ANR-223-R [MSYSTEM]
Limit Alarms (potentiometer adj.) A-UNIT;型号: | ANR-223-R |
厂家: | M-SYSTEM |
描述: | Limit Alarms (potentiometer adj.) A-UNIT |
文件: | 总4页 (文件大小:124K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MODEL: ANR
3: Lo (coil energized at alarm)
Limit Alarms (potentiometer adj.) A-UNIT
4: Lo (coil de-energized at alarm)
ANGLE SENSOR ALARM
Functions & Features
[4] POWER INPUT
AC Power
• Providing SPDT relay outputs at preset voltage level
provided from Angle Sensor (model: NRA)
• Dual (Hi/Lo) trip
B: 100 V AC
C: 110 V AC
D: 115 V AC
F: 120 V AC
G: 200 V AC
H: 220 V AC
J: 240 V AC
• Energized or de-energized coil at a tripped condition
selectable
• 50 % zero/span adjustments
• Hysteresis (deadband) adjustable
• Enclosed relays
DC Power
• Relays can be powered 110 V DC
• High-density mounting
S: 12 V DC
R: 24 V DC
V: 48 V DC
Typical Applications
• Annunciator
P: 110 V DC
• Various alarm applications
RELATED PRODUCTS
• Brushless angle sensor (model: NRA)
50
(1.97)
GENERAL SPECIFICATIONS
Construction: Plug-in
80
(3.15)
Connection: M3.5 screw terminals
Housing material: Flame-resistant resin (black)
Isolation: Input to output 1 to output 2 to power
Zero adjustment: 0 – 50 % of linearity-assured range of the
angle sensor (front)
136
(5.35)
mm (inch)
Span adjustment: 50 – 100 % of linearity-assured range of
the angle sensor (front)
MODEL: ANR-[1]1[2][3]-[4]
Setpoint adjustments: 270°-turn screwdriver adjustments
(front); 0 – 100 % independently
ORDERING INFORMATION
• Code number: ANR-[1]1[2][3]-[4]
Specify a code from below for each of [1] through [4].
(e.g. ANR-1111-B)
Hysteresis (deadband) adjustments: 1 – 100 % (front)
LEDs: LED turns on at a tripped condition; red for output 1,
green for output 2 (located behind the front cover)
Power ON timer: Relays de-energized for approx. 2 seconds
after power is turned on.
[1] ACTION
1: Direct (output increases with input increase)
INPUT SPECIFICATIONS
Input: 2 – 3 V DC (output from Angle Sensor)
Excitation: 5 V DC ±2 %
2: Reverse (output increases with input decrease)
[2] SETPOINT 1 OUTPUT
1: Hi (coil energized at alarm)
2: Hi (coil de-energized at alarm)
3: Lo (coil energized at alarm)
4: Lo (coil de-energized at alarm)
[3] SETPOINT 2 OUTPUT
1: Hi (coil energized at alarm)
2: Hi (coil de-energized at alarm)
ANR SPECIFICATIONS
ES-2116 Rev.2 Page 1/4
http://www.m-system.co.jp/
MODEL: ANR
OUTPUT SPECIFICATIONS
■ Relay Contact: 100 V AC @ 1 A (cos ø = 1)
120 V AC @ 1 A (cos ø = 1)
240 V AC @ 0.5 A (cos ø = 1)
30 V DC @ 1 A (resistive load)
Maximum switching voltage: 380 V AC or 125 V DC
Maximum switching power: 120 VA or 30 W
Minimum load: 5 V DC @ 10 mA
Mechanical life: 5 x 10 cycles
7
For maximum relay life with inductive loads, external
protection is recommended.
Alarm Trip Operation Terminal No. in parentheses
(9-11)ON
Output 1
(9-10)ON
(1-3)ON
Output 2
(1-2)ON
Input
(%)
0
▲
50
▲
100
Output 2
Setpoint
Output 1
Setpoint
Trip Operation in Power Failure
• Output Code: 1 & 4: Terminals 1 – 2, 9 – 10 turn ON
• Output Code: 2 & 3: Terminals 1 – 3, 9 – 11 turn ON
INSTALLATION
Power input
• AC: Operational voltage range: rating ±10 %,
50/60 ±2 Hz, approx. 2 VA
• DC: Operational voltage range: rating ±10 %, or 85 – 150
V for 110 V rating (ripple 10 % p-p max.)
approx. 2 W (80 mA at 24 V)
Operating temperature: -5 to +60°C (23 to 140°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Surface or DIN rail
Weight: 450 g (0.99 lb)
PERFORMANCE in percentage of span
Trip point repeatability: ±0.5 %
Temp. coefficient: ±0.05 %/°C (±0.03 %/°F)
Response time: Approx. 0.5 sec. (0 – 100 % at 90 %
setpoint)
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (input to output 1
to output 2 to power to ground)
ANR SPECIFICATIONS
ES-2116 Rev.2 Page 2/4
http://www.m-system.co.jp/
MODEL: ANR
EXTERNAL VIEW
Input Monitor
Span Adj.
Zero Adj.
No.1 Setpoint Adj.
No.1 LED
No.1 Hysteresis (Deadband) Adj.
No.2 Hysteresis (Deadband) Adj.
No.2 LED
No.2 Setpoint Adj.
Front Cover (open)
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
CLAMP
(top & bottom)
7.8 (.31)
DIN RAIL
35mm wide
8
7
6
5
4
2–
4.5 (.18) dia.
MTG HOLE
25 (.98) deep
9
3
2
10 11
1
11
–M3.5
SCREW
50 (1.97)
107 (4.21)
136 (5.35)
40 (1.57)
50 (1.97)
[3.3 (.13)]
• When mounting, no extra space is needed between units.
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
■ Relay Protection
• AC Powered
SETPOINT
MONITOR
HYSTERESIS
(DEADBAND)
Inductive
Load (Coil)
red
EXC
INP
*
4
5
6
Z
S
11
10
9
H
Varistor or Spark
Quenching Circuit
yellow
ANGLE
SENSOR
LOAD
Low Drift
Amplifier
Ry
Comparator
SETPOINT 1
OUTPUT
L
white COM
U
• DC Powered
C
Inductive
Load (Coil)
Exc. Volt.
Generator
*
3
H
Diode, Varistor or
CR Circuit
Ry
Comparator
SETPOINT 2
OUTPUT
LOAD
2
L
1
C
SETPOINT HYSTERESIS
(DEADBAND)
7
U(+)
V(–)
POWER
8
Base Socket
*Relay status for output codes “1” & “4”, at power OFF.
ANR SPECIFICATIONS
ES-2116 Rev.2 Page 3/4
http://www.m-system.co.jp/
MODEL: ANR
Specifications are subject to change without notice.
ANR SPECIFICATIONS
ES-2116 Rev.2 Page 4/4
http://www.m-system.co.jp/
相关型号:
©2020 ICPDF网 联系我们和版权申明