ATMEGA329V-8MUR [MICROCHIP]
IC MCU 8BIT 32KB FLASH 64QFN;型号: | ATMEGA329V-8MUR |
厂家: | MICROCHIP |
描述: | IC MCU 8BIT 32KB FLASH 64QFN 时钟 微控制器 外围集成电路 |
文件: | 总30页 (文件大小:838K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Features
• High Performance, Low Power Atmel®AVR® 8-Bit Microcontroller
• Advanced RISC Architecture
– 130 Powerful Instructions – Most Single Clock Cycle Execution
– 32 x 8 General Purpose Working Registers
– Fully Static Operation
– Up to 16 MIPS Throughput at 16MHz
– On-Chip 2-cycle Multiplier
• High Endurance Non-volatile Memory Segments
– In-System Self-programmable Flash Program Memory
• 32KBytes (ATmega329/ATmega3290)
• 64KBytes (ATmega649/ATmega6490)
– EEPROM
8-bit Atmel
• 1Kbytes (ATmega329/ATmega3290)
• 2Kbytes (ATmega649/ATmega6490)
– Internal SRAM
• 2Kbytes (ATmega329/ATmega3290)
• 4Kbytes (ATmega649/ATmega6490)
– Write/Erase Cycles: 10,000 Flash/ 100,000 EEPROM
– Data retention: 20 years at 85°C/100 years at 25°C(1)
– Optional Boot Code Section with Independent Lock Bits
• In-System Programming by On-chip Boot Program
• True Read-While-Write Operation
Microcontroller
with In-System
Programmable
Flash
– Programming Lock for Software Security
• JTAG (IEEE std. 1149.1 compliant) Interface
– Boundary-scan Capabilities According to the JTAG Standard
– Extensive On-chip Debug Support
– Programming of Flash, EEPROM, Fuses, and Lock Bits through the JTAG Interface
• Peripheral Features
ATmega329/V
ATmega3290/V
ATmega649/V
ATmega6490/V
– 4 x 25 Segment LCD Driver (ATmega329/ATmega649)
– 4 x 40 Segment LCD Driver (ATmega3290/ATmega6490)
– Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode
– One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture
Mode
– Real Time Counter with Separate Oscillator
– Four PWM Channels
– 8-channel, 10-bit ADC
– Programmable Serial USART
– Master/Slave SPI Serial Interface
Summary
– Universal Serial Interface with Start Condition Detector
– Programmable Watchdog Timer with Separate On-chip Oscillator
– On-chip Analog Comparator
– Interrupt and Wake-up on Pin Change
• Special Microcontroller Features
– Power-on Reset and Programmable Brown-out Detection
– Internal Calibrated Oscillator
– External and Internal Interrupt Sources
– Five Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, and
Standby
• I/O and Packages
– 53/68 Programmable I/O Lines
– 64-lead TQFP, 64-pad QFN/MLF, and 100-lead TQFP
• Speed Grade:
– ATmega329V/ATmega3290V/ATmega649V/ATmega6490V:
– 0 - 4MHz @ 1.8 - 5.5V, 0 - 8MHz @ 2.7 - 5.5V
– ATmega329/3290/649/6490:
– 0 - 8MHz @ 2.7 - 5.5V, 0 - 16MHz @ 4.5 - 5.5V
• Temperature range:
– -40°C to 85°C Industrial
• Ultra-Low Power Consumption
– Active Mode:
• 1MHz, 1.8V: 350µA
• 32kHz, 1.8V: 20µA (including Oscillator)
• 32kHz, 1.8V: 40µA (including Oscillator and LCD)
– Power-down Mode:
• 100nA at 1.8V
2552KS–AVR–04/11
ATmega329/3290/649/6490
1. Pin Configurations
Figure 1-1. Pinout ATmega3290/6490
TQFP
1
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
LCDCAP
PA3 (COM3)
PA4 (SEG0)
PA5 (SEG1)
PA6 (SEG2)
PA7 (SEG3)
PG2 (SEG4)
PC7 (SEG5)
PC6 (SEG6)
DNC
2
(RXD/PCINT0) PE0
INDEX CORNER
3
(TXD/PCINT1) PE1
(XCK/AIN0/PCINT2) PE2
(AIN1/PCINT3) PE3
(USCK/SCL/PCINT4) PE4
(DI/SDA/PCINT5) PE5
(DO/PCINT6) PE6
(CLKO/PCINT7) PE7
VCC
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
PH3 (PCINT19/SEG7)
PH2 (PCINT18/SEG8)
PH1 (PCINT17/SEG9)
PH0 (PCINT16/SEG10)
DNC
GND
DNC
(PCINT24/SEG35) PJ0
(PCINT25/SEG34) PJ1
DNC
ATmega3290/6490
DNC
DNC
DNC
DNC
DNC
DNC
PC5 (SEG11)
PC4 (SEG12)
PC3 (SEG13)
PC2 (SEG14)
PC1 (SEG15)
PC0 (SEG16)
PG1 (SEG17)
PG0 (SEG18)
(SS/PCINT8) PB0
(SCK/PCINT9) PB1
(MOSI/PCINT10) PB2
(MISO/PCINT11) PB3
(OC0A/PCINT12) PB4
(OC1A/PCINT13) PB5
(OC1B/PCINT14) PB6
2
2552KS–AVR–04/11
ATmega329/3290/649/6490
Figure 1-2. Pinout ATmega329/649
LCDCAP
(RXD/PCINT0) PE0
(TXD/PCINT1) PE1
1
2
3
PA3 (COM3)
PA4 (SEG0)
PA5 (SEG1)
PA6 (SEG2)
48
47
46
INDEX CORNER
(XCK/AIN0/PCINT2) PE2
4
45
(AIN1/PCINT3) PE3
5
6
PA7 (SEG3)
PG2 (SEG4)
PC7 (SEG5)
PC6 (SEG6)
PC5 (SEG7)
PC4 (SEG8)
PC3 (SEG9)
PC2 (SEG10)
PC1 (SEG11)
PC0 (SEG12)
44
43
(USCK/SCL/PCINT4) PE4
(DI/SDA/PCINT5) PE5
(DO/PCINT6) PE6
7
8
9
42
41
40
ATmega329/649
(CLKO/PCINT7) PE7
(SS/PCINT8) PB0 10
(SCK/PCINT9) PB1 11
(MOSI/PCINT10) PB2 12
(MISO/PCINT11) PB3 13
39
38
37
36
(OC0A/PCINT12) PB4 14
(OC1A/PCINT13) PB5 15
(OC1B/PCINT14) PB6 16
35
34
33
PG1 (SEG13)
PG0 (SEG14)
Note:
The large center pad underneath the QFN/MLF packages is made of metal and internally con-
nected to GND. It should be soldered or glued to the board to ensure good mechanical stability. If
the center pad is left unconnected, the package might loosen from the board.
3
2552KS–AVR–04/11
ATmega329/3290/649/6490
2. Overview
The ATmega329/3290/649/6490 is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architec-
ture. By executing powerful instructions in a single clock cycle, the ATmega329/3290/649/6490 achieves throughputs
approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed.
2.1
Block Diagram
Figure 2-1. Block Diagram
PF0 - PF7
PA0 - PA7
PC0 - PC7
GND
VCC
PORTA DRIVERS
PORTF DRIVERS
PORTC DRIVERS
DATA REGISTER
PORTF
DATA DIR.
REG. PORTF
DATA REGISTER
PORTA
DATA DIR.
REG. PORTA
DATA REGISTER
PORTC
DATA DIR.
REG. PORTC
8-BIT DATA BUS
AVCC
CALIB. OSC
AGND
AREF
ADC
INTERNAL
OSCILLATOR
OSCILLATOR
PROGRAM
COUNTER
STACK
POINTER
WATCHDOG
TIMER
JTAG TAP
TIMING AND
CONTROL
LCD
CONTROLLER/
DRIVER
PROGRAM
FLASH
MCU CONTROL
REGISTER
SRAM
ON-CHIP DEBUG
BOUNDARY-
SCAN
INSTRUCTION
REGISTER
TIMER/
COUNTERS
GENERAL
PURPOSE
REGISTERS
X
Y
Z
PROGRAMMING
LOGIC
INSTRUCTION
DECODER
INTERRUPT
UNIT
CONTROL
LINES
ALU
EEPROM
STATUS
REGISTER
AVR CPU
UNIVERSAL
SERIAL INTERFACE
SPI
USART
DATA REGISTER
PORTE
DATA DIR.
REG. PORTE
DATA REGISTER
PORTB
DATA DIR.
REG. PORTB
DATA REGISTER
PORTD
DATA DIR.
REG. PORTD
DATA REG. DATA DIR.
PORTG
REG. PORTG
PORTB DRIVERS
PORTD DRIVERS
PORTG DRIVERS
PORTE DRIVERS
PE0 - PE7
PB0 - PB7
PD0 - PD7
PG0 - PG4
4
2552KS–AVR–04/11
ATmega329/3290/649/6490
The Atmel® AVR® core combines a rich instruction set with 32 general purpose working regis-
ters. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two
independent registers to be accessed in one single instruction executed in one clock cycle. The
resulting architecture is more code efficient while achieving throughputs up to ten times faster
than conventional CISC microcontrollers.
The Atmel ATmega329/3290/649/6490 provides the following features: 32/64K bytes of In-Sys-
tem Programmable Flash with Read-While-Write capabilities, 1/2K bytes EEPROM, 2/4K byte
SRAM, 54/69 general purpose I/O lines, 32 general purpose working registers, a JTAG interface
for Boundary-scan, On-chip Debugging support and programming, a complete On-chip LCD
controller with internal contrast control, three flexible Timer/Counters with compare modes, inter-
nal and external interrupts, a serial programmable USART, Universal Serial Interface with Start
Condition Detector, an 8-channel, 10-bit ADC, a programmable Watchdog Timer with internal
Oscillator, an SPI serial port, and five software selectable power saving modes. The Idle mode
stops the CPU while allowing the SRAM, Timer/Counters, SPI port, and interrupt system to con-
tinue functioning. The Power-down mode saves the register contents but freezes the Oscillator,
disabling all other chip functions until the next interrupt or hardware reset. In Power-save mode,
the asynchronous timer and the LCD controller continues to run, allowing the user to maintain a
timer base and operate the LCD display while the rest of the device is sleeping. The ADC Noise
Reduction mode stops the CPU and all I/O modules except asynchronous timer, LCD controller
and ADC, to minimize switching noise during ADC conversions. In Standby mode, the crys-
tal/resonator Oscillator is running while the rest of the device is sleeping. This allows very fast
start-up combined with low-power consumption.
The device is manufactured using Atmel’s high density non-volatile memory technology. The
On-chip In-System re-Programmable (ISP) Flash allows the program memory to be repro-
grammed In-System through an SPI serial interface, by a conventional non-volatile memory
programmer, or by an On-chip Boot program running on the AVR core. The Boot program can
use any interface to download the application program in the Application Flash memory. Soft-
ware in the Boot Flash section will continue to run while the Application Flash section is updated,
providing true Read-While-Write operation. By combining an 8-bit RISC CPU with In-System
Self-Programmable Flash on a monolithic chip, the Atmel ATmega329/3290/649/6490 is a pow-
erful microcontroller that provides a highly flexible and cost effective solution to many embedded
control applications.
The Atmel ATmega329/3290/649/6490 is supported with a full suite of program and system
development tools including: C Compilers, Macro Assemblers, Program Debugger/Simulators,
In-Circuit Emulators, and Evaluation kits.
5
2552KS–AVR–04/11
ATmega329/3290/649/6490
2.2
Comparison between ATmega329, ATmega3290, ATmega649 and ATmega6490
The ATmega329, ATmega3290, ATmega649, and ATmega6490 differs only in memory sizes,
pin count and pinout. Table 2-1 on page 6 summarizes the different configurations for the four
devices.
Table 2-1.
Configuration Summary
LCD
Segments
General Purpose
I/O Pins
Device
Flash
EEPROM
1Kbytes
1K bytes
2Kbytes
2Kbytes
RAM
ATmega329
32Kbytes
2Kbytes
2Kbytes
4Kbytes
4Kbytes
4 x 25
4 x 40
4 x 25
4 x 40
54
69
54
69
ATmega3290 32Kbytes
ATmega649 64Kbytes
ATmega6490 64Kbytes
2.3
Pin Descriptions
The following section describes the I/O-pin special functions.
2.3.1
2.3.2
2.3.3
VCC
Digital supply voltage.
Ground.
GND
Port A (PA7..PA0)
Port A is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port A output buffers have symmetrical drive characteristics with both high sink and source
capability. As inputs, Port A pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port A pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Port A also serves the functions of various special features of the ATmega329/3290/649/6490
as listed on page 67.
2.3.4
Port B (PB7..PB0)
Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port B output buffers have symmetrical drive characteristics with both high sink and source
capability. As inputs, Port B pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port B pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Port B has better driving capabilities than the other ports.
Port B also serves the functions of various special features of the ATmega329/3290/649/6490
as listed on page 68.
6
2552KS–AVR–04/11
ATmega329/3290/649/6490
2.3.5
2.3.6
2.3.7
2.3.8
Port C (PC7..PC0)
Port C is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port C output buffers have symmetrical drive characteristics with both high sink and source
capability. As inputs, Port C pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port C pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Port C also serves the functions of special features of the ATmega329/3290/649/6490 as listed
on page 71.
Port D (PD7..PD0)
Port D is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port D output buffers have symmetrical drive characteristics with both high sink and source
capability. As inputs, Port D pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port D pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Port D also serves the functions of various special features of the ATmega329/3290/649/6490
as listed on page 73.
Port E (PE7..PE0)
Port E is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port E output buffers have symmetrical drive characteristics with both high sink and source
capability. As inputs, Port E pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port E pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Port E also serves the functions of various special features of the ATmega329/3290/649/6490
as listed on page 75.
Port F (PF7..PF0)
Port F serves as the analog inputs to the A/D Converter.
Port F also serves as an 8-bit bi-directional I/O port, if the A/D Converter is not used. Port pins
can provide internal pull-up resistors (selected for each bit). The Port F output buffers have sym-
metrical drive characteristics with both high sink and source capability. As inputs, Port F pins
that are externally pulled low will source current if the pull-up resistors are activated. The Port F
pins are tri-stated when a reset condition becomes active, even if the clock is not running. If the
JTAG interface is enabled, the pull-up resistors on pins PF7(TDI), PF5(TMS), and PF4(TCK) will
be activated even if a reset occurs.
Port F also serves the functions of the JTAG interface.
7
2552KS–AVR–04/11
ATmega329/3290/649/6490
2.3.9
Port G (PG5..PG0)
Port G is a 6-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port G output buffers have symmetrical drive characteristics with both high sink and source
capability. As inputs, Port G pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port G pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Port G also serves the functions of various special features of the ATmega329/3290/649/6490
as listed on page 75.
2.3.10
2.3.11
2.3.12
Port H (PH7..PH0)
Port H is a 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port H output buffers have symmetrical drive characteristics with both high sink and source
capability. As inputs, Port H pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port H pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Port H also serves the functions of various special features of the ATmega3290/6490 as listed
on page 75.
Port J (PJ6..PJ0)
Port J is a 7-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port J output buffers have symmetrical drive characteristics with both high sink and source capa-
bility. As inputs, Port J pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port J pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Port J also serves the functions of various special features of the ATmega3290/6490 as listed on
page 75.
RESET
Reset input. A low level on this pin for longer than the minimum pulse length will generate a
reset, even if the clock is not running. The minimum pulse length is given in “System and Reset
Characteristics” on page 330. Shorter pulses are not guaranteed to generate a reset.
2.3.13
2.3.14
2.3.15
XTAL1
XTAL2
AVCC
Input to the inverting Oscillator amplifier and input to the internal clock operating circuit.
Output from the inverting Oscillator amplifier.
AVCC is the supply voltage pin for Port F and the A/D Converter. It should be externally con-
nected to VCC, even if the ADC is not used. If the ADC is used, it should be connected to VCC
through a low-pass filter.
2.3.16
AREF
This is the analog reference pin for the A/D Converter.
8
2552KS–AVR–04/11
ATmega329/3290/649/6490
2.3.17
LCDCAP
An external capacitor (typical > 470nF) must be connected to the LCDCAP pin as shown in Fig-
ure 23-2. This capacitor acts as a reservoir for LCD power (VLCD). A large capacitance reduces
ripple on VLCD but increases the time until VLCD reaches its target value.
3. Resources
A comprehensive set of development tools, application notes and datasheets are available for
download on http://www.atmel.com/avr.
Note:
1.
4. Data Retention
Reliability Qualification results show that the projected data retention failure rate is much less
than 1 PPM over 20 years at 85°C or 100 years at 25°C.
5. About Code Examples
This documentation contains simple code examples that briefly show how to use various parts of
the device. These code examples assume that the part specific header file is included before
compilation. Be aware that not all C compiler vendors include bit definitions in the header files
and interrupt handling in C is compiler dependent. Please confirm with the C compiler documen-
tation for more details.
For I/O Registers located in extended I/O map, “IN”, “OUT”, “SBIS”, “SBIC”, “CBI”, and “SBI”
instructions must be replaced with instructions that allow access to extended I/O. Typically
“LDS” and “STS” combined with “SBRS”, “SBRC”, “SBR”, and “CBR”.
9
2552KS–AVR–04/11
ATmega329/3290/649/6490
6. Register Summary
Note:
Registers with bold type only available in ATmega3290/6490.
Address
Name
LCDDR19
LCDDR18
LCDDR17
LCDDR16
LCDDR15
LCDDR14
LCDDR13
LCDDR12
LCDDR11
LCDDR10
LCDDR09
LCDDR08
LCDDR07
LCDDR06
LCDDR05
LCDDR04
LCDDR03
LCDDR02
LCDDR01
LCDDR00
Reserved
Reserved
Reserved
Reserved
LCDCCR
LCDFRR
LCDCRB
LCDCRA
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
PORTJ
Bit 7
SEG339
Bit 6
SEG338
Bit 5
SEG337
Bit 4
SEG336
Bit 3
SEG335
Bit 2
SEG334
Bit 1
SEG333
Bit 0
SEG332
Page
244
244
244
244
244
244
244
244
244
244
244
244
244
244
244
244
244
244
244
244
(0xFF)
(0xFE)
(0xFD)
(0xFC)
(0xFB)
(0xFA)
(0xF9)
(0xF8)
(0xF7)
(0xF6)
(0xF5)
(0xF4)
(0xF3)
(0xF2)
(0xF1)
(0xF0)
(0xEF)
(0xEE)
(0xED)
(0xEC)
(0xEB)
(0xEA)
(0xE9)
(0xE8)
(0xE7)
(0xE6)
(0xE5)
(0xE4)
(0xE3)
(0xE2)
(0xE1)
(0xE0)
(0xDF)
(0xDE)
(0xDD)
(0xDC)
(0xDB)
(0xDA)
(0xD9)
(0xD8)
(0xD7)
(0xD6)
(0xD5)
(0xD4)
(0xD3)
(0xD2)
(0xD1)
(0xD0)
(0xCF)
(0xCE)
(0xCD)
(0xCC)
(0xCB)
(0xCA)
(0xC9)
(0xC8)
(0xC7)
(0xC6)
(0xC5)
(0xC4)
SEG331
SEG330
SEG329
SEG328
SEG327
SEG326
SEG325
SEG324
SEG323
SEG322
SEG321
SEG320
SEG319
SEG318
SEG317
SEG316
SEG315
SEG314
SEG313
SEG312
SEG311
SEG310
SEG309
SEG308
SEG307
SEG306
SEG305
SEG304
SEG303
SEG302
SEG301
SEG300
SEG239
SEG238
SEG237
SEG236
SEG235
SEG234
SEG233
SEG232
SEG231
SEG230
SEG229
SEG228
SEG227
SEG226
SEG225
SEG224
SEG223
SEG222
SEG221
SEG220
SEG219
SEG218
SEG217
SEG216
SEG215
SEG214
SEG213
SEG212
SEG211
SEG210
SEG209
SEG208
SEG207
SEG206
SEG205
SEG204
SEG203
SEG202
SEG201
SEG200
SEG139
SEG138
SEG137
SEG136
SEG135
SEG134
SEG133
SEG132
SEG131
SEG130
SEG129
SEG128
SEG127
SEG126
SEG125
SEG124
SEG123
SEG122
SEG121
SEG120
SEG119
SEG118
SEG117
SEG116
SEG115
SEG114
SEG113
SEG112
SEG111
SEG110
SEG109
SEG108
SEG107
SEG106
SEG105
SEG104
SEG103
SEG102
SEG101
SEG100
SEG039
SEG038
SEG037
SEG036
SEG035
SEG034
SEG033
SEG032
SEG031
SEG030
SEG029
SEG028
SEG027
SEG026
SEG025
SEG024
SEG023
SEG022
SEG021
SEG020
SEG019
SEG018
SEG017
SEG016
SEG015
SEG014
SEG013
SEG012
SEG011
SEG010
SEG009
SEG008
SEG007
SEG006
SEG005
SEG004
SEG003
SEG002
SEG001
SEG000
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
LCDDC2
LCDDC1
LCDDC0
-
LCDCC3
LCDCC2
LCDCC1
LCDCC0
243
241
239
239
-
LCDPS2
LCDPS1
LCDPS0
-
LCDCD2
LCDCD1
LCDCD0
LCDCS
LCD2B
LCDMUX1
LCDMUX0
LCDPM3
LCDPM2
LCDPM1
LCDPM0
LCDEN
LCDAB
-
LCDIF
LCDIE
-
-
LCDBL
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
PORTJ6
PORTJ5
PORTJ4
PORTJ3
PORTJ2
PORTJ1
PORTJ0
90
90
90
89
90
90
DDRJ
-
DDJ6
DDJ5
DDJ4
DDJ3
DDJ2
DDJ1
DDJ0
PINJ
-
PINJ6
PINJ5
PINJ4
PINJ3
PINJ2
PINJ1
PINJ0
PORTH
PORTH7
PORTH6
PORTH5
PORTH4
PORTH3
PORTH2
PORTH1
PORTH0
DDRH
DDH7
DDH6
DDH5
DDH4
DDH3
DDH2
DDH1
DDH0
PINH
PINH7
PINH6
PINH5
PINH4
PINH3
PINH2
PINH1
PINH0
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
UDR0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
USART0 Data Register
190
194
194
UBRR0H
UBRR0L
USART0 Baud Rate Register High
USART0 Baud Rate Register Low
10
2552KS–AVR–04/11
ATmega329/3290/649/6490
Address
Name
Reserved
UCSR0C
UCSR0B
UCSR0A
Reserved
Reserved
Reserved
Reserved
Reserved
USIDR
Bit 7
-
Bit 6
-
Bit 5
-
Bit 4
-
Bit 3
-
Bit 2
-
Bit 1
-
Bit 0
-
Page
(0xC3)
(0xC2)
(0xC1)
(0xC0)
(0xBF)
(0xBE)
(0xBD)
(0xBC)
(0xBB)
(0xBA)
(0xB9)
(0xB8)
(0xB7)
(0xB6)
(0xB5)
(0xB4)
(0xB3)
(0xB2)
(0xB1)
(0xB0)
(0xAF)
(0xAE)
(0xAD)
(0xAC)
(0xAB)
(0xAA)
(0xA9)
(0xA8)
(0xA7)
(0xA6)
(0xA5)
(0xA4)
(0xA3)
(0xA2)
(0xA1)
(0xA0)
(0x9F)
(0x9E)
(0x9D)
(0x9C)
(0x9B)
(0x9A)
(0x99)
(0x98)
(0x97)
(0x96)
(0x95)
(0x94)
(0x93)
(0x92)
(0x91)
(0x90)
(0x8F)
(0x8E)
(0x8D)
(0x8C)
(0x8B)
(0x8A)
(0x89)
(0x88)
(0x87)
(0x86)
(0x85)
-
UMSEL0
UPM01
UPM00
USBS0
UCSZ01
UCSZ00
UCPOL0
192
191
190
RXCIE0
TXCIE0
UDRIE0
RXEN0
TXEN0
UCSZ02
RXB80
TXB80
RXC0
TXC0
UDRE0
FE0
DOR0
UPE0
U2X0
MPCM0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
USI Data Register
203
203
204
USISR
USISIF
USIOIF
USIPF
USIDC
USICNT3
USICNT2
USICNT1
USICNT0
USICR
USISIE
USIOIE
USIWM1
USIWM0
USICS1
USICS0
USICLK
USITC
Reserved
ASSR
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
EXCLK
AS2
TCN2UB
OCR2UB
TCR2UB
155
Reserved
Reserved
OCR2A
-
-
-
-
-
-
-
-
-
-
Timer/Counter 2 Output Compare Register A
Timer/Counter2
155
155
TCNT2
Reserved
TCCR2A
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
OCR1BH
OCR1BL
OCR1AH
OCR1AL
ICR1H
-
-
-
-
-
-
-
-
FOC2A
WGM20
COM2A1
COM2A0
WGM21
CS22
CS21
CS20
153
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Timer/Counter1 Output Compare Register B High
Timer/Counter1 Output Compare Register B Low
Timer/Counter1 Output Compare Register A High
Timer/Counter1 Output Compare Register A Low
Timer/Counter1 Input Capture Register High
Timer/Counter1 Input Capture Register Low
Timer/Counter1 High
136
136
136
136
137
137
136
ICR1L
TCNT1H
11
2552KS–AVR–04/11
ATmega329/3290/649/6490
Address
Name
TCNT1L
Reserved
TCCR1C
TCCR1B
TCCR1A
DIDR1
Bit 7
Bit 6
Bit 5
Bit 4
Timer/Counter1 Low
Bit 3
Bit 2
Bit 1
Bit 0
Page
136
(0x84)
(0x83)
-
FOC1A
ICNC1
COM1A1
-
-
-
-
-
-
-
-
FOC1B
ICES1
COM1A0
-
-
-
-
-
CS12
-
-
-
135
134
132
210
227
(0x82)
-
WGM13
WGM12
CS11
WGM11
AIN1D
ADC1D
-
CS10
WGM10
AIN0D
ADC0D
-
(0x81)
COM1B1
COM1B0
-
(0x80)
-
-
ADC4D
-
-
ADC3D
-
-
(0x7F)
DIDR0
ADC7D
-
ADC6D
-
ADC5D
-
ADC2D
-
(0x7E)
Reserved
ADMUX
ADCSRB
ADCSRA
ADCH
(0x7D)
REFS1
-
REFS0
ACME
ADSC
ADLAR
-
MUX4
-
MUX3
-
MUX2
ADTS2
ADPS2
MUX1
ADTS1
ADPS1
MUX0
ADTS0
ADPS0
223
209/227
225
(0x7C)
(0x7B)
ADEN
ADATE
ADIF
ADIE
(0x7A)
ADC Data Register High
ADC Data Register Low
226
(0x79)
ADCL
226
(0x78)
Reserved
Reserved
Reserved
Reserved
PCMSK3
Reserved
Reserved
TIMSK2
TIMSK1
TIMSK0
PCMSK2
PCMSK1
PCMSK0
Reserved
EICRA
-
-
-
-
-
-
-
-
(0x77)
-
-
-
-
-
-
-
-
(0x76)
-
-
-
-
-
-
-
-
(0x75)
-
-
-
-
-
-
-
-
(0x74)
-
PCINT30
PCINT29
PCINT28
PCINT27
PCINT26
PCINT25
PCINT24
57
(0x73)
-
-
-
-
-
-
-
-
-
-
(0x72)
-
-
-
-
-
-
(0x71)
-
-
-
-
-
-
OCIE2A
OCIE1A
OCIE0A
PCINT17
PCINT9
PCINT1
-
TOIE2
TOIE1
TOIE0
PCINT16
PCINT8
PCINT0
-
156
137
106
57
(0x70)
-
-
ICIE1
-
-
OCIE1B
(0x6F)
-
-
-
-
-
-
(0x6E)
PCINT23
PCINT22
PCINT21
PCINT20
PCINT19
PCINT18
(0x6D)
PCINT15
PCINT14
PCINT13
PCINT12
PCINT11
PCINT10
58
(0x6C)
PCINT7
PCINT6
PCINT5
PCINT4
PCINT3
PCINT2
58
(0x6B)
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
(0x6A)
ISC01
-
ISC00
-
55
(0x69)
Reserved
Reserved
OSCCAL
Reserved
PRR
(0x68)
-
-
(0x67)
Oscillator Calibration Register [CAL7..0]
32
40
(0x66)
-
-
-
-
-
-
-
-
-
-
(0x65)
-
PRLCD
PRTIM1
PRSPI
PSUSART0
PRADC
(0x64)
Reserved
Reserved
CLKPR
-
-
-
-
-
-
-
-
(0x63)
-
-
-
-
-
CLKPS3
WDE
V
-
-
-
(0x62)
CLKPCE
-
-
-
WDCE
S
CLKPS2
WDP2
N
CLKPS1
WDP1
Z
CLKPS0
WDP0
C
33
48
12
14
14
(0x61)
WDTCR
SREG
-
I
-
-
(0x60)
T
H
0x3F (0x5F)
0x3E (0x5E)
0x3D (0x5D)
0x3C (0x5C)
0x3B (0x5B)
0x3A (0x5A)
0x39 (0x59)
0x38 (0x58)
0x37 (0x57)
0x36 (0x56)
0x35 (0x55)
0x34 (0x54)
0x33 (0x53)
0x32 (0x52)
0x31 (0x51)
0x30 (0x50)
0x2F (0x4F)
0x2E (0x4E)
0x2D (0x4D)
0x2C (0x4C)
0x2B (0x4B)
0x2A (0x4A)
0x29 (0x49)
0x28 (0x48)
0x27 (0x47)
0x26 (0x46)
SPH
Stack Pointer High
Stack Pointer Low
SPL
Reserved
Reserved
Reserved
Reserved
Reserved
SPMCSR
Reserved
MCUCR
MCUSR
SMCR
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
SPMIE
RWWSB
RWWSRE
BLBSET
PGWRT
PGERS
SPMEN
291
JTD
-
-
PUD
-
WDRF
SM2
-
-
BORF
SM1
-
IVSEL
EXTRF
SM0
-
IVCE
PORF
SE
52/87/254
-
-
-
JTRF
47
39
-
-
-
-
Reserved
OCDR
-
-
-
OCDR5
ACO
-
-
OCDR4
ACI
-
IDRD/OCDR7
OCDR6
ACBG
-
OCDR3
ACIE
-
OCDR2
ACIC
-
OCDR1
ACIS1
-
OCDR0
ACIS0
-
250
209
ACSR
ACD
-
Reserved
SPDR
-
SPI Data Register
167
167
165
25
SPSR
SPIF
SPIE
WCOL
SPE
-
-
-
-
-
SPI2X
SPR0
SPCR
DORD
MSTR
CPOL
CPHA
SPR1
GPIOR2
GPIOR1
Reserved
Reserved
OCR0A
TCNT0
General Purpose I/O Register
General Purpose I/O Register
25
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Timer/Counter0 Output Compare A
Timer/Counter0
105
105
12
2552KS–AVR–04/11
ATmega329/3290/649/6490
Address
Name
Reserved
TCCR0A
GTCCR
EEARH
EEARL
EEDR
Bit 7
Bit 6
-
Bit 5
-
Bit 4
-
Bit 3
-
Bit 2
Bit 1
-
Bit 0
-
Page
-
FOC0A
TSM
-
-
CS02
-
0x25 (0x45)
0x24 (0x44)
0x23 (0x43)
0x22 (0x42)
0x21 (0x41)
0x20 (0x40)
0x1F (0x3F)
0x1E (0x3E)
0x1D (0x3D)
0x1C (0x3C)
0x1B (0x3B)
0x1A (0x3A)
0x19 (0x39)
0x18 (0x38)
0x17 (0x37)
0x16 (0x36)
0x15 (0x35)
0x14 (0x34)
0x13 (0x33)
0x12 (0x32)
0x11 (0x31)
0x10 (0x30)
0x0F (0x2F)
0x0E (0x2E)
0x0D (0x2D)
0x0C (0x2C)
0x0B (0x2B)
0x0A (0x2A)
0x09 (0x29)
0x08 (0x28)
0x07 (0x27)
0x06 (0x26)
0x05 (0x25)
0x04 (0x24)
0x03 (0x23)
0x02 (0x22)
0x01 (0x21)
0x00 (0x20)
WGM00
COM0A1
COM0A0
WGM01
CS01
PSR2
CS00
PSR10
103
108/157
22
-
-
-
-
-
-
-
-
EEPROM Address Register High
EEPROM Address Register Low
EEPROM Data Register
22
22
EECR
-
-
-
-
EERIE
EEMWE
EEWE
EERE
22
GPIOR0
EIMSK
EIFR
General Purpose I/O Register
25
PCIE3
PCIF3
-
PCIE2
PCIF2
-
PCIE1
PCIF1
-
PCIE0
PCIF0
-
-
-
-
-
INT0
INTF0
-
55
-
-
56
Reserved
Reserved
Reserved
Reserved
TIFR2
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
OCF2A
OCF1A
OCF0A
PORTG1
DDG1
PING1
PORTF1
DDF1
PINF1
PORTE1
DDE1
PINE1
PORTD1
DDD1
PIND1
PORTC1
DDC1
PINC1
PORTB1
DDB1
PINB1
PORTA1
DDA1
PINA1
TOV2
TOV1
TOV0
PORTG0
DDG0
PING0
PORTF0
DDF0
PINF0
PORTE0
DDE0
PINE0
PORTD0
DDD0
PIND0
PORTC0
DDC0
PINC0
PORTB0
DDB0
PINB0
PORTA0
DDA0
PINA0
157
138
106
89
89
89
89
89
89
88
88
89
88
88
88
88
88
88
87
87
87
87
87
87
TIFR1
-
-
ICF1
-
-
-
OCF1B
-
TIFR0
-
-
-
-
PORTG
DDRG
PING
-
-
-
PORTG4
DDG4
PING4
PORTF4
DDF4
PINF4
PORTE4
DDE4
PINE4
PORTD4
DDD4
PIND4
PORTC4
DDC4
PINC4
PORTB4
DDB4
PINB4
PORTA4
DDA4
PINA4
PORTG3
DDG3
PING3
PORTF3
DDF3
PINF3
PORTE3
DDE3
PINE3
PORTD3
DDD3
PIND3
PORTC3
DDC3
PINC3
PORTB3
DDB3
PINB3
PORTA3
DDA3
PINA3
PORTG2
DDG2
PING2
PORTF2
DDF2
PINF2
PORTE2
DDE2
PINE2
PORTD2
DDD2
PIND2
PORTC2
DDC2
PINC2
PORTB2
DDB2
PINB2
PORTA2
DDA2
PINA2
-
-
-
-
-
PING5
PORTF5
DDF5
PINF5
PORTE5
DDE5
PINE5
PORTD5
DDD5
PIND5
PORTC5
DDC5
PINC5
PORTB5
DDB5
PINB5
PORTA5
DDA5
PINA5
PORTF
DDRF
PORTF7
DDF7
PINF7
PORTE7
DDE7
PINE7
PORTD7
DDD7
PIND7
PORTC7
DDC7
PINC7
PORTB7
DDB7
PINB7
PORTA7
DDA7
PINA7
PORTF6
DDF6
PINF6
PORTE6
DDE6
PINE6
PORTD6
DDD6
PIND6
PORTC6
DDC6
PINC6
PORTB6
DDB6
PINB6
PORTA6
DDA6
PINA6
PINF
PORTE
DDRE
PINE
PORTD
DDRD
PIND
PORTC
DDRC
PINC
PORTB
DDRB
PINB
PORTA
DDRA
PINA
Note:
1. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses
should never be written.
2. I/O Registers within the address range 0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. In these
registers, the value of single bits can be checked by using the SBIS and SBIC instructions.
3. Some of the Status Flags are cleared by writing a logical one to them. Note that, unlike most other AVRs, the CBI and SBI
instructions will only operate on the specified bit, and can therefore be used on registers containing such Status Flags. The
CBI and SBI instructions work with registers 0x00 to 0x1F only.
4. When using the I/O specific commands IN and OUT, the I/O addresses 0x00 - 0x3F must be used. When addressing I/O
Registers as data space using LD and ST instructions, 0x20 must be added to these addresses. The
ATmega329/3290/649/6490 is a complex microcontroller with more peripheral units than can be supported within the 64
location reserved in Opcode for the IN and OUT instructions. For the Extended I/O space from 0x60 - 0xFF in SRAM, only
the ST/STS/STD and LD/LDS/LDD instructions can be used.
13
2552KS–AVR–04/11
ATmega329/3290/649/6490
7. Instruction Set Summary
Mnemonics
Operands
Description
Operation
Flags
#Clocks
ARITHMETIC AND LOGIC INSTRUCTIONS
ADD
Rd, Rr
Rd, Rr
Rdl,K
Rd, Rr
Rd, K
Rd, Rr
Rd, K
Rdl,K
Rd, Rr
Rd, K
Rd, Rr
Rd, K
Rd, Rr
Rd
Add two Registers
Rd ← Rd + Rr
Z,C,N,V,H
Z,C,N,V,H
Z,C,N,V,S
Z,C,N,V,H
Z,C,N,V,H
Z,C,N,V,H
Z,C,N,V,H
Z,C,N,V,S
Z,N,V
1
1
2
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
ADC
Add with Carry two Registers
Add Immediate to Word
Subtract two Registers
Subtract Constant from Register
Subtract with Carry two Registers
Subtract with Carry Constant from Reg.
Subtract Immediate from Word
Logical AND Registers
Logical AND Register and Constant
Logical OR Registers
Rd ← Rd + Rr + C
Rdh:Rdl ← Rdh:Rdl + K
Rd ← Rd - Rr
ADIW
SUB
SUBI
SBC
Rd ← Rd - K
Rd ← Rd - Rr - C
Rd ← Rd - K - C
Rdh:Rdl ← Rdh:Rdl - K
Rd ← Rd • Rr
SBCI
SBIW
AND
ANDI
OR
Rd ← Rd • K
Z,N,V
Rd ← Rd v Rr
Z,N,V
ORI
Logical OR Register and Constant
Exclusive OR Registers
One’s Complement
Rd ← Rd v K
Z,N,V
EOR
COM
NEG
SBR
Rd ← Rd ⊕ Rr
Z,N,V
Rd ← 0xFF − Rd
Rd ← 0x00 − Rd
Rd ← Rd v K
Z,C,N,V
Z,C,N,V,H
Z,N,V
Rd
Two’s Complement
Rd,K
Rd,K
Rd
Set Bit(s) in Register
CBR
Clear Bit(s) in Register
Increment
Rd ← Rd • (0xFF - K)
Rd ← Rd + 1
Z,N,V
INC
Z,N,V
DEC
Rd
Decrement
Rd ← Rd − 1
Z,N,V
TST
Rd
Test for Zero or Minus
Clear Register
Rd ← Rd • Rd
Z,N,V
CLR
Rd
Rd ← Rd ⊕ Rd
Rd ← 0xFF
Z,N,V
SER
Rd
Set Register
None
MUL
Rd, Rr
Rd, Rr
Rd, Rr
Rd, Rr
Rd, Rr
Rd, Rr
Multiply Unsigned
R1:R0 ← Rd x Rr
R1:R0 ← Rd x Rr
R1:R0 ← Rd x Rr
R1:R0 ← (Rd x Rr) << 1
R1:R0 ← (Rd x Rr) << 1
R1:R0 ← (Rd x Rr) << 1
Z,C
MULS
MULSU
FMUL
FMULS
FMULSU
Multiply Signed
Z,C
Multiply Signed with Unsigned
Fractional Multiply Unsigned
Fractional Multiply Signed
Fractional Multiply Signed with Unsigned
Z,C
Z,C
Z,C
Z,C
BRANCH INSTRUCTIONS
RJMP
IJMP
k
Relative Jump
PC ← PC + k + 1
None
None
None
None
None
None
None
I
2
2
Indirect Jump to (Z)
PC ← Z
JMP
k
k
Direct Jump
PC ← k
3
RCALL
ICALL
CALL
RET
Relative Subroutine Call
Indirect Call to (Z)
PC ← PC + k + 1
3
PC ← Z
3
k
Direct Subroutine Call
Subroutine Return
PC ← k
4
PC ← STACK
4
RETI
Interrupt Return
PC ← STACK
4
CPSE
CP
Rd,Rr
Compare, Skip if Equal
Compare
if (Rd = Rr) PC ← PC + 2 or 3
Rd − Rr
None
Z, N,V,C,H
Z, N,V,C,H
Z, N,V,C,H
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
1/2/3
1
Rd,Rr
CPC
Rd,Rr
Compare with Carry
Rd − Rr − C
1
CPI
Rd,K
Compare Register with Immediate
Skip if Bit in Register Cleared
Skip if Bit in Register is Set
Skip if Bit in I/O Register Cleared
Skip if Bit in I/O Register is Set
Branch if Status Flag Set
Branch if Status Flag Cleared
Branch if Equal
Rd − K
1
SBRC
SBRS
SBIC
SBIS
Rr, b
if (Rr(b)=0) PC ← PC + 2 or 3
if (Rr(b)=1) PC ← PC + 2 or 3
if (P(b)=0) PC ← PC + 2 or 3
if (P(b)=1) PC ← PC + 2 or 3
if (SREG(s) = 1) then PC←PC+k + 1
if (SREG(s) = 0) then PC←PC+k + 1
if (Z = 1) then PC ← PC + k + 1
if (Z = 0) then PC ← PC + k + 1
if (C = 1) then PC ← PC + k + 1
if (C = 0) then PC ← PC + k + 1
if (C = 0) then PC ← PC + k + 1
if (C = 1) then PC ← PC + k + 1
if (N = 1) then PC ← PC + k + 1
if (N = 0) then PC ← PC + k + 1
if (N ⊕ V= 0) then PC ← PC + k + 1
if (N ⊕ V= 1) then PC ← PC + k + 1
if (H = 1) then PC ← PC + k + 1
if (H = 0) then PC ← PC + k + 1
if (T = 1) then PC ← PC + k + 1
1/2/3
1/2/3
1/2/3
1/2/3
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
Rr, b
P, b
P, b
s, k
s, k
k
BRBS
BRBC
BREQ
BRNE
BRCS
BRCC
BRSH
BRLO
BRMI
BRPL
BRGE
BRLT
BRHS
BRHC
BRTS
k
Branch if Not Equal
k
Branch if Carry Set
k
Branch if Carry Cleared
Branch if Same or Higher
Branch if Lower
k
k
k
Branch if Minus
k
Branch if Plus
k
Branch if Greater or Equal, Signed
Branch if Less Than Zero, Signed
Branch if Half Carry Flag Set
Branch if Half Carry Flag Cleared
Branch if T Flag Set
k
k
k
k
14
2552KS–AVR–04/11
ATmega329/3290/649/6490
Mnemonics
Operands
Description
Operation
Flags
#Clocks
BRTC
BRVS
BRVC
BRIE
k
k
k
k
k
Branch if T Flag Cleared
if (T = 0) then PC ← PC + k + 1
if (V = 1) then PC ← PC + k + 1
if (V = 0) then PC ← PC + k + 1
if ( I = 1) then PC ← PC + k + 1
if ( I = 0) then PC ← PC + k + 1
None
1/2
1/2
1/2
1/2
1/2
Branch if Overflow Flag is Set
Branch if Overflow Flag is Cleared
Branch if Interrupt Enabled
None
None
None
None
BRID
Branch if Interrupt Disabled
BIT AND BIT-TEST INSTRUCTIONS
SBI
P,b
P,b
Rd
Rd
Rd
Rd
Rd
Rd
s
Set Bit in I/O Register
Clear Bit in I/O Register
Logical Shift Left
I/O(P,b) ← 1
None
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
CBI
I/O(P,b) ← 0
None
LSL
Rd(n+1) ← Rd(n), Rd(0) ← 0
Z,C,N,V
LSR
ROL
ROR
ASR
SWAP
BSET
BCLR
BST
BLD
SEC
CLC
SEN
CLN
SEZ
CLZ
SEI
Logical Shift Right
Rd(n) ← Rd(n+1), Rd(7) ← 0
Z,C,N,V
Rotate Left Through Carry
Rotate Right Through Carry
Arithmetic Shift Right
Swap Nibbles
Rd(0)←C,Rd(n+1)← Rd(n),C←Rd(7)
Z,C,N,V
Rd(7)←C,Rd(n)← Rd(n+1),C←Rd(0)
Z,C,N,V
Rd(n) ← Rd(n+1), n=0..6
Z,C,N,V
Rd(3..0)←Rd(7..4),Rd(7..4)←Rd(3..0)
None
Flag Set
SREG(s) ← 1
SREG(s) ← 0
T ← Rr(b)
Rd(b) ← T
C ← 1
SREG(s)
s
Flag Clear
SREG(s)
Rr, b
Rd, b
Bit Store from Register to T
Bit load from T to Register
Set Carry
T
None
C
C
N
N
Z
Clear Carry
C ← 0
Set Negative Flag
N ← 1
Clear Negative Flag
Set Zero Flag
N ← 0
Z ← 1
Clear Zero Flag
Z ← 0
Z
Global Interrupt Enable
Global Interrupt Disable
Set Signed Test Flag
Clear Signed Test Flag
Set Twos Complement Overflow.
Clear Twos Complement Overflow
Set T in SREG
I ← 1
I
CLI
I ← 0
I
SES
CLS
SEV
CLV
SET
CLT
SEH
CLH
S ← 1
S
S
V
V
T
S ← 0
V ← 1
V ← 0
T ← 1
Clear T in SREG
T ← 0
T
Set Half Carry Flag in SREG
Clear Half Carry Flag in SREG
H ← 1
H
H
H ← 0
DATA TRANSFER INSTRUCTIONS
MOV
MOVW
LDI
LD
Rd, Rr
Rd, Rr
Rd, K
Move Between Registers
Copy Register Word
Rd ← Rr
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
-
Rd+1:Rd ← Rr+1:Rr
Load Immediate
Rd ← K
Rd, X
Load Indirect
Rd ← (X)
LD
Rd, X+
Rd, - X
Rd, Y
Load Indirect and Post-Inc.
Load Indirect and Pre-Dec.
Load Indirect
Rd ← (X), X ← X + 1
X ← X - 1, Rd ← (X)
Rd ← (Y)
LD
LD
LD
Rd, Y+
Rd, - Y
Rd,Y+q
Rd, Z
Load Indirect and Post-Inc.
Load Indirect and Pre-Dec.
Load Indirect with Displacement
Load Indirect
Rd ← (Y), Y ← Y + 1
Y ← Y - 1, Rd ← (Y)
Rd ← (Y + q)
LD
LDD
LD
Rd ← (Z)
LD
Rd, Z+
Rd, -Z
Rd, Z+q
Rd, k
Load Indirect and Post-Inc.
Load Indirect and Pre-Dec.
Load Indirect with Displacement
Load Direct from SRAM
Store Indirect
Rd ← (Z), Z ← Z+1
Z ← Z - 1, Rd ← (Z)
Rd ← (Z + q)
LD
LDD
LDS
ST
Rd ← (k)
X, Rr
(X) ← Rr
ST
X+, Rr
- X, Rr
Y, Rr
Store Indirect and Post-Inc.
Store Indirect and Pre-Dec.
Store Indirect
(X) ← Rr, X ← X + 1
X ← X - 1, (X) ← Rr
(Y) ← Rr
ST
ST
ST
Y+, Rr
- Y, Rr
Y+q,Rr
Z, Rr
Store Indirect and Post-Inc.
Store Indirect and Pre-Dec.
Store Indirect with Displacement
Store Indirect
(Y) ← Rr, Y ← Y + 1
Y ← Y - 1, (Y) ← Rr
(Y + q) ← Rr
ST
STD
ST
(Z) ← Rr
ST
Z+, Rr
-Z, Rr
Z+q,Rr
k, Rr
Store Indirect and Post-Inc.
Store Indirect and Pre-Dec.
Store Indirect with Displacement
Store Direct to SRAM
(Z) ← Rr, Z ← Z + 1
Z ← Z - 1, (Z) ← Rr
(Z + q) ← Rr
ST
STD
STS
LPM
LPM
LPM
SPM
(k) ← Rr
Load Program Memory
Load Program Memory
Load Program Memory and Post-Inc
Store Program Memory
R0 ← (Z)
Rd, Z
Rd ← (Z)
Rd, Z+
Rd ← (Z), Z ← Z+1
(Z) ← R1:R0
15
2552KS–AVR–04/11
ATmega329/3290/649/6490
Mnemonics
Operands
Description
Operation
Flags
#Clocks
IN
Rd, P
In Port
Rd ← P
None
1
1
2
2
OUT
P, Rr
Rr
Out Port
P ← Rr
None
None
None
PUSH
POP
Push Register on Stack
Pop Register from Stack
STACK ← Rr
Rd ← STACK
Rd
MCU CONTROL INSTRUCTIONS
NOP
No Operation
Sleep
None
None
None
None
1
1
SLEEP
WDR
(see specific descr. for Sleep function)
(see specific descr. for WDR/timer)
For On-chip Debug Only
Watchdog Reset
Break
1
BREAK
N/A
16
2552KS–AVR–04/11
ATmega329/3290/649/6490
8. Ordering Information
8.1
ATmega329
Speed (MHz)(3)
Power Supply
Ordering Code(2)
Package Type(1)
Operational Range
ATmega329V-8AU
64A
64A
64M1
64M1
ATmega329V-8AUR(4)
ATmega329V-8MU
ATmega329V-8MUR(4)
Industrial
(-40°C to 85°C)
8
1.8 - 5.5V
ATmega329-16AU
64A
64A
64M1
64M1
ATmega329-16AUR(4)
ATmega329-16MU
ATmega329-16MUR(4)
Industrial
(-40°C to 85°C)
16
2.7 - 5.5V
Notes: 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information
and minimum quantities.
2. Pb-free packaging alternative, complies to the European Directive for Restriction of Hazardous Substances (RoHS direc-
tive). Also Halide free and fully Green.
3. For Speed vs. VCC see Figure 28-1 on page 328 and Figure 28-2 on page 328.
4. Tape & Reel
Package Type
64A
64-lead, 14 x 14 x 1.0 mm, Thin Profile Plastic Quad Flat Package (TQFP)
64M1
100A
64-pad, 9 x 9 x 1.0 mm, Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)
100-lead, 14 x 14 x 1.0 mm, 0.5 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
17
2552KS–AVR–04/11
ATmega329/3290/649/6490
8.2
ATmega3290
Speed (MHz)(3)
Power Supply
Ordering Code(2)
Package Type(1)
Operational Range
ATmega3290V-8AU
100A
100A
Industrial
(-40°C to 85°C)
8
1.8 - 5.5V
ATmega3290V-8AUR(4)
ATmega3290-16AU
100A
100A
Industrial
(-40°C to 85°C)
16
2.7 - 5.5V
ATmega3290-16AUR(4)
Notes: 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information
and minimum quantities.
2. Pb-free packaging alternative, complies to the European Directive for Restriction of Hazardous Substances (RoHS direc-
tive). Also Halide free and fully Green.
3. For Speed vs. VCC see Figure 28-1 on page 328 and Figure 28-2 on page 328.
4. Tape & Reel
Package Type
64A
64-lead, 14 x 14 x 1.0 mm, Thin Profile Plastic Quad Flat Package (TQFP)
64M1
100A
64-pad, 9 x 9 x 1.0 mm, Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)
100-lead, 14 x 14 x 1.0 mm, 0.5 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
18
2552KS–AVR–04/11
ATmega329/3290/649/6490
8.3
ATmega649
Speed (MHz)(3)
Power Supply
Ordering Code(2)
Package Type(1)
Operational Range
ATmega649V-8AU
64A
64A
64M1
64M1
ATmega649V-8AUR(4)
ATmega649V-8MU
ATmega649V-8MUR(4)
Industrial
(-40°C to 85°C)
8
1.8 - 5.5V
ATmega649-16AU
64A
64A
64M1
64M1
ATmega649-16AUR(4)
ATmega649-16MU
ATmega649-16MUR(4)
Industrial
(-40°C to 85°C)
16
2.7 - 5.5V
Notes: 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information
and minimum quantities.
2. Pb-free packaging alternative, complies to the European Directive for Restriction of Hazardous Substances (RoHS direc-
tive). Also Halide free and fully Green.
3. For Speed vs. VCC see Figure 28-1 on page 328 and Figure 28-2 on page 328.
4. Tape & Reel
Package Type
64A
64-lead, 14 x 14 x 1.0 mm, Thin Profile Plastic Quad Flat Package (TQFP)
64M1
100A
64-pad, 9 x 9 x 1.0 mm, Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)
100-lead, 14 x 14 x 1.0 mm, 0.5 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
19
2552KS–AVR–04/11
ATmega329/3290/649/6490
8.4
ATmega6490
Speed (MHz)(3)
Power Supply
Ordering Code(2)
Package Type(1)
Operational Range
ATmega6490V-8AU
100A
100A
Industrial
(-40°C to 85°C)
8
1.8 - 5.5V
ATmega6490V-8AUR(4)
ATmega6490-16AU
100A
100A
Industrial
(-40°C to 85°C)
16
2.7 - 5.5V
ATmega6490-16AUR(4)
Notes: 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information
and minimum quantities.
2. Pb-free packaging alternative, complies to the European Directive for Restriction of Hazardous Substances (RoHS direc-
tive). Also Halide free and fully Green.
3. For Speed Grades see Figure 28-1 on page 328 and Figure 28-2 on page 328.
4. Tape & Reel
Package Type
64A
64-lead, 14 x 14 x 1.0 mm, Thin Profile Plastic Quad Flat Package (TQFP)
64M1
100A
64-pad, 9 x 9 x 1.0 mm, Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)
100-lead, 14 x 14 x 1.0 mm, 0.5 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
20
2552KS–AVR–04/11
ATmega329/3290/649/6490
9. Packaging Information
9.1
64A
PIN 1
B
e
PIN 1 IDENTIFIER
E1
E
D1
D
C
0°~7°
A2
A
A1
L
COMMON DIMENSIONS
(Unit of Measure = mm)
MIN
–
MAX
1.20
NOM
–
NOTE
SYMBOL
A
A1
A2
D
0.05
0.95
15.75
13.90
15.75
13.90
0.30
0.09
0.45
–
0.15
1.00
16.00
14.00
16.00
14.00
–
1.05
16.25
D1
E
14.10 Note 2
16.25
Notes:
E1
B
14.10 Note 2
0.45
1.This package conforms to JEDEC reference MS-026, Variation AEB.
2. Dimensions D1 and E1 do not include mold protrusion. Allowable
protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum
plastic body size dimensions including mold mismatch.
C
–
0.20
3. Lead coplanarity is 0.10 mm maximum.
L
–
0.75
e
0.80 TYP
2010-10-20
TITLE
DRAWING NO. REV.
2325 Orchard Parkway
San Jose, CA 95131
64A, 64-lead, 14 x 14 mm Body Size, 1.0 mm Body Thickness,
0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
64A
C
R
21
2552KS–AVR–04/11
ATmega329/3290/649/6490
9.2
64M1
D
Marked Pin# 1 ID
E
SEATING PLANE
C
A1
TOP VIEW
A
K
0.08
C
L
Pin #1 Corner
SIDE VIEW
D2
Pin #1
Triangle
Option A
1
2
3
COMMON DIMENSIONS
(Unit of Measure = mm)
MIN
0.80
–
MAX
1.00
0.05
0.30
9.10
NOM
0.90
0.02
0.25
9.00
NOTE
SYMBOL
E2
Option B
Option C
A
Pin #1
Chamfer
(C 0.30)
A1
b
0.18
8.90
D
D2
E
5.20
5.40
9.00
5.60
9.10
K
Pin #1
Notch
(0.20 R)
8.90
e
b
E2
e
5.20
5.40
0.50 BSC
0.40
5.60
BOTTOM VIEW
L
0.35
1.25
0.45
1.55
K
1.40
Notes:
1. JEDEC Standard MO-220, (SAW Singulation) Fig. 1, VMMD.
2. Dimension and tolerance conform to ASMEY14.5M-1994.
2010-10-19
TITLE
DRAWING NO. REV.
64M1
2325 Orchard Parkway
San Jose, CA 95131
64M1, 64-pad, 9 x 9 x 1.0 mm Body, Lead Pitch 0.50 mm,
5.40 mm Exposed Pad, Micro Lead Frame Package (MLF)
H
R
22
2552KS–AVR–04/11
ATmega329/3290/649/6490
9.3
100A
PIN 1
B
PIN 1 IDENTIFIER
E1
E
e
D1
D
C
0°~7°
A2
A
A1
L
COMMON DIMENSIONS
(Unit of Measure = mm)
MIN
–
MAX
1.20
NOM
NOTE
SYMBOL
A
–
–
A1
A2
D
0.05
0.95
15.75
13.90
15.75
13.90
0.17
0.09
0.45
0.15
1.00
16.00
14.00
16.00
14.00
–
1.05
16.25
D1
E
14.10 Note 2
16.25
Notes:
E1
B
14.10 Note 2
0.27
1. This package conforms to JEDEC reference MS-026, Variation AED.
2. Dimensions D1 and E1 do not include mold protrusion. Allowable
protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum
plastic body size dimensions including mold mismatch.
C
–
0.20
3. Lead coplanarity is 0.08 mm maximum.
L
–
0.75
e
0.50 TYP
2010-10-20
TITLE
DRAWING NO. REV.
2325 Orchard Parkway
San Jose, CA 95131
100A, 100-lead, 14 x 14 mm Body Size, 1.0 mm Body Thickness,
0.5 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
100A
D
R
23
2552KS–AVR–04/11
ATmega329/3290/649/6490
10. Errata
10.1 ATmega329
10.1.1
ATmega329 rev. C
• Interrupts may be lost when writing the timer registers in the asynchronous timer
1. Interrupts may be lost when writing the timer registers in the asynchronous timer
The interrupt will be lost if a timer register that is synchronous timer clock is written when the
asynchronous Timer/Counter register (TCNTx) is 0x00.
Problem Fix/Wortkaround
Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor
0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronous
Timer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx).
10.1.2
10.1.3
ATmega329 rev. B
Not sampled.
ATmega329 rev. A
• LCD contrast voltage too high
• Interrupts may be lost when writing the timer registers in the asynchronous timer
1. LCD contrast voltage too high
When the LCD is active and using low power waveform, the LCD contrast voltage can be too
high. This occurs when VCC is higher than VLCD, and when using low LCD drivetime.
Problem Fix/Workaround
There are several possible workarounds:
- Use normal waveform instead of low power waveform
- Use drivetime of 375 µs or longer
2. Interrupts may be lost when writing the timer registers in the asynchronous timer
The interrupt will be lost if a timer register that is synchronous timer clock is written when the
asynchronous Timer/Counter register (TCNTx) is 0x00.
Problem Fix/Wortkaround
Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor
0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronous
Timer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx).
24
2552KS–AVR–04/11
ATmega329/3290/649/6490
10.2 ATmega3290
10.2.1
ATmega3290 rev. C
• Interrupts may be lost when writing the timer registers in the asynchronous timer
1. Interrupts may be lost when writing the timer registers in the asynchronous timer
The interrupt will be lost if a timer register that is synchronous timer clock is written when the
asynchronous Timer/Counter register (TCNTx) is 0x00.
Problem Fix/Wortkaround
Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor
0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronous
Timer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx).
10.2.2
10.2.3
ATmega3290 rev. B
Not sampled.
ATmega3290 rev. A
• LCD contrast voltage too high
• Interrupts may be lost when writing the timer registers in the asynchronous timer
1. LCD contrast voltage too high
When the LCD is active and using low power waveform, the LCD contrast voltage can be too
high. This occurs when VCC is higher than VLCD, and when using low LCD drivetime.
Problem Fix/Workaround
There are several possible workarounds:
- Use normal waveform instead of low power waveform
- Use drivetime of 375 µs or longer
2. Interrupts may be lost when writing the timer registers in the asynchronous timer
The interrupt will be lost if a timer register that is synchronous timer clock is written when the
asynchronous Timer/Counter register (TCNTx) is 0x00.
Problem Fix/Wortkaround
Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor
0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronous
Timer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx).
25
2552KS–AVR–04/11
ATmega329/3290/649/6490
10.3 ATmega649
10.3.1
ATmega649 rev. A
• Interrupts may be lost when writing the timer registers in the asynchronous timer
1. Interrupts may be lost when writing the timer registers in the asynchronous timer
The interrupt will be lost if a timer register that is synchronous timer clock is written when the
asynchronous Timer/Counter register (TCNTx) is 0x00.
Problem Fix/Wortkaround
Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor
0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronous
Timer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx).
10.4 ATmega6490
10.4.1
ATmega6490 rev. A
• Interrupts may be lost when writing the timer registers in the asynchronous timer
1. Interrupts may be lost when writing the timer registers in the asynchronous timer
The interrupt will be lost if a timer register that is synchronous timer clock is written when the
asynchronous Timer/Counter register (TCNTx) is 0x00.
Problem Fix/Wortkaround
Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor
0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronous
Timer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx).
26
2552KS–AVR–04/11
ATmega329/3290/649/6490
11. Datasheet Revision History
Please note that the referring page numbers in this section are referring to this document.The
referring revision in this section are referring to the document revision.
11.1 Rev. 2552K – 04/11
1.
Removed “Preliminary” from the front page.
2.
3.
4.
5.
Removed “Disclaimer Section” from the datasheet.
Updated Table 28-5 on page 330 “BODLEVEL Fuse Coding(1)” .
Updated Table 28-8 on page 334 “LCD Controller Characteristics” .
Updated “Ordering Information” on page 372 to include “Tape & Reel” devices.
The “AI” and “MI” devices removed.
6.
7.
Updated “Errata” on page 379.
Updated the datasheet according to the Atmel new brand style guide, including
the last page.
11.2 Rev. 2552J – 08/07
1.
2.
3.
4.
5.
6.
Updated “Features” on page 1.
Added “Data Retention” on page 9.
Updated “Serial Programming Algorithm” on page 309.
Updated “Speed Grades” on page 328.
Updated “System and Reset Characteristics” on page 330.
Moved Register Descriptions to the end of each chapter.
11.3 Rev. 2552I – 04/07
1.
2.
Updated date in backpage
Updated column in Table 28-5 on page 330.
11.4 Rev. 2552H – 11/06
1.
2.
Updated Table 28-7 on page 333.
Updated note in Table 28-7 on page 333 and Table 28-2 on page 329.
27
2552KS–AVR–04/11
ATmega329/3290/649/6490
11.5 Rev. 2552G – 07/06
1.
Updated Table 14-2 on page 104, Table 14-4 on page 104, Table 16-3 on
page 133, Table 16-5 on page 134, Table 16-5 on page 134, Table 17-2 on
page 153 and Table 17-4 on page 154.
2.
3.
4.
5.
Updated “Fast PWM Mode” on page 124.
Updated Features in “USI – Universal Serial Interface” on page 195.
Added “Clock speed considerations.” on page 202.
“Errata” on page 379.
11.6 Rev. 2552F – 06/06
1.
2.
3.
Updated “Calibrated Internal RC Oscillator” on page 29.
Updated “OSCCAL – Oscillator Calibration Register” on page 32
Added Table 28-2 on page 329.
11.7 Rev. 2552E – 04/06
1.
Updated “Calibrated Internal RC Oscillator” on page 29.
Updated “Errata” on page 379.
11.8 Rev. 2552D – 03/06
1.
11.9 Rev. 2552C – 03/06
1.
2.
3.
4.
Added “Resources” on page 9.
Added Addresses in Registers.
Updated number of General Purpose I/O pins.
Updated code example in “Bit 0 – IVCE: Interrupt Vector Change Enable”
on page 53.
5.
6.
7.
Updated Introduction in “I/O-Ports” on page 59.
Updated “SPI – Serial Peripheral Interface” on page 158.
Updated “Bit 6 – ACBG: Analog Comparator Bandgap Select” on page
209.
8.
9.
Updated Features in “Analog to Digital Converter” on page 211.
Updated “Prescaling and Conversion Timing” on page 214.
10. Updated features in “LCD Controller” on page 228.
11. Updated “ATmega329/3290/649/6490 Boot Loader Parameters” on page
290.
12. Updated “DC Characteristics” on page 310.
13. Updated “” on page 334.
28
2552KS–AVR–04/11
ATmega329/3290/649/6490
11.10 Rev. 2552B – 05/05
1.
MLF-package alternative changed to “Quad Flat No-Lead/Micro Lead
Frame Package QFN/MLF”.
2.
3.
Added “Pin Change Interrupt Timing” on page 54.
Updated Table 23-6 on page 242, Table 23-7 on page 243 and Table 27-15
on page 310.
4.
5.
6.
7.
8.
Added Figure 27-12 on page 312.
Updated Figure 22-9 on page 219 and Figure 27-5 on page 304.
Updated algorithm “Enter Programming Mode” on page 299.
Added “Supply Current of I/O modules” on page 340.
Updated “Ordering Information” on page 372.
11.11 Rev. 2552A –11/04
1.
Initial version.
29
2552KS–AVR–04/11
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
USA
Tel: (+1)(408) 441-0311
Fax: (+1)(408) 487-2600
www.atmel.com
Atmel Asia Limited
Unit 1-5 & 16, 19/F
BEA Tower, Millennium City 5
418 Kwun Tong Road
Kwun Tong, Kowloon
HONG KONG
Atmel Munich GmbH
Business Campus
Parkring 4
D-85748 Garching b. Munich
GERMANY
Atmel Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
JAPAN
Tel: (+81)(3) 3523-3551
Fax: (+81)(3) 3523-7581
Tel: (+49) 89-31970-0
Fax: (+49) 89-3194621
Tel: (+852) 2245-6100
Fax: (+852) 2722-1369
© 2011 Atmel Corporation. All rights reserved.
Atmel®, Atmel logo and combinations thereof, AVR® and others are registered trademarks or trademarks of Atmel Corporation or its
subsidiaries. Other terms and product names may be trademarks of others.
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to
any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL
TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY
EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT,
INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROF-
ITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or com-
pleteness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice.
Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suit-
able for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applica-
tions intended to support or sustain life.
2552KS–AVR–04/11
相关型号:
ATMEGA32A-AU-SL383
Microcontroller, 8-Bit, FLASH, AVR RISC CPU, 16MHz, CMOS, PQFP44, 10 X 10 MM, 1 MM HEIGHT, 0.80 MM PITCH, GREEN, PLASTIC, MS-026ACB, TQFP-44
ATMEL
ATMEGA32A-AUR
RISC Microcontroller, 8-Bit, FLASH, AVR RISC CPU, 16MHz, CMOS, PQFP44, 10 X 10 MM, 1 MM HEIGHT, 0.80 MM PITCH, GREEN, PLASTIC, MS-026ACB, TQFP-44
ATMEL
ATMEGA32A-MU-SL383
Microcontroller, 8-Bit, FLASH, AVR RISC CPU, 16MHz, CMOS, PQCC44, 7 X 7 MM, 1 MM HEIGHT, 0.50 MM PITCH, GREEN, PLASTIC, MO-220VKKD-3, VQFN-44
ATMEL
©2020 ICPDF网 联系我们和版权申明