MP1523DT [MPS]

6 White LEDs, 20mA Precision WLED Driver Evaluation Board; 6个白光LED , 20毫安精密WLED驱动器评估板
MP1523DT
型号: MP1523DT
厂家: MONOLITHIC POWER SYSTEMS    MONOLITHIC POWER SYSTEMS
描述:

6 White LEDs, 20mA Precision WLED Driver Evaluation Board
6个白光LED , 20毫安精密WLED驱动器评估板

显示驱动器 驱动程序和接口 接口集成电路 光电二极管
文件: 总4页 (文件大小:124K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
TM  
EV0035  
6 White LEDs, 20mA Precision  
WLED Driver Evaluation Board  
TM  
The Future of Analog IC Technology  
DESCRIPTION  
FEATURES  
The EV0035 is the evaluation board for the  
MP1523, which is designed for driving up to six  
(6) series WLEDs from a single cell Lithium Ion  
battery. The board is set up to obtain 20mA  
LED current. The current can be adjusted by  
varying the resistor R2.  
2.7V to 25V Input Voltage Range  
Drives up to 6 Series White LEDs  
Surface-Mount Components  
Fully Assembled and Tested  
APPLICATIONS  
Cell Phones  
The MP1523 uses current limited, variable  
frequency architecture to regulate the LED  
current while maintaining high efficiency. The  
BIAS pin measures the output voltage and turns  
off the converter if an over voltage condition is  
present to prevent damage due to an open  
circuit condition. The LED current is measured  
with an external current sense resistor. The low  
0.4V full-scale regulation threshold and 0.5  
power switch minimize power loss to improve  
efficiency.  
Handheld Computers and PDAs  
Digital Still and Video Cameras  
Small LCD Displays  
“MPS” and “The Future of Analog IC Technology” are Trademarks of Monolithic  
Power Systems, Inc.  
ELECTRICAL SPECIFICATIONS  
Parameter  
Symbol  
Value  
2.7 – 25  
up to 6  
20  
Units  
Input Voltage  
# of WLEDs  
LED Current  
VIN  
V
ILED  
mA  
EV0035 EVALUATION BOARD  
Efficiency vs V  
IN  
85  
80  
75  
70  
(L x W x H) 2.0” x 1.4” x 0.5”  
(5.0cm x 3.5 x 1.2cm)  
2.5  
3.0  
3.5  
(V)  
4.0  
4.5  
Board Number  
MPS IC Number  
MP1523DT  
V
IN  
EV0035_AC01  
EV0035  
EV0035 Rev. 1.2  
3/30/2006  
www.MonolithicPower.com  
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.  
© 2006 MPS. All Rights Reserved.  
1
TM  
EV0035 – 6 WHITE LEDs, 20mA PRECISION WLED DRIVER EVALUATION BOARD  
EVALUATION BOARD SCHEMATIC  
D1  
MBR0540  
VCC  
GND  
LED1  
LED2  
LED3  
LED4  
LED5  
LED6  
U1  
4
1
5
3
EN  
EN  
SW  
J1  
MP1523  
GND  
BIAS  
C3  
10nF  
2
GND  
FB  
EV0035_S01  
EV0035 BILL OF MATERIALS  
Qty  
2
Ref  
C1, C2  
C3  
Value Description  
1µF Ceramic Cap., 50V, X7R  
10nF Ceramic Cap., 50V, X7R  
Package Manufacturer Part Number  
1206  
0603  
TDK  
TDK  
C3216X7R1H105K  
C1608X7R1H103K  
1
ON  
1
6
D1  
Diode Schottky, 40V, 500mA SOD-123  
Not Stuffed  
MBR0540T1  
Semiconductor  
LED1 to  
LED6  
1
1
1
1
L1  
R1  
R2  
U1  
15µH Inductor, 450mA  
100kFilm Res., 5%  
SMD  
0603  
0603  
Sumida  
CDRH3D16-150NC  
ERJ-3GEYJ104V  
ERJ-3GEYJ200V  
MP1523DT  
Panasonic  
Panasonic  
20Ω  
Film Res., 5%  
White LED Driver  
SOT23-5 MPS  
EV0035 Rev. 1.2  
3/30/2006  
www.MonolithicPower.com  
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.  
© 2006 MPS. All Rights Reserved.  
2
TM  
EV0035 – 6 WHITE LEDs, 20mA PRECISION WLED DRIVER EVALUATION BOARD  
PRINTED CIRCUIT BOARD LAYOUT  
Figure 1—Top Silk Layer  
Figure 2—Top Layer  
Figure 3—Bottom Layer  
EV0035 Rev. 1.2  
3/30/2006  
www.MonolithicPower.com  
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.  
© 2006 MPS. All Rights Reserved.  
3
TM  
EV0035 – 6 WHITE LEDs, 20mA PRECISION WLED DRIVER EVALUATION BOARD  
QUICK START GUIDE  
1. Solder LED1 – LED6 onto the board.  
2. Connect VCC to the power source’s positive output.  
3. Connect GND to supply ground.  
4. Remove the jumper J1 to allow the MP1523 to automatically start when power is applied. Place the  
shorting clip across J1 to disable the MP1523. A logic signal may be applied to EN to  
enable/disable the MP1523, provided the shorting clip is not installed across J1.  
5. To dim the LEDs, remove the shorting clip from J1 and apply a PWM signal to the EN pin. Adjusting  
the duty cycle of the PWM signal determines the brightness of the LEDs.  
NOTICE: The information in this document is subject to change without notice. Please contact MPS for current specifications.  
Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS  
products into any application. MPS will not assume any legal responsibility for any said applications.  
EV0035 Rev. 1.2  
3/30/2006  
www.MonolithicPower.com  
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.  
© 2006 MPS. All Rights Reserved.  
4

相关型号:

SI9130DB

5- and 3.3-V Step-Down Synchronous Converters

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1

SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1-E3

SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135_11

SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9136_11

Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130CG-T1-E3

Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130LG-T1-E3

Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130_11

Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137

Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137DB

Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137LG

Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9122E

500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification Drivers

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY