MT47H64M16HW-25EAT [MICRON]
DDR2 SDRAM; DDR2 SDRAM型号: | MT47H64M16HW-25EAT |
厂家: | MICRON TECHNOLOGY |
描述: | DDR2 SDRAM |
文件: | 总131页 (文件大小:9265K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
1Gb: x4, x8, x16 DDR2 SDRAM
Features
DDR2 SDRAM
MT47H256M4 – 32 Meg x 4 x 8 banks
MT47H128M8 – 16 Meg x 8 x 8 banks
MT47H64M16 – 8 Meg x 16 x 8 banks
Options1
Marking
Features
Configuration
•
VDD = +1.8V ±0.1V, VDDQ = +1.8V ±0.1V
JEDEC-standard 1.8V I/O (SSTL_18-compatible)
Differential data strobe (DQS, DQS#) option
4n-bit prefetch architecture
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
256 Meg x 4 (32 Meg x 4 x 8 banks)
128 Meg x 8 (16 Meg x 8 x 8 banks)
64 Meg x 16 (8 Meg x 16 x 8 banks)
256M4
128M8
64M16
–
–
–
FBGA package (Pb-free) – x16
•
•
84-ball FBGA (8mm x 12.5mm)
Rev. G, H
FBGA package (Pb-free) – x4, x8
HR
HQ
–
Duplicate output strobe (RDQS) option for x8
DLL to align DQ and DQS transitions with CK
8 internal banks for concurrent operation
Programmable CAS latency (CL)
60-ball FBGA (8mm x 11.5mm)
Rev. G
–
Posted CAS additive latency (AL)
FBGA package (Pb-free) – x4, x8
•
•
WRITE latency = READ latency - 1 tCK
Selectable burst lengths (BL): 4 or 8
Adjustable data-output drive strength
64ms, 8192-cycle refresh
60-ball FBGA (8mm x 10mm) Rev. H
FBGA package (lead solder) – x16
CF
–
84-ball FBGA (8mm x 12.5mm)
Rev. G, H
HW
–
FBGA package (lead solder) – x4, x8
•
On-die termination (ODT)
60-ball FBGA (8mm x 11.5mm)
Rev. G
HV
JN
–
Industrial temperature (IT) option
RoHS-compliant
FBGA package (lead solder) – x4, x8
•
•
60-ball FBGA (8mm x 10mm) Rev. H
–
Supports JEDEC clock jitter specification
Timing – cycle time
1.875ns @ CL = 7 (DDR2-1066)
2.5ns @ CL = 5 (DDR2-800)
2.5ns @ CL = 6 (DDR2-800)
3.0ns @ CL = 4 (DDR2-667)
3.0ns @ CL = 5 (DDR2-667)
3.75ns @ CL = 4 (DDR2-533)
-187E
-25E
-25
-3E
-3
–
–
–
–
–
–
-37E
Self refresh
•
•
Standard
Low-power
Operating temperature
– Commercial (0°C ≤ TC ≤ 85°C)
– Industrial (–40°C ≤ TC ≤ 95°C;
–40°C ≤ TA ≤ 85°C)
None
L
–
–
None
IT
AT
:G/:H
– Automotive (–40°C ≤ TC , TA ≤ 105ºC)
Revision
•
1. Not all options listed can be combined to
define an offered product. Use the Part
Catalog Search on www.micron.com for
product offerings and availability.
Note:
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
1
© 2004 Micron Technology, Inc. All rights reserved.
Products and specifications discussed herein are subject to change by Micron without notice.
1Gb: x4, x8, x16 DDR2 SDRAM
Features
Table 1: Key Timing Parameters
Data Rate (MT/s)
Speed Grade
CL = 3
CL = 4
533
CL = 5
667
800
667
667
667
n/a
CL = 6
800
800
800
n/a
CL = 7
1066
n/a
tRC (ns)
54
-187E
-25E
-25
400
400
400
400
400
400
533
55
533
n/a
55
-3E
667
n/a
54
-3
533
n/a
n/a
55
-37E
533
n/a
n/a
55
Table 2: Addressing
Parameter
256 Meg x 4
128 Meg x 8
64 Meg x 16
Configuration
Refresh count
Row address
Bank address
Column address
32 Meg x 4 x 8 banks
8K
16 Meg x 8 x 8 banks
8K
8 Meg x 16 x 8 banks
8K
A[13:0] (16K)
BA[2:0] (8)
A[13:0] (16K)
BA[2:0] (8)
A[9:0] (1K)
A[12:0] (8K)
BA[2:0] (8)
A[9:0] (1K)
A[11, 9:0] (2K)
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
2
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Features
Figure 1: 1Gb DDR2 Part Numbers
Example Part Number: MT47H128M8HQ-37E
-
:
MT47H
Configuration
Package
Speed
Revision
:G/:H Revision
Low power
Configuration
256 Meg x 4
128 Meg x 8
64 Meg x 16
L
256M4
128M8
64M16
IT Industrial temperature
AT Automotive temperature
Speed Grade
t
t
t
t
t
t
Package
Pb-free
-187E
-25E
-25
CK = 1.875ns, CL = 7
CK = 2.5ns, CL = 5
CK = 2.5ns, CL = 6
CK = 3ns, CL = 4
CK = 3ns, CL = 5
CK = 3.75ns, CL = 4
84-ball 8mm x 12.5mm FBGA
60-ball 8mm x 11.5mm FBGA
60-ball 8mm x 10.0mm FBGA
Lead solder
HR
HQ
CF
-3E
-3
-37E
84-ball 8mm x 12.5mm FBGA
60-ball 8mm x 10mm FBGA
60-ball 8mm x 11.5mm FBGA
HW
JN
HV
1. Not all speeds and configurations are available in all packages.
Note:
FBGA Part Number System
Due to space limitations, FBGA-packaged components have an abbreviated part marking that is different from the
part number. For a quick conversion of an FBGA code, see the FBGA Part Marking Decoder on Micron’s Web site:
http://www.micron.com.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
3
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Contents
State Diagram .................................................................................................................................................. 9
Functional Description ................................................................................................................................... 10
Industrial Temperature .............................................................................................................................. 10
Automotive Temperature ........................................................................................................................... 11
General Notes ............................................................................................................................................ 11
Functional Block Diagrams ............................................................................................................................. 12
Ball Assignments and Descriptions ................................................................................................................. 15
Packaging ...................................................................................................................................................... 19
Package Dimensions .................................................................................................................................. 19
FBGA Package Capacitance ......................................................................................................................... 22
Electrical Specifications – Absolute Ratings ..................................................................................................... 23
Temperature and Thermal Impedance ........................................................................................................ 23
Electrical Specifications – IDD Parameters ........................................................................................................ 26
IDD Specifications and Conditions ............................................................................................................... 26
IDD7 Conditions .......................................................................................................................................... 27
AC Timing Operating Specifications ................................................................................................................ 31
AC and DC Operating Conditions .................................................................................................................... 41
ODT DC Electrical Characteristics ................................................................................................................... 42
Input Electrical Characteristics and Operating Conditions ............................................................................... 43
Output Electrical Characteristics and Operating Conditions ............................................................................. 46
Output Driver Characteristics ......................................................................................................................... 48
Power and Ground Clamp Characteristics ....................................................................................................... 52
AC Overshoot/Undershoot Specification ......................................................................................................... 53
Input Slew Rate Derating ................................................................................................................................ 55
Commands .................................................................................................................................................... 68
Truth Tables ............................................................................................................................................... 68
DESELECT ................................................................................................................................................. 72
NO OPERATION (NOP) .............................................................................................................................. 73
LOAD MODE (LM) ..................................................................................................................................... 73
ACTIVATE .................................................................................................................................................. 73
READ ......................................................................................................................................................... 73
WRITE ....................................................................................................................................................... 73
PRECHARGE .............................................................................................................................................. 74
REFRESH ................................................................................................................................................... 74
SELF REFRESH ........................................................................................................................................... 74
Mode Register (MR) ........................................................................................................................................ 74
Burst Length .............................................................................................................................................. 75
Burst Type ................................................................................................................................................. 76
Operating Mode ......................................................................................................................................... 76
DLL RESET ................................................................................................................................................. 76
Write Recovery ........................................................................................................................................... 77
Power-Down Mode .................................................................................................................................... 77
CAS Latency (CL) ........................................................................................................................................ 78
Extended Mode Register (EMR) ....................................................................................................................... 79
DLL Enable/Disable ................................................................................................................................... 80
Output Drive Strength ................................................................................................................................ 80
DQS# Enable/Disable ................................................................................................................................. 80
RDQS Enable/Disable ................................................................................................................................. 80
Output Enable/Disable ............................................................................................................................... 80
On-Die Termination (ODT) ........................................................................................................................ 81
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
4
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Off-Chip Driver (OCD) Impedance Calibration ............................................................................................ 81
Posted CAS Additive Latency (AL) ............................................................................................................... 81
Extended Mode Register 2 (EMR2) .................................................................................................................. 83
Extended Mode Register 3 (EMR3) .................................................................................................................. 84
Initialization .................................................................................................................................................. 85
ACTIVATE ...................................................................................................................................................... 88
READ ............................................................................................................................................................. 90
READ with Precharge ................................................................................................................................. 94
READ with Auto Precharge .......................................................................................................................... 96
WRITE .......................................................................................................................................................... 101
PRECHARGE ................................................................................................................................................. 111
REFRESH ...................................................................................................................................................... 112
SELF REFRESH .............................................................................................................................................. 113
Power-Down Mode ....................................................................................................................................... 115
Precharge Power-Down Clock Frequency Change .......................................................................................... 122
Reset ............................................................................................................................................................. 123
CKE Low Anytime ...................................................................................................................................... 123
ODT Timing .................................................................................................................................................. 125
MRS Command to ODT Update Delay ........................................................................................................ 127
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
5
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
List of Tables
Table 1: Key Timing Parameters ...................................................................................................................... 2
Table 2: Addressing ......................................................................................................................................... 2
Table 3: FBGA 84-Ball – x16 and 60-Ball – x4, x8 Descriptions .......................................................................... 17
Table 4: Input Capacitance ............................................................................................................................ 22
Table 5: Absolute Maximum DC Ratings ........................................................................................................ 23
Table 6: Temperature Limits .......................................................................................................................... 24
Table 7: Thermal Impedance ......................................................................................................................... 25
Table 8: General IDD Parameters .................................................................................................................... 26
Table 9: IDD7 Timing Patterns (8-Bank Interleave READ Operation) ................................................................. 27
Table 10: DDR2 IDD Specifications and Conditions (Die Revisions E, G, and H) ................................................ 28
Table 11: AC Operating Specifications and Conditions .................................................................................... 31
Table 12: Recommended DC Operating Conditions (SSTL_18) ........................................................................ 41
Table 13: ODT DC Electrical Characteristics ................................................................................................... 42
Table 14: Input DC Logic Levels ..................................................................................................................... 43
Table 15: Input AC Logic Levels ..................................................................................................................... 43
Table 16: Differential Input Logic Levels ........................................................................................................ 44
Table 17: Differential AC Output Parameters .................................................................................................. 46
Table 18: Output DC Current Drive ................................................................................................................ 46
Table 19: Output Characteristics .................................................................................................................... 47
Table 20: Full Strength Pull-Down Current (mA) ............................................................................................ 48
Table 21: Full Strength Pull-Up Current (mA) ................................................................................................. 49
Table 22: Reduced Strength Pull-Down Current (mA) ..................................................................................... 50
Table 23: Reduced Strength Pull-Up Current (mA) .......................................................................................... 51
Table 24: Input Clamp Characteristics ........................................................................................................... 52
Table 25: Address and Control Balls ............................................................................................................... 53
Table 26: Clock, Data, Strobe, and Mask Balls ................................................................................................. 53
Table 27: AC Input Test Conditions ................................................................................................................ 54
Table 28: DDR2-400/533 Setup and Hold Time Derating Values (tIS and tIH) ................................................... 56
Table 29: DDR2-667/800/1066 Setup and Hold Time Derating Values (tIS and tIH) .......................................... 57
Table 30: DDR2-400/533 tDS, tDH Derating Values with Differential Strobe ..................................................... 60
Table 31: DDR2-667/800/1066 tDS, tDH Derating Values with Differential Strobe ............................................ 61
Table 32: Single-Ended DQS Slew Rate Derating Values Using tDSb and tDHb .................................................. 62
Table 33: Single-Ended DQS Slew Rate Fully Derated (DQS, DQ at VREF) at DDR2-667 ..................................... 62
Table 34: Single-Ended DQS Slew Rate Fully Derated (DQS, DQ at VREF) at DDR2-533 ..................................... 63
Table 35: Single-Ended DQS Slew Rate Fully Derated (DQS, DQ at VREF) at DDR2-400 ..................................... 63
Table 36: Truth Table – DDR2 Commands ..................................................................................................... 68
Table 37: Truth Table – Current State Bank n – Command to Bank n ............................................................... 69
Table 38: Truth Table – Current State Bank n – Command to Bank m .............................................................. 71
Table 39: Minimum Delay with Auto Precharge Enabled ................................................................................. 72
Table 40: Burst Definition .............................................................................................................................. 76
Table 41: READ Using Concurrent Auto Precharge ......................................................................................... 96
Table 42: WRITE Using Concurrent Auto Precharge ....................................................................................... 102
Table 43: Truth Table – CKE ......................................................................................................................... 117
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
6
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
List of Figures
Figure 1: 1Gb DDR2 Part Numbers ................................................................................................................... 3
Figure 2: Simplified State Diagram ................................................................................................................... 9
Figure 3: 256 Meg x 4 Functional Block Diagram ............................................................................................. 12
Figure 4: 128 Meg x 8 Functional Block Diagram ............................................................................................. 13
Figure 5: 64 Meg x 16 Functional Block Diagram ............................................................................................. 14
Figure 6: 60-Ball FBGA – x4, x8 Ball Assignments (Top View) ........................................................................... 15
Figure 7: 84-Ball FBGA – x16 Ball Assignments (Top View) .............................................................................. 16
Figure 8: 84-Ball FBGA Package (8mm x 12.5mm) – x16 ................................................................................... 19
Figure 9: 60-Ball FBGA Package (8mm x 11.5mm) – x4, x8 ............................................................................... 20
Figure 10: 60-Ball FBGA (8mm x 10mm) – x4, x8 ............................................................................................. 21
Figure 11: Example Temperature Test Point Location ..................................................................................... 24
Figure 12: Single-Ended Input Signal Levels ................................................................................................... 43
Figure 13: Differential Input Signal Levels ...................................................................................................... 44
Figure 14: Differential Output Signal Levels .................................................................................................... 46
Figure 15: Output Slew Rate Load .................................................................................................................. 47
Figure 16: Full Strength Pull-Down Characteristics ......................................................................................... 48
Figure 17: Full Strength Pull-Up Characteristics ............................................................................................. 49
Figure 18: Reduced Strength Pull-Down Characteristics ................................................................................. 50
Figure 19: Reduced Strength Pull-Up Characteristics ...................................................................................... 51
Figure 20: Input Clamp Characteristics .......................................................................................................... 52
Figure 21: Overshoot ..................................................................................................................................... 53
Figure 22: Undershoot .................................................................................................................................. 53
Figure 23: Nominal Slew Rate for tIS .............................................................................................................. 58
Figure 24: Tangent Line for tIS ....................................................................................................................... 58
Figure 25: Nominal Slew Rate for tIH .............................................................................................................. 59
Figure 26: Tangent Line for tIH ...................................................................................................................... 59
Figure 27: Nominal Slew Rate for tDS ............................................................................................................. 64
Figure 28: Tangent Line for tDS ...................................................................................................................... 64
Figure 29: Nominal Slew Rate for tDH ............................................................................................................ 65
Figure 30: Tangent Line for tDH ..................................................................................................................... 65
Figure 31: AC Input Test Signal Waveform Command/Address Balls ............................................................... 66
Figure 32: AC Input Test Signal Waveform for Data with DQS, DQS# (Differential) ........................................... 66
Figure 33: AC Input Test Signal Waveform for Data with DQS (Single-Ended) .................................................. 67
Figure 34: AC Input Test Signal Waveform (Differential) ................................................................................. 67
Figure 35: MR Definition ............................................................................................................................... 75
Figure 36: CL ................................................................................................................................................ 78
Figure 37: EMR Definition ............................................................................................................................. 79
Figure 38: READ Latency ............................................................................................................................... 82
Figure 39: WRITE Latency ............................................................................................................................. 82
Figure 40: EMR2 Definition ........................................................................................................................... 83
Figure 41: EMR3 Definition ........................................................................................................................... 84
Figure 42: DDR2 Power-Up and Initialization ................................................................................................. 85
Figure 43: Example: Meeting tRRD (MIN) and tRCD (MIN) .............................................................................. 88
Figure 44: Multibank Activate Restriction ....................................................................................................... 89
Figure 45: READ Latency ............................................................................................................................... 91
Figure 46: Consecutive READ Bursts .............................................................................................................. 92
Figure 47: Nonconsecutive READ Bursts ........................................................................................................ 93
Figure 48: READ Interrupted by READ ........................................................................................................... 94
Figure 49: READ-to-WRITE ............................................................................................................................ 94
Figure 50: READ-to-PRECHARGE – BL = 4 ...................................................................................................... 95
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
7
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Figure 51: READ-to-PRECHARGE – BL = 8 ...................................................................................................... 95
Figure 52: Bank Read – Without Auto Precharge ............................................................................................. 97
Figure 53: Bank Read – with Auto Precharge ................................................................................................... 98
Figure 54: x4, x8 Data Output Timing – tDQSQ, tQH, and Data Valid Window .................................................. 99
Figure 55: x16 Data Output Timing – tDQSQ, tQH, and Data Valid Window ..................................................... 100
Figure 56: Data Output Timing – tAC and tDQSCK ......................................................................................... 101
Figure 57: Write Burst ................................................................................................................................... 103
Figure 58: Consecutive WRITE-to-WRITE ...................................................................................................... 104
Figure 59: Nonconsecutive WRITE-to-WRITE ................................................................................................ 104
Figure 60: WRITE Interrupted by WRITE ....................................................................................................... 105
Figure 61: WRITE-to-READ ........................................................................................................................... 106
Figure 62: WRITE-to-PRECHARGE ................................................................................................................ 107
Figure 63: Bank Write – Without Auto Precharge ............................................................................................ 108
Figure 64: Bank Write – with Auto Precharge ................................................................................................. 109
Figure 65: WRITE – DM Operation ................................................................................................................ 110
Figure 66: Data Input Timing ........................................................................................................................ 111
Figure 67: Refresh Mode ............................................................................................................................... 112
Figure 68: Self Refresh .................................................................................................................................. 114
Figure 69: Power-Down ................................................................................................................................ 116
Figure 70: READ-to-Power-Down or Self Refresh Entry .................................................................................. 118
Figure 71: READ with Auto Precharge-to-Power-Down or Self Refresh Entry .................................................. 118
Figure 72: WRITE-to-Power-Down or Self Refresh Entry ................................................................................ 119
Figure 73: WRITE with Auto Precharge-to-Power-Down or Self Refresh Entry ................................................. 119
Figure 74: REFRESH Command-to-Power-Down Entry ................................................................................. 120
Figure 75: ACTIVATE Command-to-Power-Down Entry ................................................................................ 120
Figure 76: PRECHARGE Command-to-Power-Down Entry ............................................................................ 121
Figure 77: LOAD MODE Command-to-Power-Down Entry ............................................................................ 121
Figure 78: Input Clock Frequency Change During Precharge Power-Down Mode ........................................... 122
Figure 79: RESET Function ........................................................................................................................... 124
Figure 80: ODT Timing for Entering and Exiting Power-Down Mode .............................................................. 126
Figure 81: Timing for MRS Command to ODT Update Delay .......................................................................... 127
Figure 82: ODT Timing for Active or Fast-Exit Power-Down Mode ................................................................. 127
Figure 83: ODT Timing for Slow-Exit or Precharge Power-Down Modes ......................................................... 128
Figure 84: ODT Turn-Off Timings When Entering Power-Down Mode ............................................................ 128
Figure 85: ODT Turn-On Timing When Entering Power-Down Mode ............................................................. 129
Figure 86: ODT Turn-Off Timing When Exiting Power-Down Mode ............................................................... 130
Figure 87: ODT Turn-On Timing When Exiting Power-Down Mode ................................................................ 131
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
8
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
State Diagram
State Diagram
Figure 2: Simplified State Diagram
CKE_L
Initialization
sequence
OCD
default
Self
refreshing
PRE
Idle
all banks
precharged
Setting
MRS
EMRS
(E)MRS
REFRESH
Refreshing
Precharge
power-
down
CKE_L
Automatic Sequence
Command Sequence
ACT
ACT = ACTIVATE
CKE_H = CKE HIGH, exit power-down or self refresh
CKE_L = CKE LOW, enter power-down
(E)MRS = (Extended) mode register set
PRE = PRECHARGE
CKE_L
Activating
PRE_A = PRECHARGE ALL
READ = READ
READ A = READ with auto precharge
REFRESH = REFRESH
Active
power-
down
SR = SELF REFRESH
WRITE = WRITE
WRITE A = WRITE with auto precharge
Bank
active
WRITE
READ
Writing
Reading
READ
WRITE
READ A
WRITE A
Writing
with
auto
Reading
with
auto
PRE, PRE_A
Precharging
precharge
precharge
1. This diagram provides the basic command flow. It is not comprehensive and does not
identify all timing requirements or possible command restrictions such as multibank in-
teraction, power down, entry/exit, etc.
Note:
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
9
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Functional Description
Functional Description
The DDR2 SDRAM uses a double data rate architecture to achieve high-speed opera-
tion. The double data rate architecture is essentially a 4n-prefetch architecture, with an
interface designed to transfer two data words per clock cycle at the I/O balls. A single
read or write access for the DDR2 SDRAM effectively consists of a single 4n-bit-wide, one-
clock-cycle data transfer at the internal DRAM core and four corresponding n-bit-wide,
one-half-clock-cycle data transfers at the I/O balls.
A bidirectional data strobe (DQS, DQS#) is transmitted externally, along with data, for
use in data capture at the receiver. DQS is a strobe transmitted by the DDR2 SDRAM
during READs and by the memory controller during WRITEs. DQS is edge-aligned with
data for READs and center-aligned with data for WRITEs. The x16 offering has two data
strobes, oneforthelowerbyte(LDQS, LDQS#)andonefortheupperbyte(UDQS, UDQS#).
The DDR2 SDRAM operates from a differential clock (CK and CK#); the crossing of CK
going HIGH and CK# going LOW will be referred to as the positive edge of CK. Com-
mands (address and control signals) are registered at every positive edge of CK. Input
data is registered on both edges of DQS, and output data is referenced to both edges of
DQS as well as to both edges of CK.
Read and write accesses to the DDR2 SDRAM are burst-oriented; accesses start at a se-
lected location and continue for a programmed number of locations in a programmed
sequence. Accesses begin with the registration of an ACTIVATE command, which is
then followed by a READ or WRITE command. The address bits registered coincident
with the ACTIVATE command are used to select the bank and row to be accessed. The
address bits registered coincident with the READ or WRITE command are used to select
the bank and the starting column location for the burst access.
The DDR2 SDRAM provides for programmable read or write burst lengths of four or
eight locations. DDR2 SDRAM supports interrupting a burst read of eight with another
read or a burst write of eight with another write. An auto precharge function may be
enabled to provide a self-timed row precharge that is initiated at the end of the burst
access.
As with standard DDR SDRAM, the pipelined, multibank architecture of DDR2 SDRAM
enables concurrent operation, thereby providing high, effective bandwidth by hiding
row precharge and activation time.
A self refresh mode is provided, along with a power-saving, power-down mode.
All inputs are compatible with the JEDEC standard for SSTL_18. All full drive-strength
outputs are SSTL_18-compatible.
Industrial Temperature
The industrial temperature (IT) option, if offered, has two simultaneous requirements:
ambient temperature surrounding the device cannot be less than –40°C or greater than
+85°C, and the case temperature cannot be less than –40°C or greater than +95°C. JE-
DEC specifications require the refresh rate to double when TC exceeds +85°C; this also
requires use of the high-temperature self refresh option. Additionally, ODT resistance
and the input/output impedance must be derated when TC is < 0°C or > +85°C.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
10
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Functional Description
Automotive Temperature
The automotive temperature (AT) option, if offered, has two simultaneous require-
ments: ambient temperature surrounding the device cannot be less than –40°C or
greater than +105°C, and the case temperature cannot be less than –40°C or greater
than +105°C. JEDEC specifications require the refresh rate to double when TC exceeds
+85°C; this also requires use of the high-temperature self refresh option. Additionally,
ODT resistance and the input/output impedance must be derated when TC is < 0°C or >
+85°C.
General Notes
The functionality and the timing specifications discussed in this data sheet are for the
DLL-enabled mode of operation.
•
•
Throughout the data sheet, the various figures and text refer to DQs as “DQ.” The DQ
term is to be interpreted as any and all DQ collectively, unless specifically stated oth-
erwise. Additionally, the x16 is divided into 2 bytes: the lower byte and the upper byte.
For the lower byte (DQ0–DQ7), DM refers to LDM and DQS refers to LDQS. For the
upper byte (DQ8–DQ15), DM refers to UDM and DQS refers to UDQS.
Complete functionality is described throughout the document, and any page or dia-
gram may have been simplified to convey a topic and may not be inclusive of all
requirements.
•
•
Any specific requirement takes precedence over a general statement.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
11
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Functional Block Diagrams
Functional Block Diagrams
The DDR2 SDRAM is a high-speed CMOS, dynamic random access memory. It is inter-
nally configured as a multibank DRAM.
Figure 3: 256 Meg x 4 Functional Block Diagram
ODT
Bank 7
Bank 6
CKE
CK
CK#
Bank 7
Bank 6
Control
logic
Bank 5
Bank 5
Bank 4
Bank 4
Bank 3
Bank 3
Bank 2
Bank 1
CS#
RAS#
CAS#
WE#
Bank 2
ODT control
Vdd Q
CK, CK#
DLL
Bank 1
Bank 0
sw1 sw2 sw3
COL0, COL1
MUX
Bank 0
14
row-
address
latch
4
4
4
4
Memory array
(16,384 x 512 x 16)
Refresh
counter
16,384
14
Mode
registers
sw1 sw2 sw3
Row-
address
MUX
4
16
and
decoder
Read
latch
DRVRS
R1
R1
R2
R2
R3
R3
DATA
17
DQ0–DQ3
DQS, DQS#
DM
14
Sense amplifiers
8,192
2
DQS
generator
DQS, DQS#
16
Input
registers
1
sw1 sw2 sw3
1
1
R1
R1
R2
R2
R3
R3
I/O gating
DM mask logic
1
1
1
4
4
4
4
2
A0–A13,
BA0–BA2
1
4
Address
register
Bank
WRITE
FIFO
and
17
1
control
logic
Mask
3
512
(x16)
1
RCVRS
16
drivers
4
4
4
4
sw1 sw2 sw3
Column
decoder
4
CK out
CK in
16
CK, CK#
R1
R1
R2
R2
R3
R3
Column-
address
counter/
latch
9
Data
11
2
2
COL0, COL1
Vss Q
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
12
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Functional Block Diagrams
Figure 4: 128 Meg x 8 Functional Block Diagram
ODT
Bank 7
Bank 6
CKE
CK
CK#
Bank 7
Bank 6
Control
logic
Bank 5
Bank 5
Bank 4
Bank 4
Bank 3
Bank 3
Bank 2
Bank 1
CS#
RAS#
CAS#
WE#
Bank 2
ODT control
Vdd Q
CK, CK#
DLL
Bank 1
Bank 0
COL0, COL1
MUX
sw1 sw2 sw3
Bank 0
14
row-
address
latch
8
8
8
8
Memory array
(16,384 x 256 x 32)
Refresh
counter
16,384
14
Mode
registers
sw1 sw2 sw3
Row-
address
MUX
8
32
and
decoder
Read
latch
DRVRS
R1
R1
R2
R2
R3
R3
Data
17
DQ0–DQ7
14
Sense amplifers
8,192
2
DQS
generator
UDQS, UDQS#
LDQS, LDQS#
32
Input
registers
2
sw1 sw2 sw3
2
2
R1
R1
R2
R2
R3
R3
I/O gating
DM mask logic
2
2
2
8
8
8
8
2
DQS, DQS#
RDQS#
A0–A13,
BA0–BA2
2
4
Address
register
Bank
control
logic
WRITE
FIFO
and
17
2
Mask
3
256
(x32)
2
RCVRS
32
drivers
8
sw1 sw2 sw3
Column
decoder
8
8
CK out
CK in
32
CK,CK#
RDQS
DM
R1
R1
R2
R2
R3
R3
Column-
address
counter/
latch
8
8
Data
10
2
8
2
COL0, COL1
Vss Q
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
13
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Functional Block Diagrams
Figure 5: 64 Meg x 16 Functional Block Diagram
ODT
Bank 7
Bank 6
CKE
CK
CK#
Bank 7
Bank 6
Control
logic
Bank 5
Bank 5
Bank 4
Bank 4
Bank 3
Bank 3
Bank 2
Bank 1
CS#
RAS#
CAS#
WE#
Bank 2
Bank 1
ODT control
sw1 sw2 sw3
Vdd Q
CK, CK#
DLL
Bank 0
COL0, COL1
16
Bank 0
13
row-
address
latch
Memory array
(8,192 x 256 x 64)
Refresh
counter
8,192
16
16
16
13
Mode
registers
sw1 sw2 sw3
Row-
address
MUX
16
64
and
decoder
Read
latch
DRVRS
R1
R1
R2
R2
R3
R3
MUX
DATA
16
DQ0–DQ15
13
Sense amplifier
16,384
4
DQS
generator
UDQS, UDQS#
LDQS, LDQS#
64
Input
registers
2
sw1 sw2 sw3
2
2
R1
R1
R2
R2
R3
R3
I/O gating
DM mask logic
2
2
UDQS, UDQS#
LDQS, LDQS#
A0–A12,
BA0–BA2
2
8
Address
register
Bank
WRITE
FIFO
and
16
2
2
control
logic
Mask
3
256
(x64)
2
2
RCVRS
64
drivers
16
16
16
16
16
16
16
16
sw1 sw2 sw3
Column
decoder
16
CK out
CK in
64
CK, CK#
R1
R1
R2
R2
R3
R3
Column-
address
counter/
latch
8
2
Data
10
UDM, LDM
4
COL0, COL1
Vss Q
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
14
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Ball Assignments and Descriptions
Ball Assignments and Descriptions
Figure 6: 60-Ball FBGA – x4, x8 Ball Assignments (Top View)
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
NC, RDQS#/NU
V
V
V
DQS#/NU V
DD
SS
SSQ
DDQ
V
NF, DQ6
DM, DM/RDQS
DQS
V
NF, DQ7
SSQ
SSQ
DQ1
V
V
V
DQ0
V
DDQ
DDQ
DDQ
DDQ
V
NF, DQ4
DQ3
DQ2
V
NF, DQ5
SSQ
SSQ
V
V
V
V
CK
V
REF
DDL
SS
SSDL
DD
CKE
BA0
A10
A3
WE#
BA1
A1
RAS# CK#
CAS# CS#
ODT
G
H
J
BA2
A2
A6
A0
A4
V
DD
V
A5
SS
K
L
A7
A9
A11
RFU
A8
V
SS
A12
V
RFU
A13
DD
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
15
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Ball Assignments and Descriptions
Figure 7: 84-Ball FBGA – x16 Ball Assignments (Top View)
1
2
3
4
5
6
7
8
9
A
B
C
D
E
VDD
DQ14
VDDQ
DQ12
VDD
NC
VSS
VSSQ UDQS#/NU VDDQ
VSSQ
DQ9
UDM
VDDQ
UDQS
VDDQ
DQ10
VSSQ
DQ8
VSSQ
DQ15
VDDQ
DQ13
VSSQ DQ11
NC
VSSQ
DQ1
VSSQ
VREF
CKE
BA0
A10
A3
VSS
LDM
VDDQ
DQ3
VSS
VSSQ LDQS#/NU VDDQ
F
DQ6
LDQS
VDDQ
DQ2
VSSDL
RAS#
CAS#
A2
VSSQ
DQ0
VSSQ
CK
DQ7
VDDQ
DQ5
VDD
G
H
J
VDDQ
DQ4
VDDL
K
L
WE#
BA1
A1
CK#
CS#
A0
ODT
BA2
VSS
M
N
P
VDD
A5
A6
A4
A7
A9
A11
A8
VSS
R
VDD
A12
RFU
RFU
RFU
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
16
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Ball Assignments and Descriptions
Table 3: FBGA 84-Ball – x16 and 60-Ball – x4, x8 Descriptions
Symbol
Type
Description
A[12:0] (x16)
,A[13:0] (x4, x8)
Input
Address inputs: Provide the row address for ACTIVATE commands, and the column ad-
dress and auto precharge bit (A10) for READ/WRITE commands, to select one location out
of the memory array in the respective bank. A10 sampled during a PRECHARGE com-
mand determines whether the PRECHARGE applies to one bank (A10 LOW, bank selected
by BA[2:0] or all banks (A10 HIGH). The address inputs also provide the op-code during a
LOAD MODE command.
BA[2:0]
CK, CK#
CKE
Input
Input
Input
Bank address inputs: BA[2:0] define to which bank an ACTIVATE, READ, WRITE, or PRE-
CHARGE command is being applied. BA[2:0] define which mode register, including MR,
EMR, EMR(2), and EMR(3), is loaded during the LOAD MODE command.
Clock: CK and CK# are differential clock inputs. All address and control input signals are
sampled on the crossing of the positive edge of CK and negative edge of CK#. Output
data (DQ and DQS/DQS#) is referenced to the crossings of CK and CK#.
Clock enable: CKE (registered HIGH) activates and CKE (registered LOW) deactivates
clocking circuitry on the DDR2 SDRAM. The specific circuitry that is enabled/disabled is
dependent on the DDR2 SDRAM configuration and operating mode. CKE LOW provides
precharge power-down and SELF REFRESH operations (all banks idle), or ACTIVATE power-
down (row active in any bank). CKE is synchronous for power-down entry, power-down
exit, output disable, and for self refresh entry. CKE is asynchronous for self refresh exit.
Input buffers (excluding CK, CK#, CKE, and ODT) are disabled during power-down. Input
buffers (excluding CKE) are disabled during self refresh. CKE is an SSTL_18 input but will
detect a LVCMOS LOW level after VDD is applied during first power-up. After VREF has
become stable during the power-on and initialization sequence, it must be maintained
for proper operation of the CKE receiver. For proper SELF REFRESH operation, VREF must
be maintained.
CS#
Input
Input
Chip select: CS# enables (registered LOW) and disables (registered HIGH) the command
decoder. All commands are masked when CS# is registered high. CS# provides for exter-
nal bank selection on systems with multiple ranks. CS# is considered part of the com-
mand code.
LDM, UDM, DM
Input data mask: DM is an input mask signal for write data. Input data is masked when
DM is sampled HIGH along with that input data during a WRITE access. DM is sampled on
both edges of DQS. Although DM balls are input-only, the DM loading is designed to
match that of DQ and DQS balls. LDM is DM for lower byte DQ[7:0] and UDM is DM for
upper byte DQ[15:8].
ODT
Input
On-die termination: ODT (registered HIGH) enables termination resistance internal to
the DDR2 SDRAM. When enabled, ODT is only applied to each of the following balls:
DQ[15:0], LDM, UDM, LDQS, LDQS#, UDQS, and UDQS# for the x16; DQ[7:0], DQS, DQS#,
RDQS, RDQS#, and DM for the x8; DQ[3:0], DQS, DQS#, and DM for the x4. The ODT input
will be ignored if disabled via the LOAD MODE command.
RAS#, CAS#, WE#
Input
I/O
Command inputs: RAS#, CAS#, and WE# (along with CS#) define the command being
entered.
DQ[15:0] (x16)
DQ[3:0] (x4)
DQ[7:0] (x8)
Data input/output: Bidirectional data bus for 64 Meg x 16.
Bidirectional data bus for 256 Meg x 4.
Bidirectional data bus for 128 Meg x 8.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
17
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Ball Assignments and Descriptions
Table 3: FBGA 84-Ball – x16 and 60-Ball – x4, x8 Descriptions (Continued)
Symbol
Type
Description
DQS, DQS#
I/O
Data strobe: Output with read data, input with write data for source synchronous oper-
ation. Edge-aligned with read data, center-aligned with write data. DQS# is only used
when differential data strobe mode is enabled via the LOAD MODE command.
LDQS, LDQS#
UDQS, UDQS#
RDQS, RDQS#
I/O
I/O
Data strobe for lower byte: Output with read data, input with write data for source
synchronous operation. Edge-aligned with read data, center-aligned with write data.
LDQS# is only used when differential data strobe mode is enabled via the LOAD MODE
command.
Data strobe for upper byte: Output with read data, input with write data for source
synchronous operation. Edge-aligned with read data, center-aligned with write data.
UDQS# is only used when differential data strobe mode is enabled via the LOAD MODE
command.
Output
Redundant data strobe: For x8 only. RDQS is enabled/disabled via the LOAD MODE com-
mand to the extended mode register (EMR). When RDQS is enabled, RDQS is output with
read data only and is ignored during write data. When RDQS is disabled, ball B3 becomes
data mask (see DM ball). RDQS# is only used when RDQS is enabled and differential data
strobe mode is enabled.
VDD
VDDQ
VDDL
VREF
VSS
Supply
Supply
Supply
Supply
Supply
Supply
Supply
–
Power supply: 1.8V ±0.1V.
DQ power supply: 1.8V ±0.1V. Isolated on the device for improved noise immunity.
DLL power supply: 1.8V ±0.1V.
SSTL_18 reference voltage (VDDQ/2).
Ground.
VSSDL
VSSQ
NC
DLL ground: Isolated on the device from VSS and VSSQ.
DQ ground: Isolated on the device for improved noise immunity.
No connect: These balls should be left unconnected.
NF
No function: x8: these balls are used as DQ[7:4]; x4: they are no function.
–
NU
Not used: For x16 only. If EMR(E10) = 0, A8 and E8 are UDQS# and LDQS#. If EMR(E10) =
–
1, then A8 and E8 are not used.
NU
Not used: For x8 only. If EMR(E10) = 0, A2 and E8 are RDQS# and DQS#. If EMR(E10) = 1,
then A2 and E8 are not used.
–
–
RFU
Reserved for future use: Row address bits A13 (x16 only), A14, and A15.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
18
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Packaging
Packaging
Package Dimensions
Figure 8: 84-Ball FBGA Package (8mm x 12.5mm) – x16
0.8 ±0.1
Seating
plane
A
0.12 A
84X Ø0.45
Solder ball material:
Pb-free – (SAC305) SnAgCu
Pb – (Eutectic) SnPbAg
8 ±0.1
0.25 MIN
Ball A1 ID
Dimensions apply to
solder balls post-reflow
on Ø0.35 SMD ball pads.
Ball A1 ID
9
8
7
3
2
1
A
B
C
D
E
F
G
H
J
11.2 CTR
12.5 ±0.1
0.8 TYP
K
L
M
N
P
R
Exposed
gold-plated pad
1.2 MAX
0.8 TYP
1.0 MAX X 0.7 NOM
nonconductive floating pad
6.4 CTR
1. All dimensions are in millimeters.
Note:
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
19
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Packaging
Figure 9: 60-Ball FBGA Package (8mm x 11.5mm) – x4, x8
0.8 ±0.1
Seating
plane
A
0.12 A
60X Ø0.45
Solder ball material:
Pb-free – (SAC305) SnAgCu
Ball A1 ID
Pb – (Eutectic) SnPbAg
Dimensions apply to solder
balls post-reflow on
Ball A1 ID
9
8
7
3
2
1
Ø0.35 SMD ball pads.
A
B
C
D
E
F
11.5 ±0.1
8 CTR
G
H
J
K
L
0.8 TYP
0.8 TYP
Exposed
gold-plated pad
1.0 MAX X 0.7
nonconductive
floating pad
1.2 MAX
0.25 MIN
6.4 CTR
8 ±0.1
1. All dimensions are in millimeters.
Note:
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
20
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Packaging
Figure 10: 60-Ball FBGA (8mm x 10mm) – x4, x8
0.8 ±0.1
Seating
Plane
A
0.12 A
60X Ø0.45
Solder ball material:
Pb-free – (SAC305) SnAgCu
Pb – (Eutectic) SnPbAg
Dimensions apply to
solder balls post-reflow
on Ø0.35 SMD ball pads.
Ball A1 ID
Ball A1 ID
9
8
7
3
2 1
A
B
C
D
E
F
8 CTR
10 ±0.15
G
H
J
K
L
0.8 TYP
0.8 TYP
1.2 MAX
0.25 MIN
1.0 X 0.73 MAX
exposed
6.4 CTR
gold-plated pad
nonconductive floating pad
8 ±0.15
1. All dimensions are in millimeters.
Note:
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
21
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Packaging
FBGA Package Capacitance
Table 4: Input Capacitance
Parameter
Symbol Min Max Units Notes
Input capacitance: CK, CK#
CCK
CDCK
CI
1.0 2.0
0.25 pF
1.0 2.0 pF
0.25 pF
pF
1
Delta input capacitance: CK, CK#
2, 3
1, 4
2, 3
–
Input capacitance: Address balls, bank address balls, CS#, RAS#, CAS#, WE#, CKE, ODT
Delta input capacitance: Address balls, bank address balls, CS#, RAS#, CAS#, WE#, CKE,
ODT
CDI
–
Input/output capacitance: DQ, DQS, DM, NF
CIO
2.5 4.0
0.5
pF
pF
1, 5
2, 3
Delta input/output capacitance: DQ, DQS, DM, NF
CDIO
–
1. This parameter is sampled. VDD = +1.8V ±0.1V, VDDQ = +1.8V ±0.1V, VREF = VSS, f = 100
MHz, TC = 25°C, VOUT(DC) = VDDQ/2, VOUT (peak-to-peak) = 0.1V. DM input is grouped
with I/O balls, reflecting the fact that they are matched in loading.
Notes:
2. The capacitance per ball group will not differ by more than this maximum amount for
any given device.
3.
ΔC are not pass/fail parameters; they are targets.
4. Reduce MAX limit by 0.25pF for -25, -25E, and -187E speed devices.
5. Reduce MAX limit by 0.5pF for -3, -3E, -25, -25E, and -187E speed devices.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2004 Micron Technology, Inc. All rights reserved.
22
1Gb: x4, x8, x16 DDR2 SDRAM
Electrical Specifications – Absolute Ratings
Electrical Specifications – Absolute Ratings
Stresses greater than those listed may cause permanent damage to the device. This is a
stress rating only, and functional operation of the device at these or any other condi-
tions outside those indicated in the operational sections of this specification is not
implied. Exposure to absolute maximum rating conditions for extended periods may
affect reliability.
Table 5: Absolute Maximum DC Ratings
Parameter
Symbol
VDD
Min
–1.0
–0.5
–0.5
–0.5
–5
Max
2.3
2.3
2.3
2.3
5
Units
Notes
VDD supply voltage relative to VSS
VDDQ supply voltage relative to VSSQ
VDDL supply voltage relative to VSSL
Voltage on any ball relative to VSS
V
V
1
1, 2
1
VDDQ
VDDL
V
VIN, VOUT
II
V
3
µA
Input leakage current; any input 0V ≤ VIN ≤ VDD; all other
balls not under test = 0V
IOZ
–5
5
µA
Output leakage current; 0V ≤ VOUT ≤ VDDQ; DQ and ODT dis-
abled
VREF leakage current; VREF = Valid VREF level
IVREF
–2
2
µA
1. VDD, VDDQ, and VDDL must be within 300mV of each other at all times; this is not re-
quired when power is ramping down.
Notes:
2.
VREF ≤ 0.6 × VDDQ; however, VREF may be ≥ VDDQ provided that VREF ≤ 300mV.
3. Voltage on any I/O may not exceed voltage on VDDQ
.
Temperature and Thermal Impedance
It is imperative that the DDR2 SDRAM device’s temperature specifications, shown in
Table 6 (page 24), be maintained in order to ensure the junction temperature is in the
proper operating range to meet data sheet specifications. An important step in maintain-
ing the proper junction temperature is using the device’s thermal impedances correct-
ly. The thermal impedances are listed in Table 7 (page 25) for the applicable and
available die revision and packages.
Incorrectly using thermal impedances can produce significant errors. Read Micron tech-
nical note TN-00-08, “Thermal Applications” prior to using the thermal impedances
listed in Table 7. For designs that are expected to last several years and require the flexi-
bility to use several DRAM die shrinks, consider using final target theta values (rather
than existing values) to account for increased thermal impedances from the die size re-
duction.
The DDR2 SDRAM device’s safe junction temperature range can be maintained when
the TC specification is not exceeded. In applications where the device’s ambient temper-
ature is too high, use of forced air and/or heat sinks may be required in order to satisfy
the case temperature specifications.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
23
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Electrical Specifications – Absolute Ratings
Table 6: Temperature Limits
Parameter
Symbol
TSTG
TC
Min
–55
0
Max
150
85
Units
°C
Notes
1
Storage temperature
Operating temperature: commercial
Operating temperature: industrial
°C
2, 3
TC
–40
–40
95
°C
2, 3, 4
4, 5
TA
85
°C
1. MAX storage case temperature TSTG is measured in the center of the package, as shown
in Figure 11. This case temperature limit is allowed to be exceeded briefly during pack-
age reflow, as noted in Micron technical note TN-00-15, “Recommended Soldering
Parameters.”
Notes:
2. MAX operating case temperature TC is measured in the center of the package, as shown
in Figure 11.
3. Device functionality is not guaranteed if the device exceeds maximum TC during opera-
tion.
4. Both temperature specifications must be satisfied.
5. Operating ambient temperature surrounding the package.
Figure 11: Example Temperature Test Point Location
Test point
Length (L)
0.5 (L)
0.5 (W)
Width (W)
Lmm x Wmm FBGA
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
24
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Electrical Specifications – Absolute Ratings
Table 7: Thermal Impedance
Substrate
θ JA (°C/W)
θ JA (°C/W)
θ JA (°C/W)
Die Revision Package
(pcb)
2-layer
4-layer
2-layer
4-layer
2-layer
4-layer
2-layer
4-layer
Airflow = 0m/s Airflow = 1m/s Airflow = 2m/s θ JB (°C/W) θ JC (°C/W)
G1
60-ball
84-ball
60-ball
84-ball
66.5
49.2
60.2
44
49.6
40.4
44.5
35.7
55.5
45.7
52.0
42.7
43.1
36.4
39.3
32.8
49.5
42.3
46.5
39.6
30.3
30
5.9
5.6
5.7
5.6
26.1
26.1
35.6
35.2
32.5
32.3
H1
72.5
54.5
68.8
51.3
1. Thermal resistance data is based on a number of samples from multiple lots and should
be viewed as a typical number.
Note:
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
25
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Electrical Specifications – IDD Parameters
Electrical Specifications – IDD Parameters
IDD Specifications and Conditions
Table 8: General IDD Parameters
IDD Parameters
CL (IDD
tRCD (IDD
tRC (IDD
tRRD (IDD) - x4/x8 (1KB)
tRRD (IDD) - x16 (2KB)
-187E
7
-25E
5
-25
6
-3E
4
-3
5
-37E
4
-5E
3
Units
tCK
ns
)
)
13.125
58.125
7.5
12.5
57.5
7.5
15
12
15
15
15
)
60
57
60
60
55
ns
7.5
10
7.5
10
7.5
10
7.5
7.5
10
ns
10
10
10
ns
tCK (IDD
tRAS MIN (IDD
tRAS MAX (IDD
tRP (IDD
tRFC (IDD - 256Mb)
tRFC (IDD - 512Mb)
tRFC (IDD - 1Gb)
)
1.875
45
2.5
2.5
45
3
3
3.75
45
5
ns
)
45
45
45
40
ns
)
70,000
13.125
75
70,000
12.5
75
70,000
15
70,000
12
70,000
15
70,000
15
70,000
15
ns
)
ns
75
75
75
75
75
ns
105
105
127.5
195
105
127.5
195
105
127.5
195
105
127.5
195
105
127.5
195
105
127.5
195
ns
127.5
195
ns
tRFC (IDD - 2Gb)
ns
tFAW (IDD) - x4/x8 (1KB)
tFAW (IDD) - x16 (2KB)
Defined by pattern in Table 9 (page 27)
Defined by pattern in Table 9 (page 27)
ns
ns
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
26
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Electrical Specifications – IDD Parameters
IDD7 Conditions
The detailed timings are shown below for IDD7. Where general IDD parameters in
Table 8 (page 26) conflict with pattern requirements of Table 9, then Table 9 require-
ments take precedence.
Table 9: IDD7 Timing Patterns (8-Bank Interleave READ Operation)
Speed
Grade IDD7 Timing Patterns
Timing patterns for 8-bank x4/x8 devices
-5E
-37E
-3
A0 RA0 A1 RA1 A2 RA2 A3 RA3 A4 RA4 A5 RA5 A6 RA6 A7 RA7
A0 RA0 A1 RA1 A2 RA2 A3 RA3 D D A4 RA4 A5 RA5 A6 RA6 A7 RA7 D D
A0 RA0 D A1 RA1 D A2 RA2 D A3 RA3 D D A4 RA4 D A5 RA5 D A6 RA6 D A7 RA7 D D
A0 RA0 D A1 RA1 D A2 RA2 D A3 RA3 D D A4 RA4 D A5 RA5 D A6 RA6 D A7 RA7 D D
A0 RA0 D A1 RA1 D A2 RA2 D A3 RA3 D D D A4 RA4 D A5 RA5 D A6 RA6 D A7 RA7 D D D
A0 RA0 D A1 RA1 D A2 RA2 D A3 RA3 D D D A4 RA4 D A5 RA5 D A6 RA6 D A7 RA7 D D D
A0 RA0 D D A1 RA1 D D A2 RA2 D D A3 RA3 D D D D D A4 RA4 D D A5 RA5 D D A6 RA6 D D A7 RA7 D D D D D
-3E
-25
-25E
-187E
Timing patterns for 8-bank x16 devices
-5E
-37E
-3
A0 RA0 A1 RA1 A2 RA2 A3 RA3 D D A4 RA4 A5 RA5 A6 RA6 A7 RA7 D D
A0 RA0 D A1 RA1 D A2 RA2 D A3 RA3 D D D A4 RA4 D A5 RA5 D A6 RA6 D A7 RA7 D D D
A0 RA0 D D A1 RA1 D D A2 RA2 D D A3 RA3 D D D A4 RA4 D D A5 RA5 D D A6 RA6 D D A7 RA7 D D D
A0 RA0 D D A1 RA1 D D A2 RA2 D D A3 RA3 D D D A4 RA4 D D A5 RA5 D D A6 RA6 D D A7 RA7 D D D
A0 RA0 D D A1 RA1 D D A2 RA2 D D A3 RA3 D D D D A4 RA4 D D A5 RA5 D D A6 RA6 D D A7 RA7 D D D D
A0 RA0 D D A1 RA1 D D A2 RA2 D D A3 RA3 D D D D A4 RA4 D D A5 RA5 D D A6 RA6 D D A7 RA7 D D D D
-3E
-25
-25E
-187E
A0 RA0 D D D D A1 RA1 D D D D A2 RA2 D D D D A3 RA3 D D D D A4 RA4 D D D D A5 RA5 D D D D A6 RA6 D
D D D A7 RA7 D D D D
1. A = active; RA = read auto precharge; D = deselect.
Notes:
2. All banks are being interleaved at tRC (IDD) without violating tRRD (IDD) using a BL = 4.
3. Control and address bus inputs are stable during deselects.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
27
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Electrical Specifications – IDD Parameters
Table 10: DDR2 IDD Specifications and Conditions (Die Revisions E, G, and H)
Notes: 1–7 apply to the entire table
-25E/
-25
-3E/
-3
Parameter/Condition
Symbol Configuration -187E
-37E
70
-5E
70
Units
Operating one bank active-
precharge current:
IDD0
x4, x8
x16
115
180
90
85
mA
150
135
110
110
tCK = tCK (IDD), tRC = tRC (IDD), tRAS
= tRAS MIN (IDD); CKE is HIGH, CS# is
HIGH between valid commands; Ad-
dress bus inputs are switching; Data
bus inputs are switching
Operating one bank active-read-
precharge current: IOUT = 0mA; BL
= 4, CL = CL (IDD), AL = 0; tCK = tCK
(IDD), tRC = tRC (IDD), tRAS = tRAS
MIN (IDD), tRCD = tRCD (IDD); CKE is
HIGH, CS# is HIGH between valid
commands; Address bus inputs are
switching; Data pattern is same as
IDD4W
IDD1
x4, x8
x16
130
210
110
175
100
130
95
90
mA
120
115
Precharge power-down current:
All banks idle; tCK = tCK (IDD); CKE
is LOW; Other control and address
bus inputs are stable; Data bus in-
puts are floating
IDD2P
x4, x8, x16
7
7
7
7
7
mA
mA
Precharge quiet standby
current: All banks idle;
tCK = tCK (IDD); CKE is HIGH, CS# is
HIGH; Other control and address
bus inputs are stable; Data bus in-
puts are floating
IDD2Q
x4, x8
x16
60
90
50
75
40
65
40
45
35
40
Precharge standby current: All
banks idle; tCK = tCK (IDD); CKE is
HIGH, CS# is HIGH; Other control
and address bus inputs are switch-
ing; Data bus inputs are switching
IDD2N
x4, x8
x16
60
95
50
80
40
70
40
50
35
40
mA
mA
mA
Active power-down current: All
banks open; tCK = tCK (IDD); CKE is
LOW; Other control and address
bus inputs are stable; Data bus in-
puts are floating
IDD3Pf
IDD3Ps
Fast exit
MR12 = 0
50
10
40
10
30
10
30
10
30
10
Slow exit
MR12 = 1
Active standby current: All banks
open; tCK = tCK (IDD), tRAS = tRAS
MAX (IDD), tRP = tRP (IDD); CKE is
HIGH, CS# is HIGH between valid
commands; Other control and ad-
dress bus inputs are switching; Data
bus inputs are switching
IDD3N
x4, x8
x16
70
95
60
85
55
75
45
60
40
55
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
28
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Electrical Specifications – IDD Parameters
Table 10: DDR2 IDD Specifications and Conditions (Die Revisions E, G, and H) (Continued)
Notes: 1–7 apply to the entire table
-25E/
-25
-3E/
-3
Parameter/Condition
Symbol Configuration -187E
-37E
110
125
180
-5E
90
Units
Operating burst write current:
All banks open, continuous burst
writes; BL = 4, CL = CL (IDD), AL = 0;
tCK = tCK (IDD), tRAS = tRAS MAX
(IDD), tRP = tRP (IDD); CKE is HIGH,
CS# is HIGH between valid com-
mands; Address bus inputs are
switching; Data bus inputs are
switching
IDD4W
IDD4R
IDD5
x4
x8
190
210
405
145
160
315
120
135
200
mA
105
160
x16
Operating burst read current:
All banks open, continuous burst
reads, IOUT = 0mA; BL = 4, CL = CL
(IDD), AL = 0; tCK = tCK (IDD), tRAS =
tRAS MAX (IDD), tRP = tRP (IDD); CKE
is HIGH, CS# is HIGH between valid
commands; Address bus inputs are
switching; Data bus inputs are
switching
Burst refresh current: tCK = tCK
(IDD); REFRESH command at every
tRFC (IDD) interval; CKE is HIGH, CS#
is HIGH between valid commands;
Other control and address bus in-
puts are switching; Data bus inputs
are switching
x4
x8
190
210
420
145
160
320
120
135
220
110
125
180
90
mA
105
160
x16
x4, x8
x16
265
300
235
280
215
270
210
250
205
240
mA
Self refresh current: CK and CK#
at 0V; CKE ≤ 0.2V; Other control
and address bus inputs are floating;
Data bus inputs are floating
IDD6
x4, x8, x16
7
5
7
5
7
5
7
5
7
5
mA
mA
IDD6L
Operating bank interleave read
current: All bank interleaving
reads, IOUT = 0mA; BL = 4, CL = CL
(IDD), AL = tRCD (IDD) - 1 × tCK (IDD);
tCK = tCK (IDD), tRC = tRC (IDD), tRRD
= tRRD (IDD), tRCD = tRCD (IDD); CKE
is HIGH, CS# is HIGH between valid
commands; Address bus inputs are
stable during deselects; Data bus in-
puts are switching; See on page
for details
IDD7
x4, x8
x16
425
520
335
440
280
350
270
330
260
300
1.
Notes:
IDD specifications are tested after the device is properly initialized. 0°C ≤ TC ≤ +85°C.
2. VDD = +1.8V ±0.1V, VDDQ = +1.8V ±0.1V, VDDL = +1.8V ±0.1V, VREF = VDDQ/2.
3. IDD parameters are specified with ODT disabled.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2004 Micron Technology, Inc. All rights reserved.
29
1Gb: x4, x8, x16 DDR2 SDRAM
Electrical Specifications – IDD Parameters
4. Data bus consists of DQ, DM, DQS, DQS#, RDQS, RDQS#, LDQS, LDQS#, UDQS, and
UDQS#. IDD values must be met with all combinations of EMR bits 10 and 11.
5. Definitions for IDD conditions:
LOW
VIN ≤ VIL(AC)max
HIGH
Stable
VIN ≥ VIH(AC)min
Inputs stable at a HIGH or LOW level
Floating Inputs at VREF = VDDQ/2
Switching Inputs changing between HIGH and LOW every other clock cycle (once per
two clocks) for address and control signals
Switching Inputs changing between HIGH and LOW every other data transfer (once
per clock) for DQ signals, not including masks or strobes
6. IDD1, IDD4R, and IDD7 require A12 in EMR to be enabled during testing.
7. The following IDD values must be derated (IDD limits increase) on IT-option and AT-op-
tion devices when operated outside of the range 0°C ≤ TC ≤ 85°C:
When
TC ≤ 0°C
IDD2P and IDD3P(SLOW) must be derated by 4%; IDD4R and IDD5W must be derat-
ed by 2%; and IDD6 and IDD7 must be derated by 7%
When
TC ≥ 85°C
IDD0, IDD1, IDD2N, IDD2Q, IDD3N, IDD3P(FAST), IDD4R, IDD4W, and IDD5W must be derat-
ed by 2%; IDD2P must be derated by 20%; IDD3P(SLOW) must be derated by
30%; and IDD6 must be derated by 80% (IDD6 will increase by this amount if
TC < 85°C and the 2X refresh option is still enabled)
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
30
© 2004 Micron Technology, Inc. All rights reserved.
AC Timing Operating Specifications
Table 11: AC Operating Specifications and Conditions
Not all speed grades listed may be supported for this device; refer to the title page for speeds supported; Notes: 1–5 apply to the entire table;
VDDQ = +1.8V ±0.1V, VDD = +1.8V ±0.1V
AC Characteristics
Parameter Symbol Min
Clock
cycle time
-187E
-25E
-25
-3E
-3
-37E
-5E
Max Min Max Min Max Min Max Min Max Min Max Min Max Units Notes
CL = 7 tCK (avg) 1.875
CL = 6 tCK (avg) 2.5
CL = 5 tCK (avg) 3.0
CL = 4 tCK (avg) 3.75
8.0
8.0
ns
6, 7, 8,
9
–
–
–
–
–
–
–
–
3.0
3.75
5.0
–
–
–
–
–
–
–
–
–
2.5
2.5
3.75
5.0
8.0
8.0
8.0
8.0
2.5
3.0
3.75
5.0
8.0
8.0
8.0
8.0
–
–
–
8.0
3.0
3.0
5.0
8.0
8.0
8.0
8.0
8.0
8.0
–
–
8.0
–
–
8.0
8.0
3.75
5.0
CL = 3 tCK (avg) 5.0
8.0
5.0
8.0
5.0
8.0
t
CK high-level width CH (avg) 0.48
CK low-level width tCL (avg) 0.48
0.52
0.52
0.48 0.52 0.48 0.52 0.48 0.52 0.48 0.52 0.48 0.52 0.48 0.52 tCK
0.48 0.52 0.48 0.52 0.48 0.52 0.48 0.52 0.48 0.52 0.48 0.52 tCK
10
11
Half clock period
tHP
MIN = lesser of tCH and tCL
MAX = n/a
ps
ps
ps
ps
Absolute tCK
tCK (abs)
tCH (abs)
tCL (abs)
MIN = tCK (AVG) MIN + tJITper (MIN)
MAX = tCK (AVG) MAX + tJITper (MAX)
Absolute CK
high-level width
MIN = tCK (AVG) MIN × tCH (AVG) MIN + tJITdty (MIN)
MAX = tCK (AVG) MAX × tCH (AVG) MAX + tJITdty (MAX)
Absolute CK
low-level width
MIN = tCK (AVG) MIN × tCL (AVG) MIN + tJITdty (MIN)
MAX = tCK (AVG) MAX × tCL (AVG) MAX + tJITdty (MAX)
Period jitter
Half period
Cycle to cycle
tJITper
tJITdty
tJITcc
tERR2per –132
tERR3per –157
tERR4per –175
tERR5per –188
–90
–75
90
75
–100 100 –100 100 –125 125 –125 125 –125 125 –125 125
–100 100 –100 100 –125 125 –125 125 –125 125 –150 150
ps
ps
ps
ps
12
13
14
15
180
200
200
250
250
250
250
Cumulative error,
2 cycles
132
157
175
188
250
425
–150 150 –150 150 –175 175 –175 175 –175 175 –175 175
–175 175 –175 175 –225 225 –225 225 –225 225 –225 225
–200 200 –200 200 –250 250 –250 250 –250 250 –250 250
–200 200 –200 200 –250 250 –250 250 –250 250 –250 250
–300 300 –300 300 –350 350 –350 350 –350 350 –350 350
–450 450 –450 450 –450 450 –450 450 –450 450 –450 450
Cumulative error,
3 cycles
ps
ps
ps
ps
ps
15
15
Cumulative error,
4 cycles
Cumulative error,
5 cycles
15, 16
15, 16
15
Cumulative error,
6–10 cycles
tERR6–
10per
tERR11–
50per
–250
–425
Cumulative error,
11–50 cycles
Table 11: AC Operating Specifications and Conditions (Continued)
Not all speed grades listed may be supported for this device; refer to the title page for speeds supported; Notes: 1–5 apply to the entire table;
VDDQ = +1.8V ±0.1V, VDD = +1.8V ±0.1V
AC Characteristics
-187E
-25E
-25
-3E
-3
-37E
-5E
Parameter Symbol Min
Max Min Max Min Max Min Max Min Max Min Max Min Max Units Notes
DQS output access tDQSCK –300 +300 –350 +350 –350 +350 –400 +400 –400 +400 –450 +450 –500 +500
time from CK/CK#
ps
19
DQS read preamble tRPRE
MIN = 0.9 × tCK
MAX = 1.1 × tCK
tCK 17, 18,
19
DQS read
postamble
tRPST
tLZ1
MIN = 0.4 × tCK
MAX = 0.6 × tCK
tCK 17, 18,
19, 20
t
CK/CK# to DQS
Low-Z
MIN = AC (MIN)
ps
19, 21,
22
t
MAX = AC (MAX)
DQS rising edge to
CK rising edge
tDQSS
tDQSH
tDQSL
tDSS
MIN = –0.25 × tCK
MAX = +0.25 × tCK
MIN = 0.35 × tCK
MAX = n/a
MIN = 0.35 × tCK
MAX = n/a
MIN = 0.2 × tCK
MAX = n/a
tCK
tCK
tCK
tCK
tCK
18
18
18
18
18
DQS input-high
pulse width
DQS input-low
pulse width
DQS falling to CK
rising: setup time
DQS falling from
CK rising:
tDSH
MIN = 0.2 × tCK
MAX = n/a
hold time
Write preamble
setup time
tWPRES
tWPRE
tWPST
–
MIN = 0
MAX = n/a
MIN = 0.35 × tCK
MAX = n/a
MIN = 0.4 × tCK
MAX = 0.6 × tCK
ps
23, 24
18
DQS write
preamble
tCK
DQS write
postamble
tCK 18, 25
tCK
WRITE command
to first DQS
transition
MIN = WL - tDQSS
MAX = WL + tDQSS
Table 11: AC Operating Specifications and Conditions (Continued)
Not all speed grades listed may be supported for this device; refer to the title page for speeds supported; Notes: 1–5 apply to the entire table;
VDDQ = +1.8V ±0.1V, VDD = +1.8V ±0.1V
AC Characteristics
-187E
-25E
-25
-3E
-3
-37E
-5E
Parameter
Symbol Min Max Min Max Min Max Min Max Min Max Min Max Min Max Units Notes
DQ output access
time from CK/CK#
tAC
–350 +350 –400 +400 –400 +400 –450 +450 –450 +450 –500 +500 –600 +600
ps
ps
19
DQS–DQ skew,
DQS to last DQ
valid, per group,
per access
tDQSQ
175
200
200
240
240
300
350
26, 27
–
–
–
–
–
–
–
DQ hold from next
DQS strobe
tQHS
tQH
250
300
300
340
340
400
450
ps
ps
ps
ps
ns
ps
ps
ps
ps
28
–
–
–
–
–
–
–
DQ–DQS hold, DQS
to first DQ not valid
MIN = tHP - tQHS
MAX = n/a
26, 27,
28
CK/CK# to DQ, DQS
High-Z
tHZ
MIN = n/a
19, 21,
29
MAX = tAC (MAX)
MIN = 2 × tAC (MIN)
MAX = tAC (MAX)
MIN = tQH - tDQSQ
MAX = n/a
CK/CK# to DQ
Low-Z
tLZ2
19, 21,
22
Data valid output
window
DVW
tDSb
tDHb
tDSa
tDHa
tDIPW
26, 27
DQ and DM input
setup time to DQS
0
50
50
100
100
175
300
300
100
225
350
350
150
275
400
400
26, 30,
31
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
DQ and DM input
hold time to DQS
75
125
250
250
125
250
250
175
300
300
26, 30,
31
DQ and DM input
setup time to DQS
200
200
26, 30,
31
DQ and DM input
hold time to DQS
26, 30,
31
DQ and DM input
pulse width
MIN = 0.35 × tCK
MAX = n/a
tCK 18, 32
Table 11: AC Operating Specifications and Conditions (Continued)
Not all speed grades listed may be supported for this device; refer to the title page for speeds supported; Notes: 1–5 apply to the entire table;
VDDQ = +1.8V ±0.1V, VDD = +1.8V ±0.1V
AC Characteristics
-187E
-25E
-25
-3E
-3
-37E
-5E
Parameter
Symbol Min Max Min Max Min Max Min Max Min Max Min Max Min Max Units Notes
Input setup time
Input hold time
Input setup time
Input hold time
Input pulse width
tISb
tIHb
tISa
tIHa
tIPW
tRC
125
200
325
325
0.6
175
250
375
375
0.6
175
250
375
375
0.6
200
275
400
400
0.6
200
275
400
400
0.6
250
375
500
500
0.6
350
475
600
600
0.6
ps
ps
ps
ps
31, 33
31, 33
31, 33
31, 33
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
tCK 18, 32
ACTIVATE-to-
ACTIVATE delay,
same bank
54
55
55
54
55
55
55
ns
18, 34
ACTIVATE-to-READ
or WRITE delay
tRCD
tRAS
13.125
40
12.5
40
15
40
12
40
15
40
15
40
15
40
ns
ns
18
–
–
–
–
–
–
–
ACTIVATE-to-
PRECHARGE delay
70K
70K
70K
70K
70K
70K
70K
18, 34,
35
PRECHARGE period
tRP
tRPA
tRPA
13.125
13.125
15
12.5
12.5
15
15
15
12
12
15
15
15
18
15
15
15
15
20
ns
ns
ns
18, 36
18, 36
18, 36
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
PRE-
<1Gb
CHARGE
ALL period
17.5
18.75
≥1Gb
ACTIVATE x4, x8
tRRD
tRRD
7.5
10
7.5
10
7.5
10
7.5
10
7.5
10
7.5
10
7.5
10
ns
ns
18, 37
18, 37
–
–
–
–
–
–
–
–
–
–
–
–
–
–
-to-
x16
ACTIVATE
delay
different
bank
4-bank
activate
period
(≥1Gb)
x4, x8
x16
tFAW
tFAW
35
45
35
45
35
45
37.5
50
37.5
50
37.5
50
37.5
50
ns
ns
18, 38
18, 38
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Table 11: AC Operating Specifications and Conditions (Continued)
Not all speed grades listed may be supported for this device; refer to the title page for speeds supported; Notes: 1–5 apply to the entire table;
VDDQ = +1.8V ±0.1V, VDD = +1.8V ±0.1V
AC Characteristics
-187E
-25E
-25
-3E
-3
-37E
-5E
Parameter
Symbol Min Max Min Max Min Max Min Max Min Max Min Max Min Max Units Notes
Internal READ-to-
PRECHARGE delay
tRTP
7.5
2
7.5
2
7.5
2
7.5
2
7.5
2
7.5
2
7.5
2
ns
18, 37,
39
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CAS#-to-CAS#
delay
tCCD
tCK
18
Write recovery time
tWR
tDAL
15
tWR +
tRP
15
tWR +
tRP
15
tWR +
tRP
15
tWR +
tRP
15
tWR +
tRP
15
tWR +
tRP
15
tWR +
tRP
ns
ns
18, 37
40
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Write AP recovery
+ precharge time
Internal WRITE-to-
READ delay
tWTR
tMRD
tRFC
7.5
7.5
7.5
7.5
7.5
7.5
10
ns
tCK
ns
18, 37
18
–
–
–
–
–
–
–
–
–
–
–
–
–
–
LOAD MODE cycle
time
2
2
2
2
2
2
2
REFRESH- 256Mb
75
75
75
75
75
75
75
18, 41
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
to-
ACTIVATE
or to
-REFRESH
interval
512Mb
1Gb
105
105
105
105
105
105
105
127.5
197.5
127.5
197.5
127.5
197.5
127.5
197.5
127.5
197.5
127.5
197.5
127.5
197.5
2Gb
Average periodic
refresh
(commercial)
tREFI
tREFIIT
tREFIAT
tDELAY
7.8
3.9
3.9
7.8
3.9
3.9
7.8
3.9
3.9
7.8
3.9
3.9
7.8
3.9
3.9
7.8
3.9
3.9
7.8
3.9
3.9
µs
µs
µs
ns
18, 41
18, 41
18, 41
42
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Average periodic
refresh
(industrial)
Average periodic
refresh
(automotive)
CKE LOW to CK,
CK# uncertainty
MIN limit = tIS + tCK + tIH
MAX limit = n/a
Table 11: AC Operating Specifications and Conditions (Continued)
Not all speed grades listed may be supported for this device; refer to the title page for speeds supported; Notes: 1–5 apply to the entire table;
VDDQ = +1.8V ±0.1V, VDD = +1.8V ±0.1V
AC Characteristics
-187E
-25E
-25
-3E
-3
-37E
-5E
Parameter
Symbol Min Max Min Max Min Max Min Max Min Max Min Max Min Max Units Notes
Exit SELF REFRESH
to nonREAD
command
tXSNR
MIN limit = tRFC (MIN) + 10
MAX limit = n/a
ns
Exit SELF REFRESH
to READ command
tXSRD
tISXR
MIN limit = 200
MAX limit = n/a
MIN limit = tIS
tCK
ps
18
33, 43
18
Exit SELF REFRESH
timing reference
Exit active MR12 tXARD
MAX limit = n/a
3
2
2
2
2
2
2
tCK
tCK
–
–
–
–
–
–
–
–
–
–
–
–
–
power-
down to
READ
= 0
MR12
= 1
10 - AL
8 - AL
8 - AL
7 - AL
7 - AL
6 - AL
6 - AL
18
–
command
Exit precharge
power-down and
active power-down
to any
tXP
3
2
2
2
2
2
2
tCK
18
–
–
–
–
–
–
–
nonREAD
command
CKE MIN HIGH/
LOW time
tCKE
MIN = 3
MAX = n/a
tCK 18, 44
Table 11: AC Operating Specifications and Conditions (Continued)
Not all speed grades listed may be supported for this device; refer to the title page for speeds supported; Notes: 1–5 apply to the entire table;
VDDQ = +1.8V ±0.1V, VDD = +1.8V ±0.1V
AC Characteristics
-187E
-25E
-25
-3E
-3
-37E
-5E
Parameter
Symbol Min Max Min Max Min Max Min Max Min Max Min Max Min Max Units Notes
ODT to power-
down entry latency
tANPD
tAXPD
4
3
3
3
8
3
8
3
8
3
8
tCK
tCK
tCK
18
18
18
–
–
–
–
–
–
–
–
–
–
–
–
–
–
ODT power-down
exit latency
ODT turn-on delay tAOND
ODT turn-off delay tAOFD
11
10
10
2
2.5
tCK 18, 45
ODT turn-on
tAON
tAC
tAC
MIN = tAC (MIN)
MIN = tAC (MIN)
MAX = tAC (MAX) + 700
MIN = tAC (MIN)
MAX = tAC (MAX) + 1,000
ps
19, 46
(MIN) (MAX) MAX = tAC (MAX) + 600
+
2,575
ODT turn-off
tAOF
MIN = tAC (MIN)
ps
ps
47, 48
49
MAX = tAC (MAX) + 600
ODT turn-on
(power-down
mode)
tAONPD
tAC
(MIN) tCK +
tAC
2 ×
MIN = tAC (MIN) + 2,000
MAX = 2 × tCK + tAC (MAX) + 1,000
+
2,000 (MAX)
+
1,000
ODT turn-off
(power-down
mode)
tAOFPD
tMOD
MIN = tAC (MIN) + 2,000
ps
ns
MAX = 2.5 × tCK + tAC (MAX) + 1,000
ODT enable from
MRS command
MIN = 12
MAX = n/a
18, 50
1Gb: x4, x8, x16 DDR2 SDRAM
1. All voltages are referenced to VSS.
Notes:
2. Tests for AC timing, IDD, and electrical AC and DC characteristics may be conducted at
nominal reference/supply voltage levels, but the related specifications and the opera-
tion of the device are warranted for the full voltage range specified. ODT is disabled for
all measurements that are not ODT-specific.
3. Outputs measured with equivalent load (see Figure 15 (page 47)).
4. AC timing and IDD tests may use a VIL-to-VIH swing of up to 1.0V in the test environment,
and parameter specifications are guaranteed for the specified AC input levels under nor-
mal use conditions. The slew rate for the input signals used to test the device is 1.0 V/ns
for signals in the range between VIL(AC) and VIH(AC). Slew rates other than 1.0 V/ns may
require the timing parameters to be derated as specified.
5. The AC and DC input level specifications are as defined in the SSTL_18 standard (that is,
the receiver will effectively switch as a result of the signal crossing the AC input level
and will remain in that state as long as the signal does not ring back above [below] the
DC input LOW [HIGH] level).
6. CK and CK# input slew rate is referenced at 1 V/ns (2 V/ns if measured differentially).
7. Operating frequency is only allowed to change during self refresh mode (see Figure 78
(page 122)), precharge power-down mode, or system reset condition (see Reset
(page 123)). SSC allows for small deviations in operating frequency, provided the SSC
guidelines are satisfied.
8. The clock’s tCK (AVG) is the average clock over any 200 consecutive clocks and
tCK (AVG) MIN is the smallest clock rate allowed (except for a deviation due to allowed
clock jitter). Input clock jitter is allowed provided it does not exceed values specified.
Also, the jitter must be of a random Gaussian distribution in nature.
9. Spread spectrum is not included in the jitter specification values. However, the input
clock can accommodate spread spectrum at a sweep rate in the range 8–60 kHz with an
additional one percent tCK (AVG); however, the spread spectrum may not use a clock
rate below tCK (AVG) MIN or above tCK (AVG) MAX.
10. MIN (tCL, tCH) refers to the smaller of the actual clock LOW time and the actual clock
HIGH time driven to the device. The clock’s half period must also be of a Gaussian distri-
bution; tCH (AVG) and tCL (AVG) must be met with or without clock jitter and with or
without duty cycle jitter. tCH (AVG) and tCL (AVG) are the average of any 200 consecu-
tive CK falling edges. tCH limits may be exceeded if the duty cycle jitter is small enough
that the absolute half period limits (tCH [ABS], tCL [ABS]) are not violated.
11. tHP (MIN) is the lesser of tCL and tCH actually applied to the device CK and CK# inputs;
thus, tHP (MIN) ≥ the lesser of tCL (ABS) MIN and tCH (ABS) MIN.
12. The period jitter (tJITper) is the maximum deviation in the clock period from the average
or nominal clock allowed in either the positive or negative direction. JEDEC specifies
tighter jitter numbers during DLL locking time. During DLL lock time, the jitter values
should be 20 percent less those than noted in the table (DLL locked).
13. The half-period jitter (tJITdty) applies to either the high pulse of clock or the low pulse
of clock; however, the two cumulatively can not exceed tJITper.
14. The cycle-to-cycle jitter (tJITcc) is the amount the clock period can deviate from one cycle
to the next. JEDEC specifies tighter jitter numbers during DLL locking time. During DLL
lock time, the jitter values should be 20 percent less than those noted in the table (DLL
locked).
15. The cumulative jitter error (tERRnper), where n is 2, 3, 4, 5, 6–10, or 11–50 is the amount
of clock time allowed to consecutively accumulate away from the average clock over
any number of clock cycles.
16. JEDEC specifies using tERR6–10per when derating clock-related output timing (see notes
19 and 48). Micron requires less derating by allowing tERR5per to be used.
17. This parameter is not referenced to a specific voltage level but is specified when the de-
vice output is no longer driving (tRPST) or beginning to drive (tRPRE).
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
38
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
18. The inputs to the DRAM must be aligned to the associated clock, that is, the actual clock
that latches it in. However, the input timing (in ns) references to the tCK (AVG) when
determining the required number of clocks. The following input parameters are deter-
mined by taking the specified percentage times the tCK (AVG) rather than tCK: tIPW,
tDIPW, tDQSS, tDQSH, tDQSL, tDSS, tDSH, tWPST, and tWPRE.
19. The DRAM output timing is aligned to the nominal or average clock. Most output param-
eters must be derated by the actual jitter error when input clock jitter is present; this
will result in each parameter becoming larger. The following parameters are required to
be derated by subtracting tERR5per (MAX): tAC (MIN), tDQSCK (MIN), tLZDQS (MIN), tLZDQ
(MIN), tAON (MIN); while the following parameters are required to be derated by sub-
tracting tERR5per (MIN): tAC (MAX), tDQSCK (MAX), tHZ (MAX), tLZDQS (MAX), tLZDQ
(MAX), tAON (MAX). The parameter tRPRE (MIN) is derated by subtracting tJITper (MAX),
while tRPRE (MAX), is derated by subtracting tJITper (MIN). The parameter tRPST (MIN) is
derated by subtracting tJITdty (MAX), while tRPST (MAX), is derated by subtracting tJITd-
ty (MIN). Output timings that require tERR5per derating can be observed to have offsets
relative to the clock; however, the total window will not degrade.
20. When DQS is used single-ended, the minimum limit is reduced by 100ps.
21. tHZ and tLZ transitions occur in the same access time windows as valid data transitions.
These parameters are not referenced to a specific voltage level, but specify when the
device output is no longer driving (tHZ) or begins driving (tLZ).
22. tLZ (MIN) will prevail over a tDQSCK (MIN) + tRPRE (MAX) condition.
23. This is not a device limit. The device will operate with a negative value, but system per-
formance could be degraded due to bus turnaround.
24. It is recommended that DQS be valid (HIGH or LOW) on or before the WRITE command.
The case shown (DQS going from High-Z to logic LOW) applies when no WRITEs were
previously in progress on the bus. If a previous WRITE was in progress, DQS could be
HIGH during this time, depending on tDQSS.
25. The intent of the “Don’t Care” state after completion of the postamble is that the DQS-
driven signal should either be HIGH, LOW, or High-Z, and that any signal transition
within the input switching region must follow valid input requirements. That is, if DQS
transitions HIGH (above VIH[DC]min), then it must not transition LOW (below VIH[DC]) prior
to tDQSH (MIN).
26. Referenced to each output group: x4 = DQS with DQ0–DQ3; x8 = DQS with DQ0–DQ7;
x16 = LDQS with DQ0–DQ7; and UDQS with DQ8–DQ15.
27. The data valid window is derived by achieving other specifications: tHP (tCK/2), tDQSQ,
and tQH (tQH = tHP - tQHS). The data valid window derates in direct proportion to the
clock duty cycle and a practical data valid window can be derived.
28. tQH = tHP - tQHS; the worst case tQH would be the lesser of tCL (ABS) MAX or
tCH (ABS) MAX times tCK (ABS) MIN - tQHS. Minimizing the amount of tCH (AVG) offset
and value of tJITdty will provide a larger tQH, which in turn will provide a larger valid
data out window.
29. This maximum value is derived from the referenced test load. tHZ (MAX) will prevail
over tDQSCK (MAX) + tRPST (MAX) condition.
30. The values listed are for the differential DQS strobe (DQS and DQS#) with a differential
slew rate of 2 V/ns (1 V/ns for each signal). There are two sets of values listed: tDSa, tDHa
and tDSb, tDHb. The tDSa, tDHa values (for reference only) are equivalent to the baseline
values of tDSb, tDHb at VREF when the slew rate is 2 V/ns, differentially. The baseline val-
ues, tDSb, tDHb, are the JEDEC-defined values, referenced from the logic trip points. tDSb
is referenced from VIH(AC) for a rising signal and VIL(AC) for a falling signal, while tDHb is
referenced from VIL(DC) for a rising signal and VIH(DC) for a falling signal. If the differen-
tial DQS slew rate is not equal to 2 V/ns, then the baseline values must be derated by
adding the values from Table 30 (page 60) and Table 31 (page 61). If the DQS differ-
ential strobe feature is not enabled, then the DQS strobe is single-ended and the
baseline values must be derated using Table 32 (page 62). Single-ended DQS data tim-
ing is referenced at DQS crossing VREF. The correct timing values for a single-ended DQS
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
39
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
strobe are listed in Table 33 (page 62)–Table 35 (page 63) on Table 33 (page 62),
Table 34 (page 63), and Table 35 (page 63); listed values are already derated for slew
rate variations and converted from baseline values to VREF values.
31. VIL/VIH DDR2 overshoot/undershoot. See AC Overshoot/Undershoot Specification
(page 53).
32. For each input signal—not the group collectively.
33. There are two sets of values listed for command/address: tISa, tIHa and tISb, tIHb. The tISa,
tIHa values (for reference only) are equivalent to the baseline values of tISb, tIHb at VREF
when the slew rate is 1 V/ns. The baseline values, tISb, tIHb, are the JEDEC-defined values,
referenced from the logic trip points. tISb is referenced from VIH(AC) for a rising signal
and VIL(AC) for a falling signal, while tIHb is referenced from VIL(DC) for a rising signal and
VIH(DC) for a falling signal. If the command/address slew rate is not equal to 1 V/ns, then
the baseline values must be derated by adding the values from Table 28 (page 56) and
Table 29 (page 57).
34. This is applicable to READ cycles only. WRITE cycles generally require additional time
due to tWR during auto precharge.
35. READs and WRITEs with auto precharge are allowed to be issued before tRAS (MIN) is
satisfied because tRAS lockout feature is supported in DDR2 SDRAM.
36. When a single-bank PRECHARGE command is issued, tRP timing applies. tRPA timing ap-
plies when the PRECHARGE (ALL) command is issued, regardless of the number of banks
open. For 8-bank devices (≥1Gb), tRPA (MIN) = tRP (MIN) + tCK (AVG) (Table 11 (page 31)
lists tRP [MIN] + tCK [AVG] MIN).
37. This parameter has a two clock minimum requirement at any tCK.
38. The tFAW (MIN) parameter applies to all 8-bank DDR2 devices. No more than four bank-
ACTIVATE commands may be issued in a given tFAW (MIN) period. tRRD (MIN) restriction
still applies.
39. The minimum internal READ-to-PRECHARGE time. This is the time from which the last 4-
bit prefetch begins to when the PRECHARGE command can be issued. A 4-bit prefetch is
when the READ command internally latches the READ so that data will output CL later.
This parameter is only applicable when tRTP/(2 × tCK) > 1, such as frequencies faster than
533 MHz when tRTP = 7.5ns. If tRTP/(2 × tCK) ≤ 1, then equation AL + BL/2 applies. tRAS
(MIN) has to be satisfied as well. The DDR2 SDRAM will automatically delay the internal
PRECHARGE command until tRAS (MIN) has been satisfied.
40. tDAL = (nWR) + (tRP/tCK). Each of these terms, if not already an integer, should be roun-
ded up to the next integer. tCK refers to the application clock period; nWR refers to the
tWR parameter stored in the MR9–MR11. For example, -37E at tCK = 3.75ns with tWR
programmed to four clocks would have tDAL = 4 + (15ns/3.75ns) clocks = 4 + (4) clocks =
8 clocks.
41. The refresh period is 64ms (commercial) or 32ms (industrial and automotive). This equa-
tes to an average refresh rate of 7.8125µs (commercial) or 3.9607µs (industrial and
automotive). To ensure all rows of all banks are properly refreshed, 8192 REFRESH com-
mands must be issued every 64ms (commercial) or 32ms (industrial and automotive). The
JEDEC tRFC MAX of 70,000ns is not required as bursting of AUTO REFRESH commands is
allowed.
42. tDELAY is calculated from tIS + tCK + tIH so that CKE registration LOW is guaranteed pri-
or to CK, CK# being removed in a system RESET condition (see Reset (page 123)).
43. tISXR is equal to tIS and is used for CKE setup time during self refresh exit, as shown in
Figure 68 (page 114).
44. tCKE (MIN) of three clocks means CKE must be registered on three consecutive positive
clock edges. CKE must remain at the valid input level the entire time it takes to achieve
the three clocks of registration. Thus, after any CKE transition, CKE may not transition
from its valid level during the time period of tIS + 2 × tCK + tIH.
45. The half-clock of tAOFD’s 2.5 tCK assumes a 50/50 clock duty cycle. This half-clock value
must be derated by the amount of half-clock duty cycle error. For example, if the clock
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
40
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
AC and DC Operating Conditions
duty cycle was 47/53, tAOFD would actually be 2.5 - 0.03, or 2.47, for tAOF (MIN) and 2.5
+ 0.03, or 2.53, for tAOF (MAX).
46. ODT turn-on time tAON (MIN) is when the device leaves High-Z and ODT resistance be-
gins to turn on. ODT turn-on time tAON (MAX) is when the ODT resistance is fully on.
Both are measured from tAOND.
47. ODT turn-off time tAOF (MIN) is when the device starts to turn off ODT resistance. ODT
turn off time tAOF (MAX) is when the bus is in High-Z. Both are measured from tAOFD.
48. Half-clock output parameters must be derated by the actual tERR5per and tJITdty when
input clock jitter is present; this will result in each parameter becoming larger. The pa-
rameter tAOF (MIN) is required to be derated by subtracting both tERR5per (MAX) and
tJITdty (MAX). The parameter tAOF (MAX) is required to be derated by subtracting both
tERR5per (MIN) and tJITdty (MIN).
49. The -187E maximum limit is 2 × tCK + tAC (MAX) + 1000 but it will likely be
3 x tCK + tAC (MAX) + 1000 in the future.
50. Should use 8 tCK for backward compatibility.
AC and DC Operating Conditions
Table 12: Recommended DC Operating Conditions (SSTL_18)
All voltages referenced to VSS
Parameter
Symbol
VDD
Min
1.7
Nom
1.8
Max
1.9
Units Notes
Supply voltage
V
V
1, 2
2, 3
2, 3
4
VDDL supply voltage
I/O supply voltage
I/O reference voltage
I/O termination voltage (system)
VDDL
1.7
1.8
1.9
VDDQ
VREF(DC)
VTT
1.7
1.8
1.9
V
0.49 × VDDQ
VREF(DC) - 40
0.50 × VDDQ
VREF(DC)
0.51 × VDDQ
VREF(DC) + 40
V
mV
5
1.
Notes:
VDD and VDDQ must track each other. VDDQ must be ≤ VDD.
2. VSSQ = VSSL = VSS.
3. VDDQ tracks with VDD; VDDL tracks with VDD
.
4. VREF is expected to equal VDDQ/2 of the transmitting device and to track variations in the
DC level of the same. Peak-to-peak noise (noncommon mode) on VREF may not exceed
±1 percent of the DC value. Peak-to-peak AC noise on VREF may not exceed ±2 percent
of VREF(DC). This measurement is to be taken at the nearest VREF bypass capacitor.
5. VTT is not applied directly to the device. VTT is a system supply for signal termination
resistors, is expected to be set equal to VREF, and must track variations in the DC level of
VREF
.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
41
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
ODT DC Electrical Characteristics
ODT DC Electrical Characteristics
Table 13: ODT DC Electrical Characteristics
All voltages are referenced to VSS
Parameter
Symbol
Min
Nom
Max
Units
Notes
RTT1(EFF)
60
75
90
1, 2
RTT effective impedance value for 75Ω setting
Ω
EMR (A6, A2) = 0, 1
RTT2(EFF)
RTT3(EFF)
ΔVM
120
40
150
50
–
180
60
6
1, 2
1, 2
3
RTT effective impedance value for 150Ω setting
EMR (A6, A2) = 1, 0
Ω
Ω
RTT effective impedance value for 50Ω setting
EMR (A6, A2) = 1, 1
Deviation of VM with respect to VDDQ/2
–6
%
1. RTT1(EFF) and RTT2(EFF) are determined by separately applying VIH(AC) and VIL(DC) to the ball
being tested, and then measuring current, I(VIH[AC]), and I(VIL[AC]), respectively.
Notes:
2. Minimum IT and AT device values are derated by six percent when the devices operate
between –40°C and 0°C (TC ).
3. Measure voltage (VM) at tested ball with no load.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
42
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Input Electrical Characteristics and Operating Conditions
Input Electrical Characteristics and Operating Conditions
Table 14: Input DC Logic Levels
All voltages are referenced to VSS
Parameter
Symbol
VIH(DC)
VIL(DC)
Min
VREF(DC) + 125
–300
Max
Units
mV
1
Input high (logic 1) voltage
Input low (logic 0) voltage
VDDQ
VREF(DC) - 125
mV
1. VDDQ + 300mV allowed provided 1.9V is not exceeded.
Note:
Table 15: Input AC Logic Levels
All voltages are referenced to VSS
Parameter
Symbol
VIH(AC)
VIH(AC)
VIL(AC)
Min
VREF(DC) + 250
VREF(DC) + 200
–300
Max
Units
mV
1
Input high (logic 1) voltage (-37E/-5E)
VDDQ
VDDQ
1
Input high (logic 1) voltage (-187E/-25E/-25/-3E/-3)
Input low (logic 0) voltage (-37E/-5E)
mV
VREF(DC) - 250
VREF(DC) - 200
mV
Input low (logic 0) voltage (-187E/-25E/-25/-3E/-3)
VIL(AC)
–300
mV
1. Refer to AC Overshoot/Undershoot Specification (page 53).
Note:
Figure 12: Single-Ended Input Signal Levels
1,150mV
VIH(AC)
1,025mV
VIH(DC)
936mV
918mV
900mV
882mV
864mV
VREF + AC noise
VREF + DC error
VREF - DC error
VREF - AC noise
775mV
VIL(DC)
650mV
VIL(AC)
1. Numbers in diagram reflect nominal DDR2-400/DDR2-533 values.
Note:
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
43
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Input Electrical Characteristics and Operating Conditions
Table 16: Differential Input Logic Levels
All voltages referenced to VSS
Parameter
Symbol
VIN(DC)
VID(DC)
VID(AC)
VIX(AC)
VMP(DC)
Min
Max
VDDQ
Units Notes
DC input signal voltage
–300
mV
mV
mV
mV
mV
1, 6
2, 6
3, 6
4
DC differential input voltage
AC differential input voltage
AC differential cross-point voltage
Input midpoint voltage
250
500
VDDQ
VDDQ
0.50 × VDDQ - 175
850
0.50 × VDDQ + 175
950
5
1. VIN(DC) specifies the allowable DC execution of each input of differential pair such as CK,
CK#, DQS, DQS#, LDQS, LDQS#, UDQS, UDQS#, and RDQS, RDQS#.
Notes:
2. VID(DC) specifies the input differential voltage |VTR - VCP| required for switching, where
VTR is the true input (such as CK, DQS, LDQS, UDQS) level and VCP is the complementary
input (such as CK#, DQS#, LDQS#, UDQS#) level. The minimum value is equal to VIH(DC)
VIL(DC). Differential input signal levels are shown in Figure 13.
-
3. VID(AC) specifies the input differential voltage |VTR - VCP| required for switching, where
VTR is the true input (such as CK, DQS, LDQS, UDQS, RDQS) level and VCP is the comple-
mentary input (such as CK#, DQS#, LDQS#, UDQS#, RDQS#) level. The minimum value is
equal to VIH(AC) - VIL(AC), as shown in Table 15 (page 43).
4. The typical value of VIX(AC) is expected to be about 0.5 × VDDQ of the transmitting device
and VIX(AC) is expected to track variations in VDDQ. VIX(AC) indicates the voltage at which
differential input signals must cross, as shown in Figure 13.
5. VMP(DC) specifies the input differential common mode voltage (VTR + VCP)/2 where VTR is
the true input (CK, DQS) level and VCP is the complementary input (CK#, DQS#). VMP(DC)
is expected to be approximately 0.5 × VDDQ
.
6. VDDQ + 300mV allowed provided 1.9V is not exceeded.
Figure 13: Differential Input Signal Levels
1
2.1V
VIN(DC)max
VDDQ = 1.8V
2
CP
1.075V
0.9V
X
5
4
3
VID(DC)
VIX(AC)
VMP(DC)
6
VID(AC)
0.725V
X
2
TR
1
VIN(DC)min
–0.30V
1. TR and CP may not be more positive than VDDQ + 0.3V or more negative than VSS - 0.3V.
Notes:
2. TR represents the CK, DQS, RDQS, LDQS, and UDQS signals; CP represents CK#, DQS#,
RDQS#, LDQS#, and UDQS# signals.
3. This provides a minimum of 850mV to a maximum of 950mV and is expected to be
VDDQ/2.
4. TR and CP must cross in this region.
5. TR and CP must meet at least VID(DC)min when static and is centered around VMP(DC)
6. TR and CP must have a minimum 500mV peak-to-peak swing.
.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
44
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Input Electrical Characteristics and Operating Conditions
7. Numbers in diagram reflect nominal values (VDDQ = 1.8V).
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
45
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Output Electrical Characteristics and Operating Conditions
Output Electrical Characteristics and Operating Conditions
Table 17: Differential AC Output Parameters
Parameter
Symbol
VOX(AC)
Vswing
Min
0.50 × VDDQ - 125
1.0
Max
Units Notes
AC differential cross-point voltage
AC differential voltage swing
0.50 × VDDQ + 125
mV
mV
1
–
1. The typical value of VOX(AC) is expected to be about 0.5 × VDDQ of the transmitting de-
vice and VOX(AC) is expected to track variations in VDDQ. VOX(AC) indicates the voltage at
which differential output signals must cross.
Note:
Figure 14: Differential Output Signal Levels
VDDQ
VTR
Crossing point
VOX
Vswing
VCP
VSSQ
Table 18: Output DC Current Drive
Parameter
Symbol
IOH
IOL
Value
–13.4
13.4
Units
mA
Notes
1, 2, 4
2, 3, 4
Output MIN source DC current
Output MIN sink DC current
mA
1.
2.
Notes:
For IOH(DC); VDDQ = 1.7V, VOUT = 1,420mV. (VOUT - VDDQ)/IOH must be less than 21Ω for
values of VOUT between VDDQ and VDDQ - 280mV.
For IOL(DC); VDDQ = 1.7V, VOUT = 280mV. VOUT/IOL must be less than 21Ω for values of VOUT
between 0V and 280mV.
3. The DC value of VREF applied to the receiving device is set to VTT.
4. The values of IOH(DC) and IOL(DC) are based on the conditions given in Notes 1 and 2. They
are used to test device drive current capability to ensure VIH,min plus a noise margin and
VIL,max minus a noise margin are delivered to an SSTL_18 receiver. The actual current val-
ues are derived by shifting the desired driver operating point (see output IV curves)
along a 21Ω load line to define a convenient driver current for measurement.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
46
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Output Electrical Characteristics and Operating Conditions
Table 19: Output Characteristics
Parameter
Min
Nom
Max
Units
Ω
Notes
1, 2
Output impedance
Pull-up and pull-down mismatch
Output slew rate
See Output Driver Characteristics (page 48)
0
4
5
1, 2, 3
1, 4, 5, 6
–
–
Ω
1.5
V/ns
1.
Notes:
Absolute specifications: 0°C ≤ TC ≤ +85°C; VDDQ = +1.8V ±0.1V, VDD = +1.8V ±0.1V.
2. Impedance measurement conditions for output source DC current: VDDQ = 1.7V;
VOUT = 1420mV; (VOUT - VDDQ)/IOH must be less than 23.4Ω for values of VOUT between
VDDQ and VDDQ - 280mV. The impedance measurement condition for output sink DC cur-
rent: VDDQ = 1.7V; VOUT = 280mV; VOUT/IOL must be less than 23.4Ω for values of VOUT
between 0V and 280mV.
3. Mismatch is an absolute value between pull-up and pull-down; both are measured at
the same temperature and voltage.
4. Output slew rate for falling and rising edges is measured between VTT - 250mV and
VTT + 250mV for single-ended signals. For differential signals (DQS, DQS#), output slew
rate is measured between DQS - DQS# = –500mV and DQS# - DQS = +500mV. Output
slew rate is guaranteed by design but is not necessarily tested on each device.
5. The absolute value of the slew rate as measured from VIL(DC)max to VIH(DC)min is equal to
or greater than the slew rate as measured from VIL(AC)max to VIH(AC)min. This is guaran-
teed by design and characterization.
6. IT and AT devices require an additional 0.4 V/ns in the MAX limit when TC is between –
40°C and 0°C.
Figure 15: Output Slew Rate Load
V
= V
/2
25Ω
Reference
TT
DDQ
Output
(V
point
)
OUT
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
47
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Output Driver Characteristics
Output Driver Characteristics
Figure 16: Full Strength Pull-Down Characteristics
120
100
80
60
40
20
0
0.0
0.5
1.0
OUT (V)
1.5
V
Table 20: Full Strength Pull-Down Current (mA)
Voltage (V)
0.0
Min
0.00
Nom
0.00
Max
0.00
0.1
4.30
5.63
7.95
0.2
8.60
11.30
16.52
22.19
27.59
32.39
36.45
40.38
44.01
47.01
49.63
51.71
53.32
54.9
15.90
23.85
31.80
39.75
47.70
55.55
62.95
69.55
75.35
80.35
84.55
87.95
90.70
93.00
95.05
97.05
99.05
101.05
0.3
12.90
16.90
20.40
23.28
25.44
26.79
27.67
28.38
28.96
29.46
29.90
30.29
30.65
30.98
31.31
31.64
31.96
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
56.03
57.07
58.16
59.27
60.35
1.6
1.7
1.8
1.9
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
48
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Output Driver Characteristics
Figure 17: Full Strength Pull-Up Characteristics
0
–20
–40
–60
–80
–100
–120
0
0.5
1.0
1.5
VDDQ - VOUT (V)
Table 21: Full Strength Pull-Up Current (mA)
Voltage (V)
0.0
Min
Nom
0.00
Max
0.00
0.00
0.1
–4.30
–5.63
–7.95
0.2
–8.60
–11.30
–16.52
–22.19
–27.59
–32.39
–36.45
–40.38
–44.01
–47.01
–49.63
–51.71
–53.32
–54.90
–56.03
–57.07
–58.16
–59.27
–60.35
–15.90
–23.85
–31.80
–39.75
–47.70
–55.55
–62.95
–69.55
–75.35
–80.35
–84.55
–87.95
–90.70
–93.00
–95.05
–97.05
–99.05
–101.05
0.3
–12.90
–16.90
–20.40
–23.28
–25.44
–26.79
–27.67
–28.38
–28.96
–29.46
–29.90
–30.29
–30.65
–30.98
–31.31
–31.64
–31.96
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
49
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Output Driver Characteristics
Figure 18: Reduced Strength Pull-Down Characteristics
70
60
50
40
30
20
10
0
0.0
0.5
1.0
OUT (V)
1.5
V
Table 22: Reduced Strength Pull-Down Current (mA)
Voltage (V)
0.0
Min
0.00
Nom
0.00
Max
0.00
0.1
1.72
2.98
4.77
0.2
3.44
5.99
9.54
0.3
5.16
8.75
14.31
19.08
23.85
28.62
33.33
37.77
41.73
45.21
48.21
50.73
52.77
54.42
55.80
57.03
58.23
59.43
60.63
0.4
6.76
11.76
14.62
17.17
19.32
21.40
23.32
24.92
26.30
27.41
28.26
29.10
29.70
30.25
30.82
31.41
31.98
0.5
8.16
0.6
9.31
0.7
10.18
10.72
11.07
11.35
11.58
11.78
11.96
12.12
12.26
12.39
12.52
12.66
12.78
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
50
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Output Driver Characteristics
Figure 19: Reduced Strength Pull-Up Characteristics
0
–10
–20
–30
–40
–50
–60
–70
0.0
0.5
1.0
1.5
VDDQ - VOUT (V)
Table 23: Reduced Strength Pull-Up Current (mA)
Voltage (V)
0.0
Min
Nom
0.00
Max
0.00
0.00
0.1
–1.72
–2.98
–4.77
0.2
–3.44
–5.99
–9.54
0.3
–5.16
–8.75
–14.31
–19.08
–23.85
–28.62
–33.33
–37.77
–41.73
–45.21
–48.21
–50.73
–52.77
–54.42
–55.8
0.4
–6.76
–11.76
–14.62
–17.17
–19.32
–21.40
–23.32
–24.92
–26.30
–27.41
–28.26
–29.10
–29.69
–30.25
–30.82
–31.42
–31.98
0.5
–8.16
0.6
–9.31
0.7
–10.18
–10.72
–11.07
–11.35
–11.58
–11.78
–11.96
–12.12
–12.26
–12.39
–12.52
–12.66
–12.78
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
–57.03
–58.23
–59.43
–60.63
1.7
1.8
1.9
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
51
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Power and Ground Clamp Characteristics
Power and Ground Clamp Characteristics
Power and ground clamps are provided on the following input-only balls: Address balls,
bank address balls, CS#, RAS#, CAS#, WE#, ODT, and CKE.
Table 24: Input Clamp Characteristics
Minimum Power Clamp Current
(mA)
Minimum Ground Clamp Current
(mA)
Voltage Across Clamp (V)
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.1
0.1
1.0
1.0
2.5
2.5
4.7
4.7
6.8
6.8
9.1
9.1
11.0
13.5
16.0
18.2
21.0
11.0
13.5
16.0
18.2
21.0
Figure 20: Input Clamp Characteristics
25
20
15
10
5
0
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8
Voltage Across Clamp (V)
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2004 Micron Technology, Inc. All rights reserved.
52
1Gb: x4, x8, x16 DDR2 SDRAM
AC Overshoot/Undershoot Specification
AC Overshoot/Undershoot Specification
Some revisions will support the 0.9V maximum average amplitude instead of the 0.5V
maximum average amplitude shown in Table 25 and Table 26.
Table 25: Address and Control Balls
Applies to address balls, bank address balls, CS#, RAS#, CAS#, WE#, CKE, and ODT
Specification
-3/-3E
Parameter
-187E
-25/-25E
-37E
-5E
Maximum peak amplitude allowed for overshoot area
(see Figure 21)
0.50V
0.50V
0.50V
0.50V
0.50V
0.50V
Maximum peak amplitude allowed for undershoot area
(see Figure 22)
0.50V
0.50V
0.50V
0.50V
Maximum overshoot area above VDD (see Figure 21)
Maximum undershoot area below VSS (see Figure 22)
0.5 Vns
0.5 Vns
0.66 Vns
0.66 Vns
0.80 Vns 1.00 Vns 1.33 Vns
0.80 Vns 1.00 Vns 1.33 Vns
Table 26: Clock, Data, Strobe, and Mask Balls
Applies to DQ, DQS, DQS#, RDQS, RDQS#, UDQS, UDQS#, LDQS, LDQS#, DM, UDM, and LDM
Specification
-3/-3E
Parameter
-187E
-25/-25E
-37E
-5E
Maximum peak amplitude allowed for overshoot area
(see Figure 21)
0.50V
0.50V
0.50V
0.50V
0.50V
Maximum peak amplitude allowed for undershoot area
(see Figure 22)
0.50V
0.50V
0.50V
0.50V
0.50V
Maximum overshoot area above VDDQ (see Figure 21)
Maximum undershoot area below VSSQ (see Figure 22)
0.19 Vns
0.19 Vns
0.23 Vns
0.23 Vns
0.23 Vns
0.23 Vns
0.28 Vns 0.38 Vns
0.28 Vns 0.38 Vns
Figure 21: Overshoot
Maximum amplitude
Overshoot area
VDD/VDDQ
VSS/VSSQ
Time (ns)
Figure 22: Undershoot
VSS/VSSQ
Undershoot area
Maximum amplitude
Time (ns)
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
53
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
AC Overshoot/Undershoot Specification
Table 27: AC Input Test Conditions
Parameter
Symbol
Min
Max
Units
Notes
Input setup timing measurement reference level address
balls, bank address balls, CS#, RAS#, CAS#, WE#, ODT,
DM, UDM, LDM, and CKE
VRS
See Note 2
1, 2, 3, 4
Input hold timing measurement reference level address
balls, bank address balls, CS#, RAS#, CAS#, WE#, ODT,
DM, UDM, LDM, and CKE
VRH
See Note 5
1, 3, 4, 5
Input timing measurement reference level (single-ended)
DQS for x4, x8; UDQS, LDQS for x16
VREF(DC)
VRD
VDDQ × 0.49 VDDQ × 0.51
VIX(AC)
V
V
1, 3, 4, 6
Input timing measurement reference level (differential)
CK, CK# for x4, x8, x16; DQS, DQS# for x4, x8; RDQS,
RDQS# for x8; UDQS, UDQS#, LDQS, LDQS# for x16
1, 3, 7, 8, 9
1. All voltages referenced to VSS.
Notes:
2. Input waveform setup timing (tISb) is referenced from the input signal crossing at the
VIH(AC) level for a rising signal and VIL(AC) for a falling signal applied to the device under
test, as shown in Figure 31 (page 66).
3. See Input Slew Rate Derating (page 55).
4. The slew rate for single-ended inputs is measured from DC level to AC level, VIL(DC) to
VIH(AC) on the rising edge and VIL(AC) to VIH(DC) on the falling edge. For signals referenced
to VREF, the valid intersection is where the “tangent” line intersects VREF, as shown in
Figure 24 (page 58), Figure 26 (page 59), Figure 28 (page 64), and Figure 30
(page 65).
5. Input waveform hold (tIHb) timing is referenced from the input signal crossing at the
VIL(DC) level for a rising signal and VIH(DC) for a falling signal applied to the device under
test, as shown in Figure 31 (page 66).
6. Input waveform setup timing (tDS) and hold timing (tDH) for single-ended data strobe is
referenced from the crossing of DQS, UDQS, or LDQS through the Vref level applied to
the device under test, as shown in Figure 33 (page 67).
7. Input waveform setup timing (tDS) and hold timing (tDH) when differential data strobe
is enabled is referenced from the cross-point of DQS/DQS#, UDQS/UDQS#, or LDQS/
LDQS#, as shown in Figure 32 (page 66).
8. Input waveform timing is referenced to the crossing point level (VIX) of two input signals
(VTR and VCP) applied to the device under test, where VTR is the true input signal and VCP
is the complementary input signal, as shown in Figure 34 (page 67).
9. The slew rate for differentially ended inputs is measured from twice the DC level to
twice the AC level: 2 × VIL(DC) to 2 × VIH(AC) on the rising edge and 2 × VIL(AC) to 2 ×
VIH(DC) on the falling edge. For example, the CK/CK# would be –250mV to +500mV for
CK rising edge and would be +250mV to –500mV for CK falling edge.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
54
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Input Slew Rate Derating
Input Slew Rate Derating
For all input signals, the total tIS (setup time) and tIH (hold time) required is calculated
by adding the data sheet tIS (base) and tIH (base) value to the ΔtIS and ΔtIH derating
value, respectively. Example: tIS (total setup time) = tIS (base) + ΔtIS.
tIS, the nominal slew rate for a rising signal, is defined as the slew rate between the last
crossing of VREF(DC) and the first crossing of VIH(AC)min. Setup nominal slew rate (tIS) for
a falling signal is defined as the slew rate between the last crossing of VREF(DC) and the
first crossing of VIL(AC)max
.
If the actual signal is always earlier than the nominal slew rate line between shaded
“VREF(DC) to AC region,” use the nominal slew rate for the derating value (Figure 23
(page 58)).
If the actual signal is later than the nominal slew rate line anywhere between the sha-
ded “VREF(DC) to AC region,” the slew rate of a tangent line to the actual signal from the
AC level to DC level is used for the derating value (see Figure 24 (page 58)).
tIH, the nominal slew rate for a rising signal, is defined as the slew rate between the last
crossing of VIL(DC)max and the first crossing of VREF(DC). tIH, nominal slew rate for a fall-
ing signal, is defined as the slew rate between the last crossing of VIH(DC)min and the first
crossing of VREF(DC)
.
If the actual signal is always later than the nominal slew rate line between shaded “DC
to VREF(DC) region,” use the nominal slew rate for the derating value (Figure 25
(page 59)).
If the actual signal is earlier than the nominal slew rate line anywhere between shaded
“DC to VREF(DC) region,” the slew rate of a tangent line to the actual signal from the DC
level to VREF(DC) level is used for the derating value (Figure 26 (page 59)).
Although the total setup time might be negative for slow slew rates (a valid input signal
will not have reached VIH[AC]/VIL[AC] at the time of the rising clock transition), a valid
input signal is still required to complete the transition and reach VIH(AC)/VIL(AC)
.
For slew rates in between the values listed in Table 28 (page 56) and Table 29
(page 57), the derating values may obtained by linear interpolation.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
55
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Input Slew Rate Derating
Table 28: DDR2-400/533 Setup and Hold Time Derating Values (tIS and tIH)
CK, CK# Differential Slew Rate
2.0 V/ns 1.5 V/ns 1.0 V/ns
Command/Address Slew Rate (V/ns)
ΔtIS
ΔtIH
+94
ΔtIS
ΔtIH
+124
+119
+113
+105
+75
ΔtIS
ΔtIH
+154
+149
+143
+135
+105
+81
Units
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.25
0.2
0.15
0.1
+187
+179
+167
+150
+125
+83
+217
+209
+197
+180
+155
+113
+30
+247
+239
+227
+210
+185
+143
+60
+89
+83
+75
+45
+21
+51
0
0
+30
+60
–11
–14
+19
+16
+49
+46
–25
–31
+5
–1
+35
+29
–43
–54
–13
–24
+17
+6
–67
–83
–37
–53
–7
–23
–110
–175
–285
–350
–525
–800
–1,450
–125
–188
–292
–375
–500
–708
–1,125
–80
–95
–50
–65
–145
–255
–320
–495
–770
–1,420
–158
–262
–345
–470
–678
–1,095
–115
–225
–290
–465
–740
–1,390
–128
–232
–315
–440
–648
–1,065
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
56
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Input Slew Rate Derating
Table 29: DDR2-667/800/1066 Setup and Hold Time Derating Values (tIS and tIH)
Command/
Address Slew
Rate (V/ns)
CK, CK# Differential Slew Rate
1.5 V/ns
2.0 V/ns
1.0 V/ns
ΔtIS
+150
+143
+133
+120
+100
+67
ΔtIH
+94
+89
+83
+75
+45
+21
0
ΔtIS
+180
+173
+163
+150
+160
+97
ΔtIH
+124
+119
+113
+105
+75
ΔtIS
+210
+203
+193
+180
+160
+127
+60
ΔtIH
+154
+149
+143
+135
+105
+81
Units
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.25
0.2
0.15
0.1
+51
0
+30
+30
+60
–5
–14
+25
+16
+55
+46
–13
–31
+17
–1
+47
+29
–22
–54
+8
–24
+38
+6
–34
–83
–4
–53
+36
–23
–60
–125
–188
–292
–375
–500
–708
–30
–95
0
–65
–100
–168
–200
–325
–517
–1,000
–70
–158
–262
–345
–470
–678
–1,095
–40
–128
–232
–315
–440
–648
–1,065
–138
–170
–295
–487
–970
–108
–140
–265
–457
–940
–1,125
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
57
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Input Slew Rate Derating
Figure 23: Nominal Slew Rate for tIS
CK
CK#
t
t
t
t
IH
IH
IS
IS
V
DDQ
V
IH(AC)min
V
to AC
region
REF
V
IH(DC)min
Nominal
slew rate
V
REF(DC)
Nominal
slew rate
V
V
IL(DC)max
VREF to AC
region
IL(AC)max
V
SS
ΔTF
ΔTR
V
(DC) - V
IL(AC)max
V
- V
Setup slew rate
rising signal
REF
Setup slew rate
falling signal
IH(AC)min REF(DC)
=
=
ΔTF
Δ
TR
Figure 24: Tangent Line for tIS
CK
CK#
t
t
t
t
IH
IH
IS
IS
V
DDQ
V
V
IH(AC)min
V
to AC
region
REF
Nominal
line
IH(DC)min
Tangent
line
V
REF(DC)
Tangent
line
V
V
IL(DC)max
Nominal
line
V
to AC
region
REF
IL(AC)max
ΔTF
ΔTR
V
SS
Tangent line (V
- V
)
Setup slew rate
rising signal
IH[AC]min
REF[DC]
=
ΔTR
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
58
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Input Slew Rate Derating
Figure 25: Nominal Slew Rate for tIH
CK
CK#
t
t
t
t
IS
IH
IH
IS
VDDQ
VIH(AC)min
VIH(DC)min
DC to V
REF
region
Nominal
slew rate
VREF(DC)
Nominal
slew rate
DC to V
region
REF
VIL(DC)max
VIL(AC)max
VSS
ΔTF
ΔTR
Figure 26: Tangent Line for tIH
CK
CK#
t
t
t
t
IS
IH
IH
IS
V
DDQ
V
IH(AC)min
Nominal
line
V
IH(DC)min
DC to V
REF
region
Tangent
line
V
REF(DC)
Tangent
line
Nominal
line
DC to V
region
REF
V
IL(DC)max
V
IL(AC)max
V
SS
ΔTR
ΔTF
Tangent line (V
- V
)
Tangent line (V
- V
)
REF[DC]
Hold slew rate
rising signal
Hold slew rate
falling signal
REF[DC]
IL[DC]max
IH[DC]min
=
=
ΔTR
ΔTF
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
59
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Input Slew Rate Derating
Table 30: DDR2-400/533 tDS, tDH Derating Values with Differential Strobe
All units are shown in picoseconds
DQS, DQS# Differential Slew Rate
1.8 V/ns 1.6 V/ns 1.4 V/ns
DQ
Slew
Rate
4.0 V/ns
3.0 V/ns
2.0 V/ns
1.2 V/ns
1.0 V/ns
0.8 V/ns
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
(V/ns) tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH
2.0
1.5
1.0
0.9
0.8
0.7
0.6
0.5
0.4
125
83
0
45
21
0
125
83
0
45
21
0
125
83
0
45
21
0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
–
–
95
12
1
33
12
–2
–
–
24
13
–1
24
10
–7
–
–
–
–
–
–
–
–11 –14 –11 –14
25
11
–7
22
5
–
–
–
–
–
–
–
–25 –31 –13 –19
23
5
17
–6
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–31 –42 –19 –30
–18
17
–7
6
–
–
–
–
–
–
–
–
–
–
–
–43 –59 –31 –47 –19 –35
–23
–11
–
–
–
–
–
–
–
–
–74 –89 –62 –77 –50 –65 –38 –53
–127 –140 –115 –128 –103 –116
–
–
–
–
–
–
–
–
–
–
1. For all input signals, the total tDS and tDH required is calculated by adding the data
sheet value to the derating value listed in Table 30.
Notes:
2. tDS nominal slew rate for a rising signal is defined as the slew rate between the last
crossing of VREF(DC) and the first crossing of VIH(AC)min. tDS nominal slew rate for a falling
signal is defined as the slew rate between the last crossing of VREF(DC) and the first cross-
ing of VIL(AC)max. If the actual signal is always earlier than the nominal slew rate line
between the shaded “VREF(DC) to AC region,” use the nominal slew rate for the derating
value (see Figure 27 (page 64)). If the actual signal is later than the nominal slew rate
line anywhere between the shaded “VREF(DC) to AC region,” the slew rate of a tangent
line to the actual signal from the AC level to DC level is used for the derating value (see
Figure 28 (page 64)).
3. tDH nominal slew rate for a rising signal is defined as the slew rate between the last
crossing of VIL(DC)max and the first crossing of VREF(DC). tDH nominal slew rate for a falling
signal is defined as the slew rate between the last crossing of VIH(DC)min and the first cross-
ing of VREF(DC). If the actual signal is always later than the nominal slew rate line
between the shaded “DC level to VREF(DC) region,” use the nominal slew rate for the de-
rating value (see Figure 29 (page 65)). If the actual signal is earlier than the nominal
slew rate line anywhere between shaded “DC to VREF(DC) region,” the slew rate of a tan-
gent line to the actual signal from the DC level to VREF(DC) level is used for the derating
value (see Figure 30 (page 65)).
4. Although the total setup time might be negative for slow slew rates (a valid input signal
will not have reached VIH[AC]/VIL[AC] at the time of the rising clock transition), a valid in-
put signal is still required to complete the transition and reach VIH(AC)/VIL(AC)
.
5. For slew rates between the values listed in this table, the derating values may be ob-
tained by linear interpolation.
6. These values are typically not subject to production test. They are verified by design and
characterization.
7. Single-ended DQS requires special derating. The values in Table 32 (page 62) are the
DQS single-ended slew rate derating with DQS referenced at VREF and DQ referenced at
the logic levels tDSb and tDHb. Converting the derated base values from DQ referenced
to the AC/DC trip points to DQ referenced to VREF is listed in Table 34 (page 63) and
Table 35 (page 63). Table 34 provides the VREF-based fully derated values for the DQ
(tDSa and tDHa) for DDR2-533. Table 35 provides the VREF-based fully derated values for
the DQ (tDSa and tDHa) for DDR2-400.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
60
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Input Slew Rate Derating
Table 31: DDR2-667/800/1066 tDS, tDH Derating Values with Differential Strobe
All units are shown in picoseconds
DQS, DQS# Differential Slew Rate
1.8 V/ns 1.6 V/ns 1.4 V/ns
DQ
Slew
Rate
2.8 V/ns
2.4 V/ns
2.0 V/ns
1.2 V/ns
1.0 V/ns
0.8 V/ns
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
Δ
(V/ns) tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH
2.0
1.5
1.0
0.9
0.8
0.7
0.6
0.5
100
67
0
63
42
0
100
67
0
63
42
0
100
67
0
63
42
0
112
79
12
7
75
54
124
91
24
19
11
2
87
66
136
103
36
31
23
14
2
99
78
36
22
5
148 111 160 123 172 135
115
48
43
35
26
14
90
48
127 102 139 114
12
24
60
55
47
38
26
0
60
46
72
67
59
50
38
12
72
58
–5
–14
–5
–14
–5
–14
–2
10
34
–13 –31 –13 –31 –13 –31
–1
–19
–7
17
29
41
–22 –54 –22 –54 –22 –54 –10 –42
–30
–18
–47
–6
6
18
–34 –83 –34 –83 –34 –83 –22 –71 –10 –59
–35
–23
–65
–11
–53
–60 –125 –60 –125 –60 –125 –48 –113 –36 –101 –24 –89 –12 –77
0.4 –100 –188 –100 –188 –100 –188 –88 –176 –76 –164 –64 –152 –52 –140 –40 –128 –28 –116
1. For all input signals the total tDS and tDH required is calculated by adding the data
Notes:
sheet value to the derating value listed in Table 31.
2. tDS nominal slew rate for a rising signal is defined as the slew rate between the last
crossing of VREF(DC) and the first crossing of VIH(AC)min. tDS nominal slew rate for a falling
signal is defined as the slew rate between the last crossing of VREF(DC) and the first cross-
ing of VIL(AC)max. If the actual signal is always earlier than the nominal slew rate line
between the shaded “VREF(DC) to AC region,” use the nominal slew rate for the derating
value (see Figure 27 (page 64)). If the actual signal is later than the nominal slew rate
line anywhere between shaded “VREF(DC) to AC region,” the slew rate of a tangent line
to the actual signal from the AC level to DC level is used for the derating value (see Fig-
ure 28 (page 64)).
3. tDH nominal slew rate for a rising signal is defined as the slew rate between the last
crossing of VIL(DC)max and the first crossing of VREF(DC). tDH nominal slew rate for a falling
signal is defined as the slew rate between the last crossing of VIH(DC)min and the first cross-
ing of VREF(DC). If the actual signal is always later than the nominal slew rate line
between the shaded “DC level to VREF(DC) region,” use the nominal slew rate for the de-
rating value (see Figure 29 (page 65)). If the actual signal is earlier than the nominal
slew rate line anywhere between the shaded “DC to VREF(DC) region,” the slew rate of a
tangent line to the actual signal from the DC level to VREF(DC) level is used for the derat-
ing value (see Figure 30 (page 65)).
4. Although the total setup time might be negative for slow slew rates (a valid input signal
will not have reached VIH[AC]/VIL[AC] at the time of the rising clock transition), a valid in-
put signal is still required to complete the transition and reach VIH(AC)/VIL(AC)
.
5. For slew rates between the values listed in this table, the derating values may be ob-
tained by linear interpolation.
6. These values are typically not subject to production test. They are verified by design and
characterization.
7. Single-ended DQS requires special derating. The values in Table 32 (page 62) are the
DQS single-ended slew rate derating with DQS referenced at VREF and DQ referenced at
the logic levels tDSb and tDHb. Converting the derated base values from DQ referenced
to the AC/DC trip points to DQ referenced to VREF is listed in Table 33 (page 62). Ta-
ble 33 provides the VREF-based fully derated values for the DQ (tDSa and tDHa) for
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
61
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Input Slew Rate Derating
DDR2-667. It is not advised to operate DDR2-800 and DDR2-1066 devices with single-
ended DQS; however, Table 32 would be used with the base values.
Table 32: Single-Ended DQS Slew Rate Derating Values Using tDSb and tDHb
Reference points indicated in bold; Derating values are to be used with base tDSb- and tDHb--specified values
DQS Single-Ended Slew Rate Derated (at VREF
1.6 V/ns 1.4 V/ns 1.2 V/ns 1.0 V/ns 0.8 V/ns
)
2.0 V/ns
1.8 V/ns
0.6 V/ns
0.4 V/ns
DQ (V/ns)
tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH
2.0
1.5
1.0
130 53 130 53 130 53 130 53 130 53 145 48 155 45 165 41 175 38
97
32
97
32
97
32
97
32
97
32 112 27 122 24 132 20 142 17
30 –10 30 –10 30 –10 30 –10 30 –10
25 –24 25 –24 25 –24 25 –24 25 –24
55 –18 65 –22 75 –25
50 –32 60 –36 70 –39
45 –15
0.9
0.8
0.7
0.6
0.5
0.4
40 –29
17 –41 17 –41 17 –41 17 –41 17 –41 32 –46 42 –49 52 –53 61 –56
5
–64
5
–64
5
–64
5
–64
5
–64 20 –69 30 –72 40 –75 50 –79
–93 –98 18 –102 28 –105 38 –108
–147 17 –150
–78 –198 –78 –198 –78 –198 –78 –198 –78 –198 –63 –203 –53 –206 –43 –210 –33 –213
–7
–93
–7
–93
–7
–93
–7
–93
–7
8
–28 –135 –28 –135 –28 –135 –28 –135 –28 –135 –13 –140 –3 –143
7
Table 33: Single-Ended DQS Slew Rate Fully Derated (DQS, DQ at VREF) at DDR2-667
Reference points indicated in bold
DQS Single-Ended Slew Rate Derated (at VREF
1.6 V/ns 1.4 V/ns 1.2 V/ns 1.0 V/ns 0.8 V/ns
DQ (V/ns) tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH
)
2.0 V/ns
1.8 V/ns
0.6 V/ns
0.4 V/ns
2.0
1.5
1.0
330 291 330 291 330 291 330 291 330 291 345 286 355 282 365 29 375 276
330 290 330 290 330 290 330 290 330 290 345 285 355 282 365 279 375 275
330 290 330 290 330 290 330 290 330 290
347 290 347 290 347 290 347 290 347 290
355 282 365 278 375 275
372 282 382 278 392 275
345 285
0.9
0.8
0.7
0.6
0.5
0.4
362 285
367 290 367 290 367 290 367 290 367 290 382 285 392 282 402 278 412 275
391 290 391 290 391 290 391 290 391 290 406 285 416 281 426 278 436 275
426 290 426 290 426 290 426 290 426 290 441 285 451 282 461 278 471 275
472 290 472 290 472 290 472 290 472 290 487 285 497 282 507 278 517 275
522 289 522 289 522 289 522 289 522 289 537 284 547 281 557 278 567 274
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
62
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Input Slew Rate Derating
Table 34: Single-Ended DQS Slew Rate Fully Derated (DQS, DQ at VREF) at DDR2-533
Reference points indicated in bold
DQS Single-Ended Slew Rate Derated (at VREF
1.6 V/ns 1.4 V/ns 1.2 V/ns 1.0 V/ns 0.8 V/ns
DQ (V/ns) tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH
)
2.0 V/ns
1.8 V/ns
0.6 V/ns
0.4 V/ns
2.0
1.5
1.0
355 341 355 341 355 341 355 341 355 341 370 336 380 332 390 329 400 326
364 340 364 340 364 340 364 340 364 340 379 335 389 332 399 329 409 325
380 340 380 340 380 340 380 340 380 340
402 340 402 340 402 340 402 340 402 340
405 332 415 328 425 325
427 332 437 328 447 325
395 335
0.9
0.8
0.7
0.6
0.5
0.4
417 335
429 340 429 340 429 340 429 340 429 340 444 335 454 332 464 328 474 325
463 340 463 340 463 340 463 340 463 340 478 335 488 331 498 328 508 325
510 340 510 340 510 340 510 340 510 340 525 335 535 332 545 328 555 325
572 340 572 340 572 340 572 340 572 340 587 335 597 332 607 328 617 325
647 339 647 339 647 339 647 339 647 339 662 334 672 331 682 328 692 324
Table 35: Single-Ended DQS Slew Rate Fully Derated (DQS, DQ at VREF) at DDR2-400
Reference points indicated in bold
DQS Single-Ended Slew Rate Derated (at VREF
1.6 V/ns 1.4 V/ns 1.2 V/ns 1.0 V/ns 0.8 V/ns
DQ (V/ns) tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH
)
2.0 V/ns
1.8 V/ns
0.6 V/ns
0.4 V/ns
2.0
1.5
1.0
405 391 405 391 405 391 405 391 405 391 420 386 430 382 440 379 450 376
414 390 414 390 414 390 414 390 414 390 429 385 439 382 449 379 459 375
430 390 430 390 430 390 430 390 430 390
452 390 452 390 452 390 452 390 452 390
455 382 465 378 475 375
477 382 487 378 497 375
445 385
0.9
0.8
0.7
0.6
0.5
0.4
467 385
479 390 479 390 479 390 479 390 479 390 494 385 504 382 514 378 524 375
513 390 513 390 513 390 513 390 513 390 528 385 538 381 548 378 558 375
560 390 560 390 560 390 560 390 560 390 575 385 585 382 595 378 605 375
622 390 622 390 622 390 622 390 622 390 637 385 647 382 657 378 667 375
697 389 697 389 697 389 697 389 697 389 712 384 722 381 732 378 742 374
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
63
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Input Slew Rate Derating
Figure 27: Nominal Slew Rate for tDS
1
DQS
1
DQS#
t
t
t
DS
t
DH
DH
DS
VDDQ
VIH(AC)min
V
to AC
region
REF
VIH(DC)min
Nominal
slew rate
VREF(DC)
Nominal
slew rate
VIL(DC)max
V
to AC
region
REF
VIL(AC)max
VSS
ΔTF
ΔTR
V
REF(DC) - VIL(AC)max
VIH(AC)min
-
VREF(DC)
Setup slew rate
falling signal
Setup slew rate
rising signal
=
=
ΔTF
ΔTR
1. DQS, DQS# signals must be monotonic between VIL(DC)max and VIH(DC)min
.
Note:
Figure 28: Tangent Line for tDS
1
DQS
1
DQS#
t
t
t
DS
t
DS
DH
DH
V
DDQ
V
V
IH(AC)min
Nominal
line
V
to AC
REF
region
IH(DC)min
Tangent line
V
REF(DC)
Tangent line
V
V
IL(DC)max
IL(AC)max
Nominal line
V
to AC
region
REF
ΔTR
ΔTF
V
SS
Tangent line (V
- V )
IL[AC]max
Tangent line (V
- V )
REF[DC]
REF[DC]
IH[AC]min
Setup slew rate
falling signal
Setup slew rate
rising signal
=
=
ΔTF
ΔTR
1. DQS, DQS# signals must be monotonic between VIL(DC)max and VIH(DC)min
.
Note:
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
64
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Input Slew Rate Derating
Figure 29: Nominal Slew Rate for tDH
1
DQS
1
DQS#
t
t
t
t
IS
IH
IH
IS
VDDQ
VIH(AC)min
VIH(DC)min
DC to V
REF
region
Nominal
slew rate
VREF(DC)
Nominal
slew rate
DC to V
region
REF
VIL(DC)max
VIL(AC)max
VSS
ΔTF
ΔTR
Hold slew rate
VREF(DC)
-
Δ
VIL(DC)max
TR
VIH(DC)min
-
VREF(DC)
Hold slew rate
rising signal
=
=
falling signal
Δ
TF
1. DQS, DQS# signals must be monotonic between VIL(DC)max and VIH(DC)min
.
Note:
Figure 30: Tangent Line for tDH
1
DQS
1
DQS#
t
t
t
t
IS
IH
IH
IS
VDDQ
VIH(AC)min
Nominal
line
VIH(DC)min
DC to V
REF
region
Tangent
line
VREF(DC)
Tangent
line
DC to V
region
REF
Nominal
line
VIL(DC)max
VIL(AC)max
VSS
ΔTF
ΔTR
Tangent line (V
- V
)
Tangent line (V
- V
)
REF[DC]
REF[DC]
IL[DC]max
IH[DC]min
Hold slew rate
rising signal
Hold slew rate
falling signal
=
=
ΔTR
ΔTF
1. DQS, DQS# signals must be monotonic between VIL(DC)max and VIH(DC)min
.
Note:
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
65
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Input Slew Rate Derating
Figure 31: AC Input Test Signal Waveform Command/Address Balls
CK#
CK
t
t
t
t
IH
IS
IH
b
IS
b
b
b
Logic levels
VDDQ
VIH(AC)min
VIH(DC)min
VREF(DC)
VIL(DC)min
VIL(AC)min
VSSQ
VREF levels
t
t
IH
t
t
IH
IS
a
IS
a
a
a
Figure 32: AC Input Test Signal Waveform for Data with DQS, DQS# (Differential)
DQS#
DQS
t
t
t
t
DH
DS
DH
DS
b
b
b
b
Logic levels
VDDQ
VIH(AC)min
VIH(DC)min
VREF(DC)
VIL(DC)max
VIL(AC)max
VSSQ
VREF levels
t
t
t
DS
a
t
DH
a
DS
DH
a
a
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
66
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Input Slew Rate Derating
Figure 33: AC Input Test Signal Waveform for Data with DQS (Single-Ended)
VREF
DQS
t
t
t
t
DH
DS
DH
DS
b
b
b
b
Logic levels
VDDQ
VIH(AC)min
VIH(DC)min
VREF(DC)
VIL(DC)max
VIL(AC)max
VSSQ
VREF levels
t
t
t
DS
a
t
DH
a
DS
DH
a
a
Figure 34: AC Input Test Signal Waveform (Differential)
VDDQ
VTR
Crossing point
Vswing
VIX
VCP
VSSQ
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
67
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Commands
Commands
Truth Tables
The following tables provide a quick reference of available DDR2 SDRAM commands,
including CKE power-down modes and bank-to-bank commands.
Table 36: Truth Table – DDR2 Commands
Notes: 1–3 apply to the entire table
CKE
Previous Current
BA2–
Function
Cycle
Cycle
CS# RAS# CAS# WE#
BA0 An–A11 A10 A9–A0 Notes
LOAD MODE
REFRESH
H
H
H
L
H
H
L
L
L
L
L
L
L
L
H
H
X
H
L
BA
X
OP code
4, 6
X
X
X
X
X
X
X
X
X
SELF REFRESH entry
SELF REFRESH exit
L
L
L
X
H
H
L
X
H
L
X
H
H
X
4, 7
6
Single bank
PRECHARGE
H
H
L
BA
X
X
L
X
X
All banks PRECHARGE
Bank ACTIVATE
WRITE
H
H
H
H
H
H
L
L
L
L
L
H
H
L
L
H
L
X
H
BA
BA
Row address
4
H
Column
address
L
H
L
Column 4, 5, 6,
address
Column 4, 5, 6,
address
Column 4, 5, 6,
address
Column 4, 5, 6,
8
WRITE with auto
precharge
H
H
H
H
H
H
L
L
L
H
H
H
L
L
L
L
BA
BA
BA
Column
address
8
READ
H
H
Column
address
8
READ with auto
precharge
Column
address
H
address
8
NO OPERATION
Device DESELECT
Power-down entry
H
H
H
X
X
L
L
H
H
L
H
X
X
H
X
H
H
X
X
H
X
H
H
X
X
H
X
H
X
X
X
X
X
X
X
X
X
X
X
X
9
9
Power-down exit
L
H
H
L
X
X
X
X
1. All DDR2 SDRAM commands are defined by states of CS#, RAS#, CAS#, WE#, and CKE at
the rising edge of the clock.
Notes:
2. The state of ODT does not affect the states described in this table. The ODT function is
not available during self refresh. See ODT Timing (page 125) for details.
3.
4.
“X” means “H or L” (but a defined logic level) for valid IDD measurements.
BA2 is only applicable for densities ≥1Gb.
5. An n is the most significant address bit for a given density and configuration. Some larg-
er address bits may be “Don’t Care” during column addressing, depending on density
and configuration.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
68
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Commands
6. Bank addresses (BA) determine which bank is to be operated upon. BA during a LOAD
MODE command selects which mode register is programmed.
7. SELF REFRESH exit is asynchronous.
8. Burst reads or writes at BL = 4 cannot be terminated or interrupted. See Figure 48
(page 94) and Figure 60 (page 105) for other restrictions and details.
9. The power-down mode does not perform any REFRESH operations. The duration of power-
down is limited by the refresh requirements outlined in the AC parametric section.
Table 37: Truth Table – Current State Bank n – Command to Bank n
Notes: 1–6 apply to the entire table
Current
State
CS#
H
L
RAS#
CAS#
WE#
X
H
H
H
L
Command/Action
DESELECT (NOP/continue previous operation)
NO OPERATION (NOP/continue previous operation)
ACTIVATE (select and activate row)
REFRESH
Notes
Any
X
H
L
X
H
H
L
Idle
L
L
L
7
L
L
L
LOAD MODE
7
Row active
L
H
H
L
L
H
L
READ (select column and start READ burst)
WRITE (select column and start WRITE burst)
PRECHARGE (deactivate row in bank or banks)
READ (select column and start new READ burst)
WRITE (select column and start WRITE burst)
PRECHARGE (start PRECHARGE)
8
L
L
8
L
H
L
L
9
Read (auto
precharge
disabled)
L
H
H
L
H
L
8
L
L
8, 10
L
H
L
L
9
8
8
9
Write
L
H
H
L
H
L
READ (select column and start READ burst)
WRITE (select column and start new WRITE burst)
PRECHARGE (start PRECHARGE)
(auto pre-
charge disa-
bled)
L
L
L
H
L
1. This table applies when CKEn - 1 was HIGH and CKEn is HIGH and after tXSNR has been
Notes:
met (if the previous state was self refresh).
2. This table is bank-specific, except where noted (the current state is for a specific bank
and the commands shown are those allowed to be issued to that bank when in that
state). Exceptions are covered in the notes below.
3. Current state definitions:
The bank has been precharged, tRP has been met, and any READ burst is com-
plete.
Idle:
Row
A row in the bank has been activated, and tRCD has been met. No data bursts/
active: accesses and no register accesses are in progress.
Read: A READ burst has been initiated, with auto precharge disabled and has not yet
terminated.
Write: A WRITE burst has been initiated with auto precharge disabled and has not yet
terminated.
4. The following states must not be interrupted by a command issued to the same bank.
Issue DESELECT or NOP commands, or allowable commands to the other bank, on any
clock edge occurring during these states. Allowable commands to the other bank are
determined by its current state and this table, and according to Table 38 (page 71).
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
69
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Commands
Precharge:
Starts with registration of a PRECHARGE command and ends when tRP
is met. After tRP is met, the bank will be in the idle state.
Read with au- Starts with registration of a READ command with auto precharge ena-
to precharge bled and ends when tRP has been met. After tRP is met, the bank will
enabled:
be in the idle state.
Row activate: Starts with registration of an ACTIVATE command and ends when
tRCD is met. After tRCD is met, the bank will be in the row active state.
Write with au- Starts with registration of a WRITE command with auto precharge ena-
to precharge bled and ends when tRP has been met. After tRP is met, the bank will
enabled:
be in the idle state.
5. The following states must not be interrupted by any executable command (DESELECT or
NOP commands must be applied on each positive clock edge during these states):
Refresh:
Starts with registration of a REFRESH command and ends when tRFC is
met. After tRFC is met, the DDR2 SDRAM will be in the all banks idle state.
Accessing
mode
register:
Starts with registration of the LOAD MODE command and ends when
tMRD has been met. After tMRD is met, the DDR2 SDRAM will be in the
all banks idle state.
Precharge Starts with registration of a PRECHARGE ALL command and ends when
all:
tRP is met. After tRP is met, all banks will be in the idle state.
6. All states and sequences not shown are illegal or reserved.
7. Not bank-specific; requires that all banks are idle and bursts are not in progress.
8. READs or WRITEs listed in the Command/Action column include READs or WRITEs with
auto precharge enabled and READs or WRITEs with auto precharge disabled.
9. May or may not be bank-specific; if multiple banks are to be precharged, each must be
in a valid state for precharging.
10. A WRITE command may be applied after the completion of the READ burst.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
70
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Commands
Table 38: Truth Table – Current State Bank n – Command to Bank m
Notes: 1–6 apply to the entire table
Current State
CS#
H
L
RAS# CAS# WE#
Command/Action
DESELECT (NOP/continue previous operation)
NO OPERATION (NOP/continue previous operation)
Any command otherwise allowed to bank m
ACTIVATE (select and activate row)
READ (select column and start READ burst)
WRITE (select column and start WRITE burst)
PRECHARGE
Notes
Any
X
H
X
L
X
H
X
H
L
X
H
X
H
H
L
Idle
X
L
Row
active, active,
or precharge
L
H
H
L
7
7
L
L
L
H
H
L
L
Read (auto
precharge
disabled)
L
L
H
H
L
ACTIVATE (select and activate row)
READ (select column and start new READ burst)
WRITE (select column and start WRITE burst)
PRECHARGE
L
H
H
L
7
L
L
7, 8
L
H
H
L
L
Write (auto pre-
charge
disabled)
L
L
H
H
L
ACTIVATE (select and activate row)
READ (select column and start READ burst)
WRITE (select column and start new WRITE burst)
PRECHARGE
L
H
H
L
7, 9, 10
7
L
L
L
H
H
L
L
Read (with
auto
precharge)
L
L
H
H
L
ACTIVATE (select and activate row)
READ (select column and start new READ burst)
WRITE (select column and start WRITE burst)
PRECHARGE
L
H
H
L
7
L
L
7, 8
L
H
H
L
L
Write (with
auto
precharge)
L
L
H
H
L
ACTIVATE (select and activate row)
READ (select column and start READ burst)
WRITE (select column and start new WRITE burst)
PRECHARGE
L
H
H
L
7, 10
7
L
L
L
H
L
1. This table applies when CKEn - 1 was HIGH and CKEn is HIGH and after tXSNR has been
Notes:
met (if the previous state was self refresh).
2. This table describes an alternate bank operation, except where noted (the current state
is for bank n and the commands shown are those allowed to be issued to bank m, assum-
ing that bank m is in such a state that the given command is allowable). Exceptions are
covered in the notes below.
3. Current state definitions:
Idle:
The bank has been precharged, tRP has been met, and any READ
burst is complete.
Row active:
Read:
A row in the bank has been activated and tRCD has been met.
No data bursts/accesses and no register accesses are in progress.
A READ burst has been initiated with auto precharge disabled
and has not yet terminated.
Write:
A WRITE burst has been initiated with auto precharge disabled
and has not yet terminated.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
71
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Commands
READ with auto
The READ with auto precharge enabled or WRITE with auto pre-
precharge enabled/ charge enabled states can each be broken into two parts: the
WRITE with auto
access period and the precharge period. For READ with auto pre-
precharge enabled: charge, the precharge period is defined as if the same burst was
executed with auto precharge disabled and then followed with
the earliest possible PRECHARGE command that still accesses all
of the data in the burst. For WRITE with auto precharge, the pre-
charge period begins when tWR ends, with tWR measured as if
auto precharge was disabled. The access period starts with regis-
tration of the command and ends where the precharge period
(or tRP) begins. This device supports concurrent auto precharge
such that when a READ with auto precharge is enabled or a
WRITE with auto precharge is enabled, any command to other
banks is allowed, as long as that command does not interrupt
the read or write data transfer already in process. In either case,
all other related limitations apply (contention between read da-
ta and write data must be avoided).
The minimum delay from a READ or WRITE command with auto precharge enabled to
a command to a different bank is summarized in Table 39 (page 72).
4. REFRESH and LOAD MODE commands may only be issued when all banks are idle.
5. Not used.
6. All states and sequences not shown are illegal or reserved.
7. READs or WRITEs listed in the Command/Action column include READs or WRITEs with
auto precharge enabled and READs or WRITEs with auto precharge disabled.
8. A WRITE command may be applied after the completion of the READ burst.
9. Requires appropriate DM.
10. The number of clock cycles required to meet tWTR is either two or tWTR/tCK, whichever
is greater.
Table 39: Minimum Delay with Auto Precharge Enabled
Minimum Delay
From Command (Bank n)
To Command (Bank m)
READ or READ with auto precharge
WRITE or WRITE with auto precharge
PRECHARGE or ACTIVATE
(with Concurrent Auto Precharge) Units
WRITE with auto precharge
(CL - 1) + (BL/2) + tWTR
tCK
tCK
tCK
tCK
tCK
tCK
(BL/2)
1
(BL/2)
(BL/2) + 2
1
READ with auto precharge
READ or READ with auto precharge
WRITE or WRITE with auto precharge
PRECHARGE or ACTIVATE
DESELECT
The DESELECT function (CS# HIGH) prevents new commands from being executed by
the DDR2 SDRAM. The DDR2 SDRAM is effectively deselected. Operations already in
progress are not affected. DESELECT is also referred to as COMMAND INHIBIT.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
72
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Commands
NO OPERATION (NOP)
The NO OPERATION (NOP) command is used to instruct the selected DDR2 SDRAM to
perform a NOP (CS# is LOW; RAS#, CAS#, and WE are HIGH). This prevents unwanted
commands from being registered during idle or wait states. Operations already in pro-
gress are not affected.
LOAD MODE (LM)
ACTIVATE
The mode registers are loaded via bank address and address inputs. The bank address
balls determine which mode register will be programmed. See Mode Register (MR)
(page 74). The LM command can only be issued when all banks are idle, and a subse-
quent executable command cannot be issued until tMRD is met.
The ACTIVATE command is used to open (or activate) a row in a particular bank for a
subsequent access. The value on the bank address inputs determines the bank, and the
address inputs select the row. This row remains active (or open) for accesses until a pre-
charge command is issued to that bank. A precharge command must be issued before
opening a different row in the same bank.
READ
The READ command is used to initiate a burst read access to an active row. The value
on the bank address inputs determine the bank, and the address provided on address
inputs A0–Ai (where Ai is the most significant column address bit for a given configura-
tion) selects the starting column location. The value on input A10 determines whether
or not auto precharge is used. If auto precharge is selected, the row being accessed will
be precharged at the end of the read burst; if auto precharge is not selected, the row will
remain open for subsequent accesses.
DDR2 SDRAM also supports the AL feature, which allows a READ or WRITE command
to be issued prior to tRCD (MIN) by delaying the actual registration of the READ/WRITE
command to the internal device by AL clock cycles.
WRITE
The WRITE command is used to initiate a burst write access to an active row. The value
on the bank select inputs selects the bank, and the address provided on inputs A0–Ai
(where Ai is the most significant column address bit for a given configuration) selects
the starting column location. The value on input A10 determines whether or not auto
precharge is used. If auto precharge is selected, the row being accessed will be pre-
charged at the end of the WRITE burst; if auto precharge is not selected, the row will
remain open for subsequent accesses.
DDR2 SDRAM also supports the AL feature, which allows a READ or WRITE command
to be issued prior to tRCD (MIN) by delaying the actual registration of the READ/WRITE
command to the internal device by AL clock cycles.
Input data appearing on the DQ is written to the memory array subject to the DM input
logic level appearing coincident with the data. If a given DM signal is registered LOW,
the corresponding data will be written to memory; if the DM signal is registered HIGH,
the corresponding data inputs will be ignored, and a WRITE will not be executed to that
byte/column location (see Figure 65 (page 110)).
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
73
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Mode Register (MR)
PRECHARGE
The PRECHARGE command is used to deactivate the open row in a particular bank or
the open row in all banks. The bank(s) will be available for a subsequent row activation
a specified time (tRP) after the PRECHARGE command is issued, except in the case of
concurrent auto precharge, where a READ or WRITE command to a different bank is
allowed as long as it does not interrupt the data transfer in the current bank and does
not violate any other timing parameters. After a bank has been precharged, it is in the
idle state and must be activated prior to any READ or WRITE commands being issued to
that bank. A PRECHARGE command is allowed if there is no open row in that bank (idle
state) or if the previously open row is already in the process of precharging. However,
the precharge period will be determined by the last PRECHARGE command issued to
the bank.
REFRESH
REFRESH is used during normal operation of the DDR2 SDRAM and is analogous to CAS#-
before-RAS# (CBR) REFRESH. All banks must be in the idle mode prior to issuing a
REFRESH command. This command is nonpersistent, so it must be issued each time a
refresh is required. The addressing is generated by the internal refresh controller. This
makes the address bits a “Don’t Care” during a REFRESH command.
SELF REFRESH
The SELF REFRESH command can be used to retain data in the DDR2 SDRAM, even if
the rest of the system is powered down. When in the self refresh mode, the DDR2
SDRAM retains data without external clocking. All power supply inputs (including Vref)
must be maintained at valid levels upon entry/exit and during SELF REFRESH operation.
The SELF REFRESH command is initiated like a REFRESH command except CKE is
LOW. The DLL is automatically disabled upon entering self refresh and is automatically
enabled upon exiting self refresh.
Mode Register (MR)
The mode register is used to define the specific mode of operation of the DDR2 SDRAM.
This definition includes the selection of a burst length, burst type, CAS latency, operat-
ing mode, DLL RESET, write recovery, and power-down mode, as shown in Figure 35
(page 75). Contents of the mode register can be altered by re-executing the LOAD
MODE (LM) command. If the user chooses to modify only a subset of the MR variables,
all variables must be programmed when the command is issued.
The MR is programmed via the LM command and will retain the stored information
until it is programmed again or until the device loses power (except for bit M8, which is
self-clearing). Reprogramming the mode register will not alter the contents of the mem-
ory array, provided it is performed correctly.
The LM command can only be issued (or reissued) when all banks are in the precharged
state (idle state) and no bursts are in progress. The controller must wait the specified
time tMRD before initiating any subsequent operations such as an ACTIVATE com-
mand. Violating either of these requirements will result in an unspecified operation.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
74
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Mode Register (MR)
Burst Length
Burst length is defined by bits M0–M2, as shown in Figure 35. Read and write accesses
to the DDR2 SDRAM are burst-oriented, with the burst length being programmable to
either four or eight. The burst length determines the maximum number of column loca-
tions that can be accessed for a given READ or WRITE command.
When a READ or WRITE command is issued, a block of columns equal to the burst
length is effectively selected. All accesses for that burst take place within this block,
meaning that the burst will wrap within the block if a boundary is reached. The block is
uniquely selected by A2–Ai when BL = 4 and by A3–Ai when BL = 8 (where Ai is the most
significant column address bit for a given configuration). The remaining (least signifi-
cant) address bit(s) is (are) used to select the starting location within the block. The
programmed burst length applies to both read and write bursts.
Figure 35: MR Definition
1
2
BA2 BA1 BA0 An A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 Address Bus
16 15 14
n
12 11 10
PD WR
9
8
7
6
5
4
3
2
1
0
Mode Register (Mx)
0
MR
0
DLL TM CAS# Latency BT Burst Length
M2 M1 M0
Burst Length
M12 PD Mode
Mode
Normal
Test
M7
0
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
Fast exit
(normal)
Reserved
Reserved
4
1
1
Slow exit
(low power)
8
DLL Reset
No
M8
0
Reserved
Reserved
Reserved
Reserved
1
Yes
Write Recovery
M11 M10 M9
Reserved
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
2
3
4
5
6
7
8
Burst Type
Sequential
Interleaved
M3
0
1
CAS Latency (CL)
M6 M5 M4
Reserved
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
Reserved
Reserved
M15 M14
Mode Register Definition
3
4
5
6
7
0
0
1
1
0
1
0
1
Mode register (MR)
Extended mode register (EMR)
Extended mode register (EMR2)
Extended mode register (EMR3)
1.
Notes:
M16 (BA2) is only applicable for densities ≥1Gb, reserved for future use, and must be
programmed to “0.”
2. Mode bits (Mn) with corresponding address balls (An) greater than M12 (A12) are re-
served for future use and must be programmed to “0.”
3. Not all listed WR and CL options are supported in any individual speed grade.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
75
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Mode Register (MR)
Burst Type
Accesses within a given burst may be programmed to be either sequential or inter-
leaved. The burst type is selected via bit M3, as shown in Figure 35. The ordering of
accesses within a burst is determined by the burst length, the burst type, and the start-
ing column address, as shown in Table 40. DDR2 SDRAM supports 4-bit burst mode
and 8-bit burst mode only. For 8-bit burst mode, full interleaved address ordering is
supported; however, sequential address ordering is nibble-based.
Table 40: Burst Definition
Burst Length
Starting Column Address
Order of Accesses Within a Burst
(A2, A1, A0)
Burst Type = Sequential
Burst Type = Interleaved
0, 1, 2, 3
4
0 0
0 1
0, 1, 2, 3
1, 2, 3, 0
1, 0, 3, 2
1 0
2, 3, 0, 1
2, 3, 0, 1
1 1
3, 0, 1, 2
3, 2, 1, 0
8
0 0 0
0 0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
0, 1, 2, 3, 4, 5, 6, 7
1, 2, 3, 0, 5, 6, 7, 4
2, 3, 0, 1, 6, 7, 4, 5
3, 0, 1, 2, 7, 4, 5, 6
4, 5, 6, 7, 0, 1, 2, 3
5, 6, 7, 4, 1, 2, 3, 0
6, 7, 4, 5, 2, 3, 0, 1
7, 4, 5, 6, 3, 0, 1, 2
0, 1, 2, 3, 4, 5, 6, 7
1, 0, 3, 2, 5, 4, 7, 6
2, 3, 0, 1, 6, 7, 4, 5
3, 2, 1, 0, 7, 6, 5, 4
4, 5, 6, 7, 0, 1, 2, 3
5, 4, 7, 6, 1, 0, 3, 2
6, 7, 4, 5, 2, 3, 0, 1
7, 6, 5, 4, 3, 2, 1, 0
Operating Mode
DLL RESET
The normal operating mode is selected by issuing a command with bit M7 set to “0,”
and all other bits set to the desired values, as shown in Figure 35 (page 75). When bit M7
is “1,” no other bits of the mode register are programmed. Programming bit M7 to “1”
places the DDR2 SDRAM into a test mode that is only used by the manufacturer and
should not be used. No operation or functionality is guaranteed if M7 bit is “1.”
DLL RESET is defined by bit M8, as shown in Figure 35. Programming bit M8 to “1” will
activate the DLL RESET function. Bit M8 is self-clearing, meaning it returns back to a
value of “0” after the DLL RESET function has been issued.
Anytime the DLL RESET function is used, 200 clock cycles must occur before a READ
command can be issued to allow time for the internal clock to be synchronized with the
external clock. Failing to wait for synchronization to occur may result in a violation of
the tAC or tDQSCK parameters.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
76
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Mode Register (MR)
Write Recovery
Write recovery (WR) time is defined by bits M9–M11, as shown in Figure 35 (page 75).
The WR register is used by the DDR2 SDRAM during WRITE with auto precharge opera-
tion. During WRITE with auto precharge operation, the DDR2 SDRAM delays the inter-
nal auto precharge operation by WR clocks (programmed in bits M9–M11) from the last
data burst. An example of WRITE with auto precharge is shown in Figure 64 (page 109).
WR values of 2, 3, 4, 5, 6, 7, or 8 clocks may be used for programming bits M9–M11. The
user is required to program the value of WR, which is calculated by dividing tWR (in
nanoseconds) by tCK (in nanoseconds) and rounding up a noninteger value to the next
integer; WR (cycles) = tWR (ns)/tCK (ns). Reserved states should not be used as an un-
known operation or incompatibility with future versions may result.
Power-Down Mode
Active power-down (PD) mode is defined by bit M12, as shown in Figure 35. PD mode
enables the user to determine the active power-down mode, which determines perform-
ance versus power savings. PD mode bit M12 does not apply to precharge PD mode.
When bit M12 = 0, standard active PD mode, or “fast-exit” active PD mode, is enabled.
The tXARD parameter is used for fast-exit active PD exit timing. The DLL is expected to
be enabled and running during this mode.
When bit M12 = 1, a lower-power active PD mode, or “slow-exit” active PD mode, is
enabled. The tXARDS parameter is used for slow-exit active PD exit timing. The DLL can
be enabled but “frozen” during active PD mode because the exit-to-READ command
timing is relaxed. The power difference expected between IDD3P normal and IDD3P low-
power mode is defined in the DDR2 IDD Specifications and Conditions table.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
77
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Mode Register (MR)
CAS Latency (CL)
The CAS latency (CL) is defined by bits M4–M6, as shown in Figure 35 (page 75). CL is
the delay, in clock cycles, between the registration of a READ command and the availa-
bility of the first bit of output data. The CL can be set to 3, 4, 5, 6, or 7 clocks, depending
on the speed grade option being used.
DDR2 SDRAM does not support any half-clock latencies. Reserved states should not be
used as an unknown operation otherwise incompatibility with future versions may result.
DDR2 SDRAM also supports a feature called posted CAS additive latency (AL). This fea-
ture allows the READ command to be issued prior to tRCD (MIN) by delaying the
internal command to the DDR2 SDRAM by AL clocks. The AL feature is described in
further detail in Posted CAS Additive Latency (AL) (page 81).
Examples of CL = 3 and CL = 4 are shown in Figure 36; both assume AL = 0. If a READ
command is registered at clock edge n, and the CL is m clocks, the data will be available
nominally coincident with clock edge n + m (this assumes AL = 0).
Figure 36: CL
T0
T1
T2
T3
T4
T5
T6
CK#
CK
READ
NOP
NOP
NOP
NOP
NOP
NOP
Command
DQS, DQS#
DO
DO
DO
DO
DQ
n
n + 1
n + 2
n + 3
CL = 3 (AL = 0)
T0
T1
T2
T3
T4
T5
T6
CK#
CK
READ
NOP
NOP
NOP
NOP
NOP
NOP
Command
DQS, DQS#
DO
DO
DO
DO
DQ
n
n + 1
n + 2
n + 3
CL = 4 (AL = 0)
Transitioning data
Don’t care
1. BL = 4.
2. Posted CAS# additive latency (AL) = 0.
3. Shown with nominal tAC, tDQSCK, and tDQSQ.
Notes:
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
78
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Extended Mode Register (EMR)
Extended Mode Register (EMR)
The extended mode register controls functions beyond those controlled by the mode
register; these additional functions are DLL enable/disable, output drive strength, on-
die termination (ODT), posted AL, off-chip driver impedance calibration (OCD), DQS#
enable/disable, RDQS/RDQS# enable/disable, and output disable/enable. These func-
tions are controlled via the bits shown in Figure 37. The EMR is programmed via the LM
command and will retain the stored information until it is programmed again or the
device loses power. Reprogramming the EMR will not alter the contents of the memory
array, provided it is performed correctly.
The EMR must be loaded when all banks are idle and no bursts are in progress, and the
controller must wait the specified time tMRD before initiating any subsequent opera-
tion. Violating either of these requirements could result in an unspecified operation.
Figure 37: EMR Definition
1
2
BA2 BA1 BA0 An A12
A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 Address bus
Extended mode
16 15 14
n
12 11 10
Out
9
8
7
6
5
4
3
2
1
0
register (Ex)
0
MRS
RTT
0
OCD Program
Posted CAS# RTT ODS DLL
RDQS DQS#
Outputs
Enabled
Disabled
E0
DLL Enable
E12
0
0
1
E6 E2 RTT (Nominal)
Enable (normal)
Disable (test/debug)
1
0
0
1
1
0
1
0
1
RTT disabled
75Ω
E11 RDQS Enable
150Ω
E1
0
Output Drive Strength
0
1
No
50Ω
Full
Yes
1
Reduced
3
E10 DQS# Enable
Posted CAS# Additive Latency (AL)
E5 E4 E3
0
1
Enable
Disable
0
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
1
2
4
E9 E8 E7 OCD Operation
3
0
0
0
1
1
0
0
1
0
1
0
1
0
0
1
OCD exit
Reserved
Reserved
Reserved
4
5
6
Reserved
Enable OCD defaults
Mode Register Set
E15 E14
0
1
0
1
Mode register (MR)
0
0
1
1
Extended mode register (EMR)
Extended mode register (EMR2)
Extended mode register (EMR3)
1.
Notes:
E16 (BA2) is only applicable for densities ≥1Gb, reserved for future use, and must be pro-
grammed to “0.”
2. Mode bits (En) with corresponding address balls (An) greater than E12 (A12) are re-
served for future use and must be programmed to “0.”
3. Not all listed AL options are supported in any individual speed grade.
4. As detailed in the Initialization (page 85) section notes, during initialization of the
OCD operation, all three bits must be set to “1” for the OCD default state, then set to
“0” before initialization is finished.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
79
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Extended Mode Register (EMR)
DLL Enable/Disable
The DLL may be enabled or disabled by programming bit E0 during the LM command,
as shown in Figure 37 (page 79). These specifications are applicable when the DLL is
enabled for normal operation. DLL enable is required during power-up initialization
and upon returning to normal operation after having disabled the DLL for the purpose
of debugging or evaluation. Enabling the DLL should always be followed by resetting
the DLL using the LM command.
The DLL is automatically disabled when entering SELF REFRESH operation and is auto-
matically re-enabled and reset upon exit of SELF REFRESH operation.
Anytime the DLL is enabled (and subsequently reset), 200 clock cycles must occur be-
fore a READ command can be issued to allow time for the internal clock to synchronize
with the external clock. Failing to wait for synchronization to occur may result in a viola-
tion of the tAC or tDQSCK parameters.
Anytime the DLL is disabled and the device is operated below 25 MHz, any AUTO RE-
FRESH command should be followed by a PRECHARGE ALL command.
Output Drive Strength
The output drive strength is defined by bit E1, as shown in Figure 37. The normal drive
strength for all outputs is specified to be SSTL_18. Programming bit E1 = 0 selects nor-
mal (full strength) drive strength for all outputs. Selecting a reduced drive strength
option (E1 = 1) will reduce all outputs to approximately 45 to 60 percent of the SSTL_18
drive strength. This option is intended for the support of lighter load and/or point-to-
point environments.
DQS# Enable/Disable
The DQS# ball is enabled by bit E10. When E10 = 0, DQS# is the complement of the
differential data strobe pair DQS/DQS#. When disabled (E10 = 1), DQS is used in a single-
ended mode and the DQS# ball is disabled. When disabled, DQS# should be left float-
ing; however, it may be tied to ground via a 20Ω to 10kΩ resistor. This function is also
used to enable/disable RDQS#. If RDQS is enabled (E11 = 1) and DQS# is enabled (E10 =
0), then both DQS# and RDQS# will be enabled.
RDQS Enable/Disable
The RDQS ball is enabled by bit E11, as shown in Figure 37. This feature is only applica-
ble to the x8 configuration. When enabled (E11 = 1), RDQS is identical in function and
timing to data strobe DQS during a READ. During a WRITE operation, RDQS is ignored
by the DDR2 SDRAM.
Output Enable/Disable
The OUTPUT ENABLE function is defined by bit E12, as shown in Figure 37. When ena-
bled (E12 = 0), all outputs (DQ, DQS, DQS#, RDQS, RDQS#) function normally. When
disabled (E12 = 1), all outputs (DQ, DQS, DQS#, RDQS, RDQS#) are disabled, thus remov-
ing output buffer current. The output disable feature is intended to be used during IDD
characterization of read current.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
80
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Extended Mode Register (EMR)
On-Die Termination (ODT)
ODT effective resistance, RTT(EFF), is defined by bits E2 and E6 of the EMR, as shown in
Figure 37 (page 79). The ODT feature is designed to improve signal integrity of the mem-
ory channel by allowing the DDR2 SDRAM controller to independently turn on/off ODT
for any or all devices. RTT effective resistance values of 50Ω, 75Ω, and 150Ω are selecta-
ble and apply to each DQ, DQS/DQS#, RDQS/RDQS#, UDQS/UDQS#, LDQS/LDQS#,
DM, and UDM/LDM signals. Bits (E6, E2) determine what ODT resistance is enabled by
turning on/off “sw1,” “sw2,” or “sw3.” The ODT effective resistance value is selected by
enabling switch “sw1,” which enables all R1 values that are 150Ω each, enabling an ef-
fective resistance of 75Ω (RTT2 [EFF] = R2/2). Similarly, if “sw2” is enabled, all R2 values
that are 300Ω each, enable an effective ODT resistance of 150Ω (RTT2[EFF] = R2/2).
Switch “sw3” enables R1 values of 100Ω, enabling effective resistance of 50Ω. Reserved
states should not be used, as an unknown operation or incompatibility with future ver-
sions may result.
The ODT control ball is used to determine when RTT(EFF) is turned on and off, assuming
ODT has been enabled via bits E2 and E6 of the EMR. The ODT feature and ODT input
ball are only used during active, active power-down (both fast-exit and slow-exit
modes), and precharge power-down modes of operation.
ODT must be turned off prior to entering self refresh mode. During power-up and initi-
alization of the DDR2 SDRAM, ODT should be disabled until the EMR command is
issued. This will enable the ODT feature, at which point the ODT ball will determine the
RTT(EFF) value. Anytime the EMR enables the ODT function, ODT may not be driven
HIGH until eight clocks after the EMR has been enabled (see Figure 80 (page 126) for
ODT timing diagrams).
Off-Chip Driver (OCD) Impedance Calibration
The OFF-CHIP DRIVER function is an optional DDR2 JEDEC feature not supported by
Micron and thereby must be set to the default state. Enabling OCD beyond the default
settings will alter the I/O drive characteristics and the timing and output I/O specifica-
tions will no longer be valid (see Initialization (page 85) for proper setting of OCD
defaults).
Posted CAS Additive Latency (AL)
Posted CAS additive latency (AL) is supported to make the command and data bus effi-
cient for sustainable bandwidths in DDR2 SDRAM. Bits E3–E5 define the value of AL, as
shown in Figure 37. Bits E3–E5 allow the user to program the DDR2 SDRAM with an AL
of 0, 1, 2, 3, 4, 5, or 6 clocks. Reserved states should not be used as an unknown opera-
tion or incompatibility with future versions may result.
In this operation, the DDR2 SDRAM allows a READ or WRITE command to be issued
t
prior to RCD (MIN) with the requirement that AL ≤ tRCD (MIN). A typical application
using this feature would set AL = tRCD (MIN) - 1 × tCK. The READ or WRITE command
is held for the time of the AL before it is issued internally to the DDR2 SDRAM device.
RL is controlled by the sum of AL and CL; RL = AL + CL. WRITE latency (WL) is equal to
RL minus one clock; WL = AL + CL - 1 × tCK. An example of RL is shown in Figure 38
(page 82). An example of a WL is shown in Figure 39 (page 82).
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
81
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Extended Mode Register (EMR)
Figure 38: READ Latency
T0
T1
T2
T3
T4
T5
T6
T7
T8
CK#
CK
Command
DQS, DQS#
ACTIVE n
READ n
NOP
NOP
NOP
NOP
NOP
NOP
NOP
t
RCD (MIN)
AL = 2
DO
DO
n + 1
DO
DO
n + 3
DQ
n
n + 2
CL = 3
RL = 5
Transitioning Data
Don’t Care
1. BL = 4.
Notes:
2. Shown with nominal tAC, tDQSCK, and tDQSQ.
3. RL = AL + CL = 5.
Figure 39: WRITE Latency
T0
T1
T2
T3
T4
T5
T6
T7
CK#
CK
ACTIVE n
WRITE n
NOP
NOP
NOP
NOP
NOP
NOP
Command
t
RCD (MIN)
DQS, DQS#
AL = 2
CL - 1 = 2
DI
DI
DI
DI
DQ
n
n + 1
n + 2
n + 3
WL = AL + CL - 1 = 4
Transitioning Data
Don’t Care
1. BL = 4.
2. CL = 3.
Notes:
3. WL = AL + CL - 1 = 4.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
82
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Extended Mode Register 2 (EMR2)
Extended Mode Register 2 (EMR2)
The extended mode register 2 (EMR2) controls functions beyond those controlled by
the mode register. Currently all bits in EMR2 are reserved, except for E7, which is used
in commercial or high-temperature operations, as shown in Figure 40. The EMR2 is pro-
grammed via the LM command and will retain the stored information until it is program-
med again or until the device loses power. Reprogramming the EMR will not alter the
contents of the memory array, provided it is performed correctly.
Bit E7 (A7) must be programmed as “1” to provide a faster refresh rate on IT and AT
devices if TC exceeds 85°C.
EMR2 must be loaded when all banks are idle and no bursts are in progress, and the
controller must wait the specified time tMRD before initiating any subsequent opera-
tion. Violating either of these requirements could result in an unspecified operation.
Figure 40: EMR2 Definition
1
2
BA2
BA1 BA0 An A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
Address bus
Extended mode
register (Ex)
16 15 14
n
12 11 10
9
0
8
0
7
6
5
0
4
0
3
0
2
0
1
0
0
0
0
0
0
SRT
0
MRS
0
0
E15 E14
Mode Register Set
E7
0
SRT Enable
0
0
1
1
0
1
0
1
Mode register (MR)
1X refresh rate (0°C to 85°C)
2X refresh rate (>85°C)
Extended mode register (EMR)
Extended mode register (EMR2)
Extended mode register (EMR3)
1
1.
Notes:
E16 (BA2) is only applicable for densities ≥1Gb, reserved for future use, and must be pro-
grammed to “0.”
2. Mode bits (En) with corresponding address balls (An) greater than E12 (A12) are re-
served for future use and must be programmed to “0.”
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
83
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Extended Mode Register 3 (EMR3)
Extended Mode Register 3 (EMR3)
The extended mode register 3 (EMR3) controls functions beyond those controlled by
the mode register. Currently all bits in EMR3 are reserved, as shown in Figure 41. The
EMR3 is programmed via the LM command and will retain the stored information until
it is programmed again or until the device loses power. Reprogramming the EMR will
not alter the contents of the memory array, provided it is performed correctly.
EMR3 must be loaded when all banks are idle and no bursts are in progress, and the
controller must wait the specified time tMRD before initiating any subsequent opera-
tion. Violating either of these requirements could result in an unspecified operation.
Figure 41: EMR3 Definition
1
2
BA2
BA1 BA0 An A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 Address bus
Extended mode
16 15 14
MRS
n
12 11 10
9
8
7
6
5
4
3
2
1
0
register (Ex)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
E15 E14
Mode Register Set
0
0
1
1
0
1
0
1
Mode register (MR)
Extended mode register (EMR)
Extended mode register (EMR2)
Extended mode register (EMR3)
1.
Notes:
E16 (BA2) is only applicable for densities ≥1Gb, is reserved for future use, and must be
programmed to “0.”
2. Mode bits (En) with corresponding address balls (An) greater than E12 (A12) are re-
served for future use and must be programmed to “0.”
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
84
© 2004 Micron Technology, Inc. All rights reserved.
Initialization
Figure 42: DDR2 Power-Up and Initialization
DDR2 SDRAM must be powered up and initialized in a predefined manner. Operational procedures other than those specified may result in unde-
fined operation. Figure 42 illustrates, and the notes outline, the sequence required for power-up and initialization.
VDD
VDDL
VDDQ
1
tVTD
1
VTT
VREF
Tk0
Tl0
Tm0
Tg0
Th0
Ti0
Tj0
Te0
Tf0
Tc0
Td0
Tb0
T0
Ta0
t
CK
CK#
CK
t
CL
t
CL
LVCMOS
low level
SSTL_18
low level
2
2
CKE
ODT
10
REF
7
14
Valid
5
6
8
9
10
REF
11
12
13
LM
3
Command
LM
PRE
LM
LM
LM
PRE
LM
LM
NOP
15
DM
16
Address
Code
Code
Code
A10 = 1
Code
Code
Code
Code
A10 = 1
Valid
High-Z
High-Z
High-Z
15
DQS
15
DQ
R
tt
4
3
t
t
t
t
t
t
t
t
t
MRD
t
T = 400ns (MIN)
t
T = 200µs (MIN)
RPA
MRD
MRD
MRD
MRD
RPA
RFC
See no te 10
RFC
MRD
MRD
Power-up:
EMR(2)
EMR(3)
EMR
V
and stable
DD
MR without
DLL RESET
EMR with
OCD default
EMR with
OCD exit
clock (CK, CK#)
200 cycles of CK are required before a READ command can be issued
Normal
operation
MR with
DLL RESET
Indicates a Break in
Time Scale
Don’t care
1Gb: x4, x8, x16 DDR2 SDRAM
1. Applying power; if CKE is maintained below 0.2 × VDDQ, outputs remain disabled. To
guarantee RTT (ODT resistance) is off, VREF must be valid and a low level must be applied
to the ODT ball (all other inputs may be undefined; I/Os and outputs must be less than
VDDQ during voltage ramp time to avoid DDR2 SDRAM device latch-up). VTT is not ap-
plied directly to the device; however, tVTD should be ≥0 to avoid device latch-up. At
least one of the following two sets of conditions (A or B) must be met to obtain a stable
supply state (stable supply defined as VDD, VDDL, VDDQ, VREF, and VTT are between their
minimum and maximum values as stated in Table 12 (page 41)):
Notes:
A. Single power source: The VDD voltage ramp from 300mV to VDD,min must take no lon-
ger than 200ms; during the VDD voltage ramp, |VDD - VDDQ| ≤ 0.3V. Once supply voltage
ramping is complete (when VDDQ crosses VDD,min), Table 12 specifications apply.
VDD, VDDL, and VDDQ are driven from a single power converter output
VTT is limited to 0.95V MAX
•
•
•
VREF tracks VDDQ/2; VREF must be within ±0.3V with respect to VDDQ/2 during supply
ramp time; does not need to be satisfied when ramping power down
• VDDQ ≥ VREF at all times
B. Multiple power sources: VDD ≥ VDDL ≥ VDDQ must be maintained during supply voltage
ramping, for both AC and DC levels, until supply voltage ramping completes (VDDQ
crosses VDD,min). Once supply voltage ramping is complete, Table 12 specifications apply.
Apply VDD and VDDL before or at the same time as VDDQ; VDD/VDDL voltage ramp time
must be ≤ 200ms from when VDD ramps from 300mV to VDD,min
Apply VDDQ before or at the same time as VTT; the VDDQ voltage ramp time from when
VDD,min is achieved to when VDDQ,min is achieved must be ≤ 500ms; while VDD is ramp-
ing, current can be supplied from VDD through the device to VDDQ
•
•
VREF must track VDDQ/2; VREF must be within ±0.3V with respect to VDDQ/2 during sup-
ply ramp time; VDDQ ≥ VREF must be met at all times; does not need to be satisfied
when ramping power down
•
•
Apply VTT; the VTT voltage ramp time from when VDDQ,min is achieved to when VTT,min
is achieved must be no greater than 500ms
2. CKE requires LVCMOS input levels prior to state T0 to ensure DQs are High-Z during de-
vice power-up prior to VREF being stable. After state T0, CKE is required to have SSTL_18
input levels. Once CKE transitions to a high level, it must stay HIGH for the duration of
the initialization sequence.
3. For a minimum of 200µs after stable power and clock (CK, CK#), apply NOP or DESELECT
commands, then take CKE HIGH.
4. Wait a minimum of 400ns then issue a PRECHARGE ALL command.
5. Issue a LOAD MODE command to the EMR(2). To issue an EMR(2) command, provide
LOW to BA0, and provide HIGH to BA1; set register E7 to “0” or “1” to select appropri-
ate self refresh rate; remaining EMR(2) bits must be “0” (see Extended Mode Register 2
(EMR2) (page 83) for all EMR(2) requirements).
6. Issue a LOAD MODE command to the EMR(3). To issue an EMR(3) command, provide
HIGH to BA0 and BA1; remaining EMR(3) bits must be “0.” Extended Mode Register 3
(EMR3) for all EMR(3) requirements.
7. Issue a LOAD MODE command to the EMR to enable DLL. To issue a DLL ENABLE com-
mand, provide LOW to BA1 and A0; provide HIGH to BA0; bits E7, E8, and E9 can be set
to “0” or “1;” Micron recommends setting them to “0;” remaining EMR bits must be
“0.” Extended Mode Register (EMR) (page 79) for all EMR requirements.
8. Issue a LOAD MODE command to the MR for DLL RESET. 200 cycles of clock input is re-
quired to lock the DLL. To issue a DLL RESET, provide HIGH to A8 and provide LOW to
BA1 and BA0; CKE must be HIGH the entire time the DLL is resetting; remaining MR bits
must be “0.” Mode Register (MR) (page 74) for all MR requirements.
9. Issue PRECHARGE ALL command.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
86
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
10. Issue two or more REFRESH commands.
11. Issue a LOAD MODE command to the MR with LOW to A8 to initialize device operation
(that is, to program operating parameters without resetting the DLL). To access the MR,
set BA0 and BA1 LOW; remaining MR bits must be set to desired settings. Mode Register
(MR) (page 74) for all MR requirements.
12. Issue a LOAD MODE command to the EMR to enable OCD default by setting bits E7, E8,
and E9 to “1,” and then setting all other desired parameters. To access the EMR, set BA0
LOW and BA1 HIGH (see Extended Mode Register (EMR) (page 79) for all EMR require-
ments.
13. Issue a LOAD MODE command to the EMR to enable OCD exit by setting bits E7, E8, and
E9 to “0,” and then setting all other desired parameters. To access the extended mode
registers, EMR, set BA0 LOW and BA1 HIGH for all EMR requirements.
14. The DDR2 SDRAM is now initialized and ready for normal operation 200 clock cycles af-
ter the DLL RESET at Tf0.
15. DM represents DM for the x4, x8 configurations and UDM, LDM for the x16 configura-
tion; DQS represents DQS, DQS#, UDQS, UDQS#, LDQS, LDQS#, RDQS, RDQS# for the
appropriate configuration (x4, x8, x16); DQ represents DQ0–DQ3 for x4, DQ–DQ7 for x8
and DQ0–DQ15 for x16.
16. A10 = PRECHARGE ALL, CODE = desired values for mode registers (bank addresses are
required to be decoded).
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
87
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
ACTIVATE
ACTIVATE
Before any READ or WRITE commands can be issued to a bank within the DDR2
SDRAM, a row in that bank must be opened (activated), even when additive latency is
used. This is accomplished via the ACTIVATE command, which selects both the bank
and the row to be activated.
After a row is opened with an ACTIVATE command, a READ or WRITE command may
be issued to that row subject to the tRCD specification. tRCD (MIN) should be divided
by the clock period and rounded up to the next whole number to determine the earliest
clock edge after the ACTIVATE command on which a READ or WRITE command can be
entered. The same procedure is used to convert other specification limits from time
units to clock cycles. For example, a tRCD (MIN) specification of 20ns with a 266 MHz
clock (tCK = 3.75ns) results in 5.3 clocks, rounded up to 6. This is shown in Figure 43,
which covers any case where 5 < tRCD (MIN)/tCK ≤ 6. Figure 43 also shows the case for
tRRD where 2 < tRRD (MIN)/tCK ≤ 3.
Figure 43: Example: Meeting tRRD (MIN) and tRCD (MIN)
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9
CK#
CK
Command
ACT
Row
NOP
NOP
ACT
Row
NOP
NOP
NOP
Row
NOP
NOP
RD/WR
Col
Address
Bank x
Bank y
Bank z
Bank y
Bank address
t
t
RRD
RRD
t
RCD
Don’t Care
A subsequent ACTIVATE command to a different row in the same bank can only be is-
sued after the previous active row has been closed (precharged). The minimum time
interval between successive ACTIVATE commands to the same bank is defined by tRC.
A subsequent ACTIVATE command to another bank can be issued while the first bank is
being accessed, which results in a reduction of total row-access overhead. The mini-
mum time interval between successive ACTIVATE commands to different banks is
defined by tRRD.
DDR2 devices with 8 banks (1Gb or larger) have an additional requirement: tFAW. This
requires no more than four ACTIVATE commands may be issued in any given tFAW
(MIN) period, as shown in Figure 44 (page 89).
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
88
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
ACTIVATE
Figure 44: Multibank Activate Restriction
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9
T10
CK#
CK
Command
ACT
Row
READ
ACT
Row
NOP
ACT
Row
READ
Col
ACT
READ
ACT
Row
READ
NOP
Col
Row
Col
Col
Address
Bank address
Bank a
Bank a
Bank b
Bank b
Bank c
Bank c
Bank d
Bank d
Bank e
t
RRD (MIN)
t
FAW (MIN)
Don’t Care
1. DDR2-533 (-37E, x4 or x8), tCK = 3.75ns, BL = 4, AL = 3, CL = 4, tRRD (MIN) = 7.5ns,
tFAW (MIN) = 37.5ns.
Note:
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
89
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
READ
READ
READ bursts are initiated with a READ command. The starting column and bank ad-
dresses are provided with the READ command, and auto precharge is either enabled or
disabled for that burst access. If auto precharge is enabled, the row being accessed is
automatically precharged at the completion of the burst. If auto precharge is disabled,
the row will be left open after the completion of the burst.
During READ bursts, the valid data-out element from the starting column address will
be available READ latency (RL) clocks later. RL is defined as the sum of AL and CL:
RL = AL + CL. The value for AL and CL are programmable via the MR and EMR com-
mands, respectively. Each subsequent data-out element will be valid nominally at the
next positive or negative clock edge (at the next crossing of CK and CK#). Figure 45
(page 91) shows examples of RL based on different AL and CL settings.
DQS/DQS# is driven by the DDR2 SDRAM along with output data. The initial LOW state
on DQS and the HIGH state on DQS# are known as the read preamble (tRPRE). The
LOW state on DQS and the HIGH state on DQS# coincident with the last data-out ele-
ment are known as the read postamble (tRPST).
Upon completion of a burst, assuming no other commands have been initiated, the DQ
will go High-Z. A detailed explanation of tDQSQ (valid data-out skew), tQH (data-out
window hold), and the valid data window are depicted in Figure 54 (page 99) and Fig-
ure 55 (page 100). A detailed explanation of tDQSCK (DQS transition skew to CK) and
tAC (data-out transition skew to CK) is shown in Figure 56 (page 101).
Data from any READ burst may be concatenated with data from a subsequent READ
command to provide a continuous flow of data. The first data element from the new
burst follows the last element of a completed burst. The new READ command should
be issued x cycles after the first READ command, where x equals BL/2 cycles (see Fig-
ure 46 (page 92)).
Nonconsecutive read data is illustrated in Figure 47 (page 93). Full-speed random
read accesses within a page (or pages) can be performed. DDR2 SDRAM supports the
use of concurrent auto precharge timing (see Table 41 (page 96)).
DDR2 SDRAM does not allow interrupting or truncating of any READ burst using BL = 4
operations. Once the BL = 4 READ command is registered, it must be allowed to com-
plete the entire READ burst. However, a READ (with auto precharge disabled) using BL
= 8 operation may be interrupted and truncated only by another READ burst as long as
the interruption occurs on a 4-bit boundary due to the 4n prefetch architecture of
DDR2 SDRAM. As shown in Figure 48 (page 94), READ burst BL = 8 operations may
not be interrupted or truncated with any other command except another READ com-
mand.
Data from any READ burst must be completed before a subsequent WRITE burst is al-
lowed. An example of a READ burst followed by a WRITE burst is shown in Figure 49
(page 94). The tDQSS (NOM) case is shown (tDQSS [MIN] and tDQSS [MAX] are de-
fined in Figure 57 (page 103)).
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
90
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
READ
Figure 45: READ Latency
T0
T1
T2
T3
T3n
T4
T4n
T5
CK#
CK
Command
READ
NOP
NOP
NOP
NOP
NOP
Bank a,
Col n
Address
RL = 3 (AL = 0, CL = 3)
DQS, DQS#
DQ
DO
n
T0
T1
T2
T3
T4
T4n
T5
T5n
CK#
CK
Command
READ
NOP
NOP
NOP
NOP
NOP
Bank a,
Col n
Address
AL = 1
CL = 3
RL = 4 (AL = 1 + CL = 3)
DQS, DQS#
DQ
DO
n
T0
T1
T2
NOP
T3
T3n
T4
T4n
T5
CK#
CK
Command
READ
NOP
NOP
NOP
NOP
Bank a,
Col n
Address
RL = 4 (AL = 0, CL = 4)
DQS, DQS#
DQ
DO
n
Transitioning Data
Don’t Care
1. DO n = data-out from column n.
Notes:
2. BL = 4.
3. Three subsequent elements of data-out appear in the programmed order following
DO n.
4. Shown with nominal tAC, tDQSCK, and tDQSQ.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
91
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
READ
Figure 46: Consecutive READ Bursts
T5n
T6n
T0
T1
NOP
CCD
T2
T3
T3n
T4
T4n
T5
T6
CK#
CK
Command
Address
READ
READ
NOP
NOP
NOP
NOP
Bank,
Bank,
Col n
Col b
t
RL = 3
DQS, DQS#
DQ
DO
DO
n
b
T0
T1
T2
T2n
T3
T5n
T6n
T3n
T4
T4n
T5
T6
CK#
CK
Command
Address
READ
NOP
READ
NOP
NOP
NOP
NOP
Bank,
Bank,
Col n
Col b
t
CCD
RL = 4
DQS, DQS#
DQ
DO
DO
n
b
Transitioning Data
Don’t Care
1. DO n (or b) = data-out from column n (or column b).
Notes:
2. BL = 4.
3. Three subsequent elements of data-out appear in the programmed order following
DO n.
4. Three subsequent elements of data-out appear in the programmed order following
DO b.
5. Shown with nominal tAC, tDQSCK, and tDQSQ.
6. Example applies only when READ commands are issued to same device.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
92
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
READ
Figure 47: Nonconsecutive READ Bursts
T0
T1
T2
T3 T3n T4 T4n T5
T6 T6n T7 T7n T8
CK#
CK
Command
READ
NOP
NOP
READ
NOP
NOP
NOP
NOP
NOP
Bank,
Bank,
Address
Col n
Col b
CL = 3
DQS, DQS#
DQ
DO
DO
n
b
T0
T1
T2
T3
T4 T4n T5 T5n T6
T7 T7n T8
CK#
CK
Command
READ
NOP
NOP
READ
NOP
NOP
NOP
NOP
NOP
Bank,
Bank,
Address
Col n
Col b
CL = 4
DQS, DQS#
DQ
DO
DO
n
b
Transitioning Data
Don’t Care
1. DO n (or b) = data-out from column n (or column b).
Notes:
2. BL = 4.
3. Three subsequent elements of data-out appear in the programmed order following
DO n.
4. Three subsequent elements of data-out appear in the programmed order following
DO b.
5. Shown with nominal tAC, tDQSCK, and tDQSQ.
6. Example applies when READ commands are issued to different devices or nonconsecu-
tive READs.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
93
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
READ
Figure 48: READ Interrupted by READ
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9
CK#
CK
1
2
NOP
3
2
NOP
Command
Valid
Valid
Valid
Valid
Valid
Valid
READ
READ
4
Valid
4
Valid
Address
A10
5
Valid
DQS, DQS#
DQ
DO
DO
DO
DO
DO
DO
DO
DO
DO
DO
DO
DO
CL = 3 (AL = 0)
t
CCD
CL = 3 (AL = 0)
Transitioning Data
Don’t Care
1. BL = 8 required; auto precharge must be disabled (A10 = LOW).
Notes:
2. NOP or COMMAND INHIBIT commands are valid. PRECHARGE command cannot be is-
sued to banks used for READs at T0 and T2.
3. Interrupting READ command must be issued exactly 2 × tCK from previous READ.
4. READ command can be issued to any valid bank and row address (READ command at T0
and T2 can be either same bank or different bank).
5. Auto precharge can be either enabled (A10 = HIGH) or disabled (A10 = LOW) by the in-
terrupting READ command.
6. Example shown uses AL = 0; CL = 3, BL = 8, shown with nominal tAC, tDQSCK, and tDQSQ.
Figure 49: READ-to-WRITE
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9
T10
T11
CK#
CK
Command
ACT n
READ n
NOP
NOP
NOP
WRITE
NOP
NOP
NOP
NOP
NOP
NOP
DQS, DQS#
t
RCD = 3
WL = RL - 1 = 4
DO
DO
n + 1
DO
n + 2
DO
n + 3
DI
DI
n + 1
DI
DI
n + 3
DQ
n
n
n + 2
AL = 2
CL = 3
RL = 5
Transitioning Data
Don’t Care
1. BL = 4; CL = 3; AL = 2.
2. Shown with nominal tAC, tDQSCK, and tDQSQ.
Notes:
READ with Precharge
A READ burst may be followed by a PRECHARGE command to the same bank, provided
auto precharge is not activated. The minimum READ-to-PRECHARGE command spac-
ing to the same bank has two requirements that must be satisfied: AL + BL/2 clocks and
tRTP. tRTP is the minimum time from the rising clock edge that initiates the last 4-bit
prefetch of a READ command to the PRECHARGE command. For BL = 4, this is the time
from the actual READ (AL after the READ command) to PRECHARGE command. For
BL = 8, this is the time from AL + 2 × CK after the READ-to-PRECHARGE command.
Following the PRECHARGE command, a subsequent command to the same bank can-
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
94
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
READ
not be issued until tRP is met. However, part of the row precharge time is hidden during
the access of the last data elements.
Examples of READ-to-PRECHARGE for BL = 4 are shown in Figure 50 and in Figure 51
for BL = 8. The delay from READ-to-PRECHARGE period to the same bank is AL + BL/
2 - 2CK + MAX (tRTP/tCK or 2 × CK) where MAX means the larger of the two.
Figure 50: READ-to-PRECHARGE – BL = 4
4-bit
prefetch
T1
T0
T2
T3
T4
T5
T6
T7
CK#
CK
Command
READ
NOP
NOP
PRE
NOP
NOP
ACT
NOP
t
t
AL + BL/2 - 2CK + MAX ( RTP/ CK or 2CK)
Address
A10
Bank a
Bank a
Bank a
Valid
Valid
AL = 1
CL = 3
DQS, DQS#
DQ
t
≥ RTP (MIN)
DO
DO
DO
DO
t
t
≥ RAS (MIN)
≥ RP (MIN)
t
≥ RC (MIN)
Transitioning Data
Don’t Care
1. RL = 4 (AL = 1, CL = 3); BL = 4.
Notes:
tRTP ≥ 2 clocks.
2.
3. Shown with nominal tAC, tDQSCK, and tDQSQ.
Figure 51: READ-to-PRECHARGE – BL = 8
First 4-bit
prefetch
T1
Second 4-bit
prefetch
T3
T0
T2
T4
T5
T6
T7
T8
CK#
CK
Command READ
NOP
NOP
NOP
NOP
PRE
NOP
NOP
ACT
t
t
AL + BL/2 - 2CK + MAX ( RTP/ CK or 2CK)
Address
A10
Bank a
Bank a
Bank a
Valid
Valid
AL = 1
CL = 3
DQS, DQS#
DQ
DO
DO
DO
DO
DO
DO
RP (MIN)
DO
DO
≥t
≥t
RTP (MIN)
≥t
RAS (MIN)
≥t
RC (MIN)
Transitioning Data
Don’t Care
1. RL = 4 (AL = 1, CL = 3); BL = 8.
Notes:
tRTP ≥ 2 clocks.
2.
3. Shown with nominal tAC, tDQSCK, and tDQSQ.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
95
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
READ
READ with Auto Precharge
If A10 is high when a READ command is issued, the READ with auto precharge function
is engaged. The DDR2 SDRAM starts an auto precharge operation on the rising clock
edge that is AL + (BL/2) cycles later than the read with auto precharge command provi-
ded tRAS (MIN) and tRTP are satisfied. If tRAS (MIN) is not satisfied at this rising clock
edge, the start point of the auto precharge operation will be delayed until tRAS (MIN) is
satisfied. If tRTP (MIN) is not satisfied at this rising clock edge, the start point of the
auto precharge operation will be delayed until tRTP (MIN) is satisfied. When the inter-
nal precharge is pushed out by tRTP, tRP starts at the point where the internal pre-
charge happens (not at the next rising clock edge after this event).
When BL = 4, the minimum time from READ with auto precharge to the next ACTIVATE
command is AL + (tRTP + tRP)/tCK. When BL = 8, the minimum time from READ with
auto precharge to the next ACTIVATE command is AL + 2 clocks + (tRTP + tRP)/tCK. The
term (tRTP + tRP)/tCK is always rounded up to the next integer. A general purpose equa-
tion can also be used: AL + BL/2 - 2CK + (tRTP + tRP)/tCK. In any event, the internal
precharge does not start earlier than two clocks after the last 4-bit prefetch.
READ with auto precharge command may be applied to one bank while another bank is
operational. This is referred to as concurrent auto precharge operation, as noted in Ta-
ble 41. Examples of READ with precharge and READ with auto precharge with applica-
ble timing requirements are shown in Figure 52 (page 97) and Figure 53 (page 98),
respectively.
Table 41: READ Using Concurrent Auto Precharge
Minimum Delay
From Command (Bank n)
To Command (Bank m)
READ or READ with auto precharge
WRITE or WRITE with auto precharge
PRECHARGE or ACTIVATE
(with Concurrent Auto Precharge) Units
READ with auto precharge
BL/2
(BL/2) + 2
1
tCK
tCK
tCK
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
96
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
READ
Figure 52: Bank Read – Without Auto Precharge
T1
T0
T2
T3
T4
T5
T6
T7
T7n
T8
T8n
T9
CK#
CK
t
t
CL
t
CH
CK
CKE
3
1
1
1
2
1
1
1
NOP
Command
ACT
RA
PRE
ACT
RA
NOP
NOP
NOP
READ
NOP
NOP
4
t
RTP
Col n
Address
A10
All banks
One bank
RA
RA
5
6
Bank address
Bank x
Bank x
Bank x
Bank x
t
CL = 3
RCD
t
RP
3
t
RAS
t
RC
DM
t
t
DQSCK (MIN)
t
Case 1: AC (MIN) and DQSCK (MIN)
t
RPST
t
RPRE
7
7
DQS, DQS#
t
LZ (MIN)
DO
8
DQ
n
t
LZ (MIN)
t
t
t
AC (MIN)
HZ (MIN)
t
DQSCK (MAX)
t
t
Case 2: AC (MAX) and DQSCK (MAX)
t
RPST
RPRE
7
7
DQS, DQS#
t
LZ (MAX)
8
DO
DQ
n
t
t
t
AC (MAX)
HZ (MAX)
LZ (MIN)
Transitioning Data
Don’t Care
1. NOP commands are shown for ease of illustration; other commands may be valid at
these times.
Notes:
2. BL = 4 and AL = 0 in the case shown.
3. The PRECHARGE command can only be applied at T6 if tRAS (MIN) is met.
4. READ-to-PRECHARGE = AL + BL/2 - 2CK + MAX (tRTP/tCK or 2CK).
5. Disable auto precharge.
6.
“Don’t Care” if A10 is HIGH at T5.
7. I/O balls, when entering or exiting High-Z, are not referenced to a specific voltage level,
but to when the device begins to drive or no longer drives, respectively.
8. DO n = data-out from column n; subsequent elements are applied in the programmed
order.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
97
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
READ
Figure 53: Bank Read – with Auto Precharge
T1
T0
T2
T3
T4
T5
T6
T7
T7n
T8
T8n
CK#
CK
t
t
t
CL
CK
CH
CKE
1
1
1
2,3
READ
1
1
1
1
1
NOP
Command
NOP
ACT
RA
ACT
RA
NOP
NOP
NOP
NOP
NOP
Address
A10
Col n
4
RA
RA
Bank address
Bank x
Bank x
Bank x
AL = 1
CL = 3
t
t
RTP
RCD
t
RP
t
RAS
t
RC
DM
t
t
DQSCK (MIN)
t
t
RPST
Case 1: AC (MIN) and DQSCK (MIN)
t
RPRE
5
5
DQS, DQS#
t
LZ (MIN)
DO
6
DQ
n
t
LZ (MIN)
t
t
HZ (MIN)
AC (MIN)
t
DQSCK (MAX)
t
t
Case 2: AC (MAX) and DQSCK (MAX)
t
t
RPST
RPRE
5
5
DQS, DQS#
t
LZ (MAX)
6
DO
DQ
n
t
t
t
HZ (MAX)
LZ (MAX)
AC (MAX)
4-bit
prefetch
Internal
precharge
Transitioning Data
Don’t Care
1. NOP commands are shown for ease of illustration; other commands may be valid at
these times.
Notes:
2. BL = 4, RL = 4 (AL = 1, CL = 3) in the case shown.
3. The DDR2 SDRAM internally delays auto precharge until both tRAS (MIN) and tRTP (MIN)
have been satisfied.
4. Enable auto precharge.
5. I/O balls, when entering or exiting High-Z, are not referenced to a specific voltage level,
but to when the device begins to drive or no longer drives, respectively.
6. DO n = data-out from column n; subsequent elements are applied in the programmed
order.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
98
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
READ
Figure 54: x4, x8 Data Output Timing – tDQSQ, tQH, and Data Valid Window
T1
T2
T2n
T3
T3n
T4
CK#
CK
t
1
HP
t
1
t
1
HP
t
HP
1
t 1
HP
t
t
1
HP
HP
2
t
2
t
2
t
2
DQSQ
DQSQ
DQSQ
DQSQ
DQS#
3
DQS
DQ (last data valid)
4
4
4
4
4
4
DQ
DQ
DQ
DQ
DQ
DQ
DQ (first data no longer valid)
t
QH
5
t
5
t
QH
5
t
QH
5
QH
t
t
t
QHS
t
QHS
QHS
QHS
DQ (last data valid)
T2
T2
T2n
T2n
T3
T3n
DQ (first data no longer valid)
T3
T3n
6
All DQs and DQS collectively
T2
T2n
T3
T3n
Earliest signal transition
Latest signal transition
Data
Data
valid
window
Data
valid
window
Data
valid
window
valid
window
1. tHP is the lesser of tCL or tCH clock transitions collectively when a bank is active.
2. tDQSQ is derived at each DQS clock edge, is not cumulative over time, begins with DQS
transitions, and ends with the last valid transition of DQ.
Notes:
3. DQ transitioning after the DQS transition defines the tDQSQ window. DQS transitions at
T2 and at T2n are “early DQS,” at T3 are “nominal DQS,” and at T3n are “late DQS.”
4. DQ0, DQ1, DQ2, DQ3 for x4 or DQ0–DQ7 for x8.
5. tQH is derived from tHP: tQH = tHP - tQHS.
6. The data valid window is derived for each DQS transition and is defined as tQH - tDQSQ.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
99
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
READ
Figure 55: x16 Data Output Timing – tDQSQ, tQH, and Data Valid Window
T1
T2
T2n
T3
T3n
T4
CK#
CK
1
1
1
1
1
1
HP
t
t
t
t
t
t
HP
HP
HP
HP
HP
2
2
2
2
DQSQ
t
t
t
t
DQSQ
DQSQ
DQSQ
LDSQ#
3
LDQS
4
4
4
4
4
4
4
4
DQ (last data valid)
DQ
DQ
DQ
DQ
DQ
DQ
DQ (first data no longer valid)
5
5
QH
QHS
t
t
5
5
QH
QHS
t
t
t
t
QH
QH
t
t
QHS
QHS
4
4
DQ (last data valid)
T2
T2
T2n
T2n
T3
T3n
DQ (first data no longer valid)
T3
T3
T3n
T3n
6
DQ0–DQ7 and LDQS collectively
T2
T2n
Data valid
window
Data valid
window
Data valid
window
Data valid
window
2
2
2
2
DQSQ
t
t
t
DQSQ
t
DQSQ
DQSQ
UDQS#
3
UDQS
7
7
7
7
7
7
7
7
DQ (last data valid)
DQ
DQ
DQ
DQ
DQ
DQ
DQ (first data no longer valid)
5
t
5
5
5
QH
QHS
t
t
t
t
t
QH
QH
QH
t
QHS
t
QHS
QHS
7
7
6
DQ (last data valid)
DQ (first data no longer valid)
DQ8–DQ15 and UDQS collectively
T2
T2
T2n
T2n
T3
T3
T3n
T3n
T2
T2n
T3
T3n
Data valid
window
Data valid
window
Data valid
window
Data valid
window
1. tHP is the lesser of tCL or tCH clock transitions collectively when a bank is active.
2. tDQSQ is derived at each DQS clock edge, is not cumulative over time, begins with DQS
transitions, and ends with the last valid transition of DQ.
Notes:
3. DQ transitioning after the DQS transitions define the tDQSQ window. LDQS defines the
lower byte, and UDQS defines the upper byte.
4. DQ0, DQ1, DQ2, DQ3, DQ4, DQ5, DQ6, or DQ7.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
100
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
WRITE
5. tQH is derived from tHP: tQH = tHP - tQHS.
6. The data valid window is derived for each DQS transition and is tQH - tDQSQ.
7. DQ8, DQ9, DQ10, D11, DQ12, DQ13, DQ14, or DQ15.
Figure 56: Data Output Timing – tAC and tDQSCK
1
T0
T1
T2
T3
t
T3n
T4
T4n
T5
T5n
T6
T6n
T7
CK#
CK
t
HZ (MAX)
2
2
t
t
DQSCK (MAX)
DQSCK (MIN)
LZ (MIN)
t
t
RPST
RPRE
DQS#/DQS or
3
LDQS#/LDQS/UDQ#/UDQS
DQ (last data valid)
DQ (first data valid)
T3
T3
T3
T3n
T3n
T4
T4
T4
T4n
T5
T5n
T5n
T6
T6
T6n
T6n
T4n
T4n
T5
T5
4
All DQs collectively
T3n
T5n
T6
T6n
t
t
5
t
5
t
HZ (MAX)
LZ (MIN)
AC (MIN)
AC (MAX)
1. READ command with CL = 3, AL = 0 issued at T0.
Notes:
2. tDQSCK is the DQS output window relative to CK and is the long-term component of
DQS skew.
3. DQ transitioning after DQS transitions define tDQSQ window.
4. All DQ must transition by tDQSQ after DQS transitions, regardless of tAC.
5. tAC is the DQ output window relative to CK and is the “long term” component of DQ
skew.
6. tLZ (MIN) and tAC (MIN) are the first valid signal transitions.
7. tHZ (MAX) and tAC (MAX) are the latest valid signal transitions.
8. I/O balls, when entering or exiting High-Z, are not referenced to a specific voltage level,
but to when the device begins to drive or no longer drives, respectively.
WRITE
WRITE bursts are initiated with a WRITE command. DDR2 SDRAM uses WL equal to RL
minus one clock cycle (WL = RL - 1CK) (see READ (page 73)). The starting column and
bank addresses are provided with the WRITE command, and auto precharge is either
enabled or disabled for that access. If auto precharge is enabled, the row being accessed
is precharged at the completion of the burst.
Note:
For the WRITE commands used in the following illustrations, auto precharge is disabled.
During WRITE bursts, the first valid data-in element will be registered on the first rising
edge of DQS following the WRITE command, and subsequent data elements will be reg-
istered on successive edges of DQS. The LOW state on DQS between the WRITE com-
mand and the first rising edge is known as the write preamble; the LOW state on DQS
following the last data-in element is known as the write postamble.
The time between the WRITE command and the first rising DQS edge is WL ±tDQSS.
Subsequent DQS positive rising edges are timed, relative to the associated clock edge,
as ±tDQSS. tDQSS is specified with a relatively wide range (25% of one clock cycle). All of
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
101
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
WRITE
the WRITE diagrams show the nominal case, and where the two extreme cases (tDQSS
[MIN] and tDQSS [MAX]) might not be intuitive, they have also been included. Figure 57
(page 103) shows the nominal case and the extremes of tDQSS for BL = 4. Upon comple-
tion of a burst, assuming no other commands have been initiated, the DQ will remain
High-Z and any additional input data will be ignored.
Data for any WRITE burst may be concatenated with a subsequent WRITE command to
provide continuous flow of input data. The first data element from the new burst is ap-
plied after the last element of a completed burst. The new WRITE command should be
issued x cycles after the first WRITE command, where x equals BL/2.
Figure 58 (page 104) shows concatenated bursts of BL = 4 and how full-speed random
write accesses within a page or pages can be performed. An example of nonconsecutive
WRITEs is shown in Figure 59 (page 104). DDR2 SDRAM supports concurrent auto pre-
charge options, as shown in Table 42.
DDR2 SDRAM does not allow interrupting or truncating any WRITE burst using BL = 4
operation. Once the BL = 4 WRITE command is registered, it must be allowed to com-
plete the entire WRITE burst cycle. However, a WRITE BL = 8 operation (with auto
precharge disabled) might be interrupted and truncated only by another WRITE burst
as long as the interruption occurs on a 4-bit boundary due to the 4n-prefetch architec-
ture of DDR2 SDRAM. WRITE burst BL = 8 operations may not be interrupted or
truncated with any command except another WRITE command, as shown in Figure 60
(page 105).
Data for any WRITE burst may be followed by a subsequent READ command. To follow
a WRITE, tWTR should be met, as shown in Figure 61 (page 106). The number of clock
cycles required to meet tWTR is either 2 or tWTR/tCK, whichever is greater. Data for any
WRITE burst may be followed by a subsequent PRECHARGE command. tWR must be
met, as shown in Figure 62 (page 107). tWR starts at the end of the data burst, regard-
less of the data mask condition.
Table 42: WRITE Using Concurrent Auto Precharge
From Command
To Command
Minimum Delay
(Bank n)
(Bank m)
(with Concurrent Auto Precharge) Units
WRITE with auto precharge
READ or READ with auto precharge
WRITE or WRITE with auto precharge
PRECHARGE or ACTIVATE
(CL - 1) + (BL/2) + tWTR
tCK
tCK
tCK
(BL/2)
1
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
102
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
WRITE
Figure 57: Write Burst
T0
T1
T2
T2n
T3
T3n
T4
CK#
CK
Command
Address
WRITE
NOP
NOP
NOP
NOP
Bank a,
Col b
t
WL ± DQSS
t
DQSS (NOM)
5
DQS, DQS#
DQ
DI
b
DM
t
t
5
DQSS
t
WL - DQSS
DQSS (MIN)
DQS, DQS#
DQ
DI
b
DM
t
t 5
DQSS
t
WL + DQSS
DQSS (MAX)
DQS, DQS#
DQ
DI
b
DM
Transitioning Data
Don’t Care
1. Subsequent rising DQS signals must align to the clock within tDQSS.
Notes:
2. DI b = data-in for column b.
3. Three subsequent elements of data-in are applied in the programmed order following
DI b.
4. Shown with BL = 4, AL = 0, CL = 3; thus, WL = 2.
5. A10 is LOW with the WRITE command (auto precharge is disabled).
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
103
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
WRITE
Figure 58: Consecutive WRITE-to-WRITE
T0
T1
T1n
T2
T2n
T3
T3n
T4
T4n
T5
T5n
T6
CK#
CK
Command
WRITE
NOP
CCD
WRITE
NOP
NOP
NOP
NOP
t
WL = 2
WL = 2
Bank,
Bank,
Address
Col b
Col n
WL ± tDQSS
t
DQSS (NOM)
DQS, DQS#
1
1
1
DI
DI
DQ
b
n
DM
Transitioning Data
Don’t Care
1. Subsequent rising DQS signals must align to the clock within tDQSS.
Notes:
2. DI b, etc. = data-in for column b, etc.
3. Three subsequent elements of data-in are applied in the programmed order following
DI b.
4. Three subsequent elements of data-in are applied in the programmed order following
DI n.
5. Shown with BL = 4, AL = 0, CL = 3; thus, WL = 2.
6. Each WRITE command may be to any bank.
Figure 59: Nonconsecutive WRITE-to-WRITE
T0
T1
T2
T2n
T3
T3n
T4
T4n
T5
T5n
T6
T6n
CK#
CK
Command
WRITE
NOP
NOP
WRITE
NOP
NOP
NOP
WL = 2
WL = 2
Bank,
Bank,
Address
Col b
Col n
t
t
WL ± DQSS
DQSS (NOM)
DQS, DQS#
1
1
1
DI
DI
DQ
b
n
DM
Transitioning Data
Don’t Care
1. Subsequent rising DQS signals must align to the clock within tDQSS.
Notes:
2. DI b (or n), etc. = data-in for column b (or column n).
3. Three subsequent elements of data-in are applied in the programmed order following
DI b.
4. Three subsequent elements of data-in are applied in the programmed order following
DI n.
5. Shown with BL = 4, AL = 0, CL = 3; thus, WL = 2.
6. Each WRITE command may be to any bank.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
104
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
WRITE
Figure 60: WRITE Interrupted by WRITE
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9
CK#
CK
1
3
b
2
2
2
2
2
4
4
4
Valid
WRITE
a
WRITE
Command
NOP
NOP
NOP
NOP
NOP
Valid
Valid
5
5
Address
A10
Valid
Valid
6
Valid
7
7
7
7
7
DQS, DQS#
DI
DI
DI
DI
DI
DI
DI
DI
DI
DI
DI
DI
DQ
a
a + 1
a + 2
a + 3
b
b + 1
b + 2
b + 3
b + 4
b + 5
b + 6
b + 7
WL = 3
2-clock requirement
WL = 3
Transitioning Data
Don’t Care
1. BL = 8 required and auto precharge must be disabled (A10 = LOW).
Notes:
2. The NOP or COMMAND INHIBIT commands are valid. The PRECHARGE command cannot
be issued to banks used for WRITEs at T0 and T2.
3. The interrupting WRITE command must be issued exactly 2 × tCK from previous WRITE.
4. The earliest WRITE-to-PRECHARGE timing for WRITE at T0 is WL + BL/2 + tWR where tWR
starts with T7 and not T5 (because BL = 8 from MR and not the truncated length).
5. The WRITE command can be issued to any valid bank and row address (WRITE command
at T0 and T2 can be either same bank or different bank).
6. Auto precharge can be either enabled (A10 = HIGH) or disabled (A10 = LOW) by the in-
terrupting WRITE command.
7. Subsequent rising DQS signals must align to the clock within tDQSS.
8. Example shown uses AL = 0; CL = 4, BL = 8.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
105
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
WRITE
Figure 61: WRITE-to-READ
T6
T7
T8
T9
T0
T1
T2
T2n
T3
T3n
T4
T5
T9n
CK#
CK
Command
WRITE
NOP
NOP
NOP
NOP
NOP
READ
NOP
NOP
NOP
1
t
WTR
Bank a,
Col b
Bank a,
Col n
Address
t
t
WL ± DQSS
DQSS (NOM)
CL = 3
CL = 3
CL = 3
2
DQS, DQS#
DQ
DI
DI
b
DM
t
t
DQSS (MIN)
WL - DQSS
2
DQS, DQS#
DQ
DI
DI
DI
b
DM
t
t
DQSS (MAX)
WL + DQSS
2
DQS, DQS#
DQ
DI
b
DM
Transitioning Data
Don’t Care
1. tWTR is required for any READ following a WRITE to the same device, but it is not re-
quired between module ranks.
Notes:
2. Subsequent rising DQS signals must align to the clock within tDQSS.
3. DI b = data-in for column b; DO n = data-out from column n.
4. BL = 4, AL = 0, CL = 3; thus, WL = 2.
5. One subsequent element of data-in is applied in the programmed order following DI b.
6. tWTR is referenced from the first positive CK edge after the last data-in pair.
7. A10 is LOW with the WRITE command (auto precharge is disabled).
8. The number of clock cycles required to meet tWTR is either 2 or tWTR/tCK, whichever is
greater.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
106
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
WRITE
Figure 62: WRITE-to-PRECHARGE
T6
T7
T0
T1
T2
T2n
T3
T3n
T4
T5
CK#
CK
Command
WRITE
NOP
NOP
NOP
NOP
NOP
NOP
PRE
t
t
RP
WR
Bank a,
Col b
Bank,
Address
(a or all)
t
t
DQSS (NOM)
WL + DQSS
1
DQS#
DQS
DI
b
DQ
DM
t
t
DQSS (MIN)
WL - DQSS
1
DQS#
DQS
DI
b
DQ
DM
t
t
DQSS (MAX)
WL + DQSS
1
DQS#
DQS
DI
b
DQ
DM
Transitioning Data
Don’t Care
1. Subsequent rising DQS signals must align to the clock within tDQSS.
Notes:
2. DI b = data-in for column b.
3. Three subsequent elements of data-in are applied in the programmed order following
DI b.
4. BL = 4, CL = 3, AL = 0; thus, WL = 2.
5. tWR is referenced from the first positive CK edge after the last data-in pair.
6. The PRECHARGE and WRITE commands are to the same bank. However, the PRECHARGE
and WRITE commands may be to different banks, in which case tWR is not required and
the PRECHARGE command could be applied earlier.
7. A10 is LOW with the WRITE command (auto precharge is disabled).
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
107
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
WRITE
Figure 63: Bank Write – Without Auto Precharge
T1
T4
T0
T2
T3
T5
T5n
T6
T6n
T7
T8
T9
CK#
CK
t
t
t
CL
CK
CH
CKE
1
1
1
1
2
1
1
1
NOP
Command
ACT
RA
NOP
NOP
PRE
NOP
NOP
WRITE
NOP
NOP
Col n
Address
A10
All banks
One bank
RA
3
4
Bank select
Bank x
Bank x
Bank x
t
t
WR
RCD
WL = 2
t
RP
t
t
RAS
t
WL ± DQSS (NOM)
5
DQS, DQS#
t
t
t
DQSL DQSH WPST
WPRE
DI
6
DQ
n
DM
Transitioning Data
Don’t Care
1. NOP commands are shown for ease of illustration; other commands may be valid at
these times.
Notes:
2. BL = 4 and AL = 0 in the case shown.
3. Disable auto precharge.
4.
“Don’t Care” if A10 is HIGH at T9.
5. Subsequent rising DQS signals must align to the clock within tDQSS.
6. DI n = data-in for column n; subsequent elements are applied in the programmed order.
7. tDSH is applicable during tDQSS (MIN) and is referenced from CK T5 or T6.
8. tDSS is applicable during tDQSS (MAX) and is referenced from CK T6 or T7.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
108
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
WRITE
Figure 64: Bank Write – with Auto Precharge
T1
T0
T2
T3
T4
T5
T5n
T6
T6n
T7
T8
T9
CK#
CK
t
t
t
CL
CK
CH
CKE
1
1
2
1
1
1
1
1
1
NOP
Command
NOP
ACT
RA
NOP
WRITE
NOP
NOP
NOP
NOP
NOP
Col n
Address
A10
3
RA
Bank select
Bank x
Bank x
4
t
WR
RCD
WL = 2
t
RP
t
RAS
t
WL ± DQSS (NOM)
5
DQS, DQS#
t
t
t
t
DQSL DQSH WPST
WPRE
DI
6
DQ
n
DM
Transitioning Data
Don’t Care
1. NOP commands are shown for ease of illustration; other commands may be valid at
these times.
Notes:
2. BL = 4 and AL = 0 in the case shown.
3. Enable auto precharge.
4. WR is programmed via MR9–MR11 and is calculated by dividing tWR (in ns) by tCK and
rounding up to the next integer value.
5. Subsequent rising DQS signals must align to the clock within tDQSS.
6. DI n = data-in from column n; subsequent elements are applied in the programmed order.
7. tDSH is applicable during tDQSS (MIN) and is referenced from CK T5 or T6.
8. tDSS is applicable during tDQSS (MAX) and is referenced from CK T6 or T7.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
109
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
WRITE
Figure 65: WRITE – DM Operation
T9
T10
T11
T1
T0
T2
T3
T4
T5
T6 T6n T7 T7n T8
CK#
CK
t
t
CL
t
CK
CH
CKE
1
1
2
1
1
1
1
1
1
1
NOP
Command
ACT
RA
PRE
NOP
NOP
WRITE
NOP
NOP
NOP
NOP
NOP
NOP
AL = 1
WL = 2
Address
Col n
All banks
One bank
A10
RA
3
Bank select
4
Bank x
Bank x
Bank x
5
t
t
WR
RCD
t
t
RPA
RAS
t
WL ± DQSS (NOM)
6
DQS, DQS#
t
t
t
DQSL DQSH WPST
t
WPRE
7
DI
DQ
n
DM
Transitioning Data
Don’t Care
1. NOP commands are shown for ease of illustration; other commands may be valid at
these times.
Notes:
2. BL = 4, AL = 1, and WL = 2 in the case shown.
3. Disable auto precharge.
4.
“Don’t Care” if A10 is HIGH at T11.
5. tWR starts at the end of the data burst regardless of the data mask condition.
6. Subsequent rising DQS signals must align to the clock within tDQSS.
7. DI n = data-in for column n; subsequent elements are applied in the programmed order.
8. tDSH is applicable during tDQSS (MIN) and is referenced from CK T6 or T7.
9. tDSS is applicable during tDQSS (MAX) and is referenced from CK T7 or T8.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
110
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
PRECHARGE
Figure 66: Data Input Timing
T0
T1
T1n
T2
T2n
T3
T3n
T4
CK#
CK
1
2
3
1
t
2
DSS
t
t
t
t
WL - DQSS (NOM)
DSH
DSS
DSH
DQS
DQS#
t
t
t
WPST
DQSL
DQSH
t
WPRE
DI
DQ
DM
Transitioning Data
Don’t Care
1. tDSH (MIN) generally occurs during tDQSS (MIN).
2. tDSS (MIN) generally occurs during tDQSS (MAX).
Notes:
3. Subsequent rising DQS signals must align to the clock within tDQSS.
4. WRITE command issued at T0.
5. For x16, LDQS controls the lower byte and UDQS controls the upper byte.
6. WRITE command with WL = 2 (CL = 3, AL = 0) issued at T0.
PRECHARGE
Precharge can be initiated by either a manual PRECHARGE command or by an autopre-
charge in conjunction with either a READ or WRITE command. Precharge will deacti-
vate the open row in a particular bank or the open row in all banks. The PRECHARGE
operation is shown in the previous READ and WRITE operation sections.
During a manual PRECHARGE command, the A10 input determines whether one or all
banks are to be precharged. In the case where only one bank is to be precharged, bank
address inputs determine the bank to be precharged. When all banks are to be pre-
charged, the bank address inputs are treated as “Don’t Care.”
Once a bank has been precharged, it is in the idle state and must be activated prior to
any READ or WRITE commands being issued to that bank. When a single-bank PRE-
CHARGE command is issued, tRP timing applies. When the PRECHARGE (ALL) com-
mand is issued, tRPA timing applies, regardless of the number of banks opened.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
111
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
REFRESH
REFRESH
The commercial temperature DDR2 SDRAM requires REFRESH cycles at an average in-
terval of 7.8125µs (MAX) and all rows in all banks must be refreshed at least once every
64ms. The refresh period begins when the REFRESH command is registered and ends
tRFC (MIN) later. The average interval must be reduced to 3.9µs (MAX) when TC ex-
ceeds +85°C.
Figure 67: Refresh Mode
T0
T1
Ta0
Ta1
T4
T2
T3
Tb0
Tb1
Tb2
CK#
CK
t
t
t
CL
CK
CH
CKE
1
1
1
1
2
1
1
NOP
Command
NOP
PRE
NOP
NOP
REF
NOP
REF
NOP
ACT
RA
Address
A10
All banks
One bank
Bank(s)3
RA
Bank
BA
4
4
4
DQS, DQS#
DQ
DM
t
2
t
t
RP
RFC (MIN)
RFC
Indicates a break in
time scale
Don’t Care
1. NOP commands are shown for ease of illustration; other valid commands may be possi-
ble at these times. CKE must be active during clock positive transitions.
Notes:
2. The second REFRESH is not required and is only shown as an example of two back-to-
back REFRESH commands.
3.
“Don’t Care” if A10 is HIGH at this point; A10 must be HIGH if more than one bank is
active (must precharge all active banks).
4. DM, DQ, and DQS signals are all “Don’t Care”/High-Z for operations shown.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
112
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
SELF REFRESH
SELF REFRESH
The SELF REFRESH command is initiated when CKE is LOW. The differential clock
should remain stable and meet tCKE specifications at least 1 × tCK after entering self
refresh mode. The procedure for exiting self refresh requires a sequence of commands.
First, the differential clock must be stable and meet tCK specifications at least 1 × tCK
prior to CKE going back to HIGH. Once CKE is HIGH (tCKE [MIN] has been satisfied
with three clock registrations), the DDR2 SDRAM must have NOP or DESELECT com-
mands issued for tXSNR. A simple algorithm for meeting both refresh and DLL require-
ments is used to apply NOP or DESELECT commands for 200 clock cycles before
applying any other command.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
113
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
SELF REFRESH
Figure 68: Self Refresh
Tb0
Tc0
Td0
T0
T1
T2
Ta0
Ta1
Ta2
2
CK#
1
CK
t
1
t
1
CK
t
t
CL
CH
CK
t
t
3
t
ISXR
CKE
IH
1
CKE
4
4
5
5
Valid
Command
NOP
REF
NOP
NOP
Valid
t
IH
6
ODT
6
AOFD/ AOFPD
t
t
7
Address
Valid
Valid
DQS#, DQS
DQ
DM
t
2, 5, 10
XSNR
t
9
8
t
CKE (MIN)
RP
t
7
2,
XSRD
Enter self refresh
mode (synchronous)
Exit self refresh
mode (asynchronous)
Indicates a break in
time scale
Don’t Care
1. Clock must be stable and meeting tCK specifications at least 1 × tCK after entering self
refresh mode and at least 1 × tCK prior to exiting self refresh mode.
Notes:
2. Self refresh exit is asynchronous; however, tXSNR and tXSRD timing starts at the first ris-
ing clock edge where CKE HIGH satisfies tISXR.
3. CKE must stay HIGH until tXSRD is met; however, if self refresh is being re-entered, CKE
may go back LOW after tXSNR is satisfied.
4. NOP or DESELECT commands are required prior to exiting self refresh until state Tc0,
which allows any nonREAD command.
5. tXSNR is required before any nonREAD command can be applied.
6. ODT must be disabled and RTT off (tAOFD and tAOFPD have been satisfied) prior to enter-
ing self refresh at state T1.
7. tXSRD (200 cycles of CK) is required before a READ command can be applied at state Td0.
8. Device must be in the all banks idle state prior to entering self refresh mode.
9. After self refresh has been entered, tCKE (MIN) must be satisfied prior to exiting self
refresh.
10. Upon exiting SELF REFRESH, ODT must remain LOW until tXSRD is satisfied.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
114
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Power-Down Mode
Power-Down Mode
DDR2 SDRAM supports multiple power-down modes that allow significant power sav-
ings over normal operating modes. CKE is used to enter and exit different power-down
modes. Power-down entry and exit timings are shown in Figure 69 (page 116). Detailed
power-down entry conditions are shown in Figure 70 (page 118)–Figure 77 (page 121).
Table 43 (page 117) is the CKE Truth Table.
DDR2 SDRAM requires CKE to be registered HIGH (active) at all times that an access is
in progress—from the issuing of a READ or WRITE command until completion of the
burst. Thus, a clock suspend is not supported. For READs, a burst completion is defined
when the read postamble is satisfied; for WRITEs, a burst completion is defined when
the write postamble and tWR (WRITE-to-PRECHARGE command) or tWTR (WRITE-to-
READ command) are satisfied, as shown in Figure 72 (page 119) and Figure 73
(page 119) on Figure 73 (page 119). The number of clock cycles required to meet tWTR
is either two or tWTR/tCK, whichever is greater.
Power-down mode (see Figure 69 (page 116)) is entered when CKE is registered low
coincident with an NOP or DESELECT command. CKE is not allowed to go LOW during
a mode register or extended mode register command time, or while a READ or WRITE
operation is in progress. If power-down occurs when all banks are idle, this mode is
referred to as precharge power-down. If power-down occurs when there is a row active
in any bank, this mode is referred to as active power-down. Entering power-down deac-
tivates the input and output buffers, excluding CK, CK#, ODT, and CKE. For maximum
power savings, the DLL is frozen during precharge power-down. Exiting active power-
down requires the device to be at the same voltage and frequency as when it entered
power-down. Exiting precharge power-down requires the device to be at the same volt-
age as when it entered power-down; however, the clock frequency is allowed to change
(see Precharge Power-Down Clock Frequency Change (page 122)).
The maximum duration for either active or precharge power-down is limited by the re-
fresh requirements of the device tRFC (MAX). The minimum duration for power-down
entry and exit is limited by the tCKE (MIN) parameter. The following must be main-
tained while in power-down mode: CKE LOW, a stable clock signal, and stable power
supply signals at the inputs of the DDR2 SDRAM. All other input signals are “Don’t
Care” except ODT. Detailed ODT timing diagrams for different power-down modes are
shown in Figure 82 (page 127)–Figure 87 (page 131).
The power-down state is synchronously exited when CKE is registered HIGH (in con-
junction with a NOP or DESELECT command), as shown in Figure 69 (page 116).
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
115
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Power-Down Mode
Figure 69: Power-Down
T1
T2
T3
T4
T5
T6
T7
T8
CK#
CK
t
t
CL
t
CH
CK
1
Command
CKE
NOP
NOP
NOP
Valid
Valid
Valid
t
2
CKE (MIN)
t
IH
t
IH
t
2
CKE (MIN)
t
IS
Address
Valid
Valid
Valid
t
3 t 4
XP , XARD
t
5
XARDS
DQS, DQS#
DQ
DM
Enter
Exit
power-down
mode
power-down
mode
Don’t Care
6
1. If this command is a PRECHARGE (or if the device is already in the idle state), then the
power-down mode shown is precharge power-down. If this command is an ACTIVATE
(or if at least one row is already active), then the power-down mode shown is active power-
down.
Notes:
2. tCKE (MIN) of three clocks means CKE must be registered on three consecutive positive
clock edges. CKE must remain at the valid input level the entire time it takes to achieve
the three clocks of registration. Thus, after any CKE transition, CKE may not transition
from its valid level during the time period of tIS + 2 × tCK + tIH. CKE must not transition
during its tIS and tIH window.
3. tXP timing is used for exit precharge power-down and active power-down to any non-
READ command.
4. tXARD timing is used for exit active power-down to READ command if fast exit is selec-
ted via MR (bit 12 = 0).
5. tXARDS timing is used for exit active power-down to READ command if slow exit is selec-
ted via MR (bit 12 = 1).
6. No column accesses are allowed to be in progress at the time power-down is entered. If
the DLL was not in a locked state when CKE went LOW, the DLL must be reset after
exiting power-down mode for proper READ operation.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
116
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Power-Down Mode
Table 43: Truth Table – CKE
Notes 1–4 apply to the entire table
CKE
Command (n)
CS#, RAS#, CAS#,
WE#
Previous Cycle
Current
Cycle (n)
Current State
(n - 1)
Action (n)
Notes
5, 6
Power-down
L
L
L
H
L
X
Maintain power-down
Power-down exit
Maintain self refresh
Self refresh exit
DESELECT or NOP
X
7, 8
Self refresh
L
6
L
H
L
DESELECT or NOP
7, 9, 10
7, 8, 11, 12
7, 8, 11
Bank(s) active
All banks idle
H
H
DESELECT or NOP Active power-down entry
L
DESELECT or NOP Precharge power-down
entry
H
H
L
Refresh
Self refresh entry
10, 12, 13
14
H
Shown in Table 36 (page 68)
1. CKE (n) is the logic state of CKE at clock edge n; CKE (n - 1) was the state of CKE at the
Notes:
previous clock edge.
2. Current state is the state of the DDR2 SDRAM immediately prior to clock edge n.
3. Command (n) is the command registered at clock edge n, and action (n) is a result of
command (n).
4. The state of ODT does not affect the states described in this table. The ODT function is
not available during self refresh (see ODT Timing (page 125) for more details and specif-
ic restrictions).
5. Power-down modes do not perform any REFRESH operations. The duration of power-
down mode is therefore limited by the refresh requirements.
6.
“X” means “Don’t Care” (including floating around VREF) in self refresh and power-
down. However, ODT must be driven high or low in power-down if the ODT function is
enabled via EMR.
7. All states and sequences not shown are illegal or reserved unless explicitly described else-
where in this document.
8. Valid commands for power-down entry and exit are NOP and DESELECT only.
9. On self refresh exit, DESELECT or NOP commands must be issued on every clock edge
occurring during the tXSNR period. READ commands may be issued only after tXSRD
(200 clocks) is satisfied.
10. Valid commands for self refresh exit are NOP and DESELECT only.
11. Power-down and self refresh can not be entered while READ or WRITE operations,
LOAD MODE operations, or PRECHARGE operations are in progress. See SELF REFRESH
(page 113) and SELF REFRESH (page 74) for a list of detailed restrictions.
12. Minimum CKE high time is tCKE = 3 × tCK. Minimum CKE LOW time is tCKE = 3 × tCK.
This requires a minimum of 3 clock cycles of registration.
13. Self refresh mode can only be entered from the all banks idle state.
14. Must be a legal command, as defined in Table 36 (page 68).
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
117
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Power-Down Mode
Figure 70: READ-to-Power-Down or Self Refresh Entry
T0
T1
T2
T3
T4
T5
T6
T7
CK#
CK
1
NOP
Command
READ
NOP
NOP
NOP
Valid
Valid
t
CKE (MIN)
CKE
Address
Valid
A10
DQS, DQS#
DQ
DO
DO
DO
DO
RL = 3
2
Power-down or
self refresh entry
Transitioning Data
Don’t Care
1. In the example shown, READ burst completes at T5; earliest power-down or self refresh
entry is at T6.
Notes:
2. Power-down or self refresh entry may occur after the READ burst completes.
Figure 71: READ with Auto Precharge-to-Power-Down or Self Refresh Entry
T0
T1
T2
T3
T4
T5
T6
T7
CK#
CK
1
Command
NOP
READ
NOP
NOP
NOP
Valid
Valid
t
CKE (MIN)
CKE
Valid
Address
A10
DQS, DQS#
DQ
DO
DO
DO
DO
RL = 3
Power-down or
2
self refresh entry
Transitioning Data
Don’t Care
1. In the example shown, READ burst completes at T5; earliest power-down or self refresh
entry is at T6.
Notes:
2. Power-down or self refresh entry may occur after the READ burst completes.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
118
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Power-Down Mode
Figure 72: WRITE-to-Power-Down or Self Refresh Entry
T0
T1
T2
T3
T4
T5
T6
T7
T8
CK#
CK
1
NOP
Command
WRITE
NOP
NOP
NOP
Valid
Valid
Valid
t
CKE (MIN)
CKE
Address
Valid
A10
DQS, DQS#
DQ
DO
DO
DO
DO
t
WL = 3
WTR
Power-down or
self refresh entry
1
Transitioning Data
Don’t Care
1. Power-down or self refresh entry may occur after the WRITE burst completes.
Note:
Figure 73: WRITE with Auto Precharge-to-Power-Down or Self Refresh Entry
T0
T1
T2
T3
T4
T5
Ta0
Ta1
Ta2
CK#
CK
1
Command
WRITE
NOP
NOP
NOP
Valid
Valid
NOP
Valid
t
CKE (MIN)
CKE
Address
Valid
A10
DQS, DQS#
DQ
DO
DO
DO
DO
2
WL = 3
WR
Power-down or
self refresh entry
Indicates a break in
time scale
Transitioning Data
Don’t Care
1. Internal PRECHARGE occurs at Ta0 when WR has completed; power-down entry may oc-
cur 1 x tCK later at Ta1, prior to tRP being satisfied.
Notes:
2. WR is programmed through MR9–MR11 and represents (tWR [MIN] ns/tCK) rounded up
to next integer tCK.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
119
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Power-Down Mode
Figure 74: REFRESH Command-to-Power-Down Entry
T0
T1
T2
T3
CK#
CK
Valid
REFRESH
NOP
Command
t
CKE (MIN)
CKE
t
1 x CK
1
Power-down
entry
Don’t Care
1. The earliest precharge power-down entry may occur is at T2, which is 1 × tCK after the
Note:
REFRESH command. Precharge power-down entry occurs prior to tRFC (MIN) being satis-
fied.
Figure 75: ACTIVATE Command-to-Power-Down Entry
T0
T1
T2
T3
CK#
CK
Valid
ACT
NOP
Command
VALID
Address
t
CKE (MIN)
CKE
t
1
CK
1
Power-down
entry
Don’t Care
1. The earliest active power-down entry may occur is at T2, which is 1 × tCK after the ACTI-
VATE command. Active power-down entry occurs prior to tRCD (MIN) being satisfied.
Note:
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
120
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Power-Down Mode
Figure 76: PRECHARGE Command-to-Power-Down Entry
T0
T1
T2
T3
CK#
CK
Valid
PRE
NOP
Command
Valid
Address
A10
All banks
vs
Single bank
tCKE (MIN)
CKE
1 x tCK
1
Power-down
entry
Don’t Care
1. The earliest precharge power-down entry may occur is at T2, which is 1 × tCK after the
PRECHARGE command. Precharge power-down entry occurs prior to tRP (MIN) being sat-
isfied.
Note:
Figure 77: LOAD MODE Command-to-Power-Down Entry
T0
T1
T2
T3
T4
CK#
CK
Command
Valid
LM
NOP
NOP
1
Address
Valid
t
CKE (MIN)
CKE
t
2
t
MRD
RP
3
Power-down
entry
Don’t Care
1. Valid address for LM command includes MR, EMR, EMR(2), and EMR(3) registers.
2. All banks must be in the precharged state and tRP met prior to issuing LM command.
3. The earliest precharge power-down entry is at T3, which is after tMRD is satisfied.
Notes:
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
121
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Precharge Power-Down Clock Frequency Change
Precharge Power-Down Clock Frequency Change
When the DDR2 SDRAM is in precharge power-down mode, ODT must be turned off
and CKE must be at a logic LOW level. A minimum of two differential clock cycles must
pass after CKE goes LOW before clock frequency may change. The device input clock
frequency is allowed to change only within minimum and maximum operating frequen-
cies specified for the particular speed grade. During input clock frequency change, ODT
and CKE must be held at stable LOW levels. When the input clock frequency is changed,
new stable clocks must be provided to the device before precharge power-down may be
exited, and DLL must be reset via MR after precharge power-down exit. Depending on
the new clock frequency, additional LM commands might be required to adjust the CL,
WR, AL, and so forth. Depending on the new clock frequency, an additional LM com-
mand might be required to appropriately set the WR MR9, MR10, MR11. During the
DLL relock period of 200 cycles, ODT must remain off. After the DLL lock time, the
DRAM is ready to operate with a new clock frequency.
Figure 78: Input Clock Frequency Change During Precharge Power-Down Mode
Previous clock frequency
T1 T2
New clock frequency
Ta2
Ta4
Ta1
Ta3
Tb0
T0
T3
Ta0
CK#
CK
t
t
CL
t
t
CL
CH
CH
t
t
CK
CK
t
1
t
2
2 x CK (MIN)
1 x CK (MIN)
t
3
CKE (MIN)
CKE
t
3
CKE (MIN)
Command
4
NOP
NOP
NOP
LM
NOP
Valid
Valid
Valid
Address
Valid
DLL RESET
t
XP
ODT
High-Z
High-Z
DQS, DQS#
DQ
DM
Enter precharge
power-down mode
Frequency
change
Exit precharge
power-down mode
t
200 x CK
Indicates a break in
time scale
Don’t Care
1. A minimum of 2 × tCK is required after entering precharge power-down prior to chang-
ing clock frequencies.
Notes:
2. When the new clock frequency has changed and is stable, a minimum of 1 × tCK is re-
quired prior to exiting precharge power-down.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
122
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Reset
3. Minimum CKE high time is tCKE = 3 × tCK. Minimum CKE LOW time is tCKE = 3 × tCK.
This requires a minimum of three clock cycles of registration.
4. If this command is a PRECHARGE (or if the device is already in the idle state), then the
power-down mode shown is precharge power-down, which is required prior to the
clock frequency change.
Reset
CKE Low Anytime
DDR2 SDRAM applications may go into a reset state anytime during normal operation.
If an application enters a reset condition, CKE is used to ensure the DDR2 SDRAM de-
vice resumes normal operation after reinitializing. All data will be lost during a reset
condition; however, the DDR2 SDRAM device will continue to operate properly if the
following conditions outlined in this section are satisfied.
The reset condition defined here assumes all supply voltages (VDD, VDDQ, VDDL, and
VREF) are stable and meet all DC specifications prior to, during, and after the RESET op-
eration. All other input balls of the DDR2 SDRAM device are a “Don’t Care” during
RESET with the exception of CKE.
If CKE asynchronously drops LOW during any valid operation (including a READ or
WRITE burst), the memory controller must satisfy the timing parameter tDELAY before
turning off the clocks. Stable clocks must exist at the CK, CK# inputs of the DRAM be-
fore CKE is raised HIGH, at which time the normal initialization sequence must occur
(see Initialization). The DDR2 SDRAM device is now ready for normal operation after
the initialization sequence. Figure 79 (page 124) shows the proper sequence for a RE-
SET operation.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
123
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
Reset
Figure 79: RESET Function
T3
T4
T5
T0
T1
T2
Tb0
Ta0
t
CK
CK#
CK
t
CL
t
CL
t
CKE (MIN)
t
DELAY
1
CKE
ODT
2
2
2
2
Command
READ
READ
PRE
NOP
NOP
NOP
NOP
3
DM
Col n
Col n
Address
A10
All banks
Bank address
Bank a
Bank b
4
High-Z
High-Z
High-Z
High-Z
3
DQS
3
DQ
DO
DO
DO
High-Z
RTT
t
System
RESET
RPA
T = 400ns (MIN)
5
Start of normal
initialization
sequence
Indicates a break in
time scale
Unknown
RTT On
Transitioning Data
Don’t Care
1. VDD, VDDL, VDDQ, VTT, and VREF must be valid at all times.
2. Either NOP or DESELECT command may be applied.
Notes:
3. DM represents DM for x4/x8 configuration and UDM, LDM for x16 configuration. DQS
represents DQS, DQS#, UDQS, UDQS#, LDQS, LDQS#, RDQS, and RDQS# for the appropri-
ate configuration (x4, x8, x16).
4. In certain cases where a READ cycle is interrupted, CKE going HIGH may result in the
completion of the burst.
5. Initialization timing is shown in Figure 42 (page 85).
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
124
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
ODT Timing
ODT Timing
Once a 12ns delay (tMOD) has been satisfied, and after the ODT function has been ena-
bled via the EMR LOAD MODE command, ODT can be accessed under two timing
categories. ODT will operate either in synchronous mode or asynchronous mode, de-
pending on the state of CKE. ODT can switch anytime except during self refresh mode
and a few clocks after being enabled via EMR, as shown in Figure 80 (page 126).
There are two timing categories for ODT—turn-on and turn-off. During active mode
(CKE HIGH) and fast-exit power-down mode (any row of any bank open, CKE LOW,
MR[12 = 0]), tAOND, tAON, tAOFD, and tAOF timing parameters are applied, as shown
in Figure 82 (page 127).
During slow-exit power-down mode (any row of any bank open, CKE LOW, MR[12] = 1)
and precharge power-down mode (all banks/rows precharged and idle, CKE LOW),
tAONPD and tAOFPD timing parameters are applied, as shown in Figure 83 (page 128).
ODT turn-off timing, prior to entering any power-down mode, is determined by the pa-
rameter tANPD (MIN), as shown in Figure 84 (page 128). At state T2, the ODT HIGH
signal satisfies tANPD (MIN) prior to entering power-down mode at T5. When tANPD
(MIN) is satisfied, tAOFD and tAOF timing parameters apply. Figure 84 (page 128) also
shows the example where tANPD (MIN) is not satisfied because ODT HIGH does not
occur until state T3. When tANPD (MIN) is notsatisfied, tAOFPD timing parameters apply.
ODT turn-on timing prior to entering any power-down mode is determined by the pa-
rameter tANPD, as shown in Figure 85 (page 129). At state T2, the ODT HIGH signal
satisfies tANPD (MIN) prior to entering power-down mode at T5. When tANPD (MIN) is
satisfied, tAOND and tAON timing parameters apply. Figure 85 (page 129) also shows
the example where tANPD (MIN) is not satisfied because ODT HIGH does not occur
until state T3. When tANPD (MIN) is not satisfied, tAONPD timing parameters apply.
ODT turn-off timing after exiting any power-down mode is determined by the parame-
ter tAXPD (MIN), as shown in Figure 86 (page 130). At state Ta1, the ODT LOW signal
satisfies tAXPD (MIN) after exiting power-down mode at state T1. When tAXPD (MIN) is
satisfied, tAOFD and tAOF timing parameters apply. Figure 86 (page 130) also shows
the example where tAXPD (MIN) is not satisfied because ODT LOW occurs at state Ta0.
When tAXPD (MIN) is not satisfied, tAOFPD timing parameters apply.
ODT turn-on timing after exiting either slow-exit power-down mode or precharge power-
down mode is determined by the parameter tAXPD (MIN), as shown in Figure 87
(page 131). At state Ta1, the ODT HIGH signal satisfies tAXPD (MIN) after exiting power-
down mode at state T1. When tAXPD (MIN) is satisfied, tAOND and tAON timing
parameters apply. Figure 87 (page 131) also shows the example where tAXPD (MIN) is
not satisfied because ODT HIGH occurs at state Ta0. When tAXPD (MIN) is not satisfied,
tAONPD timing parameters apply.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
125
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
ODT Timing
Figure 80: ODT Timing for Entering and Exiting Power-Down Mode
Synchronous
Synchronous or
Asynchronous
Synchronous
tANPD (3 tCKs)
tAXPD (8 tCKs)
First CKE latched LOW
First CKE latched HIGH
CKE
Any mode except
self refresh mode
Any mode except
self refresh mode
Active power-down fast (synchronous)
Active power-down slow (asynchronous)
Precharge power-down (asynchronous)
Applicable modes
tAOND/tAOFD
tAOND/tAOFD
tAOND/tAOFD (synchronous)
tAONPD/tAOFPD (asynchronous)
Applicable timing parameters
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
126
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
ODT Timing
MRS Command to ODT Update Delay
During normal operation, the value of the effective termination resistance can be
changed with an EMRS set command. tMOD (MAX) updates the RTT setting.
Figure 81: Timing for MRS Command to ODT Update Delay
T0
Ta0
Ta1
Ta2
Ta3
Ta4
Ta5
1
EMRS
NOP
NOP
NOP
NOP
NOP
Command
CK#
CK
2
2
ODT
t
t
MOD
AOFD
t
IS
0ns
Internal
TT setting
Old setting
Undefined
New setting
R
Indicates a break in
time scale
1. The LM command is directed to the mode register, which updates the information in
EMR (A6, A2), that is, RTT (nominal).
Notes:
2. To prevent any impedance glitch on the channel, the following conditions must be met:
tAOFD must be met before issuing the LM command; ODT must remain LOW for the
entire duration of the tMOD window until tMOD is met.
Figure 82: ODT Timing for Active or Fast-Exit Power-Down Mode
T0
T1
T2
T3
T4
T5
T6
CK#
CK
t
t
t
CH
CL
CK
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Command
Address
CKE
t
AOND
ODT
t
AOFD
RTT
t
t
AON (MIN)
AOF (MAX)
t
AOF (MIN)
t
AON (MAX)
R
TT Unknown
RTT On
Don’t Care
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
127
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
ODT Timing
Figure 83: ODT Timing for Slow-Exit or Precharge Power-Down Modes
T0
T1
T2
T3
T4
T5
T6
T7
CK#
CK
t
t
t
CL
CK
CH
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Command
Address
CKE
ODT
t
AONPD (MAX)
t
AONPD (MIN)
RTT
t
AOFPD (MIN)
t
AOFPD (MAX)
Transitioning RTT
RTT Unknown
RTT On
Don’t Care
Figure 84: ODT Turn-Off Timings When Entering Power-Down Mode
T0
T1
T2
T3
T4
T5
T6
CK#
CK
NOP
NOP
NOP
NOP
NOP
NOP
NOP
Command
t
ANPD (MIN)
CKE
t
AOFD
ODT
RTT
t
AOF (MAX)
t
AOF (MIN)
t
AOFPD (MAX)
ODT
RTT
t
AOFPD (MIN)
Transitioning RTT
R
TT Unknown
R
TT ON
Don’t Care
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
128
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
ODT Timing
Figure 85: ODT Turn-On Timing When Entering Power-Down Mode
T0
T1
T2
T3
T4
T5
T6
CK#
CK
Command
NOP
NOP
NOP
NOP
t
NOP
NOP
NOP
ANPD (MIN)
CKE
ODT
t
t
AOND
t
AON (MAX)
RTT
AON (MIN)
ODT
RTT
t
AONPD (MAX)
t
AONPD (MIN)
Transitioning RTT
R
TT Unknown
R
TT On
Don’t Care
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
129
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
ODT Timing
Figure 86: ODT Turn-Off Timing When Exiting Power-Down Mode
T0
T1
T2
T3
T4
Ta0
Ta1
Ta2
Ta3
Ta4
Ta5
CK#
CK
NOP
NOP
NOP
NOP
NOP
NOP
NOP
NOP
NOP
NOP
NOP
Command
CKE
t
AXPD (MIN)
t
CKE (MIN)
t
AOFD
ODT
t
AOF (MAX)
R
TT
t
AOF (MIN)
t
AOFPD (MAX)
ODT
R
TT
t
AOFPD (MIN)
Indicates a break in
time scale
RTT Unknown
RTT On
Transitioning RTT
Don’t Care
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
130
© 2004 Micron Technology, Inc. All rights reserved.
1Gb: x4, x8, x16 DDR2 SDRAM
ODT Timing
Figure 87: ODT Turn-On Timing When Exiting Power-Down Mode
T0
T1
T2
T3
T4
Ta0
Ta1
Ta2
Ta3
Ta4
Ta5
CK#
CK
Command
NOP
NOP
NOP
NOP
t
NOP
NOP
NOP
NOP
NOP
NOP
NOP
AXPD (MIN)
CKE
t
CKE (MIN)
ODT
t
AOND
t
AON (MAX)
RTT
t
AON (MIN)
ODT
RTT
t
AONPD (MAX)
t
AONPD (MIN)
Indicates a break in
time scale
RTT Unknown
RTT On
Transitioning RTT
Don’t Care
8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900
www.micron.com/productsupport Customer Comment Line: 800-932-4992
Micron and the Micron logo are trademarks of Micron Technology, Inc.
All other trademarks are the property of their respective owners.
This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein.
Although considered final, these specifications are subject to change, as further product development and data characterization some-
times occur.
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. T 02/10 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
131
© 2004 Micron Technology, Inc. All rights reserved.
相关型号:
©2020 ICPDF网 联系我们和版权申明