MCC5E0RX266WB0B [MOTOROLA]
RISC Microprocessor, 266MHz, CMOS, CBGA840, 31 X 31 MM, 1 MM PITCH, CERAMIC, FCBGA-840;型号: | MCC5E0RX266WB0B |
厂家: | MOTOROLA |
描述: | RISC Microprocessor, 266MHz, CMOS, CBGA840, 31 X 31 MM, 1 MM PITCH, CERAMIC, FCBGA-840 |
文件: | 总119页 (文件大小:1819K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Data Sheet
C-5e NETWORK PROCESSOR
SILICON REVISION B0
C5ENPB0-DS
Rev 05 PRODUCTION
Data Sheet
C-5e Network Processor
Silicon Revision B0
C5ENPB0-DS
Rev 05
Copyright © 2003 Motorola, Inc. All rights reserved. No part of this documentation may
be reproduced in any form or by any means or used to make any derivative work (such as
translation, transformation, or adaptation) without written permission from Motorola.
Motorola reserves the right to revise this documentation and to make changes in content
from time to time without obligation on the part of Motorola to provide notification of
such revision or change.
Motorola provides this documentation without warranty, term, or condition of any kind,
either implied or expressed, including, but not limited to, the implied warranties, terms or
conditions of merchantability, satisfactory quality, and fitness for a particular purpose.
Motorola may make improvements or changes in the product(s) and/or the program(s)
described in this documentation at any time.
C-5e, C-3e, C-5, Q-5, C-Port, and C-Ware are all trademarks of Motorola Inc. Motorola and
the stylized Motorola logo are registered in the US Patent & Trademark Office. All other
product or service names are the property of their respective owners.
CONTENTS
About This Guide
Guide Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Data Sheet Classifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using PDF Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Guide Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Related Product Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
CHAPTER 1
Functional Description
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Massive Processing Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
High Functional Integration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Channel Processors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Executive Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
System Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Fabric Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Buffer Management Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Table Lookup Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Queue Management Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
CHAPTER 2
Signal Descriptions
Signal Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Pinout Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Pin Descriptions Grouped by Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
LVTTL and LVPECL Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Clock Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
CP Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
DS1/T1 Framer Interface Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
10/100 Ethernet (RMII) Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Gigabit Ethernet (GMII) Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
6
CONTENTS
Gigabit Ethernet and Fibre Channel TBI Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
SONET OC-3 Transceiver Interface Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
SONET OC-12 Transceiver Interface Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Executive Processor System Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
PCI Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Serial Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
PROM Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
General System Interface Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Fabric Processor Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
BMU SDRAM Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
TLU SRAM Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
QMU SRAM (Internal Mode) Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
QMU to Q-5 TMC (External Mode) Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Power Supply Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Test Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
No Connection Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Signals Grouped by Pin Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
JTAG Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
JTAG Data Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Boundary Scan Cell Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
IDcode Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
JTAG Instruction Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Boundary Scan Description Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
CHAPTER 3
Electrical Specifications
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Power Sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Power and Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Thermal Management Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Internal Package Conduction Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Heat Sink Selection Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
AC Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Clock Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
CP Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
CONTENTS
7
DS1/DS3 Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
10/100 Ethernet Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Gigabit GMII Ethernet, TBI and MII Interface Timing Specifications . . . . . . . . . . . . . . . . . . 85
OC-3 Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
OC-12 Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Executive Processor Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
PCI Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
MDIO Serial Interface Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Low Speed Serial Interface Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
PROM Interface Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Fabric Processor Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
BMU Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
TLU Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
QMU SRAM (Internal Mode) Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
QMU to Q-5 TMC (External Mode) Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
CHAPTER 4
Mechanical Specifications
Package Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Package Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Keep Out Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Marking Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Reflow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
8
CONTENTS
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
LIST OF FIGURES
1
2
3
4
5
6
7
8
C-5e Network Processor Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Pin Locations (Top View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Pin Locations (Bottom View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
GMII/TBI Transmit and Receive Pin Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
PROM Interface Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
PROM Interface Timing Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Observe-Only Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Cell Design That Can Be Used for Both Input and Output Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Bringup Clock Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Package Cross Section View with Several Heat Sink Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Package with Heat Sink Mounted to the Printed Circuit Board. . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Test Loading Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
System Clock Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
DS1/DS3 Ethernet Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
10/100 Ethernet Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Gigabit Ethernet and TBI Interface Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
OC-3 Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
OC-12 Timing Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
PCI Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
MDIO Serial Interface Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Low Speed Serial Interface Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
PROM Interface Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Fabric Processor Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
BMU Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
TLU Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
QMU SRAM (Internal Mode) Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
QMU to Q-5 TMC (External Mode) Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
C-5e Network Processor BGA Package (Side View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
C-5e Network Processor BGA Package (Bottom View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
C-5e Network Processor BGA Package (Top View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
10
LIST OF FIGURES
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
LIST OF TABLES
1
2
3
4
5
6
7
8
Data Sheet Classifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Navigating Within a PDF Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
C-Port Silicon Documentation Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
C-5e Network Processor Data Sheet Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
TLU SRAM Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Clock and Reference Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
CP Physical Interface Signals and Pins (Grouped by Clusters) . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
DS1/T1 Framer Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
10/100 Ethernet Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Transmit and Receive Pin Combinations for Gigabit Ethernet and Fibre Channel . . . . . . . . . . . 35
Gigabit Ethernet (GMII/MII) Signals One Cluster Example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Gigabit Ethernet and Fibre Channel TBI Signals Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
OC-3 Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
OC-12 Signals Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
PCI Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Serial Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
PROM Interface Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
General System Interface Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Fabric Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Utopia1*, 2, 3 ATM Mode, C-5e Network Processor to Fabric Interface Pin Mapping . . . . . . 49
Utopia1*, 2, 3 PHY Mode, C-5e Network Processor to Fabric Interface Pin Mapping . . . . . . . 49
PRIZMA Mode, C-5e Network Processor to Fabric Interface Pin Mapping . . . . . . . . . . . . . . . . 50
Power X(CSIX-L0) Mode, C-5e Network Processor to Fabric Interface Pin Mapping . . . . . . . . 50
CSIX-L1 Mode, C-5e Network to Fabric Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . 51
BMU SDRAM Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
TLU SRAM Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
QMU SRAM (Internal Mode) Interface Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
QMU to Q-5 TMC (External Mode) Interface Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Power Supply Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Miscellaneous Test Signals For JTAG, Scan, and Internal Test Routines . . . . . . . . . . . . . . . . 58
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
12
LIST OF TABLES
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
No Connection Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Signals Listed by Pin Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
JTAG Internal Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
JTAG Identification Code and Its Subcomponents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Instruction Register Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
C-5e Network Processor Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
C-5e Network Processor Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . .74
C-5e Network Processor DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
C-5e Network Processor Capacitance Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
C-5e Network Processor Power and Thermal Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
System Clock Timing Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
DS1/DS3 Ethernet Timing Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
10/100 Ethernet Timing Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Gigabit GMII/MII Ethernet Interface Timing Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Gigabit TBI Interface Timing Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
OC-3 Timing Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
OC-12 Timing Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
PCI Timing Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
MDIO Serial Interface Timing Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Low Speed Serial Interface Timing Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
PROM Interface Timing Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Fabric Processor Timing Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
BMU Timing Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Signal Groups in BMU Timing Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
TLU Timing Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
Signal Groups in TLU Timing Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
QMU SRAM (Internal Mode) Timing Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Signal Groups in QMU SRAM (Internal Mode) Timing Diagrams . . . . . . . . . . . . . . . . . . . . . . . 100
QMU to Q-5 TMC (External Mode) Timing Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Signal Groups in QMU to Q-5 TMC (External Mode) Timing Diagrams. . . . . . . . . . . . . . . . . . . 102
Package Measurements (Reference Figure 28, and Figure 29 for Symbols) . . . . . . . . . . . . . 105
Keep Out Zone’s Measurements (Reference Figure 30 for Symbols). . . . . . . . . . . . . . . . . . . . 106
C-5e Network Processor Marking Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
ABOUT THIS GUIDE
Guide Overview
The C-5e Network Processor Data Sheet describes hardware layout specifications
including pinouts, memory configuration guidelines, timing diagrams, power and power
sequencing guidelines, thermal design guidelines, and mechanical specifications.
Motorola reserves the right to change the detail specifications as may be required to
permit improvements in the design of its products.
This guide assumes a good understanding of the C-5eTM Network Processor (NP)
architecture. See the C-5e/C-3e Network Processor Architecture Guide (part number
C5EC3EARCH-RM) for more detail about the hardware.
This guide also assumes good working knowledge of the C-Ware Software Toolset.
This guide covers the following topics:
• Functional Description
• Signal Descriptions
• Electrical Specifications
• Mechanical Specifications
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
14
ABOUT THIS GUIDE
Data Sheet Classifications Table 1 describes the Data Sheet classifications of Advance, Preliminary, and Production.
Table 1 Data Sheet Classifications
CLASSIFICATION
DESCRIPTION
Advance
Information
Used to advise customers of the proposed addition to the product line. This
document will typically contain some useful information including
interfacing with the user’s system and some specifications. The goal of this
document is to allow customers to begin designs but with expectation of
changes. Specification details may be changed later without notice.
Preliminary
Information
Describes pre-production or first production devices and is usually indicative
of production stage performance. Minor changes should be expected as
characteristic spreads become better controlled. Specification details may be
changed slightly without notice, but the customer can design their product
based on this data sheet.
Production Data Defines the long-term specified production limits based on fully
characterized data. It includes a disclaimer to allow improvements in
specifications and modifications that do not affect form, fit or function in
original applications; if absolute maximum ratings are changed, they should
improve rather than downgrade.
Using PDF Documents
Electronic documents are provided as PDF files. Open and view them using the Adobe®
Acrobat® Reader application, version 3.0 or later. If necessary, download the Acrobat
Reader from the Adobe Systems, Inc. web site:
http://www.adobe.com/prodindex/acrobat/readstep.html
PDF files offer several ways for moving among the document’s pages, as follows:
• To move quickly from section to section within the document, use the Acrobat
bookmarks that appear on the left side of the Acrobat Reader window. The bookmarks
provide an expandable outline view of the document’s contents. To display the
document’s Acrobat bookmarks, press the “Display both bookmarks and page” button
on the Acrobat Reader tool bar.
• To move to the referenced page of an entry in the document’s Contents or Index, click
on the entry itself, each of which is hyperlinked.
• To follow a cross-reference to a heading, figure, or table, click the blue text.
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Using PDF Documents
15
• To move to the beginning or end of the document, to move page by page within the
document, or to navigate among the pages you displayed by clicking on hyperlinks,
use the Acrobat Reader navigation buttons shown in this figure:
Beginning
of document
End of document
Previous or next hyperlink
Previous page
Next page
Table 2 summarizes how to navigate within an electronic document.
Table 2 Navigating Within a PDF Document
TO NAVIGATE THIS WAY
CLICK THIS
Move from section to section within the
document.
A bookmark on the left side of the Acrobat Reader
window
Move to an entry in the Table of Contents.
Move to an entry in the Index.
The entry itself
The page number
Move to an entry in the List of Figures or List The Figure or Table number
of Tables.
Follow a cross-reference (highlighted in blue The cross-reference text
text).
Move page by page.
The appropriate Acrobat Reader navigation
buttons
Move to the beginning or end of the
document.
The appropriate Acrobat Reader navigation
buttons
Move backward or forward among a series of The appropriate Acrobat Reader navigation
hyperlinks you have selected. buttons
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
16
ABOUT THIS GUIDE
Guide Conventions
The following visual elements are used throughout this guide, where applicable:
This icon and text designates information of special note.
Warning: This icon and text indicate a potentially dangerous procedure. Instructions
contained in the warnings must be followed.
Warning: This icon and text indicate a procedure where the reader must take
precautions regarding laser light.
This icon and text indicate the possibility of electrostatic discharge (ESD) in a procedure
that requires the reader to take the proper ESD precautions.
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Related Product Documentation
17
Related Product
Documentation
Table 3 lists the user and reference documentation for Motorola ‘s C-Port silicon
documentation set.
Q
Table 3 C-Port Silicon Documentation Set
DOCUMENT NAME
PURPOSE
DOCUMENT ID
C-5e/C-3e Network Processor Architecture Guide Describes the full architecture of the C-5e and C-3e network
C5EC3EARCH-RM
processors.
C-5e Network Processor Data Sheet
C-3e Network Processor Data Sheet
Describes hardware design specifications for the C-5e network C5ENPB0-DS
processor.
Describes hardware design specifications for the C-3e network C3ENPB0-DS
processor.
C-5 Network Processor to C-5e Network Processor Describes key architectural features of the C-5e, and highlights C5C5EDELTA-RM
Comparison Delta Document
main differences between C-5 and C-5e.
M-5 Channel Adapter Architecture Guide
M-5 Channel Adapter Data Sheet
Describes the full architecture of the M-5 channel adapter.
M5CAARCH-RM
Describes hardware design specifications for the M-5 channel M5CAA0-DS
adapter.
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
18
ABOUT THIS GUIDE
Revision History
Table 4 provides details about changes made for each revision of this guide.
Table 4 C-5e Network Processor Data Sheet Revision History
REVISION CHANGES
05
• Chapter 3, OC-12 timing specifications section, Tc12o modified to allow a greater
variety of phy components. The maximum value is consistent with previously
specified 10.0ns value.
• Corrected revision history.
04
• Chapter 2, corrected OC-3, CPn_3 signal I/O type from OPU to IPU
.
• Chapter 2, corrected JTAG identification code part number binary value.
• Chapter 2, clarified the function of the QACLKI signal for Internal Mode.
03
02
• Not released.
• Reflects the specification change of the VDD Supply Voltage from 1.2V to 1.25V.
• Chapter 3, modified power sequencing information, added IDDT and IDDF values.
• Chapter 4, modified keep out zone information.
01
• Includes updates from C-5e silicon A1 to B0 from C5ENPA1-DS Data Sheet.
Specifically, fifteen (15) maximum timing specifications were changed:
• For BMU: Tmco went from 3.4 to 3.5, Tmao went from 3.4 to 3.7, and Tmdo Tmdz,
Tmdv went from 4.0 to 4.4.
• For TLU: Ttco went from 3.4 to 4.0, Ttao went from 3.4 to 3.9, and Ttdo, Ttdz Ttdv
went from 3.7 to 4.5.
• For QMU SRAM (Internal Mode): Tqco went from 3.4 to 3.9, Tqao went from 3.4 to
3.7, and Tqdo, Tqdz, Tqdv went from 3.4 to 4.0. Also, Tqc minimum value changed
from 5.7 to 6.25 with QMU on-board memory and to 6.67 with QMU memory
daughter board.
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Chapter 1
FUNCTIONAL DESCRIPTION
Features
Key features of the C-5eTM Network Processor (NP) are its massive processing capabilities
and its high level of functional integration on one chip.
Massive Processing • Operating frequencies: up to 266MHz
Power
• 5Gbps of bandwidth (for non-blocking throughput)
• More than 4,500MIPS of computing power (for adding services throughout the
protocol stack)
• Up to 15 million packets per second transmitted at wire speed
• 17 programmable RISC Cores (for cell/packet forwarding)
• 32 programmable Serial Data Processors (for processing bit streams)
• Up to 133 million table lookups per second
• Three internal buses for 68Gbs of aggregate bandwidth
High Functional • 840 pin Ball Grid Array (BGA) package
Integration
• 16 Channel Processors including:
–
–
–
–
Embedded OC-3c, OC-12, OC-12c SONET framers
Programmable MAC interface
RISC Cores
Programmable pin PHY interfaces
• Embedded coprocessors for table lookup (classification), buffer management (payload
control), and queue management (CoS/QoS implementation)
• Dedicated Fabric Processor and port
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
20
CHAPTER 1: FUNCTIONAL DESCRIPTION
• Embedded RISC Executive Processor
• Integrated 32bit 33/66MHz PCI bus interface
Block Diagram
The C-5eTM NP, has an architecture specifically designed for networking applications. The
following sections describe each component of the C-5e NP.
The main components of the C-5e NP are:
• Channel Processors
• Executive Processor
• Fabric Processor
• Buffer Management Unit
• Table Lookup Unit
• Queue Management Unit
The C-5e NP conforms with both SONET and SDH. Therefore, OC-3(STS-3/STM-1), OC-12
(STS-12/STM-4, and OC48 (STS-48/STM-16).
Figure 1 shows a block diagram of the C-5e NP, including its potential external interfaces.
For more information about the architecture of the C-5e NP, see the C-5e/C-3e Network
Processor Architecture Guide (part number C5EC3EARCH-RM).
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Block Diagram
21
Figure 1 C-5e Network Processor Block Diagram
Q-5
(optional)
External
Host CPU
(optional)
External
PROM
(optional)
SRAM
SRAM
SDRAM
Fabric
Control
Logic
(optional)
Table
Lookup
Unit
PCI
Serial
PROM
Fabric
Processor
Executive Processor
Queue
Mgmt
Unit
Buffer
Mgmt
Unit
Buses (68Gbps Bandwidth)
Channel
Processors
CP-0 CP-1 CP-2 CP-3
PHY PHY PHY PHY
CP-12 CP-13 CP-14 CP-15
C-5e
NP
Cluster
Cluster
Processor Boundary
PHY
PHY
PHY
PHY
PHY Interface Examples:
10/100 Ethernet
Gigabit Ethernet - Aggregated
OC-3
OC-12
1xOC-48c or 48x STS-1 with M-5 Companion Device
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
22
CHAPTER 1: FUNCTIONAL DESCRIPTION
Channel Processors
The C-5e NP contains sixteen programmable Channel Processors (CPs) that receive,
process, and transmit network data. The number of CPs per port is configurable,
depending on the line interface. Typically one CP is assigned to each port for medium
bandwidth applications (Fast Ethernet to OC-3). Multiple CPs can be assigned to a port in
a configuration called channel aggregation in high bandwidth applications (greater than
OC-3). Multiple logical ports can be assigned to a single CP, with the addition of an
external multiplexor, for low bandwidth applications, such as DS1 to DS3.
The C-5e NP’s architecture supports a variety of industry-standard serial and parallel
protocols and individual port data rates including:
• 10/100Mb Ethernet (RMII)
• 1Gb Ethernet (GMII and TBI)
• OC-3c
• OC-12
• OC-48c (using various configurations with M-5 Channel Adapter)
• OC-48 (using various configurations with M-5 Channel Adapter)
• 100Mbit FibreChannel
• DS1/DS3, supported through the use of external framers/multiplexors
The C-5e NP’s programmability can also support a variety of special interfaces, such as
various xDSL encapsulations and proprietary protocols.
Key components of each CP are a RISC Core (CPRC) that orchestrates cell/packet
processing and a set of microprogrammable, special-purpose processors, called Serial
Data Processors (SDPs), that provide features such as Ethernet MAC and SONET/SDH
framing, multichannel HDLC, and ATM cell delineation. This means you usually only need
to include PHYs to complete the system.
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Executive Processor
23
Executive Processor
The Executive Processor (XP) serves as a centralized computing resource for the C-5e NP
and manages the system interfaces.
The XP performs conventional supervisory tasks in the C-5e NP, including:
• Reset and initialization of the C-5e NP
• Program loading and control of CPs
• Centralized exception handling
• Management of a host interface through the PCI
• Management of system interfaces (PCI, Serial Bus, PROM)
System Interfaces The system interfaces to the XP are:
• PCI — Provides an industry standard 32bit 33/66MHz PCI channel used for chip-level
shared resources. The PCI has both initiator and target capabilities. The PCI interface is
typically connected to a host processor.
• Serial Bus Interface — Provides a general purpose bi-directional, two-wire serial bus
and I/O port that allows the C-5e NP to control external logic with either of two
standard protocols:
–
The MDIO (high-speed) protocol: uses a 16bit data format with 10bits of
addressing and supports transfers up to 25MHz.
–
The low-speed protocol: uses an 8bit data format followed by an acknowledge bit
and supports transfers up to 400kbps.
Software is used to select which protocol to use, by setting the appropriate bits in the
Serial Bus Configuration Register. When a serial bus transfer is active, an external pin is
driven by the C-5e NP to indicate which protocol is being used (SPLD=0 indicates
MDIO protocol; SPLD=1 indicates low-speed protocol).
Both SIDA and SICL are bi-directional lines that are connected, via an external pull-up
resistor, to a positive supply voltage. When the bus is free, both lines are HIGH because
of the pull-up resistor. The output stages of the devices connected to the bus must
have either an open-drain or open-collector in order to perform the wired-AND
function required for its arbitration mechanism.
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
24
CHAPTER 1: FUNCTIONAL DESCRIPTION
• PROM Interface — Allows the XP to boot from nonvolatile, flash memory. The PROM
interface is a low-speed, serial I/O port that runs at 1/2 to 1/16 the core clock rate. The
maximum PROM size addressable is 4MBytes, and must use a “by 16” part. External
board logic is required to perform serial-to-parallel conversion for PROM address
outputs and parallel-to-serial conversion for PROM data inputs.
Fabric Processor
The Fabric Processor (FP) acts as a high-speed network interface port with advanced
functionality. It allows the C-5e NP to interface to an application-specific switching
solution internal to your design. The FP port supports the bidirectional transfer of
segments from the C-5e NP to a hardware interface that provides connectivity to other
network processors or other similar line processing hardware. There are numerous
parameters that can be configured within the FP to allow the interface to be adapted to
different fabric protocols. The FP can be configured to conform to seven (7) different
fabric interfaces that include: CSIX-L1, UTOPIA-1, -2, -3, PRIZMA, Power X(CSIX-L0), and
UTOPIA3 like to M-5.
The FP can be configured to run at any frequency up to 125MHz, with the receive and
transmit data buses up to 32 bits wide. This allows a wide range of supported bandwidths
to and from the switching fabric, all the way up to 4000 Mbps full duplex bandwidth.
Buffer Management Unit
The Buffer Management Unit (BMU) interfaces the C-5e NP to external pipeline
architecture, Single Data Rate Synchronous DRAM. The external memory is partitioned
and used as buffers for receiving and transmitting data between CPs, the FP, and the XP. It
is also used as second level storage in the XP memory hierarchy.
The interface to an array of SDRAM chips is 139bits wide, composed of 128 data bits, two
internal control bits, and nine SECDED (single error correction-double error detection) ECC
(error correction code) bits. The interface is compliant with the PC100 standard and
operates at up to 133MHz with 3.3V LVTTL-compatible inputs and outputs. The refresh
period, Trcd, Tcas, Trp, Tmrd, and Trc are configurable via boot time configuration (see the
C-5e/C-3e Network Processor Architecture Guide (part number C5EC3EARCH-RM) for more
details).
The C-5e NP non-configurable interface transfers four beats of data for each read and
write using a sequential burst type. In addition, the C-5e NP uses an auto-refresh mode for
the RAM’s.
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Table Lookup Unit
25
Some of these parameters are programmed into the SDRAMs’ mode register and can be
applied only once per power cycle. The ECC functionality can be enabled or disabled via
configuration register writes.
If needed, the interface can narrowed to 128bits by disabling ECC and providing board
pull-ups for the two control bits and nine ECC bits. This is useful if DIMMs are used in the
board design. If individual SDRAM parts are used, x16 and x32 are supported. The BMU
supports SDRAM devices that use 12 address lines. Internal address calculation paths limit
the maximum memory size to 128MBytes. Only one physical bank of SDRAM is supported.
Table Lookup Unit
The Table Lookup Unit (TLU) performs table lookups in external SRAM. It can also be used
for statistics accumulation and retrieval and as general data storage. The TLU
simultaneously supports multiple application-defined tables and multiple search
strategies, such as those needed for routing, circuit switching, and QoS lookup tasks.
The C-5e NP uses external 64bit wide ZBT Pipelined Bursting Static RAM (SRAM) modules
(at frequencies up to 133MHz) for storage of its tables. These modules allow
implementation of tables with 225 x 64bit entries using 8Mbit SRAM technology. The
maximum amount of memory supported by the TLU is 128MBytes in four banks, when
SRAM technology supports 4M x 18pins parts.
Table 5 TLU SRAM Configurations
MIN TABLE SIZE
(ONE BANK)
MAXIMUM TABLE SIZE
(FOUR BANKS)
SRAM TECHNOLOGY
1Mbit (32k x 32pins)
2Mbit (64k x 32pins)
4Mbit (256k x 18pins)
8Mbit (512k x 18pins)
16Mbit (1M x 18pins)
32Mbit (2M x 18pins)
64Mbit (4M x 18pins)
256kBytes
512kBytes
2MBytes
4MBytes
8MBytes
16MBytes
32MBytes
1MBytes
2MBytes
8MBytes
16MBytes
32MBytes
64MBytes
128MBytes
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
26
CHAPTER 1: FUNCTIONAL DESCRIPTION
Queue Management Unit
The Queue Management Unit (QMU) autonomously manages a number of
application-defined descriptor queues. It handles inter-CP and inter-C-5e NP descriptor
flows by providing switching and buffering. It also performs descriptor replication for
multicast applications. A number of up to 128 queues can be assigned to each CPRC for
QoS-based services.
The QMU provides a queuing engine internal to the chip and uses external SRAM to store
the descriptors. Scheduling is done by the CPs. The QMU supports up to 512 queues and
16, 384 descriptor buffers. A descriptor buffer holds an application-defined “descriptor”,
which is a structure that defines the payload buffer handle and other attributes of the
forwarded cell or packet.
The QMU’s external SRAM interface uses ZBT synchronous SRAMs organized in a single
bank of up to 128k, 32bit words. This interface runs at up to 160MHz frequency (refer to
Table 57 on page 99 for details).
The C-5e provides two modes for managing queues. They consist of:
• Internal Mode (using the internal QMU only)
• External Mode (using the internal QMU and the external Q-5 Traffic Management
Coprocessor).
See the C-5e/C-3e Network Processor Architecture Guide (part number C5EC3EARCH-RM) for
more details.
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Chapter 2
SIGNAL DESCRIPTIONS
Signal Summary
There are ten (10) functional groupings of signals in the C-5e Network Processor:
• Clock — 11 pins
• Channel Processors (CP0 - CP15) — 16x7 = 112 pins
• Executive Processor (XP) — 57 pins
–
–
–
–
PCI Interface — 50 pins
PROM Interface — 4 pins
Serial Bus Interface — 2 pins
General System Interface — 1 pin
• Fabric Processor (FP) — 80 pins
• Buffer Management Unit (BMU) — 160 pins
• Table Lookup Unit (TLU) — 99 pins
• Queue Management Unit (QMU) — 59 pins
• Power — 245 pins
• Test — 14 pins
• No connection (NC) — 3 pins
Two (2) of the sections (CPs and FP) are configurable, depending on the type of device
being implemented.
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
28
CHAPTER 2: SIGNAL DESCRIPTIONS
Pinout Diagram
The C-5e NP contains 840 pins. These pin numbers are referenced throughout the
remaining chapter. Figure 2 shows the pin locations from the top view. In contrast,
Figure 3 shows the pin locations from the bottom view.
Figure 2 Pin Locations (Top View)
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
AJ
AH
AG
AF
AE
AD
AC
AB
AA
Y
AJ
AH
AG
AF
AE
AD
AC
AB
AA
Y
CP0_0 CP1_0 CP1_5 CP2_4 CP3_4 CP4_4 CP5_2 CP6_1 CP7_1
CP8_1
CP8_6
CP9_0
CP9_1
CP9_2
CP9_3
CP9_4
CP9_5
GND
FOUT0 FOUT6 FOUT12 FOUT19 FOUT24 FOUT31 FTXCTL5 FIN3
FOUT1 FOUT7 FOUT13 GND FOUT25 FTXCTL0 FTXCTL6 FIN4
FIN10
VDDF
FIN11
FIN12
GND
FIN15
FIN16
FIN17
FIN18
FIN19
FIN20
FIN21
FIN22
FIN23
FIN24
FIN25
FIN29
FIN30
FIN31
GND
FRXCTL3 PAD0
PAD1
PAD2
PAD7
PAD3
VDD33
PAD4
CP0_1 VDD33 CP1_6 CP2_5 CP3_5 GND CP5_3 CP6_2 CP7_2 VDD33
GND
PAD5
PAD6
PAD8
CP0_2 CP1_1 CP2_0 CP2_6 CP3_6 CP4_5 CP5_4 CP6_3 CP7_3
CP0_3 CP1_2 VDD33 CP3_0 CP4_0 CP4_6 GND CP6_4 CP7_4
CP0_4 GND CP2_1 CP3_1 CP4_1 VDD33 CP5_5 CP6_5 CP7_5
CP0_5 CP1_3 CP2_2 CP3_2 CP4_2 CP5_0 CP5_6 CP6_6 CP7_6
CP0_6 CP1_4 CP2_3 CP3_3 CP4_3 CP5_1 CP6_0 CP7_0 CP8_0
CP8_2
CP8_3
GND
FOUT2 VDDF FOUT14 FOUT20 FOUT26
VDDF
FTXCLK FIN5
FRXCTL4 PAD9
FRXCTL5 PAD14
PAD10
PAD11 PAD12
VDD33 PAD16
PAD13
PAD17
PAD21
PAD26
PAD31
GND FOUT8 FOUT15 FOUT21 FOUT27 FTXCTL1
FOUT3 FOUT9 FOUT16 VDDF FOUT28 FTXCTL2
FOUT4 FOUT10 FOUT17 FOUT22 FOUT29 FTXCTL3
FOUT5 FOUT11 FOUT18 FOUT23 FOUT30 FTXCTL4
GND
FIN0
FIN1
FIN2
VDDF
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD33
FIN6
FIN7
FIN8
FIN9
PAD15
FIN26 FRXCTL0
VDDF
PAD18
PAD19
PAD23
PAD20
GND
CP8_4
CP8_5
FIN13
FIN14
FIN27 FRXCTL1 FRXCTL6 PAD22
FIN28 FRXCTL2 FRXCLK PAD27
PAD24 PAD25
PAD29 PAD30
PAD28
CP9_6 CPA_0 VDD33 CPA_1 CPA_2 CPA_3 GND CPA_4 CPA_5 VDD33
VDD33 GND
VDDF
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD33
MA5
MA4
MA3
MA2
MA1
MA0
JSO1
16
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDDF
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD33
GND
VDD
GND VDD33 PTRDYX PIRDYX
GND
PCBEX0 PCBEX1 PCBEX2
VDD33 PCBEX3 PPAR
CPA_6 GND CPB_0 CPB_1 CPB_2 VDD33 CPB_3 CPB_4 CPB_5
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDDT
GND
VDD
GND
VDDT
GND
GND
PREQX
PRSTX
PCLK
VDD33 PSTOPX PDEVSELX PPERRX GND
PSERRX
SPDO
TA15
TA8
CPB_6 CPC_0 CPC_1 CPC_2 CPC_3 CPC_4 CPC_5 CPC_6 CPD_0 VDD33
GND
GND
VDD
VDDT PINTA
PIDSEL PGNTX
SIDA
TA20
TA12
GND
SICL
TA19
TA11
TA4
SPCK
TA18
TA10
TA3
SPLD
TA17
GND
TA2
SPDI
TA16
TA9
W
V
W
V
CPD_1 CPD_2 CPD_3 CPD_4 CPD_5 CPD_6 CPE_0 CPE_1 CPE_2
GND
VDD
GND PFRAMEX XPUHOT TA21
CPE_3 CPE_4 GND CPE_5 CPE_6 CPF_0 VDD33 CPF_1 CPF_2 VDD33
GND
GND
VDD
VDDT
GND
TA14
TA7
TA13
TA6
VDDT
TA5
U
U
CPF_3 VDD33 CPF_4 CPF_5 CPF_6 GND
MD0
MD1
MD2
MD11
MD20
MD27
MD34
MD43
MD52
MD59
MD66
MD75
GND
VDD33
GND
VDD
VDDT
TA1
T
T
MD3
MD4
MD5
MD6
MD7
MD8
MD9 MD10
GND
GND
VDD
VDDT TWE3X
TWE2X TWE1X
TWE0X TCE3X
TCE2X
TPAR2
TD55
TD48
TD40
TD31
TD23
TD16
TD8
TCE1X TCE0X
TPAR1 TPAR0
TA0
R
R
MD12 MD13 MD14 MD15 MD16 MD17 MD18 MD19
MD21 MD22 VDD33 MD23 MD24 MD25 GND MD26
VDD
GND
VDDT
GND
VDDT
GND
VDDT
GND
VDDT
TD4
TD63
TD59
TD52
TD45
TD36
TD27
TD20
TD13
TD3
TD62
TD58
TD51
TD44
TD35
TD26
TD19
TD12
TD2
TD61
GND
TD60
TD57
VDDT
TD42
TD33
TD25
GND
TPAR3
TD56
TD49
TD41
TD32
TD24
TD17
TD9
TCLKI
TD53
TD46
TD37
TD28
TD21
TD14
TD5
P
P
VDD33
GND
GND
GND
VDD
VDDT
TD47
TD39
TD30
GND
TD15
TD7
TD54
GND
TD38
TD29
TD22
VDDT
TD6
N
N
MD28
GND
MD29 MD30 MD31 VDD33 MD32 MD33
VDD
TD50
TD43
TD34
VDDT
TD18
TD11
TD1
M
M
MD35 MD36 MD37 MD38 MD39 MD40 MD41 MD42
MD44 MD45 MD46 MD47 MD48 MD49 MD50 MD51
VDD33
GND
GND
GND
VDD
L
L
VDD
K
K
MD53 MD54
GND
MD55 MD56 MD57 VDD33 MD58
VDD33
GND
GND
GND
VDD
J
J
MD60 VDD33 MD61 MD62 MD63 GND MD64 MD65
MD67 MD68 MD69 MD70 MD71 MD72 MD73 MD74
MD76 MD77 MD78 MD79 MD80 MD81 MD82 MD83
MD85 MD86 VDD33 MD87 MD88 MD89 VDD33 MD90
VDD
GND
H
H
VDD33
VDD33 GND
GND
CCLK3
CCLK4
CCLK5
JSO2
TD10
TD0
G
G
MD84 MDECC7 MDECC2 MDQM MA11
MD91 MDECC6 MDECC1 MDQML MA10
SCLK CCLK0
SCLKX CCLK1
VDD33 CCLK2
CPREF QA13
CCLK6 QA14
CCLK7 QA15
QD23
QD24
QD25
QD26
QD27
QD28
QD16
QD17
QD18
QD19
QD20
QD21
QD22
4
QD11
VDDT
QD12
QD13
GND
QD14
QD15
3
QD6
QD7
GND
QD8
QD9
VDDT
QD10
2
QD0
F
F
QA9
QA3
QA4
QA5
QA6
QA7
QA8
9
QDPH
VDDT
QD30
GND
QD1
E
E
MD92
GND
MD93 MD94 MD95 GND MD96 MD97
MD98
GND
MDECC0 MBA0
MA9
MA8
GND
QA10
QARDY QBCLKI
QNQRDY QACLKO
QD2
D
D
MD99 MD100 MD101 MD102 MD103 MD104 MD105 MD106 MD107 MDECC5 MCASX
MD108 MD109 GND MD110 MD111 MD112 VDD33 MD113 MD114 MDECC4 MRASX
GND
JSE
JSO0
GND
QA16
QD31
QWEX
GND
QD3
C
C
MBA1 VDD33
JTCK JCLKBYP VDD33
JSO3 QDQPAR QA11
QA0
QA1
QA2
8
VDDT
QACLKI
QDPL
7
QD4
B
B
MD115 VDD33 MD116 MD117 MD118 GND MD119 MD120 MD121 VDD33
MWEX MDCLK MA7
GND
JSO4
15
JTDI
JTMS
14
JHIGHZ
JTDO
13
JSO5
NC3
VDDT
QA12
10
QD5
A
A
MD122 MD123 MD124 MD125 MD126 MD127 MD128 MD129 MDECC8 MDECC3 MCSX
NC5
MA6
JTRSTX NC4
QBCLKO QD29
29
28
27
26
25
24
23
22
21
20
19
18
17
12
11
6
5
1
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Pinout Diagram
29
Figure 3 Pin Locations (Bottom View)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
PAD4
PAD3
PAD2
PAD1
PAD0 FRXCTL3 FIN29
FIN22
FIN15
FIN10
FIN3 FTXCTL5 FOUT31 FOUT24 FOUT19 FOUT12 FOUT6 FOUT0 CP8_6
CP8_1
CP7_1 CP6_1 CP5_2 CP4_4 CP3_4 CP2_4 CP1_5 CP1_0 CP0_0
AJ
AH
AG
AF
AE
AD
AC
AB
AA
Y
AJ
AH
AG
AF
AE
AD
AC
AB
AA
Y
PAD8
VDD33 PAD7
PAD6
PAD10
PAD15
PAD19
PAD23
PAD28
PAD5
GND
FIN30
FIN23
FIN24
FIN25
FIN16
FIN17
FIN18
FIN19
FIN20
FIN21
VDDF
FIN11
FIN12
GND
FIN4 FTXCTL6 FTXCTL0 FOUT25
GND FOUT13 FOUT7 FOUT1 CP9_0
VDD33
CP8_2
CP8_3
GND
CP7_2 CP6_2 CP5_3
GND
CP3_5 CP2_5 CP1_6 VDD33 CP0_1
PAD13 PAD12 PAD11
PAD17 PAD16 VDD33
PAD9 FRXCTL4 FIN31
FIN5 FTXCLK
VDDF
FOUT26 FOUT20 FOUT14 VDDF FOUT2 CP9_1
CP7_3 CP6_3 CP5_4 CP4_5 CP3_6 CP2_6 CP2_0 CP1_1 CP0_2
PAD14 FRXCTL5
GND
FIN6
FIN7
FIN8
FIN9
GND
FIN0
FIN1
FIN2
VDDF
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD33
FTXCTL1 FOUT27 FOUT21 FOUT15 FOUT8 GND
CP9_2
CP7_4 CP6_4 GND
CP4_6 CP4_0 CP3_0 VDD33 CP1_2 CP0_3
PAD21
GND PAD20
PAD18
VDDF FRXCTL0 FIN26
FTXCTL2 FOUT28 VDDF FOUT16 FOUT9 FOUT3 CP9_3
FTXCTL3 FOUT29 FOUT22 FOUT17 FOUT10 FOUT4 CP9_4
FTXCTL4 FOUT30 FOUT23 FOUT18 FOUT11 FOUT5 CP9_5
CP7_5 CP6_5 CP5_5 VDD33 CP4_1 CP3_1 CP2_1
GND
CP0_4
PAD26 PAD25 PAD24
PAD31 PAD30 PAD29
PPAR PCBEX3 VDD33
PAD22 FRXCTL6 FRXCTL1 FIN27
PAD27 FRXCLK FRXCTL2 FIN28
FIN13
FIN14
CP8_4
CP8_5
VDD33
GND
CP7_6 CP6_6 CP5_6 CP5_0 CP4_2 CP3_2 CP2_2 CP1_3 CP0_5
CP8_0 CP7_0 CP6_0 CP5_1 CP4_3 CP3_3 CP2_3 CP1_4 CP0_6
CPA_5 CPA_4 GND CPA_3 CPA_2 CPA_1 VDD33 CPA_0 CP9_6
PCBEX2 PCBEX1 PCBEX0
GND
PIRDYX PTRDYX VDD33 GND
GND
VDD
VDDF
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
SCLK
VDDF
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD33
MA5
MA4
MA3
MA2
MA1
MA0
JSO1
GND VDD33
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
PSERRX GND PPERRX PDEVSELX PSTOPX VDD33
PCLK PRSTX
PGNTX PIDSEL
PREQX
PINTA
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDDT
GND
VDD
GND
VDDT
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
VDD
GND
CPB_5 CPB_4 CPB_3 VDD33 CPB_2 CPB_1 CPB_0
GND
CPA_6
SPDO
TA15
TA8
SPDI
TA16
TA9
SPLD
TA17
GND
TA2
SPCK
TA18
TA10
TA3
SICL
TA19
TA11
TA4
SIDA
TA20
TA12
GND
VDDT
GND
VDD
VDD33
GND
CPD_0 CPC_6 CPC_5 CPC_4 CPC_3 CPC_2 CPC_1 CPC_0 CPB_6
CPE_2 CPE_1 CPE_0 CPD_6 CPD_5 CPD_4 CPD_3 CPD_2 CPD_1
TA21 XPUHOT PFRAMEX GND
GND
VDD
W
V
W
V
VDDT
TA5
TA13
TA6
TA14
TA7
VDDT
GND
VDDT
GND
VDDT
GND
VDDT
GND
VDDT
GND
VDDT
TD4
GND
VDD
VDD33
GND
CPF_2 CPF_1 VDD33 CPF_0 CPE_6 CPE_5
GND
CPE_4 CPE_3
TA1
VDDT
GND
VDD
MD2
MD1
MD0
MD9
GND CPF_6 CPF_5 CPF_4 VDD33 CPF_3
U
U
TA0
TCE0X TCE1X
TCE2X
TPAR2
TD55
TD48
TD40
TD31
TD23
TD16
TD8
TCE3X TWE0X TWE1X TWE2X
TWE3X
TD63
TD59
TD52
TD45
TD36
TD27
TD20
TD13
TD3
GND
VDD
VDD33
GND
MD11
MD20
MD27
MD34
MD43
MD52
MD59
MD66
MD75
MD10
MD8
MD7
MD6
MD5
MD4
MD3
T
T
TCLKI TPAR0 TPAR1
TPAR3
TD56
TD49
TD41
TD32
TD24
TD17
TD9
TD60
TD57
VDDT
TD42
TD33
TD25
GND
TD61
GND
TD62
TD58
TD51
TD44
TD35
TD26
TD19
TD12
TD2
GND
VDD
MD19 MD18
MD17 MD16
MD25 MD24
MD15
MD14
MD13
MD12
MD21
MD28
MD35
MD44
MD53
R
R
TD53
TD46
TD37
TD28
TD21
TD14
TD5
TD54
GND
TD38
TD29
TD22
VDDT
TD6
VDDT
TD47
TD39
TD30
GND
GND
VDD
VDD33
GND
MD26
GND
MD23 VDD33 MD22
P
P
TD50
TD43
TD34
VDDT
TD18
TD11
TD1
GND
VDD
MD33 MD32 VDD33 MD31
MD30
MD38
MD47
MD55
MD62
MD70
MD79
MD29
MD37
MD46
GND
GND
MD36
MD45
MD54
N
N
GND
VDD
VDD33
GND
MD42 MD41
MD51 MD50
MD40 MD39
MD49 MD48
M
M
GND
VDD
L
L
GND
VDD
VDD33
GND
MD58 VDD33 MD57 MD56
K
K
TD15
TD7
GND
VDD33
CCLK0
MD65 MD64
MD74 MD73
MD83 MD82
GND
MD63
MD61 VDD33 MD60
J
J
TD10
TD0
GND
CCLK3
CCLK4
CCLK5
JSO2
GND VDD33
VDD33
MD72 MD71
MD81 MD80
MD69
MD78
MD68
MD77
MD67
MD76
MD85
MD92
H
H
QD0
QD1
QD2
QD3
QD4
QD5
QD6
QD11
VDDT
QD12
QD13
GND
QD16
QD17
QD18
QD19
QD20
QD21
QD22
QD23
QD24
QD25
QD26
QD27
QD28
QA13 CPREF
MA11 MDQM MDECC2 MDECC7 MD84
MA10 MDQML MDECC1 MDECC6 MD91
G
G
QD7
QD30
GND
VDDT
QDPH
QA3
QA9
QA14
QA15
QA16
CCLK6
CCLK7
GND
CCLK1 SCLKX
CCLK2 VDD33
MD90 VDD33 MD89 MD88
MD87 VDD33 MD86
F
F
GND
QD8
QBCLKI QARDY
QACLKO QNQRDY
QA4
GND
QA10
MA9
MA8
MBA0 MDECC0
GND
MD98
MD97 MD96
GND
MD95
MD94
MD93
GND
E
E
QD31
QWEX
GND
QA5
JSO0
JSE
GND MCASX MDECC5 MD107 MD106 MD105 MD104 MD103 MD102 MD101 MD100 MD99
D
D
QD9
VDDT
QA0
QA1
QA2
QA6
QA11 QDQPAR JSO3
VDD33 JCLKBYP JTCK
VDD33 MBA1 MRASX MDECC4 MD114 MD113 VDD33 MD112 MD111 MD110 GND
MD109 MD108
C
C
VDDT QD14
QACLKI
QA7
VDDT
QA12
NC3
NC4
JSO5
JHIGHZ
JTDO
JTDI
GND
MA7 MDCLK MWEX
VDD33
MD121 MD120 MD119 GND MD118 MD117 MD116 VDD33 MD115
B
B
QD10
QD15
QD29 QBCLKO QDPL
QA8
JTRSTX
JTMS
JSO4
MA6
NC5
MCSX MDECC3 MDECC8 MD129 MD128 MD127 MD126 MD125 MD124 MD123 MD122
A
A
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
30
CHAPTER 2: SIGNAL DESCRIPTIONS
Pin Descriptions Grouped
by Function
The C-5e NP pins are categorized in groups, reflecting interfaces to the chip:
• Clock Signals
• CP Interface Signals
• Executive Processor System Interface Signals
• Fabric Processor Interface Signals
• BMU SDRAM Interface Signals
• TLU SRAM Interface Signals
• QMU SRAM (Internal Mode) Interface Signals
• QMU to Q-5 TMC (External Mode) Interface Signals
• Power Supply Signals
• Test Signals
• No Connection Pins
Pins conform to Joint Electronic Devices Engineering Council (JEDEC) standards.
LVTTL and LVPECL C-5e NP pins are the following types:
Specifications
• Low Voltage TTL-Compatible (LVTTL). The C-5e NP’s LVTTL pins conform to the JEDEC
JESD8-B specification.
• Low Voltage Positive Emitter Coupled Logic (LVPECL).
All of the signals in the following tables in this chapter denote whether the individual
signal is an Input (I), Output (O), both Input and Output (I/O), or power (P). In addition, a
PU, PD, and nc are used. The PU indicates that an internal resistor will pullup the pad if
left unconnected. PD indicates an internal pulldown resistor. NC means the pad is to be
left unconnected.
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Pin Descriptions Grouped by Function
31
Clock Signals Table 6 describes the C-5e NP clock signals.
Table 6 Clock and Reference Signals
SIGNAL NAME
PIN #
TOTAL
TYPE
I/O
SIGNAL DESCRIPTION
SCLK*
SCLKX*
G15
F15
1
1
LVPECL
LVPECL
I
I
Core Clock Rate (Differential)
CCLK0
CCLK1
CCLK2
CCLK3
CCLK4
CCLK5
CCLK6
CCLK7
CPREF‡
TOTAL
G14
F14
E14
G13
F13
E13
F12
E12
G12
1
1
1
1
1
1
1
1
1
11
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVPECL
IPD
IPD
IPD
IPD
IPD
IPD
IPD
IPD
IPD
1_544MHZ_CLK (T1)†
2_048MHZ_CLK (E1)†
34_368MHZ_CLK (E3)†
44_736MHZ_CLK (T3)†
50MHZ_CLK (100Mbit Ethernet)†
106_25MHZ_CLK (Fibre Channel)†
125MHZ_CLK (Gigabit Ethernet)†
155_52MHZ_CLK (OC-3)†
Reference
*
SCLK and SCLKX must not be AC-coupled.
†
The frequencies specified for CCLK0 - CCLK7 allow full flexibility for the C-5e NP. It is also possible to use one
or more CCLKn inputs for other frequencies. Contact your Motorola representative for more information.
If any of the CPs are configured for LVPECL operation (OC3) using the pin mode registers, then CPREF must
be wired to an external reference, as specified in Table 38 on page 75. If none of the CPs are configured for
LVPECL operation, then the CPREF pin can be left unconnected.
‡
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
32
CHAPTER 2: SIGNAL DESCRIPTIONS
CP Interface Signals The C-5e NP’s 16 CPs support various network physical interfaces, providing a serial
interface to the PHY layer. Interfaces are configured via bits in the C-5e NP register set.
Many interfaces are possible by programming the configuration registers. CPs can be
used individually or in a cluster (four CPs) to implement the various interfaces.
Table 7 provides a quick reference of all the CP pins organized by clusters. There are seven
physical I/O pins associated with each CP. All pins are capable of receiving data, with some
configurable to be input clocks, output clocks, or data drivers. In addition, pairs of pins can
be configured as differential pairs for LVPECL compatibility.
In the case of RMII, OC-3, DS1, and DS3, the drivers and receivers at the pin are locally
configured to match the relevant PHY or Framer chip. OC-12 uses the aggregation of four
CPs (one cluster), while GMII and Ten Bit Interface (TBI) can use either eight CPs (four for
receive and four for transmit) or four CPs that share the transmit and receive functions for
non-wire speed applications.
During CP aggregation, all 28 pins associated with a cluster are routed to all of the Serial
Data Processors (SDPs) in that cluster. This allows round-robin usage of portions of the
SDPs, with each getting access to the necessary I/O pins.
The signals for the following CP physical interfaces are included in this section:
• DS1/T1 Framer Interface Configuration
• 10/100 Ethernet (RMII) Configuration
• Gigabit Ethernet (GMII) Configuration
• Gigabit Ethernet and Fibre Channel TBI Configuration
• SONET OC-3 Transceiver Interface Configuration
• SONET OC-12 Transceiver Interface Configuration
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Pin Descriptions Grouped by Function
33
Table 7 CP Physical Interface Signals and Pins (Grouped by Clusters)
CP CLUSTER 1 CP CLUSTER 2 CP CLUSTER 3
SIGNAL SIGNAL SIGNAL
CP CLUSTER 4
SIGNAL
PIN #
AJ29
AH29
AG29
AF29
AE29
AD29
AC29
AJ28
AG28
AF28
AD28
AC28
AJ27
AH27
AG27
AE27
AD27
AC27
AJ26
AH26
AG26
AF26
AE26
AD26
AC26
AJ25
AH25
AG25
PIN #
AF25
AE25
AD25
AC25
AJ24
AG24
AF24
AD24
AC24
AJ23
AH23
AG23
AE23
AD23
AC23
AJ22
AH22
AG22
AF22
AE22
AD22
AC22
AJ21
AH21
AG21
AF21
AE21
AD21
PIN #
AC21
AJ20
AG20
AF20
AD20
AC20
AJ19
AH19
AG19
AF19
AE19
AD19
AC19
AB29
AB28
AB26
AB25
AB24
AB22
AB21
AA29
AA27
AA26
AA25
AA23
AA22
AA21
Y29
PIN #
Y28
Y27
Y26
Y25
Y24
Y23
Y22
Y21
W29
W28
W27
W26
W25
W24
W23
W22
W21
V29
V28
V26
V25
V24
V22
V21
U29
U27
U26
U25
CP0_0
CP0_1
CP0_2
CP0_3
CP0_4
CP0_5
CP0_6
CP1_0
CP1_1
CP1_2
CP1_3
CP1_4
CP1_5
CP1_6
CP2_0
CP2_1
CP2_2
CP2_3
CP2_4
CP2_5
CP2_6
CP3_0
CP3_1
CP3_2
CP3_3
CP3_4
CP3_5
CP3_6
CP4_0
CP4_1
CP4_2
CP4_3
CP4_4
CP4_5
CP4_6
CP5_0
CP5_1
CP5_2
CP5_3
CP5_4
CP5_5
CP5_6
CP6_0
CP6_1
CP6_2
CP6_3
CP6_4
CP6_5
CP6_6
CP7_0
CP7_1
CP7_2
CP7_3
CP7_4
CP7_5
CP7_6
CP8_0
CP8_1
CP8_2
CP8_3
CP8_4
CP8_5
CP8_6
CP9_0
CP9_1
CP9_2
CP9_3
CP9_4
CP9_5
CP9_6
CPA_0
CPA_1
CPA_2
CPA_3
CPA_4
CPA_5
CPA_6
CPB_0
CPB_1
CPB_2
CPB_3
CPB_4
CPB_5
CPB_6
CPC_0
CPC_1
CPC_2
CPC_3
CPC_4
CPC_5
CPC_6
CPD_0
CPD_1
CPD_2
CPD_3
CPD_4
CPD_5
CPD_6
CPE_0
CPE_1
CPE_2
CPE_3
CPE_4
CPE_5
CPE_6
CPF_0
CPF_1
CPF_2
CPF_3
CPF_4
CPF_5
CPF_6
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
34
CHAPTER 2: SIGNAL DESCRIPTIONS
DS1/T1 Framer Interface Configuration
Table 8 describes the serial framer interface signals. For each CP (0-15), you can
implement one serial Framer interface.
Table 8 DS1/T1 Framer Interface Signals
SIGNAL NAME*
CPn_0
PIN #†
TOTAL TYPE
I/O
OPD TCLK
IPU RCLK
LABEL
SIGNAL DESCRIPTION
Transmit Clock (1.544MHz)
Receive Clock (1.544MHz)
Transmit Data
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
1
1
1
1
1
1
1
7
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
nc
CPn_1
CPn_2
OPD TData
CPn_3
OPU TFrame
Transmit Frame Synchronization
Receive Data
CPn_4
IPD
IPU
RData
CPn_5
RFrame
Receive Frame Synchronization
nc
CPn_6
ncPU nc
TOTAL PINS
*
n can be from 0 to 15. See Table 7.
Reference Table 7 for pin numbers for the actual cluster(s) you are configuring.
†
10/100 Ethernet (RMII) Configuration
Table 9 describes the 10/100BASE-T Ethernet Reduced Media Independent Interface
(RMII) signals. For each CP (0-15), you can implement one 10/100 Ethernet interface.
Table 9 10/100 Ethernet Signals
SIGNAL NAME*
CPn_0
PIN #
TOTAL TYPE
I/O
OPD
IPU
LABEL
SIGNAL DESCRIPTION
Table 7
Table 7
1
1
LVTTL
LVTTL
REF_CLK
CRS_DV
Transmit and Receive Clock (50MHz)
CPn_1
Carrier Sense (CRS)/ Receive Data Valid (RX_DV). CRS indicates that
traffic is on the link, and is asserted if the signal is a 1 or an
alternating 1010... RX_DV indicates that a receive frame is in
progress and the data present on the RXD pins is valid. It is
asserted if this signal is a 1 for more than one cycle.
CPn_2
CPn_3
CPn_4
CPn_5
CPn_6
Table 7
Table 7
Table 7
Table 7
Table 7
1
1
1
1
1
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
OPD
OPU
IPD
TXD(0)
TXD(1)
RXD(0)
RXD(1)
TX_EN
Transmit Data 0 (first on wire)
Transmit Data 1 (second on wire)
Receive Data 0 (first on wire)
Receive Data 1 (second on wire)
IPU
OPU
Transmit Enable. When asserted, the data on TXD is encoded and
transmitted on the twisted pair cable.
7
TOTAL PINS
*
n can be from 0 to 15. See Table 7.
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Pin Descriptions Grouped by Function
35
Gigabit Ethernet (GMII) Configuration
Gigabit Ethernet Media Independent Interface (GMII) is configured in one of two ways:
• Use one CP cluster when density is more important than wire-speed performance
because you can then implement up to four Gigabit Ethernet ports per C-5e NP.
• Use two CP clusters for wire-speed performance and additional processing power. You
can implement up to two Gigabit Ethernet ports per C-5e NP.
Table 10 lists the possible CP cluster combinations you can use and Figure 4 shows receive
and transmit pin configurations by cluster. Table 11 lists the signals and pinouts for
Gigabit Ethernet (GMII).
Table 10 Transmit and Receive Pin Combinations for Gigabit Ethernet and Fibre Channel
CLUSTER
SINGLE CLUSTER MODE (TBI OR GMII)
Port 1 Tx and Rx
TWO CLUSTER MODE (GMII)*
Port 1 Tx
0
1
2
3
Port 2 Tx and Rx
Port 1 Rx
Port 3 Tx and Rx
Port 2 Tx
Port 4 Tx and Rx
Port 2 Rx
*
The Two Cluster Mode column lists typical configurations. Any cluster can be set up to either receive
or transmit. So you could configure a dual cluster mode where cluster 0 receives and cluster 3
transmits.
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
36
CHAPTER 2: SIGNAL DESCRIPTIONS
Figure 4 GMII/TBI Transmit and Receive Pin Configurations
Single Cluster Mode
Pin Configuration
Two Cluster Mode
Pin Configuration
Tx
Tx
Rx
Cluster
0
Cluster
0
}
}
}
}
Port 1
Port 2
Port 3
Port 4
Rx
nc
Port 1
Port 2
Tx
nc
Tx
Rx
}
}
Cluster
1
Cluster
1
Rx
Tx
Tx
Rx
Cluster
2
Cluster
2
Rx
nc
Tx
nc
Tx
Rx
Cluster
3
Cluster
3
Rx
nc = not connected
Table 11 Gigabit Ethernet (GMII/MII) Signals One Cluster Example
SIGNAL NAME*
PIN #† TOTAL TYPE
I/O
LABEL
SIGNAL DESCRIPTION
CPn_0
Table 7
1
LVTTL OPD T_CLK
GMII Transmit Clock (125MHz). This clock is used to synchronize the
transmit data.
CPn_1
Table 7
1
LVTTL IPU
TCLKI
MII transmit clock. Transmit data aligned to this clock input from
phy in MII mode. 25 Mhz in 100BaseT, 2.5 in Mhz in 10BaseT
CPn_2
CPn_3
CPn_4
CPn_5
CPn_6
Table 7
Table 7
Table 7
Table 7
Table 7
1
1
1
1
1
LVTTL OPD TXD(0)
LVTTL OPU TXD(1)
LVTTL OPD TXD(2)
LVTTL OPU TXD(3)
LVTTL OPU TX_EN
Transmit Data (byte-wide data, least significant bit)
Transmit Data
Transmit Data
Transmit Data
Transmit Enable. When asserted, the data on TXD is encoded and
transmitted on the twisted pair cable.
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Pin Descriptions Grouped by Function
37
Table 11 Gigabit Ethernet (GMII/MII) Signals One Cluster Example (continued)
SIGNAL NAME*
CPn+1_0
PIN #† TOTAL TYPE
I/O
ncPD nc
LVTTL IPU COL
LABEL
SIGNAL DESCRIPTION
Table 7
Table 7
1
1
nc
nc
CPn+1_1
Collision. Asserted when both RX_DV and TX_EN are valid during
half duplex operation.
CPn+1_2
CPn+1_3
CPn+1_4
CPn+1_5
CPn+1_6
Table 7
Table 7
Table 7
Table 7
Table 7
1
1
1
1
1
LVTTL OPD TXD(4)
LVTTL OPU TXD(5)
LVTTL OPD TXD(6)
LVTTL OPU TXD(7)
LVTTL OPU TX_ER
Transmit Data
Transmit Data
Transmit Data
Transmit Data (byte-wide receive data, most significant bit)
Transmit Error. Asserting TX_ER when TX_EN is a 1 causes
transmission of the designated “bad code” in lieu of the normal
encoded data on the twisted pair data.
CPn+2_0
CPn+2_1
CPn+2_2
CPn+2_3
CPn+2_4
CPn+2_5
CPn+2_6
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
1
1
1
1
1
1
1
nc
ncPD nc
nc
LVTTL IPU
LVTTL IPD
LVTTL IPU
LVTTL IPD
LVTTL IPU
LVTTL IPU
RCLK
Receive Clock (125MHz)
RXD(0)
RXD(1)
RXD(2)
RXD(3)
RX_DV
Receive Data (byte-wide receive data, least significant bit)
Receive Data
Receive Data
Receive Data
Receive Data Valid. Indicates that there is a receive frame in progress
and that the data present on the RXD signals is valid.
CPn+3_0
CPn+3_1
Table 7
Table 7
1
1
nc
ncPD nc
nc
LVTTL IPU
CRS
Carrier Sense. Indicates traffic is on the link. CRS is asserted when a
non-idle condition is detected on the receive data stream. CRS is
deasserted when an end of frame or idle condition is detected.
CPn+3_2
CPn+3_3
CPn+3_4
CPn+3_5
CPn+3_6
Table 7
Table 7
Table 7
Table 7
Table 7
1
1
1
1
1
LVTTL IPD
LVTTL IPU
LVTTL IPD
LVTTL IPU
LVTTL IPU
RXD(4)
RXD(5)
RXD(6)
RXD(7)
RX_ER
Receive Data
Receive Data
Receive Data
Receive Data (most significant bit)
Receive Error Detected. Indicates that there has been an error
received in the receive frame.
28
TOTAL PINS
*
n can be 0, 4, 8, or 12.
Reference Table 7 for pin numbers for the actual cluster(s) you are configuring.
†
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
38
CHAPTER 2: SIGNAL DESCRIPTIONS
Gigabit Ethernet and Fibre Channel TBI Configuration
1000BASE-T Gigabit Ethernet and Fibre Channel TBI is implemented in much the same
way as Gigabit Ethernet (GMII). Table 10 shows the possible CP pin combinations you can
use and Figure 4 shows receive and transmit pin configurations by cluster. Table 12 shows
the signals and pinouts for a single cluster for Gigabit Ethernet and Fibre Channel TBI.
Table 12 Gigabit Ethernet and Fibre Channel TBI Signals Example
SIGNAL NAME*
PIN #† TOTAL TYPE
I/O
LABEL
SIGNAL DESCRIPTION
CPn_0
Table 7
1
LVTTL
OPD
TCLK
Transmit Clock (125MHz). This clock is used to synchronize the
transmit data.
CPn_1
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
nc
ncPU nc
nc
CPn_2
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
nc
OPD
OPU
OPD
OPU
OPU
TXD(9)
Transmit Data (ten bits wide, last on wire)
CPn_3
TXD(8)
TXD(7)
TXD(6)
TXD(1)
Transmit Data
CPn_4
Transmit Data
CPn_5
Transmit Data
CPn_6
Transmit Data
CPn+1_0
CPn+1_1
CPn+1_2
CPn+1_3
CPn+1_4
CPn+1_5
CPn+1_6
CPn+2_0
CPn+2_1
CPn+2_2
CPn+2_3
CPn+2_4
CPn+2_5
CPn+2_6
CPn+3_0
CPn+3_1
ncPD nc
ncPU nc
nc
nc
nc
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
nc
OPD
OPU
OPD
OPU
OPU
TXD(5)
Transmit Data
TXD(4)
TXD(3)
TXD(2)
TXD(0)
Transmit Data
Transmit Data
Transmit Data
Transmit Data (ten bits wide, first on wire)
ncPD nc
nc
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
nc
IPU
IPD
IPU
IPD
IPU
IPU
RCLK
Receive Clock (62.5 MHz)
Receive Data (ten bits wide, last on wire)
Receive Data
RXD(9)
RXD(8)
RXD(7)
RXD(6)
RXD(1)
Receive Data
Receive Data
Receive Data
ncPD nc
IPU RCLKN
nc
LVTTL
Receive Clock Inverted
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Pin Descriptions Grouped by Function
39
Table 12 Gigabit Ethernet and Fibre Channel TBI Signals Example (continued)
SIGNAL NAME*
CPn+3_2
PIN #† TOTAL TYPE
I/O
IPD
IPU
IPD
IPU
IPU
LABEL
SIGNAL DESCRIPTION
Table 7
Table 7
Table 7
Table 7
Table 7
1
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
RXD(5)
RXD(4)
RXD(3)
RXD(2)
RXD(0)
Receive Data
CPn+3_3
1
Receive Data
CPn+3_4
1
Receive Data
CPn+3_5
1
Receive Data
CPn+3_6
1
Receive Data (ten bits wide, first on wire)
28
TOTAL PINS
*
n can be 0, 4, 8, or 12
Reference Table 7 for pin numbers for the actual cluster(s) you are configuring.
†
SONET OC-3 Transceiver Interface Configuration
Table 13 describes the SONET Optical Carrier (OC) 3 transceiver interface signals. For each
CP (0-15), you can implement a single OC-3 interface.
Table 13 OC-3 Signals
SIGNAL NAME*
CPn_0
PIN #†
TOTAL TYPE
I/O
LABEL
SIGNAL DESCRIPTION
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
1
1
1
1
1
1
1
LVPECL IPD
LVPECL IPU
RCLK_H
RCLK_L
Receive Clock noninverted side of pair (155.52MHz)
Receive Clock inverted side of pair (155.52MHz)
Transmit Data noninverted side of pair
Transmit Data inverted side of pair
Receive Data noninverted side of pair
Receive Data inverted side of pair
CPn_1
CPn_2
LVPECL OPD TXD_H
LVPECL OPU TXD_L
CPn_3
CPn_4
LVPECL IPD
LVPECL IPU
LVPECL IPU
RXD_H
RXD_L
CPn_5
CPn_6
SIGNAL_DET A light level above a certain threshold is present at the optical
receiver - single ended LVPECL.
7
TOTAL PINS
*
n can be from 0 to 15.
Reference Table 7 for pin numbers for the actual cluster(s) you are configuring.
†
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
40
CHAPTER 2: SIGNAL DESCRIPTIONS
SONET OC-12 Transceiver Interface Configuration
SONET Optical Carrier (OC) 12 is implemented by using one cluster of CPs. At any time, a
CP within a cluster spends half its time performing receive functions, and the other half
performing transmit functions. Table 14 shows a CP Cluster configured for one OC-12
interface.
Table 14 OC-12 Signals Example
SIGNAL NAME*
PIN #†
TOTAL TYPE
I/O
LABEL
SIGNAL DESCRIPTION
CPn_0
Table 7
1
LVTTL
OPD
TCLK
Deskewed Transmit Clock (77.76MHz). This clock is used to
synchronize the transmit data.
CPn_1
Table 7
1
LVTTL
IPU
TCLKI
Transceiver Transmit Clock. This clock sets the frequency of the
transmit data and is typically sourced by the PHY chip.
CPn_2
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
nc
OPD
OPU
OPD
OPU
OPU
TXD(0)
TXD(1)
TXD(2)
TXD(3)
OOF
Transmit Data (byte-wide data, least significant bit)
CPn_3
Transmit Data
CPn_4
Transmit Data
CPn_5
Transmit Data
CPn_6
Out of Frame
CPn+1_0
CPn+1_1
CPn+1_2
CPn+1_3
CPn+1_4
CPn+1_5
CPn+1_6
CPn+2_0
CPn+2_1
CPn+2_2
CPn+2_3
CPn+2_4
CPn+2_5
CPn+2_6
ncPD nc
ncPU nc
nc
nc
nc
LVTTL
LVTTL
LVTTL
LVTTL
nc
OPD
OPU
OPD
OPU
TXD(4)
Transmit Data
TXD(5)
TXD(6)
TXD(7)
Transmit Data
Transmit Data
Transmit Data (byte-wide data, most significant bit)
ncPU nc
ncPD nc
nc
nc
nc
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
IPU
IPD
IPU
IPD
IPU
IPU
RCLK
Receive Clock (77.76MHz)
RXD(0)
RXD(1)
RXD(2)
RXD(3)
FP
Receive Data (byte-wide receive data, least significant bit)
Receive Data
Receive Data
Receive Data
Frame Synchronization Pulse. This is valid during the third A2 of
the receive SONET frame.
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Pin Descriptions Grouped by Function
41
Table 14 OC-12 Signals Example (continued)
SIGNAL NAME*
CPn+3_0
CPn+3_1
CPn+3_2
CPn+3_3
CPn+3_4
CPn+3_5
CPn+3_6
PIN #†
TOTAL TYPE
I/O
LABEL
SIGNAL DESCRIPTION
nc
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
Table 7
1
nc
ncPD nc
ncPU nc
1
nc
nc
1
LVTTL
LVTTL
LVTTL
LVTTL
nc
IPD
IPU
IPD
IPU
RXD(4)
Receive Data
Receive Data
Receive Data
1
RXD(5)
RXD(6)
RXD(7)
1
1
Receive Data (most significant bit)
nc
1
ncPU nc
28
TOTAL PINS
*
n can be 0, 4, 8, or 12
Reference Table 7 for pin numbers for a different cluster.
†
Executive Processor The XP’s system interface manages the supervisory controls for the network interfaces, as
System Interface Signals
well as the set of pins that provide interfaces to other components in the system that are
not memories or network interfaces. It is also the primary interface used for initializing the
C-5e NP after reset. The XP signals include PCI signals, Serial interface signals, and PROM
interface signals.
PCI Signals
The PCI can be configured to support a 32bit PCI capable of operating at either 33MHz or
66MHz. The PCI is fully compliant with PCI Specification revision 2.1. Table 15 describes
the PCI signals.
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
42
CHAPTER 2: SIGNAL DESCRIPTIONS
Table 15 PCI Signals
SIGNAL NAME
PIN #
TOTAL TYPE
I/O
SIGNAL DESCRIPTION
PAD0 - PAD31
AJ5, AJ4, AJ3, AJ2, AJ1, AH5, AH4, 32
AH3, AH1, AG5, AG4, AG3, AG2,
AG1, AF5, AF4, AF2, AF1, AE5,
AE4, AE3, AE1, AD5, AD4, AD3,
AD2, AD1, AC5, AC4, AC3, AC2,
AC1
PCI
I/O Multiplexed Address/Data Bus. These signals are
multiplexed address and data bits. The C-5e NP
receives addresses as target and drives addresses as
master. It drives the data and receives read data as
master.
PCBEX0 - PCBEX3
PPAR
AB6, AB5, AB4, AB2
4
PCI
PCI
I/O Command byte enables. These signals are
multiplexed command and byte enabled signals.
The C-5e NP receives byte enables as target and drives
byte enables as master.
AB1
1
I/O Parity. This signal carries even parity for AD and CBE#
pins. It has the same receive and drive characteristics
as the address and data bus, except that it is one PCI
cycle later.
PFRAMEX
PTRDYX
PIRDYX
PSTOPX
PDEVSELX
PPERRX
PSERRX
PCLK
W9
1
1
1
1
1
1
1
1
1
1
1
1
1
50
PCI
PCI
PCI
PCI
PCI
PCI
PCI
IPD
I/O Cycle frame
AB9
AB8
AA5
AA4
AA3
AA1
AA7
AA8
AA9
Y7
I/O Target ready for data transfer
I/O Initiator ready for data transfer
I/O Target transaction stop request
I/O Target device selected
I/O Bus parity error
I/O System error
I
Bus clock
PRSTX
PCI
PCI
IPD
I
Bus reset
PREQX
O
I
Initiator bus request (arbitration)
Initiator bus grant (arbitration)
Initialization device select
Interrupt (active low)
PGNTX
PIDSEL
Y8
PCI
PCI
I
PINTA
Y9
O
TOTAL PINS
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Pin Descriptions Grouped by Function
43
Serial Interface Signals
The Serial interface is a bidirectional two-wire serial bus. It can use one of the following
formats:
• An 8bit data format followed by an acknowledge bit, which supports transfers at up to
400kbps (low speed).
• A 16bit IEEE 802.3 MDIO data format with 10bits of addressing, which supports
transfers up to 25MHz (high speed).
The signals and pins are identical for both the high and low speed protocols.
Which of the two data rates used is selected by the state of the PROM interface’s SPLD
signal that is asserted while the PROM interface is idle. When SPLD is asserted HI the low
speed serial bus protocol is selected and when SPLD is asserted LOW the MDIO protocol is
selected.
The bus only supports a single master hierarchy that can operate as either a receiver or a
transmitter.
Both SIDA and SICL are bidirectional lines that are connected, through a pull-up resistor, to
a positive supply voltage. When the bus is free, both lines are HIGH. The output stages of
the devices connected to the bus must have either an open-drain or open-collector in
order to perform the wired-AND function required for its arbitration mechanism.
Table 16 Serial Interface Signals
SIGNAL NAME
SICL
PIN #
Y5
TOTAL TYPE
I/O
SIGNAL DESCRIPTION
1
1
2
LVTTL IPD/O Serial Clock line
LVTTL IPD/O Serial Data line
SIDA
Y6
TOTAL PINS
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
44
CHAPTER 2: SIGNAL DESCRIPTIONS
PROM Interface Signals
The PROM interface is a low speed I/O port that allows the C-5e NP to communicate
through external logic to PROM. The PROM clock is 1/2 to 1/16 the core clock rate. The
maximum PROM size addressable is 4MBytes, and must use a “by 16” part. The PROM
signals are listed in Table 17.
Table 17 PROM Interface Signals
SIGNAL
NAME
SPDO
SPDI
PIN #
Y1
TOTAL TYPE
I/O
SIGNAL DESCRIPTION
Serial Data Out
Serial Data In
1
1
1
LVTTL
O
Y2
LVTTL IPD
LVTTL O
SPLD
Y3
When load is asserted on a positive clock
edge, the external logic performs a parallel
load. On each positive clock edge when
load is de-asserted, the shift registers shift.
When the PROM interface is idle:
• If SPLD is asserted HI it indicates low
speed serial protocol,
• If asserted LOW it indicates MDIO serial
protocol.
SPCK
Y4
1
LVTTL
O
Clock
4
TOTAL PINS
Figure 5 shows the connections between the PROM Interface and external board logic.
The application is required to provide an external shift register with parallel-in and
parallel-out capabilities, and a parallel load register. Both devices should be
positive-edge-triggered and perform a parallel load whenever SPLD is asserted. When
SPLD is deasserted the shift register shifts.
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Pin Descriptions Grouped by Function
45
Figure 5 PROM Interface Diagram
C-5e Network Proc0essor External Logic
21
PROM_ADDR<21:1>
CE
SPDO
SPDI
21
6
1
0
21
21
6 0
Internal Shift
Register
External Shift
Register
0
15
21
PROM_ADDR<21:1>
21
CE
31
16 15
0
PROM _H_Word
PROM _LO_Word
1
16
PROM _Return_Data
PROM Clock Gen.
PROM Sequencer
PROM
SPCLK
SPLD
PROM_Data
The PROM interface operates in the following manner (Note that two accesses are
piplined together to execute one 32-bit fetch). The steps are shown in Figure 6.
1
2
3
The PROM_ADDR is loaded into the network processor internal shift register.
The PROM_ADDR is shifted into the external shift register for 22 SPCLK cycles.
SPLD is asserted for one SPCLK cycle, loading the PROM_ADDR into the external
presentation register.
4
5
6
7
SPLD is deasserted for 22 SPCLK cycles. The PROM presents the first 16bit PROM_DATA.
At the same time, the next PROM_ADDR is shifted into the external shift register.
SPLD is asserted for one SPCLK cycle, loading the PROM_ADDR into the external
presentation register and the first PROM_DATA into the external shift register.
SPLD is deasserted for 22 SPCLK cycles, shifting the first PROM_DATA into the network
processor internal shift register.
SPLD is asserted for one SPCLK cycle, loading the first PROM_DATA into the network
processor PROM_RETURN_DATA register and the second PROM_DATA into the
external shift register.
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
46
CHAPTER 2: SIGNAL DESCRIPTIONS
8
9
SPLD is deasserted for 22 SPCLK cycles, shifting the second PROM_DATA into the
network processor internal shift register.
SPLD is asserted for one SPCLK cycle, loading the second PROM_DATA into the
network processor PROM_RETURN_DATA register.
Figure 6 PROM Interface Timing Outline
XP PROM Interface outline
`
`
`
`
`
SPLD
A1
A2
A3
A4
A5
SPDTO
D1
D2
D3
SPDTI
XP PROM Interface detail
14 15 16 17 18 19 20 21 22 23
1
2
3
4
5
6
7
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
1
2
3
4
5
6
7
8
9
10 11 12 13
SPCLK
SPLD
A1
A2
A3
A4
A
A
A
A
A
A
A
A
A
A
A
A
21 20 19 18 17 16 15 14 13 12 11 10
A
9
A
8
A
7
A
6
A
5
A
4
A
3
A
2
A
CE
1
x
SPDTO
The PROM_ADDR is loaded into the
C-5's internal shift register.
1
3
5
The PROM_ADDR is shifted into
the external shift register.
The PROM_ADDR is loaded into the
external presentation register.
2
(SPCLK Rising Edge used for shifting)
4
The PROM_DATA is
presenting.
The PROM_DATA is loaded into the
external shift register.
D1
D2
D
D D
15 14 13 12 11 10
D
D
D
D
9
D
8
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
x
x
x
x
x
x
x
SPDTI
The PROM_DATA is shifted into the C-5's
Internal shift register.
6
8
The PROM_DATA is loaded into the C-5's
internal PROM_RETURN_DATA register.
7
9
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Pin Descriptions Grouped by Function
47
General System Interface Signal
Table 18 provides the signal for the Executive Processor reset power status and I/O clock.
The C-5e NP can be powered up with the XP either running or with the XP in reset mode
similar to the CPs. When the XP remains in reset mode, an external host can be used to
control the initialization of the C-5e NP.
Table 18 General System Interface Signal
SIGNAL NAME
PIN #
TOTAL TYPE
I/O
SIGNAL DESCRIPTION
XPUHOT
W8
1
LVTTL IPD
Sample at Power On Reset determines if the XP RISC Core is held in reset. Low
equals reset and High equals active. During normal operation, this is an
external interrupt, triggered asynchronously on the rising edge of XPUHOT.
1
TOTAL PINS
Fabric Processor Interface The FP has logical signal interfaces: a receive data interface and a transmit data interface,
Signals
each with its own control, data, and clock signals. The interface has the following
characteristics:
• The interface clocks, FRXCLK and FTXCLK can have a different frequency from the core
C-5e NP clock frequency. The FP supports a fabric interface frequency from 10MHz to
125MHz.
• FRXCLK and FTXCLK can be independent of each other; typically they have the same
frequency, but are allowed to be skewed relative to each other.
• Each data bus can be configured for widths of 8 (data bits 7:0 are used), 16 (bits 15:0),
or 32 (bits 31:0). In 8bit mode, data bits 31:8 are unused. In 16bit mode, data bits 31:16
are unused.
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
48
CHAPTER 2: SIGNAL DESCRIPTIONS
Table 19 Fabric Interface Signals
SIGNAL NAME
PIN #
TOTAL TYPE
I/O
SIGNAL DESCRIPTION
FIN0 - FIN31
AE12, AD12, AC12, AJ11, AH11, AG11,AF11,
AE11, AD11, AC11, AJ10, AG10, AF10, AD10,
AC10, AJ9, AH9, AG9, AF9, AE9, AD9, AC9, AJ8,
AH8, AG8, AF8, AE8, AD8, AC8, AJ7, AH7, AG7
32
LVTTL
IPD
Fabric Data Bus In
FOUT0 - FOUT31
AJ18, AH18, AG18, AE18, AD18, AC18, AJ17,
AH17, AF17, AE17, AD17, AC17, AJ16, AH16,
AG16, AF16, AE16, AD16, AC16, AJ15, AG15,
AF15, AD15, AC15, AJ14, AH14, AG14, AF14,
AE14, AD14, AC14, AJ13
32
LVTTL
O
Fabric Data Bus Out
FRXCLK
AC6
1
LVTTL
LVTTL
LVTTL
LVTTL
IPD
IPD
Receive Clock
Transmit Clock
FTXCLK
AG12
1
FRXCTL0 - FRXCTL6
FTXCTL0 - FTXCTL6
TOTAL PINS
AE7, AD7, AC7, AJ6, AG6, AF6, AD6
AH13, AF13, AE13, AD13, AC13, AJ12, AH12
7
IPD, O Receive Control Signals
IPD, O Transmit Control Signals
7
80
The following tables list the Fabric Interface pin mappings:
• Utopia1, Utopia2, Utopia3 ATM Mode mappings are listed in Table 20
• Utopia1, Utopia2, Utopia3 PHY Mode mappings are listed in Table 21
• PRIZMA Mode mappings are listed in Table 22 (PRIZMA protocol is a subset of Utopia3
PHY)
• Power X(CSIX-L0) Mode mappings are listed in Table 23
• CSIX-L1 Mode mappings are listed in Table 24
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Pin Descriptions Grouped by Function
49
Table 20 Utopia1*, 2*, 3 ATM Mode, C-5e Network Processor to Fabric Interface Pin Mapping
RECEIVE SIGNALS
TRANSMIT SIGNALS
C-5e NETWORK
PROCESSOR
C-5e NETWORK
PROCESSOR
I/O
UTOPIA
NOTE
I/O
UTOPIA
NOTE
FRXCTL0
Output
RxEnb*
Pullup or No
Connection
FTXCTL0
Output
TxEnb*
Pullup or No
Connection
FRXCTL1
FRXCTL2
FRXCTL3
FRXCTL4
FRXCTL5
FRXCTL6
Input
Input
Input
Input
Input
Input
RxClav
RxSOC
n/a
FTXCTL1
FTXCTL2
FTXCTL3
FTXCTL4
FTXCTL5
FTXCTL6
Input
TxClav
TxSOC
n/a
Output
Input
n/a
Input
n/a
n/a
Input
n/a
RxPrty
Output
TxPrty
*
Cell size must be 4Byte aligned. Both RxEnb and TxEnb are Active Low.
Table 21 Utopia1*, 2*, 3 PHY Mode, C-5e Network Processor to Fabric Interface Pin Mapping
RECEIVE SIGNALS
TRANSMIT SIGNALS
C-5e NETWORK
PROCESSOR
C-5e NETWORK
PROCESSOR
I/O
UTOPIA
TxEnb*
TxClav
TxSOC
n/a
NOTE
I/O
UTOPIA
RxEnb*
RxClav
RxSOC
n/a
NOTE
FRXCTL0
FRXCTL1
FRXCTL2
FRXCTL3
FRXCTL4
FRXCTL5
FRXCTL6
Input
Output
Input
Input
Input
Input
Input
Pullup
FTXCTL0
Input
Output
Output
Input
Input
Input
Output
Pullup
No Connection FTXCTL1
FTXCTL2
No Connection
FTXCTL3
n/a
FTXCTL4
n/a
n/a
FTXCTL5
n/a
TxPrty
FTXCTL6
RxPrty
*
Cell size must be 4Byte aligned. Both TxEnb and RxEnb are Active Low.
When configuring two C-5e network processors back-to-back using the Fabric Port, set
up the transmit side of each C-5e network processor in Utopia ATM mode and the receive
side of each C-5e network processor in Utopia PHY mode.
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
50
CHAPTER 2: SIGNAL DESCRIPTIONS
Table 22 PRIZMA Mode, C-5e Network Processor to Fabric Interface Pin Mapping
RECEIVE SIGNALS
TRANSMIT SIGNALS
C-5e NETWORK
PROCESSOR
C-5e NETWORK
PROCESSOR
I/O
UTOPIA
NOTE
I/O
UTOPIA
NOTE
FRXCTL0
Input
TxEnb*
Not connected to FTXCTL0
fabric.
Input
RxEnb*
Not connected to
fabric.
FRXCTL1
FRXCTL2
FRXCTL3
FRXCTL4
FRXCTL5
FRXCTL6
Output
Input
Input
Input
Input
Input
TxClav
TxSOP
n/a
No connection
FTXCTL1
FTXCTL2
FTXCTL3
FTXCTL4
FTXCTL5
FTXCTL6
Output
Output
Input
RxClav
RxSOP
n/a
No Connection
n/a
Input
n/a
n/a
Input
n/a
TxPrty
Optional
Output
RxPrty
Optional
*
Both TxEnb and RxEnb are Active Low.
Table 23 Power X(CSIX-L0) Mode, C-5e Network Processor to Fabric Interface Pin Mapping
RECEIVE SIGNALS
TRANSMIT SIGNALS
C-5e NETWORK
PROCESSOR
C-5e NETWORK
PROCESSOR
I/O
POWER X
RxCtrl[0]
RxCtrl[1]
RxCtrl[2]
RxPrty[3]
RxPrty[2]
RxPrty[1]
RxPrty[0]
NOTE
I/O
POWER X
TxCtrl[0]
TxCtrl[1]
TxCtrl[2]
TxPrty[3]
TxPrty[2]
TxPrty[1]
TxPrty[0]
NOTE
FRXCTL0
FRXCTL1
FRXCTL2
FRXCTL3
FRXCTL4
FRXCTL5
FRXCTL6
Input
Input
Input
Input
Input
Input
Input
FTXCTL0
FTXCTL1
FTXCTL2
FTXCTL3
FTXCTL4
FTXCTL5
FTXCTL6
Output
Output
Output
Output
Output
Output
Output
For the CSIX-L1 Mode, VDDF= 2.5V.
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Pin Descriptions Grouped by Function
51
Table 24 CSIX-L1 Mode, C-5e Network to Fabric Interface Pin Mapping
FPRX SIGNALS
FPTX SIGNALS
C-5E NP
FRxCTL0
FRxCTL1
FRxCTL2
FRxCTL3
FRxCTL4
FRxCTL5
FRxCTL6
I/O
CSIX-L1
n/a
NOTE
C-5E NP
FTxCTL0
FTxCTL1
FTxCTL2
FTxCTL3
FTxCTL4
FTxCTL5
FTxCTL6
I/O
CSIX-L1
n/a
NOTE
Input
Input
Input
Input
Input
Input
Input
Input
Input
Output
Input
Input
Input
Output
n/a
n/a
TxSOF
n/a
RxSOF
n/a
n/a
n/a
n/a
n/a
TxPrty
RxPrty
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
52
CHAPTER 2: SIGNAL DESCRIPTIONS
BMU SDRAM Interface The BMU and SDRAM interface signals are described in Table 25.
Signals
The BMU is designed to support SDRAM devices with 12 address lines. All 139 data lines
and all 12 address lines must be connected to the SDRAM in order for the BMU to be able
to read and write external SDRAM properly.
Table 25 BMU SDRAM Interface Signals
SIGNAL NAME
PIN #
TOTAL TYPE
I/O
SIGNAL DESCRIPTION
MD0 - MD129
U23, U22, U21, T29, T28, T27, T26,
T25, T24, T23, T22, T21, R29, R28,
R27, R26, R25, R24, R23, R22, R21,
P29, P28, P26, P25, P24, P22, P21,
N29, N27, N26, N25, N23, N22, N21,
M29, M28, M27, M26, M25, M24,
M23, M22, M21, L29, L28, L27, L26,
L25, L24, L23, L22, L21, K29, K28,
K26, K25, K24, K22, K21, J29, J27,
J26, J25, J23, J22, J21, H29, H28,
H27, H26, H25, H24, H23, H22, H21,
G29, G28, G27, G26, G25, G24, G23,
G22, G21, F29, F28, F26, F25, F24,
F22, F21, E29, E27, E26, E25, E23,
E22, E21, D29, D28, D27, D26, D25,
D24, D23, D22, D21, C29, C28, C26,
C25, C24, C22, C21, B29, B27, B26,
B25, B23, B22, B21, A29, A28, A27,
A26, A25, A24, A23, A22
130
LVTTL
IPD/O Data Lines
MDECC0 - MDECC8 E19, F19, G19, A20, C20, D20, F20,
G20, A21
9
LVTTL
LVTTL
IPD/O Stored as data, ECC bits
MA0 - MA11
B16, C16, D16, E16, F16, G16, A17, 12
B17, D17, E17, F17, G17
OPD Address Outputs: A0-A11 are sampled during the
ACTIVE command and READ/WRITE to select one
location out of the memory array in the respective
bank. The address inputs also provide the
op-code during a LOAD MODE REGISTER
command
MBA0 - MBA1
MCASX
E18, C18
D19
2
1
LVTTL
LVTTL
OPD Bank Address Outputs: BA0 and BA1 define which
bank the ACTIVE, READ, WRITE or PRECHARGE
command is being applied
OPD Command Outputs: MRASX, MCASX, MWEX and
MCSX define the command being entered.
NOTE: MCSX is considered part of the command
code.
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Pin Descriptions Grouped by Function
53
Table 25 BMU SDRAM Interface Signals (continued)
SIGNAL NAME
PIN #
TOTAL TYPE
I/O
SIGNAL DESCRIPTION
MRASX
C19
1
1
1
LVTTL
LVTTL
LVTTL
OPD Command Outputs: MRASX, MCASX, MWEX and
MCSX define the command being entered. MCSX
is considered part of the command code.
MWEX
MCSX
B19
A19
OPD Command Outputs: MRASX, MCASX, MWEX and
MCSX define the command being entered. MCSX
is considered part of the command code.
OPD Chip Select: MCSX enables (registered LOW) and
disables (registered HIGH) the command decoder.
All commands are masked when MCSX is
registered HIGH. MCSX provides the external bank
selection on systems with multiple banks. MCSX is
considered part of the command code.
MDQM
MDQML
G18
F18
1
1
LVTTL
LVTTL
OPD Input/Output Mask: MDQM is an input mask
signal for write accesses and an output enable
OPD
signal for read accesses. Input data is masked
when MDQM is sampled HIGH during a WRITE
cycle. The output buffers are placed in a high Z
state (two-clock latency) when MDQM is sampled
HIGH during the READ cycle.
NOTE: MDQML is an identical copy of MDQM
used to drive the loading on SDRAM
configurations with 2 DQM pins.
MDCLK
B18
1
LVTTL
IPD
Clock: MDCLK is driven by the system clock. All
SDRAM input signals are sampled on the positive
edge of the MDCLK. MDCLK also increments the
internal burst counter and controls the output
registers.
160
TOTAL PINS
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
54
CHAPTER 2: SIGNAL DESCRIPTIONS
TLU SRAM Interface The TLU SRAM interface supports up to 128MBytes of SRAM at frequencies to 133MHz
Signals
using LVTTL signaling levels (in single bank-mode only) and SRAM technologies up to
64Mbits. The TLU SRAM interface signals are described in Table 26.
Table 26 TLU SRAM Interface Signals
SIGNAL NAME
PIN #
TOTAL TYPE
I/O
SIGNAL DESCRIPTION
TD0 - TD63
G6, G7, G8, G9, G10, H1, H2, H3, H4, H5, H6, H7, H8, 64
H9, J1, J3, J4, J5, J7, J8, J9, K1, K2, K4, K5, K6, K8, K9,
L1, L2, L3, L4, L5, L6, L7, L8, L9, M1, M2, M3, M4,
M5, M6, M7, M8, M9, N1, N3, N4, N5, N7, N8, N9,
P1, P2, P4, P5, P6, P8, P9, R6, R7, R8, R9
LVTTL IPD/O TLU Memory Data
TA0 - TA21
T1, U1, U3, U4, U5, U7, U8, U9, V1, V2, V4, V5, V6, 22
V8, V9, W1, W2, W3, W4, W5, W6, W7
LVTTL OPD TLU Memory Address
TPAR0 - TPAR3
R2, R3, R4, R5
4
LVTTL IPD/O Word Data Parity (i.e. TPAR0 across
TD15:0)
TCE0X - TCE3X
TWE0X - TWE3X
TCLKI
T2, T3, T4, T5
T6, T7, T8, T9
R1
4
LVTTL OPD TLU Memory Chip Enable
LVTTL OPD TLU Memory Write Enable
4
1
LVTTL IPD
TLU Clock Input
99
TOTAL PINS
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Pin Descriptions Grouped by Function
55
QMU SRAM (Internal The QMU signals are described in Table 27.
Mode) Interface Signals
Table 27 QMU SRAM (Internal Mode) Interface Signals
SIGNAL NAME
PIN #
TOTAL TYPE
I/O
SIGNAL DESCRIPTION
QA0 - QA16
C8, B8, A8, F9, E9, D9, C9, B9, A9, F10, D10, C10,
A10, G11, F11, E11, D11
17
LVTTL
O
Address [16:0]
QD0 - QD31
G1, F1, E1, D1, C1, B1, G2, F2, D2, C2, A2, G3, E3,
D3, B3, A3, G4, F4, E4, D4, C4, B4, A4, G5, F5, E5,
D5, C5, B5, A5, F6, D6
32
LVTTL IPD/O Data
QDQPAR
QARDY
QNQRDY
QWEX
C11
E8
1
1
1
1
1
1
1
1
LVTTL IPD
LVTTL IPD
LVTTL IPD
nc
nc
D8
C6
A6
E7
nc
LVTTL
LVTTL
O
O
Write Enable
QBCLKO
QBCLKI
QACLKO
QACLKI
nc
nc
nc
LVTTL IPD
LVTTL
LVTTL IPD
D7
B7
O
Input Clock (drives QMU and
external SRAM)
QDPL
A7
F8
1
LVTTL IPD/O Data Parity Low
LVTTL IPD/O Data Parity High
QDPH
1
59
TOTAL PINS
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
56
CHAPTER 2: SIGNAL DESCRIPTIONS
QMU to Q-5 TMC (External The QMU to Q-5 Traffic Management Coprocessor (TMC) signals are described in Table 28.
Mode) Interface Signals
Table 28 QMU to Q-5 TMC (External Mode) Interface Signals
SIGNAL NAME
PIN #
TOTAL TYPE
I/O
SIGNAL DESCRIPTION
QA0 - QA15
C8, B8, A8, F9, E9, D9, C9, B9, A9, F10, D10,
C10, A10, G11, F11, E11
16
LVTTL
O
Enqueue Data [8:23]
QA16
D11
1
LVTTL
O
Enqueue Parity
QD0 - QD23
G1, F1, E1, D1, C1, B1, G2, F2, D2, C2, A2, G3, 24
E3, D3, B3, A3, G4, F4, E4, D4, C4, B4, A4, G5
LVTTL IPD
Dequeue Data [0:23]
QD24 - QD31
QDQPAR
QARDY
F5, E5, D5, C5, B5, A5, F6, D6
8
1
1
1
1
1
1
1
1
1
1
59
LVTTL IPD
LVTTL IPD
Enqueue Data [0:7]
Dequeue Parity
Dequeue Ack Ready
Enqueue Ready
Dequeue Ready
Output ClockB
Input ClockB
C11
E8
LVTTL
LVTTL
LVTTL
LVTTL
IPD
IPD
QNQRDY
QWEX
D8
C6
A6
E7
O
QBCLKO
QBCLKI
O
LVTTL IPD
LVTTL
LVTTL IPD
QACLKO
QACLKI
D7
B7
A7
F8
O
Output ClockA
Input ClockA
QDPL
LVTTL
LVTTL
O
O
Dequeue Ack [0]
Dequeue Ack [1]
QDPH
TOTAL PINS
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Pin Descriptions Grouped by Function
57
Power Supply Signals Power supply and ground signals are described in Table 29.
Table 29 Power Supply Signals
SIGNAL NAME
PIN #
TOTAL
TYPE
SIGNAL DESCRIPTION
VDD
J13, J15, J17, J19, K12, K14, K16, K18, L11, L13, L15, 57
L17, L19, M12, M14, M16, M18, N13, N15, N17, N19,
P12, P14, P16, P18, R11, R13, R15, R17, R19, T12, T14,
T16, T18, U11, U13, U15, U17, U19, V12, V14, V16,
V18, W11, W13, W15, W17, W19, Y12, Y14, Y16, Y18,
AA11, AA13, AA15, AA17, AA19,
P
Core Supply Voltage (1.25V Input)
VDD33
GND
B20, B28, C13, C17, C23, E15, F23, F27, H12, H14,
H16, H18, H20, J28, K20, K23, M20, N24, P20, P27,
T20, U28, V20, V23, Y20, AA6, AA24, AB3, AB10,
AB18, AB20, AB27, AE24, AF3, AF27, AH2, AH20,
AH28
38
P
P
I/O Supply Voltage (3.3V Input)
B6, B15, B24, C3, C27, D12, D18, E2, E6, E10, E20, E24, 122
E28, H11, H13, H15, H17, H19, J6, J10, J12, J14, J16,
J18, J20, J24, K3, K11, K13, K15, K17, K19, K27, L10,
L12, L14, L16, L18, L20, M11, M13, M15, M17, M19,
N2, N10, N12, N14, N16, N18, N20, N28, P7, P11, P13,
P15, P17, P19, P23, R10, R12, R14, R16, R18, R20, T11,
T13, T15, T17, T19, U6, U10, U12, U14, U16, U18, U20,
U24, V3, V11, V13, V15, V17, V19, V27, W10, W12,
W14, W16, W18, W20, Y11, Y13, Y15, Y17, Y19, AA2,
AA10, AA12, AA14, AA16, AA18, AA20, AA28, AB7,
AB11, AB13, AB15, AB17, AB19, AB23, AE2, AE10,
AE20, AE28, AF7, AF12, AF18, AF23, AH6, AH15,
AH24
Ground
VDDF
VDDT
AB12, AB14, AB16, AE6, AE15, AG13, AG17, AH10
8
P
P
Fabric I/O supply (3.3 or 2.5V)
TLU and QMU I/O supply (3.3V)
B2, B10, C7, F3, F7, H10, J2, J11, K7, K10, M10, N6,
N11, P3, P10, T10, U2, V7, V10, Y10
20
245
TOTAL PINS
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
58
CHAPTER 2: SIGNAL DESCRIPTIONS
Test Signals Test signals are described in Table 30.
Table 30 Miscellaneous Test Signals For JTAG, Scan, and Internal Test Routines
SIGNAL NAME
JTCK
PIN #
C15
TOTAL TYPE
I/O
SIGNAL DESCRIPTION
1
1
LVTTL IPD
LVTTL IPD
Test Clock
JTMS
A14
Test Mode Select. High selects modes
as defined in the IEEE 1149.1 JTAG
specification.
JTRSTX†
JTDI†
A12
B14
A13
B13
C14
1
1
1
1
1
LVTTL IPD
LVTTL IPD
Test Reset (low active)
Test Data In
JTDO
LVTTL
O
Test Data Out
JHIGHZ
JCLKBYP
LVTTL IPD
LVTTL IPD
Turns off all output drivers when High
1X or 2X Clock Mode Select. Low
selects 1X, High selects 2X. Motorola
recommends using 1X mode
(pulldown or leave JCLKBYP
unconnected).
JSE
D15
1
LVTTL IPD
Scan Enable. High enables scan test.
Scan Out Pins
JS00-JS05
TOTAL PINS
D14, A16, D13, C12, A15, B12
6
LVTTL
O
14
During JTAG, SCLK and SCLKX must remain as differential inputs.
No Connection Pins No connection pins are listed in Table 31.
Table 31 No Connection Pins
SIGNAL NAME
PIN #
B11, A11, A18
TOTAL TYPE
I/O
SIGNAL DESCRIPTION
NC3 - NC5
3
nc
IPD/O Reserved for future functionality
3
TOTAL PINS
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Signals Grouped by Pin Number
59
Signals Grouped by Pin
Number
The C-5e NP signals are listed by pin number in Table 32.
Table 32 Signals Listed by Pin Number
PIN
FUNCTION
PIN
FUNCTION
PIN
A 1-29
FUNCTION
PIN
FUNCTION
A1
A2
A3
A4
A5
A6
A7
A8
Not present A9
QA8
A17
A18
A19
A20
A21
A22
A23
A24
MA6
A25
A26
A27
A28
A29
MD126
MD125
MD124
MD123
MD122
QD10
QD15
QD22
QD29
QBCLKO
QDPL
QA2
A10
QA12
NC4
NC5
A11
A12
A13
A14
A15
A16
MCSX
JTRSTX
JTDO
JTMS
JSO4
JSO1
MDECC3
MDECC8
MD129
MD128
MD127
B 1-29
B1
B2
B3
B4
B5
B6
B7
B8
QD5
B9
QA7
B17
B18
B19
B20
B21
B22
B23
B24
MA7
B25
B26
B27
B28
B29
MD118
MD117
MD116
VDD33
MD115
VDDT
QD14
QD21
QD28
GND
B10
B11
B12
B13
B14
B15
B16
VDDT
NC3
MDCLK
MWEX
VDD33
MD121
MD120
MD119
GND
JSO5
JHIGHZ
JTDI
QACLKI
QA1
GND
MA0
C 1-29
C1
C2
C3
C4
C5
C6
C7
C8
QD4
C9
QA6
C17
C18
C19
C20
C21
C22
C23
C24
VDD33
MBA1
C25
C26
C27
C28
C29
MD111
MD110
GND
QD9
C10
C11
C12
C13
C14
C15
C16
QA11
QDQPAR
JSO3
GND
QD20
QD27
QWEX
VDDT
QA0
MRASX
MDECC4
MD114
MD113
VDD33
MD112
MD109
MD108
VDD33
JCLKBYP
JTCK
MA1
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
60
CHAPTER 2: SIGNAL DESCRIPTIONS
Table 32 Signals Listed by Pin Number (continued)
PIN
FUNCTION
PIN
FUNCTION
PIN
D 1-29
FUNCTION
PIN
FUNCTION
D1
D2
D3
D4
D5
D6
D7
D8
QD3
D9
QA5
D17
D18
D19
D20
D21
D22
D23
D24
MA8
D25
D26
D27
D28
D29
MD103
MD102
MD101
MD100
MD99
QD8
D10
D11
D12
D13
D14
D15
D16
QA10
QA16
GND
JSO2
JSO0
JSE
GND
QD13
QD19
QD26
QD31
QACLKO
QNQRDY
MCASX
MDECC5
MD107
MD106
MD105
MD104
MA2
E 1-29
E1
E2
E3
E4
E5
E6
E7
E8
QD2
E9
QA4
E17
E18
E19
E20
E21
E22
E23
E24
MA9
E25
E26
E27
E28
E29
MD95
MD94
MD93
GND
GND
E10
E11
E12
E13
E14
E15
E16
GND
MBA0
MDECC0
GND
QD12
QD18
QD25
GND
QA15
CCLK7
CCLK5
CCLK2
VDD33
MA3
MD98
MD97
MD96
GND
MD92
QBCLKI
QARDY
F 1-29
F1
F2
F3
F4
F5
F6
F7
F8
QD1
F9
QA3
F17
F18
F19
F20
F21
F22
F23
F24
MA10
F25
F26
F27
F28
F29
MD88
MD87
VDD33
MD86
MD85
QD7
F10
F11
F12
F13
F14
F15
F16
QA9
MDQML
MDECC1
MDECC6
MD91
VDDT
QD17
QD24
QD30
VDDT
QDPH
QA14
CCLK6
CCLK4
CCLK1
SCLKX
MA4
MD90
VDD33
MD89
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Signals Grouped by Pin Number
61
Table 32 Signals Listed by Pin Number (continued)
PIN
FUNCTION
PIN
FUNCTION
PIN
G 1-29
FUNCTION
PIN
FUNCTION
G1
G2
G3
G4
G5
G6
G7
G8
QD0
QD6
QD11
QD16
QD23
TD0
G9
TD3
G17
G18
G19
G20
G21
G22
G23
G24
MA11
G25
G26
G27
G28
G29
MD80
MD79
MD78
MD77
MD76
G10
G11
G12
G13
G14
G15
G16
TD4
MDQM
MDECC2
MDECC7
MD84
QA13
CPREF
CCLK3
CCLK0
SCLK
MA5
MD83
TD1
MD82
TD2
MD81
H 1-29
H1
H2
H3
H4
H5
H6
H7
H8
TD5
H9
TD13
VDDT
GND
H17
H18
H19
H20
H21
H22
H23
H24
GND
H25
H26
H27
H28
H29
MD71
MD70
MD69
MD68
MD67
TD6
H10
H11
H12
H13
H14
H15
H16
VDD33
GND
TD7
TD8
VDD33
GND
VDD33
MD75
MD74
MD73
MD72
TD9
TD10
TD11
TD12
VDD33
GND
VDD33
J 1-29
J1
J2
J3
J4
J5
J6
J7
J8
TD14
VDDT
TD15
TD16
TD17
GND
J9
TD20
GND
VDDT
GND
VDD
GND
VDD
GND
J17
J18
J19
J20
J21
J22
J23
J24
VDD
J25
J26
J27
J28
J29
MD63
MD62
MD61
VDD33
MD60
J10
J11
J12
J13
J14
J15
J16
GND
VDD
GND
MD66
MD65
MD64
GND
TD18
TD19
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
62
CHAPTER 2: SIGNAL DESCRIPTIONS
Table 32 Signals Listed by Pin Number (continued)
PIN
FUNCTION
PIN
FUNCTION
PIN
K 1-29
FUNCTION
PIN
FUNCTION
K1
K2
K3
K4
K5
K6
K7
K8
TD21
TD22
GND
K9
TD27
VDDT
GND
VDD
GND
VDD
GND
VDD
K17
K18
K19
K20
K21
K22
K23
K24
GND
K25
K26
K27
K28
K29
MD56
MD55
GND
K10
K11
K12
K13
K14
K15
K16
VDD
GND
TD23
TD24
TD25
VDDT
TD26
VDD33
MD59
MD58
VDD33
MD57
MD54
MD53
L 1-29
L1
L2
L3
L4
L5
L6
L7
L8
TD28
TD29
TD30
TD31
TD32
TD33
TD34
TD35
L9
TD36
GND
VDD
GND
VDD
GND
VDD
GND
L17
L18
L19
L20
L21
L22
L23
L24
VDD
L25
L26
L27
L28
L29
MD48
MD47
MD46
MD45
MD44
L10
L11
L12
L13
L14
L15
L16
GND
VDD
GND
MD52
MD51
MD50
MD49
M 1-29
M1
M2
M3
M4
M5
M6
M7
M8
TD37
TD38
TD39
TD40
TD41
TD42
TD43
TD44
M9
TD45
VDDT
GND
VDD
GND
VDD
GND
VDD
M17
M18
M19
M20
M21
M22
M23
M24
GND
M25
M26
M27
M28
M29
MD39
MD38
MD37
MD36
MD35
M10
M11
M12
M13
M14
M15
M16
VDD
GND
VDD33
MD43
MD42
MD41
MD40
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Signals Grouped by Pin Number
63
Table 32 Signals Listed by Pin Number (continued)
PIN
FUNCTION
PIN
FUNCTION
PIN
N 1-29
FUNCTION
PIN
FUNCTION
N1
N2
N3
N4
N5
N6
N7
N8
TD46
GND
N9
TD52
GND
VDDT
GND
VDD
GND
VDD
GND
N17
N18
N19
N20
N21
N22
N23
N24
VDD
N25
N26
N27
N28
N29
MD31
MD30
MD29
GND
N10
N11
N12
N13
N14
N15
N16
GND
TD47
TD48
TD49
VDDT
TD50
TD51
VDD
GND
MD34
MD33
MD32
VDD33
MD28
P 1-29
P1
P2
P3
P4
P5
P6
P7
P8
TD53
TD54
VDDT
TD55
TD56
TD57
GND
P9
TD59
VDDT
GND
VDD
GND
VDD
GND
VDD
P17
P18
P19
P20
P21
P22
P23
P24
GND
P25
P26
P27
P28
P29
MD24
MD23
VDD33
MD22
MD21
P10
P11
P12
P13
P14
P15
P16
VDD
GND
VDD33
MD27
MD26
GND
TD58
MD25
R 1-29
R1
R2
R3
R4
R5
R6
R7
R8
TCLKI
TPAR0
TPAR1
TPAR2
TPAR3
TD60
R9
TD63
GND
VDD
GND
VDD
GND
VDD
GND
R17
R18
R19
R20
R21
R22
R23
R24
VDD
R25
R26
R27
R28
R29
MD16
MD15
MD14
MD13
MD12
R10
R11
R12
R13
R14
R15
R16
GND
VDD
GND
MD20
MD19
MD18
MD17
TD61
TD62
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
64
CHAPTER 2: SIGNAL DESCRIPTIONS
Table 32 Signals Listed by Pin Number (continued)
PIN
FUNCTION
PIN
FUNCTION
PIN
T 1-29
FUNCTION
PIN
FUNCTION
T1
T2
T3
T4
T5
T6
T7
T8
TA0
T9
TWE3X
VDDT
GND
VDD
T17
T18
T19
T20
T21
T22
T23
T24
GND
T25
T26
T27
T28
T29
MD7
MD6
MD5
MD4
MD3
TCE0X
TCE1X
TCE2X
TCE3X
TWE0X
TWE1X
TWE2X
T10
T11
T12
T13
T14
T15
T16
VDD
GND
VDD33
MD11
MD10
MD9
GND
VDD
GND
VDD
MD8
U 1-29
U1
U2
U3
U4
U5
U6
U7
U8
TA1
U9
TA7
U17
U18
U19
U20
U21
U22
U23
U24
VDD
GND
VDD
GND
MD2
MD1
MD0
GND
U25
U26
U27
U28
U29
CPF_6
CPF_5
CPF_4
VDD33
CPF_3
VDDT
TA2
U10
U11
U12
U13
U14
U15
U16
GND
VDD
GND
VDD
GND
VDD
GND
TA3
TA4
GND
TA5
TA6
V 1-29
V1
V2
V3
V4
V5
V6
V7
V8
TA8
V9
TA14
VDDT
GND
VDD
GND
VDD
GND
VDD
V17
V18
V19
V20
V21
V22
V23
V24
GND
V25
V26
V27
V28
V29
CPE_6
CPE_5
GND
TA9
V10
V11
V12
V13
V14
V15
V16
VDD
GND
TA10
TA11
TA12
VDDT
TA13
GND
VDD33
CPF_2
CPF_1
VDD33
CPF_0
CPE_4
CPE_3
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Signals Grouped by Pin Number
65
Table 32 Signals Listed by Pin Number (continued)
PIN
FUNCTION
PIN
FUNCTION
PIN
W 1-29
FUNCTION
PIN
FUNCTION
W1
W2
W3
W4
W5
W6
W7
W8
TA15
TA16
TA17
TA18
TA19
TA20
TA21
XPUHOT
W9
PFRAMEX
GND
W17
W18
W19
W20
W21
W22
W23
W24
VDD
W25
W26
W27
W28
W29
CPD_5
CPD_4
CPD_3
CPD_2
CPD_1
W10
W11
W12
W13
W14
W15
W16
GND
VDD
VDD
GND
GND
VDD
CPE_2
CPE_1
CPE_0
CPD_6
GND
VDD
GND
Y 1-29
Y1
Y2
Y3
Y4
Y5
Y6
Y7
Y8
SPDO
SPDI
Y9
PINTA
VDDT
GND
VDD
GND
VDD
GND
VDD
Y17
Y18
GND
Y25
Y26
Y27
Y28
Y29
CPC_3
CPC_2
CPC_1
CPC_0
CPB_6
Y10
Y11
Y12
Y13
Y14
Y15
Y16
VDD
SPLD
SPCK
SICL
Y19
GND
Y20
VDD33
CPD_0
CPC_6
CPC_5
CPC_4
Y21
SIDA
Y22
PGNTX
PIDSEL
Y23
Y24
AA 1-29
AA1
AA2
AA3
AA4
AA5
AA6
AA7
AA8
PSERRX
GND
AA9
PREQX
GND
VDD
GND
VDD
GND
VDD
GND
AA17
VDD
AA25
AA26
AA27
AA28
AA29
CPB_2
CPB_1
CPB_0
GND
AA10
AA11
AA12
AA13
AA14
AA15
AA16
AA18
AA19
AA20
AA21
AA22
AA23
AA24
GND
PPERRX
PDEVSELX
PSTOPX
VDD33
PCLK
VDD
GND
CPB_5
CPB_4
CPB_3
VDD33
CPA_6
PRSTX
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
66
CHAPTER 2: SIGNAL DESCRIPTIONS
Table 32 Signals Listed by Pin Number (continued)
PIN
FUNCTION
PIN
FUNCTION
PIN
FUNCTION
PIN
FUNCTION
AB 1-29
AB1
AB2
AB3
AB4
AB5
AB6
AB7
AB8
PPAR
AB9
PTRDYX
VDD33
GND
AB17
GND
AB25
AB26
AB27
AB28
AB29
CPA_2
CPA_1
VDD33
CPA_0
CP9_6
PCBEX3
VDD33
PCBEX2
PCBEX1
PCBEX0
GND
AB10
AB11
AB12
AB13
AB14
AB15
AB16
AB18
AB19
AB20
AB21
AB22
AB23
AB24
VDD33
GND
VDDF
GND
VDD33
CPA_5
CPA_4
GND
VDDF
GND
PIRDYX
VDDF
CPA_3
AC 1-29
AC1
AC2
AC3
AC4
AC5
AC6
AC7
AC8
PAD31
PAD30
PAD29
PAD28
PAD27
FRXCLK
FRXCTL2
FIN28
AC9
FIN21
AC17
AC18
AC19
AC20
AC21
AC22
AC23
AC24
FOUT11
FOUT5
CP9_5
CP8_5
CP8_0
CP7_0
CP6_0
CP5_1
AC25
AC26
AC27
AC28
AC29
CP4_3
CP3_3
CP2_3
CP1_4
CP0_6
AC10
AC11
AC12
AC13
AC14
AC15
AC16
FIN14
FIN9
FIN2
FTXCTL4
FOUT30
FOUT23
FOUT18
AD 1-29
AD1
AD2
AD3
AD4
AD5
AD6
AD7
AD8
PAD26
PAD25
PAD24
PAD23
PAD22
FRXCTL6
FRXCTL1
FIN27
AD9
FIN20
AD17 FOUT10
AD18 FOUT4
AD19 CP9_4
AD20 CP8_4
AD21 CP7_6
AD22 CP6_6
AD23 CP5_6
AD24 CP5_0
AD25 CP4_2
AD26 CP3_2
AD27 CP2_2
AD28 CP1_3
AD29 CP0_5
AD10 FIN13
AD11 FIN8
AD12 FIN1
AD13 FTXCTL3
AD14 FOUT29
AD15 FOUT22
AD16 FOUT17
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Signals Grouped by Pin Number
67
Table 32 Signals Listed by Pin Number (continued)
PIN
FUNCTION
PIN
FUNCTION
PIN
FUNCTION
PIN
FUNCTION
AE 1-29
AE1
AE2
AE3
AE4
AE5
AE6
AE7
AE8
PAD21
GND
AE9
FIN19
GND
AE17
FOUT9
FOUT3
CP9_3
GND
AE25
AE26
AE27
AE28
AE29
CP4_1
CP3_1
CP2_1
GND
AE10
AE11
AE12
AE13
AE14
AE15
AE16
AE18
AE19
AE20
AE21
AE22
AE23
AE24
PAD20
PAD19
PAD18
VDDF
FIN7
FIN0
FTXCTL2
FOUT28
VDDF
CP7_5
CP6_5
CP5_5
VDD33
CP0_4
FRXCTL0
FIN26
FOUT16
AF 1-29
AF1
AF2
AF3
AF4
AF5
AF6
AF7
AF8
PAD17
PAD16
VDD33
PAD15
PAD14
FRXCTL5
GND
AF9
FIN18
AF17
AF18
AF19
AF20
AF21
AF22
AF23
AF24
FOUT8
GND
AF25
AF26
AF27
AF28
AF29
CP4_0
CP3_0
VDD33
CP1_2
CP0_3
AF10
AF11
AF12
AF13
AF14
AF15
AF16
FIN12
FIN6
CP9_2
CP8_3
CP7_4
CP6_4
GND
GND
FTXCTL1
FOUT27
FOUT21
FOUT15
FIN25
CP4_6
AG 1-29
AG1
AG2
AG3
AG4
AG5
AG6
AG7
AG8
PAD13
PAD12
PAD11
PAD10
PAD9
AG9
FIN17
AG17
AG18
AG19
AG20
AG21
AG22
AG23
AG24
VDDF
AG25
AG26
AG27
AG28
AG29
CP3_6
CP2_6
CP2_0
CP1_1
CP0_2
AG10
AG11
AG12
AG13
AG14
AG15
AG16
FIN11
FOUT2
CP9_1
CP8_2
CP7_3
CP6_3
CP5_4
CP4_5
FIN5
FTXCLK
VDDF
FRXCTL4
FIN31
FOUT26
FOUT20
FOUT14
FIN24
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
68
CHAPTER 2: SIGNAL DESCRIPTIONS
Table 32 Signals Listed by Pin Number (continued)
PIN
FUNCTION
PIN
FUNCTION
PIN
FUNCTION
PIN
FUNCTION
AH 1-29
AH1
AH2
AH3
AH4
AH5
AH6
AH7
AH8
PAD8
VDD33
PAD7
PAD6
PAD5
GND
AH9
FIN16
AH17 FOUT7
AH25 CP3_5
AH26 CP2_5
AH27 CP1_6
AH28 VDD33
AH29 CP0_1
AH10 VDDF
AH11 FIN4
AH18 FOUT1
AH19 CP9_0
AH20 VDD33
AH21 CP7_2
AH22 CP6_2
AH23 CP5_3
AH24 GND
AH12 FTXCTL6
AH13 FTXCTL0
AH14 FOUT25
AH15 GND
FIN30
FIN23
AH16 FOUT13
AJ 1-29
AJ17
AJ1
AJ2
AJ3
AJ4
AJ5
AJ6
AJ7
AJ8
PAD4
AJ9
FIN15
FOUT6
FOUT0
CP8_6
CP8_1
CP7_1
CP6_1
CP5_2
CP4_4
AJ25
AJ26
AJ27
AJ28
AJ29
CP3_4
CP2_4
CP1_5
CP1_0
CP0_0
PAD3
AJ10
AJ11
AJ12
AJ13
AJ14
AJ15
AJ16
FIN10
AJ18
AJ19
AJ20
AJ21
AJ22
AJ23
AJ24
PAD2
FIN3
PAD1
FTXCTL5
FOUT31
FOUT24
FOUT19
FOUT12
PAD0
FRXCTL3
FIN29
FIN22
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
JTAG Support
69
JTAG Support
The C-5e NP contains Joint Test Action Group (JTAG) test logic compliant with the IEEE
1149.1 specification. All required public instructions are implemented, as well as some
optional instructions. This section contains information regarding the pinout, instructions,
identification codes, and boundary scan cell types.
Pinout The C-5e NP uses the standard JTAG pins including the optional test reset pin. Table 30
describes the pins and their functions.
JTAG Data Registers The C-5e NP contains the standard internal registers as specified in IEEE 1149.1. These
registers are described in Table 33.
Table 33 JTAG Internal Register Descriptions
REGISTER NAME
Bypass
REGISTER LENGTH
DESCRIPTION
1
Standard JTAG bypass register
Boundary Scan Register
Standard JTAG IDCODE Register
Boundary
1549
32
Device Identification
Boundary Scan Cell Types The C-5e NP boundary scan register contains only two cell types. All input cells are observe
only cells of type BC_4. All enable and output cells are standard cells of type BC_1. In IEEE
1149.1-1990 specification, the BC_4 cell is shown in Figure 7 and the BC_1 cell is shown in
Figure 8.
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
70
CHAPTER 2: SIGNAL DESCRIPTIONS
Figure 7 Observe-Only Cell
To next cell
From System Pin
To System Logic
G1
0
1
1D
C1
Figure 8 Cell Design That Can Be Used for Both Input and Output Pins
Node
To next cell
G1
Shift DR
To/From
System Pin
0
1
From/To
System
G1
0
1
1D
C1
1D
C1
From last cell
Clock DR
Update DR
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
JTAG Support
71
IDcode Register The C-5e NP implements a standard 32bit JTAG identification register. Table 34 lists the
value of the code for full identification and its subcomponents.
Table 34 JTAG Identification Code and Its Subcomponents
FIELD NAME
Version
WIDTH
BIT POSITIONS
BINARY VALUE
4
31-28
27-12
11-1
0
0000
Part Number
Manufacturer Identity
LSB
16
11
1
0000_0000_0010_0010
001_1001_0110
1
The concatenated 32bit value is hexidecimal 0002232d.
JTAG Instruction Register The C-5e NP contains a 4bit instruction register. Table 35 lists the instructions that are
supported.
Table 35 Instruction Register Instructions
INSTRUCTION MNEMONIC SELECTED REGISTER
INSTRUCTION OPCODE
Extest
Boundary Scan
0000
Idcode
Identification Register 0001
Sample/Preload
Highz
Boundary Scan
Bypass Register
Bypass Register
Bypass Register
Bypass Register
Bypass Register
Bypass Register
Bypass Register
Bypass Register
Bypass Register
Bypass Register
Bypass Register
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
Clamp
Bypass
Reserved*
Reserved*
Bypass
Bypass
Bypass
Bypass
Bypass
Bypass
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
72
CHAPTER 2: SIGNAL DESCRIPTIONS
Table 35 Instruction Register Instructions (continued)
INSTRUCTION MNEMONIC SELECTED REGISTER
INSTRUCTION OPCODE
Bypass
Bypass
Bypass Register
Bypass Register
1110
1111
*
There are two reserved instructions intended for Motorola Corporation’s internal
use. These should not be programmed by users.
Boundary Scan In order to simplify board test, Motorola Corporation has provided a boundary scan
Description Language
description language (BSDL) file (c5e.bsdl) in the Motorola web site that describes the
complete set of instructions, boundary scan order, and identification code value in an
industry standard format.
http://www.motorola.com/networkprocessors
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Chapter 3
ELECTRICAL SPECIFICATIONS
Absolute Maximum
Ratings
Table 36 lists the absolute maximum ratings for the C-5e network processor. Stresses
beyond those listed may cause permanent damage to the device. These are stress ratings
only and do not imply that operation under any conditions other than those listed under
“Recommended Operating Conditions” (Table 37) is possible.
Exposure to conditions beyond Table 36 can:
• Reduce device reliability
• Result in premature device failure, even with no immediate sign of failure
Prolonged exposure to conditions at or near the absolute maximum ratings could also
result in reduced useful life and reliability of the C-5e NP.
Table 36 C-5e Network Processor Absolute Maximum Ratings
PARAMETER
MIN
MAX
UNIT
V
VDD33/VDDT/VDDF Supply Voltage (3.3V input)* -0.5
+5
VDD Supply Voltage (1.25V input)*
Voltage on any pin
-0.5
+2.2
V
-0.5
VDD33 + 0.5†
V
Static Discharge Voltage
2000/200‡
-40
V
Storage Temperature
+125
+125
°C
°C
Absolute Maximum Junction Temperature
-40
*
Voltages are relative to Ground
5.5V allowed on PCI pins (pin name beginning with letter “P”)
HBM/MM
†
‡
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
74
CHAPTER 3: ELECTRICAL SPECIFICATIONS
Recommended Operating
Conditions
The recommended operating conditions describe an environment the C-5e NP network
processor is expected to encounter during normal operation. Table 37 delineates the
recommended operating parameters for the C-5e NP.
Table 37 C-5e Network Processor Recommended Operating Conditions
PARAMETER
MIN
NOMINAL MAX
UNIT
VDD33 Supply Voltage
VDDTSupply Voltage
VDDFSupply Voltage
3.135
3.135
3.3
3.3
3.465
3.465
V
V
V
2.375
3.135
2.5
3.3
2.625*
3.465
VDD Supply Voltage
1.19
1.25
1.31
0.7
V
IDD33 (VDD33 Supply Current)
IDDT (VDDT Supply Current)
IDDF (VDDF Supply Current)
IDD (VDD Supply Current)
Tj Junction Temperature
A
A
A
A
°C
0.5
0.1†
8.5
-40
125
*
For FP operation with I/Os @ 2.5V nominal.
For FP operation with I/Os @ 3.3V nominal.
†
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
DC Characteristics
75
DC Characteristics
The DC electrical characteristics define the input operating conditions for proper
operation and the output responses to applied DC signals and switch characteristics over
specified voltage and temperature ranges. The DC electrical characteristics are specified
within the recommended operating conditions including operating temperature and power
supply range as stated in this data sheet. Table 38 outlines the C-5e NP DC characteristics.
Table 38 C-5e Network Processor DC Characteristics
PARAMETER*
MIN
2.0
MAX
UNIT NOTES
LVTTL Input High Voltage
VDD33+.3
5.5
V
LVTTL Input High Voltage
(PCI pins)
2.0
V
PCI pins begin with letter “P”
in pin name.
LVTTL Input Low Voltage
-0.3
0.8
V
LVTTL Output High Voltage 2.4
LVTTL Output Low Voltage
V
@IOH = -2mA
0.4
+150
V
@IOL = +2mA
VIN = 0V or VDD33 †
LVTTL Input Current
-150
µA
V
LVPECL Input High Voltage
LVPECL Input Low Voltage
VDD33 -1.165 VDD33+.3V
-0.3
VDD33 -1.475
V
LVPECL Output High Voltage VDD33 -1.025 VDD33 -0.60
V
Load = 50ohm to VDD33 - 2V
Load = 50ohm to VDD33 - 2V
LVPECL Output Low Voltage VDD33 -2.20
VDD33 -1.620
+100
V
LVPECL Input Current
CPREF
-100
µA
V
VDD33 -1.38
VDD33 -1.26
Single-ended LVPECL
reference
*
All voltages are relative to Ground unless otherwise indicated.
Reflects current due to pullup/pulldown internal resistors.
†
Each control input pin has a capacitance associated with it. The capacitance at the control
input is due to the package and the input circuitry connected to the pin. Capacitance is
based on these conditions: TA = 25°C; VDD33 = 3.3V; f = 1MHz. Table 39 provides
capacitance data.
Table 39 C-5e Network Processor Capacitance Data
PARAMETER TYPICAL
All Pins
UNIT
5
pF
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
76
CHAPTER 3: ELECTRICAL SPECIFICATIONS
Power Sequencing
It is intended that the VDD33/VDDT/VDDF and VDD rails are sequenced to their final value
together. VDD33, VDDT and VDDF must be above VDD at all times to prevent internal
parasitic diodes from turning on and possibly damaging the device. VDD must be brought
to its final value within 100ms of sequencing on VDD33, VDDT and VDDF. During this
100ms, significant current may be drawn by the three IO supplies (up to 30A total) until
VDD is asserted to reset the IO drivers. To minimize this current draw during power-on, it
is recommended that this sequencing time be minimized in the power supply design.
It is also required that SCLK, SCLKX, TCLKI, PCLK, MDCLK, FTXCLK, and FRXCLK be running
or begin running during power sequencing to propagate reset inside the C-5e NP. Figure 9
indicates the relationship between the clocks and PRSTX. There is no requirement that the
asserting and deasserting edges of PRSTX be synchronous to the clocks. Reset must be
asserted within 100µs of power initiation. Typically, reset is held low during power
initiation.
Figure 9 Bringup Clock Timing Diagram
VDD, VDD33,
VDDT, VDDF
≤100µs
PRSTX
)
(
≥1ms
≥100µs
TCLKI, PCLK,
SCLK, SCLKX,
MDCLK, FTXCLK,
FRXCLK
) (
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Power and Thermal Characteristics
77
Power and Thermal
Characteristics
Table 40 provides the derived power and thermal characteristics for the production
version of the C-5e NP.
Table 40 C-5e Network Processor Power and Thermal Characteristics
PARAMETER
MIN
TYP
MAX
13.0
125
UNITS TEST CONDITIONS
Power Dissipation, PD
5.5
9.2
W
266MHz core clock*
Maximum Junction
Temperature, TJ
oC
Thermal Resistance, junction
<0.1
4.8
oC/W
oC/W
to case, θJC
Thermal Resistance, junction
to printed circuit board, θJB
*
Power dissipation values assume the following conditions: BMU memory operating at 133MHz. TLU memory
operating at 133MHz. QMU memory operating at 160MHz (refer to Table 57 for details. VDD= 1.25V, VDD33=
3.3V, TJ at approximately 50°C for typical values. VDD and VDD33 are 5% higher for maximum values.
“Minimum” PD based on idle conditions (clocks running and no programs executing). “Typical” PD based on
test application that implements Fast Ethernet forwarding actively running on all CPs. “Maximum” PD based
on maximum consumption for any high-bandwidth communications application executing on all CPs, FP
and XP.
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
78
CHAPTER 3: ELECTRICAL SPECIFICATIONS
Thermal Management This section provides thermal management information for the ceramic ball grid array
Information
(CBGA) package for air-cooled applications. Proper thermal control design is primarily
dependent on the system-level design—the heat sink, airflow, and thermal interface
material. To reduce the die-junction temperature, heat sinks may be attached to the
package by several methods—spring clip to holes in the printed-circuit board or package,
and mounting clip and screw assembly (refer to Figure 10); however, due to the potential
large mass of the heat sink, attachment through the printed circuit board is suggested. If a
spring clip is used, the spring force should not exceed 5.5 pounds.
Figure 10 Package Cross Section View with Several Heat Sink Options
Heat Sink
Heat Sink Clip
Thermal Interface Material
CBGA Package
Printed Circuit Board
Internal Package Conduction Resistance
For the exposed-die packaging technology the intrinsic conduction thermal resistance
paths are as follows:
• The die junction-to-case (or top-of-die for exposed silicon) thermal resistance
• The die junction-to-ball thermal resistance
Figure 11 depicts the primary heat transfer path for a package with an attached heat sink
mounted to a printed-circuit board.
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Power and Thermal Characteristics
79
Figure 11 Package with Heat Sink Mounted to the Printed Circuit Board
Radiation
External Resistance
Convection
Heat Sink
Thermal Interface Material
Die/Package
Die Junction
Package/Leads
Internal Resistance
Printed Circuit Board (PCB)
Radiation
Convection
External Resistance
Heat generated on the active side of the chip is conducted through the silicon, then
through the heat sink attach material (or thermal interface material), and finally to the
heat sink where it is removed by convection.
Because the silicon thermal resistance is quite small, for a first-order analysis, the
temperature drop in the silicon may be neglected. Thus, the thermal interface material
and the heat sink conduction/convective thermal resistances are the dominant terms.
Heat Sink Selection Example
For preliminary heat sink sizing, the die-junction temperature can be expressed as follows:
T j = T a + T r + (θjc + θint + θsa) x P d
where:
T j is the die-junction temperature
T a is the inlet cabinet ambient temperature
T r is the air temperature rise within the computer cabinet
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
80
CHAPTER 3: ELECTRICAL SPECIFICATIONS
θjc is the junction-to-case thermal resistance
θ
θ
P
int is the adhesive or interface material thermal resistance
sa is the heat sink base-to-ambient thermal resistance
d is the power dissipated by the device
During operation, the die-junction temperatures (T j) should be maintained less than the
value specified in Table 40. The temperature of the air cooling the component greatly
depends upon the ambient inlet air temperature and the air temperature rise within the
electronic cabinet. An electronic cabinet inlet-air temperature (T a) may range from 30° to
40°C. The air temperature rise within a cabinet (T r) may be in the range of 5° to 10°C. The
thermal resistance of the thermal interface material (θint) is typically about 1.5°C/W. For
example, assuming a T a of 30°C, a T r of 5°C, a CBGA package θjc = 0.1, and a maximum
power consumption (P d) of 13.0 W, the following expression for T j is obtained:
Die-junction temperature: T j = 30°C + 5°C + (0.1°C/W + 1.5°C/W + θsa) x 13.0 W
For this example, a θsa value of 5.3°C/W or less is required to maintain the die junction
temperature below the maximum value of Table 40.
Though the die junction-to-ambient and the heat sink-to-ambient thermal resistances are
a common figure-of-merit used for comparing the thermal performance of various
microelectronic packaging technologies, one should exercise caution when only using
this metric in determining thermal management because no single parameter can
adequately describe three-dimensional heat flow. The final die-junction operating
temperature is not only a function of the component-level thermal resistance, but the
system-level design and its operating conditions. In addition to the component's power
consumption, a number of factors affect the final operating die-junction
temperature—airflow, board population (local heat flux of adjacent components), heat
sink efficiency, heat sink attach, heat sink placement, next-level interconnect technology,
system air temperature rise, altitude, etc.
Due to the complexity and the many variations of system-level boundary conditions for
today's microelectronic equipment, the combined effects of the heat transfer
mechanisms (radiation, convection, and conduction) may vary widely. For these reasons,
we recommend using conjugate heat transfer models for the board, as well as
system-level designs.
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
AC Timing Specifications
81
AC Timing Specifications
AC timing specifications consist of input requirements and output responses. The input
requirements include setup and hold times, pulse widths, and high and low times. The
output responses include delays from clock to signal. The AC timing specifications are
defined separately for each interface to the C-5e NP.
See Figure 12. Output timing specifications for LVTTL pins are given with a 20pF load on
the output. Other loads can be simulated with the IBIS model available from Motorola.
The LVPECL driver is specified into a 50Ω load terminated to a (VDD33 - 2V) reference.
Figure 12 Test Loading Conditions
LVTTL
DUT
20pF
VDD33
+2V
LVPECL
DUT
50Ω
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
82
CHAPTER 3: ELECTRICAL SPECIFICATIONS
Clock Timing The system clock timing is shown in Figure 13 and described in Table 41.
Specifications
Figure 13 System Clock Timing Diagram
Cycle 2
Cycle 3
Cycle 4
Cycle 5
Cycle 1
SCLK
SCLKX
T
sc
T
sh
T
sl
CCLKn
T
ccN
T
cch
T
ccl
Table 41 System Clock Timing Description
SYMBOL PARAMETER MIN TYP
System Cycle Time 3.76
Sys Clk High Pulse 45
MAX UNIT COMMENT
Tsc
ns
266MHz core clock
Duty cycle*
Duty cycle*
T1†
Tsh
55
55
Tsl
Sys Clk Low Pulse 45
CCLK0 Cycle Time
Tcc0
Tcc1
Tcc2
Tcc3
Tcc4
Tcc5
Tcc6
Tcc7
Tcch
Tccl
647.67
488.28
29.097
22.353
20.00
9.412
8.00
ns
ns
ns
ns
ns
ns
ns
ns
CCLK1 Cycle Time
E1†
CCLK2 Cycle Time
E3†
CCLK3 Cycle Time
T3†
CCLK4 Cycle Time
RMII†
CCLK5 Cycle Time
Fibre Channel†
GMII†
CCLK6 Cycle Time
CCLK7 Cycle Time
6.43
OC-3†
CCLKm High Time 40%
CCLKm Low Time 40%
60%
60%
% cycle pulse is high
% cycle pulse is low
*
Pulse duty cycle measured at crossing voltage of SCLK/SCLKX
The frequencies specified for CCLK0 - CCLK7 allow full flexibility for the C-5e NP. It is also possible to use one
†
or more CCLKn inputs for other frequencies; contact your Motorola representative for more information.
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
AC Timing Specifications
83
CP Timing Specifications This section describes the timing for the following CP interfaces:
• DS1/DS3
• 10/100 Ethernet
• Gigabit Ethernet
• OC-3
• OC-12
DS1/DS3 Timing Specifications
The DS1/DS3 interface timing is shown in Figure 14 and described in Table 42.
Figure 14 DS1/DS3 Ethernet Timing Diagram
Cycle 2
Cycle 3
Cycle 4
Cycle 5
Cycle 1
CPn_0 (TCLK)
CPn_2/3 (Tx)
T
cdt
T
cdo
Cycle 5
Cycle 2
Cycle 3
Cycle 4
CPn_1 (RCLK)
CPn_4/5 (Rx)
T
cdr
T
T
cds
cdh
Table 42 DS1/DS3 Ethernet Timing Description
SYMBOL PARAMETER MIN
TYP
MAX
UNIT
ns
Tcdt
Tcdo
Tcdr
DS1/DS3 Transmit Cycle Time
647/22.4
DS1/DS3 Output Time
3.0/3.0
400/15.0 ns
ns
DS1/DS3 Receive Cycle Time
647/22.4
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
84
CHAPTER 3: ELECTRICAL SPECIFICATIONS
Table 42 DS1/DS3 Ethernet Timing Description (continued)
SYMBOL PARAMETER
MIN
2.0
0
TYP
MAX
UNIT
ns
Tcds
Tcdh
DS1/DS3 Setup Time
DS1/DS3 Hold Time
ns
10/100 Ethernet Timing Specifications
The 10/100 Ethernet interface timing is shown in Figure 15 and described in Table 43.
Figure 15 10/100 Ethernet Timing Diagram
Cycle 2
Cycle 3
Cycle 4
Cycle 5
Cycle 1
CPn_0 (TCLK)
CPn_2/3/6 (Tx)
CPn_1/4/5 (Rx)
T
cet
T
ceo
T
T
ceh
ces
Table 43 10/100 Ethernet Timing Description
SYMBOL PARAMETER
MIN
TYP
MAX
UNIT
ns
Tcet
Tceo
Tces
Tceh
Transmit Cycle Time*
20
Output Time
Setup Time
Hold Time
3.0
2.0
0
15.0
ns
ns
ns
*
STD/Fast Ethernet
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
AC Timing Specifications
85
Gigabit GMII Ethernet, TBI and MII Interface Timing Specifications
The Gigabit GMII Ethernet interface timing is shown in Figure 16 and described in
Table 44. The TBI interface timing is shown in Figure 16 and described in Table 45.
Figure 16 Gigabit Ethernet and TBI Interface Timing Diagram
Cycle 2
Cycle 3
Cycle 4
Cycle 5
GMII / TBI Tx
Cycle 1
CPn_0 (TCLK)
T
cgt
CPn_2-6 (Tx)
CPn+1_2-6 (Tx)
T
cgo
Cycle 1
Cycle 2
Cycle 3
MII Tx
MII CPn_1 (TCLKI)
T
cmt
MII CPn_2-6 (Tx)
T
cmo
TBI Rx
Cycle 1
Cycle 2
Cycle 3
Cycle 4
Cycle 5
CPn+2_1 (RCLK)
CPn+3_1 (RCLKN)
T
ctr
T
ctd
CPn+2_2-6 (Rx)
CPn+3_2-6 (Rx)
T
cts
T
cth
Cycle 1
Cycle 2
Cycle 3
Cycle 4
Cycle 5
GMII/MII Rx
CPn+2_1 (RCLK)
T
cgr
CPn+2_2-6 (Rx)
CPn+3_1-6 (Rx)
T
T
cgh
cgs
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
86
CHAPTER 3: ELECTRICAL SPECIFICATIONS
Table 44 Gigabit GMII/MII Ethernet Interface Timing Description
SYMBOL
GIGABIT PARAMETER
MIN
TYP
MAX
UNIT
ns
COMMENT
Tcgt
Transmit Cycle Time, GMII
8.0
Tcgo
Tcgr
Output Time, GMII
Receive Cycle Time
Setup Time
3.0
6.0
ns
8.0
ns
Tcgs
Tcgh
Tcmt
Tcmo
2.0
0.0
ns
Hold Time
ns
Transmit Cycle Time, MII
Output Time, MII
40/400
ns
100BaseT/10BaseT
2
8
ns
Table 45 Gigabit TBI Interface Timing Description
SYMBOL
TBI
PARAMETER
MIN
TYP
MAX
TOL
UNIT
ns
Tctt
Tcto
Tctr
Tctd
Tcts
Tcth
Transmit Cycle Time
Output Time
8.0
3.0
6.0*
ns
Receive Cycle Time
Rclk/Rclkn Deviation
Setup Time
16.0
ns
1.0
ns
2.0
0.0
ns
Hold Time
ns
*
For Fibre Channel applications this value is 7.0ns for a transmit cycle time of 9.4ns.
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
AC Timing Specifications
87
OC-3 Timing Specifications
The OC-3 interface timing is shown in Figure 17 and described in Table 46.
Figure 17 OC-3 Timing Diagram
Cycle 2
Cycle 3
Cycle 4
Cycle 5
Cycle 1
CPn_2
CPn_3
T
c3t
T
c3i
Cycle 1
Cycle 2
Cycle 3
Cycle 4
Cycle 5
CPn_0
CPn_1
T
c3r
T
c3d
CPn_4
CPn_5
T
c3s
T
c3h
T
c3s
T
c3h
Table 46 OC-3 Timing Description
SYMBOL PARAMETER
MIN
TYP
MAX
UNIT
ns
Tc3t
OC-3 Transmit Cycle Time
OC-3 Pulse Width
6.43
Tc3i
2.0
ns
Tc3r
OC-3 Receive Cycle Time* 6.0
ns
Tc3d
Tc3s
OC-3 Clock Duty Cycle
OC-3 Setup Time
OC-3 Hold Time
40
60
%
2.0
0.0
ns
Tc3h
155.52MHz
ns
*
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
88
CHAPTER 3: ELECTRICAL SPECIFICATIONS
OC-12 Timing Specifications
The OC-12 interface timing is shown in Figure 18 and described in Table 47.
Figure 18 OC-12 Timing Diagram
Cycle 2
Cycle 3
Cycle 4
Cycle 5
Cycle 1
CPn_1 (TCLKI)
CPn_0 (TCLK)
T
c12i
T
c12d
T
c12t
CPn_2-6 (Tx)
CPn+1_2-5 (Tx)
T
c12o
Cycle 1
Cycle 2
Cycle 3
CPn+2_1 (RCLK)
T
c12r
CPn+2_2-6 (Rx)
CPn+3_2-5 (Rx)
T
c12s
T
c12h
Table 47 OC-12 Timing Description
SYMBOL PARAMETER
MIN
TYP
MAX
60
UNIT
ns
Tc12i
Tc12d
Tc12t
Tc12o
Tc12r
Tc12s
Tc12h
OC-12 Transmit Cycle Time*
OC-12 Clock Duty Cycle
OC-12 Transmit Cycle Time†
OC-12 Output Time‡
12.86
40
%
12.86
12.86
ns
-0.1
12.0
2.0
2.2
ns
OC-12 Receive Cycle Time
OC-12 Setup Time
ns
ns
OC-12 Hold Time
0.0
ns
*
Input from PHY
Output from C-5e NP
Aligned to TCLK, negative edge
†
‡
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
AC Timing Specifications
89
Executive Processor The XP timing specifications include:
Timing Specifications
• PCI Timing Specifications
• MDIO Serial Interface Timing Specifications
• Low Speed Serial Interface Timing Specifications
• PROM Interface Timing Specifications
PCI Timing Specifications
The PCI timing is shown in Figure 19 and described in Table 48.
Figure 19 PCI Timing Diagram
Cycle 2
Cycle 3
Cycle 4
Cycle 5
Cycle 1
PCLK
T
pc
PAD/P_ctl
(output)
T
pao
T
paz
T
pav
PAD/P_ctl
(input)
T
T
T
pas
pah
PGNTX
(input)
T
pgs
pgh
PIDSEL
(input)
T
pis
T
pih
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
90
CHAPTER 3: ELECTRICAL SPECIFICATIONS
Table 48 PCI Timing Description
SYMBOL PARAMETER
MIN
15.0
3.0
0.0
2.0
2.0
2.0
5.1
0.0
3.0
0.0
TYP
MAX
UNIT
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Tpc
PCI Cycle Time*
PAD/P_ctl† Setup
PAD/P_ctl Hold
PAD/P_ctl Output
PAD/P_ctl Clk to Tri‡
PAD/P_ctl Clk to Driven‡
PGNTX Setup
Tpas
Tpah
Tpao
Tpaz
Tpav
Tpgs
Tpgh
Tpis
6.0
6.0
6.0
PGNTX Hold
PIDSEL Setup
Tpih
PIDSEL Hold
PRSTX**
PINTA**
*
66MHz PCI
†
P_ctl includes all PCI control parameters including: PPAR, PFRAMEX, PTRDYX, PIRDYX,
PSTOPX, PDEVSELX, PPERRX, PSERRX
Not fully tested, values based on design/characterization.
** Asynchronous
‡
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
AC Timing Specifications
91
MDIO Serial Interface Timing Specifications
The MDIO serial interface timing is shown in Figure 20 and described in Table 49.
Figure 20 MDIO Serial Interface Timing Diagram
Cycle 2
Cycle 3
Cycle 4
SICL
T
sic
SIDA
(output)
T
sods
T
sodh
SIDA
(input)
T
sids
Table 49 MDIO Serial Interface Timing Description
SYMBOL PARAMETER
MIN
40
TYP
MAX
UNIT
ns
Tsic
SICL Cycle Time
SIDA Input Setup
SIDA Input Hold
Tsids
Tsidh
Tsods
Tsodh
10
ns
0.0
ns
SIDA Output Setup 10
SIDA Output Hold 10
ns
ns
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
92
CHAPTER 3: ELECTRICAL SPECIFICATIONS
Low Speed Serial Interface Timing Specifications
The low speed serial interface timing is shown in Figure 21 and described in Table 50.
Figure 21 Low Speed Serial Interface Timing Diagram
Cycle 2
Cycle 3
SICL
T
slc
T
T
T
T
T
slb
slss
slhs
slhd
slsd
T
slst
SIDA
Table 50 Low Speed Serial Interface Timing Description
SYMBOL PARAMETER
MIN
2500
600
600
250
0.0
MAX
UNIT
ns
Tslc
SICL Cycle Time
Tslss
Tslhs
Tslsd
Tslhd
Tslst
Tslb
Set-up Time for Repeated START Condition
Hold Time START Condition
Data Set-up Time
ns
ns
ns
Data Hold Time
ns
Set-up Time for STOP Condition
Bus Free Time Between a STOP and START Condition
Capacitive load for each line of the bus
600
1250
ns
ns
Cmax
400
pF
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
AC Timing Specifications
93
PROM Interface Timing Specifications
The PROM interface timing is shown in Figure 22 and described in Table 51.
Figure 22 PROM Interface Timing Diagram
Cycle 2
Cycle 3
Cycle 4
Cycle 5
Cycle 1
SPCK
SPDI
T
spc
T
T
spih
spis
SPLD
SPDO
T
splo
T
spdo
Table 51 PROM Interface Timing Description
SYMBOL PARAMETER MIN TYP
SPCK Cycle Time 40.0
MAX
UNIT
ns
Tspc
Tspis
Tspih
Tsplo
Tspdo
SPDI Setup
SPDI Hold
10.0
0.0
ns
ns
SPLD Output
SPDO Output
Tsc
Tsc
Tsc + 3.0
Tsc + 3.0
ns
ns
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
94
CHAPTER 3: ELECTRICAL SPECIFICATIONS
Fabric Processor Timing The FP timing specifications are shown in Figure 23 and described in Table 52.
Specifications
Figure 23 Fabric Processor Timing Diagram
Cycle 2
Cycle 3
Cycle 4
Cycle 5
Cycle 1
FRXCLK
T
frc
FRXCTL
(output)
T
frco
T
T
frcv
frcz
FRXCTL
(input)
T
T
T
T
frcs
frds
frch
FINn
frdh
FTXCLK
T
ftc
FTXCTL
(output)
T
ftco
T
T
ftcv
ftcz
FTXCTL
(input)
T
T
ftcs
ftch
FOUTn
T
ftdo
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
AC Timing Specifications
95
Table 52 Fabric Processor Timing Description
SYMBOL PARAMETER
MIN
TYP
MAX
UNIT
ns
COMMENT
Tfrc
FRX Cycle Time
FRXCTL Setup
8.0
Tfrcs
4.0
1.5
ns
Utopia2 Mode
All other modes
Tfrch
Tfrco
Tfrcz
Tfrcv
Tfrds
FRXCTL Hold
0.0
1.0
1.0
1.0
ns
ns
ns
ns
ns
FRXCTL Output
FRXCTL Clk to Tri*
FRXCTL Clk to Driven*
FIN Setup
4.0
4.0
4.0
4.0
1.5
Utopia2 Mode
All other modes
Tfrdh
Tftc
FIN Hold
0.0
8.0
ns
ns
ns
FTX Cycle Time
FTXCTL Setup
Tftcs
4.0
1.5
Utopia2 Mode
All other modes
Tftch
Tftco
Tftcz
Tftcv
Tftdo
FTXCTL Hold
0.0
1.0
1.0
1.0
1.0
ns
ns
ns
ns
ns
FTXCTL Output
FTXCTL Clk to Tri*
FTXCTL Tri to Driven*
FOUT Output
4.0
4.0
4.0
4.0
*
Not fully tested, values based on design/characterization.
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
96
CHAPTER 3: ELECTRICAL SPECIFICATIONS
BMU Timing The BMU timing specifications are shown in Figure 24 and described in Table 53.
Specifications
The BMU synchronous DRAM interface is PC100-compliant and designed to work with
industry standard SDRAM components with 12 or fewer address lines. The information
below is intended to provide the output, setup, and hold data required to design this
interface without duplicating the transaction waveform diagrams in SDRAM data sheets.
Figure 24 BMU Timing Diagram
Cycle 2
Cycle 3
Cycle 4
Cycle 5
Cycle 1
MDCLK
M_ctl
T
mco
mao
mc
T
MAn
MDn
T
(output)
T
mdo
T
T
mdv
mdz
MDn
(input)
T
T
mdh
mds
Table 53 BMU Timing Description
SYMBOL PARAMETER
MIN
TYP
MAX
UNIT
ns
Tmc
BMU Cycle Time
7.5
0.8
0.8
0.5
1.1
0.8
0.8
0.8
Tmco
Tmao
Tmds
Tmdh
Tmdo
Tmdz
Tmdv
Tr, Tf
BMU Ctrl Output
BMU Addr Output
BMU Data Setup
BMU Data Hold
3.5
3.7
ns
ns
ns
ns
BMU Data Output
BMU Data Clk to Tri*
BMU Data Clk to Driven*
MDCLK Rise, Fall
4.4
ns
4.4
ns
4.4
ns
2.0 †
ns
*
Not fully tested, values based on design/characterization.
Measured 0.8V to 2.0V.
†
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
AC Timing Specifications
97
Table 54 Signal Groups in BMU Timing Diagrams
SIGNAL GROUP
Control (M_ctl)
Address (MAn)
Data (MDn)
INCLUDED SIGNALS
MBA0, MBA1, MCASX, MRASX, MWEX, MCSX, MDQM, MDQML
MA0 - MA11
MD0 - MD129, MDECC0 - MDECC8
TLU Timing Specifications The TLU timing specifications are shown in Figure 25 and described in Table 55.
Figure 25 TLU Timing Diagram
Cycle 2
Cycle 3
Cycle 4
Cycle 5
Cycle 1
TCLKI
T_ctl
T
tc
T
tco
TAn
T
tao
TDn
(output)
T
T
tdo
tdv
T
tdz
TDn
(input)
T
T
tdh
tds
Table 55 TLU Timing Description
SYMBOL PARAMETER
MIN
7.5
0.8
0.8
1.0
1.2
0.8
TYP
MAX
UNIT
Ttc
TLU Cycle Time
TLU Ctrl Output
TLU Addr Output
TLU Data Setup
TLU Data Hold
TLU Data Output
ns
ns
ns
ns
ns
ns
Ttco
Ttao
Ttds
Ttdh
Ttdo
4.0
3.9
4.5
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
98
CHAPTER 3: ELECTRICAL SPECIFICATIONS
Table 55 TLU Timing Description (continued) (continued)
SYMBOL PARAMETER
MIN
0.8
TYP
MAX
4.5
UNIT
ns
Ttdz
Ttdv
Tr, Tf
TLU Data Clk to Tri*
TLU Data Clk to Driven*
TCLKI Rise, Fall
0.8
4.5
ns
2.0 †
ns
*
Not fully tested, values based on design/characterization.
Measured 0.8V to 2.0V.
†
Table 56 Signal Groups in TLU Timing Diagrams
SIGNAL GROUP
Control (T_ctl)
Address (TAn)
Data (TDn)
INCLUDED SIGNALS
TCE0X - TCE3X, TWE0X - TWE3X
TA0 - TA21
TD0 - TD63, TPAR0-3
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
AC Timing Specifications
99
QMU SRAM (Internal The QMU SRAM (Internal Mode) timing specifications are shown in Figure 26 and
Mode) Timing
Specifications
described in Table 57.
Figure 26 QMU SRAM (Internal Mode) Timing Diagram
Cycle 2
Cycle 3
Cycle 4
Cycle 5
Cycle 1
QACLKI
Q_ctl
T
qc
T
qco
QAn
T
qao
QDn
(output)
T
T
qdv
qdo
T
qdz
QDn
(input)
T
qdh
T
qds
Table 57 QMU SRAM (Internal Mode) Timing Description
SYMBOL PARAMETER MIN TYP MAX UNIT COMMENT
Tqc
QMU Cycle Time
6.25
6.67
ns
With QMU on-board memory
With QMU memory daughter board
Tqco
Tqao
Tqds
Tqdh
Tqdo
Tqdz
QMU Ctrl Output
0.8
3.9
3.7
ns
ns
ns
ns
ns
ns
Loading is 50Ω transmission line.
Loading is 50Ω transmission line.
QMU Addr Output 0.8
QMU Data Setup
QMU Data Hold
QMU Data Output
0.8
0.8
0.9
4.0
4.0
Loading is 50Ω transmission line.
QMU Data Clk to Tri* 0.9
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
100
CHAPTER 3: ELECTRICAL SPECIFICATIONS
Table 57 QMU SRAM (Internal Mode) Timing Description (continued)
SYMBOL PARAMETER MIN TYP MAX UNIT COMMENT
0.9 4.0 ns
Tqdv
QMU Data Clk to
Driven*
Tr, Tf
QACLKI Rise, Fall
2.0 † ns
*
Not fully tested, values based on design/characterization.
Measured 0.8V to 2.0V.
†
Table 58 Signal Groups in QMU SRAM (Internal Mode) Timing Diagrams
SIGNAL GROUP
Control (Q_ctl)
Address (QAn)
Data (QDn)
INCLUDED SIGNALS
QWEX
QA0-QA16
QD0-QD31, QDPL, QDPH
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
AC Timing Specifications
101
QMU to Q-5 TMC (External The QMU to Q-5 TMC (External Mode) timing specifications are shown in Figure 27 and
Mode) Timing
Specifications
described in Table 59.
Figure 27 QMU to Q-5 TMC (External Mode) Timing Diagram
Cycle 2
Cycle 1
T
qec
QACLKI
QBCLKI
T
T
qep
qep
T
qec
DQDATA
T
T
qeh
qeh
T
T
T
qes
qes
qec
QACLKO
QBCLKO
T
T
qep
qep
T
qec
NQDATA
T
T
qeomax
qeomax
T
T
qeomin
qeomin
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
102
CHAPTER 3: ELECTRICAL SPECIFICATIONS
Table 59 QMU to Q-5 TMC (External Mode) Timing Description
SYMBOL PARAMETER
MIN TYP
MAX
UNIT COMMENT
Tqec
Tqep
QMU External Cycle Time
10.0
ns
QACLKO/QBCLKO
derived from
QACLKI/QBCLKI
QMU CLKA-CLKB delta
between rising edges
4.8
ns
Tqes
Tqeh
Tqeo
QMU Input Data Setup
QMU Input Data Hold
QMU Data Output
0.6
0.8
-.85
ns
ns
ns
1.3
Determines valid time
for data from each clock
rising edge
Tr, Tf
QACLKI, QBCLKI Rise, Fall
2.0 * ns
*
Measured 0.8V to 2.0V.
Table 60 Signal Groups in QMU to Q-5 TMC (External Mode) Timing Diagrams
SIGNAL GROUP
INCLUDED SIGNALS
Input Clocks (QnCLKI)
Output Clocks (QnCLKO)
Input Data (DQDATA)
Output Data (NQDATA)
QACLKI, QBCLKI
QACLKO, QBCLKO
QD0-23, QARDY, QDPL, QDPH, QNQRDY, QDQPAR
QA0-16, QWEX, QD24-31
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Chapter 4
MECHANICAL SPECIFICATIONS
Package Views
The C-5e network processor is an 840 pin (29 pins x 29 pins) Ball Grid Array (BGA) package
as shown in the following illustrations. Table 61 defines the package measurements.
Figure 28 C-5e Network Processor BGA Package (Side View)
A2
A4
A3
A
A1
Seating Plane
HiTCE: Green ceramic is thermally matched to FR4 circuit board.
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
104
CHAPTER 4: MECHANICAL SPECIFICATIONS
Figure 29 C-5e Network Processor BGA Package (Bottom View)
D
D1
e
AJ
AH
AG
AF
AE
AD
AC
AB
AA
Y
e
W
V
U
T
E1
E
R
P
N
M
L
K
J
H
b
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Package Measurements
105
Package Measurements
Table 61 defines the C-5e NP package measurements, providing nominal, minimum, and
maximum sizes where appropriate.
Table 61 Package Measurements (Reference Figure 28, and Figure 29 for Symbols)
SYMBOL DEFINITION
NOM. (MM) MIN. (MM) MAX. (MM)
A
Overall
3.26
0.70
0.86
2.97
0.6
3.55
0.8
A1
A2
A3
A4
D
Ball height
Die height
0.82
1.55
0.9
Body thickness 1.7
Capacitorheight
1.85
0.6
Body size
31.00
30.80
30.80
31.20
D1
E
Ball footprint (X) 28.00
Body size
31.00
31.20
E1
e
Ball footprint (Y) 28.00
Ball pitch
1.00
0.70
b
Ball diameter
Keep Out Zones Figure 30 shows the C-5e NP keep out zones and Table 62 defines their measurements,
providing minimum and maximum sizes where appropriate.
Since 14 capacitors are present on all devices, caution must be taken not to short
capacitors or exposed metal capacitor pads on package top. This can be achieved by
noting the capacitors zones as detailed here.
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
106
CHAPTER 4: MECHANICAL SPECIFICATIONS
Figure 30 C-5e Network Processor BGA Package (Top View)
D5
D3
Probe Pad
Die
D2
Capacitor
Pads
E3
E2
E4
18ARS10517D001
D4
Table 62 Keep Out Zone’s Measurements (Reference Figure 30 for Symbols)
SYMBOL DEFINITION
NOM. (MM) MIN. (MM) MAX. (MM)
D2
D3
D4
D5
E2
Keep out zones
0.675
2.925
6.95
9.25
9.5
E3
11.8
7.875
E4
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Marking Codes
107
Marking Codes
Table 63 explains the marking on the C-5e NP.
Table 63 C-5e Network Processor Marking Codes
MARKING (EXPLANATION OF CODES)
Top
Logo/Part#/Date Code
N/A
Bottom
Pin 1 Marking Chamfered Corner
Reflow
Typical Reflow Profile for the C-5e Switch Module comprises:
1
Follow the guidelines recommended by your solder paste supplier.
Flux requirements must be met for best solderability.
2
The temperature profile should be carefully characterized to ensure uniform
temperature across the board and package.
Solder ball voiding may be affected by ramp rates and dwell times below and above
liquids.
3
A nitrogen atmosphere is not required, but will make the process more robust. It can
make a difference for marginally solderable PC board pads.
4
Full convection forced air furnaces work best, but IR, Convection/IR, or vapor phase can
be used.
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
108
CHAPTER 4: MECHANICAL SPECIFICATIONS
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
INDEX
Channel Processors 22
Channel Processors Physical Interface Signals and Pins
Grouped by Clusters 33
Clock and Reference Signals 31
Clock Signals 31
Clock Timing Specifications 82
Configuration
Symbols
10/100 Ethernet (RMII) Configuration 34
10/100 Ethernet Signals 34
10/100 Ethernet Timing Description 84
10/100 Ethernet Timing Diagram 84
10/100 Ethernet Timing Specifications 84
10/100 Ethernet (RMII) 34
DS1/T1 Framer Interface 34
FibreChannel TBI 38
A
Gigabit Ethernet 38
Absolute Maximum Ratings 73
AC Timing Specifications 81
Gigabit Ethernet (GMII) 35
SONET OC-12 Transceiver Interface 40
SONET OC-3 Transceiver Interface 39
Configurations
GMII/TBI Transmit and Receive Pin 36
CP Timing Specifications 83
B
Block Diagram, C-5e Network Processor 20
BMU SDRAM Interface Signals 52
BMU Signal Groups 97
CSIX-L1 Mode, C-5e Network Processor to Fabric Interface Pin
Mapping 51
BMU Timing Description 96
BMU Timing Diagram 96
BMU Timing Specifications 96
Boundary Scan Cell Types 69
Boundary Scan Description Language 72
Bringup Clock Timing Diagram 76
Buffer Management Unit 24
D
Data Registers
JTAG 69
DC Characteristics 75
Description
Functional 19
Description Language
Boundary Scan 72
Descriptions
Signal 27
Diagram
C
C-5e Network Processor Absolute Maximum Ratings 73
C-5e Network Processor BGA Package, Bottom View 104
C-5e Network Processor BGA Package, Side View 103
C-5e Network Processor Capacitance Data 75
C-5e Network Processor DC Characteristics 75
C-5e Network Processor Power and Thermal Characteristics 77
C-5e NP Channel Processors 22
10/100 Ethernet Timing 84
BMU Timing 96
Bringup Clock Timing 76
DS1/DS3 Ethernet Timing 83
Channel Processor Interface Signals 32
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
110
INDEX
Fabric Processor Timing 94
Gigabit Ethernet (TBI) Timing 85
Low Speed Serial Interface Timing 92
MDIO Serial Interface Timing 91
OC-3 Timing 87
Fabric Processor Interface Signals 47
Fabric Processor Timing Description 95
Fabric Processor Timing Diagram 94
Fabric Processor Timing Specifications 94
Functional Description 19
PCI Timing 89
Pinout 28
PROM Interface 45
PROM Interface Timing 93
QMU Timing 99
G
General System Interface Signal 47
Gigabit Ethernet (GMII) Configuration 35
Gigabit Ethernet (GMII) Signals
Signal Groups in BMU Timing 97
Signal Groups in QMU Timing 100
Signal Groups in TLU Timing 98
System Clock Timing 82
TLU Timing 97
One Cluster Example 36
Gigabit Ethernet (TBI) Timing Description 86, 86
Gigabit Ethernet (TBI) Timing Diagram 85
Gigabit Ethernet and FibreChannel TBI Configuration 38
Gigabit Ethernet and FibreChannel TBI Signals
Example 38
Diagram, Block
C-5e Network Processor 20
DS1/DS3 Ethernet Timing Description 83
DS1/DS3 Ethernet Timing Diagram 83
DS1/DS3 Timing Specifications 83
Gigabit GMII Ethernet, TBI and MII Interface Timing Specification 85
GMII/TBI Transmit and Receive Pin Configurations 36
DS1/T1 Framer Interface Configuration 34
DS1/T1 Framer Interface Signals 34
I
IDcode Register 71
E
Instruction Register Instructions 71
Electrical Specifications 73
Absolute Maximum Ratings 73
Executive Processor 23
PCI 23
J
JTAG Data Registers 69
PROM Interface 24
JTAG Identification Code and Its Sub-components 71
JTAG Instruction Register 71
JTAG Internal Register Descriptions 69
JTAG Support
Serial Bus Interface 23
System Interface Signals 41
System Interfaces 23
Executive Processor Timing Specifications 89
Pinouts 69
F
L
Fabric Interface Pin Mapping
CSIX-L1 Mode 51
Low Speed Serial Interface Timing Description 92
Low Speed Serial Interface Timing Diagram 92
Low Speed Serial Interface Timing Specifications 92
LVPECL Specifications 30
Power X(CSIX-L0) Mode 50
PRIZMA Mode 50
Utopia2/Utopia3 ATM Mode 49
Utopia2/Utopia3 PHY Mode 49
Fabric Processor 24
LVTTL Specifications 30
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
INDEX
111
PROM Interface Diagram 45
PROM Interface Signals 44
M
PROM Interface Timing Description 93
PROM Interface Timing Diagram 93
PROM Interface Timing Outline 46
PROM Interface Timing Specifications 93
MDIO Serial Interface Timing Description 91
MDIO Serial Interface Timing Diagram 91
MDIO Serial Interface Timing Specifications 91
Measurements
C-5e Network Processor 105
Mechanical Specifications 103
Miscellaneous Test Signals for JTAG, Scan, and Internal Test
Routines 58
Q
QMU Signal Groups 100
QMU SRAM (Internal Mode) Interface Signals 55
QMU SRAM (Internal Mode) Timing Diagram 99
QMU Timing Description 99
QMU Timing Specifications 99
N
No Connection Pins 58
QMU to Q-5 TMC (External Mode) Interface Signals 56
QMU to Q-5 TMC (External Mode) Timing Diagram 101
Queue Management Unit 26
O
OC-12 Signals 40
OC-12 Timing Description 88
OC-12 Timing Specifications 88
OC-3 Signals 39
OC-3 Timing Description 87
OC-3 Timing Diagram 87
OC-3 Timing Specifications 87
Operating Conditions, Recommended 74
R
Recommended Operating Conditions 74
Register
IDcode 71
JTAG Instruction 71
S
Serial Interface Signals 43
Serial Port Signals 43
Signal
P
Package Measurements 105
PCI Signals 41
General System Interface 47
Signal Descriptions 27
Signal Summary 27
Signals
PCI Timing Description 90
PCI Timing Diagram 89
PCI Timing Specifications 89
Pin Descriptions
10/100 Ethernet 34
BMU SDRAM Interface 52
Channel Processor Interface 32
Clock 31
Grouped by Function 30
Pin Locations 28
Pin Number Signals Groups 59
Pinout Diagram 28
Clock and Reference 31
DS1/T1 Framer Interface 34
Fabric Processor Interface 47
Grouped by Pin Number 59
OC-12 40
Power Sequencing 76, 77
Power Supply Signals 57
Power X(CSIX-L0) Mode, Fabric Interface Pin Mapping 50
PRIZMA Mode, C-5e Network Processor to Fabric Interface Pin
Mapping 50
OC-3 39
Processor, Executive 23
PCI 41
Processor, Fabric 24
MOTOROLA GENERAL BUSINESS INFORMATION
C5ENPB0-DS REV 05
112
INDEX
Power Supply 57
System Interfaces
PROM Interface 44
Executive Processor 23
QMU SRAM (Internal Mode) Interface 55
QMU to Q-5 TMC (External Mode) Interface 56
Serial Interface 43
T
Serial Port 43
Table Lookup Unit 25
Test Signals 58
Test 58
TLU SRAM Interface 54
SONET OC-12 Transceiver Interface Configuration 40
SONET OC-3 Transceiver Interface Configuration 39
Specifications
Test Signals, Miscellaneous, For JTAG, Scan, and Internal Test
Routines 58
Timing Outline
PROM Interface 46
10/100 Ethernet Timing 84
AC Timing 81
BMU Timing 96
Clock Timing 82
CP Timing 83
TLU Signal Groups 98
TLU SRAM Interface Signals 54
TLU Timing Description 97
TLU Timing Diagram 97
TLU Timing Specifications 97
Transceiver Interface Configuration
SONET OC-12 40
DS1/DS3 Timing 83
Electrical 73
Executive Processor Timing 89
Fabric Processor Timing 94
Gigabit GMII Ethernet, TBI and MII Interface Timing
Specification 85
Low Speed Serial Interface Timing 92
MDIO Serial Interface Timing 91
Mechanical 103
OC-12 Timing 88
OC-3 Timing 87
PCI Timing 89
PROM Interface Timing 93
QMU Timing 99
SONET OC-3 39
Transmit and Receive Pin Combinations for Gigabit Ethernet and
FibreChannel 35
U
Utopia2/Utopia3 ATM Mode, C-5e Network Processor to Fabric
Interface Pin Mapping 49
Utopia2/Utopia3 PHY Mode, C-5e Network Processor to Fabric
Interface Pin Mapping 49
TLU Timing 97
XP Timing 89
System Clock Timing Description 82
System Clock Timing Diagram 82
X
XP Timing Specifications 89
C5ENPB0-DS REV 05
MOTOROLA GENERAL BUSINESS INFORMATION
Motorola, Inc. C-Port Family of Network Processors
120 Water Street, No. Andover, MA 01845 Voice: (978) 773-2300 FAX: (978) 773-2301
Search
Select Country
Advanced | Parametric | Part Number | FAQ
Motorola Home | Semiconductors Home | Contact Us
Products | Design Support | Register | Login
Semiconductors
Motorola > Semiconductors > Products > Network and Communication Processors > C-Port™ Network Processor Family > Network Processors > C-5E
C-5E : C-5e™ Network Processor (NP)
Page Contents:
The C-5e™ Network Processor (NP), the second generation of the C-Port™ family of network processors,
is the most integrated, flexible, and functionally-rich processor for developing and deploying advanced
services for next-generation networks.
Features
Parametrics
Documentation
Tools
Product Picture
Block Diagram
Applications
Orderable Parts
Related Links
C-5E Features
Other Info:
3rd Party Design Help
3rd Party Tool
Vendors
With its 5Gbps of bandwidth and more than 4500 MIPs of computing power, the C-5e NP more than
satisfies the demanding communications requirements for intelligent network services, such as
classification, traffic management, and interworking functions. A comprehensive Quality of Service (QoS)
management solution is enabled with the addition of the best-in-class C-Port Q-5™ Traffic Management
Coprocessor (TMC). The Q-5 TMC provides the queues, service classes, and scheduling regimes to
support a wide range of sophisticated QoS-enabled applications running on the C-5e NP. The C-Port M-
5™ Channel Adapter extends the C-5e NP's data bandwidth reach to support full-duplex OC-48c/STM-16
applications and enable high-speed network services.
3rd Party Trainers
Rate this Page
--
-
0
+
++
Submit
The C-5e NP also integrates standard programming interfaces, a complete development environment, and
third-party support from Motorola's Smart Networks Alliance to provide a platform approach that can
simplify and speed the development of full-featured networking applications today, enable faster develop-
ment within and across product families, and provide a smooth migration path to future product
generations.
Care to Comment?
C-Port Family Support Website
This secure website provides access to C-Port family supplemental information and software downloads
not available on the C-Port product pages.
Return to Top
C-5E Parametrics
Part Parametrics
Part Number
Package Description
FCCBGA 840 31SQ*3.55P1.0
MCC5E0RX266WB0B
C-5E Documentation
Documentation
Application Note
Date Last
Modified
Order
Availability
ID
Name
Vendor ID Format Size K Rev #
SECURITY-AN
Security Implementations for the C-5 NP
MOTOROLA
pdf
151
0
1/06/2002
-
Brochure
Size
K
Date Last
Modified
Order
Availability
ID
Name
Vendor ID Format
pdf
Rev #
CPORTFAMILY-BR
C-Port Network Processor Family Brochure MOTOROLA
157
2
3/20/2003
-
Data Sheets
Size Rev Date Last
Order
ID
Name
Vendor ID Format
K
#
Modified Availability
MOTOROLA
pdf
1669
11/08/2002
C5ENPA1-DS/D
C5ENPB0-DS
C-5e Network Processor Data Sheet Silicon Revision A1
C-5e Network Processor Data Sheet Silicon Revision B0
3
MOTOROLA
pdf
1710
5
8/11/2003
Fact Sheets
ID
Size Rev Date Last
Order
Name
Vendor ID Format
K
#
Modified Availability
MOTOROLA
pdf
227
C5ENP-PB/D
C-5e Network Processor Product Brief
5
3/20/2003
7/16/2002
3/20/2003
-
-
Smart Networks Alliance Solutions Brief for Corrent
Corporation
MOTOROLA
pdf
378
639
CORRENT-FS/D
CPORTBSC-FS/D
2
3
Application Fact Sheet: Access 2.5G/3G Wireless
Basestation Controller Network Interface
MOTOROLA
pdf
CPORTDSLAM-
FS/D
MOTOROLA
pdf
882
385
986
Application Fact Sheet: Access Multiservice DSLAM
Fact Sheet: C-Port Network Processor Family
2
4
2
3/20/2003
CPORTFAMILY-
FS/D
MOTOROLA
pdf
10/17/2002
-
CPORTMEDIA-
FS/D
Application Fact Sheet: Access Media Gateway with IP and MOTOROLA
ATM Internetworking
pdf
3/20/2003
3/20/2003
CPORTMSP-FS/D
Application Fact Sheet: Access/Edge Multiservice Platform MOTOROLA
ATM/IP/FR Line Card
394
376
201
pdf
pdf
pdf
3
1
1
Smart Networks Alliance Solutions Brief for HCL
Technologies
MOTOROLA
HCLT-FS/D
M2ADAPFS
7/16/2002
-
-
M-2 Utopia/POS-PHY Adapter Reference Design Fact
Sheet
MOTOROLA
11/13/2002
M5ADAPTER-
FS/D
MOTOROLA
Fact Sheet: M-5 Channel Adapter
pdf
pdf
pdf
58
1
1
3
3/20/2003
7/16/2002
7/16/2002
-
-
-
Smart Networks Alliance Solutions Brief for SiSilk Networks MOTOROLA
472
SISILK-FS/D
WINDRIVER-FS/D
Smart Networks Alliance Solutions Brief for Wind River
Systems
MOTOROLA
397
Product Change Notices
Date Last
Modified
Order
Availability
ID
Name
Vendor ID Format Size K Rev #
MOTOROLA htm
PCN9103
C-3E AND C-5E MC QUALIFICATION
3
0
8/20/2003
-
Reference Manual
ID
Size Rev Date Last
Order
Name
Vendor ID Format
K
#
Modified Availability
C5EC3EARCH-
RM/D
C-5e/C-3e Network Processor Architecture Guide Silicon MOTOROLA
Revision A0
9848
10/17/2002
-
pdf
2
Selector Guide
ID
Size Rev Date Last
Order
Name
Vendor ID Format
K
#
Modified Availability
Network and Communications Processors Selector Guide - MOTOROLA
Quarter 4, 2003
183
10/24/2003
SG1007
pdf
pdf
0
MOTOROLA
SG2000CR
Application Selector Guide Index and Cross-Reference.
92
0
2
0
6/16/2003
6/24/2002
Application Summary - Access - Cable Modem Termination
System (CMTS) provides connectivity, basic
MOTOROLA
SG2122
pdf
routing/switching of protocol data units (PDUs), protocol
conversion, traffic management, and other services.
Application Selector Guide - Access 2.5G / 3G WIRELESS MOTOROLA
BSC NETWORK INTERFACE
SG2123
SG2124
SG2126/D
pdf
pdf
pdf
0
1
1
1
6/17/2003
6/17/2003
6/17/2003
ApplicationSelector Guide - Edge MULTISERVICE
PLATFORM ATM/IP/FR LINE CARD
MOTOROLA
0
Application Selector Guide - Access MEDIA GATEWAY
WITH IP AND ATM INTERWORKING
MOTOROLA
152
White Paper
ID
Size Rev Date Last
Order
Name
Vendor ID Format
K
#
Modified Availability
Communications Processors: A Definition and Comparison MOTOROLA
229 2.01
COMMPROCWP
CPPM00WP100
pdf
pdf
5/21/2001
-
-
Network Processor Programming Models: The Key to
MOTOROLA
206
Achieving Faster Time-To-Market and Extending Product
1.0 5/21/2001
Life
MSPCPORT-
WP/D
Addressing Multiservice Access Platform Design Issues
with Network Processors
MOTOROLA
MOTOROLA
160
184
pdf
pdf
1
0
3/20/2003
-
10/22/2001
QOSM-WP
Quality of Service Management - What Does It Take?
Return to Top
C-5E Tools
Hardware Tools
Evaluation/Development Boards and Systems
Size Rev
Order
Availability
ID Name
Vendor ID Format
K
#
C-Ware™
Development
System
CDS
MOTOROLA
-
-
-
-
Software
Application Software
Reference Applications
ID
Name
Vendor ID
Format Size K Rev # Order Availability
CAL
C-Ware™ Applications Library
MOTOROLA
-
-
-
-
Protocol Stacks
ID
Name
Vendor ID Format Size K Rev # Order Availability
INFOLINK-STACKNAME
LINK
INFOLink Protocol Software Family
-
-
-
-
Software Tools
IDE (Integrated Development Environment)
ID
Name
Vendor ID
MOTOROLA
Format Size K Rev #
Order Availability
CST
C-Ware™ Software Toolset
-
-
-
-
Return to Top
Applications
Networking and Communications
Access
2.5G/3G Wireless BSC Network Interface
Cable Modem Termination System
Multiservice Digital Subscriber Line Access Multiplexer (DSLAM)
Media Gateway with IP and ATM Interworking
Multiservice Platform ATM/IP/FR Line Card
Return to Top
Orderable Parts Information
Order
Budgetary
Price
QTY 1000+
($US)
Tape
and
Reel
Life Cycle Description
(code)
PartNumber
Package Info
Additional Info
Availability
FCCBGA 840
31SQ*3.55P1.0
PRODUCT NEWLY
INTRO'D/RAMP-UP(1)
more
MCC5E0RX266WB0B
No
-
NOTE: Are you looking for an obsolete orderable part? Click HERE to check our distributors' inventory.
Return to Top
Related Links
C-Port™ Network Processors
Digital Signal Processors
Networking
PowerPC™ Processors
PowerQUICC™ Communication Processors
C-Port Family Support website
Return to Top
www.motorola.com | Site Map | Contact Motorola | Terms of Use | Privacy Practices
© Copyright 1994-2003 Motorola, Inc. All Rights Reserved.
相关型号:
MCC60-16IO1B
Silicon Controlled Rectifier, 100A I(T)RMS, 100000mA I(T), 1600V V(DRM), 1600V V(RRM), 2 Element, TO-240AA, TO-240AA, 7 PIN
LITTELFUSE
©2020 ICPDF网 联系我们和版权申明