USB2534I-1080AEN-TR [MICROCHIP]
UNIVERSAL SERIAL BUS CONTROLLER;
| 型号： | USB2534I-1080AEN-TR |
| 厂家： | 
MICROCHIP |
| 描述： | UNIVERSAL SERIAL BUS CONTROLLER 时钟 外围集成电路 |
| 文件： | 总52页 (文件大小：472K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
USB2534
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
PRODUCT FEATURES
Highlights
Additional Features
Hub Controller IC with 4 downstream ports
MultiTRAKTM
—
Dedicated Transaction Translator per port
USB-IF Battery Charger revision 1.2 support on up &
downstream ports (DCP, CDP, SDP)
PortMap
®
—
Configurable port mapping and disable sequencing
Battery charging support for Apple devices
PortSwap
FlexConnect: Downstream port 1 able to swap with
upstream port, allowing master capable devices to
control other devices on the hub
USB to I2CTM bridge endpoint support
—
Configurable differential intra-pair signal swapping
PHYBoostTM
—
Programmable USB transceiver drive strength for
recovering signal integrity
VariSenseTM
USB Link Power Management (LPM) support
SUSPEND pin for remote wakeup indication to host
Vendor Specific Messaging (VSM) support
—
Programmable USB receiver sensitivity
Low power operation
Enhanced OEM configuration options available
through a single serial I2CTM EEPROM, OTP, or
SMBus Slave Port
Full Power Management with individual or ganged
power control of each downstream port
Built-in Self-Powered or Bus-Powered internal default
settings provide flexibility in the quantity of USB
expansion ports utilized without redesign
36-pin (6x6mm) SQFN, RoHS compliant package
Footprint compatible with USB2514B
Supports “Quad Page” configuration OTP flash
Target Applications
—
Four consecutive 200 byte configuration pages
Fully integrated USB termination and Pull-up/Pull-
down resistors
LCD monitors and TVs
Multi-function USB peripherals
PC mother boards
On-chip Power On Reset (POR)
Internal 3.3V and 1.2V voltage regulators
Set-top boxes, DVD players, DVR/PVR
Printers and scanners
PC media drive bay
On Board 24MHz Crystal Driver, Resonator, or
External 24MHz clock input
Environmental
Portable hub boxes
—
Commercial temperature range support (0ºC to 70ºC)
—
Industrial temperature range support (-40ºC to 85ºC)
Mobile PC docking
Embedded systems
2014 Microchip Technology Inc.
DS00001713A-page 1
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Order Number(s):
TEMPERATURE
RANGE
ORDER NUMBER
PACKAGE TYPE
36-pin SQFN
USB2534-1080AEN (Battery Charging disabled by default)
USB2534-1050AEN (Battery Charging enabled by default)
USB2534-1080AEN-TR (Battery Charging disabled by default)
USB2534-1050AEN-TR (Battery Charging enabled by default)
USB2534i-1080AEN (Battery Charging disabled by default)
USB2534i-1050AEN (Battery Charging enabled by default)
USB2534i-1080AEN-TR (Battery Charging disabled by default)
USB2534i-1050AEN-TR (Battery Charging enabled by default)
0°C to +70°C
0°C to +70°C
-40°C to +85°C
-40°C to +85°C
36-pin SQFN
(Tape & Reel)
36-pin SQFN
36-pin SQFN
(Tape & Reel)
This product meets the halogen maximum concentration values per IEC61249-2-21
The table above represents valid part numbers at the time of printing and may not represent parts that are currently
available. For the latest list of valid ordering numbers for this product, please contact the nearest sales office.
TO OUR VALUED CUSTOMERS
It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip
products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and
enhanced as new volumes and updates are introduced.
If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via
E-mail at docerrors@microchip.com. We welcome your feedback.
Most Current Data Sheet
To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at:
http://www.microchip.com
You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page.
The last character of the literature number is the version number, (e.g., DS30000000A is version A of document DS30000000).
Errata
An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for cur-
rent devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the
revision of silicon and revision of document to which it applies.
To determine if an errata sheet exists for a particular device, please check with one of the following:
•
•
Microchip’s Worldwide Web site; http://www.microchip.com
Your local Microchip sales office (see last page)
When contacting a sales office, please specify which device, revision of silicon and data sheet (include -literature number) you are
using.
Customer Notification System
Register on our web site at www.microchip.com to receive the most current information on all of our products.
DS00001713A-page 2
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Table of Contents
Chapter 1 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.1 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chapter 2 Acronyms and Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1 Acronyms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.2 Reference Documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 3 Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1 Pin Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.2 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.3 Buffer Type Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Chapter 4 Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.1 Integrated Power Regulators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.2 Power Connection Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Chapter 5 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.1 Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.1.1 Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.1.2 Hardware Initialization Stage (HW_INIT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.1.3 Software Initialization Stage (SW_INIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.1.4 SOC Configuration Stage (SOC_CFG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.1.5 Configuration Stage (CONFIG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.1.6 Battery Charger Detection Stage (CHGDET) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.1.7 Hub Connect Stage (Hub.Connect). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.1.8 Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Chapter 6 Device Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.1 Configuration Method Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.2 Customer Accessible Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.2.1 USB Accessible Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.2.2 SMBus Accessible Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.3 Device Configuration Straps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.3.1 Non-Removable Device (NON_REM[1:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.3.2 Configuration Select (CFG_SEL[1:0]) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.3.3 Downstream Battery Charging Enable (BC_EN[4:1]) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.3.4 Port Disable (PRT_DIS_Mx/PRT_DIS_Px) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Chapter 7 Device Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
7.1 I2C Master Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
7.1.1 I2C Message Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
7.1.2 Pull-Up Resistors for I2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
7.2 SMBus Slave Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Chapter 8 Functional Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
8.1 Battery Charger Detection & Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
8.1.1 Upstream Battery Charger Detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
2014 Microchip Technology Inc.
DS00001713A-page 3
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
8.1.2 Downstream Battery Charging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
8.2 Flex Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
8.2.1 Port Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
8.3 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
8.3.1 Power-On Reset (POR). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
8.3.2 External Chip Reset (RESET_N). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
8.3.3 USB Bus Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
8.4 Link Power Management (LPM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
8.5 Remote Wakeup Indicator (SUSP_IND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
8.5.1 Normal Resume Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
8.5.2 Modified Resume Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
8.6 High Speed Indicator (HS_IND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Chapter 9 Operational Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
9.1 Absolute Maximum Ratings* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
9.2 Operating Conditions** . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
9.3 Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
9.3.1 Operational / Unconfigured . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
9.3.2 Suspend / Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
9.4 DC Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
9.5 AC Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
9.5.1 Power-On Configuration Strap Valid Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
9.5.2 Reset and Configuration Strap Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
9.5.3 USB Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
9.5.4 SMBus Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
9.5.5 I2C Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
9.6 Clock Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
9.6.1 Oscillator/Crystal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
9.6.2 External Reference Clock (REFCLK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Chapter 10 Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Chapter 11 Datasheet Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
DS00001713A-page 4
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
List of Figures
Figure 1.1 System Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 3.1 36-SQFN Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 4.1 Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 5.1 Hub Operational Mode Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 7.1 I2C Sequential Access Write Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 7.2 I2C Sequential Access Read Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 8.1 Battery Charging External Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 9.1 Supply Rise Time Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 9.2 Power-On Configuration Strap Valid Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Figure 9.3 RESET_N Configuration Strap Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Figure 10.1 36-SQFN Package Drawing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
2014 Microchip Technology Inc.
DS00001713A-page 5
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
List of Tables
Table 3.1 Pin Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Table 3.2 36-SQFN Package Pin Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Table 3.3 Buffer Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 6.1 Hub Configuration Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Table 6.2 NON_REM[1:0] Configuration Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Table 6.3 PRT_DIS_Mx/PRT_DIS_Px Configuration Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 8.1 Chargers Compatible with Upstream Detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Table 8.2 Downstream Port Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Table 8.3 LPM State Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Table 9.1 Operational/Unconfigured Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 9.2 Suspend/Standby Power Consumption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 9.3 DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Table 9.4 Power-On Configuration Strap Valid Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table 9.5 RESET_N Configuration Strap Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table 9.6 Crystal Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Table 11.1 Revision History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
DS00001713A-page 6
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Chapter 1 General Description
The USB2534 is a low-power, OEM configurable, MTT (Multi-Transaction Translator) USB 2.0 hub
controller with 4 downstream ports and advanced features for embedded USB applications. The
USB2534 is fully compliant with the USB 2.0 Specification, USB 2.0 Link Power Management
Addendum and will attach to an upstream port as a Full-Speed hub or as a Full-/Hi-Speed hub. The
4-port hub supports Low-Speed, Full-Speed, and Hi-Speed (if operating as a Hi-Speed hub)
downstream devices on all of the enabled downstream ports.
The USB2534 has been specifically optimized for embedded systems where high performance, and
minimal BOM costs are critical design requirements. Standby mode power has been minimized and
reference clock inputs can be aligned to the customer’s specific application. Additionally, all required
resistors on the USB ports are integrated into the hub, including all series termination and pull-up/pull-
down resistors on the D+ and D– pins.
The USB2534 supports both upstream battery charger detection and downstream battery charging.
The USB2534 integrated battery charger detection circuitry supports the USB-IF Battery Charging
(BC1.2) detection method and most Apple devices. These circuits are used to detect the attachment
and type of a USB charger and provide an interrupt output to indicate charger information is available
to be read from the device’s status registers via the serial interface. The USB2534 provides the battery
charging handshake and supports the following USB-IF BC1.2 charging profiles:
DCP: Dedicated Charging Port (Power brick with no data)
CDP: Charging Downstream Port (1.5A with data)
SDP: Standard Downstream Port (0.5A with data)
Custom profiles loaded via SMBus or OTP
The USB2534 provides an additional USB endpoint dedicated for use as a USB to I2C interface,
allowing external circuits or devices to be monitored, controlled, or configured via the USB interface.
Additionally, the USB2534 includes many powerful and unique features such as:
FlexConnect, which provides flexible connectivity options. The USB2534’s downstream port 1 can be
swapped with the upstream port, allowing master capable devices to control other devices on the hub.
MultiTRAKTM Technology, which utilizes a dedicated Transaction Translator (TT) per port to maintain
consistent full-speed data throughput regardless of the number of active downstream connections.
MultiTRAKTM outperforms conventional USB 2.0 hubs with a single TT in USB full-speed data transfers.
PortMap, which provides flexible port mapping and disable sequences. The downstream ports of a
USB2534 hub can be reordered or disabled in any sequence to support multiple platform designs with
minimum effort. For any port that is disabled, the USB2534 hub controllers automatically reorder the
remaining ports to match the USB host controller’s port numbering scheme.
PortSwap, which adds per-port programmability to USB differential-pair pin locations. PortSwap allows
direct alignment of USB signals (D+/D-) to connectors to avoid uneven trace length or crossing of the
USB differential signals on the PCB.
PHYBoost, which provides programmable levels of Hi-Speed USB
signal drive strength in the downstream port transceivers. PHYBoost
attempts to restore USB signal integrity in a compromised system
environment. The graphic on the right shows an example of Hi-
Speed USB eye diagrams before and after PHYBoost signal integrity
restoration.
VariSense, which controls the USB receiver sensitivity enabling programmable levels of USB signal
receive sensitivity. This capability allows operation in a sub-optimal system environment, such as when
a captive USB cable is used.
The USB2534 is available in commercial (0°C to +70°C) and industrial (-40°C to +85°C) temperature
range versions.
2014 Microchip Technology Inc.
DS00001713A-page 7
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
1.1
Block Diagram
Figure 1.1 details the internal block diagram of the USB2534.
Up or
Downstream
To I2C Master/Slave
SDA SCL
VDDA33
VDDA33
USB
RESET_N
VDDA33
VDDCR12
Serial
Interface
1.2V Reg
3.3V Reg
Flex PHY
Repeater
SIE
Controller
TT #1 TT #2 TT #3 TT #4 TT #5 Port Controller
2KB
UDC
Port Power
OCS
Bridge
Routing & Port Re-Ordering Logic
DP
20
SRAM
GPIO
GPIO
256B
IRAM
8051
Controller
Swap PHY
PHY
PHY
PHY
2KB
OTP
4KB
SRAM ROM
32KB
USB
USB
USB
USB
Down or Downstream Downstream Downstream
Upstream
Figure 1.1 System Block Diagram
DS00001713A-page 8
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Chapter 2 Acronyms and Definitions
2.1
Acronyms
EOP: End of Packet
EP:
FS:
Endpoint
Full-Speed
GPIO: General Purpose I/O (that is input/output to/from the device)
HS: Hi-Speed
HSOS: High Speed Over Sampling
I2C®: Inter-Integrated Circuit
LS:
Low-Speed
OTP: One Time Programmable
PCB: Printed Circuit Board
PCS: Physical Coding Sublayer
PHY: Physical Layer
SMBus: System Management Bus
UUID: Universally Unique IDentification
2.2
Reference Documents
1. UNICODE UTF-16LE For String Descriptors USB Engineering Change Notice, December 29th,
2004, http://www.usb.org
2. Universal Serial Bus Specification, Revision 2.0, April 27th, 2000, http://www.usb.org
3. Battery Charging Specification, Revision 1.2, Dec. 07, 2010, http://www.usb.org
4. I2C-Bus Specification, Version 1.1, http://www.nxp.com
5. System Management Bus Specification, Version 1.0, http://smbus.org/specs
2014 Microchip Technology Inc.
DS00001713A-page 9
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Chapter 3 Pin Descriptions
SUSP_IND/LOCAL_PWR/NON_REM0
28
29
30
31
32
33
34
35
36
18
17
16
15
14
13
12
11
10
PRTPWR3/PRTCTL3/BC_EN3
VDDA33
FLEX_USBUP_DM
FLEX_USBUP_DP
XTAL2
OCS2_N
PRTPWR2/PRTCTL2/BC_EN2
VDD33
USB2534
(Top View)
VDDCR12
XTAL1/REFCLK
NC
OCS1_N
PRTPWR1/PRTCTL1/BC_EN1
Ground Pad
(must be connected to VSS)
RBIAS
LED0
VDDA33
VDDA33
Indicates pins on the bottom of the device.
Figure 3.1 36-SQFN Pin Assignments
DS00001713A-page 10
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
3.1
Pin Descriptions
This section provides a detailed description of each pin. The signals are arranged in functional groups
according to their associated interface.
The “_N” symbol in the signal name indicates that the active, or asserted, state occurs when the signal
is at a low voltage level. For example, RESET_N indicates that the reset signal is active low. When
“_N” is not present after the signal name, the signal is asserted when at the high voltage level.
The terms assertion and negation are used exclusively. This is done to avoid confusion when working
with a mixture of “active low” and “active high” signals. The term assert, or assertion, indicates that a
signal is active, independent of whether that level is represented by a high or low voltage. The term
negate, or negation, indicates that a signal is inactive.
Note: The buffer type for each signal is indicated in the BUFFER TYPE column of Table 3.1. A
description of the buffer types is provided in Section 3.3.
Note: Compatibility with the UCS100x family of USB port power controllers requires the UCS100x be
connected on Port 1 of the USB2534. Additionally, both PRTPWR1 and OCS1_N must be
pulled high at Power-On Reset (POR).
Table 3.1 Pin Descriptions
BUFFER
TYPE
NUM PINS
NAME
SYMBOL
DESCRIPTION
USB/HSIC INTERFACES
FLEX_USBUP_DP
FLEX_USBUP_DM
SWAP_USBDN1_DP
Upstream
USB D+
(Flex Port 0)
AIO
AIO
AIO
IS
Upstream USB Port 0 D+ data signal.
Note:
The upstream Port 0 signals can be
optionally swapped with the
downstream Port 1 signals.
1
1
Upstream
USB D-
(Flex Port 0)
Upstream USB Port 0 D- data signal.
Note:
The upstream Port 0 signals can be
optionally swapped with the
downstream Port 1 signals.
Downstream
USB D+
(Swap Port 1)
Downstream USB Port 1 D+ data signal.
Note:
The downstream Port 1 signals can be
optionally swapped with the upstream
Port 0 signals.
Port 1 D+
Disable
Configuration
Strap
PRT_DIS_P1
This strap is used in conjunction with
PRT_DIS_M1 to disable USB Port 1.
1
0 = Port 1 D+ Enabled
1 = Port 1 D+ Disabled
Note:
Both PRT_DIS_P1 and PRT_DIS_M1
must be tied to VDD33 at reset to
disable the associated port.
See Note 3.4 for more information on
configuration straps.
2014 Microchip Technology Inc.
DS00001713A-page 11
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Table 3.1 Pin Descriptions (continued)
BUFFER
NUM PINS
NAME
SYMBOL
TYPE
DESCRIPTION
SWAP_USBDN1_DM
Downstream
USB D-
(Swap Port 1)
AIO
Downstream USB Port 1 D- data signal.
Note:
The downstream Port 1 signals can be
optionally swapped with the upstream
Port 0 signals.
Port 1 D-
Disable
Configuration
Strap
PRT_DIS_M1
IS
This strap is used in conjunction with
PRT_DIS_P1 to disable USB Port 1.
1
0 = Port 1 D- Enabled
1 = Port 1 D- Disabled
Note:
Both PRT_DIS_P1 and PRT_DIS_M1
must be tied to VDD33 at reset to
disable the associated port.
See Note 3.4 for more information on
configuration straps.
Downstream
USB D+
(Port 2)
USBDN2_DP
PRT_DIS_P2
AIO
IS
Downstream USB Port 2 D+ data signal.
Port 2 D+
Disable
This strap is used in conjunction with
PRT_DIS_M2 to disable USB Port 2.
Configuration
Strap
0 = Port 2 D+ Enabled
1 = Port 2 D+ Disabled
1
Note:
Both PRT_DIS_P2 and PRT_DIS_M2
must be tied to VDD33 at reset to
disable the associated port.
See Note 3.4 for more information on
configuration straps.
Downstream
USB D-
(Port 2)
USBDN2_DM
PRT_DIS_M2
AIO
IS
Downstream USB Port 2 D- data signal.
Port 2 D-
Disable
This strap is used in conjunction with
PRT_DIS_P2 to disable USB Port 2.
Configuration
0 = Port 2 D- Enabled
1 = Port 2 D- Disabled
1
Strap
Note:
Both PRT_DIS_P2 and PRT_DIS_M2
must be tied to VDD33 at reset to
disable the associated port.
See Note 3.4 for more information on
configuration straps.
DS00001713A-page 12
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Table 3.1 Pin Descriptions (continued)
BUFFER
NUM PINS
NAME
SYMBOL
TYPE
DESCRIPTION
Downstream
USB D+
USBDN3_DP
AIO
Downstream USB Port 3 D+ data signal.
(Port 3)
Port 3 D+
Disable
PRT_DIS_P3
IS
This strap is used in conjunction with
PRT_DIS_M3 to disable USB Port 3.
Configuration
Strap
0 = Port 3 D+ Enabled
1 = Port 3 D+ Disabled
1
Note:
Both PRT_DIS_P3 and PRT_DIS_M3
must be tied to VDD33 at reset to
disable the associated port.
See Note 3.4 for more information on
configuration straps.
Downstream
USB D-
(Port 3)
USBDN3_DM
PRT_DIS_M3
AIO
IS
Downstream USB Port 3 D- data signal.
Port 3 D-
Disable
This strap is used in conjunction with
PRT_DIS_P3 to disable USB Port 3.
Configuration
0 = Port 3 D- Enabled
1 = Port 3 D- Disabled
1
Strap
Note:
Both PRT_DIS_P3 and PRT_DIS_M3
must be tied to VDD33 at reset to
disable the associated port.
See Note 3.4 for more information on
configuration straps.
Downstream
USB D+
(Port 4)
USBDN4_DP
PRT_DIS_P4
AIO
IS
Downstream USB Port 4 D+ data signal.
Port 4 D+
Disable
This strap is used in conjunction with
PRT_DIS_M4 to disable USB Port 4.
Configuration
Strap
0 = Port 4 D+ Enabled
1 = Port 4 D+ Disabled
1
Note:
Both PRT_DIS_P4 and PRT_DIS_M4
must be tied to VDD33 at reset to
disable the associated port.
See Note 3.4 for more information on
configuration straps.
2014 Microchip Technology Inc.
DS00001713A-page 13
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Table 3.1 Pin Descriptions (continued)
BUFFER
NUM PINS
NAME
SYMBOL
TYPE
DESCRIPTION
Downstream
USB D-
USBDN4_DM
AIO
Downstream USB Port 4 D- data signal.
(Port 4)
Port 4 D-
Disable
PRT_DIS_M4
IS
This strap is used in conjunction with
PRT_DIS_P4 to disable USB Port 4.
Configuration
Strap
0 = Port 4 D- Enabled
1 = Port 4 D- Disabled
1
Note:
Both PRT_DIS_P4 and PRT_DIS_M4
must be tied to VDD33 at reset to
disable the associated port.
See Note 3.4 for more information on
configuration straps.
I2C/SMBUS INTERFACE
I2C Serial
SCL
I_SMB
I2C serial clock input
Clock Input
SMBus Clock
SMBCLK
I_SMB
I_SMB
SMBus serial clock input
Configuration
Select 0
Configuration
Strap
CFG_SEL0
This strap is used in conjunction with CFG_SEL1
to set the hub configuration method. Refer to
Section 6.3.2, "Configuration Select
(CFG_SEL[1:0])," on page 30 for additional
information.
1
See Note 3.4 for more information on
configuration straps.
I2C Serial
Data
SDA
IS/OD8
IS/OD8
IS
I2C bidirectional serial data
SMBus Serial
Data
SMBDATA
SMBus bidirectional serial data
Non-
Removable
Device 1
Configuration
Strap
NON_REM1
(Note 3.3)
This strap is used in conjunction with
NON_REM0 to configure the downstream ports
as non-removable devices. Refer to Section
6.3.1, "Non-Removable Device
(NON_REM[1:0])," on page 30 for additional
information.
1
See Note 3.4 for more information on
configuration straps.
MISC.
Port 1 Over-
Current
Sense Input
OCS1_N
OCS2_N
IS
(PU)
This active-low signal is input from an external
current monitor to indicate an over-current
condition on USB Port 1.
1
1
Port 2 Over-
Current
Sense Input
IS
(PU)
This active-low signal is input from an external
current monitor to indicate an over-current
condition on USB Port 2.
DS00001713A-page 14
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Table 3.1 Pin Descriptions (continued)
BUFFER
NUM PINS
NAME
SYMBOL
TYPE
DESCRIPTION
UART
UART_RX
IS
Internal UART receive input
Receive Input
Note:
This is a 3.3V signal. For RS232
operation, an external 12V translator is
required.
1
Port 3 Over-
Current
Sense Input
OCS3_N
IS
(PU)
This active-low signal is input from an external
current monitor to indicate an over-current
condition on USB Port 3.
UART
Transmit
Output
UART_TX
O8
Internal UART transmit output
Note:
This is a 3.3V signal. For RS232
operation, an external 12V driver is
required.
1
Port 4 Over-
Current
Sense Input
OCS4_N
IS
(PU)
This active-low signal is input from an external
current monitor to indicate an over-current
condition on USB Port 4.
SystemReset
Input
RESET_N
I_RST
This active-low signal allows external hardware to
reset the device.
Note:
The active-low pulse must be at least
5us wide. Refer to Section 8.3.2,
"External Chip Reset (RESET_N)," on
page 37 for additional information.
1
1
Crystal Input
XTAL1
ICLK
ICLK
External 24 MHz crystal input
Reference
Clock Input
REFCLK
Reference clock input. The device may be
alternatively driven by a single-ended clock
oscillator. When this method is used, XTAL2
should be left unconnected.
Crystal
Output
XTAL2
RBIAS
OCLK
AI
External 24 MHz crystal output
1
1
External USB
Transceiver
Bias Resistor
A 12.0kΩ (+/- 1%) resistor is attached from
ground to this pin to set the transceiver’s internal
bias settings.
LED 0 Output
LED0
O8
General purpose LED 0 output that is
configurable to blink or “breathe” at various rates.
1
Note:
LED0 must be enabled via the Protouch
configuration tool.
2014 Microchip Technology Inc.
DS00001713A-page 15
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Table 3.1 Pin Descriptions (continued)
BUFFER
NUM PINS
NAME
SYMBOL
TYPE
DESCRIPTION
Detect
VBUS_DET
IS
Detects state of upstream bus power.
Upstream
VBUS Power
When designing a detachable hub, this pin must
be connected to the VBUS power pin of the
upstream USB port through a resistor divider
(50kΩ by 100kΩ) to provide 3.3V.
For self-powered applications with a permanently
attached host, this pin must be connected to
either 3.3V or 5.0V through a resistor divider to
provide 3.3V.
1
In embedded applications, VBUS_DET may be
controlled (toggled) when the host desires to
renegotiate a connection without requiring a full
reset of the device.
Remote
Wakeup
Indicator
SUSP_IND
OD8
Configurable sideband signal used to indicate
Suspend status (default) or Remote Wakeup
events to the Host.
Suspend Indicator (default configuration):
0 = Unconfigured, or configured and in USB
suspend mode
1 = Device is configured and is active
(i.e., not in suspend)
For Remote Wakeup Indicator mode:
Refer to Section 8.5, "Remote Wakeup Indicator
(SUSP_IND)," on page 38.
Refer to Section 6.3.1, "Non-Removable Device
(NON_REM[1:0])," on page 30 for information on
LED polarity when using this signal.
1
Local Power
Detect
LOCAL_PWR
IS
Detects the availability of a local self-power
source.
0 = Self/local power source is NOT available.
(i.e., device must obtain all power from upstream
USB VBUS)
1 = Self/local power source is available
See Note 3.2 for more information on this pin.
Non-
Removable
Device 0
Configuration
Strap
NON_REM0
(Note 3.3)
IS
This strap is used in conjunction with
NON_REM1 to configure the downstream ports
as non-removable devices. Refer to Section
6.3.1, "Non-Removable Device
(NON_REM[1:0])," on page 30 for additional
information.
See Note 3.4 for more information on
configuration straps.
DS00001713A-page 16
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Table 3.1 Pin Descriptions (continued)
BUFFER
NUM PINS
NAME
SYMBOL
TYPE
DESCRIPTION
High Speed
Indicator
HS_IND
O8
Indicates a high speed connection on the
upstream port. The active state of the LED will be
determined as follows:
If CFG_SEL1 = 0, HS_IND is active high.
If CFG_SEL1 = 1, HS_IND is active low.
Asserted = hub is connected at high speed
Negated = Hub is connected at full speed
1
Configuration
Select 1
Configuration
Strap
CFG_SEL1
IS
This strap is used in conjunction with CFG_SEL0
to set the hub configuration method. Refer to
Section 6.3.2, "Configuration Select
(CFG_SEL[1:0])," on page 30 for additional
information.
See Note 3.4 for more information on
configuration straps.
Port 1 Power
Output
PRTPWR1
PRTCTL1
BC_EN1
O8
Enables power to a downstream USB device
attached to Port 1.
0 = Power disabled on downstream Port 1
1 = Power enabled on downstream Port 1
Port 1 Control
OD8/IS
(PU)
When configured as PRTCTL1, this pin functions
as both the Port 1 power enable output
(PRTPWR1) and the Port 1 over-current sense
input (OCS1_N). Refer to the PRTPWR1 and
OCS1_N descriptions for additional information.
1
Port 1 Battery
Charging
Configuration
Strap
IS
This strap is used to indicate support of the
battery charging protocol on Port 1. Enabling
battery charging support allows a device on the
port to draw currents per the USB battery
charging specification.
0 = Battery charging is not supported on Port 1
1 = Battery charging is supported on Port 1
See Note 3.4 for more information on
configuration straps.
2014 Microchip Technology Inc.
DS00001713A-page 17
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Table 3.1 Pin Descriptions (continued)
BUFFER
NUM PINS
NAME
SYMBOL
TYPE
DESCRIPTION
Port 2 Power
Output
PRTPWR2
O8
Enables power to a downstream USB device
attached to Port 2.
0 = Power disabled on downstream Port 2
1 = Power enabled on downstream Port 2
Port 2 Control
PRTCTL2
BC_EN2
OD8/IS
(PU)
When configured as PRTCTL2, this pin functions
as both the Port 2 power enable output
(PRTPWR2) and the Port 2 over-current sense
input (OCS2_N). Refer to the PRTPWR2 and
OCS2_N descriptions for additional information.
1
Port 2 Battery
Charging
Configuration
IS
This strap is used to indicate support of the
battery charging protocol on Port 2. Enabling
battery charging support allows a device on the
port to draw currents per the USB battery
charging specification.
Strap
0 = Battery charging is not supported on Port 2
1 = Battery charging is supported on Port 2
See Note 3.4 for more information on
configuration straps.
Port 3 Power
Output
PRTPWR3
PRTCTL3
BC_EN3
O8
Enables power to a downstream USB device
attached to Port 3.
0 = Power disabled on downstream Port 3
1 = Power enabled on downstream Port 3
Port 3 Control
OD8/IS
(PU)
When configured as PRTCTL3, this pin functions
as both the Port 3 power enable output
(PRTPWR3) and the Port 3 over-current sense
input (OCS3_N). Refer to the PRTPWR3 and
OCS3_N descriptions for additional information.
1
Port 3 Battery
Charging
Configuration
IS
This strap is used to indicate support of the
battery charging protocol on Port 3. Enabling
battery charging support allows a device on the
port to draw currents per the USB battery
charging specification.
Strap
0 = Battery charging is not supported on Port 3
1 = Battery charging is supported on Port 3
See Note 3.4 for more information on
configuration straps.
DS00001713A-page 18
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Table 3.1 Pin Descriptions (continued)
BUFFER
NUM PINS
NAME
SYMBOL
TYPE
DESCRIPTION
Port 4 Power
Output
PRTPWR4
O8
Enables power to a downstream USB device
attached to Port 4.
0 = Power disabled on downstream Port 4
1 = Power enabled on downstream Port 4
Port 4 Control
PRTCTL4
BC_EN4
OD8/IS
(PU)
When configured as PRTCTL4, this pin functions
as both the Port 4 power enable output
(PRTPWR4) and the Port 4 over-current sense
input (OCS4_N). Refer to the PRTPWR4 and
OCS4_N descriptions for additional information.
1
Port 4 Battery
Charging
Configuration
IS
This strap is used to indicate support of the
battery charging protocol on Port 4. Enabling
battery charging support allows a device on the
port to draw currents per the USB battery
charging specification.
Strap
0 = Battery charging is not supported on Port 4
1 = Battery charging is supported on Port 4
See Note 3.4 for more information on
configuration straps.
No Connect
NC
-
These pins must be left floating for normal device
operation.
2
POWER
+3.3V Analog
Power Supply
VDDA33
VDD33
P
+3.3V analog power supply. Refer to Chapter 4,
"Power Connections," on page 22 for power
connection information.
3
2
+3.3V Power
Supply
P
P
+3.3V power supply. These pins must be
connected to VDDA33. Refer to Chapter 4,
"Power Connections," on page 22 for power
connection information.
+1.2V Core
Power Supply
VDDCR12
+1.2V core power supply. A 1.0 μF (<1 Ω ESR)
capacitor to ground is required for regulator
stability. The capacitor should be placed as close
as possible to the device. Refer to Chapter 4,
"Power Connections," on page 22 for power
connection information.
1
Exposed
Pad on
Ground
VSS
P
Common ground. This exposed pad must be
connected to the ground plane with a via array.
package
bottom
(Figure 3.1)
Note 3.2 The LOCAL_PWR pin is sampled during the configuration state, immediately after negation
of reset, to determine whether the device is bus-powered or self-powered. When
configuration is complete, the latched value will not change until the next reset assertion.
To enable dynamic local power switching, the DYNAMIC_POWER register at location
0x4134 must be programmed with 0x41. If dynamic power switching is not required, the
DYNAMIC_POWER register should be left at the default value of 0xC1. Programming may
be performed through the SMBus interface, or permanently via OTP. Refer to the Protouch
MPT User Manual for additional information.
2014 Microchip Technology Inc.
DS00001713A-page 19
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Note 3.3 If using the local power detect function (LOCAL_PWR pin), the NON_REM[1:0]
configuration straps cannot be used to configure the non-removable state of the USB ports.
In this case, the non-removable state of the ports must be configured in internal device
registers via the Protouch tool or SMBus.
Note 3.4 Configuration strap values are latched on Power-On Reset (POR) and the rising edge of
RESET_N (external chip reset). Configuration straps are identified by an underlined
symbol name. Signals that function as configuration straps must be augmented with an
external resistor when connected to a load. Refer to Section 6.3, "Device Configuration
Straps," on page 29 for additional information.
3.2
Pin Assignments
Table 3.2 36-SQFN Package Pin Assignments
PIN
NUM
PIN
NUM
PIN NAME
PIN NAME
1
2
SWAP_USBDN1_DM/PRT_DIS_M1
SWAP_USBDN1_DP/PRT_DIS_P1
USBDN2_DM/PRT_DIS_M2
USBDN2_DP/PRT_DIS_P2
NC
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
UART_RX/OCS3_N
PRTPWR4/PRTCTL4/BC_EN4NC
UART_TX/OCS4_N
SDA/SMBDATA/NON_REM1
VDD33
3
4
5
6
USBDN3_DM/PRT_DIS_M3
USBDN3_DP/PRT_DIS_P3
USBDN4_DM/PRT_DIS_M4
USBDN4_DP/PRT_DIS_P4
VDDA33
SCL/SMBCLK/CFG_SEL0
HS_IND/CFG_SEL1
RESET_N
7
8
9
VBUS_DET
10
11
12
13
14
15
16
17
18
SUSP_IND/LOCAL_PWR/NON_REM0
VDDA33
LED0
PRTPWR1/PRTCTL1/BC_EN1
OCS1_N
FLEX_USBUP_DM
FLEX_USBUP_DP
XTAL2
VDDCR12
VDD33
XTAL1/REFCLK
NC
PRTPWR2/PRTCTL2/BC_EN2
OCS2_N
RBIAS
PRTPWR3/PRTCTL3/BC_EN3
VDDA33
DS00001713A-page 20
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
3.3
Buffer Type Descriptions
Table 3.3 Buffer Types
DESCRIPTION
BUFFER TYPE
IS
I_RST
I_SMB
O8
Schmitt-triggered input
Reset Input
I2C/SMBus Clock Input
Output with 8 mA sink and 8 mA source
Open-drain output with 8 mA sink
Open-drain output with 12 mA sink
OD8
OD12
PU
50 µA (typical) internal pull-up. Unless otherwise noted in the pin description, internal pull-
ups are always enabled.
Note:
Internal pull-up resistors prevent unconnected inputs from floating. Do not rely on
internal resistors to drive signals external to the device. When connected to a load
that must be pulled high, an external resistor must be added.
PD
50 µA (typical) internal pull-down. Unless otherwise noted in the pin description, internal
pull-downs are always enabled.
Note:
Internal pull-down resistors prevent unconnected inputs from floating. Do not rely
on internal resistors to drive signals external to the device. When connected to a
load that must be pulled low, an external resistor must be added.
AIO
ICLK
OCLK
P
Analog bi-directional
Crystal oscillator input pin
Crystal oscillator output pin
Power pin
2014 Microchip Technology Inc.
DS00001713A-page 21
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Chapter 4 Power Connections
4.1
Integrated Power Regulators
The integrated 3.3V and 1.2V power regulators allow the device to be supplied via a single 3.3V
external power supply.
The regulators are controlled by RESET_N. When RESET_N is brought high, the 3.3V regulator will
turn on. When RESET_N is brought low the 3.3V regulator will turn off.
4.2
Power Connection Diagrams
Figure 4.1 illustrates the power connections for the USB2534.
Single Supply Application
3.3V Internal
Logic
1.2V
Core Logic
3.3V I/O
+3.3V
Supply
1.2V Regulator
3.3V Regulator
VDDA33
VSS
(IN)
(OUT)
(IN)
(OUT)
(Bypass)
VDD33
USB2534
(2x)
VDDA33
VDDA33
VDDCR12
1.0uF
Figure 4.1 Power Connections
DS00001713A-page 22
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Chapter 5 Modes of Operation
The device provides two main modes of operation: Standby Mode and Hub Mode. The operating mode
of the device is selected by setting values on primary inputs according to the table below.
Table 5.1 Controlling Modes of Operation
RESET_N
INPUT
RESULTING
MODE
SUMMARY
0
Standby
Lowest Power Mode: No functions are active other than monitoring the
RESET_N input. All port interfaces are high impedance. All regulators are
powered off.
1
Hub
Full Feature Mode: Device operates as a configurable USB hub with battery
charger detection. Power consumption is based on the number of active ports,
their speed, and amount of data transferred.
Note: Refer to Section 8.3.2, "External Chip Reset (RESET_N)," on page 37 for additional information
on RESET_N.
The flowchart in Figure 5.1 shows the modes of operation. It also shows how the device traverses
through the Hub mode stages (shown in bold.) The flow of control is dictated by control register bits
shown in italics as well as other events such as availability of a reference clock. The remaining sections
in this chapter provide more detail on each stage and mode of operation.
2014 Microchip Technology Inc.
DS00001713A-page 23
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
(HW_INIT)
(SW_INIT)
Run from
Internal ROM
CFG_SEL[1:0] = 11b
NO
YES
YES
SMBus or I2C
Present?
NO
Config Load
From I2C
Do SMBus or I2C
Initialization
Config Load
From Internal ROM
NO
SOC Done?
YES
Combine OTP
Config Data
(SOC_CFG)
(CONFIG)
SW Upstream
BC detection
(CHGDET)
Hub Connect
(Hub.Connect)
Normal
operation
Figure 5.1 Hub Operational Mode Flowchart
DS00001713A-page 24
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
5.1
Boot Sequence
5.1.1
Standby Mode
If the external hardware reset is asserted, the hub will be in Standby Mode. This mode provides a very
low power state for maximum power efficiency when no signaling is required. This is the lowest power
state. In Standby Mode all internal regulators are powered off, the PLL is not running, and core logic
is powered down in order to minimize power consumption. Because core logic is powered off, no
configuration settings are retained in this mode and must be re-initialized after RESET_N is negated
high.
5.1.2
Hardware Initialization Stage (HW_INIT)
The first stage is the initialization stage and occurs on the negation of RESET_N. In this stage the
1.2V regulator is enabled and stabilizes, internal logic is reset, and the PLL locks if a valid REFCLK
is supplied. Configuration registers are initialized to their default state and strap input values are
latched. The device will complete initialization and automatically enter the next stage. Because the
digital logic within the device is not yet stable, no communication with the device using the SMBus is
possible. Configuration registers are initialized to their default state.
If there is a REFCLK present, the next state is SW_INIT.
5.1.3
Software Initialization Stage (SW_INIT)
Once the hardware is initialized, the firmware can begin to execute from the internal ROM. The
firmware checks the CFG_SEL[1:0] configuration strap values to determine if it is configured for I2C
Master loading. If so, the configuration is loaded from an external I2C ROM in the device’s CONFIG
state.
For all other configurations, the firmware checks for the presence of an external I2C/SMBus. It does
this by asserting two pull down resistors on the data and clock lines of the bus. The pull downs are
typically 50Kohm. If there are 10Kohm pull-ups present, the device becomes aware of the presence
of an external SMBus/I2C bus. If a bus is detected, the firmware transitions to the SOC_CFG state.
5.1.4
5.1.5
SOC Configuration Stage (SOC_CFG)
In this stage, the SOC may modify any of the default configuration settings specified in the integrated
ROM such as USB device descriptors, or port electrical settings, and control features such as
upstream battery charging detection.
There is no time limit. In this stage the firmware will wait indefinitely for the SMBus/I2C configuration.
When the SOC has completed configuring the device, it must write to register 0xFF to end the
configuration.
Configuration Stage (CONFIG)
Once the SOC has indicated that it is done with configuration, then all the configuration data is
combined. The default data, the SOC configuration data, the OTP data are all combined in the firmware
and device is programmed.
After the device is fully configured, it will go idle and then into suspend if there is no VBUS or
Hub.Connect present. Once VBUS is present, and upstream battery charging is enabled, the device
will transition to the Battery Charger Detection Stage (CHGDET). If VBUS is present, and upstream
battery charging is not enabled, the device will transitions to the Connect (Hub.Connect) stage.
2014 Microchip Technology Inc.
DS00001713A-page 25
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
5.1.6
Battery Charger Detection Stage (CHGDET)
After configuration, if enabled, the device enters the Battery Charger Detection Stage. If the battery
charger detection feature was disabled during the CONFIG stage, the device will immediately
transition to the Hub Connect (Hub.Connect) stage. If the battery charger detection feature remains
enabled, the battery charger detection sequence is started automatically.
If the charger detection remains enabled, the device will transition to the Hub.Connect stage if using
the hardware detection mechanism.
5.1.7
5.1.8
Hub Connect Stage (Hub.Connect)
Once the CHGDET stage is completed, the device enters the Hub.Connect stage.
Normal Mode
Lastly the SOC enters the Normal Mode of operation. In this stage, full USB operation is supported
under control of the USB Host on the upstream port. The device will remain in the normal mode until
the operating mode is changed by the system.
If RESET_N is asserted low, then Standby Mode is entered. The device may then be placed into any
of the designated Hub stages. Asserting the soft disconnect on the upstream port will cause the Hub
to return to the Hub.Connect stage until the soft disconnect is negated.
To save power, communication over the SMBus is not supported while in USB Suspend. The system
can prevent the device from going to sleep by asserting the ClkSusp control bit of the Configure
Portable Hub Register anytime before entering USB Suspend. While the device is kept awake during
USB Suspend, it will provide the SMBus functionality at the expense of not meeting USB requirements
for average suspend current consumption.
DS00001713A-page 26
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Chapter 6 Device Configuration
The device supports a large number of features (some mutually exclusive), and must be configured in
order to correctly function when attached to a USB host controller. The hub can be configured either
internally or externally depending on the implemented interface.
Microchip provides a comprehensive software programming tool, Pro-Touch, for configuring the
USB2534 functions, registers and OTP memory. All configuration is to be performed via the Pro-Touch
programming tool. For additional information on the Pro-Touch programming tool, contact your local
Microchip sales representative.
6.1
Configuration Method Selection
The CFG_SEL[1:0] configuration straps and the SDA pin are used to determine the hub configuration
method, as shown in Table 6.1. The software reads the SDA pin and the CFG_SEL[1:0] bits and
configures the system appropriately.
Table 6.1 Hub Configuration Selection
SDA
CFG_SEL1
CFG_SEL0
DESCRIPTION
X
0
0
Configuration is based on the configuration strap options and
internal OTP settings. This configuration sets the device Self
powered operation.
0
0
1
1
0
Invalid
X
Configuration based on the configuration strap options and
internal OTP settings. This configuration sets the device for Bus
powered operation.
1
1
1
0
1
1
Firmware performs a configuration load from 2-wire (I2C)
EEPROM. The device does not perform an SMBus Master
detection. Configuration is controlled by EEPROM values and
OTP settings. Strap options are disabled.
Firmware must wait for configuration from an SMBus Master.
Configuration is controlled by SMBus Master and OTP settings.
Strap options are disabled.
Note: Refer to Chapter 7, "Device Interfaces," on page 32 for detailed information on each device
configuration interface.
6.2
Customer Accessible Functions
The following USB or SMBus accessible functions are available to the customer via the Pro-Touch
Programming Tool.
Note: For additional programming details, refer to the Pro-Touch Programming Tool User Manual.
2014 Microchip Technology Inc.
DS00001713A-page 27
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
6.2.1
USB Accessible Functions
6.2.1.1
VSM commands over USB
By default, Vendor Specific Messaging (VSM) commands to the hub are enabled. The supported
commands are:
Enable Embedded Controller
Disable Embedded Controller
Enable Special Resume
Disable Special Resume
Reset Hub
2
6.2.1.2
6.2.1.3
6.2.1.4
I C Master Access over USB
Access to I2C devices is performed as a pass-through operation from the USB Host. The device
firmware has no knowledge of the operation of the attached I2C device. The supported commands are:
Enable I2C pass through mode
Disable I2C pass through mode
I2C write
I2C read
Send I2C start
Send I2C stop
OTP Access over USB
The OTP ROM in the device is accessible via the USB bus. All OTP parameters can modified via the
USB Host. The OTP operates in Single Ended mode. The supported commands are:
Enable OTP reset
Set OTP operating mode
Set OTP read mode
Program OTP
Get OTP status
Program OTP control parameters
Battery Charging Access over USB
The Battery charging behavior of the device can be dynamically changed by the USB Host when
something other than the preprogrammed or OTP programmed behavior is desired. The supported
commands are:
Enable/Disable battery charging
Upstream battery charging mode control
Downstream battery charging mode control
Battery charging timing parameters
Download custom battery charging algorithm
DS00001713A-page 28
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
6.2.1.5
Other Embedded Controller functions over USB
The following miscellaneous functions may be configured via USB:
Enable/Disable Embedded controller enumeration
Program Configuration parameters.
Program descriptor fields:
—Language ID
—Manufacturer string
—Product string
—idVendor
—idProduct
—bcdDevice
6.2.2
SMBus Accessible Functions
6.2.2.1
OTP Access over SMBus
The device’s OTP ROM is accessible over SMBus. All OTP parameters can modified via the SMbus
Host. The OTP can be programmed to operate in Single-Ended, Differential, Redundant, or Differential
Redundant mode, depending on the level of reliability required. The supported commands are:
Enable OTP reset
Set OTP operating mode
Set OTP read mode
Program OTP
Get OTP Status
Program OTP control parameters
6.2.2.2
Configuration Access over SMBus
The following functions are available over SMBus prior to the hub attaching to the USB host:
Program Configuration parameters.
Program descriptor fields:
—Language ID
—Manufacturer string
—Product string
—idVendor
—idProduct
—bcdDevice
Program Control Register
6.3
Device Configuration Straps
Configuration straps are multi-function pins that are driven as outputs during normal operation. During
a Power-On Reset (POR) or an External Chip Reset (RESET_N), these outputs are tri-stated. The high
or low state of the signal is latched following de-assertion of the reset and is used to determine the
default configuration of a particular feature. Configuration straps are latched as a result of a Power-On
Reset (POR) or a External Chip Reset (RESET_N). Configuration strap signals are noted in Chapter 3,
2014 Microchip Technology Inc.
DS00001713A-page 29
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
"Pin Descriptions," on page 10 and are identified by an underlined symbol name. The following sub-
sections detail the various configuration straps.
Configuration straps include internal resistors in order to prevent the signal from floating when
unconnected. If a particular configuration strap is connected to a load, an external pull-up or pull-down
should be used to augment the internal resistor to ensure that it reaches the required voltage level
prior to latching. The internal resistor can also be overridden by the addition of an external resistor.
Note: The system designer must guarantee that configuration straps meet the timing requirements
specified in Section 9.5.2, "Reset and Configuration Strap Timing," on page 46 and Section
9.5.1, "Power-On Configuration Strap Valid Timing," on page 45. If configuration straps are not
at the correct voltage level prior to being latched, the device may capture incorrect strap
values.
Note: Configuration straps must never be driven as inputs. If required, configuration straps can be
augmented, or overridden with external resistors.
6.3.1
Non-Removable Device (NON_REM[1:0])
The NON_REM[1:0] configuration straps are sampled at RESET_N negation to determine if ports [3:1]
contain permanently attached (non-removable) devices as follows. Additionally, because the
SUSP_IND indicator functionality is shared with the NON_REM0 configuration strap, the active state
of the LED connected to SUSP_IND will be determined as follows:
Table 6.2 NON_REM[1:0] Configuration Definitions
NON_REM[1:0]
DEFINITION
‘00’
‘01’
‘10’
‘11’
All USB ports removable, SUSP_IND LED active high
Port 1 is non-removable, SUSP_IND LED active low
Ports 1 & 2 are non-removable, SUSP_IND LED active high
Ports 1, 2 & 3 are non-removable, SUSP_IND LED active low
Note: If using the local power detect function (LOCAL_PWR pin), the NON_REM[1:0] configuration
straps cannot be used to configure the non-removable state of the USB ports. In this case, the
non-removable state of the ports must be configured in internal device registers via the
Protouch tool or SMBus.
6.3.2
6.3.3
Configuration Select (CFG_SEL[1:0])
Refer to Section 6.1, "Configuration Method Selection," on page 27 for details on CFG_SEL[1:0].
Downstream Battery Charging Enable (BC_EN[4:1])
The battery charging enable configuration straps are used to enable battery charging on the
corresponding downstream port. For example, if BC_EN1 is driven high during the configuration strap
latching time, downstream port 1 will indicate support of battery charging. Refer to Section 8.1.2,
"Downstream Battery Charging," on page 35 for additional information on battery charging.
DS00001713A-page 30
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
6.3.4
Port Disable (PRT_DIS_Mx/PRT_DIS_Px)
These configuration straps disable the associated USB ports D- and D+ signals, respectively, where
“x” is the USB port number. Both the negative “M” and positive “P” port disable configuration straps for
a given USB port must be tied high at reset to disable the associated port.
Table 6.3 PRT_DIS_Mx/PRT_DIS_Px Configuration Definitions
PRT_DIS_MX/PRT_DIS_PX
DEFINITION
‘0’
‘1’
Port x D-/D+ Signal is Enabled (Default)
Port x D-/D+ Signal is Disabled
2014 Microchip Technology Inc.
DS00001713A-page 31
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Chapter 7 Device Interfaces
The USB2534 provides multiple interfaces for configuration and external memory access. This chapter
details the various device interfaces and their usage.
Note: For information on device configuration, refer to Chapter 6, "Device Configuration," on page 27.
7.1
I2C Master Interface
The I2C master interface implements a subset of the I2C Master Specification (Please refer to the
Philips Semiconductor Standard I2C-Bus Specification for details on I2C bus protocols). The device’s
I2C master interface is designed to attach to a single “dedicated” I2C EEPROM for loading
configuration data and conforms to the Standard-Mode I2C Specification (100 kbit/s transfer rate and
7-bit addressing) for protocol and electrical compatibility. The device acts as the master and generates
the serial clock SCL, controls the bus access (determines which device acts as the transmitter and
which device acts as the receiver), and generates the START and STOP conditions.
Note: Extensions to the I2C Specification are not supported.
Note: All device configuration must be performed via the Pro-Touch Programming Tool. For additional
information on the Pro-Touch programming tool, contact your local sales representative.
2
7.1.1
I C Message Format
7.1.1.1
Sequential Access Writes
The I2C interface supports sequential writing of the device’s register address space. This mode is
useful for configuring contiguous blocks of registers. Figure 7.1 shows the format of the sequential
write operation. Where color is visible in the figure, blue indicates signaling from the I2C master, and
gray indicates signaling from the slave.
S
7-Bit Slave Address
0
A
xxxxxxxx
A
nnnnnnnn
A
...
nnnnnnnn
A
P
Register
Address
(bits 7-0)
Data value for
XXXXXX
Data value for
XXXXXX + y
Figure 7.1 I2C Sequential Access Write Format
In this operation, following the 7-bit slave address, the 8-bit register address is written indicating the
start address for sequential write operation. Every subsequent access is a data write to a data register,
where the register address increments after each access and an ACK from the slave occurs.
Sequential write access is terminated by a Stop condition.
7.1.1.2
Sequential Access Reads
The I2C interface supports direct reading of the device registers. In order to read one or more register
addresses, the starting address must be set by using a write sequence followed by a read. The read
register interface supports auto-increment mode. The master must send a NACK instead of an ACK
when the last byte has been transferred.
DS00001713A-page 32
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
In this operation, following the 7-bit slave address, the 8-bit register address is written indicating the
start address for the subsequent sequential read operation. In the read sequence, every data access
is a data read from a data register where the register address increments after each access. The write
sequence can end with optional Stop (P). If so, the read sequence must begin with a Start (S).
Otherwise, the read sequence must start with a Repeated Start (Sr).
Figure 7.2 shows the format of the read operation. Where color is visible in the figure, blue and gold
indicate signaling from the I2C master, and gray indicates signaling from the slave.
Optional. If present, Next
access must have Start(S),
otherwise Repeat Start (Sr)
S
7-Bit Slave Address
0
A
xxxxxxxx
A
P
Register
Address
(bits 7-0)
If previous write setting up
Register address ended with a
Stop (P), otherwise it will be
Repeated Start (Sr)
S
7-Bit Slave Address
1
ACK n n n n n n n n ACK n n n n n n n n ACK
...
n n n n n n n n NACK
P
Register value
for xxxxxxxx
Register value
for xxxxxxxx + 1
Register value
for xxxxxxxx + y
Figure 7.2 I2C Sequential Access Read Format
2
7.1.2
Pull-Up Resistors for I C
The circuit board designer is required to place external pull-up resistors (10 kΩ recommended) on the
SDA & SCL signals (per SMBus 1.0 Specification) to Vcc in order to assure proper operation.
7.2
SMBus Slave Interface
The USB2534 includes an integrated SMBus slave interface, which can be used to access internal
device run time registers or program the internal OTP memory. SMBus detection is accomplished by
detection of pull-up resistors (10 KΩ recommended) on both the SMBDATA and SMBCLK signals. To
disable the SMBus, a pull-down resistor of 10 KΩ must be applied to SMBDATA. The SMBus interface
can be used to configure the device as detailed in Section 6.1, "Configuration Method Selection," on
page 27.
Note: All device configuration must be performed via the Pro-Touch Programming Tool. For additional
information on the Pro-Touch programming tool, contact your local Microchip sales
representative.
2014 Microchip Technology Inc.
DS00001713A-page 33
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Chapter 8 Functional Descriptions
This chapter provides additional functional descriptions of key device features.
8.1
Battery Charger Detection & Charging
The USB2534 supports both upstream battery charger detection and downstream battery charging.
The integrated battery charger detection circuitry supports the USB-IF Battery Charging (BC1.2)
detection method and most Apple devices. These circuits are used to detect the attachment and type
of a USB charger and provide an interrupt output to indicate charger information is available to be read
from the device’s status registers via the serial interface. The USB2534 provides the battery charging
handshake and supports the following USB-IF BC1.2 charging profiles:
DCP: Dedicated Charging Port (Power brick with no data)
CDP: Charging Downstream Port (1.5A with data)
SDP: Standard Downstream Port (0.5A with data)
Custom profiles loaded via SMBus or OTP
The following sub-sections detail the upstream battery charger detection and downstream battery
charging features.
8.1.1
Upstream Battery Charger Detection
Battery charger detection is available on the upstream facing port. The detection sequence is intended
to identify chargers which conform to the Chinese battery charger specification, chargers which
conform to the USB-IF Battery Charger Specification 1.2, and most Apple devices.
In order to detect the charger, the device applies and monitors voltages on the upstream DP and DM
pins. If a voltage within the specified range is detected, the device will be updated to reflect the proper
status.
The device includes the circuitry required to implement battery charging detection using the Battery
Charging Specification. When enabled, the device will automatically perform charger detection upon
entering the Hub.ChgDet stage in Hub Mode. The device includes a state machine to provide the
detection of the USB chargers listed in the table below.
Table 8.1 Chargers Compatible with Upstream Detection
USB ATTACH TYPE
DP/DM PROFILE
CHARGERTYPE
DCP (Dedicated Charging Port)
CDP (Charging Downstream Port)
Shorted < 200ohm
001
VDP reflected to VDM
010
(EnhancedChrgDet = 1)
SDP
15Kohm pull-down on DP and DM
011
(Standard Downstream Port)
USB Host or downstream hub port
Apple Low Current Charger
Apple High Current Charger
Apple Super High Current Charger
Apple
Apple
100
101
110
DP=2.7V
DM=2.0V
DS00001713A-page 34
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Table 8.1 Chargers Compatible with Upstream Detection (continued)
USB ATTACH TYPE
DP/DM PROFILE
CHARGERTYPE
Apple Charger Low Current Charger (500mA)
DP=2.0V
DM=2.0V
100
Apple Charger High Current Charger (1000mA)
DP=2.0V
DM=2.7V
101
If a custom charger detection algorithm is desired, the SMBus registers can also be used to control
the charger detection block to implement a custom charger detection algorithm. In order to avoid
negative interactions with automatic battery charger detection or normal hub operation, the user should
only attempt Custom battery charger detection during the Hub.Config stage or Hub.Connect stage. No
logic is implemented to disable custom detection at other times - it is up to the user software to observe
this restriction.
There is a possibility that the system is not running the reference clock when battery charger detection
is required (for example if the battery is dead or missing). During the Hub.WaitRefClk stage the battery
charger detection sequence can be configured to be followed regardless of the activity of REFCLK by
relying on the operation of the internal oscillator.
8.1.2
Downstream Battery Charging
The device can be configured by an OEM to have any of the downstream ports to support battery
charging. The Hub's role in battery charging is to provide an acknowledge to a device's query as to if
the hub system supports USB battery charging. The hub silicon does not provide any current or power
FETs or any additional circuitry to actually charge the device. Those components must be provided as
externally by the OEM.
DC Power
Microchip
Hub
PRTPWR[n]
VBUS[n]
Figure 8.1 Battery Charging External Power Supply
If the OEM provides an external supply capable of supplying current per the battery charging
specification, the hub can be configured to indicate the presence of such a supply to the device. This
indication, via the PRTPWR[1:4] output pins, is on a per/port basis. For example, the OEM can
configure two ports to support battery charging through high current power FET's and leave the other
two ports as standard USB ports.
8.1.2.1
Downstream Battery Charging Modes
In the terminology of the USB Battery Charging Specification, if a port is configured to support battery
charging, the downstream port is a considered a CDP (Charging Downstream Port) if connected to a
2014 Microchip Technology Inc.
DS00001713A-page 35
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
USB host, or a DCP (Dedicated Charging Port) if not connected to a USB host. If the port is not
configured to support battery charging, the port is considered an SDP (Standard Downstream Port).
All charging ports have electrical characteristics different from standard non-charging ports.
A downstream port will behave as a CDP, DCP, or SDP depending on the port’s configuration and
mode of operation. The port will not switch between a CDP/DCP or SDP at any time after initial power-
up and configuration. A downstream port can be in one of three modes shown in the table below.
Table 8.2 Downstream Port Types
USB ATTACH TYPE
DP/DM PROFILE
DCP
Apple charging mode or
China Mode (Shorted < 200ohm) or
MCHP custom mode
(Dedicated Charging Port)
CDP
VDP reflected to VDM
(Charging Downstream Port)
SDP
15Kohm pull-down on DP and DM
(Standard Downstream Port)
USB Host or downstream hub port
8.1.2.2
8.1.2.3
Downstream Battery Charging Configuration
Configuration of ports to support battery charging is performed via the BC_EN configuration straps,
USB configuration, SMBus configuration, or OTP. The Battery Charging Enable Register provides per
port battery charging configuration. Starting from bit 1, this register enables battery charging for each
down stream port when asserted. Bit 1 represents port 1 and so on. Each port with battery charging
enabled asserts the corresponding PRTPWR register bit.
Downstream Over-Current Management
It is the devices responsibility to manage over-current conditions. Over-Current Sense (OCS) is
handled according to the USB specification. For battery charging ports, PRTPWR is driven high
(asserted) after hardware initialization. If an OCS event occurs, the PRTPWR is negated. PRTPWR
will be negated for all ports in a ganged configuration. Only the respective PRTPWR will be negated
in the individual configuration.
If there is an over-current event in DCP mode, the port is turned off for one second and is then re-
enabled. If the OCS event persists, the cycle is repeated for a total or three times. If after three
attempts, the OCS still persists, the cycle is still repeated, but with a retry interval of ten seconds. This
retry persists for indefinitely. The indefinite retry prevents a defective device from permanently disabling
the port.
In CDP or SDP mode, the port power and over-current events are controlled by the USB host. The
OCS event does not have to be registered. When and if the hub is connected to a host, the host will
initialize the hub and enable its port power. If the over current still exists, it will be notified at that point.
DS00001713A-page 36
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
8.2
Flex Connect
This feature allows the upstream port to be swapped with downstream physical port 1. Only
downstream port 1 can be swapped physically. Using port remapping, any logical port (number
assignment) can be swapped with the upstream port (non-physical).
Flex Connect is enabled/disabled via two control bits in the Connect Configuration Register. The
FLEXCONNECT configuration bit switches the port, and EN_FLEX_MODE enables the mode.
8.2.1
Port Control
Once EN_FLEX_MODE bit is set, the functions of certain pins change, as outlined below.
If EN_FLEX_MODE is set and FLEXCONNECT is not set:
1. PRTPWR1 enters combined mode, becoming PRTPWR1/OCS1_N
2. OCS1_N becomes a don’t care
3. SUSPEND outputs ‘0’ to keep any upstream power controller off
If EN_FLEX_MODE is set and FLEXCONNECT is set:
1. The normal upstream VBUS pin becomes a don’t care
2. PRTPWR1 is forced to a ‘1’ in combined mode, keeping the port power on to the application
processor.
3. OCS1 becomes VBUS from the application processor through a GPIO
4. SUSPEND becomes PRTPWR1/OCS1_N for the port power controller for the connector port
8.3
Resets
The device has the following chip level reset sources:
Power-On Reset (POR)
External Chip Reset (RESET_N)
USB Bus Reset
8.3.1
8.3.2
Power-On Reset (POR)
A power-on reset occurs whenever power is initially supplied to the device, or if power is removed and
reapplied to the device. A timer within the device will assert the internal reset per the specifications
listed in Section 9.5.1, "Power-On Configuration Strap Valid Timing," on page 45.
External Chip Reset (RESET_N)
A valid hardware reset is defined as assertion of RESET_N, after all power supplies are within
operating range, per the specifications in Section 9.5.2, "Reset and Configuration Strap Timing," on
page 46. While reset is asserted, the device (and its associated external circuitry) enters Standby Mode
and consumes minimal current.
Assertion of RESET_N causes the following:
1. The PHY is disabled and the differential pairs will be in a high-impedance state.
2. All transactions immediately terminate; no states are saved.
3. All internal registers return to the default state.
2014 Microchip Technology Inc.
DS00001713A-page 37
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
4. The external crystal oscillator is halted.
5. The PLL is halted.
Note: All power supplies must have reached the operating levels mandated in Section 9.2, "Operating
Conditions**," on page 42, prior to (or coincident with) the assertion of RESET_N.
8.3.3
USB Bus Reset
In response to the upstream port signaling a reset to the device, the device performs the following:
Note: The device does not propagate the upstream USB reset to downstream devices.
1. Sets default address to 0.
2. Sets configuration to: Unconfigured.
3. Moves device from suspended to active (if suspended).
4. Complies with Section 11.10 of the USB 2.0 Specification for behavior after completion of the
reset sequence.
The host then configures the device in accordance with the USB Specification.
8.4
Link Power Management (LPM)
The device supports the L0 (On), L1 (Sleep), and L2 (Suspend) link power management states per
the USB 2.0 Link Power Management Addendum. These supported LPM states offer low transitional
latencies in the tens of microseconds versus the much longer latencies of the traditional USB
suspend/resume in the tens of milliseconds. The supported LPM states are detailed in Table 8.3. For
additional information, refer to the USB 2.0 Link Power Management Addendum.
Table 8.3 LPM State Definitions
STATE
DESCRIPTION
ENTRY/EXIT TIME TO L0
Entry: ~3 ms
L2
L1
L0
Suspend
Sleep
Exit: ~2 ms
Entry: ~65 us
Exit: ~100 us
Fully Enabled (On)
-
Note: State change timing is approximate and is measured by change in power consumption.
Note: System clocks are stopped only in suspend mode or when power is removed from the device.
8.5
Remote Wakeup Indicator (SUSP_IND)
The remote wakeup indicator feature uses the SUSP_IND as a side band signal to wake up the host
when in suspend. This feature is enabled and disabled via the HUB_RESUME_INHIBIT configuration
bit in the hub configuration space register CFG3. The only way to control the bit is by configuration
EEPROM, SMBus or internal ROM default setting. The state is only modified during a power on reset,
or hardware reset. No dynamic reconfiguring of this capability is possible.
DS00001713A-page 38
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
When HUB_RESUME_INHIBIT = ‘0’, Normal Resume Behavior per the USB 2.0 specification
When HUB_RESUME_INHIBIT = ‘1’, Modified Resume Behavior is enabled
Refer to the following subsections for additional details.
8.5.1
Normal Resume Behavior
VBUS_DET is used to detect presence of the Host. If VBUS_DET = ‘1’, then D+ pull-up is asserted
and normal USB functionality is enabled. The SUSP_IND provides an indication of the active or
suspended state of the hub.
The Hub will drive a ‘K’ on the upstream port if required to do so by USB protocol.
If VBUS_DET = ‘0’, then the D+ pull-up is negated. If battery charging is not enabled, the internal hub
logic will be reset, thus negating all downstream ports and associated downstream VBUS enable
signals. The hub will need to be re-enumerated to function, much like a new connect or after a
complete system reset.
8.5.2
Modified Resume Behavior
When the modified resume feature is enabled, the hub functions as follows:
VBUS_DET is used to detect presence of the Host. If VBUS_DET = ‘1’, then D+ pull-up is asserted
and normal USB functionality is enabled. SUSP_IND provides an indication of the active or suspended
state of the hub.
The device will drive a ‘K’ on the upstream port and downstream ports if required to do so by USB
protocol. The device will act as a controlling hub if required to do so by the USB protocol.
If VBUS_DET = ‘0’, then the D+ pull-up is negated, but the hub will not be internally reset. It will power-
on the downstream ports. The hub is able to continue to detect downstream remote wake events.
SUSP_IND provides an indication of the active or suspended state of the hub.
If a USB 2.0 specification compliant resume or wake event is detected by the device, the device is
remote wake enabled, and a port status change event occurs, SUSP_IND will be driven for the time
given in the GLOBAL_RESUME_TIME register.
If a remote wake event is detected on a downstream port:
1. Device disconnect
2. Device connect
3. A currently connected device requests remote wake-up.
Note: Downstream resume events are filtered for approximately 100uS by internal logic.
The device will not drive a ‘K’ on the upstream port. Instead, the SUSP_IND will be driven for
approximately 14 ms. The ‘K’ is not driven upstream because this would potentially back drive a
powered-down host. The device will drive RESUME to only the downstream ports which transmitted
the remote wake signal per the requirements of the USB 2.0 specification for controlling hub behavior.
Note: SUSP_IND is a one shot event. It will assert with each wake event detection. It will not
repeatedly assert in proxy for downstream devices.
For the case where the Host responds and turns on VBUS and can drive a ‘K’ downstream within the
14 ms time frame of a standard resume (measured from the SUSP_IND pin), then the hub detects the
‘K’. It will discontinue “Controlling Hub” activities, drive resume signaling on any other ports, and
2014 Microchip Technology Inc.
DS00001713A-page 39
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
function as expected per the USB 2.0 Specification with respect to a resume event. It will permit the
host to take over resume signaling.
For the case where the host is not able to drive a ‘K’ within the 14 ms time frame, the hub will stop
sending a ‘K’ on the upstream and downstream ports. It must follow through as a controlling hub and
properly terminate the resume with either an EOP or with HS terminations as is currently implemented
in the selective resume case, per the USB specification.
8.6
High Speed Indicator (HS_IND)
The HS_IND pin can be used to drive an LED. The active state of the LED will be determined as
follows:
If CFG_SEL1 = ‘0’, HS_IND is active high.
If CFG_SEL1 = ‘1’, then HS_IND is active low.
Assertion of HS_IND indicates the device is connected at high speed. Negation of HS_IND indicates
the device is connected at full speed.
Note: This pin shares functionality with the CFG_SEL1 configuration strap. The logic state of this pin
is internally latched on the rising edge of RESET_N (RESET_N negation), and is used to
determine the hub configuration method. Refer to Section 6.3.2, "Configuration Select
(CFG_SEL[1:0])," on page 30 for additional information.
DS00001713A-page 40
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Chapter 9 Operational Characteristics
9.1
Absolute Maximum Ratings*
+3.3 V Supply Voltage (VDD33, VDDA33) (Note 9.1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to +3.6 V
Positive voltage on input signal pins, with respect to ground (Note 9.2) . . . . . . . . . . . . . . . . . . . . 3.6 V
Negative voltage on input signal pins, with respect to ground . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V
Positive voltage on XTAL1/REFCLK, with respect to ground . . . . . . . . . . . . . . . . . . . . . . . . .VDDCR12
Positive voltage on USB DP/DM signals, with respect to ground (Note 9.3) . . . . . . . . . . . . . . . . . 5.5 V
Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-55oC to +150oC
Lead Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to JEDEC Spec. J-STD-020
HBM ESD Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..JEDEC Class 3A
Note 9.1 When powering this device from laboratory or system power supplies, it is important that
the absolute maximum ratings not be exceeded or device failure can result. Some power
supplies exhibit voltage spikes on their outputs when AC power is switched on or off. In
addition, voltage transients on the AC power line may appear on the DC output. If this
possibility exists, it is suggested to use a clamp circuit.
Note 9.2 This rating does not apply to the following signals: All USB DM/DP pins, XTAL1/REFCLK,
XTAL2.
Note 9.3 This rating applies only when VDD33 is powered.
*Stresses exceeding those listed in this section could cause permanent damage to the device. This is
a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability. Functional operation of the device at any condition exceeding those indicated in
Section 9.2, "Operating Conditions**", Section 9.4, "DC Specifications", or any other applicable section
of this specification is not implied. Note, device signals are NOT 5 volt tolerant unless specified
otherwise.
2014 Microchip Technology Inc.
DS00001713A-page 41
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
9.2
Operating Conditions**
+3.3 V Supply Voltage (VDD33, VDDA33) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +3.0 V to 3.6 V
Power Supply Rise Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note 9.4
Ambient Operating Temperature in Still Air (TA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note 9.5
Note 9.4 The power supply rise time requirements vary dependent on the usage of the external
reset (RESET_N). If RESET_N is asserted at power-on, the power supply rise time must
be 10mS or less (tRT(max) = 10mS). If RESET_N is not used at power-on (tied high), the
power supply rise time must be 1mS or less (tRT(max) = 1mS). Figure 9.1 illustrates the
supply rise time requirements.
Note 9.5 0oC to +70oC for commercial version, -40oC to +85oC for industrial version.
**Proper operation of the device is guaranteed only within the ranges specified in this section.
Voltage
tRT
3.3V
100%
VDDA33
90%
10%
VSS
t90%
Time
t10%
Figure 9.1 Supply Rise Time Model
DS00001713A-page 42
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
9.3
Power Consumption
This section details the power consumption of the device as measured during various modes of
operation. Power dissipation is determined by temperature, supply voltage, and external source/sink
requirements.
9.3.1
Operational / Unconfigured
Table 9.1 Operational/Unconfigured Power Consumption
TYPICAL (mA)
VDD33
MAXIMUM (mA)
VDD33
HS Host / 1 HS Device
HS Host / 2 HS Devices
HS Host / 3 HS Devices
HS Host / 4 HS Devices
HS Host / 1 FS Device
HS Host / 2 FS Devices
HS Host / 3 FS Devices
HS Host / 4 FS Devices
Unconfigured
65
95
75
110
145
175
50
125
155
45
50
60
55
70
65
80
30
-
9.3.2
Suspend / Standby
Table 9.2 Suspend/Standby Power Consumption
MODE
SYMBOL
TYPICAL @ 25oC
COMMERCIAL
MAX
INDUSTRIAL
UNIT
MAX
Suspend
Standby
IVDD33
IVDD33
320
75
1250
130
1750
140
uA
uA
Note: Typical values measured with VDD33 = 3.3V. Maximum values measured with VDD33 = 3.6V.
2014 Microchip Technology Inc.
DS00001713A-page 43
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
9.4
DC Specifications
Table 9.3 DC Electrical Characteristics
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
NOTES
IS Type Input Buffer
Low Input Level
VIL
VIH
-0.3
2.0
0.8
3.6
V
V
High Input Level
I_RST Type Input Buffer
Low Input Level
VIL
VIH
-0.3
0.4
3.6
V
V
High Input Level
1.25
I_SMB Type Input Buffer
Low Input Level
VIL
VIH
-0.3
0.35
3.6
V
V
High Input Level
1.25
O8 Type Buffers
Low Output Level
High Output Level
OD8 Type Buffer
Low Output Level
OD12 Type Buffer
Low Output Level
VOL
VOH
0.4
V
V
IOL = 8 mA
IOH = -8 mA
VDD33 - 0.4
VOL
0.4
0.4
V
V
IOL = 8 mA
VOL
IOL = 12 mA
ICLK Type Buffer
(XTAL1/REFCLK Input)
Low Input Level
High Input Level
VIL
VIH
-0.3
0.8
0.35
3.6
V
V
DS00001713A-page 44
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
9.5
AC Specifications
This section details the various AC timing specifications of the device.
9.5.1
Power-On Configuration Strap Valid Timing
Figure 9.2 illustrates the configuration strap timing requirements, in relation to power-on, for
applications where RESET_N is not used at power-on. The operational level (Vopp) for the external
power supply is detailed in Section 9.2, "Operating Conditions**," on page 42.
Note: For RESET_N configuration strap timing requirements, refer to Section 9.5.2, "Reset and
Configuration Strap Timing," on page 46.
External Power
Supply
Vopp
tcsh
Configuration
Straps
Figure 9.2 Power-On Configuration Strap Valid Timing
Table 9.4 Power-On Configuration Strap Valid Timing
SYMBOL
DESCRIPTION
MIN
TYP
MAX
UNITS
tcsh
Configuration strap hold after external power supply at
operational level
1
ms
2014 Microchip Technology Inc.
DS00001713A-page 45
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
9.5.2
Reset and Configuration Strap Timing
Figure 9.3 illustrates the RESET_N timing requirements and its relation to the configuration strap
signals. Assertion of RESET_N is not a requirement. However, if used, it must be asserted for the
minimum period specified.
Refer to Section 8.3, "Resets," on page 37 for additional information on resets. Refer to Section 6.3,
"Device Configuration Straps," on page 29 for additional information on configuration straps.
trstia
RESET_N
tcsh
Configuration
Straps
Figure 9.3 RESET_N Configuration Strap Timing
Table 9.5 RESET_N Configuration Strap Timing
SYMBOL
DESCRIPTION
MIN
TYP
MAX
UNITS
trstia
tcsh
RESET_N input assertion time
5
1
us
Configuration strap hold after RESET_N deassertion
ms
9.5.3
USB Timing
All device USB signals conform to the voltage, power, and timing characteristics/specifications as set
forth in the Universal Serial Bus Specification. Please refer to the Universal Serial Bus Specification,
Revision 2.0, available at http://www.usb.org.
9.5.4
9.5.5
SMBus Timing
All device SMBus signals conform to the voltage, power, and timing characteristics/specifications as
set forth in the System Management Bus Specification. Please refer to the System Management Bus
Specification, Version 1.0, available at http://smbus.org/specs.
2
I C Timing
All device I2C signals conform to the 100KHz Standard Mode (Sm) voltage, power, and timing
characteristics/specifications as set forth in the I2C-Bus Specification. Please refer to the I2C-Bus
Specification, available at http://www.nxp.com.
DS00001713A-page 46
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
9.6
Clock Specifications
The device can accept either a 24 MHz crystal or a 24 MHz single-ended clock oscillator input. If the
single-ended clock oscillator method is implemented, XTAL1 should be left unconnected and REFCLK
should be driven with a clock that adheres to the specifications outlined in Section 9.6.2, "External
Reference Clock (REFCLK)".
9.6.1
Oscillator/Crystal
It is recommended that a crystal utilizing matching parallel load capacitors be used for the crystal
input/output signals (XTAL1I/XTAL2). See Table 9.6 for the recommended crystal specifications.
Table 9.6 Crystal Specifications
PARAMETER
SYMBOL
MIN
NOM
MAX
UNITS
NOTES
Crystal Cut
AT, typ
Fundamental Mode
Parallel Resonant Mode
Crystal Oscillation Mode
Crystal Calibration Mode
Frequency
Ffund
-
24.000
-
MHz
PPM
oC
Total Allowable PPM Budget
Operating Temperature Range
-
-
-
+/-350
Note 9.7
Note 9.6
Note 9.6 0oC for commercial version, -40oC for industrial version.
Note 9.7 +70oC for commercial version, +85oC for industrial version.
9.6.2
External Reference Clock (REFCLK)
The following input clock specifications are suggested:
24 MHz 350 PPM
Note: The external clock is recommended to conform to the signalling levels designated in the
JEDEC specification on 1.2V CMOS Logic. XTAL2 should be treated as a no connect when an
external clock is supplied.
2014 Microchip Technology Inc.
DS00001713A-page 47
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Chapter 10 Package Outline
Figure 10.1 36-SQFN Package Drawing
DS00001713A-page 48
2014 Microchip Technology Inc.
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
2014 Microchip Technology Inc.
DS00001713A-page 49
USB 2.0 Hi-Speed 4-Port Hub Controller
Datasheet
Chapter 11 Datasheet Revision History
Table 11.1 Revision History
REVISION LEVEL
& DATE
SECTION/FIGURE/ENTRY
CORRECTION
DS00001713A replaces the previous SMSC version, revision 1.1
Rev. 1.1
(12-06-13)
SMBus Runtime Registers
Register definitions removed. These definitions are
provided in application note AN 26.18 “SMBus
Slave Interface for the
USB253x/USB3x13/USB46x4”.
Rev. 1.1
(09-24-13)
Table 9.3, “DC Electrical
Updated ICLK VIH max from “VDDCR12” to “3.6”
Removed 50% duty cycle requirement.
Characteristics,” on page 44
Section 9.6.2, "External Reference
Clock (REFCLK)," on page 47
Table 6.1, “Hub Configuration
Selection,” on page 27
Corrected SDA and CFG_SEL1 values for last two
entries in the table.
Rev. 1.0
Initial Release
(06-17-13)
DS00001713A-page 50
2014 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device applications and the like is provided only for your convenience and may be
superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO
REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE,
MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of
Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implic-
itly or otherwise, under any Microchip intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32
logo, rfPIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and
other countries.
FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MTP, SEEVAL and The Embedded Control Solutions Company are
registered trademarks of Microchip Technology Incorporated in the U.S.A.
Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries.
Analog-for-the-Digital Age, Application Maestro, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net,
dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM,
MPF, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit,
PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O, Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA and Z-
Scale are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated in the U.S.A.
GestIC and ULPP are registered trademarks of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip
Technology Inc., in other countries.
flexPWR, JukeBlox, Kleer, KleerNet, MediaLB, and MOST
The preceding is a non-exhaustive list of trademarks in use in the US and other countries. For a complete list of trademarks, email a
request to legal.department@microchip.com. The absence of a trademark (name, logo, etc.) from the list does not constitute a waiver
of any intellectual property rights that SMSC has established in any of its trademarks.
All other trademarks mentioned herein are property of their respective companies.
© 2014, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved.
ISBN: 9781632760272
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
QUALITY MANAGEMENT SYSTEM
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
CERTIFIED BY DNV
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
== ISO/TS 16949 ==
2014 Microchip Technology Inc.
DS00001713A-page 51
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2943-5100
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
India - Pune
Tel: 91-20-3019-1500
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
Web Address:
www.microchip.com
Japan - Osaka
Tel: 81-6-6152-7160
Fax: 81-6-6152-9310
Germany - Dusseldorf
Tel: 49-2129-3766400
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Japan - Tokyo
Tel: 81-3-6880- 3770
Fax: 81-3-6880-3771
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Austin, TX
Tel: 512-257-3370
Germany - Pforzheim
Tel: 49-7231-424750
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
Boston
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Hangzhou
Tel: 86-571-8792-8115
Fax: 86-571-8792-8116
Italy - Venice
Tel: 39-049-7625286
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Hong Kong SAR
Tel: 852-2943-5100
Fax: 852-2401-3431
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Poland - Warsaw
Tel: 48-22-3325737
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Sweden - Stockholm
Tel: 46-8-5090-4654
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Detroit
Novi, MI
Tel: 248-848-4000
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
Houston, TX
Tel: 281-894-5983
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Taiwan - Kaohsiung
Tel: 886-7-213-7830
China - Shenzhen
Tel: 86-755-8864-2200
Fax: 86-755-8203-1760
Taiwan - Taipei
Tel: 886-2-2508-8600
Fax: 886-2-2508-0102
Los Angeles
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
Canada - Toronto
Tel: 905-673-0699
Fax: 905-673-6509
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
03/25/14
DS00001713A-page 52
2014 Microchip Technology Inc.
相关型号：
USB260-E3/2CT
Rectifier Diode, 1 Phase, 1 Element, 2A, 600V V(RRM), Silicon, DO-214AA, ROHS COMPLIANT, PLASTIC, SMB, 2 PIN
VISHAY
USB260-E3/55T
Rectifier Diode, 1 Phase, 1 Element, 2A, 600V V(RRM), Silicon, DO-214AA, ROHS COMPLIANT, PLASTIC, SMB, 2 PIN
VISHAY
USB260-HE3/52T
DIODE 2 A, 600 V, SILICON, RECTIFIER DIODE, DO-214AA, ROHS COMPLIANT, PLASTIC, SMB, 2 PIN, Rectifier Diode
VISHAY
©2020 ICPDF网 联系我们和版权申明