10FNS-H36-R/C02 [MSYSTEM]
High-density Signal Conditioners 10-RACK;型号: | 10FNS-H36-R/C02 |
厂家: | M-SYSTEM |
描述: | High-density Signal Conditioners 10-RACK |
文件: | 总3页 (文件大小:94K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MODEL: 10FNS
5: 0 – 5 V DC (Load resistance 500 Ω min.)
High-density Signal Conditioners 10-RACK
6: 1 – 5 V DC (Load resistance 500 Ω min.)
SQUARE ROOT EXTRACTOR
Functions & Features
[3] OUTPUT 2
0: None
• Providing two DC outputs proportional to the root of the
input signal
Voltage
6: 1 – 5 V DC (Load resistance 5000 Ω min.)
• Low-end cutout
• Optional second channel output available at the front
terminals and at the Standard Rack connector
POWER INPUT
DC Power
Typical Applications
R: 24 V DC
• Converting differential pressure to flow
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
[4] OPTIONS
blank: none
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
GENERAL SPECIFICATIONS
Construction: Rack-mounted; terminal access via screw
terminals at the front and via card-edge connector at the
rear; terminal cover provided
MODEL: 10FNS–[1][2][3]–R[4]
ORDERING INFORMATION
• Code number: 10FNS-[1][2][3]-R[4]
Specify a code from below for each [1] through [4].
(e.g. 10FNS-6A6-R/Q)
Connection
Input: M3.5 screw terminals (torque 0.8 N·m)
Output: Card-edge connector and M3.5 screw terminals
(torque 0.8 N·m)
• Specify the specification for option code /Q
(e.g. /C01)
Power input: Supplied from card-edge connector
Screw terminal: Nickel-plated steel
Housing material: Flame-resistant resin (black)
Isolation: Input to output 1 to output 2 to power
Overrange output: Approx. 0 to 120 % at 1 – 5V
Zero adjustment: -2 to +2 % (front)
[1] INPUT
Current
A: 4 – 20 mA DC (Input resistance 87.7 Ω)
H: 10 – 50 mA DC (Input resistance 100 Ω)
Voltage
Span adjustment: 95 to 105 % (front)
Low-end cutout: Approx. 10 % (output); curve
characteristics shown in the figure below
6: 1 – 5 V DC (Input resistance 1 MΩ min.)
[2] OUTPUT 1
Current
A: 4 – 20 mA DC (Load resistance 600 Ω max.)
D: 0 – 20 mA DC (Load resistance 600 Ω max.)
G: 0 – 1 mA DC (Load resistance 12 kΩ max.)
Voltage
10%
6%
0
1% INPUT
3: 0 – 1 V DC (Load resistance 100 Ω min.)
4: 0 – 10 V DC (Load resistance 1000 Ω min.)
http://www.m-system.co.jp/
10FNS SPECIFICATIONS
ES-0845 Rev.7 Page 1/3
MODEL: 10FNS
INPUT SPECIFICATIONS
■ DC Current: Input resistor incorporated
OUTPUT SPECIFICATIONS
The output turns to 0 % when the input is open.
INSTALLATION
Current consumption: Approx. 30 mA with voltage output 1
Approx. 55 mA with current output 1
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Standard Rack 10BXx
Weight: 200 g (0.44 lb)
PERFORMANCE in percentage of span
Accuracy: ±0.25 % (input 1 – 100 %)
Temp. coefficient: ±0.03 %/°C (±0.02 %/°F)
Response time: ≤ 0.5 sec. (0 – 90 %)
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 500 V AC @ 1 minute
(input to output 1 to output 2 to power)
1500 V AC @ 1 minute (input or output or power to ground)
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
7–M3.5 SCREW
8 (.31)
2–4.3 (.17) dia.
MTG HOLE
TERMINAL COVER
1
5
2
6
3
7
8
3 (.12)
25 (.98)
51 (2.01)
130 (5.12)
http://www.m-system.co.jp/
10FNS SPECIFICATIONS
ES-0845 Rev.7 Page 2/3
MODEL: 10FNS
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
S
Z
Isolation
Sq. Root
Extractor
Output
Driver
+
–
1
2
3
7
8
+
–
*
INPUT
OUTPUT 1
OUTPUT 2
Z
S
Output
Driver
5
6
+
–
OUTPUT 2**
POWER
* Input shunt resistor incorporated for current input.
**1 output type has the output 1 connected to the card-edge connector in parallel.
Remark 1) The section enclosed by broken line is only for 2nd output channel.
Specifications are subject to change without notice.
http://www.m-system.co.jp/
10FNS SPECIFICATIONS
ES-0845 Rev.7 Page 3/3
相关型号:
©2020 ICPDF网 联系我们和版权申明