10AP-450-R/C03 [MSYSTEM]
High-density Signal Conditioners 10-RACK;型号: | 10AP-450-R/C03 |
厂家: | M-SYSTEM |
描述: | High-density Signal Conditioners 10-RACK |
文件: | 总3页 (文件大小:116K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MODEL: 10AP
High-density Signal Conditioners 10-RACK
[2] OUTPUT 1
1: Open collector (max. 1 kHz)
2: 5 V pulse (max. 1 kHz)
DC/FREQUENCY CONVERTER
Functions & Features
5: Photo MOSFET relay pulse (max. 30 Hz)
• Providing two pulse rate outputs in proportion to DC input
signal
[3] OUTPUT 2
0: None
Typical Applications
1: Open collector
• Totalizing applications in combination with a counter
POWER INPUT
DC Power
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
[4] OPTIONS
blank: none
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
MODEL: 10AP–[1][2][3]–R[4]
GENERAL SPECIFICATIONS
Construction: Rack-mounted; terminal access via screw
terminals at the front and via card-edge connector at the
rear; terminal cover provided
ORDERING INFORMATION
• Code number: 10AP-[1][2][3]-R[4]
Specify a code from below for each of [1] through [4].
(e.g. 10AP-621-R/Q)
Connection
• Special input range (For codes Z & 0)
• Output frequency range (e.g. 0 – 500 Hz)
Frequencies of Output 1 and 2 are the same.
• Specify the specification for option code /Q
(e.g. /C01)
Input: M3.5 screw terminals (torque 0.8 N·m)
Output: Card-edge connector and M3.5 screw terminals
(torque 0.8 N·m)
Power input: Supplied from card-edge connector
Screw terminal: Nickel-plated steel
Housing material: Flame-resistant resin (black)
Isolation: Input to output 1 to output 2 to power
Overrange output: Approx. 0 to 120 %
Zero adjustment: 0 – 5 % (front)
[1] INPUT
Current
A: 4 – 20 mA DC (Input resistance 250 Ω)
D: 0 – 20 mA DC (Input resistance 50 Ω)
G: 0 – 1 mA DC (Input resistance 1000 Ω)
H: 10 – 50 mA DC (Input resistance 100 Ω)
Z: Specify current (See INPUT SPECIFICATIONS)
( 0 % input must be 0 mA.)
Span adjustment: 95 to 105 % (front)
INPUT SPECIFICATIONS
■ DC Current: Input resistor incorporated
Specify input resistance value for code Z.
Voltage
(R ≤ 2 W ÷ [F.S. Current] )
2
3: 0 – 1 V DC (Input resistance 1 MΩ min.)
4: 0 – 10 V DC (Input resistance 1 MΩ min.)
5: 0 – 5 V DC (Input resistance 1 MΩ min.)
6: 1 – 5 V DC (Input resistance 1 MΩ min.)
0: Specify voltage (See INPUT SPECIFICATIONS)
( 0 % input must be 0 V.)
■ DC Voltage: 0 – 300V DC
Minimum span: 1V
Input resistance: 1 MΩ min.
10AP SPECIFICATIONS
ES-0851 Rev.9 Page 1/3
http://www.m-system.co.jp/
MODEL: 10AP
OUTPUT SPECIFICATIONS
■ Open Collector: 30 V DC @ 100 mA (resistive load)
Frequency range: 0 – 10 pulses/hour through 1 kHz
Saturation voltage: 0.6 V DC
INSTALLATION
Current consumption: Approx. 60 mA
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Standard Rack 10BXx
When output 1 is photo MOSFET relay pulse, a timer for
output 2 is provided, which limits ON time within 75
±25msec.
Weight: 200 g (0.44 lb)
■ 5 V Pulse
PERFORMANCE in percentage of span
Accuracy: ±0.1 %
Frequency range: 0 – 10 pulses/hour through 1 kHz
Hi level: 3.0 – 5.5 V
Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)
Response time: Approx. 3 sec. (0 – 90 %)
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 500 V AC @ 1 minute
(input to output 1 to output 2 to power)
Lo level: ≤ 0.5 V
Load resistance: 250 Ω min.
■ Photo MOSFET Relay Pulse
Frequency range: 0 – 10 pulses/hour through 30 Hz
Timer: Limits ON time within 75 ±25 msec.
Rating: 132 V AC @ 200 mA (cos ø = 1)
30 V DC @ 200 mA (resistive load)
ON resistance: ≤ 2 Ω
1500 V AC @ 1 minute (input or output or power to ground)
OUTPUT PULSE WIDTH
■ Frequency less than 500 Hz at 100% input
➞ Duty ratio 20% (See the figure below)
• Open Collector
• Voltage Pulse
OFF
H Level
ON
L Level
20
%
20%
80%
80%
1 / f
1 / f
■ Frequency greater than 500 Hz at 100% input
➞ See the figure and equation below.
• Open Collector
• Voltage Pulse
OFF
H Level
ON
L Level
Pulse Width
Pulse Width
1
Pulse Width [millisec.] =
2.09 × 100% Frequency [kHz]
■ When OUTPUT 1 is Photo MOSFET Relay Pulse
➞ See the figure below. ON pulse width is limited
within 75 25 msec. when the output frequency
gets low (below 2 to 4 Hz).
• OUTPUT 2’s Open Collector and Photo MOSFET
Relay Pulse
OFF
ON
20
%
80
%
1 / f
10AP SPECIFICATIONS
ES-0851 Rev.9 Page 2/3
http://www.m-system.co.jp/
MODEL: 10AP
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
7–M3.5 SCREW
8 (.31)
2–4.3 (.17) dia.
MTG HOLE
TERMINAL COVER
1
5
2
6
3
7
8
3 (.12)
25 (.98)
51 (2.01)
130 (5.12)
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
Z
S
Isolation
**
Timer
Low Drift
Amplifier
Voltage to
Frequency
Output
Driver
+
–
1
2
3
7
8
5
6
+
–
+
–
Divider
*
INPUT
OUTPUT 1
OUTPUT 2
Output
Driver
OUTPUT 2***
POWER
*
Input shunt resistor incorporated for current input.
** Photo MOSFET relay pulse only.
***
For 1 output channel type, OUTPUT 1 is also connected to the card-edge connector inside.
Note: The section enclosed by broken line is only for 2nd output channel.
Output Connection Examples
■ Open Collector
■ Voltage Pulse
■ Photo MOSFET Relay Pulse
• AC Powered
Relay or
Counter Coil
7
8
+
–
+
–
7
8
+
–
+
–
7
8
Varistor or Spark
Quenching Circuit
LOAD
U
• DC Powered
Relay or
Counter Coil
7
8
Spark Quenching
Diode
LOAD
Specifications are subject to change without notice.
10AP SPECIFICATIONS
ES-0851 Rev.9 Page 3/3
http://www.m-system.co.jp/
相关型号:
©2020 ICPDF网 联系我们和版权申明