DLA1-1C2-S/Q [MSYSTEM]
Multiplex Transmission System;型号: | DLA1-1C2-S/Q |
厂家: | M-SYSTEM |
描述: | Multiplex Transmission System |
文件: | 总33页 (文件大小:577K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MODEL: DLA1
P1x : Pi 16 + Ai 16 points
R1xx: Ai 16 + Ao 16 points
Multiplex Transmission System
S1xx: Ai 8 + Ao 8 + Di 8 + Do 8 points
U1x : Po 16 + Ao 16 points
STANDARD MULTI-TRANSMISSION UNIT
Functions & Features
•Multiple transmission system without any software by
setting station No.
[3] POWER INPUT
AC Power
•All-in-one (self-contained) hardware
•Twisted-pair cable or fiber optics
•Expansion and branching with Repeaters (model: DAL4)
•Removable terminal block
K: 85 – 132 V AC
(Operational voltage range 85 – 132 V, 47 – 66 Hz)
L: 170 – 264 V AC
(Operational voltage range 170 – 264 V, 47 – 66 Hz)
DC Power
•Error detection
•Monitor LEDs provided for contact I/O units
S: 12 V DC
(Operational voltage range 12 V ±10 %, ripple 10 %p-p max.)
R: 24 V DC
53 (2.09)
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
POW
RUN
SA1
SA2
300
(11.81)
[4] OPTIONS
FIB
ER
LIN
K
blank: none
/Q: With options (specify the specification)
RT
RU
200
(2.87)
mm (inch)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
MODEL: DLA1–[1][2]–[3][4]
/C02: Polyurethane coating
/C03: Rubber coating
ORDERING INFORMATION
• Code number: DLA1–[1][2]-[3][4]
Specify a code from below for each [1] through [4].
(e.g. DLA1-2A1-R/Q)
RELATED PRODUCTS
• Remote I/O interface unit (model: DLC)
• Telemetering unit (model: DLS)
• Repeater (model: DAL4)
• Specify the specification for option code /Q
(e.g. /C01)
• Lightning surge protector (model: MDP-DM3)
• Adapter connector (model: CND)
Refer to each unit specifications.
[1] TRANSMISSION MEDIA
1: Twisted-pair cable
GENERAL SPECIFICATIONS
Construction: Surface mounting; terminal access on the
2: Fiber optics cable
front
7: Twisted-pair – fiber optics (repeater incorporated)
Connection
Transmission line terminal: Euro type connector terminal
[2] I/O SECTION
A1: Di 32 points
(Applicable wire size: ≤ 1.25 mm
Power supply terminal: Euro type connector terminal
(Applicable wire size: ≤ 1.25 mm , stripped length 8 mm)
RUN contact: Euro type connector terminal
2, stripped length 8 mm)
A2: Di 64 points
2
C1: Do 32 points (relay)
C2: Do 32 points (open collector)
C3: Do 64 points (relay)
C4: Do 64 points (open collector)
E1: Di 16 + Do 16 points (relay)
E2 : Di 16 + Do 16 points (open collector)
G1x: Ai 32 points
(Applicable wire size: ≤ 1.25 mm2, stripped length 8 mm)
I/O section:
•32-point I/O (or less): 40-pin connector terminal; M3 × 6
screws (torque 0.7 N·m)
•64-point I/O: FCN 40-pin connector (two);
(FUJITSU FCN-365P040-AU)
M1x: Ao 32 points
Housing material: Flame-resistant resin (beige)
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 1/33
http://www.m-system.co.jp/
MODEL: DLA1
Isolation: I/O to transmission section to power
Station No. setting: 2 rotary switches; 00 – FF (256)
■ Controller & Transmission Sections
Power indicator: Red LED turns ON in normal conditions;
OFF when the voltage level becomes low.
RUN indicator: Red LED turns OFF in error.
■ I/O Section
INSTALLATION
Power consumption
•AC: Approx. 17.5 VA max.
•DC: Approx. 17 W max. (1.1 A with 24 V)
Grounding: Not required in normal environments; 100 Ω or
less grounding resistance in noisy environments
Operating temperature: -5 to + 50°C (23 to 122°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Atmosphere: No corrosive gas or heavy dust
Mounting: Surface; Rack Mounting Frame (model: BX-1DL)
available
Contact I/O indicator LED: Red LEDs turn on when the
respective I/O channels are ON.
Analog I/O CPU RUN indicator LED: Red LED turns ON when
the CPU function proves normal, OFF in error.
■ RUN Contact Output: Contact opens in error.
Rated load: 100 V AC or 30 V DC @ 1 A (resistive load)
Maximum switching voltage: 120 V AC or 30 V DC
Maximum switching power: 100 VA or 30 W
Minimum load: 5 V DC @ 10 mA
Weight: 2 kg (4.4 lb)
PERFORMANCE
Permissible power failure duration: ≤ 20 ms
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 1500 V AC @ 1 minute
(I/O to transmission to power to ground)
Error detection
•Communication: The receiver units detect loss of
communication and wire break.
•CPU: Watch-dog timer
•Power voltage: Detects when the voltage supply to the
CPU drops by 10 %.
MULTIPLEX COMMUNICATION
Communication: Half-duplex, synchronous
Transmission: Conform to RS-422, EIA
Transmission speed: 125 kbps
Protocol: SIN-NET (M-System's; data format conforms to
SDLC)
Error check: CRC
■ Twisted-pair Cable
Cable: CPEV-0.9 dia.
Connection: Euro Type connector terminal
(Applicable wire size: ≤ 1.25 mm , stripped length 8 mm)
2
Transmission Distance: 1 kilometer max. with 16 units
connected; 3 kilometers max. between 2 stations each of
which consists of 3 units
Terminator: Incorporated (Remove the attached jumper pin
when the unit is not located at the end of transmission line.)
■ Fiber Optics Cable
Link: JIS F07 connector (Consult factory for details)
Transmission distance: 1 kilometer max. with PCF
Transmission loss: 7 dB max.
■ Twisted-pair – Fiber Optics: Converting signals between
two media and waveform shaping
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 2/33
http://www.m-system.co.jp/
MODEL: DLA1
DESCRIPTIONS
■ RUN Contact (LED) Behaviors
Input units
Input units (A1, A2, G1 and P1): The LED turns ON with the network built-up; OFF in error; the network is reconfigured after an
error.
•Connecting the input unit to the DLC
The LED remains ON regardless of the input command of the DLC.
Output units
Output units (C1, C2, C3, C4, M1 and U1): The LED turns ON when data from the paired input unit is received normally, with the
network configured; OFF when the data is lost; turns also OFF in error in the network.
Transmission via the DLS units: The LED remains ON regardless of the input unit status or telecomm. line status, once it is
turned ON.
•Connecting the output unit to the DLC
After the output unit receives the output command from the DLC, the LED turns ON and remains ON regardless of the data
update.
I/O-mixed units (E1, E2, R1 and S1): The LED turns ON when data from the paired input unit is received normally, with the
network configured; OFF in case of data loss or network error.
•Connecting the I/O-mixed unit to the DLC
After the I/O unit receives the output command from the DLC regardless whether input or output, the LED turns ON and
remains ON regardless of the data update.
[CAUTION]
When the network is reconfigured e.g. by noise interference, the RUN LED and output for all units on the network turn briefly
OFF until they are turned ON after the reconfiguration is complete.
■ Station Number (Address)
A) 1 input unit and X output units: Match the address for input and output units. The input data can be output at several units.
A 64-point input unit needs two station numbers. Do not assign the number following the one set for a 64-point input unit to
another unit.
B) 64-point contact input unit to 32-point output units: Match the number for input and one output units, then set a consecutive
number for the other output unit.
[example]
input unit → 01
output unit → 01 & 02
C) 32-point contact input units to 64-point output unit: Match the number for the output and one input units, then set a
consecutive number for the other input unit.
[example]
input unit → 01 & 02
output unit → 01
D) I/O mixed units: Set an even number and a consecutive number for the 2 corresponding units.
[example] 02 & 03
A combination of 3 units or more is not allowed.
E) Computer interface: Set address numbers to correspond with the computer as I/O unit.
■ Transmission Time
Integrate all the transmission time for each process input unit in the system.
•Contact input 32 points (A1): 1.5 msec.
•Contact input 64 points (A2): 3.0 msec.
•Contact I/O each 16 points (E1): 1.5 msec.
•Analog input 32 points (G1): 48.0 msec.
•Analog/pulse Input each 16 points (P1): 48.0 msec.
•Analog I/O each 16 points (R1): 24.0 msec.
•Analog & contact I/O each 8 points (S1): 12.0 msec.
An analog unit does not transmit all its points in serial but does 1 point per each cycle. For example, when 1 contact input unit
and 1 analog input unit (32 points for each) are connected, 32 point contact signal and 1 point analog signal are transmitted in
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 3/33
http://www.m-system.co.jp/
MODEL: DLA1
turn. One cycle time is therefore calculated as:
32 times × 1.5 msec. + 48 msec. = 96 msec.
This method is beneficial for giving a priority to contact signals which vary rapidly.
■ TRANSMISSION LINE CONFIGURATION
1. BASIC CONDITIONS
The multi-drop transmission line should fulfill the following conditions. Contact M-System's sales office or representatives
when designing.
A) 10 kilometers at maximum in total system.
B) Twisted-pair cable (code 1): a multi-drop section composed only of twisted-pair cable can have at maximum of
16 units within the total distance of 1 kilometer.
F.O.
T.P
1 km max.
*
7
*
1
.
.
.
.
1
1
1
No. 1
2
3
.
.
.
.
15
16
1 & 7 : TRANSMISSION MEDIA CODE
T.P. : TWISTED-PAIR CABLE
F.O. : FIBER OPTICS CABLE
C) Fiber optics cable (code 2): a system can have at maximum of 6 multi-drop sections composed only of fiber optics.
Insert a pair of units of code "7" for waveform shaping between each 5 units of code "2".
1 kilometer max. between each unit.
T.P
T.P
F.O. F.O.
F.O.
.
F.O.
F.O.
*
*
*
.
.
.
.
7
2
2
2
7
7
No. 1
2
.
.
5
2 & 7 : TRANSMISSION MEDIA CODE
T.P. : TWISTED-PAIR CABLE
F.O. : FIBER OPTICS CABLE
D) Twisted-pair & fiber optics (code 7): a transmission line can have at maximum of 8 units of code "7". Units of code "1"
and "2" can be mixed in each section within the above limitation.
T.P
T.P
T.P
T.P
F.O.
F.O.
F.O.
F.O.
*
*
*
*
*
7
5
*
*
7
7
*
7
8
7
7
7
7
7
No. 1
2
:
3
4
6
7
TRANSMISSION MEDIA CODE
T.P. : TWISTED-PAIR CABLE
F.O. : FIBER OPTICS CABLE
* Marked units are located at the end of transmission line via twisted-pair cable. Short across the terminals 6 – 7 with the jumper pin provided
with the units.
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 4/33
http://www.m-system.co.jp/
MODEL: DLA1
2. LONG DISTANCE TRANSMISSION
A) Twisted-pair transmission between point A to pointB:
3kilometersatmaximiumbetweentwopoints when 3 units are mounted closely side by side at each point.
With each additional unit, the distance is reduced by 100 meters.
POINT A
POINT B
*
*
3 km max.
1
1
2
1
3
1
1
1
No. 1
1
4
5
6
:
TRANSMISSION MEDIA CODE
B) Twisted-pair cable between 6 points (special case of 1-D)
2 kilometers at maximum with twisted-pair cable between each point.
4sectionsatmaximumwithfiberoptics;1kilometerat maximum for each section. Total distance within 10 kilometers.
T.P
2 km max.
T.P
T.P
T.P
T.P
F.O.
F.O.
F.O.
F.O.
*
*
*
*
*
*
*
*
*
*
1
7
7
7
7
7
7
7
7
1
1
2
3
4
POINT A POINT B
POINT C
POINT D
POINT E POINT F
1 & 7 : TRANSMISSION MEDIA CODE
T.P. : TWISTED-PAIR CABLE
F.O. : FIBER OPTICS CABLE
* Marked units are located at the end of transmission line via twisted-pair cable. Short across the terminals 6 – 7 with the jumper pin provided
with the units.
3. INTERSECTION
When units cannot be connected in serial, use a pair of units of code"7" at the intersection (marked with *) or model DAL4.
(
)
*
(
)
*
(
)
( )
*
*
(detail of the intersection)
T.P.
T.P.
F.O.
7
7
• BRANCHING VIA DAL4
• BRANCHING VIA DLA1
4. COMBINATION WITH MODEL DAL4
2 kilometersmax.betweentwoDAL4units. 1kilometer max. when there are other units between the DAL4 units.
Total number of DAL4 on the transmission line must be 6 units or less, with the total distance 10 kilometers max.
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 5/33
http://www.m-system.co.jp/
MODEL: DLA1
■ CONBINATION TABLE
POSSIBLE COMBINATION
REMARKS
DLA1-xA1 (Di 32 points)
DLA1-xA2 (Di 64 points)
DLA1-xC1 (Do 32 points) DLA1-x C2 (Do 32 points) Two A1 units required for
DLA1-xC3 (Do 64 points) DLA1-x C4 (Do 64 points) one C3 or C4 unit.
DLA1-xC1 (Do 32 points) DLA1-x C2 (Do 32 points) Two C1 or C2 units required
DLA1-xC3 (Do 64 points) DLA1-x C4 (Do 64 points) for one A2 unit.
DLA1-xC1 (Do 32 points)
DLA1-xC2 (Do 32 points)
DLA1-xA1 (Di 32 points) DLA1-x A2 (Di 32 points) Two C1 or C2 units required
for one A2 unit.
DLA1-xC3 (Do 64 points)
DLA1-xC4 (Do 64 points)
DLA1-xA1 (Di 32 points) DLA1-x A2 (Di 32 points) Two A1 units required for
one C3 or C4 unit.
DLA1-xE1 (Di 16 + Do 16)
DLA1-xE2 (Di 16 + Do 16)
DLA1-xE1 (Di 16 + Do 16)
DLA1-xE2 (Di 16 + Do 16)
DLA1-xG1 (Ai 32 points)
DLA1-xM1 (Ao 32 points)
DLA1-xP1 (Pi 16 + Ai 16)
DLA1-xM1 (Ao 32 points)
DLA1-xG1 (Ai 32 points)
DLA1-xU1 (Po 16 + Ao 16)
DLA1-xM1 (Ao 16 [accum. value] + Ao 16
M1 outpus analog signal in pro-
Proporition to accumulated pulse.
DLA1-xR1 (Ai 16 + Ao 16)
DLA1-xR1 (Ai 16 + Ao 16)
DLA1-xS1 (Ai 8+Ao 8+Di 8+Do 8) DLA1-xS1 (Ai 8 + Ao 8 + Di 8 + Do 8)
DLA1-xU1 (Po 16 + Ao 16)
DLA1-xP1 (Pi 16 + Ai 16)
EXTERNAL VIEW
Power LED Indicator
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
RUN LED Indicator
Station No. Setting
Rotary Switches
SA1
SA2
■
STANDARD TYPE
■DLA1-A2, C3, C4
I/O Indicator LEDs
(40-terminal connector)
(FCN 40-pin connectors)
(Varies according to I/O types.
See each I/O section.)
1
3
5
7
LED Indicator
Selector
U
L
2
4
6
8
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
■TWISTED-PAIR
■FIBER OPTICS
■
TWISTED-PAIR & FIBER
CN1
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Fiber Link
Connector
Fiber Link
Connector
Fiber Link
Connector
9
8
7
6
5
4
9
8
Jumper
Jumper
CN2
7
6
5
4
5
4
Euro Type
Connector
Terminal
Euro Type
Connector
Terminal
Euro Type
Connector
Terminal
3
2
1
3
2
1
3
2
1
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 6/33
http://www.m-system.co.jp/
MODEL: DLA1
CONNECTION DIAGRAM
■ TWISTED-PAIR CABLE
(transmission media code: 1)
■ FIBER OPTICS CABLE
(transmission media code: 2)
■ TWISTED-PAIR & FIBER OPTICS
(transmission media code: 7)
FIBER - OPTIC
CONNECTOR
FIBER - OPTIC
CONNECTOR
Fiber Optics
FIBER - OPTIC
CONNECTOR
Fiber Optics
Shielded
Twisted-pair Cable
Shielded
Twisted-pair Cable
+
–
+
–
9
8
7
6
5
4
3
2
1
9
8
7
6
5
4
3
2
1
JUMPER PIN*
JUMPER PIN*
5
RUN CONTACT OUTPUT
EARTH (FG)
RUN CONTACT OUTPUT
RUN CONTACT OUTPUT
EARTH (FG)
4
EARTH (FG)
V(–)
3
2
1
V(–)
POWER
U(+)
V(–)
POWER
U(+)
POWER
U(+)
*When the unit is located at the end of transmission line via twisted-pair cable (= no cross-wiring),
short across the terminals 6 – 7 with the jumper pin (or wire) provided with the unit.
Remove the jumper pin for the one not located at the end.
EXTERNAL DIMENSIONS unit: mm (inch)
■STANDARD TYPE (DLA1-xA1, xC1, xC2, xE1, xE2, xG1, xM1, xP1, xR1, xS1, xU1)
SIDE MOUNTING 4 – 4.4 (.17) dia.
[53 (2.09) deep]
SURFACE MOUNTING M4 SCREW
[7 (.28) deep]
•40-pin Connector Terminal Block
1
2
3
5
7
9
4
6
8
10
11
12
13
14
15
16
17
18
19
20
21
22
23
40–M3 SCREW
TERMINAL
24
26
28
30
32
34
36
38
40
25
27
29
31
33
35
37
39
3.5 (.14)
170 (6.69)
200 (7.87)
53 (2.09)
28 (1.10)
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 7/33
http://www.m-system.co.jp/
MODEL: DLA1
■ WITH I/O CONNECTORS (DLAx-xA2, xC3, xC4)
SIDE MOUNTING 4 – 4.4 (.17) dia.
[53 (2.09) deep]
SURFACE MOUNTING M4 SCREW
[7 (.28) deep]
•Connector Pin Assignment
LED INDICATOR
SELECTOR
U
L
A1
B1
CN1
CN2
A20
A1
B20
B1
A20
B20
3.5 (.14)
170 (6.69)
200 (7.87)
53 (2.09)
80 (3.15) min.
•Terminal Assignment, Euro Type Connector Terminals
•Wiring Procedure of Euro Type Connector Terminals
PIN TERMINAL
PHOENIX CONTACT AI 1,5-8BK RECOMMENDED
MULTI-STRAND CABLE: 1.25 mm2 (.02 in2)
MINUS SCREWDRIVER
9
*
8
7
6
5
4
SOLID CABLE
1.4 mm (.06) dia.
Remove cover.
8 mm (.32)
3
2
1
*
Not provided for fiber optics (code 2)
Note : There is no specific order for connecting fiber optics.
MOUNTING REQUIREMENTS unit: mm (inch)
■ SURFACE MOUNTING
■ SIDE MOUNTING (terminal block at the right side)
55
55
2–M4 SCREW
4–M4 SCREW
(2.17) (2.17)
3.5 (.14)
170 (6.69)
WIRING SPACE
95 (3.74) MIN.
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 8/33
http://www.m-system.co.jp/
MODEL: DLA1
FUNCTION BLOCK DIAGRAM
POWER TERMINALS
MULTI-XMISSION TERMINALS
1
2
6
7
8
9
4 5
Multi-Xmission
Interface
RUN Relay
Contact
Isolation
Circuit
RUN
LED
RUN
Controller
Network
CPU
Watch-dog
POWER LED
EP ROM
Station No.
Set SW
Common RAM
or Latching Circuit
I/O
Controller
*
Isolation
Circuit
Contact I/O
Indicator LEDs***
I/O
Driver
I/O CPU
RUN LED**
**
MODULAR JACK
I/O TERMINALS
*Deleted with Codes G1, P1, R1 or S1.
**Deleted with Codes A1, A2, C1, C2, C3, C4, E1 or E2.
Deleted with Codes G1, M1, R1.
***
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 9/33
http://www.m-system.co.jp/
MODEL: DLA1
CONTACT INPUT UNIT
INPUT SPECIFICATIONS
(Di 32 points)
Input: Dry contact, 32 points
Commons: All negatives
Sensing: Approx. 15 V DC @ 3 mA
ON/OFF level: ≤ 200 Ω for ON; ≥ 100 kΩ for OFF
MODEL: DLA1–[1]A1–[2][3]
ORDERING INFORMATION
• Code number: DLA1–[1]A1-[2][3]
Specify a code from below for each [1] through [3].
(e.g. DLA1-2A1-K/Q)
PERFORMANCE
Multi-transmission time: 1.5 msec.
Input read time: 5 msec. per 32 points
• Specify the specification for option code /Q
(e.g. /C01)
EXTERNAL VIEW
Contact input
Indicator LED
[1] TRANSMISSION MEDIA
1: Twisted-pair cable
2: Fiber optics cable
40-pin Connector
Terminal Block
7: Twisted-pair – fiber optics (repeater incorporated)
[2] POWER INPUT
AC Power
K: 85 – 132 V AC
(Operational voltage range 85 – 132 V, 47 – 66 Hz)
L: 170 – 264 V AC
CONNECTION DIAGRAM
■ INPUT
(Operational voltage range 170 – 264 V, 47 – 66 Hz)
DC Power
Di 1
1
Di 2
2
S: 12 V DC
Di 3
3
(Operational voltage range 12 V ±10 %, ripple 10 %p-p max.)
R: 24 V DC
Di 4
4
Di 5
5
Di 6
6
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
Di 7
7
Di 8
8
Di 9
9
Di 10
Di 11
Di 12
Di 13
Di 14
Di 15
Di 16
Di 17
Di 18
Di 19
Di 20
Di 21
Di 22
Di 23
Di 24
Di 25
Di 26
Di 27
Di 28
Di 29
Di 30
Di 31
Di 32
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
[3] OPTIONS
blank: none
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
GENERAL SPECIFICATIONS
Connection
Input: 40-pin connector terminal;
M3 screws (torque: 0.7 N·m)
Applicable wire size: 0.75 mm
2
+
–
Do not use.
Isolation: Input to transmission to power
Contact input indicator LED: Red LEDs turn on when the
respective input channels are ON.
COM(–)
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 10/33
http://www.m-system.co.jp/
MODEL: DLA1
(L)
CONTACT INPUT UNIT
Isolation: Input to transmission to power
Contact input indicator LED: Red LEDs turn on when the
respective input channels are ON.
(Di 64 points)
MODEL: DLA1–[1]A2–[2][3]
INPUT SPECIFICATIONS
Input: Dry contact, 64 points
ORDERING INFORMATION
• Code number: DLA1–[1]A2-[2][3]
Specify a code from below for each [1] through [3].
(e.g. DLA1-2A2-K/Q)
Commons: All negatives
Sensing: Approx. 15 V DC @ 3 mA
ON/OFF level: ≤ 200 Ω for ON; ≥ 100 kΩ for OFF
• Specify the specification for option code /Q
(e.g. /C01)
PERFORMANCE
Multi-transmission time: 3 msec.
[1] TRANSMISSION MEDIA
1: Twisted-pair cable
Input read time: 10 msec. per 64 points
2: Fiber optics cable
EXTERNAL VIEW
7: Twisted-pair – fiber optics (repeater incorporated)
Contact Input
Indicator LED
[2] POWER INPUT
AC Power
K: 85 – 132 V AC
(Operational voltage range 85 – 132 V, 47 – 66 Hz)
L: 170 – 264 V AC
CN1
SW
(Operational voltage range 170 – 264 V, 47 – 66 Hz)
DC Power
CN2
U
L
LED Indicator
Selector
S: 12 V DC
(Operational voltage range 12 V ±10 %, ripple 10 %p-p max.)
R: 24 V DC
CONNECTOR PIN ASSIGNMENT
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
■CONNECTOR CN1
■CONNECTOR CN2
PIN
NO.
CH.
NO.
PIN
NO.
CH.
NO.
PIN
NO.
CH.
NO.
PIN
NO.
CH.
NO.
[3] OPTIONS
blank: none
A1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Di 1
B1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Di17
A1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Di33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
B1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Di49
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
50
/Q: With options (specify the specification)
19
20
21
22
23
24
25
26
27
28
29
30
31
32
51
52
53
54
55
56
57
58
59
60
61
62
63
64
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
RELATED PRODUCTS
• Connector terminal block (model: CNT)
• Special cable with 40-pin connector (model: FCN)
17 C1
18 C1
19 C1
20 C1
17 C1
18 C1
19 C1
20 C1
17 C1
18 C1
19 C1
20 C1
17 C1
18 C1
19 C1
20 C1
GENERAL SPECIFICATIONS
Connection
C1: negative common to all channels
Input: FCN 40-pin connector (two);
(FUJITSU FCN-365P040-AU)
LED indicator selector: Switching between CN1 (U) and CN2
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 11/33
http://www.m-system.co.jp/
MODEL: DLA1
CONTACT OUTPUT UNIT
OUTPUT SPECIFICATIONS
(Do 32 points; relay contact)
Commons: Per 4 points; common current 4A max.
Output: Relay contact, 32 points
Contact rating: 120 V AC @ 1 A (cos ø = 1)
30 V DC @ 1 A (resistive load)
MODEL: DLA1–[1]C1–[2][3]
Maximum switching voltage: 120 V AC or 30 V DC
Maximum switching power: 120 VA or 30 W
Minimum load: 5 V DC @ 10 mA
ORDERING INFORMATION
• Code number: DLA1–[1]C1–[2][3]
Specify a code from below for each [1] through [3].
(e.g. DLA1-2C1-K/Q)
Mechanical life: 5 x 10 cycles
7
For maximum relay life with inductive loads, external
protection is recommended.
• Specify the specification for option code /Q
(e.g. /C01)
PERFORMANCE
Output time
[1] TRANSMISSION MEDIA
1: Twisted-pair cable
OFF to ON: 8 msec. per 32 points
ON to OFF: 3 msec. per 32 points
2: Fiber optics cable
7: Twisted-pair – fiber optics (repeater incorporated)
EXTERNAL VIEW
[2] POWER INPUT
Contact output
Indicator LED
AC Power
K: 85 – 132 V AC
(Operational voltage range 85 – 132 V, 47 – 66 Hz)
L: 170 – 264 V AC
40-pin Connector
Terminal Block
(Operational voltage range 170 – 264 V, 47 – 66 Hz)
DC Power
S: 12 V DC
(Operational voltage range 12 V ±10 %, ripple 10 %p-p max.)
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
[3] OPTIONS
blank: none
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
GENERAL SPECIFICATIONS
Connection
Output: 40-pin connector terminal; M3 screws
(torque 0.7 N·m)
Applicable wire size: 0.75 mm
2
Isolation: Output to transmission to power
Contact output indicator LED: Red LEDs turn on when the
respective output channels are ON.
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 12/33
http://www.m-system.co.jp/
MODEL: DLA1
CONNECTION DIAGRAM
■ OUTPUT
Do 1
1
Do 2
2
Do 3
3
Do 4
4
COM1(–)
Do 5
5
6
Do 6
7
Do 7
8
Do 8
9
COM2(–)
Do 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Do 10
Do 11
Do 12
COM3(–)
Do 13
Do 14
Do 15
Do 16
COM4(–)
Do 17
Do 18
Do 19
Do 20
COM5(–)
Do 21
Do 22
Do 23
Do 24
COM6(–)
Do 25
Do 26
Do 27
Do 28
COM7(–)
Do 29
Do 30
Do 31
Do 32
COM8(–)
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 13/33
http://www.m-system.co.jp/
MODEL: DLA1
CONTACT OUTPUT UNIT
OUTPUT SPECIFICATIONS
(Do 32 points; open collector)
Commons: All negatives
Output: Open collector, 32 points
Contact rating: 30 V DC @ 100 mA (resistive load) External
protection is recommended with inductive loads.
Saturation voltage: 1.6 V DC
MODEL: DLA1–[1]C2–[2][3]
ORDERING INFORMATION
• Code number: DLA1–[1]C2–[2][3]
Specify a code from below for each [1] through [3].
(e.g. DLA1-2C2-K/Q)
PERFORMANCE
Output time: 3 msec. per 32 points
• Specify the specification for option code /Q
(e.g. /C01)
EXTERNAL VIEW
Contact output
Indicator LED
[1] TRANSMISSION MEDIA
1: Twisted-pair cable
2: Fiber optics cable
40-pin Connector
Terminal Block
7: Twisted-pair – fiber optics (repeater incorporated)
[2] POWER INPUT
AC Power
K: 85 – 132 V AC
(Operational voltage range 85 – 132 V, 47 – 66 Hz)
L: 170 – 264 V AC
CONNECTION DIAGRAM
■ OUTPUT
(Operational voltage range 170 – 264 V, 47 – 66 Hz)
DC Power
Do 1
1
S: 12 V DC
Do 2
2
Do 3
3
(Operational voltage range 12 V ±10 %, ripple 10 %p-p max.)
R: 24 V DC
Do 4
4
Do 5
5
Do 6
6
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
Do 7
7
Do 8
8
CLAMP1
COM(–)
Do 9
9
[3] OPTIONS
blank: none
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Do 10
Do 11
Do 12
Do 13
Do 15
Do 15
Do 16
CLAMP2
COM(–)
Do 17
Do 18
Do 19
Do 20
Do 21
Do 22
Do 23
Do 24
CLAMP3
COM(–)
Do 25
Do 26
Do 27
Do 28
Do 29
Do 30
Do 31
Do 32
CLAMP4
COM(–)
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
GENERAL SPECIFICATIONS
Connection
Output: 40-pin connector terminal; M3 screws
(torque 0.7 N·m)
Applicable wire size: 0.75 mm
2
Isolation: Output to transmission to power
Contact output indicator LED: Red LEDs turn on when the
respective output channels are ON.
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 14/33
http://www.m-system.co.jp/
MODEL: DLA1
CONTACT OUTPUT UNIT
GENERAL SPECIFICATIONS
(Do 64 points; relay contact)
Connection:
Output: FCN 40-pin connector (two);
(FUJITSU FCN-365P040-AU)
MODEL: DLA1–[1]C3–[2][3]
LED indicator selector: Switching between CN1 (U) and
CN2 (L)
ORDERING INFORMATION
• Code number: DLA1–[1]C3–[2][3]
Specify a code from below for each [1] through [3].
(e.g. DLA1-2C3-K/Q)
Isolation: Output to transmission to power
Contact output indicator LED: Red LEDs turn on when the
respective output channels are ON.
• Specify the specification for option code /Q
(e.g. /C01)
OUTPUT SPECIFICATIONS
Common: Per 4 points
Common current: Max. 0.8 A
[1] TRANSMISSION MEDIA
1: Twisted-pair cable
Output: Relay contact, 64 points
Contact rating: 120 V AC @ 0.8 A (cos ø = 1)
30 V DC @ 0.8 A (resistive load)
2: Fiber optics cable
7: Twisted-pair – fiber optics (repeater incorporated)
Maximum switching voltage: 120 V AC or 30 V DC
Maximum switching power: 96 VA or 24 W
Minimum load: 5 V DC @ 10 mA
[2] POWER INPUT
AC Power
Mechanical life: 5 × 10 cycles
7
For maximum relay life with inductive loads, external
protection is recommended.
K: 85 – 132 V AC
(Operational voltage range 85 – 132 V, 47 – 66 Hz)
L: 170 – 264 V AC
(Operational voltage range 170 – 264 V, 47 – 66 Hz)
DC Power
PERFORMANCE
Output time
S: 12 V DC
OFF to ON: 8 msec. per 64 points
ON to OFF: 6 msec. per 64 points
(Operational voltage range 12 V ±10 %, ripple 10 %p-p max.)
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
EXTERNAL VIEW
Contact Output
Indicator LED
[3] OPTIONS
blank: none
/Q: With options (specify the specification)
CN1
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
SW
CN2
U
L
LED Indicator
Selector
/C02: Polyurethane coating
/C03: Rubber coating
RELATED PRODUCTS
• Connector terminal block (model: CNT)
• Special cable with 40-pin connector (model: FCN)
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 15/33
http://www.m-system.co.jp/
MODEL: DLA1
CONNECTOR PIN ASSIGNMENT
■ CONNECTOR CN1
■ CONNECTOR CN2
PIN CH. PIN
NO. NO. NO.
CH.
NO.
PIN CH. PIN
NO. NO. NO.
CH.
NO.
A1 Do 1 B1 Do17
A1 Do33 B1 Do49
2
2
3
4
2
18
19
20
2
3
4
34
35
36
2
3
4
50
51
52
3
3
4
17 C1
4
17 C5
17 C9
17 C13
5
6
7
8
Do 5
5
6
7
8
Do21
22
23
5
6
7
8
Do37
5
6
7
8
Do53
54
55
6
7
8
38
39
40
24
56
18 C2
18 C6
18 C10
18 C14
9
10
11
12
Do 9
9
10
Do25
9
10
11
12
Do41
42
43
9
10
11
12
Do57
58
59
10
11
12
26
27
28
11
12
44
60
19 C3
19 C7
19 C11
19 C15
13 Do13
13 Do29
13 Do45
13 Do61
14
15
16
14
15
16
14
15
30
31
32
14
15
16
46
47
48
14
15
16
62
63
64
16
20 C4
20 C8
20 C12
20 C16
C1 – C16: negative common per 4 points
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 16/33
http://www.m-system.co.jp/
MODEL: DLA1
CN2 (L)
CONTACT OUTPUT UNIT
Isolation: Output to transmission to power
Contact output indicator LED: Red LEDs turn on when the
respective output channels are ON.
(Do 64 points; open collector)
MODEL: DLA1–[1]C4–[2][3]
OUTPUT SPECIFICATIONS
Commons: All negatives
ORDERING INFORMATION
• Code number: DLA1–[1]C4–[2][3]
Specify a code from below for each [1] through [3].
(e.g. DLA1-2C4-K/Q)
Output: Open collector, 64 points
Contact rating: 30 V DC @ 100 mA (resistive load)
External protection is recommended with inductive loads.
Saturation voltage: 1.6 V DC
• Specify the specification for option code /Q
(e.g. /C01)
PERFORMANCE
Output time: 6 msec. per 64 points
[1] TRANSMISSION MEDIA
1: Twisted-pair cable
2: Fiber optics cable
EXTERNAL VIEW
7: Twisted-pair – fiber optics (repeater incorporated)
Contact Output
Indicator LED
[2] POWER INPUT
AC Power
K: 85 – 132 V AC
(Operational voltage range 85 – 132 V, 47 – 66 Hz)
L: 170 – 264 V AC
CN1
SW
(Operational voltage range 170 – 264 V, 47 – 66 Hz)
DC Power
CN2
U
L
LED Indicator
Selector
S: 12 V DC
(Operational voltage range 12 V ±10 %, ripple 10 %p-p max.)
R: 24 V DC
CONNECTOR PIN ASSIGNMENT
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
■ CONNECTOR CN1
■ CONNECTOR CN2
PIN CH. PIN
NO. NO. NO.
CH.
NO.
PIN CH. PIN
NO. NO. NO.
CH.
NO.
[3] OPTIONS
A1 Do 1 B1 Do17
A1 Do33 B1 Do49
blank: none
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
18
19
20
21
22
23
24
2
3
4
5
6
7
8
34
35
36
37
38
39
40
2
3
4
5
6
7
8
50
51
52
53
54
55
56
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
17 C1
18 C1
17 C1
18 C1
17 C1
18 C1
17 C1
18 C1
/C02: Polyurethane coating
/C03: Rubber coating
9
10
11
12
13
14
15
16
Do 9
10
11
9
10
11
12
13
14
15
16
Do25
26
27
9
10
11
12
13
14
15
16
Do41
9
10
11
12
13
14
15
16
Do57
58
59
42
43
44
45
46
47
48
12
13
14
15
28
29
30
31
60
61
62
63
RELATED PRODUCTS
• Connector terminal block (model: CNT)
• Special cable with 40-pin connector (model: FCN)
16
32
64
19 C1
20 CL1
19 C1
20 CL2
19 C1
20 CL3
19 C1
20 CL4
GENERAL SPECIFICATIONS
Connection:
C1: negative common to all channels
CL1 – CL4: clamp terminals per 16 points
Output: FCN 40-pin connector (two);
(FUJITSU FCN-365P040-AU)
LED indicator selector: Switching between CN1 (U) and
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 17/33
http://www.m-system.co.jp/
MODEL: DLA1
CONTACT I/O UNIT
INPUT SPECIFICATIONS
(Di 16 + Do 16 points; relay contact output)
Input: Dry contact, 16 points
Commons: All negatives
Sensing: Approx. 15 V DC @ 3 mA
ON/OFF level: ≤ 200 Ω for ON; ≥ 100 kΩ for OFF
MODEL: DLA1–[1]E1–[2][3]
ORDERING INFORMATION
• Code number: DLA1–[1]E1–[2][3]
Specify a code from below for each [1] through [3].
(e.g. DLA1-2E1-K/Q)
OUTPUT SPECIFICATIONS
Commons: Per 4 points; common current 4A max.
Output: Relay contact, 16 points
Contact rating: 120 V AC @ 1 A (cos ø = 1)
30 V DC @ 1 A (resistive load)
• Specify the specification for option code /Q
(e.g. /C01)
Maximum switching voltage: 120 V AC or 30 V DC
Maximum switching power: 120 VA or 30 W
Minimum load: 5 V DC @ 10 mA
[1] TRANSMISSION MEDIA
1: Twisted-pair cable
Mechanical life: 5 × 10 cycles
7
2: Fiber optics cable
For maximum relay life with inductive loads, external
protection is recommended.
7: Twisted-pair – fiber optics (repeater incorporated)
[2] POWER INPUT
AC Power
PERFORMANCE
Multi-transmission time: 1.5 msec.
Input read time: 3 msec. per 16 points
Output time
K: 85 – 132 V AC
(Operational voltage range 85 – 132 V, 47 – 66 Hz)
L: 170 – 264 V AC
OFF to ON: 8 msec. per 16 points
ON to OFF: 3 msec. per 16 points
(Operational voltage range 170 – 264 V, 47 – 66 Hz)
DC Power
S: 12 V DC
EXTERNAL VIEW
(Operational voltage range 12 V ±10 %, ripple 10 %p-p max.)
R: 24 V DC
Contact I/O
Indicator LED
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
40-pin Connector
Terminal Block
[3] OPTIONS
blank: none
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
GENERAL SPECIFICATIONS
Connection:
I/O: 40-pin connector terminal; M3 screws
(torque 0.7 N·m)
Applicable wire size: 0.75 mm
2
Isolation: I/O to transmission to power
Contact I/O indicator LED: Red LEDs turn on when the
respective I/O channels are ON.
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 18/33
http://www.m-system.co.jp/
MODEL: DLA1
CONNECTION DIAGRAM
■ I/O
Di 1
1
Di 2
2
+
–
Di 3
3
Di 4
4
COM1(–)
Di 5
5
6
Di 6
7
Di 7
8
Di 8
9
COM1(–)
Di 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Di 10
Di 11
Di 12
COM1(–)
Di 13
Di 14
Di 15
Di 16
COM1(–)
Do 1
Do 2
Do 3
Do 4
COM2(–)
Do 5
Do 6
Do 7
Do 8
COM3(–)
Do 9
Do 10
Do 11
Do 12
COM4(–)
Do 13
Do 14
Do 15
Do 16
COM5(–)
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 19/33
http://www.m-system.co.jp/
MODEL: DLA1
CONTACT I/O UNIT
INPUT SPECIFICATIONS
(Di 16 + Do 16 points; open collector output)
Input: Dry contact, 16 points
Commons: All negatives
Sensing: Approx. 15 V DC @ 3 mA
ON/OFF level: ≤ 200 Ω for ON; ≥ 100 kΩ for OFF
MODEL: DLA1–[1]E2–[2][3]
ORDERING INFORMATION
• Code number: DLA1–[1]E2–[2][3]
Specify a code from below for each [1] through [3].
(e.g. DLA1-2E2-K/Q)
OUTPUT SPECIFICATIONS
Commons: All negatives
Output: Open collector, 16 points
Contact rating: 30 V DC @ 100 mA (resistive load)
External protection is recommended with inductive loads.
Saturation voltage: 1.6 V DC
• Specify the specification for option code /Q
(e.g. /C01)
[1] TRANSMISSION MEDIA
1: Twisted-pair cable
PERFORMANCE
Multi-transmission time: 1.5 msec.
Input read time: 3 msec. per 16 points
Output time: 3 msec. per 16 points
2: Fiber optics cable
7: Twisted-pair – fiber optics (repeater incorporated)
[2] POWER INPUT
AC Power
EXTERNAL VIEW
Contact I/O
Indicator LED
K: 85 – 132 V AC
(Operational voltage range 85 – 132 V, 47 – 66 Hz)
L: 170 – 264 V AC
40-pin Connector
Terminal Block
(Operational voltage range 170 – 264 V, 47 – 66 Hz)
DC Power
S: 12 V DC
(Operational voltage range 12 V ±10 %, ripple 10 %p-p max.)
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
[3] OPTIONS
blank: none
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
GENERAL SPECIFICATIONS
Connection:
I/O: 40-pin connector terminal; M3 screws
(torque 0.7 N·m)
Applicable wire size: 0.75 mm
2
Isolation: I/O to transmission to power
Contact I/O indicator LED: Red LEDs turn on when the
respective I/O channels are ON.
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 20/33
http://www.m-system.co.jp/
MODEL: DLA1
CONNECTION DIAGRAM
■ I/O
Di 1
1
Di 2
2
+
–
Di 3
3
Di 4
4
COM1(–)
Di 5
5
6
Di 6
7
Di 7
8
Di 8
9
COM1(–)
Di 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Di 10
Di 11
Di 12
COM1(–)
Di 13
Di 14
Di 15
Di 16
COM1(–)
Do 1
Do 2
Do 3
Do 4
Do 5
Do 6
Do 7
Do 8
CLAMP1
COM1(–)
Do 9
Do 10
Do 11
Do 12
Do 13
Do 14
Do 15
Do 16
CLAMP2
COM2(–)
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 21/33
http://www.m-system.co.jp/
MODEL: DLA1
ANALOG INPUT UNIT
GENERAL SPECIFICATIONS
(Ai 32 points)
Connection
Input: 40-pin connector terminal;
M3 screws (torque: 0.7 N·m)
MODEL: DLA1–[1]G1[2]–[3][4]
Applicable wire size: 0.75 mm
2
Isolation: Input to transmission to power
Input CPU RUN indicator LED: Red LED turns ON when the
CPU operates normally.
ORDERING INFORMATION
• Code number: DLA1–[1]G1[2]-[3][4]
Specify a code from below for each [1] through [4].
(e.g. DLA1-2G1A4-R/Q)
INPUT SPECIFICATIONS
Input: DC voltage, 32 points
• Specify the specification for option code /Q
(e.g. /C01)
Operational range: -1.5 – +11.5 V DC
Commons: All negatives
[1] TRANSMISSION MEDIA
1: Twisted-pair cable
PERFORMANCE
Accuracy: ±10 mV
2: Fiber optics cable
7: Twisted-pair – fiber optics (repeater incorporated)
Temp. coefficient: ±1.5 mV/°C (±0.9 mV/°F)
Multi-transmission time: 48 msec.
Input read time: 300 msec. per 32 points
[2] INPUT
Voltage
A4: 0 – 10 V DC(Input resistance 1 MΩ min.)
A5: 0 – 5 V DC(Input resistance 1 MΩ min.)
A6: 1 – 5 V DC (Input resistance 1 MΩ min.)
EXTERNAL VIEW
Input CPU
RUN Indicator
[3] POWER INPUT
AC Power
Modular Jack
40-pin Connector
Terminal Block
K: 85 – 132 V AC
(Operational voltage range 85 – 132 V, 47 – 66 Hz)
L: 170 – 264 V AC
(Operational voltage range 170 – 264 V, 47 – 66 Hz)
DC Power
S: 12 V DC
(Operational voltage range 12 V ±10 %, ripple 10 %p-p max.)
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
[4] OPTIONS
blank: none
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 22/33
http://www.m-system.co.jp/
MODEL: DLA1
CONNECTION DIAGRAM
■ INPUT
Ai 1
1
Ai 2
2
Ai 3
3
Ai 4
4
Ai 5
5
Ai 6
6
Ai 7
7
Ai 8
8
Ai 9
9
Ai 10
Ai 11
Ai 12
Ai 13
Ai 14
Ai 15
Ai 16
Ai 17
Ai 18
Ai 19
Ai 20
Ai 21
Ai 22
Ai 23
Ai 24
Ai 25
Ai 26
Ai 27
Ai 28
Ai 29
Ai 30
Ai 31
Ai 32
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Do not use.
COM(–)
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 23/33
http://www.m-system.co.jp/
MODEL: DLA1
ANALOG OUTPUT UNIT
GENERAL SPECIFICATIONS
(Ao 32 points)
Connection
Output: 40-pin connector terminal; M3 screws
(torque 0.7 N·m)
MODEL: DLA1–[1]M1[2]–[3][4]
Applicable wire size: 0.75 mm
2
Isolation: Output to transmission to power
Output CPU RUN indicator LED: Red LED turns ON when the
CPU operates normally.
ORDERING INFORMATION
• Code number: DLA1–[1]M1[2]-[3][4]
Specify a code from below for each [1] through [4].
(e.g. DLA1-2M1B4-K/Q)
OUTPUT SPECIFICATIONS
Commons: All negatives
• Specify the specification for option code /Q
(e.g. /C01)
Output: DC voltage, 32 points
Operational range: -1.5 – +11.5 V DC
[1] TRANSMISSION MEDIA
1: Twisted-pair cable
PERFORMANCE
Accuracy: ±10 mV
2: Fiber optics cable
7: Twisted-pair – fiber optics (repeater incorporated)
Temp. coefficient: ±1.5 mV/°C (±0.9 mV/°F)
Output time: 200 msec. per 32 points
[2] OUTPUT
Voltage
EXTERNAL VIEW
B4: 0 – 10 V DC (Load resistance 10 kΩ min.)
B5: 0 – 5 V DC (Load resistance 10 kΩ min.)
B6: 1 – 5 V DC (Load resistance 10 kΩ min.)
Output CPU
RUN Indicator
Modular Jack
40-pin Connector
Terminal Block
[3] POWER INPUT
AC Power
K: 85 – 132 V AC
(Operational voltage range 85 – 132 V, 47 – 66 Hz)
L: 170 – 264 V AC
(Operational voltage range 170 – 264 V, 47 – 66 Hz)
DC Power
S: 12 V DC
(Operational voltage range 12 V ±10 %, ripple 10 %p-p max.)
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
[4] OPTIONS
blank: none
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 24/33
http://www.m-system.co.jp/
MODEL: DLA1
CONNECTION DIAGRAM
■ OUTPUT
Ao 1
1
Ao 2
2
Ao 3
3
Ao 4
4
Ao 5
5
Ao 6
6
Ao 7
7
Ao 8
8
Ao 9
9
Ao 10
Ao 11
Ao 12
Ao 13
Ao 14
Ao 15
Ao 16
Ao 17
Ao 18
Ao 19
Ao 20
Ao 21
Ao 22
Ao 23
Ao 24
Ao 25
Ao 26
Ao 27
Ao 28
Ao 29
Ao 30
Ao 31
Ao 32
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Do not use.
COM(–)
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 25/33
http://www.m-system.co.jp/
MODEL: DLA1
PULSE & ANALOG INPUT UNIT
GENERAL SPECIFICATIONS
(Pi 16 + Ai 16 points)
Connection
Input: 40-pin connector terminal;
M3 screws (torque: 0.7 N·m)
MODEL: DLA1–[1]P1[2]–[3][4]
Applicable wire size: 0.75 mm
2
Isolation: Input to transmission to power
Pulse input indicator LED: Red LEDs turn on when the
respective input channels are closed.
ORDERING INFORMATION
• Code number: DLA1–[1]P1[2]-[3][4]
Specify a code from below for each [1] through [4].
(e.g. DLA1-2P1A4-K/Q)
Input CPU RUN indicator LED: Red LED turns ON when the
CPU operates normally.
• Specify the specification for option code /Q
(e.g. /C01)
INPUT SPECIFICATIONS
■ Analog Input: DC voltage, 16 points
Operational range: -1.5 – +11.5V DC
Commons: All negatives
[1] TRANSMISSION MEDIA
1: Twisted-pair cable
2: Fiber optics cable
■ Pulse Input: Dry contact, 16 points
Commons: All negatives
7: Twisted-pair – fiber optics (repeater incorporated)
Frequency range: 0 – 10 Hz
Pulse width requirement: 10 msec. min.
Scaling factor: 1
[2] ANALOG INPUT
Voltage
Sensing: Approx. 7.5 V DC @ 1 mA
ON/OFF level: ≤ 200 Ω for ON; ≥ 100 kΩ for OFF
Counter: 0 – 16383 (3FFF (16)); reset to zero with overflow
A4: 0 – 10 V DC(Input resistance 1 MΩ min.)
A5: 0 – 5 V DC(Input resistance 1 MΩ min.)
A6: 1 – 5 V DC (Input resistance 1 MΩ min.)
PERFORMANCE
Accuracy: ±10 mV
[3] POWER INPUT
AC Power
Temp. coefficient: ±1.5 mV/°C (±0.9 mV/°F)
Multi-transmission time: 48 msec.
Input read time: 300 msec. per 32 points
K: 85 – 132 V AC
(Operational voltage range 85 – 132 V, 47 – 66 Hz)
L: 170 – 264 V AC
(Operational voltage range 170 – 264 V, 47 – 66 Hz)
DC Power
CAUTION
S: 12 V DC
When the power supply of DLA1-xP1 is temporarily turned
off and turned ON again, totalized pulse output from DLA1-
xU1 may be increased.
(Operational voltage range 12 V ±10 %, ripple 10 %p-p max.)
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
EXTERNAL VIEW
[4] OPTIONS
Pulse Input
Indicator LED
blank: none
/Q: With options (specify the specification)
Input CPU
RUN Indicator
40-pin Connector
Terminal Block
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
Modular Jack
/C02: Polyurethane coating
/C03: Rubber coating
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 26/33
http://www.m-system.co.jp/
MODEL: DLA1
CONNECTION DIAGRAM
■ INPUT
Ai 1
1
Ai 2
2
Ai 3
3
Ai 4
4
Ai 5
5
Ai 6
6
Ai 7
7
Ai 8
8
Ai 9
9
Ai 10
Ai 11
Ai 12
Ai 13
Ai 14
Ai 15
Ai 16
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
Do not use.
COM1(–)
COM1(–)
Pi 1
Pi 2
Pi 3
Pi 4
COM2(–)
Pi 5
Pi 6
Pi 7
Pi 8
COM2(–)
Pi 9
Pi 10
Pi 11
Pi 12
COM2(–)
Pi 13
Pi 14
Pi 15
Pi 16
COM2(–)
40
–
+
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 27/33
http://www.m-system.co.jp/
MODEL: DLA1
ANALOG I/O UNIT
SPECIFICATIONS OF OPTION: Q
(Ai 16 + Ao 16 points)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
MODEL: DLA1–[1]R1[2][3]–[4][5]
/C03: Rubber coating
ORDERING INFORMATION
• Code number: DLA1–[1]R1[2][3]-[4][5]
Specify a code from below for each [1] through [5].
(e.g. DLA1-2R1A4B4-K/Q)
GENERAL SPECIFICATIONS
Connection:
I/O: 40-pin connector terminal; M3 screws
(torque 0.7 N·m)
• Specify the specification for option code /Q
(e.g. /C01)
Applicable wire size: 0.75 mm
2
Isolation: I/O to transmission to power
I/O CPU RUN indicator LED: Red LED turns ON when the CPU
operates normally.
[1] TRANSMISSION MEDIA
1: Twisted-pair cable
2: Fiber optics cable
INPUT SPECIFICATIONS
Input: DC voltage, 16 points
7: Twisted-pair – fiber optics (repeater incorporated)
Operational range: -1.5 – +11.5 V DC
Commons: All negatives
[2] INPUT
Voltage
A4: 0 – 10 V DC(Input resistance 1 MΩ min.)
A5: 0 – 5 V DC(Input resistance 1 MΩ min.)
A6: 1 – 5 V DC (Input resistance 1 MΩ min.)
OUTPUT SPECIFICATIONS
Output: DC voltage, 16 points
Operational range: -1.5 – +11.5 V DC
Commons: All negatives
[3] OUTPUT
Voltage
PERFORMANCE
Accuracy: ±10 mV
B4: 0 – 10 V DC (Load resistance 10 kΩ min.)
B5: 0 – 5 V DC (Load resistance 10 kΩ min.)
B6: 1 – 5 V DC (Load resistance 10 kΩ min.)
Temp. coefficient: ±1.5 mV/°C (±0.9 mV/°F)
Multi-transmission time: 24 msec.
Input read time: 300 msec. per 16 points
Output time: 200 msec. per 16 points
[4] POWER INPUT
AC Power
K: 85 – 132 V AC
EXTERNAL VIEW
(Operational voltage range 85 – 132 V, 47 – 66 Hz)
L: 170 – 264 V AC
I/O CPU
RUN Indicator
(Operational voltage range 170 – 264 V, 47 – 66 Hz)
DC Power
Modular Jack
40-pin Connector
Terminal Block
S: 12 V DC
(Operational voltage range 12 V ±10 %, ripple 10 %p-p max.)
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
[5] OPTIONS
blank: none
/Q: With options (specify the specification)
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 28/33
http://www.m-system.co.jp/
MODEL: DLA1
CONNECTION DIAGRAM
■ I/O
Ai 1
1
Ai 2
2
Ai 3
3
Ai 4
4
Ai 5
5
Ai 6
6
Ai 7
7
Ai 8
8
Ai 9
9
Ai 10
Ai 11
Ai 12
Ai 13
Ai 14
Ai 15
Ai 16
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Do not use.
COM(–)
COM(–)
Ao 1
Ao 2
Ao 3
Ao 4
Ao 5
Ao 6
Ao 7
Ao 8
Ao 9
Ao 10
Ao 11
Ao 12
Ao 13
Ao 14
Ao 15
Ao 16
Do not use.
COM(–)
COM(–)
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 29/33
http://www.m-system.co.jp/
MODEL: DLA1
ANALOG & CONTACT I/O UNIT
SPECIFICATIONS OF OPTION: Q
(Ai 8 + Ao 8 + Di 8 + Do 8 points; relay contact output)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
MODEL: DLA1–[1]S1[2][3]–[4][5]
/C03: Rubber coating
ORDERING INFORMATION
• Code number: DLA1–[1]S1[2][3]-[4][5]
Specify a code from below for each [1] through [5].
(e.g. DLA1-1S1A4B4-K/Q)
GENERAL SPECIFICATIONS
Connection:
I/O: 40-pin connector terminal; M3 screws
(torque 0.7 N·m)
• Specify the specification for option code /Q
(e.g. /C01)
Applicable wire size: 0.75 mm
2
Isolation: I/O to transmission to power
Contact I/O indicator LED: Red LEDs turn on when the
respective I/O channels are ON.
[1] TRANSMISSION MEDIA
1: Twisted-pair cable
I/O CPU RUN indicator LED: Red LED turns ON when the CPU
operates normally.
2: Fiber optics cable
7: Twisted-pair – fiber optics (repeater incorporated)
INPUT SPECIFICATIONS
■ Analog Input: DC voltage, 8 points
Operational range: -1.5 – +11.5 V DC
Commons: All negatives
[2] ANALOG INPUT
Voltage
A4: 0 – 10 V DC(Input resistance 1 MΩ min.)
A5: 0 – 5 V DC(Input resistance 1 MΩ min.)
A6: 1 – 5 V DC (Input resistance 1 MΩ min.)
■ Contact Input: Dry contact, 8 points
Commons: All negatives
Sensing: Approx. 15 V DC @ 3 mA
ON/OFF level: ≤ 200 Ω for ON; ≥ 100 kΩ for OFF
[3] ANALOG OUTPUT
Voltage
B4: 0 – 10 V DC (Load resistance 10 kΩ min.)
B5: 0 – 5 V DC (Load resistance 10 kΩ min.)
B6: 1 – 5 V DC (Load resistance 10 kΩ min.)
OUTPUT SPECIFICATIONS
■ ANALOG OUTPUT: DC voltage, 8 points
Operational range: -1.5 – +11.5 V DC
Commons: All negatives
■ CONTACT OUTPUT: Relay contact, 8 points
Commons: Per 4 points; common current 4A max.
Contact rating: 120 V AC @ 1 A (cos ø = 1)
30 V DC @ 1 A (resistive load)
[4] POWER INPUT
AC Power
K: 85 – 132 V AC
(Operational voltage range 85 – 132 V, 47 – 66 Hz)
L: 170 – 264 V AC
Maximum switching voltage: 120 V AC or 30 V DC
Maximum switching power: 120 VA or 30 W
Minimum load: 5 V DC @ 10 mA
(Operational voltage range 170 – 264 V, 47 – 66 Hz)
DC Power
Mechanical life: 5 × 10 cycles
7
S: 12 V DC
For maximum relay life with inductive loads, external
protection is recommended.
(Operational voltage range 12 V ±10 %, ripple 10 %p-p max.)
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
[5] OPTIONS
blank: none
/Q: With options (specify the specification)
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 30/33
http://www.m-system.co.jp/
MODEL: DLA1
PERFORMANCE
Accuracy: ±10 mV
Temp. coefficient: ±1.5 mV/°C (±0.9 mV/°F)
Multi-transmission time: 12 msec.
Input read time
Analog: 300 msec. per 8 points
Contact: 3 msec. per 8 points
Output time
Analog: 200 msec. per 8 points
Contact: 8 msec. per 8 points for OFF to ON
3 msec. per 8 points for ON to OFF
EXTERNAL VIEW
Contact I/O
Indicator LED
I/O CPU
RUN Indicator
40-pin Connector
Terminal Block
Modular Jack
CONNECTION DIAGRAM
■ I/O
Ai 1
1
Ai 2
2
Ai 3
3
Ai 4
4
Ai 5
5
Ai 6
6
Ai 7
7
Ai 8
8
COM1(–)
COM1(–)
Ao 1
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Ao 2
Ao 3
Ao 4
Ao 5
Ao 6
Ao 7
Ao 8
COM1(–)
COM1(–)
Di 1
Di 2
Di 3
Di 4
Di 5
Di 6
Di 7
Di 8
+
–
COM1(–)
COM1(–)
Do 1
Do 2
Do 3
Do 4
COM2(–)
Do 5
Do 6
Do 7
Do 8
COM3(–)
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 31/33
http://www.m-system.co.jp/
MODEL: DLA1
PULSE & ANALOG OUTPUT UNIT
GENERAL SPECIFICATIONS
(Po 16 + Ao 16 points)
Connection
Output: 40-pin connector terminal; M3 screws
(torque 0.7 N·m)
MODEL: DLA1–[1]U1[2]–[3][4]
Applicable wire size: 0.75 mm
2
Isolation: Output to transmission to power
Pulse output indicator LED: Red LEDs turn on when the
respective output channels are closed.
ORDERING INFORMATION
• Code number: DLA1–[1]U1[2]-[3][4]
Specify a code from below for each [1] through [4].
(e.g. DLA1-2U1B4-K/Q)
Output CPU RUN indicator LED: Red LED turns ON when the
CPU operates normally.
• Specify the specification for option code /Q
(e.g. /C01)
OUTPUT SPECIFICATIONS
■ Analog Output: DC voltage, 16 points
Operational range: -1.5 – +11.5 V DC
Commons: All negatives
Use Ordering Information Sheet (No. ESU-6510-U1)
to describe your system configuration in order to calculate
appropriate “Loss of Communication Check Time.”
■ Pulse Output: Open collector (Darlington), 16 points
Commons: All negatives
[1] TRANSMISSION MEDIA
1: Twisted-pair cable
Contact rating: 30 V DC @ 100 mA (resistive load)
Saturation voltage: 1.6 V DC
2: Fiber optics cable
7: Twisted-pair – fiber optics (repeater incorporated)
Maximum frequency: 10 Hz
Pulse width: Duty ratio 50 %
[2] ANALOG OUTPUT
Voltage
PERFORMANCE
B4: 0 – 10 V DC (Load resistance 10 kΩ min.)
B5: 0 – 5 V DC (Load resistance 10 kΩ min.)
B6: 1 – 5 V DC (Load resistance 10 kΩ min.)
Accuracy: ±10 mV
Temp. coefficient: ±1.5 mV/°C (±0.9 mV/°F)
Multi-transmission time: 48 msec.
Output time: 200 msec. per 32 points
[3] POWER INPUT
AC Power
EXTERNAL VIEW
K: 85 – 132 V AC
Pulse Output
Indicator LED
(Operational voltage range 85 – 132 V, 47 – 66 Hz)
L: 170 – 264 V AC
Output CPU
RUN Indicator
(Operational voltage range 170 – 264 V, 47 – 66 Hz)
DC Power
40-pin Connector
Terminal Block
S: 12 V DC
Modular Jack
(Operational voltage range 12 V ±10 %, ripple 10 %p-p max.)
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
[4] OPTIONS
blank: none
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 32/33
http://www.m-system.co.jp/
MODEL: DLA1
CONNECTION DIAGRAM
■ OUTPUT
Ao 1
1
Ao 2
2
Ao 3
3
Ao 4
4
Ao 5
5
Ao 6
6
Ao 7
7
Ao 8
8
Ao 9
9
Ao 10
Ao 11
Ao 12
Ao 13
Ao 14
Ao 15
Ao 16
COM1(–)
COM1(–)
COM1(–)
COM1(–)
Po 1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Po 2
Po 3
Po 4
Po 5
Po 6
Po 7
Po 8
CLAMP1
COM2(–)
Po 9
Po 10
Po 11
Po 12
Po 13
Po 14
Po 15
Po 16
CLAMP2
COM2(–)
Specifications are subject to change without notice.
DLA1 SPECIFICATIONS
ES-6510 Rev.9 Page 33/33
http://www.m-system.co.jp/
相关型号:
©2020 ICPDF网 联系我们和版权申明