W3EG7232S262AD4S [MICROSEMI]
DDR DRAM Module, 32MX72, 0.75ns, CMOS, SODIMM-200;型号: | W3EG7232S262AD4S |
厂家: | Microsemi |
描述: | DDR DRAM Module, 32MX72, 0.75ns, CMOS, SODIMM-200 动态存储器 双倍数据速率 |
文件: | 总14页 (文件大小:324K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
W3EG7232S-xAD4
-xBD4
White Electronic Designs
256MB – 32Mx72 DDR SDRAM UNBUFFERED w/PLL
FEATURES
DESCRIPTION
Double-data-rate architecture
The W3EG7232S is a 32Mx72 Double Data Rate
SDRAM memory module based on 256Mb DDR SDRAM
components. The module consists of nine 32Mx8 DDR
SDRAMs in 66 pin TSOP packages mounted on a 200
pin FR4 substrate.
DDR200, DDR266 and DDR300
• JEDEC design specifications
Bi-directional data strobes (DQS)
Differential clock inputs (CK & CK#)
Programmable Read Latency 2,2.5 (clock)
Programmable Burst Length (2,4,8)
Programmable Burst type (sequential & interleave)
Edge aligned data output, center aligned data input
Auto and self refresh
Synchronous design allows precise cycle control with the
use of system clock. Data I/O transactions are possible on
both edges and Burst Lengths allow the same device to be
useful for a variety of high bandwidth, high performance
memory system applications.
* This product is subject to change without notice.
Serial presence detect
Power supply: 2.5V ± 0.2V
JEDEC standard 200 pin SO-DIMM package
• Package height options:
AD4: 35.5 mm (1.38") and
BD4: 31.75 mm (1.25")
NOTE: Consult factory for availability of:
• RoHS compliant products
• Vendor source control options
• Industrial temperature option
OPERATING FREQUENCIES
DDR333 @CL=2.5
166MHz
DDR266 @CL=2
133MHz
DDR266 @CL=2.5
133MHz
DDR200 @CL=2
100MHz
Clock Speed
CL-tRCD-tRP
2.5-3-3
2-2-2
2.5-3-3
2-2-2
March 2007
Rev. 5
1
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
W3EG7232S-xAD4
-xBD4
White Electronic Designs
PIN CONFIGURATION
PIN NAMES
A0 – A12
BA0-BA1
DQ0-DQ63
CB0-CB7
Address input (Multiplexed)
Bank Select Address
Data Input/Output
Check bits
Pin
1
Symbol
VREF
VREF
VSS
Pin
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
Symbol
VSS
Pin
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
Symbol
A9
Pin
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
Symbol
DQ42
DQ46
DQ43
DQ47
VCC
2
VSS
AB
3
DQ19
DQ23
DQ24
DQ28
VCC
VSS
4
VSS
VSS
DQS0-DQS8 Data Strobe Input/Output
5
DQ0
DQ4
DQ1
DQ5
VCC
A7
CK0
Clock Input
6
A6
VCC
CK0#
CKE0
CS0#
RAS#
CAS#
WE#
Clock Input
7
A5
VCC
Clock Enable Input
Chip Select Input
Row Address Strobe
Column Address Strobe
Write Enable
8
VCC
A4
NC
9
DQ25
DQ29
DQS3
DQM3
VSS
A3
VSS
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
VCC
A2
NC
DQS0
DQM0
DQ2
DQ6
VSS
A1
VSS
A0
VSS
DQM0-DQM8 Data-In Mask
VCC
DQ48
DQ52
DQ49
DQ53
VCC
VCC
Power Supply
VSS
VCC
VCCQ
VSS
Power Supply for DQS
Ground
DQ26
DQ30
DQ27
DQ31
VCC
A10/AP
BA1
BA0
RAS#
WE#
CAS#
CS0#
NC
VSS
DQ3
DQ7
DQ8
DQ12
VCC
VREF
VCCSPD
SDA
Power Supply for Reference
Serial EEPROM Power Supply
Serial Data I/O
VCC
DQS6
DQM6
DQ50
DQ54
VSS
VCC
SCL
Serial Clock
CB0
CB4
CB1
CB5
VSS
SA0-SA2
VCCID
NC
Address in EEPROM
VCC Identification Flag
No Connect
VCC
DQ9
DQ13
DQS1
DQM1
VSS
NC
NC
VSS
VSS
DQ51
DQ55
DQ56
DQ60
VCC
VSS
VSS
DQS8
DQM8
CB2
CB6
VCC
DQ32
DQ36
DQ33
DQ37
VCC
VSS
DQ10
DQ14
DQ11
DQ15
VCC
VCC
DQ57
DQ61
DQS7
DQM7
VSS
VCC
VCC
CB3
CB7
NC
DQS4
DQM4
DQ34
DQ38
VSS
VCC
CK0
VCC
NC
VSS
CK0#
VSS
VSS
DQ58
DQ62
DQ59
DQ63
VCC
VSS
VSS
VSS
NC
DQ35
DQ39
DQ40
DQ44
VCC
VSS
VSS
DQ16
DQ20
DQ17
DQ21
VCC
NC
VCC
VCC
VCC
SDA
SA0
VCC
VCC
NC
DQ41
DQ45
DQS5
DQM5
VSS
SCL
VCC
CKE0
NC
SA1
DQS2
DQM2
DQ18
DQ22
VCCSPD
SA2
NC
A12
VCCID
NC
A11
VSS
March 2007
Rev. 5
2
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
W3EG7232S-xAD4
-xBD4
White Electronic Designs
FUNCTIONAL BLOCK DIAGRAM
CS0#
DQS0
DQM0
DQS4
DQM4
DM CS# DQS
DM CS# DQS
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQS1
DQM1
DQS5
DQM5
DM CS# DQS
DM CS# DQS
DQ8
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DQS2
DQM2
DQS6
DQM6
DM CS# DQS
DM CS# DQS
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQS3
DQM3
DQS7
DQM7
DM CS# DQS
DM CS# DQS
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQS8
DQM8
DDR SDRAM X 2
120
DM CS# DQS
DDR SDRAM X 2
DDR SDRAM X 2
DDR SDRAM X 2
DDR SDRAM X 1
CK0
CK0#
CB0
CB1
CB2
CB3
CB4
CB5
CB6
CB7
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
PLL
SERIAL PD
SCL
WP
SDA
A0 A1 A2
SA0 SA1 SA2
BA0, BA1: DDR SDRAMS
A0-A12: DDR SDRAMS
RAS#: DDR SDRAMS
CAS#: DDR SDRAMS
CKE0: DDR SDRAMS
WE#: DDR SDRAMS
BA0, BA1
A0-A12
RAS#
CAS#
CKE0
WE#
V
CCSPD
SPD/EEPROM
DDR SDRAMS
DDR SDRAMS
DDR SDRAMS
V
CC
VREF
VSS
Note: All resistor values are 22Ω unless otherwise indicated.
March 2007
Rev. 5
3
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
W3EG7232S-xAD4
-xBD4
White Electronic Designs
ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Value
– 0.5 ~ 3.6
–1.0 ~ 3.6
– 55 ~ +150
9
Units
V
Voltage on any pin relative to VSS
Voltage on VCC supply relative to VSS
Storage Temperature
VIN, VOUT
VCC, VCCQ
TSTG
V
°C
W
Power Dissipation
PD
Short Circuit Current
IOS
50
mA
Note:
Permanent device damage may occur if "ABSOLUTE MAXIMUM RATINGS" are exceeded.
Functional operation should be restricted to recommended operating condition.
Exposure to higher than recommended voltage for extended periods of time could affect device reliability.
DC CHARACTERISTICS
0°C ≤ TA ≤ 70°C, VCC = 2.5V ± 0.2V
Parameter
Symbol
VCC
Min
Max
2.7
Unit
V
Supply Voltage
2.3
2.3
Supply Voltage
VCCQ
VREF
VTT
2.7
V
Reference Voltage
Termination Voltage
Input High Voltage
Input Low Voltage
Output High Voltage
Output Low Voltage
1.15
1.35
V
1.15
1.35
V
VIH
VREF + 0.15
– 0.3
VCCQ + 0.3
VREF – 0.15
—
V
VIL
V
VOH
VTT + 0.76
—
V
VOL
VTT – 0.76
V
CAPACITANCE
TA = 25°C, f = 1MHz, VCC = 2.5V ± 0.2V
Parameter
Symbol
Max
29
29
29
5.5
29
8
Unit
pF
pF
pF
pF
pF
pF
pF
pF
pF
Input Capacitance (A0-A12)
CIN1
CIN2
CIN3
CIN4
CIN5
CIN6
CIN7
COUT
COUT
Input Capacitance (RAS#,CAS#,WE#)
Input Capacitance (CKE0,CKE1)
Input Capacitance (CK0,CK0#)
Input Capacitance (CS0#,CS1#)
Input Capacitance (DQM0-DQM8)
Input Capacitance (BA0-BA1)
29
8
Data input/output Capacitance (DQ0-DQ63)(DQS)
Data input/output Capacitance (CB0-CB7)
8
March 2007
Rev. 5
4
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
W3EG7232S-xAD4
-xBD4
White Electronic Designs
IDD SPECIFICATIONS AND TEST CONDITIONS
0°C TA 70°C, VCCQ = 2.5V ± 0.2V, VCC = 2.5V ± 0.2V
DDR333@
CL=2.5
DDR266@
CL=2, 2.5
DDR200@
CL=2
Parameter
Symbol Conditions
IDD0 One device bank; Active - Precharge; (MIN); DQ,DM and
Max
Max
Max
Units
Operating Current
1400
1400
1400
mA
DQS inputs changing once per clock cycle; Address and
control inputs changing once every two cycles. TRC=TRC(MIN);
TCK=TCK
Operating Current
IDD1
One device bank; Active-Read-Precharge; Burst = 2;
TRC=TRC(MIN);TCK=TCK (MIN); Iout = 0mA; Address and
control inputs changing once per clock cycle.
1805
1805
1715
mA
Precharge Power-Down IDD2P All device banks idle; Power-down mode; TCK=TCK(MIN);
36
36
36
mA
mA
Standby Current
CKE=(low)
Idle Standby Current
IDD2F CS# = High; All device banks idle; TCK=TCK(MIN); CKE = high;
Address and other control inputs changing once per clock
cycle. VIN = VREF for DQ, DQS and DM.
725
725
680
Active Power-Down
Standby Current
IDD3P One device bank active; Power-down mode; TCK(MIN);
CKE=(low)
270
815
270
815
225
725
mA
mA
Active Standby Current
IDD3N CS# = High; CKE = High; One device bank; Active-Precharge;
TRC=TRAS(MAX); TCK=TCK(MIN); DQ, DM and DQS inputs
changing twice per clock cycle; Address and other control
inputs changing once per clock cycle.
Operating Current
Operating Current
IDD4R Burst = 2; Reads; Continous burst; One device bank
active;Address andcontrol inputs changing once per clock
cycle; TCK=TCK(MIN); IOUT = 0mA.
1850
1850
1850
1850
1625
1625
mA
mA
IDD4W Burst = 2; Writes; Continous burst; One device bank active;
Address and control inputs changing once per clock cycle;
TCK=TCK(MIN); DQ,DM and DQS inputs changing twice per
clock cycle.
Auto Refresh Current
Self Refresh Current
Operating Current
IDD5
IDD6
TRC=TRC(MIN)
2570
311
2570
311
2390
311
mA
mA
mA
CKE ≤ 0.2V
IDD7A Four bank interleaving Reads (BL=4) with auto precharge with
TRC=TRC (MIN); TCK=TCK(MIN); Address and control inputs
change only during Active Read or Write commands
3965
3965
3425
March 2007
Rev. 5
5
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
W3EG7232S-xAD4
-xBD4
White Electronic Designs
DETAILED TEST CONDITIONS FOR DDR SDRAM IDD1 & IDD7A
IDD1 : OPERATING CURRENT : ONE BANK
IDD7A : OPERATING CURRENT : FOUR BANKS
1. Typical Case : VCC=2.5V, T=25°C
2. Worst Case : VCC=2.7V, T=10°C
1. Typical Case : VCC=2.5V, T=25°C
2. Worst Case : VCC=2.7V, T=10°C
3. Only one bank is accessed with tRC (min), Burst
Mode, Address and Control inputs on NOP edge
are changing once per clock cycle. IOUT = 0mA
3. Four banks are being interleaved with tRC (min),
Burst Mode, Address and Control inputs on NOP
edge are not changing. Iout=0mA
4. Timing Patterns :
4. Timing Patterns :
•
•
•
•
DDR200 (100 MHz, CL=2) : tCK=10ns, CL2,
BL=4, tRCD=2*tCK, tRAS=5*tCK
Read : A0 N R0 N N P0 N A0 N - repeat the
same timing with random address changing;
50% of data changing at every burst
•
DDR200 (100 MHz, CL=2) : tCK=10ns, CL2,
BL=4, tRRD=2*tCK, tRCD=3*tCK, Read with
Autoprecharge
Read : A0 N A1 R0 A2 R1 A3 R2 A0 R3 A1 R0
- repeat the same timing with random address
changing; 100% of data changing at every
burst
DDR266 (133MHz, CL=2.5) : tCK=7.5ns,
CL=2.5, BL=4, tRCD=3*tCK, tRC=9*tCK, tRAS=5*tCK
Read : A0 N N R0 N P0 N N N A0 N - repeat
the same timing with random address
•
DDR266 (133MHz, CL=2.5) : tCK=7.5ns,
CL=2.5, BL=4, tRRD=3*tCK, tRCD=3*tCK
Read with Autoprecharge
Read : A0 N A1 R0 A2 R1 A3 R2 N R3 A0 N
A1 R0 - repeat the same timing with random
address changing; 100% of data changing at
every burst
changing; 50% of data changing at every burst
DDR266 (133MHz, CL=2) : tCK=7.5ns, CL=2,
BL=4, tRCD=3*tCK, tRC=9*tCK, tRAS=5*tCK
Read : A0 N N R0 N P0 N N N A0 N - repeat
the same timing with random address
changing; 50% of data changing at every burst
•
•
DDR266 (133MHz, CL=2) : tCK=7.5ns, CL2=2,
BL=4, tRRD=2*tCK, tRCD=2*tCK
Read : A0 N A1 R0 A2 R1 A3 R2 N R3 A0 N
A1 R0 - repeat the same timing with random
address changing; 100% of data changing at
every burst
DDR333 (166MHz, CL=2.5) : tCK=6ns, BL=4,
tRCD=10*tCK, tRAS=7*tCK
Read : A0 N N R0 N P0 N N N A0 N - repeat
the same timing with random address
changing; 50% of data changing at every burst
DDR333 (166MHz, CL=2.5) : tCK=6ns,
BL=4, tRRD=3*tCK, tRCD=3*tCK, Read with
Autoprecharge
Read : A0 N A1 R0 A2 R1 A3 R2 N R3 A0 N
A1 R0 - repeat the same timing with random
address changing; 100% of data changing at
every burst
Legend : A = Activate, R = Read, W = Write, P = Precharge, N = NOP
A (0-3) = Activate Bank 0-3
R (0-3) = Read Bank 0-3
March 2007
Rev. 5
6
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
W3EG7232S-xAD4
-xBD4
White Electronic Designs
ELECTRICAL CHARACTERISTICS AND RECOMMENDED AC OPERATING CONDITIONS
AC CHARACTERISTICS
335
262
265
202
PARAMETER
SYMBOL MIN
MAX
+0.7
0.55
0.55
13
MIN
MAX
MIN
MAX
MIN
MAX UNITS NOTES
Access window of DQs from CK/CK#
CK high-level width
CK low-level width
tAC
-0.7
0.45
0.45
6
-0.75 +0.75 -0.75 +0.75 -0.75 +0.75
ns
tCK
tCK
ns
ns
ns
ns
ns
ns
tCK
tCK
ns
tCH
tCL
0.45
0.45
7.5
0.55
0.55
13
0.45
0.45
7.5
0.55
0.55
13
0.45
0.45
7.5
0.55
0.55
13
26
26
Clock cycle time
CL = 2.5 tCK (2.5)
39, 44
39, 44
23, 27
23, 27
27
CL = 2
tCK (2)
tDH
7.5
13
7.5
13
7.5
13
10
13
DQ and DM input hold time relative to DQS
DQ and DM input setup time relative to DQS
DQ and DM input pulse width (for each input)
Access window of DQS from CK/CK#
DQS input high pulse width
0.45
0.45
1.75
-0.6
0.35
0.35
0.5
0.5
0.5
tDS
0.5
0.5
0.5
tDIPW
tDQSCK
tDQSH
tDQSL
tDQSQ
1.75
1.75
1.75
+0.6
-0.75 +0.75 -0.75 +0.75 -0.75 +0.75
0.35
0.35
0.35
0.35
0.35
0.35
DQS input low pulse width
DQS-DQ skew, DQS to last DQ valid, per group, per
access
0.45
1.25
0.5
0.5
0.6
22, 23
Write command to first DQS latching transition
DQS falling edge to CK rising - setup time
DQS falling edge from CK rising - hold time
Half clock period
tDQSS
tDSS
tDSH
tHP
0.75
0.2
0.75
0.2
1.25
0.75
0.2
1.25
0.75
0.2
1.25
tCK
tCK
tCK
ns
ns
ns
ns
ns
ns
ns
0.2
0.2
0.2
0.2
tCH, tCL
+0.75
tCH, tCL
+0.75
30
16, 36
16, 36
12
Data-out high-impedance window from CK/CK#
Data-out low-impedance window from CK/CK#
Address and control input hold time (slow slew rate)
Address and control input setup time (slow slew rate)
Address and Control input pulse width (for each input)
LOAD MODE REGISTER command cycle time
tHZ
+0.7
+0.75
tLZ
-0.7
0.80
0.80
2.2
-0.75
0.90
0.90
2.2
-0.75
1
-0.75
1.1
1.1
2.2
15
tIH
S
tIS
1
12
S
tIPW
2.2
15
tMRD
12
15
March 2007
Rev. 5
7
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
W3EG7232S-xAD4
-xBD4
White Electronic Designs
ELECTRICAL CHARACTERISTICS AND RECOMMENDED AC OPERATING CONDITIONS (Continued)
AC CHARACTERISTICS
PARAMETER
335
262
265
202
SYMBOL MIN
MAX
MIN
tHP - tQHS
MAX
MIN
tHP - tQHS
MAX
MIN
tHP - tQHS
MAX UNITS NOTES
DQ-DQS hold, DQS to first DQ to go nonvalid, per
tQH
tHP - tQHS
ns
22, 23
access
Data Hold Skew Factor
tQHS
tRAS
tRAP
tRC
0.5
0.75
0.75
0.75
ns
ACTIVE to PRECHARGE command
ACTIVE to READ with Auto precharge command
42
15
60
70,000
40 120,000 40 120,000 40 120,000 ns
31, 47
15
60
15
60
20
65
ns
ns
ACTIVE to ACTIVE/AUTO REFRESH command
period
AUTO REFRESH command period
ACTIVE to READ or WRITE delay
PRECHARGE command period
DQS read preamble
tRFC
tRCD
72
15
15
0.9
0.4
12
0.25
0
75
15
15
0.9
0.4
15
0.25
0
75
15
15
0.9
0.4
15
0.25
0
75
20
20
0.9
0.4
15
0.25
0
ns
ns
ns
tCK
tCK
ns
tCK
ns
tCK
ns
tCK
ns
μs
μs
ns
ns
tCK
tRP
tRPRE
tRPST
tRRD
1.1
0.6
1.1
0.6
1.1
0.6
1.1
0.6
37
37
DQS read postamble
ACTIVE bank a to ACTIVE bank b command
DQS write preamble
tWPRE
tWPRES
tWPST
tWR
DQS write preamble setup time
DQS write postamble
18, 19
17
0.4
15
1
0.6
0.4
15
1
0.6
0.4
15
1
0.6
0.4
15
1
0.6
Write recovery time
Internal WRITE to READ command delay
Data valid output window (DVW)
REFRESH to REFRESH command interval
Average periodic refresh interval
Terminating voltage delay to VCC
Exit SELF REFRESH to non-READ command
Exit SELF REFRESH to READ command
tWTR
na
tQH - tDQSQ
tQH - tDQSQ
22
21
tREFC
tREFI
tVTD
70.3
7.8
70.3
7.8
70.3
7.8
70.3
7.8
0
0
0
0
0
tXSNR
tXSRD
75
75
75
75
200
200
200
200
March 2007
Rev. 5
8
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
W3EG7232S-xAD4
-xBD4
White Electronic Designs
Notes
1. All voltages referenced to VSS
2. Tests for AC timing, IDD, and electrical AC and DC characteristics may be
conducted at nominal reference/supply voltage levels, but the related specifications
and device operation are guaranteed for the full voltage range specified.
3. Outputs measured with equivalent load:
.
17. The intent of the Don’t Care state after completion of the postamble is the DQS-
driven signal should either be high, low, or high-Z and that any signal transition
within the input switching region must follow valid input requirements. That is, if
DQS transitions high [above VIHDC (MIN)] then it must not transition low (below
VIHDC) prior to tDQSH (MIN).
18. This is not a device limit. The device will operate with a negative value, but system
performance could be degraded due to bus turnaround.
V
TT
50Ω
19. It is recommended that DQS be valid (HIGH or LOW) on or before the WRITE
command. The case shown (DQS going from High-Z to logic LOW) applies when
no WRITEs were previously in progress on the bus. If a previous WRITE was in
RReeffeerreennccee
Output
Point
30pF
(VOUT
)
progress, DQS could be HIGH during this time, depending on tDQSS
.
20. MIN (tRC or tRFC) for IDD measurements is the smallest multiple of tCK that meets
the minimum absolute value for the respective parameter. tRAS (MAX) for IDD
measurements is the largest multiple of tCK that meets the maximum absolute value
4. AC timing and IDD tests may use a VIL-to-VIH swing of up to 1.5V in the test
environment, but input timing is still referenced to VREF (or to the crossing point for
CK/CK#), and parameter specifications are guaranteed for the specified AC input
levels under normal use conditions. The mini-mum slew rate for the input signals
used to test the device is 1V/ns in the range between VIL (AC) and VIH (AC).
5. The AC and DC input level specifications are as defined in the SSTL_2 Standard
(i.e., the receiver will effectively switch as a result of the signal crossing the AC
input level, and will remain in that state as long as the signal does not ring back
above [below] the DC input LOW [HIGH] level).
for tRAS
.
21. The refresh period 64ms. This equates to an average refresh rate of 7.8251μs.
However, an AUTO REFRESH command must be asserted at least once every
70.3μs; burst refreshing or posting by the DRAM controller greater than eight
refresh cycles is not allowed.
22. The valid data window is derived by achieving other specifications: tHP (tCK/2), tDQSQ
and tQH (tQH = tHP - tQHS). The data valid window derates in direct porportion with
the clock duty cycle and a practical data valid window can be derived, as shown in
Figure 7, Derating Data Valid Window. The clock is allowed a maximum duty cycle
variation of 45/55, beyond which functionality is uncertain. The data valid window
derating curves are provided below for duty cycles ranging between 50/50 and
45/55.
,
6.
VREF is expected to equal VCCQ/2 of the transmitting device and to track variations
in the DC level of the same. Peak-to-peak noise (non-common mode) on Vref may
not exceed ±2 percent of the DC value. Thus, from VCCQ/2, Vref is allowed ±25mV
for DC error and an additional ±25mV for AC noise. This measurement is to be
taken at the nearest VREF bypass capacitor.
23. Each byte lane has a corresponding DQS.
24. This limit is actually a nominal value and does not result in a fail value. CKE is
7.
8.
V
TT is not applied directly to the device. VTT is a system supply for signal
termination resistors, is expected to be set equal to VREF and must track variations
in the DC level of VREF
DD is dependent on output loading and cycle rates. Specified values are obtained
HIGH during REFRESH command period (tRFC [MIN]) else CKE is LOW (i.e., during
standby).
25. To maintain a valid level, the transitioning edge of the input must:
a. Sustain a constant slew rate from the current AC level through to the target AC
level, VIL (AC) or VIH (AC).
.
I
with mini-mum cycle time at CL = 2 for 262 and 202, CL = 2.5 for 335 and 265 with
the outputs open.
b. Reach at least the target AC level.
9. Enables on-chip refresh and address counters.
10. DD specifications are tested after the device is properly initialized, and is averaged
at the defined cycle rate.
11. This parameter is sampled. VCC = +2.5V ±0.2V, VCCQ = +2.5V ±0.2V, VREF = VSS
c. After the AC target level is reached, continue to maintain at least the target DC
level, VIL (DC) or VIH (DC).
26. JEDEC specifies CK and CK# input slew rate must be ≤ 1V/ns (2V/ns
differentially).
I
,
f = 100 MHz, TA = 25°C, VOUT(DC) = VCCQ/2, VOUT (peak to peak) = 0.2V. DM input
is grouped with I/O pins, reflecting the fact that they are matched in loading.
12. For slew rates < 1 V/ns and ≥ to 0.5 Vns. If the slew rate is < 0.5V/ns, timing must
be derated: tIS has an additional 50ps per each 100 mV/ns reduction in slew
rate from 500 mV/ns, while tIH is unaffected. If the slew rate exceeds 4.5 V/ns,
functionality is uncertain. For 335, slew rates must be 0.5 V/ns.
27. DQ and DM input slew rates must not deviate from DQS by more than 10 percent.
If the DQ/DM/DQS slew rate is less than 0.5 V/ns, timing must be derated: 50ps
must be added to tDS and tDH for each 100 mv/ns reduction in slew rate. If slew rate
exceeds 4 V/ns, functionality is uncertain. For 335, slew rates must be ≥ 0.5 V/ns.
28.
VCC must not vary more than 4 percent if CKE is not active while any bank is active.
29. The clock is allowed up to ±150ps of jitter. Each timing parameter is allowed to vary
by the same amount.
13. The CK/CK# input reference level (for timing referenced to CK/CK#) is the point at
which CK and CK# cross; the input reference level for signals other than CK/CK# is
30.
t
HP min is the lesser of tCL minimum and tCH minimum actually applied to the device
CK and CK# inputs, collectively during bank active.
31. READs and WRITEs with auto precharge are not allowed to be issued until
RAS(min) can be satisfied prior to the internal precharge command being issued.
VREF
.
14. Inputs are not recognized as valid until VREF stabilizes. Exception: during the period
before VREF stabilizes, CKE < 0.3 x VCCQ is recognized as LOW.
t
15. The output timing reference level, as measured at the timing reference point
32. Any positive glitch must be less than 1/3 of the clock and not more than +400mV or
2.9V, whichever is less. Any negative glitch must be less than 1/3 of the clock cycle
and not exceed either - 300mV or 2.2V, whichever is more positive.
indicated in Note 3, is VTT
.
16.
tHZ and tLZ transitions occur in the same access time windows as data valid
transitions. These parameters are not referenced to a specific voltage level, but
specify when the device output is no longer driving (HZ) or begins driving (LZ).
33. The voltage levels used are derived from a mini-mum VCC level and the referenced
test load. In practice, the voltage levels obtained from a properly terminated bus will
provide significantly different voltage values.
March 2007
Rev. 5
9
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
W3EG7232S-xAD4
-xBD4
White Electronic Designs
34. VIH overshoot: VIH(MAX) = VCCQ + 1.5V for a pulse width ≤ 3ns and the pulse width
can not be greater than 1/3 of the cycle rate. VIL undershoot: VIL (MIN) = -1.5V for a
pulse width ≤ 3ns and the pulse width can not be greater than 1/3 of the cycle rate.
42. Random addressing changing and 100 percent of data changing at every transfer.
43. CKE must be active (high) during the entire time a refresh command is executed.
That is, from the time the AUTO REFRESH command is registered, CKE must be
active at each rising clock edge, until tREF later.
35.
36.
V
t
CC and VCCQ must track each other.
HZ (MAX) will prevail over tDQSCK (MAX) + tRPST (MAX) condition. tLZ (MIN) will
prevail over tDQSCK (MIN) + tRPRE (MAX) condition.
RPST end point and tRPRE begin point are not referenced to a specific voltage level
44.
I
I
DD2N specifies the DQ, DQS, and DM to be driven to a valid high or low logic level.
DD2Q is similar to IDD2F except IDD2Q specifies the address and control inputs to
37.
t
remain stable. Although IDD2F, IDD2N, and IDD2Q are similar, IDD2F is “worst case.”
but specify when the device output is no longer driving (tRPST), or begins driving
(tRPRE).
45. Whenever the operating frequency is altered, not including jitter, the DLL is required
to be reset. This is followed by 200 clock cycles.
39. During initialization, VCCQ, VTT, and VREF must be equal to or less than VCC + 0.3V.
Alternatively, VTT may be 1.35V maximum during power up, even if VCC/VCCQ are
0Vs, provided a minimum of 42 0 of series resistance is used between the VTT
supply and the input pin.
46. Leakage number reflects the worst case leakage possible through the module pin,
not what each memory device contributes.
47. When an input signal is HIGH or LOW, it is defined as a steady state logic HIGH or
LOW.
40. The current part operates below the slowest JEDEC operating frequency of 83
MHz. As such, future die may not reflect this option.
48. The 335 speed grade will operate with tRAS (MIN) = 40ns and tRAS (MAX) =
120,000ns at any slower frequency.
41. Random addressing changing and 50 percent of data changing at every transfer.
March 2007
Rev. 5
10
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
W3EG7232S-xAD4
-xBD4
White Electronic Designs
ORDERING INFORMATION FOR BD4
Part Number
Speed
Height*
W3EG7232S335xBD4xxx
W3EG7232S262xBD4xxx
W3EG7232S265xBD4xxx
W3EG7232S202xBD4xxx
166MHz/333Mbps, CL=2.5
133MHz/266Mbps, CL=2
133MHz/266Mbps, CL=2.5
100MHz/200Mbps, CL=2
31.75 (1.25")
31.75 (1.25")
31.75 (1.25")
31.75 (1.25")
NOTES:
• Consult Factory for availability of RoHS compliant products. (G = RoHS Compliant)
• Vendor specific part numbers are used to provide memory components source control. The place holder for this is shown as lower
case “x” in the part numbers above and is to be replaced with the respective vendors code. Consult factory for qualified sourcing
options. (M = Micron, S = Samsung & consult factory for others)
• Consult factory for availability of industrial temperature (-40°C to 85°C) option
• For part numbering interpretation, please see "part numbering guide" on page 13
PACKAGE DIMENSIONS FOR BD4
3.81
(0.150) MAX.
67.56
(2.666) MAX
3.98 0.1
(0.157 0.004)
31.75
(1.25)
20
(0.787)
2.31
(0.091) REF.
3.98
(0.157) MIN.
4.19
(0.165)
47.40
(1.866)
1.0 0.1
(0.039 0.004)
1.80
(0.071)
11.40
(0.449)
* ALL DIMENSIONS ARE IN MILLIMETERS AND (INCHES)
March 2007
Rev. 5
11
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
W3EG7232S-xAD4
-xBD4
White Electronic Designs
ORDERING INFORMATION FOR AD4
Part Number
Speed
Height*
W3EG7232S335xAD4xxx
W3EG7232S262xAD4xxx
W3EG7232S265xAD4xxx
W3EG7232S202xAD4xxx
166MHz/333Mbps, CL=2
133MHz/266Mbps, CL=2
133MHz/266Mbps, CL=2.5
100MHz/200Mbps, CL=2
35.05 (1.38")
35.05 (1.38")
35.05 (1.38")
35.05 (1.38")
NOTES:
• Consult Factory for availability of RoHS compliant products. (G = RoHS Compliant)
• Vendor specific part numbers are used to provide memory components source control. The place holder for this is shown as lower
case “x” in the part numbers above and is to be replaced with the respective vendors code. Consult factory for qualified sourcing
options. (M = Micron, S = Samsung & consult factory for others)
• Consult factory for availability of industrial temperature (-40°C to 85°C) option
• For part numbering interpretation, please see "part numbering guide" on page 13
PACKAGE DIMENSIONS FOR AD4
67.56
(2.664 MAX.
3.81
(0 .1504 MAX.
2.0
(0.0794
3.98 0.1
(0.157 0.00ꢀ4
35.05
(1.384 MAX.
20
(0.7874
P1
2.31
(0.0914 REF.
3.98
(0.1574 MIN.
ꢀ.19
(0.1654
ꢀ7.ꢀ0
(1.8664
1.80
(0.0714
1.0 0.1
(0.039 0.00ꢀ4
11.ꢀ0
(0.ꢀꢀ94
* ALL DIMENSIONS ARE IN MILLIMETERS AND (INCHES)
March 2007
Rev. 5
12
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
W3EG7232S-xAD4
-xBD4
White Electronic Designs
PART NUMBERING GUIDE
W 3 E G 72 32 S xxx x AD4 x x G
WEDC
MEMORY
DDR
GOLD
BUS WIDTH
DENSITY
2.5V
SPEED (Mb/s)
VENDOR COMPONENT
DIE REV OPTION
(Samsung = H-Die)
PACKAGE SO-DIMM
INDUSTRIAL TEMP OPTION
(For commercial leave "blank"
for industrial add "I")
COMPONENT VENDOR NAME
(M = Micron)
(S = Samsung)
G = RoHS COMPLIANT
(Add "G" for RoHS, leave
"blank" for leaded)
March 2007
Rev. 5
13
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
W3EG7232S-xAD4
-xBD4
White Electronic Designs
Document Title
256MB – 32Mx72, DDR SDRAM Unbuffered ECC, w/PLL
Revision History
Rev #
History
Release Date Status
Rev 0
Rev 1
Rev 2
Rev 3
Initial Release
7-24-03
4-04
Advanced
Preliminary
Preliminary
Preliminary
1.1 Added "BD4" package height option
2.1 Added 333MHz Speed
10-22-04
1-05
3.1 Added lead-free and RoHS notes
3.2 Added source control notes
3.3 Added industrial temperature options
Rev 4
Rev 5
4.1 Removed "ED" to reduce the number of characters
4.2 Added part number matrix
8-05
3-07
Preliminary
Final
5.1 Updated part numbering guide
5.2 Added component die rev
5.3 Added industrial temp option to part numbering guide
5.4 Moved from preliminary to final
March 2007
Rev. 5
14
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
相关型号:
©2020 ICPDF网 联系我们和版权申明