MC10216LS [MOTOROLA]

Line Driver/Receiver, ECL10K, CDIP16;


型号：	MC10216LS
厂家：	MOTOROLA
描述：	Line Driver/Receiver, ECL10K, CDIP16 线路驱动器或接收器驱动程序和接口接口集成电路
文件：	总5页 (文件大小：108K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

SEMICONDUCTOR TECHNICAL DATA

The MC10216 is a high speed triple differential amplifier designed for use in

sensing differential signals over long lines. The base bias supply (V ) is made

available at pin 11 to make the device useful as a Schmitt trigger, or in other

applications where a stable reference voltage is necessary.

Active current sources provide the MC10216 with excellent common mode

noise rejection. If any amplifier in a package is not used, one input of that

L SUFFIX

CERAMIC PACKAGE

CASE 620–10

amplifier must be connected to V

source bias network.

(pin 11) to prevent upsetting the current

Complementary outputs are provided to allow driving twisted pair lines, to

enable cascading of several amplifiers in a chain, or simply to provide

complement outputs of the input logic function.

P SUFFIX

PLASTIC PACKAGE

CASE 648–08

FN SUFFIX

PLCC

CASE 775–02

= 100 mW typ/pkg (No Load)

= 1.8 ns typ (Single ended)

= 1.5 ns typ (Differential)

t , t = 1.5 ns typ (20%–80%)

r f

DIP

PIN ASSIGNMENT

CC2

CC1

LOGIC DIAGRAM

OUT

= PIN 1

= PIN 16

= PIN 8

CC1

CC2

Pin assignment is for Dual–in–Line Package.

For PLCC pin assignment, see the Pin Conversion

Tables on page 6–36 of the Motorola MECL Data

Book (DL122/D).

to be used to supply bias to the MC10216 only and bypassed (when used)

with 0.01 µF to 0.1 µF capacitor.

When the input pin with bubble goes positive, it’s respective output pin with bubble

goes positive.

3/93

Motorola, Inc. 1996

REV 5

3–197

MC10216

ELECTRICAL CHARACTERISTICS

Test Limits

+25°C

Typ

Under

Test

–30°C

+85°C

Characteristic

Power Supply Drain Current

Input Current

Symbol

Unit

mAdc

µAdc

Min

Max

Min

Max

Min

Max

180

115

inH

1.5

1.0

CBO

Output Voltage

Logic 1

–1.060

–0.890

–0.960

–0.810

–0.890

–0.700

Vdc

Output Voltage

Logic 0

Logic 1

Logic 0

–1.890

–1.675

–1.850

–1.650

–1.825

–1.615

Threshold Voltage

Reference Voltage

OHA

–1.080

–0.980

–0.910

OLA

–1.655

–1.630

–1.595

–1.420

–1.280

–1.350

–1.230

–1.295

–1.150

Vdc

Switching Times (50Ω Load)

Propagation Delay

1.0

2.6

1.0

1.8*

2.5

1.0

2.8

4+2+

4–2–

4+3–

4–3+

Rise Time

Fall Time

(20 to 80%)

1.0

2.6

1.0

1.5

2.5

1.0

2.8

1.0

2.6

1.0

1.5

2.5

1.0

2.8

2–

3–

* Delay is 1.5ns when inputs are driven differentially.

Delay is 1.8ns when inputs are driven single ended.

MOTOROLA

3–198

MECL Data

DL122 — Rev 6

MC10216

ELECTRICAL CHARACTERISTICS (continued)

TEST VOLTAGE VALUES (Volts)

@ Test Temperature

ILmin

IHmax

IHAmin

ILAmax

–30°C –0.890

+25°C –0.810

+85°C –0.700

–1.890

–1.850

–1.825

–1.205

–1.105

–1.035

–1.500

–1.475

–1.440

–5.2

From

Under

Test

TEST VOLTAGE APPLIED TO PINS LISTED BELOW

)

Characteristic

Power Supply Drain Current

Input Current

Symbol

Gnd

ILmin

IHmax

IHAmin

ILAmax

4, 9, 12

5, 10, 13

1, 16

9, 12

inH

9, 12

4, 12

5, 10, 13

8, 4

8, 9

CBO

Output Voltage

Logic 1

Logic 0

Logic 1

Logic 0

9, 12

5, 10, 13

1, 16

Output Voltage

9, 12

5, 10, 13

1, 16

Threshold Voltage

Reference Voltage

OHA

9, 12

5, 10, 13

1, 16

9, 12

OLA

5, 10, 13

1, 16

5, 10, 13

1, 16

Pulse Out

Switching Times

(50Ω Load)

Pulse In

–3.2 V

+2.0 V

Propagation Delay

5, 10, 13

1, 16

4+2+

4–2–

4+3–

4–3+

Rise Time

Fall Time

(20 to 80%)

5, 10, 13

1, 16

5, 10, 13

1, 16

2–

3–

Each MECL 10,000 series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been

established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained.

Outputs are terminated through a 50–ohm resistor to –2.0 volts. Test procedures are shown for only one gate. The other gates are tested in the

same manner.

MECL Data

3–199

MOTOROLA

DL122 — Rev 6

MC10216

OUTLINE DIMENSIONS

FN SUFFIX

PLASTIC PLCC PACKAGE

CASE 775–02

ISSUE C

0.007 (0.180)

L–M

Y BRK

–M–

–N–

0.007 (0.180)

L–M

–L–

0.010 (0.250)

L–M

VIEW D–D

0.007 (0.180)

L–M

0.007 (0.180)

L–M

0.004 (0.100)

–T– SEATING

PLANE

0.007 (0.180)

L–M

VIEW S

0.010 (0.250)

L–M

NOTES:

1. DATUMS –L–, –M–, AND –N– DETERMINED

INCHES

MILLIMETERS

DIM

MIN

MAX

0.395

0.180

0.110

0.019

MIN

9.78

4.20

2.29

0.33

MAX

10.03

4.57

2.79

0.48

WHERE TOP OF LEAD SHOULDER EXITS PLASTIC

BODY AT MOLD PARTING LINE.

0.385

0.165

0.090

0.013

2. DIMENSION G1, TRUE POSITION TO BE

MEASURED AT DATUM –T–, SEATING PLANE.

3. DIMENSIONS R AND U DO NOT INCLUDE MOLD

FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250)

PER SIDE.

4. DIMENSIONING AND TOLERANCING PER ANSI

Y14.5M, 1982.

5. CONTROLLING DIMENSION: INCH.

6. THE PACKAGE TOP MAY BE SMALLER THAN THE

PACKAGE BOTTOM BY UP TO 0.012 (0.300).

DIMENSIONS R AND U ARE DETERMINED AT THE

OUTERMOST EXTREMES OF THE PLASTIC BODY

EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS,

GATE BURRS AND INTERLEAD FLASH, BUT

INCLUDING ANY MISMATCH BETWEEN THE TOP

AND BOTTOM OF THE PLASTIC BODY.

7. DIMENSION H DOES NOT INCLUDE DAMBAR

PROTRUSION OR INTRUSION. THE DAMBAR

PROTRUSION(S) SHALL NOT CAUSE THE H

DIMENSION TO BE GREATER THAN 0.037 (0.940).

THE DAMBAR INTRUSION(S) SHALL NOT CAUSE

THE H DIMENSION TO BE SMALLER THAN 0.025

(0.635).

0.050 BSC

1.27 BSC

0.026

0.020

0.025

0.350

0.042

–––

0.032

–––

0.356

0.048

0.056

0.020

0.66

0.51

0.64

8.89

1.07

–––

0.81

–––

9.04

1.21

1.42

0.50

0.310

0.040

0.330

–––

7.88

1.02

8.38

–––

MOTOROLA

3–200

MECL Data

DL122 — Rev 6

MC10216

OUTLINE DIMENSIONS

L SUFFIX

CERAMIC DIP PACKAGE

CASE 620–10

–A–

NOTES:

ISSUE V

1. DIMENSIONING AND TOLERANCING PER

ANSI Y14.5M, 1982.

2. CONTROLLING DIMENSION: INCH.

3. DIMENSION L TO CENTER OF LEAD WHEN

FORMED PARALLEL.

4. DIMENSION F MAY NARROW TO 0.76 (0.030)

WHERE THE LEAD ENTERS THE CERAMIC

BODY.

–B–

INCHES

MILLIMETERS

DIM

MIN

MAX

0.785

0.295

0.200

0.020

MIN

19.05

6.10

–––

MAX

19.93

7.49

5.08

0.50

0.750

0.240

–––

–T–

SEATING

PLANE

0.015

0.39

0.050 BSC

1.27 BSC

0.055

0.065

1.40

1.65

0.100 BSC

2.54 BSC

0.008

0.125

0.015

0.170

0.21

3.18

0.38

4.31

16 PL

0.25 (0.010)

0.300 BSC

7.62 BSC

D 16 PL

0.25 (0.010)

0.020

0.040

0.51

1.01

P SUFFIX

PLASTIC DIP PACKAGE

CASE 648–08

ISSUE R

NOTES:

–A–

1. DIMENSIONING AND TOLERANCING PER ANSI

Y14.5M, 1982.

2. CONTROLLING DIMENSION: INCH.

3. DIMENSION L TO CENTER OF LEADS WHEN

FORMED PARALLEL.

4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.

5. ROUNDED CORNERS OPTIONAL.

INCHES

MILLIMETERS

DIM

MIN

MAX

0.770

0.270

0.175

0.021

0.70

MIN

18.80

6.35

3.69

0.39

1.02

MAX

19.55

6.85

4.44

0.53

1.77

0.740

0.250

0.145

0.015

0.040

SEATING

–T–

0.100 BSC

0.050 BSC

2.54 BSC

1.27 BSC

PLANE

0.008

0.015

0.130

0.305

0.21

0.38

3.30

7.74

0.110

0.295

2.80

7.50

D 16 PL

0.25 (0.010)

0.020

0.040

0.51

1.01

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding

the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and

specificallydisclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola

datasheetsand/orspecificationscananddovaryindifferentapplicationsandactualperformancemayvaryovertime. Alloperatingparameters,including“Typicals”

must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of

others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other

applicationsintended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury

ordeathmayoccur. ShouldBuyerpurchaseoruseMotorolaproductsforanysuchunintendedorunauthorizedapplication,BuyershallindemnifyandholdMotorola

and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees

arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that

Motorola was negligent regarding the design or manufacture of the part. Motorola and

Opportunity/Affirmative Action Employer.

are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal

How to reach us:

USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;

JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,

P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454

3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315

MFAX: RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609

INTERNET: http://Design–NET.com

ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,

51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298

MC10216/D

◊

MECL Data

DL122 — Rev 6

3–201

MOTOROLA

MC10216LS [MOTOROLA]

相关型号：

MC10216P

MC10216P

MC10216PD

MC10216PDS

MC10216PS

MC10216_02

MC10231

MC10231FN

MC10231FN

MC10231FNR2

MC10231L

MC10231L