (Input resistance 1 MΩ min.)
6: 1 – 5 V DC (Input resistance 1 MΩ min.)
0: Specify voltage (See INPUT SPECIFICATIONS)
( 0 % input must be 0 V.)
Lo level: ≤ 0.5 V
Load resistance: 250 Ω min.
F2AP SPECIFICATIONS
ES-5436 Rev.6 Page 1/3
http://www.m-system.co.jp/
MODEL: F2AP
OUTPUT PULSE WIDTH
■ Frequency less than 500 Hz at 100% input
➞ Duty ratio 20% (See the figure below)
• Open Collector
• Voltage Pulse
OFF
H Level
ON
L Level
20
%
20%
80%
80%
1 / f
1 / f
■ Frequency greater than 500 Hz at 100% input
➞ See the figure and equation below.
• Open Collector
• Voltage Pulse
OFF
H Level
ON
L Level
Pulse Width
Pulse Width
1
Pulse Width [millisec.] =
2.09 x 100% Frequency [kHz]
INSTALLATION
Current consumption
•DC: Approx. 80 mA
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: DIN rail
Weight: 150 g (0.33 lb)
PERFORMANCE in percentage of span
Accuracy: ±0.1 %
Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (input to output
to power to ground)
STANDARDS & APPROVALS
EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
RoHS Directive
EN 50581
Approval:
UL/C-UL general safety requirements
(UL 3111-1, CAN/CSA-C22.2 No.1010-1)
F2AP SPECIFICATIONS
ES-5436 Rev.6 Page 2/3
http://www.m-system.co.jp/
MODEL: F2AP
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
DIN RAIL
35mm wide
1
2 3 4
5
6 7 8
22.5 (.89)
107 (4.21)
[1.5 (.06)]
• When mounting, no extra space is needed between units.
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
Z
S
Isolation
Low Drift
Amplifier
Volt. / Freq.
Converter
Output
Driver
+
–
1
2
3
4
5
6
7
8
+
–
+
–
Divider
*
INPUT
OUTPUT
POWER
*Input shunt resistor incorporated for current input.
Output Connection Examples
¢
¢
Voltage Pulse
Open Collector
5
6
+
–
+
–
5
6
+
–
+
–
Specifications are subject to change without notice.
F2AP SPECIFICATIONS
ES-5436 Rev.6 Page 3/3
http://www.m-system.co.jp/
相关型号:
©2020 ICPDF网 联系我们和版权申明