ATWINC3400-WING [MICROCHIP]
Wireless Network Controller;型号: | ATWINC3400-WING |
厂家: | MICROCHIP |
描述: | Wireless Network Controller 无线 |
文件: | 总2页 (文件大小:923K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SmartConnect WINC3400
Wireless Network Controller
The Atmel® SmartConnect ATWINC3400 is a single-chip IEEE 802.11 b/g/n RF/Baseband/MAC network controller and Bluetooth®
4.0 Low Energy (BLE) compliant module optimized for low-power mobile applications. It supports single stream 1x1 802.11n mode,
providing up to 72 Mbps throughput. The ATWINC3400 device features a fully integrated power amplifier, LNA, switch and power
management, as well as an on-chip microcontroller (MCU) and integrated Flash memory for system software. Implemented in 65nm
CMOS technology, it offers very low power consumption while simultaneously providing high performance and a minimal bill of materials.
The ATWINC3400 wireless network controller utilizes highly optimized coexistence protocols. It provides multiple peripheral interfaces,
including UART, SPI, I2C, and SDIO. For simplicity, both Wi-Fi and BLE can run on a single peripheral interface (SPI).
The only external clock sources required is a high-speed crystal or oscillator with a wide range of reference clock frequencies supported
(14-40 MHz) and a 32.768 kHz clock for sleep operation. The device is available in QFN packaging.
Key Features
IEEE 802.11
Bluetooth Low Energy
•
•
•
•
•
•
•
•
•
•
IEEE 802.11 b/g/n RF/PHY/MAC SoC
IEEE 802.11 b/g/n (1x1) for up to 72 Mbps
Single spatial stream in 2.4GHz ISM band
Integrated PA and T/R switch
Superior sensitivity & range via advanced PHY signal processing
Advanced equalization and channel estimation
Advanced carrier and timing synchronization
Wi-Fi Direct and Soft-AP support
Supports IEEE 802.11 WEP, WPA, WPA2 security
Superior MAC throughput via hardware accelerated
two-level A-MSDU/A-MPDU frame aggregation and block
acknowledgement
On-chip memory management engine to reduce host load
SPI, SDIO, I2C, and UART host interfaces
Operating temperature range of -30°C to +85°C
Fast boot options:
•
•
•
•
•
•
Bluetooth 4.0 low energy (BLE) technology
Class 1 & 2 transmission
Adaptive frequency hopping
HCI (Host Control Interface) via SPI (or UART)
Integrated PA and T/R switch
Superior sensitivity and range
Target Applications
•
•
•
•
•
•
•
IoT applications
Smart appliances
Healthcare
Home automation
Consumer electronics
Industrial automation
Mobile applications
•
•
•
•
- On-chip boot ROM (firmware instant boot)
- SPI flash boot (firmware patches and state variables)
- Low-leakage on-chip memory for state variables
- Fast AP re-association (150ms)
•
On-chip network stack to offload MCU:
- Integrated Nnetwork IP stack to minimize host
CPU requirements
- Network features: TCP, UDP, DHCP, ARP, HTTP, SSL,
and DNS
Power Architecture and Consumption
The ATWINC3400 has multiple device states, depending on the state of the 802.11 and Bluetooth subsystems. It is possible for both
subsystems to be active at the same time. To simplify the device power consumption breakdown, the following basic states—for which
only one subsystem can be active at a time—are defined as follows:
•
•
•
•
•
•
WiFi_ON_Transmit: Device is actively transmitting an 802.11 signal
WiFi_ON_Receive: Device is actively receiving an 802.11 signal
BT_ON_Transmit: Device is actively transmitting a Bluetooth signal
BT_ON_Receive: Device is actively receiving a Bluetooth signal
Doze: Device is neither transmitting nor receiving (device state is retained)
Power_Down: Device is powered down with CHIP_EN low and supplies connected
Accelerating RF Design
To help designers accelerate development, the ATWINC3400A-MU is offered as a single chip, module, or evaluation kit for fast integration.
Ordering Codes
Description
ATWINC3400A-MU
ATWINC3400-MR210CA
ATWINC3400-WING
Single-chip IEEE 802.11 b/g/n RF/Baseband/MAC network controller and BLE 4.0
Fully certified WINC3400 with chip antenna
Evaluation kit, fully certified WINC3400 with chip antenna
Evaluation kit, including Atmel® | SMART SAMD21 MPU and WINC3400
network controller
ATWINC3400-XSTK
Atmel Corporation
1600 Technology Drive, San Jose, CA 95110 USA
T : (+1)(408) 441. 0311
F : (+1)(408) 436. 4200
|
www.atmel.com
© 2015 Atmel Corporation. / Rev.: Atmel-45125A-WINC3400-Flyer_E_US_112015
Atmel,® Atmel logo and combinations thereof, Enabling Unlimited Possibilities,® and others are registered trademarks or trademarks of Atmel Corporation in U.S. and other
countries. Other terms and product names may be trademarks of others.
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel
products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RE-
LATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE
THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to
make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall
not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.
DS70005268A
相关型号:
©2020 ICPDF网 联系我们和版权申明