LXMG1626-12-65 [MICROSEMI]
12V 10W Dual CCFL Programmable Inverter Module; 12V 10W双CCFL可编程逆变器模块型号: | LXMG1626-12-65 |
厂家: | Microsemi |
描述: | 12V 10W Dual CCFL Programmable Inverter Module |
文件: | 总6页 (文件大小:213K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PanelMatch™
LXMG1626-12-65
®
12V 10W Dual CCFL Programmable Inverter Module
TM
PRODUCTION DATA SHEET
KEY FEATURES
DESCRIPTION
The LXMG1626-12-65¹ is a 10W dual wide range typically (100:1+) dimming
Output Direct Drive™ CCFL (Cold Cathode application.
Externally Programmable
Maximum Output Current
Easy to Use Brightness Control
RangeMAX™ Wide Range
Dimming
Output Open & Short-Circuit
Protection and Automatic Strike-
Voltage Regulation and Timeout
Fixed Frequency Operation
Rated From -20 to 70°C
Fluorescent
Lamp)
Inverter
Module
The resultant “burst drive” that
specifically designed to be compatible with a energizes the lamp is designed specifically
variety of LCD panels the have both lamps to ensure that no premature lamp
on one side of the panel and use a single degradation occurs, while allowing
common lamp return wire.
significant power savings at lower dim
LXMG1626 modules provide the levels.
designer with a vastly superior display
The modules convert DC voltage from
UL60950 E175910
brightness range. This brightness range is the system battery or AC adapter directly to
RoHS Compliant
achievable with virtually any LCD display.
The modules are available with a required to ignite and operate CCFL lamps.
dimming input that permits brightness The modules design utilizes
control from either, a DC voltage source, Microsemi’s LX1691B backlight con-
a PWM signal or external Potentiometer. troller, which provides a number of cost
high frequency, high-voltage waves
APPLICATIONS
Dual Lamp LCD’s Requiring a
Shared Common Lamp Return
Mates to a Single JST BHR-04-VS-
1 Lamp Connector
Desktop Displays
Industrial Display Controls
The maximum output current is and performance advantages due to the
externally programmable (through the input controller’s high level of integration. A 5V
connector) over a range of 10 to 13mA in input supply version (LXMG1626-05-65) is
1mA steps. This allows the inverter to match also available.
the panel’s lamp current specifications, or it
can be used to purposely drive the lamps at a stable
lower or higher current to decrease or secondary-side strike-voltage regulation
increase nominal brightness. and both open/shorted lamp protection with
RangeMAX™ Digital Dimming Technique fault timeout.
provides flicker-free brightness control in any
Other benefits of this new topology are
fixed-frequency operation,
BENEFITS
Smooth, Flicker Free 1%-100%
Full-Range Brightness Control
Programmable Output Current
Allows Inverter to Mate With a
Wide Variety of LCD Panel’s
Specifications
Output Open Circuit Voltage
Regulation Minimizes Corona
Discharge For High Reliability
IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com
¹Protected By U.S. Patents: 5,923,129; 5,930,121; 6,198,234; Patents Pending
PRODUCT HIGHLIGHT
PWM
Signal
DC Voltage
Source
Potentiometer
Microsemi
W
UNIVERSAL DIMMING INPUT
"PWM", VDC, OR POTENTIOMETER
Lamp Current 10 to 13mA in 1mA Steps
PACKAGE ORDER INFO
INVERTER MATES DIRECTLY
TO PANEL CONNECTORS
JST BHR-04VS-1
PART NUMBER
OUTPUT CONNECTOR
LXMG1626-12-65
JST SM04(4.0)B-BHS-1-TB(LF)(SN) or Yeon Ho 20015WR-07A00
Copyright © 2005
Rev. 1.0a, 2006-11-16
Microsemi
Page 1
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
PanelMatch™
LXMG1626-12-65
®
12V 10W Dual CCFL Programmable Inverter Module
TM
PRODUCTION DATA SHEET
ABSOLUTE MAXIMUM RATINGS (NOTE 1)
Input Signal Voltage (VIN1).....................................................................................................................................-0.3V to 16V
Input Power....................................................................................................................................................................... 14W
Output Voltage, no load ............................................................................................................ Internally Limited to 1800VRMS
Output Current ............................................................................................................................7.5mARMS (Internally Limited)
Output Power .................................................................................................................................................................... 10W
Input Signal Voltage (
Input)..................................................................................................................... -0.3V to VIN1
SLEEP
Input Signal Voltage (BRITE) ...............................................................................................................................-0.3V to 5.5V
Ambient Operating Temperature, zero airflow.....................................................................................................-20°C to 70°C
Operating Relative Humidity, non-condensing ................................................................................................................ ≤90%
Storage Temperature Range...............................................................................................................................-40°C to 85°C
Note 1: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified
terminal.
RECOMMENDED OPERATING CONDITIONS (R.C.)
This module has been designed to operate over a wide range of input and output conditions. However, best efficiency and performance
will be obtained if the module is operated under the condition listed in the ‘R.C.’ column. Min. and Max. columns indicate values beyond
which the inverter, although operational, will not function optimally.
Recommended Operating Conditions
Parameter
Symbol
Units
Min
R.C.
Max
Input Supply Voltage Range (Fully Regulated
Lamp Current)
Input Supply Voltage Range (Functional)
Output Power
Linear BRITE Control Input Voltage Range
Lamp Operating Voltage
Lamp Current (Full Brightness)
Operating Ambient Temperature Range
10.8
10.2
12
13.2
VIN1
V
12
8
14.4
9
2.0
690
13
PO
VBRT_ADJ
VLAMP
IOLAMP
TA
W
V
VRMS
mARMS
°C
0.1
510
10
600
-20
70
ELECTRICAL CHARACTERISTICS
Unless otherwise specified, the following specifications apply over the recommended operating condition and ambient temperature of
25°C except where otherwise noted.
LXMG1626-12-65
Parameter
Symbol
Test Conditions
Units
Min
Typ
Max
OUTPUT PIN CHARACTERISTICS
`
VBRT_ADJ > 2.0VDC
,
> 2.0V, VIN1 = 12VDC
SLEEP
ISET1 = Ground, ISET2 = Ground
VBRT_ADJ > 2.0VDC
Full Bright Lamp Current (two lamps)
IL(MAX)
IL(MAX)
IL(MAX)
IL(MAX)
ILL%DEV
IL(MIN)
9
10
11
12
13
5
11
12
mARMS
mARMS
mARMS
mARMS
%
,
> 2.0V, VIN1 = 12VDC
> 2.0V, VIN1 = 12VDC
> 2.0V, VIN1 = 12VDC
> 2.0V, VIN1 = 12VDC
> 2.0V, VIN1 = 12VDC
SLEEP
ISET1 = Ground, ISET2 = Open
VBRT_ADJ > 2.0VDC
Full Bright Lamp Current (two lamps)
Full Bright Lamp Current (two lamps)
Full Bright Lamp Current (two lamps)
10
,
SLEEP
ISET1 = Open, ISET2 = Ground
VBRT_ADJ > 2.0VDC
10.8
11.6
13.2
14.4
,
SLEEP
ISET1 = Open, ISET2 = Open
BRT_ADJ > 2.0VDC
Output Current Lamp to Lamp
Deviation
V
,
SLEEP
ISET1 = Open, ISET2 = Open
VBRT_ADJ = 0VDC
,
SLEEP
Min. Average Lamp Current
1.4
mARMS
ISET1 = ISET2 = Ground; IMIN = IMAX * √ of % duty cycle
Lamp Start Voltage
Operating Frequency
Burst Frequency
VLS
fO
-20°C < TA < 70°C, VIN1 > 10.8VDC
1450
57.5
224
1600
60.5
236
VRMS
kHz
Hz
VBRT_ADJ = 2.0VDC
,
> 2.0V, VIN1 = 12V
63.5
248
SLEEP
fBURST
Output Burst Frequency
Copyright © 2005
Rev. 1.0a, 2006-11-16
Microsemi
Page 2
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
PanelMatch™
LXMG1626-12-65
®
12V 10W Dual CCFL Programmable Inverter Module
TM
PRODUCTION DATA SHEET
ELECTRICAL CHARACTERISTICS (CONTINUED)
Unless otherwise specified, the following specifications apply over the recommended operating condition and ambient temperature of
25°C except where otherwise noted.
LXMG1626-12-65
Parameter
Symbol
Test Conditions
Units
Min
Typ
Max
BRITE INPUT
`
VBRT_ADJ = 0VDC
VBRT_ADJ = 3VDC
-13
1
µADC
µADC
Input Current
IBRT
Minimum Input for Max. Lamp Current VBRT_ADJ IO(LAMP) = Maximum Lamp Current
Maximum Input for Min. Lamp Current VBRT_ADJ IO(LAMP) = Minimum Lamp Current
SLEEP INPUT
2.0
2.05
VDC
VDC
0
`
`
`
VSLEEP
VSLEEP
RUN Mode
2.1
VIN1
0.8
VDC
VDC
SLEEP Mode
-0.3
SET1,2 INPUT
SET1,2 Low Threshold
Input Current
VL
0.4
50
V
ISET
VSET ≤ 0.4V
-300
µA
POWER CHARACTERISTICS
Sleep Current
IIN(MIN)
IIN(RUN)
V
IN1 = 12VDC
,
,
< 0.8V
0.0
10
µADC
SLEEP
SLEEP
VIN1 = 12VDC
≥ 2.0V, ISET1 = Ground
Run Current
Efficiency
720
mADC
ISET2 = Open, VLAMP = 600VRMS
IN1 = 12VDC ≥ 2.0V, ISET1 = Ground
V
,
SLEEP
ISET2 = Open, VLAMP = 600VRMS
85
%
η
FUNCTIONAL PIN DESCRIPTION
CONN
PIN
DESCRIPTION
CN1 (Molex 53261-0871) Mates with 51021-0800 housing, 50079-8100 pins. Mates with LX9501G input cable assembly
CN1-1
VIN1
Main Input Power Supply (10.8V < VIN1 < 13.2V)
Power Supply Return
CN1-2
CN1-3
CN1-4
GND
CN1-5
ON/OFF Control. (0V <
< 0.8 = OFF,
>= 2.1V = ON
SLEEP
SLEEP
BRITE
SET1
SLEEP
CN1-6
CN1-7
CN1-8
Brightness Control (0V to 2.0VDC). 2.0VDC gives maximum lamp current.
SET1 MSB Connecting this pin to ground decreases the output current (see Table 1)
SET2 LSB Connecting this pin to ground decreases the output current (see Table 1)
SET2
CN2 for LXMG1626-12-65 (JST SM04(4.0)B-BHS-1-TB(LF)(SN) or Yeon Ho 20015WR-07A00 )
CN2-1
CN2-2
CN2-3
CN2-4
High voltage connection to high Side of lamp. Connect to lamp terminal with shortest lead length.
DO NOT connect to Ground.
VHI1
VHI2
NC
High voltage connection to high Side of lamp. Connect to lamp terminal with shortest lead length.
DO NOT connect to Ground.
No Connect
Connection to low side of lamp. Connect to lamp terminal with longer lead length.
DO NOT connect to Ground
VLO
Copyright © 2005
Rev. 1.0a, 2006-11-16
Microsemi
Page 3
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
PanelMatch™
LXMG1626-12-65
®
12V 10W Dual CCFL Programmable Inverter Module
TM
PRODUCTION DATA SHEET
TABLE 1
OUTPUT CURRENT SETTINGS
SET1
SET2
(Pin 8)
Open*
Ground
Open*
Nominal Output Current
(Pin 7)
Open*
Open*
Ground
Ground
13mA
12mA
11mA
10mA
Ground
* If driven by a logic signal it should be open collector or open drain only, not a voltage source.
PHYSICAL DIMENSIONS
L XMG1626 -12-6 5
UNPLATED MOUNTING HOLE 3MM ±.08
.
DIA
6MM HEAD CLEARANCE BOTH HOLES
133mm
5.24in.
119mm
4.69in.
CN1
W
CN2
21mm
0.827in.
25mm
0.984in.
W
4.0mm
0.157in.
16mm
0.630in.
GROUNDED MOUNTING HOLE
3MM ±.08
.
DIA
1.0mm
0.0394in.
7.5mm
0.295in.
Max
weight: 18g
PCB tolerances ± 0.5mm , 4-40 recommended mounting screws
All dimensions are in millimeters. Inches are for reference only.
SIMPLIFIED BLOCK DIAGRAM
+3V
215K
High Voltage
Transformer
Controller
Comparator
VHI2
VHI 1
VBRITE
+
VIN1
0 - 2VDC
10.0K
Ramp
Transformer
Driver
-
Ramp
Gen
+3V
OCSENSE
10K
SET1
SET2
One of two
+3V
OVSENSE
ISENSE
10K
VLO
Copyright © 2005
Rev. 1.0a, 2006-11-16
Microsemi
Page 4
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
PanelMatch™
LXMG1626-12-65
®
12V 10W Dual CCFL Programmable Inverter Module
TM
PRODUCTION DATA SHEET
TYPICAL APPLICATION
12V
VIN1
The brightness control may be a voltage output DAC or
other voltage source, a digital pot or 500K manual pot. The
inverter contains an internal 215K pull-up to 3V to bias the
pot. A 3.3V Logic Level PWM signal from a micro-
controller may also be used as shown in Figure 1A.
DAC or
Pot
BRITE
VHI1
VHI2
500K
If you need to turn the inverter ON/OFF remotely, connect
LXMG1626-12-65
to TTL logic signal to the
input.
SLEEP
Connect VHI1 and VHI2 to high voltage wires from the
lamps. Connect VLO to the low voltage wire lamp return
(wire with thinner insulation). Never connect VLO to
circuit ground as this will defeat lamp current regulation.
If both lamp wires have heavy high voltage insulation,
SLEEP
VLO
SET1
SET2
NC
GND
NC
connect the longest wire to VLO. This wire is typically
white.
Use the SET1 and SET2 (see Figure 2) inputs to select the
desired maximum output current. Using these two pins in
combination allows the inverter to match a wide variety of
panels from different manufactures. Generally the best
lamp lifetime correlates with driving the CCFL at the
manufactures nominal current setting. However the SET1
and SET2 inputs allow the user the flexibility to adjust the
current to the maximum allowable output current to
increase panel brightness at the expense of some reduced
lamp life.
Figure 1 – Brightness Control
(Output current set to maximum)
PWM Signal
from System
BRITE
P.W.
LXMG1626-12-65
Although the SET pins are designed such that just leaving
them open or grounding them is all that is needed to set the
output current, they can also be actively set. Using an open
collector or open drain logic signal will allow you to
reduce the lamp current for situations where greater dim
range is required, as an example in nighttime situations. In
conjunction with a light sensor or other timer the panel
could be set to higher brightness (maximum output
current) for daytime illumination and lower brightness
(minimum or typical output current) at nighttime. Since
the dim ratio is a factor of both the burst duty cycle and the
peak output current, using this technique the effective dim
ratio can be increased greater than the burst duty cycle
alone. Conversely, the SET inputs could be used to
overdrive the lamp temporarily to facilitate faster lamp
warm up at initial lamp turn on. Of course, any possible
degradation on lamp life from such practices is the users
responsibility since not all lamps are designed to be
overdriven.
5µs to 200µS
0 < P.W. < 100% of period
Figure 1A – PWM Brightness Control
12V
VHI1
VHI2
VIN1
BRITE
LXMG1626-12-65
SLEEP
SET1
VLO
SET2
GND
The inverter has a built in fault timeout function. If both
outputs are open (lamps disconnected or broken) or shorted
to ground the inverter will attempt to strike the lamp for
number of cycles. After about one to two seconds without
success the inverter will shutdown. In order to restart the
inverter it is necessary to toggle the SLEEP input or cycle
the VIN1 input supply
L
L
H
H
L
H
L
10mARMS
11mARMS
12mARMS
13mARMS
H
L=GND; H=Open
Figure 2 – Max Output Current
(SET1 and SET2 Inputs)
Copyright © 2005
Rev. 1.0a, 2006-11-16
Microsemi
Page 5
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
PanelMatch™
LXMG1626-12-65
®
12V 10W Dual CCFL Programmable Inverter Module
TM
PRODUCTION DATA SHEET
NOTES
PRODUCTION DATA – Information contained in this document is proprietary to
Microsemi and is current as of publication date. This document may not be modified in
any way without the express written consent of Microsemi. Product processing does not
necessarily include testing of all parameters. Microsemi reserves the right to change the
configuration and performance of the product and to discontinue product at any time.
Copyright © 2005
Rev. 1.0a, 2006-11-16
Microsemi
Integrated Products
Page 6
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
相关型号:
©2020 ICPDF网 联系我们和版权申明