IG10009 [MPD]
IG120 SERIES;
| 型号： | IG10009 |
| 厂家： | 
MICROPOWER DIRECT, LLC |
| 描述： | IG120 SERIES |
| 文件： | 总4页 (文件大小：1019K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Series
IG120
High Isolation
IGBT Driver
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Key Features:
Conditions
Min.
Typ.
Max.
Units
• OperatesWithxx962Drivers
• Independent Outputs
• EN 60950 Approved
• 3,000 VAC Isolation
• Miniature SIP Case
• >3.5 MHour MTBF
• Seven Standard Models
• LOW COST!!
Supply Voltage Range
Input Filter
See Model Selection Guide
Internal Capacitor
Output
Parameter
Conditions
Min.
Typ.
Max.
1.ꢀ
Units
%
Line Regulation
Load Regulation
Ripple & Noise (20 MHz)
Efficiency
For VIN Change of 1%
See Note 1
1.2
6.3
100
80
1ꢀ
%
200
mV P - P
%
Temperature Coefficient
Output Short Circuit
General
0.03
%/ºC
Continuous (Autorecovery)
Parameter
Conditions
Min.
60 Seconds 3,000
1,000
Typ.
Max.
Units
VAC
M⍀
pF
Isolation Voltage
Isolation Resistance
Isolation Capacitance, 1 kHz/0.1V
Switching Frequency
EMI Characteristics
Parameter
6.6
100
300
kHz
Standard
Level
Radiated Emissions
Conducted Emissions
ESD
See Page 3
See Page 3
EN ꢀꢀ022
EN ꢀꢀ022
Class B
Class B
EN 61000-4-2
Criteria B; 8 kV Contact
Environmental
Parameter
Conditions
Min.
-40
Typ.
Max.
+10ꢀ
+12ꢀ
Units
ºC
Operating Temperature Range
Storage Temperature Range
Cooling
Ambient
+2ꢀ
-ꢀ0
ºC
Free Air Convection
RH, Non-condensing
Humidity
9ꢀ
%
Physical
Case Size
0.768 x 0.386 x 0.492 Inches (19.ꢀ0 x 9.80 x 12.ꢀ0 mm)
Non-Conductive Black Plastic (UL94-V0)
0.1ꢀ2 Oz (4.3g)
Case Material
Weight
Reliability Specifications
Parameter
Conditions
Min.
Typ.
Typ.
Max.
Units
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
MTBF
MIL HDBK 217F, 2ꢀºC, Gnd Benign
3.ꢀ
MHours
Absolute Maximum Ratings
Parameter
Conditions
Min.
Max.
13
Units
VDC
ºC
IG120-12 -0.7
IG120-12W -0.7
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
1ꢀ
Max Supply Voltage (1 Sec)
Lead Temperature
IG100-9, IG100-9D -0.7
IG120-1ꢀ, IG136-1ꢀ -0.7
IG120-24 -0.7
16
16
26
1.ꢀ mm From Case For 10 Sec
300
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com
Model Selection Guide
www.micropowerdirect.com
Load
Regulation
(%)
Current Current
Input (Supply)
Model
Output 1
Voltage (VDC)
Min. Nom. Max.
Output 2
Maximum
Capacitive
Load
Fuse Rating
Slow-Blow
(mA)
Voltage (VDC)
Voltage (VDC)
Current Current
(mA Max) (mA, Min)
Number
(mA Max) (mA, Min)
(µF)
Min. Nom. Max.
Min. Max.
Nom.
Range
IG100-09
IG100-09D
IG120-12
IG120-12W
IG120-1ꢀ
IG136-1ꢀ
IG120-24
1ꢀ 14.ꢀ - 1ꢀ.ꢀ 8.0 9.0 10.0
1ꢀ 14.ꢀ - 1ꢀ.ꢀ 8.0 9.0 10.0
12 11.6 - 12.4 14.0 1ꢀ.0 16.0
111.0
ꢀꢀ.0
80.0
100.0
80.0
80.0
80.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
8.3
8.3
6.3
6.3
6.3
6.3
6.3
1ꢀ
1ꢀ
1ꢀ
1ꢀ
1ꢀ
1ꢀ
1ꢀ
220
220
220
220
220
220
220
200
200
400
ꢀ00
300
400
200
-8.0 -9.0 -10.0
-7.0 -8.7 -10.0
-7.0 -8.0 -9.0
-7.0 -8.7 -10.0
-7.0 -8.7 -10.0
-7.0 -8.7 -10.0
ꢀꢀ.0
40.0
80.0
40.0
40.0
40.0
0.0
0.0
0.0
0.0
0.0
0.0
12
9.0 - 1ꢀ.0 14.0 1ꢀ.0 16.0
1ꢀ 14.ꢀ - 1ꢀ.ꢀ 14.0 1ꢀ.0 16.0
1ꢀ 14.ꢀ - 1ꢀ.ꢀ 16.ꢀ 17.0 18.0
24 23.3 - 24.7 14.0 1ꢀ.0 16.0
Notes:
1. Load regulation is measured from 10% load to full load. Load regulation is specified
for the primary output (output 1). The load regulation of output 2 may vary slightly.
The typical load regulation for IG100-9 and IG100-9D is 8.3%.
2. Operation at no-load will not damage these units. However, they may not meet all
specifications.
The IG100 series is designed to
operate with the IGD962 IGBT driver.
Contact the factory for more information
3. If output 2 is not used, it should be left open.
4. It is recommended that a fuse be used on the input of a power supply for protection.
See the Model Selection table above for the correct rating.
Efficiency vs Input Voltage 15 VDC Input
Efficiency vs Output Load 15 VDC Input
Efficiency vs Input Voltage 24 VDC Input
Efficiency vs Output Load 24 VDC Input
292 Page Street Ste D Stoughton, MA 02072
• TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com
Typical Connection
www.micropowerdirect.com
The IG100 series may be used in a wide variety of on-board power
distribution applications. However, it has been designed specifically to
power 962 type IGBT drivers. A typical connection to the MicroPower
Direct IGD962 is shown in the diagram above.
Go to the MPD website for complete information on our wide
line of IGBT driver products, including the IGD962. Or contact
the factory with any technical inquiries.
Some notes on this circuit (starting with the IG120-15
input) are:
1. The IG100 DC/DC should be mounted as close to the IGBT driver as
possible, to minimize the length of connecting board traces or wires.
2. The IG100 series does not include overload protection (typical of most
low power DC/DC’s). It is recommended that an external fuse be used.
The recommended fuse is shown in the model chart on page 2.
3. The addition of the input filter components (C1 and LDM) will typically
bring the circuit within the limits of EN ꢀꢀ022 Class B. The recom-
mended values for these components are shown in the table at right.
If meeting EN ꢀꢀ022 class B is not a concern, the inductor (LDM) can
be eliminated (as shown in the circuit diagram below). In this case, the
recommended value for C1 is 100 µF/3ꢀV.
Derating Curve
4. The recommended values for the output filter capacitors C2 and C3
are shown in the table at right.
ꢀ. C1, C2 and C3 should be mounted as close to the unit as possible. To
ensure peak gate current, these capacitors should have a low ESR.
The trace (or wire) between the DC/DC and the driver circuit should
be as short as possible.
6. The average output power of the driver circuit must be lower than
output power of the DC/DC.
7. Recommended values for components are:
Component
12 VIN
4.7 µF/ꢀ0V
12 µH
100 µF/3ꢀV
100 µF/3ꢀV
1ꢀ VIN
4.7 µF/ꢀ0V
12 µH
100 µF/3ꢀV
100 µF/3ꢀV
24 VIN
4.7 µF/ꢀ0V
12 µH
100 µF/3ꢀV
100 µF/3ꢀV
C1
LDM
C2
C3
MicroPower Direct
• 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com
Mechanical Dimensions
www.micropowerdirect.com
Pin Connections
Pin Function
1
2
ꢀ
6
7
+Vin
Gnd
Vout 2
Common
Vout 1
Notes:
All dimensions are typical in inches (mm)
• Tolerance x.xx = 0.02 ( 0.50)
• Pin 5 on the IG100-09 has no connection
Packing Tube Dimensions
Notes:
•
•
•
•
Tube length equals 20.866 (530), unit quantity equals 25 pcs.
Tube length equals 8.661 (220), unit quantity equals 10 pcs.
All dimensions are typical in inches (mm)
Tolerance x.xx = 0.02 ( 0.50)
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: sales@micropowerdirect.com
相关型号：
IG120100000UH20%R
General Fixed Inductor, 1 ELEMENT, 100000 uH, GENERAL PURPOSE INDUCTOR, AXIAL LEADED
VISHAY
IG12010000UH20%R
General Fixed Inductor, 1 ELEMENT, 10000 uH, GENERAL PURPOSE INDUCTOR, AXIAL LEADED
VISHAY
IG1201000UH20%R
General Fixed Inductor, 1 ELEMENT, 1000 uH, GENERAL PURPOSE INDUCTOR, AXIAL LEADED
VISHAY
IG120100MR10
General Fixed Inductor, 1 ELEMENT, 10 uH, GENERAL PURPOSE INDUCTOR, AXIAL LEADED, ROHS COMPLIANT
VISHAY
IG120100UH20%R
General Fixed Inductor, 1 ELEMENT, 100 uH, GENERAL PURPOSE INDUCTOR, AXIAL LEADED
VISHAY
©2020 ICPDF网 联系我们和版权申明