ATG-5141-V 概述
Limit Alarms (potentiometer adj.) A-UNIT
ATG-5141-V 数据手册
通过下载ATG-5141-V数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载MODEL: B3FP
Space-saving Two-wire Signal
Conditioners B3-UNIT
[1] OPTIONS (multiple selections)
Standards & Approvals
blank: CE marking
/UL: UL approval, CE marking
Other Options
FREQUENCY TRANSMITTER
(field-configurable)
blank: none
Functions & Features
/Q: Option other than the above (specify the specification)
• Converts the output from a pulse-type transducer
into a 4 – 20 mA DC signal
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
• DIP switch configurable input range
• Monitor terminals
• High-density mounting
/C02: Polyurethane coating
/C03: Rubber coating (UL not available)
18 (.71)
GENERAL SPECIFICATIONS
Construction: Small-sized front terminal structure
Connection: Euro type connector terminal
106
(4.17)
(applicable wire size: 0.2 to 2.5 mm , stripped length 8 mm)
2
Housing material: Flame-resistant resin (gray)
Isolation: Input to output
DIP/rotary switches: For input calibration
(Refer to the instruction manual)
110.5
(4.35)
mm (inch)
Noise filter: Chattering protection filter selectable with DIP
switches (time constant 1 msec.)
Pulse sensing: DC coupled or capacitor coupled selectable
with DIP SW
MODEL: B3FP[1]
ORDERING INFORMATION
• Code number: B3FP[1]
INPUT SPECIFICATIONS
Measurable frequencies: 0 – 0.01 Hz through 100 kHz; Sine
waves with frequencies lower than 0.1 Hz cannot be
detected with capacitor coupling.
Specify a code from below for [1].
(e.g. B3FP/UL/Q)
• Specify the specification for option code /Q
(e.g. /C01)
Pulse width time requirement: Min. 4 μsec. for both H and L
levels
DC offset: Selectable within the maximum voltage for
respective pulse amplitude setting.
• Orders will be shipped with default factory settings as
shown below.
(e.g. For the amplitude 2 Vp-p with the maximum voltage
10 V, DC offset can be as low as -9 V and as high as +9 V.)
Frequency offset: Selectable up to 50 % of the full-scale
frequency.
• Factory default setting:
Input type: Voltage pulse
Frequency range: 0 – 1000 Hz
Pulse amplitude: 5 Vp-p
DC offset: 2.5 V
■ Open Collector
Sensing voltage/current: Approx. 2.5 V DC @ 1mA
Detecting levels: ≤ 750 Ω / 0.7 V for ON;
≥ 3.0 kΩ / 1.3 V for OFF
Pulse sensing: DC coupled
Noise filter: None
Detecting level: High (2 V)
■ Voltage Pulse
Waveform: Square or sine
Input impedance: 10 kΩ min.
INPUT – Field-selectable
Open collector
Input amplitude: Min. 0.1 V p-p, max. 200 Vp-p
Max. voltage between input terminals: 100 V
(Max. voltage across the input terminals: 70 V for conform
with EU Directive; 30 V rms, 42.4 V peak or 60 V DC for UL
approval)
Voltage pulse
Two-wire current pulse
B3FP SPECIFICATIONS
ES-7516 Rev.9 Page 1/4
https://www.m-system.co.jp/
MODEL: B3FP
Detecting level: See the table below
■ Two-wire Current Pulse
Max. 55°C (131°F) for UL approval
Operating humidity: 0 to 95 %RH (non-condensing)
Mounting: DIN rail
Input resistance: Receiving resistor 200 Ω
Input range: 0 – 25 mA
Weight: 80 g (2.8 oz)
Detecting level: See the table below
(Convert current into voltage using the receiving resistor
value.)
PERFORMANCE in percentage of span
Accuracy: ±0.1 % (±0.3 % for frequencies below 10 Hz for
sine waves detected with capacitor coupling)
Temp. coefficient: ±0.02 %/°C (±0.01 %/°F)
Response time: Max. 0.5 sec. + 1 pulse cycle (0 – 90 %)
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute
PULSE AMPLITUDE
DETECTING LEVEL
0.1 – 2 Vp-p 2 – 10 Vp-p 10 – 200 Vp-p
Zero-cross
Low level
0V
45mV
200mV
1V
0V
60mV
0V
300mV
2V
Middle level
High level
400mV
2V
10V
(input to output to ground)
DETECTING LEVEL
Zero-cross
DEADBAND
15ꢀ of Amplitude, ≥45mV*
15ꢀ of Amplitude, ≥40mV*
15ꢀ of Amplitude, ≥80mV*
40ꢀ of Detecting Level
STANDARDS & APPROVALS
EU conformity:
Low level
Middle level
High level
EMC Directive
EMI EN 61000-6-4
*Minimum deadband required for the amplitude 0.1 – 2 Vp-p.
EMS EN 61000-6-2
■ VOLTAGE PULSE WAVEFORM
RoHS Directive
Volts
100V max.
Approval:
VH
VL
UL/C-UL general safety requirements
(UL 61010-1, CAN/CSA-C22.2 No.1010-1)
Amplitude
Vinp-p
DC Offset Detecting Level
t
OUTPUT SPECIFICATIONS
Output: 4 – 20 mA DC
Load resistance vs. supply voltage:
Load Resistance (Ω) = (Supply Voltage (V) – 12 (V)) ÷ 0.02
(A) (including leadwire resistance)
1650
1600
1400
1200
1000
800
600
400
200
0
1012
20
30
40 45
SUPPLY VOLTAGE [V ]
(600Ω maximum at 24V DC)
INSTALLATION
Supply voltage: 12 – 45 V DC
Operating temperature:
-40 to +85°C (-40 to +185°F)
B3FP SPECIFICATIONS
ES-7516 Rev.9 Page 2/4
https://www.m-system.co.jp/
MODEL: B3FP
EXTERNAL VIEW
FRONT VIEW
SIDE VIEW
High-order Digit (0 – 9)
Low-order Digit (0 – 9)
Configuration Rotary SW
10 11 12
0
5
Zero Adj.
Span Adj.
SW1 SW2
SW3
1 2 3 4 5 6 7 8
SW4
4
5
6
Configuration DIP SW
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm [inch]
10 11 12
DIN RAIL
35mm wide
4
5
6
18 (.71)
110.5 (4.35)
[5 (.20)]
• When mounting, no extra space is needed between units.
B3FP SPECIFICATIONS
ES-7516 Rev.9 Page 3/4
https://www.m-system.co.jp/
MODEL: B3FP
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
FREQUENCY SW
Z
S
Isolation
MONITOR
Waveform
Shaper
Digital
Computation
Voltage
Amplifier
Output
Driver
+
–
4
5
6
12
10
11
–
+
–
mA
*
INPUT
24 V DC
INPUT RANGE
SELECTOR DIP SW
LOAD
OUTPUT
4 – 20 mA DC
*Input shunt resistor incorporated for two-wire current pulse input.
Input Connection Examples
■ Open Collector
■ Two-wire Current Pulse
• External DC Supply
2.5 V
2.4 kΩ
200 Ω
+
–
4
5
–
+
4
5
2-WIRE
PICK-UP
DC SUPPLY
+
–
■ Voltage Pulse
+
–
4
5
Specifications are subject to change without notice.
B3FP SPECIFICATIONS
ES-7516 Rev.9 Page 4/4
https://www.m-system.co.jp/
ATG-5141-V 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
ATG-5141-V/Q | MSYSTEM | Limit Alarms (potentiometer adj.) A-UNIT | 获取价格 | |
ATG-5142-B | MSYSTEM | Limit Alarms (potentiometer adj.) A-UNIT | 获取价格 | |
ATG-5142-B/Q | MSYSTEM | Limit Alarms (potentiometer adj.) A-UNIT | 获取价格 | |
ATG-5142-C | MSYSTEM | Limit Alarms (potentiometer adj.) A-UNIT | 获取价格 | |
ATG-5142-C/Q | MSYSTEM | Limit Alarms (potentiometer adj.) A-UNIT | 获取价格 | |
ATG-5142-P | MSYSTEM | Limit Alarms (potentiometer adj.) A-UNIT | 获取价格 | |
ATG-5142-P/Q | MSYSTEM | Limit Alarms (potentiometer adj.) A-UNIT | 获取价格 | |
ATG-5142-R | MSYSTEM | Limit Alarms (potentiometer adj.) A-UNIT | 获取价格 | |
ATG-5142-R/Q | MSYSTEM | Limit Alarms (potentiometer adj.) A-UNIT | 获取价格 | |
ATG-5142-S | MSYSTEM | Limit Alarms (potentiometer adj.) A-UNIT | 获取价格 |
ATG-5141-V 相关文章
- 2024-09-20
- 5
- 2024-09-20
- 9
- 2024-09-20
- 8
- 2024-09-20
- 6