SL2524 [MITEL]
1.3GHz Dual Wideband Logarithmic Amplifier; 1.3GHz的双宽带对数放大器
| 型号： | SL2524 |
| 厂家： | 
MITEL NETWORKS CORPORATION |
| 描述： | 1.3GHz Dual Wideband Logarithmic Amplifier |
| 文件： | 总17页 (文件大小：379K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SL2524
1.3GHz Dual Wideband Logarithmic Amplifier
DS4548 - 2.1 July 1995
The SL2524 is a pin compatible replacement for the
SL2521 and SL2522 series of log amplifiers, and exhibits a
superior stability performance. The amplifier is a successive
detection type which provides linear gain and accurate loga-
rithmic signal compression over a wide bandwidth. The two
stages can be operated independently.
When six stages (three SL2524s) are cascaded the strip
can be used for IFs between 30-650MHz whilst achieving
greater than 65dB dynamic range with a log accuracy of
<±1.0dB. The balanced limited output also offers accurate
phase information with input amplitude.
FEATURES
■
■
■
■
■
■
1.3GHz Bandwidth (-3dB)
Balanced IF limiting
3ns Rise Times/5ns Fall Times (six stages)
20ns Pulse Handling (six stages)
Temperature Stabilised
Surface Mountable
APPLICATIONS
■
■
■
Ultra Wideband Log Receivers
Channelised Receivers
Monopulse Applications
OPTIONAL PIN
REFERENCE
ABSOLUTE MAXIMUM RATINGS
Supply Voltage (VCC above VEE)
Storage temperature
+7.0V
-65°C to +150°C
Operating temperature range
SL2524/B/LC
SL2524/C/HP
Junction temperature - LC20
- HP20
-40°C to +85°C
-30°C to +85°C
+175°C
+150°C
PIN DESCRIPTION
PIN DESCRIPTION
Applied DC voltage to RF input ±0.4V (between RF I/P
pins)
+15dBm
NOT less than 180Ω
1
2
3
4
5
6
7
8
9
10
SUB VEE
11
12
13
14
15
16
17
18
19
20
N/C
Applied RF power to RF input
Value of RSET resistors
Thermal resistance:-
IF OUTPUT (A)
IF OUTPUT (A)
VEE (A)
OUTPUT VC (A)
IF INPUT (A)
IF INPUT (A)
VCC (A)
R SET (B)
DET. OUTPUT (B)
VCC (B)
Die to case
-LC 20
- HP20
28°C/W
20°C/W
73°C/W
82°C/W
IF OUTPUT (B)
IF OUTPUT (B)
OUTPUT VCC (B)
VEE (B)
IF INPUT (B)
IF INPUT (B)
Die to ambient - LC20
- HP20
DET. OUTPUT (A)
R SET (A)
ORDERING INFORMATION
SL2524/B/LC (Ceramic leadless chip carrier package)
SL2524/C/HP (Plastic J lead chip carrier package)
SL2524/NA/1C (DC probe tested bare die)
5962 - 92315 (SMD)
Fig.1 Pin connections top view
SL2524
Fig.2 Circuit diagram of single stage A - (stage B pin Nos bracketed)
Fig.3 Pad map for SL2524 naked die
2
SL2524
ELECTRICAL CHARACTERISTICS - SL2524B
Guaranteed at the following test conditions unless otherwise stated
Frequency = 200MHz, Tamb = +25°C, Input power = -30dBm, VCC = 6V ±0.1V, Source Impedance = 50Ω.
Load impedance = 50Ω, Test Circuit = Fig. 4, RSET = 300Ω. Tested as a dual stage.
Value
Units
Characteristic
Supply current
Conditions
Min
70
Typ
87
Max
100
mA
dB
T
amb = +25°C f = 25MHz See Notes 1, 3
Small signal gain (dual stage,
single ended)
9.6
11.4
13.0
dB
dB
dB
T
T
T
amb = -40°C f = 200MHz See Notes 2, 3
amb = +25°C f = 200MHz See Note 3
amb = +85°C f = 200MHz See Notes 2, 3
10.1
9.9
9.5
11.6
11.3
11.0
13.1
12.7
12.5
T
T
T
amb = -40°C f = 500MHz See Notes 2, 3
amb = +25°C f = 500MHz See Note 3
amb = +85°C f = 500MHz See Notes 2, 3
dB
dB
dB
9.7
9.3
8.2
11.2
10.7
9.7
12.7
12.1
11.2
mA
mA
T
amb = +25°C, VIN = 0dBm, f = 25MHz
Detected output current (max)
3.20
3.05
3.45
3.25
3.70
3.45
See Note 1
T
amb = -40°C, VIN = 0dBm, f = 200MHz
See Note 2
mA
mA
T
T
amb = +25°C, VIN = 0dBm, f = 200MHz
amb = +85°C, VIN = 0dBm, f = 200MHz
3.15
3.10
3.30
3.30
3.45
3.50
See Note 2
T
amb = -40°C, VIN = 0dBm, f = 500MHz
mA
2.80
3.10
3.30
See Note 2
mA
mA
T
T
amb = +25°C, VIN = 0dBm, f = 500MHz
amb = +85°C, VIN = 0dBm, f = 500MHz
2.90
2.85
3.15
3.10
3.45
3.65
See Note 2
T
T
T
amb = -40°C, See Note 2
amb = +25°C, See Note 2
amb = +85°C, See Note 2
mA
mA
mA
Detected output current
(no signal)
0.85
0.80
0.80
0.95
0.93
0.90
1.15
1.10
1.10
MHz
MHz
MHz
-3dB w.r.t 200MHz, Tamb = -40°C
See Note 2
Upper cut off frequency (RF)
600
900
600
1100
1100
800
-3dB w.r.t 200MHz, Tamb = +25°C
-3dB w.r.t 200MHz, Tamb = +85°C
See Note 2
MHz
MHz
mV
-3dB w.r.t 200MHz, Tamb = +25°C
50% O/P current w.r.t. 200MHz
I/P power = 0dBm, Tamb = +25°C
Lower cut off frequency (RF)
Detector cut off frequency
Limited IF O/P voltage
0.35
700
1
135
155
175
Degree Frequency = 70MHz, -55 to +3dBm
See Note 2
Phase variation with input level
(normalised to -30dBm)
0±2.0
0±3.0
Frequency = 200MHz, -55 to +3dBm
See Note 2
Degree
-4.0±2.0 -4.0±3.0
mV
dB
See Note 1
Limited O/P var with temp.
Noise figure
±12
14
15
1
±25
dBm
kΩ
Max I/P before overload
Input impedance
1kΩ in parallel with 2pF
Ω
Output impedance
50
NOTES
1. Parameter guaranteed but not tested
2. Tested at 25°C only, but guaranteed at temperature
3. Gain will typically increase by 6dB, when RF outputs use 1kΩ loads in place of 50Ω
3
SL2524
ELECTRICAL CHARACTERISTICS - SL2524C
Guaranteed at the following test conditions unless otherwise stated
Frequency = 200MHz, Tamb = +25°C, Input power = -30dBm, VCC = 6V ±0.1V, Source Impedance = 50Ω.
Load impedance = 50Ω, Test Circuit = Fig. 4, RSET = 300Ω. Tested as a dual stage.
Value
Units
Characteristic
Supply current
Conditions
Min
70
Typ
87
Max
100
mA
dB
T
amb = +25°C f = 25MHz See Note 3
Small signal gain (dual stage,
single ended)
9.6
11.4
13.0
T
T
T
amb = -30°C f = 200MHz See Notes 2, 3
amb = +25°C f = 200MHz See Note 3
amb = +85°C f = 200MHz See Notes 2, 3
dB
dB
dB
9.6
9.4
9.0
11.6
11.3
11.0
13.6
13.2
13.0
dB
dB
dB
T
T
T
amb = -30°C f = 500MHz See Notes 1, 3
amb = +25°C f = 500MHz See Note 1
amb = +85°C f = 500MHz See Notes 1, 3
9.2
8.8
7.7
11.2
10.7
9.7
13.2
12.6
11.7
mA
mA
T
T
amb = +25°C, VIN = 0dBm, f = 25MHz
amb = -30°C, VIN = 0dBm, f = 200MHz
3.20
2.95
3.45
3.25
3.70
3.55
Detected output current (max)
See Note 2
mA
mA
T
T
amb = +25°C, VIN = 0dBm, f = 200MHz
amb = +85°C, VIN = 0dBm, f = 200MHz
3.05
3.00
3.30
3.30
3.55
3.50
See Note 2
mA
mA
mA
T
amb = -30°C, VIN = 0dBm, f = 500MHz
2.70
2.80
2.75
3.10
3.15
3.10
3.30
3.55
3.75
See Note 1
T
amb = +25°C, VIN = 0dBm, f = 500MHz
See Note 1
T
amb = +85°C, VIN = 0dBm, f = 500MHz
See Note 1
mA
mA
mA
T
T
T
amb = -30°C, See Note 2
amb = +25°C, See Note 2
amb = +85°C, See Note 2
0.75
0.70
0.70
0.95
0.93
0.90
1.25
1.20
1.20
Detected output current
(no signal)
-3dB w.r.t 200MHz, Tamb = +25°C
See Note 1
MHz
Upper cut off frequency (RF)
1000
MHz
MHz
mV
-3dB w.r.t 200MHz, Tamb = +25°C
50% O/P current w.r.t. 200MHz
I/P power = 0dBm, Tamb = +25°C
Lower cut off frequency (RF)
Detector cut off frequency
Limited IF O/P voltage
0.35
600
2
105
135
175
Degree Frequency = 70MHz, -55 to +3dBm
See Note 1
Phase variation with input level
(normalised to -30dBm)
0±2.0
-4.0±2.0
Frequency = 200MHz, -55 to +3dBm
See Note 1
Degree
mV
dB
See Note 1
Limited O/P var with temp.
Noise figure
±12
14
15
1
±25
dBm
kΩ
Max I/P before overload
Input impedance
1kΩ in parallel with 2pF
Ω
Output impedance
50
NOTES
1. Parameter guaranteed but not tested
2. Tested at 25°C only, but guaranteed at temperature
3. Gain will typically increase by 6dB, when RF outputs use 1kΩ loads in place of 50Ω
4
SL2524
GENERAL DESCRIPTION
The detector is full wave and good slew rates are achieved
with 2ns rise and 5ns fall times (no video filter). The video
bandwidth of a six stage strip is typically 600MHz (-3dB).
The amplifier also offers balanced IF limiting, low phase
shift versus input amplitude, and at an IF of 120MHz, less than
5° of phase change is achievable over the input level of
-55dBm to +5dBm.
The IF and Video ports can be used simultaneously, so
offering phase, frequency and pulse (video) information. A
slight loss of dynamic range (2dB) will be observed when the
IF ports are used in conjunction with the video.
The SL2524 is primarily intended for use in Radar and EW
receivers. Sixstages(3chipcarriers)canbecascadedtoform
a very wideband logarithmic ampifier offering >65dB of input
dynamic range, with pulse handling of better than 25ns. (See
figs 5 and 6.)
A six stange strip also offers balanced IF limiting, linearity
(log accuracy) of < ±1.0dB, temperature stabilisation and
programmable detector characteristics.
The detector has an external resistor set (RSET) pin which
allows the major characteristics of the detector to be
programmed. With six stage strip it is possible to vary the
value of RSET on each detector and so improve the overall log
error/linearity.
Fig.4 Test circuit
Fig.5 Schematic diagram showing configuration of SD Log strip
5
SL2524
Fig.6 Circuit diagram for 6-log strip (results shown in figs. 11 to 24 were achieved with this circuit)
Typical characteristics for a dual - stage amplifier (i.e. One SL2524)
Fig.7 IF Gain vs frequency of 2 amplifiers (One SL2524)
6
SL2524
Typical characteristics for a dual - stage amplifier (i.e. One SL2524) cont.
Fig.8 Normalised phase vs CW input level at 50, 250 and 450MHz for 50Ω O/P termination (25°C)
Fig.9 Detector current vs RSET at 200MHz (25°C)
7
SL2524
Typical characteristics for a dual - stage amplifier (i.e. One SL2524) cont.
Fig.10 Detector current vs frequency at RSET = 200Ω and 500Ω (25°C)
Typical characteristics for a six stage strip, using detected output (Ref. figs 5 & 6)
Fig.11 Detector bandwidth (25°C)
8
SL2524
Typical characteristics for a six stage strip, using detected output (Ref. figs 5 & 6) cont.
0
Fig.12 Detected O/P vs CW input at 60, 125, 450 and 600MHz at 25°C
Fig.13 Detected O/P vs CW input level and temperature at 60 and 125MHz
9
SL2524
Typical characteristics for a six stage strip, using detected output (Ref. figs 5 & 6) cont.
Fig.14 Detected O/P vs CW input level at 450MHz across temperature
Fig.15 Typical log linearity of detected output measured at 450MHz (25°C)
10
SL2524
Typical characteristics for a six stage strip as a low phase shift wideband limiter (Ref. figs 5 & 6)
Fig.16 IF limiting characteristics at 60MHz and 500MHz (25°C)
Fig.17 IF limiting characteristic at 60MHz across temperature
11
SL2524
Typical characteristics for a six stage strip as a low phase shift wideband limiter (Ref. figs 5 & 6)
Fig.18 IF limiting characteristic at 500MHz across temperature
Fig.19 Small signal gain vs frequency across temperature
12
SL2524
Typical characteristics for a six stage strip as a low phase shift wideband limiter (Ref. figs 5 & 6)
Fig.20 Phase deviation vs CW input level (normalised at -30dBm) at 25°C
across input frequency
Fig.21 Phase deviation vs CW input level (normalised at -30dBm) at 50MHz
across temperature
13
SL2524
Typical characteristics for a six stage strip as a low phase shift wideband limiter (Ref. figs 5 & 6)
Fig.22 Phase deviation vs CW input level (normalised at -30dBm) at 450MHz
across temperature
Fig.23 Peak phase deviation over -65dBm → +10dBm CW input level vs CW input frequency.
Across temperature
14
http://www.mitelsemi.com
World Headquarters - Canada
Tel: +1 (613) 592 2122
Fax: +1 (613) 592 6909
North America
Tel: +1 (770) 486 0194
Fax: +1 (770) 631 8213
Asia/Pacific
Tel: +65 333 6193
Fax: +65 333 6192
Europe, Middle East,
and Africa (EMEA)
Tel: +44 (0) 1793 518528
Fax: +44 (0) 1793 518581
Information relating to products and services furnished herein by Mitel Corporation or its subsidiaries (collectively “Mitel”) is believed to be reliable. However, Mitel assumes no
liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of
patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or
service conveys any license, either express or implied, under patents or other intellectual property rights owned by Mitel or licensed from third parties by Mitel, whatsoever.
Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Mitel, or non-Mitel furnished goods or services may infringe patents or
other intellectual property rights owned by Mitel.
This publication is issued to provide information only and (unless agreed by Mitel in writing) may not be used, applied or reproduced for any purpose nor form part of any order or
contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this
publication are subject to change by Mitel without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or
service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific
piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or
data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in
any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Mitel’s
conditions of sale which are available on request.
M Mitel (design) and ST-BUS are registered trademarks of MITEL Corporation
Mitel Semiconductor is an ISO 9001 Registered Company
Copyright 1999 MITEL Corporation
All Rights Reserved
Printed in CANADA
TECHNICAL DOCUMENTATION - NOT FOR RESALE
相关型号：
SL2524/B/LC
Log Or Antilog Amplifier, 2 Func, 1099.65MHz Band Width, BIPolar, CQCC20, CERAMIC, LCC-20
ZARLINK
SL2524/C/HP
Log Or Antilog Amplifier, 2 Func, 999.65MHz Band Width, BIPolar, PQCC20, PLASTIC, LCC-20
ZARLINK
©2020 ICPDF网 联系我们和版权申明