K7802T-1000 [MORNSUN]
WIDE INPUT, NON-ISOLATED & REGULATED SMD PACKAGE SINGLE OUTPUT; 宽电压输入,非隔离稳压SMD封装,单路输出![K7802T-1000](http://pdffile.icpdf.com/pdf1/p00191/img/icpdf/K7802T_1078389_icpdf.jpg)
型号: | K7802T-1000 |
厂家: | ![]() |
描述: | WIDE INPUT, NON-ISOLATED & REGULATED SMD PACKAGE SINGLE OUTPUT |
文件: | 总5页 (文件大小:444K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
K78XXT-1000 Series
WIDE INPUT, NON-ISOLATED & REGULATED
SMD PACKAGE SINGLE OUTPUT
Patent Protection RoHS
FEATURES
PRODUCT PROGRAM
Input
Current
(mA)
Output
Current
(mA)
Input Voltage (V)
Output Voltage (V)
Efficiency (%)(typ.)
Vin (min.) Vin(max.)
● Efficiency up to 92%
● No heatsink required
Part Number
Nominal Range
Normal Adjust Range
● 1.0AMP SMD package
● Super low ripple and noise
● Adjustable output voltage
● Remote ON/OFF control
● Short circuit protection
● Low control current
K7801T-1000*
K78X2T-1000*
K7802T-1000*
K7803T-1000
K7805T-1000
K78X6T-1000*
12
12
12
12
12
12
5.0-18
5.0-18
5.0-18
5.0-18
7.0-18
8.5-18
165
190
245
320
460
580
1.5
1.8
2.5
3.3
5.0
6.5
fixed
1.5-3.6
1.5-3.9
1.8-5.5
2.5-6.5
fixed
1000
1000
1000
1000
1000
1000
76
78
82
84
90
92
73
75
82
84
88
91
● Operating temperature: -40°C ~ +85°C
Note:To adjust the output voltage must be met Vin-Vo>2V. *Designing. Input Current measured at nominal
input voltage and rated output load.
INPUT SPECIFICATIONS
Item
Test Conditions
Min. Typ. Max. Units
Input Filter
Start Current(RMS)
Capacitor (10μF)
APPLICATIONS
0.95 1.1
A
The K78XXT-1000 series with high efficiency
OUTPUT SPECIFICATIONS
switching regulators are ideally supply for
space constrained mobile applications. there
is no need for any heatsinks. The additional
features include remote ON/OFF control and
adjustable output voltage. Super low ripple
and noise of typically only 20mV and Low
control current.
Item
Test Conditions
Min. Typ. Max. Units
±2 ±3
Output Voltage Accuracy
Line Regulation
Load Regulation
Input voltage range at full load
%
±0.2 ±0.5
±0.4 ±1.0
Nominal input,10% to 100% load
20MHz bandwidth
20
10
35
15
Ripple and Noise*
mVp-p
20MHz bandwidth
(refer to Figure 6)
Short Circuit Protection Mode Hiccup Mode
Short Circuit Protection
Inside Wasted
Continuous, automatic recovery
0.5
W
°C
Thermal Shutdown
Internal IC junction
150
1.8
1.4
Output current limit
Switching Frequency
Transient peak deviation
Transient recovery time
Quiescent current
A
PWM type
MHz
MODEL SELECTION
K7805T-1000
±75 ±100 mV
Input voltage range,10% to
100% load
100
3
μS
1
mA
Output Current
Package Style
Output Voltage
Product Series
Temperature Coefficient
Max Capacitance Load
-40°C ~ +85°C ambient
±0.02 %/°C
1000 μF
ON
Open or 1.2<Vc<6V
Vc<0.6V
Remote ON/OFF
OFF
ON: Open or 1.2<Vc≤6V
OFF:GND or Vc<0.4V
ON/OFF Control Current
Shutdown Input Current
100 200
μA
120 200
*Test ripple and noise by “parallel cable” method.
MORNSUN Science & Technology Co.,Ltd.
Address: No. 5, Kehui St. 1, Kehui development
center, Science Ave., Guangzhou Science City,
Luogang district, Guangzhou,P.R.China.
Tel: 86-20-28203030
COMMON SPECIFICATIONS
Item
Test Conditions
Min. Typ. Max. Units
Storage humidity Range
95
%
Fax:86-20-28203068
Http://www.mornsun-power.com
Operating Temperature Range Power derating(above 71°C)
-40
-55
+85
Storage Temperature Range
Operating Case Temperature
+125
+100
oC
Lead Temperature
Cooling
1.5mm from case for 10 seconds
260
Free Air Convection
The copyright and authority for the interpretation of the products are reserved by MORNSUN
Specifications subject to change without notice.
K78XXT-1000
A/0-2011
Page 1 of 5
COMMON SPECIFICATIONS
TYPICAL TEMPERATURE CURVE
Item
Test Conditions
Min.
Typ.
Plastic (UL94-V0)
k hours
Max. Units
Case Material
MTBF
(MIL-HDBK-217F,+25°C)
1000
Hop swap
Thermal resistance
Weight
Not supported
Temperature Derating Graph
120
90
℃/W
2.3
g
100
80
EMC SPECIFICATIONS
EN55022, CLASS A(without external circuit)
60
CE
Safe Operating Area
EN55022, CLASS B(refer to Figure 4)
EN55022, CLASS A(refer to Figure 5)
40
RE
20
0
ESD
EFT
Surge
IEC/EN61000-4-2
IEC/EN61000-4-4
IEC/EN61000-4-5
Air ±8KV / Contact ±6KV perf. Criteria B
±2KV
±2KV
perf. Criteria B
-40
0
40
71 85
120
Operating Temp.(°C )
perf. Criteria B(refer to Figure 4)
(Figure2)
TYPICAL APPLICATION CIRCUIT
Vin
Vout
K7805T-1000 5
1
7,9
10
6
RECOMMENDED REFLOW SOLDERING PROFILE
R1
R2
C1
C2
250
Peak.Temp 240 C
10 Sec M ax
ON/OFF
220 C
C4
470pF
200
90 Sec Max
GND
GND
(>220 C)
150
(Figure 1)
1. C1, C2 is required for best performance and should be fitted close to the converter
pins.
100
50
2. The capacitance of C1, C2 sees external capacitor table, it can be increased properly if
required, and tantalum or low ESR electrolytic capacitors may also suffice.
3. No parallel connection or plug and play.
0
Time (sec.)
(Figure 3)
EXTERNAL CAPACITOR TABLE
C1
(Ceramic
Capacitor)
C2
(Ceramic
Capacitor)
Part
Number
K7803T-1000
K7805T-1000
10μF/25V
10μF/25V
22μF/16V
22μF/16V
ADJUSTMENT RESISTOR VALUES
Part Number
K7803T-1000
3.3(V)
K7805T-1000
5.0(V)
R1(KΩ)
Vo (nominal)
Vadj(V)
1.8
R1(KΩ)
R2(KΩ)
R2(KΩ)
15.4
-
-
-
9.7
30.5
48.8
75
115
338
1835
-
-
2.5
87
-
3.0
339
-
-
3.3
-
-
-
-
-
-
-
-
-
-
-
-
3.6
121
51.0
16.6
8.0
6.5
5.2
1.1
-
-
3.9
-
-
4.5
4.9
-
5.0
-
5.1
-
426
58.7
16.9
3.2
5.5
-
6.0
-
6.5
-
-
The R1, R2 in the above table are used to set the output voltage. If no need to adjust the output voltage, connect a ceramic capacitor to
GND with 470pF typical value for increase immunity. Insure the output voltage is in the adjust range or else may cause permanent damage to the
device. Fine-tune output voltage must appease Vin-Vo>2V.
The copyright and authority for the interpretation of the products are reserved by MORNSUN
Specifications subject to change without notice.
K78XXT-1000 A/0-2011 Page 2 of 5
EMC RECOMMENDED CIRCUIT
L1
+Vin
+Vo
K7805T-1000 5
1
7,9
10
6
C1
TVS
RL
ON/OFF
C2
470pF
GND
GND
(Figure 4)
Specifications:TVS:SMCJ18A,1500W;L1:68µH;C1:680µF/50V electrolytic capacitors。
+Vin
L2
+Vo
K7805T-1000 5
1
7,9
6
10
C3
RL
ON/OFF
C4
470pF
GND
GND
(Figure 5)
Specifications:L2:516µH;C3:1µF/50V ceramic capacitor。
TEST CONFIGURATIONS (TA=25°C)
1
Efficiency and Output Voltage Ripple Test
25.4mm
25.4mm
12.7mm
+Vout
DC/DC
Converter
Copper strip
Vin
5
1
10μF
7, 9
6
1μF
C1
C2
Scope
470pF
Ceramic
C4
Copper strip
GND
(Figure 6)
2
Start-up and Load Transient Response Test
50.8 mm
+Vout
DC/DC
Converter
Copper strip
Vin
5
1
C2
7,9
6
C1
Scope
470pF
Ceramic
C4
GND
Copper strip
(Figure 7)
APPLICATION EXAMPLE
L
+Vout
DC/DC
Converter
Vin
5
1
7,9
6
C1
C2
22μ F
C4
470pF
GND
(Figure 8)
To reduce output ripple, it is recommended to add a LC filter to output port.
L: Recommended parameter 10μH ~ 47μH.
The copyright and authority for the interpretation of the products are reserved by MORNSUN
Specifications subject to change without notice.
K78XXT-1000 A/0-2011 Page 3 of 5
CHARACTERISTIC CURVE
Efficiency
Ripple
Ripple VS.Vin(full load)
Efficiency VS.Vin(full load)
30
25
20
15
10
5
92
90
88
86
84
82
80
K7803T-1000
K7805T-1000
K7803T-1000
K7805T-1000
0
5
6
7
8
9
10 11 12 13 14 15 16 17 18
5
6
7
8
9
10 11 12 13 14 15 16 17 18
Vin(V)
Vin(V)
Efficiency VS.Load(Vin=Vin-nominal)
Ripple VS.Load(Vin=Vin-nominal)
25
92
90
88
86
84
82
80
78
76
74
20
15
10
5
K7803T-1000
K7805T-1000
K7803T-1000
K7805T-1000
0
0
100 200 300 400 500 600 700 800 900 1000
0
100 200 300 400 500 600 700 800 900 1000
Load(mA)
Load(mA)
EMC TESTING WAVE SHAPE
CE(without external circuit)
CE(refer to Figure 4)
The copyright and authority for the interpretation of the products are reserved by MORNSUN
Specifications subject to change without notice.
K78XXT-1000 A/0-2011 Page 4 of 5
OUTLINE DIMENSIONS & RECOMMENDED FOOTPRINT &PACKAGING
RECOMMENDED FOOTPRINT
MECHANICAL DIMENSIONS
(Side View)
2.54 [0.100]
1.80 [0.071]
10
1
9
7
6
5
7.00 [0.276]
7.25 [0.285]
A
2.54 [0.100]
2.54 [0.100]
1.00 [0.039]
A
10 9
6
5
7
0.25 [0.010]
8.50 [0.335]
12.10 [0.476]
(Top View)
1
FOOTPRINT DETAILS
5°max
1.13 [0.044]
Pin
1
10.16
[0.400]
Function
Vin
15.24 [0.600]
GND
7,9
5
Vout
Note:
Unit:mm[inch]
Vadj
6
Pin tolerances:
General tolerances:
±
0.10mm[
±
0.004inch]
10
ON/OFF
±
0.25mm[±0.010inch]
TUBE OUTLINE DIMENSIONS
TAPINGREEL DIMENSIONS
Taping dimension:
1.75 [0.069]
11.50 [0.453]
∅1.50 [0.059]
2.00 [0.079]
0.50 [0.020]
14.70[0.579]
10.20[0.402]
12.40
[0.488]
16.00
[0.630]
∅1.50 [0.059]
7.65 [0.301]
29.40 [1.157]
Taping reel dimension:
6.50 [0.256]
5.60 [0.220]
∅100.00[3.937]
Note:
Unit :mm[inch]
General tolerances: ±0.50mm[±0.020inch]
L=530mm[20.866inch] Devices per tube quantity: 33pcs
L=220mm[8.661inch] Devices per tube quantity: 13pcs
Short tube inner packaging dimensions: L*W*H=255*170*80mm;
Short tube outer packaging dimensions(with six inner packaging boxes):
L*W*H=375*280*270mm;
Long tube inner packaging dimensions: L*W*H=580*200*100mm;
Long tube outer packaging dimensions(with two inner packaging boxes):
L*W*H=600*215*220mm;
∅
13.00 [0.512]
∅21.50 [0.846]
Note:
Unit :mm[inch]
General tolerances: ±0.50mm[±0.020inch]
Devices per reel quantity:500pcs
Inner packaging dimensions: L*W*H=365*350*105mm;
Devices per tube quantity: 2000pcs
Outer packaging dimensions: L*W*H=390*360*245mm.
Devices per tube quantity: 4000pcs
Long tube outer packaging dimensions(with three inner packaging boxes):
L*W*H=600*215*325mm.
Note:
1. All specifications measured at Ta=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified.
2. In this datasheet, all the test methods of indications are based on corporate standards.
The copyright and authority for the interpretation of the products are reserved by MORNSUN
Specifications subject to change without notice.
K78XXT-1000 A/0-2011 Page 5 of 5
相关型号:
©2020 ICPDF网 联系我们和版权申明