AT25040B-SSPD-T [MICROCHIP]
AT25040B-SSPD-T;
| 型号： | AT25040B-SSPD-T |
| 厂家： | 
MICROCHIP |
| 描述： | AT25040B-SSPD-T 可编程只读存储器 电动程控只读存储器 电可擦编程只读存储器 光电二极管 |
| 文件： | 总23页 (文件大小：867K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
AT25010B, AT25020B, and AT25040B
SPI Automotive Temperature Serial EEPROMs
1K (128 x 8), 2K (256 x 8), 4k (512 x 8)
DATASHEET
Features
Serial Peripheral Interface (SPI) Compatible
Supports SPI Modes 0 (0,0) and 3 (1,1)
̶
Datasheet describes Mode 0 operation
Low-voltage, Medium-voltage and High-voltage Operation
̶
̶
Grade 1, VCC = 2.5V to 5.5V
Grade 2(1) and 3, VCC = 1.7V to 5.5V
Extended Temperature Range (Grade 1, 2(1), and 3 as defined in AEC-Q100)
̶
̶
̶
Grade 1 Temperature Range: -40C to 125C
Grade 2 Temperature Range(1): -40C to 105C
Grade 3 Temperature Range: -40C to 85C
5MHz Clock Rate
8-byte Page Mode
Block Write Protection
̶
Protect 1/4, 1/2, or entire array
Write Protect (WP) Pin and Write Disable Instructions for Both Hardware and
Software Data Protection
Self-timed Write Cycle (5ms max)
High Reliability
̶
̶
Endurance: 1,000,000 Write cycles
Data Retention: 100 years
8-lead JEDEC SOIC, 8-lead TSSOP, and 8-pad UDFN Packages
Note: 1. Contact Sales for Grade 2 Availability
Description
The Atmel® AT25010B/020B/040B provides 1,024/2,048/4,096 bits of Serial
Electrically Erasable Programmable Read-Only Memory (EEPROM) organized as
128/256/512 words of 8 bits each. The device is optimized for use in many
automotive applications where low-power and low-voltage operation are essential.
AT25010B/020B/040B is available in space-saving 8-lead JEDEC SOIC, 8-lead
TSSOP, and 8-pad UDFN Packages.
AT25010B/020B/040B is enabled through the Chip Select pin (CS) and accessed
via a 3-wire interface consisting of Serial Data Input (SI), Serial Data Output (SO),
and Serial Clock (SCK). All programming cycles are completely self-timed, and no
separate erase cycle is required before Write.
Block Write Protection is enabled by programming the status register with one of
four blocks of Write Protection. Separate Program Enable and Program Disable
instructions are provided for additional data protection. Hardware data protection
is provided via the WP pin to protect against inadvertent write attempts. The
HOLD pin may be used to suspend any serial communication without resetting the
serial sequence.
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
Table of Contents
1. Pin Descriptions and Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Absolute Maximum Ratings* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Serial Interface Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5. Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5.1
5.2
5.3
Pin Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7. Timing Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7.1
Power Recommendation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.1
8.2
Ordering Code Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Ordering Code Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
8.2.1
8.2.2
Automotive Grade 1, VCC = 2.5V to 5.5V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Automotive Grade 3, VCC = 1.7V to 5.5V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8.3
Product Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
9. Packaging Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
9.1
9.2
9.3
8S1 — 8-lead JEDEC SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
8X — 8-lead TSSOP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8MA2 — 8-pad UDFN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
10. Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2
Atmel AT25010B/020B/040B Automotive [DATASHEET]
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
1.
Pin Descriptions and Pinouts
Figure 1.
Pin Configurations
8-lead SOIC
(Top View)
8-lead TSSOP
(Top View)
Pin Name
CS
Function
Chip Select
CS
SO
VCC
1
2
3
4
8
7
6
5
1
2
3
4
8
7
6
5
CS
SO
WP
VCC
HOLD
SCK
SI
HOLD
SCK
SI
SCK
SI
Serial Data Clock
Serial Data Input
Serial Data Output
Ground
WP
GND
GND
SO
8-pad UDFN
(Top View)
GND
VCC
CS
SO
WP
VCC
1
2
3
4
8
7
6
5
Power Supply
Write Protect
HOLD
SCK
SI
WP
GND
HOLD
Suspends Serial Input
Note:
Drawings are not to scale.
2.
Absolute Maximum Ratings*
*Notice: Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent
damage to the device. This is a stress rating
only and functional operation of the device at
these or any other conditions beyond those
indicated in the operational sections of this
specification is not implied. Exposure to
Operating Temperature . . . . . . . . . . .-40C to +125C
Storage Temperature . . . . . . . . . . . . .-65C to +150C
Voltage on any pin
with respect to ground . . . . . . . . . . . . . -1.0V to +7.0V
Maximum Operating Voltage . . . . . . . . . . . . . . . 6.25V
DC Output Current . . . . . . . . . . . . . . . . . . . . . . .5.0mA
absolute maximum rating conditions for
extended periods may affect device reliability.
Atmel AT25010B/020B/040B Automotive [DATASHEET]
3
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
3.
Block Diagram
Figure 3-1.
Block Diagram
VCC
GND
Status
Register
Memory Array
128/256/512 X 8
Address
Decoder
Data
Register
Output
Buffer
SI
Mode
Decode
Logic
CS
WP
Clock
Generator
SO
SCK
HOLD
4
Atmel AT25010B/020B/040B Automotive [DATASHEET]
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
4.
Serial Interface Description
Master: The device that generates the serial clock.
Slave: Because the Serial Clock pin (SCK) is always an input, AT25010B/020B/040B always operates as a
slave.
Transmitter/Receiver: AT25010B/020B/040B has separate pins designated for data transmission (SO) and
reception (SI).
MSB: The Most Significant Bit (MSB) is the first bit transmitted and received.
Serial Opcode: After the device is selected with CS going low, the first byte will be received. This byte contains
the opcode that defines the operations to be performed. The opcode also contains address bit A8 in both the
Read and the Write instructions for AT25040B only.
Invalid Opcode: If an invalid opcode is received, no data will be shifted into AT25010B/020B/040B, and the
Serial Output pin (SO) will remain in a high impedance state until the falling edge of CS is detected again. This
will reinitialize the serial communication.
Chip Select: AT25010B/020B/040B is selected when the CS pin is low. When the device is not selected, data
will not be accepted via the SI pin, and the Serial Output pin (SO) will remain in a high impedance state.
Hold: The HOLD pin is used in conjunction with the CS pin to select AT25010B/020B/040B. When the device is
selected and a serial sequence is underway, Hold can be used to pause the serial communication with the
master device without resetting the serial sequence. To pause, the HOLD pin must be brought low while the
SCK pin is low. To resume serial communication, the HOLD pin is brought high while the SCK pin is low (SCK
may still toggle during Hold). Inputs to the SI pin will be ignored while the SO pin is in the high impedance state.
Write Protect: The Write Protect pin (WP) will allow normal read/write operations when held high. When the
WP pin is brought low, all write operations are inhibited. WP going low while CS is still low will interrupt a write to
AT25010B/020B/040B. If the internal write cycle has already been initiated, WP going low will have no effect on
any write operation.
Atmel AT25010B/020B/040B Automotive [DATASHEET]
5
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
Figure 4-1.
SPI Serial Interface
Master:
Slave:
AT25010B/020B/040B
Microcontroller
Data Out (MOSI)
Data In (MISO)
Serial Clock (SPI CK)
SS0
SI
SO
SCK
CS
SS1
SI
SS2
SO
SCK
CS
SS3
SI
SO
SCK
CS
SI
SO
SCK
CS
6
Atmel AT25010B/020B/040B Automotive [DATASHEET]
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
5.
Electrical Characteristics
5.1
Pin Capacitance
Table 5-1.
Pin Capacitance(1)
Applicable at these conditions, unless otherwise noted. TA = 25C, f = 1.0MHz, VCC = +5.0V.
Symbol
COUT
CIN
Test Conditions
Max
8
Units
pF
Conditions
VOUT = 0V
VIN = 0V
Output Capacitance (SO)
Input Capacitance (CS, SCK, SI, WP, HOLD)
6
pF
Note:
1. This parameter is characterized and is not 100% tested.
5.2
DC Characteristics
Table 5-2.
DC Characteristics
Applicable over recommended operating range from: TA1 = -40C to +125C, VCC1 = 2.5V to 5.5V;
TA2 = -40C to 105C, VCC2 = 1.7V to 5.5V.
Symbol Parameter
Test Condition
Min
2.5
1.7
Typ
Max
Units
VCC1
Grade 1
5.5
5.5
6.0
3.0
6.0
2.0
3.0
5.0
Supply Voltage
V
VCC2
ICC1
ICC2
ICC3
ISB1
ISB2
ISB3
IIL
Grade 2(2) and 3
VCC = 5.0V at 5MHz, SO = Open, Read
VCC = 5.0V at 1MHz
VCC = 5.0V at 5MHz, SO = Open, Read, Write
VCC = 1.7V, CS = VCC
VCC = 2.5V, CS = VCC
VCC = 5.0V, CS = VCC
VIN = 0V to VCC
Supply Current
Standby Current
mA
0.1
0.2
2.0
μA
Input Leakage
-3.0
-3.0
μA
V
IOL
Output Leakage
VIN = 0V to VCC
3.0
(1)
VIL
Input Low-voltage
Input High-voltage
Output Low-voltage
Output High-voltage
Output Low-voltage
Output High-voltage
-0.6
VCC x 0.3
VCC + 0.5
0.4
(1)
VIH
VCC x 0.7
VOL1
VOH1
VOL2
VOH2
IOL = 3.0mA
2.5V VCC 5.5V
V
IOH = 1.6mA
VCC 0.8
VCC 0.2
IOL = 0.15mA
1.7V VCC 5.5V
0.2
V
IOH = -100μA
Notes: 1. VIL min and VIH max are reference only and are not tested.
2. Contact Sales for Grade 2 Availability
Atmel AT25010B/020B/040B Automotive [DATASHEET]
7
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
5.3
AC Characteristics
Table 5-3.
AC Characteristics
Applicable over recommended operating range from TA = -40C to +125C, VCC = As Specified, CL = 1 TTL Gate and 100pF
(unless otherwise noted).
Symbol
Parameter
Voltage
1.7 to 5.5
1.7 to 5.5
1.7 to 5.5
1.7 to 5.5
1.7 to 5.5
1.7 to 5.5
1.7 to 5.5
1.7 to 5.5
1.7 to 5.5
1.7 to 5.5
1.7 to 5.5
1.7 to 5.5
1.7 to 5.5
1.7 to 5.5
1.7 to 5.5
1.7 to 5.5
1.7 to 5.5
1.7 to 5.5
Min
Max
5.0
2
Units
fSCK
SCK Clock Frequency
Input Rise Time
Input Fall Time
0
MHz
tRI
μs
tFI
2
μs
tWH
SCK High Time
SCK Low Time
40
40
80
80
80
5
ns
tWL
ns
tCS
CS High Time
ns
tCSS
CS Setup Time
ns
tCSH
CS Hold Time
ns
tSU
Data In Setup Time
Data In Hold Time
Hold Setup Time
Hold Time
ns
tH
20
40
40
0
ns
tHD
ns
tCD
ns
tV
Output Valid
40
ns
tHO
Output Hold Time
Hold to Output Low Z
Hold to Output High Z
Output Disable Time
Write Cycle Time
5.0V, 25°C, Page Mode
0
ns
tLZ
0
40
80
80
5
ns
tHZ
ns
ns
tDIS
tWC
ms
Endurance(1)
1,000,000
Write Cycles
Note:
1. This parameter is characterized and is not 100% tested.
8
Atmel AT25010B/020B/040B Automotive [DATASHEET]
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
6.
Functional Description
AT25010B/020B/040B is designed to interface directly with the synchronous Serial Peripheral Interface (SPI) of
the 6805 and 68HC11 series of microcontrollers.
AT25010B/020B/040B utilizes an 8-bit instruction register. The list of instructions and their operation codes are
contained in Table 6-1. All instructions, addresses, and data are transferred with the MSB first and start with a
high-to-low CS transition.
Table 6-1.
Instruction Set for the Atmel AT25010B/020B/040B
Instruction Name
WREN
Instruction Format
0000 X110
Operation
Set Write Enable Latch
Reset Write Enable Latch
Read Status Register
Write Status Register
Read Data from Memory Array
Write Data to Memory Array
WRDI
0000 X100
RDSR
0000 X101
WRSR
0000 X001
READ
0000 A011
WRITE
0000 A010
Note:
“A” represents the ninth address bit (MSB bit A8) needed for AT25040B only.
Write Enable (WREN): The device will power up in the Write Disable state when VCC is applied. All
programming instructions must therefore be preceded by a Write Enable instruction.
Write Disable (WRDI): To protect the device against inadvertent writes, the Write Disable instruction disables
all programming modes. The WRDI instruction is independent of the status of the WP pin.
Read Status Register (RDSR): The Read Status Register instruction provides access to the status register.
The Ready/Busy and Write Enable status of the device can be determined by the RDSR instruction. Similarly,
the Block Write protection bits indicate the extent of protection employed. These bits are set by using the WRSR
instruction.
Table 6-2.
Bit 7
Status Register Format
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
X
X
X
X
BP1
BP0
WEN
RDY
Table 6-3.
Bit
Read Status Register Bit Definition
Definition
Bit 0 = 0 (RDY) indicates the device is ready.
Bit 0 = 1 indicates the write cycle is in progress.
Bit 0 (RDY)
Bit 1 (WEN)
Bit 1 = 0 indicates the device is not write-enabled.
Bit 1 = 1 indicates the device is write-enabled.
Bit 2 (BP0)
Bit 3 (BP1)
See Table 6-4 on page 10.
See Table 6-4 on page 10.
Bits 4 7 = 0 when the device is not in an internal write cycle.
Bits 4 7 = 1 during an internal write cycle.
Bits 4 -7
Write Status Register (WRSR): The WRSR instruction allows the user to select one of four levels of protection.
AT25010B/020B/040B is divided into four array segments. One-quarter, one-half, or all of the memory
segments can be protected. Any of the data within any selected segment will therefore be read-only. The Block
Write protection levels and corresponding status register control bits are shown in Table 6-4.
Atmel AT25010B/020B/040B Automotive [DATASHEET]
9
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
Bits BP0 and BP1 are nonvolatile cells that have the same properties and functions as the regular memory cells
(e.g., WREN, tWC, RDSR).
Table 6-4.
Block Write Protect Bits
Status
Register Bits
Array Addresses Protected
Level
0
BP1
BP0
AT25010B
None
AT25020B
None
AT25040B
None
0
0
1
1
0
1
0
1
1 (1/4)
2 (1/2)
3 (All)
60 - 7F
40 - 7F
00 - 7F
C0 - FF
80 - FF
00 - FF
180 - 1FF
100 - 1FF
000 - 1FF
Read Sequence (Read): Reading AT25010B/020B/040B via the Serial Output (SO) pin requires the following
sequence. After the CS line is pulled low to select a device, the Read opcode is transmitted via the SI line
followed by the byte address to be read (A7–A0, see Table 6-5). Upon completion, any data on the SI line will be
ignored. The data (D7–D0) at the specified address is then shifted out onto the SO line. If only one byte is to be
read, the CS line should be driven high after the data comes out. The Read sequence can be continued since
the byte address is automatically incremented and data will continue to be shifted out. When the highest
address is reached, the address counter will roll over to the lowest address, allowing the entire memory to be
read in one continuous Read cycle.
Write Sequence (Write): In order to program AT25010B/020B/040B, two separate instructions must be
executed. First, the device must be Write Enabled via the WREN instruction. Then a Write instruction may be
executed. Also, the address of the memory location(s) to be programmed must be outside the protected
address field location selected by the Block Write protection level. During an internal write cycle, all commands
will be ignored except the RDSR instruction.
A Write instruction requires the following sequence. After the CS line is pulled low to select the device, the Write
opcode is transmitted via the SI line followed by the byte address (A7A0) and the data (D7–D0) to be
programmed (See Table 6-5). Programming will start after the CS pin is brought high. The low-to-high transition
of the CS pin must occur during the SCK low-time immediately after clocking in the D0 (LSB) data bit.
The Ready/Busy status of the device can be determined by initiating a Read status register (RDSR) instruction.
If Bit 0 = one, the Write cycle is still in progress. If Bit 0 = zero, the Write cycle has ended. Only the RDSR
instruction is enabled during the Write programming cycle.
AT25010B/020B/040B is capable of a 8-byte Page Write operation. After each byte of data is received, the three
low-order address bits are internally incremented by one; the high-order bits of the address will remain constant.
If more than eight bytes of data are transmitted, the address counter will roll over and the previously written data
will be overwritten. AT25010B/020B/040B is automatically returned to the Write Disable state at the completion
of a Write cycle.
Note: If the device is not Write Enabled (WREN), the device will ignore the Write instruction and will return to
the standby state, when CS is brought high. A new CS falling edge is required to reinitiate the serial
communication.
Table 6-5.
Address
AN
Don’t Care Bits
Address Key
AT25010B
A6–A0
A7
AT25020B
A7–A0
AT25040B
A8–A0
None
None
Note:
The A8 bit (AT25040B address MSB) must appear embedded in the opcode as illustrated in Table 6-1.
10
Atmel AT25010B/020B/040B Automotive [DATASHEET]
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
7.
Timing Diagrams
Figure 7-1.
Synchronous Data Timing (for Mode 0)
tCS
VIH
CS
VIL
tCSH
tCSS
VIH
SCK
tWH
tWL
VIL
tSU
tH
VIH
SI
VALID IN
VIL
tHO
tDIS
tV
VOH
HI-Z
HI-Z
SO
VOL
Figure 7-2.
WREN Timing
CS
SCK
SI
WREN Opcode
HI-Z
SO
Figure 7-3.
WRDI Timing
CS
SCK
SI
WRDI Opcode
HI-Z
SO
Atmel AT25010B/020B/040B Automotive [DATASHEET]
11
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
Figure 7-4.
RDSR Timing
CS
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SCK
SI
Instruction
Data Out
4
High-impedance
7
MSB
6
3
2
1
0
SO
5
Figure 7-5.
WRSR Timing
CS
0
1
2
3
4
5
6
7
8
9
10
5
11
4
12
13
2
14
1
15
0
SCK
SI
Data In
3
Instruction
7
6
High-impedance
SO
12
Atmel AT25010B/020B/040B Automotive [DATASHEET]
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
Figure 7-6.
Read Timing
CS
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
SCK
SI
Instruction
Byte Address
8
7
6
5
4
3
2
1
0
9th Bit of Address
Data Out
High Impedance
SO
7
6
5
4
3
2
1
0
MSB
Figure 7-7.
Write Timing
CS
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
SCK
SI
Instruction
Byte Address
Data In
8
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
9th Bit of Address
High Impedance
SO
Atmel AT25010B/020B/040B Automotive [DATASHEET]
13
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
Figure 7-8.
HOLD Timing
CS
SCK
HOLD
SO
7.1
Power Recommendation
The device internal POR (Power-On Reset) threshold is just below the minimum device operating voltage.
Power shall rise monotonically from 0.0Vdc to full VCC in less than 1ms. Hold at full VCC for at least 100μs before
the first operation. Power shall drop from full VCC to 0.0Vdc in less than 1ms. Power dropping to a non-zero level
and then slowly going to zero is not recommended. Power shall remain off (0.0Vdc) for 0.5s minimum. Please
consult Atmel if your power conditions do not meet the above recommendations.
14
Atmel AT25010B/020B/040B Automotive [DATASHEET]
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
8.
Ordering Information
8.1
Ordering Code Detail
A T 2 5 0 1 0 B - S S P D - T
Atmel Designator
Shipping Carrier Option
T = Tape and Reel, Standard Quantity Option
E = Tape and Reel, Expanded Quantity Option
Product Family
25 = SPI
Serial EEPROM
Operating Voltage
M = 1.7V to 5.5V
D = 2.5V to 5.5V
Device Density
Package Device Grade or
Wafer/Die Thickness
010 = 1 kilobit
020 = 2 kilobit
040 = 4 kilobit
9
= Lead-free / Halogen-free
Automotive Grade 3 (-40°C to +85°C)
(1)
K = Lead-free / Halogen-free
Automotive Grade 2 (-40°C to +105°C)
P = Lead-free / Halogen-free
Automotive Grade 1(-40°C to +125°C)
Device Revision
Package Option
SS = JEDEC SOIC
X
= TSSOP
MA= UDFN
Note:
1. Contact Sales for Grade 2 Availability
Atmel AT25010B/020B/040B Automotive [DATASHEET]
15
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
8.2
Ordering Code Information
8.2.1 Automotive Grade 1, VCC = 2.5V to 5.5V
Delivery Information
Atmel Ordering Code
AT25010B-SSPD-T
AT25010B-XPD-T
Lead Finish
Package
8S1
Form
Quantity
Operation Range
4,000 per Reel
5,000 per Reel
5,000 per Reel
15,000 per Reel
Automotive
Temperature
(-40C to 125C)
8X
NiPdAu
(Lead-free/Halogen-free)
Tape and Reel
AT25010B-MAPD-T
AT25010B-MAPD-E
8MA2
AT25020B-SSPD-T
AT25020B-XPD-T
AT25020B-MAPD-T
8S1
8X
4,000 per Reel
5,000 per Reel
5,000 per Reel
15,000 per Reel
Automotive
Temperature
(-40C to 125C)
NiPdAu
(Lead-free/Halogen-free)
Tape and Reel
8MA2
AT25020B-MAPD-E
1
AT25040B-SSPD-T
AT25040B-XPD-T
AT25040B-MAPD-T
AT25040B-MAPD-E
8S1
8X
4,000 per Reel
5,000 per Reel
5,000 per Reel
15,000 per Reel
Automotive
Temperature
(-40C to 125C)
NiPdAu
(Lead-free/Halogen-free)
Tape and Reel
8MA2
Package Type
8S1
8X
8-lead, 0.150" wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
8-lead 4.4mm body, Plastic Thin Shrink Small Outline (TSSOP)
8MA2
8-pad, 2.00mm x 3.00mm body, 0.50mm pitch, Ultra Thin, Dual No Lead (UDFN)
16
Atmel AT25010B/020B/040B Automotive [DATASHEET]
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
8.2.2 Automotive Grade 3, VCC = 1.7V to 5.5V
Delivery Information
Atmel Ordering Code
AT25010B-SS9M-T
AT25010B-X9M-T
Lead Finish
Package
8S1
Form
Quantity
Operation Range
4,000 per Reel
5,000 per Reel
5,000 per Reel
15,000 per Reel
Automotive
Temperature
(-40C to 85C)
8X
NiPdAu
(Lead-free/Halogen-free)
Tape and Reel
AT25010B-MA9M-T
AT25010B-MA9M-E
8MA2
AT25020B-SS9M-T
AT25020B-X9M-T
AT25020B-MA9M-T
AT25020B-MA9M-E
8S1
8X
4,000 per Reel
5,000 per Reel
5,000 per Reel
15,000 per Reel
Automotive
Temperature
(-40C to 85C)
NiPdAu
(Lead-free/Halogen-free)
Tape and Reel
8MA2
AT25040B-SS9M-T
AT25040B-X9M-T
AT25040B-MA9M-T
AT25040B-MA9M-E
8S1
8X
4,000 per Reel
5,000 per Reel
5,000 per Reel
15,000 per Reel
Automotive
Temperature
(-40C to 85C)
NiPdAu
(Lead-free/Halogen-free)
Tape and Reel
8MA2
Package Type
8S1
8X
8-lead, 0.150" wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
8-lead 4.4mm body, Plastic Thin Shrink Small Outline (TSSOP)
8MA2
8-pad, 2.00mm x 3.00mm body, 0.50mm pitch, Ultra Thin, Dual No Lead (UDFN)
Atmel AT25010B/020B/040B Automotive [DATASHEET]
17
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
8.3
Product Markings
AT25010B, AT25020B, and AT25040B: Package Marking Information
8-lead SOIC
8-lead TSSOP
8-pad UDFN
2.0 x 3.0 mm Body
###
AT$YWW
AAAAAAA
ATML$YWW
###%
AAAAAAAA
$%@
YTC
###% @
@
Note 1: designates pin 1
Note 2: Package drawings are not to scale
Catalog Number Truncation
AT25010B
AT25020B
Truncation Code ###: 51B
Truncation Code ###: 52B
Truncation Code ###: 54B
AT25040B
Date Codes
% = Voltages
Y = Year
6: 2016
7: 2017
8: 2018
9: 2019
M = Month
A: January
B: February
...
WW = Work Week of Assembly
M: 1.7V min
D: 2.5V min
0: 2020
1: 2021
2: 2022
3: 2023
02: Week 2
04: Week 4
...
L: December
52: Week 52
Country of Assembly
Lot Number
AAA...A = Atmel Wafer Lot Number
$ = Grade/Lead Finish Material
@ = Country of Assembly
P: Automotive Grade 1/NiPdAu
K: Automotive Grade 2/NiPdAu
9: Automotive Grade 3/NiPdAu
Trace Code
Atmel Truncation
XX = Trace Code (Atmel Lot Numbers Correspond to Code)
Example: AA, AB.... YZ, ZZ
AT: Atmel
ATM: Atmel
ATML: Atmel
4/20/2016
REV.
TITLE
DRAWING NO.
25010-20-40BAM, AT25010B, AT25020B and AT25040B
Automotive Package Marking Information
Package Mark Contact:
DL-CSO-Assy_eng@atmel.com
25010-20-40BAM
E
18
Atmel AT25010B/020B/040B Automotive [DATASHEET]
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
9.
Packaging Information
9.1
8S1 — 8-lead JEDEC SOIC
C
1
E
E1
L
N
Ø
TOP VIEW
END VIEW
e
b
COMMON DIMENSIONS
(Unit of Measure = mm)
A
MIN
–
0.10
MAX
1.75
0.25
NOM
–
–
NOTE
SYMBOL
A1
A
A1
b
0.31
0.17
–
0.51
0.25
C
D
E
E1
e
–
4.90 BSC
6.00 BSC
3.90 BSC
1.27 BSC
–
D
SIDE VIEW
Notes: This drawing is for general information only.
Refer to JEDEC Drawing MS-012, Variation AA
for proper dimensions, tolerances, datums, etc.
L
0.40
0°
1.27
8°
Ø
–
3/6/2015
DRAWING NO. REV.
8S1
TITLE
GPC
8S1, 8-lead (0.150” Wide Body), Plastic Gull Wing
Small Outline (JEDEC SOIC)
SWB
H
Package Drawing Contact:
packagedrawings@atmel.com
Atmel AT25010B/020B/040B Automotive [DATASHEET]
19
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
9.2
8X — 8-lead TSSOP
C
1
Pin 1 indicator
this corner
E1
E
L1
N
L
Top View
End View
A
b
A1
COMMON DIMENSIONS
(Unit of Measure = mm)
e
A2
D
SYMBOL
MIN
-
NOM
-
MAX
1.20
0.15
1.05
3.10
NOTE
2, 5
A
Side View
A1
A2
D
0.05
0.80
2.90
-
Notes: 1. This drawing is for general information only.
1.00
Refer to JEDEC Drawing MO-153, Variation AA, for proper
dimensions, tolerances, datums, etc.
3.00
2. Dimension D does not include mold Flash, protrusions or gate
burrs. Mold Flash, protrusions and gate burrs shall not exceed
0.15mm (0.006in) per side.
E
6.40 BSC
4.40
E1
b
4.30
0.19
4.50
0.30
3, 5
4
3. Dimension E1 does not include inter-lead Flash or protrusions.
Inter-lead Flash and protrusions shall not exceed 0.25mm
(0.010in) per side.
4. Dimension b does not include Dambar protrusion.
Allowable Dambar protrusion shall be 0.08mm total in excess
of the b dimension at maximum material condition. Dambar
cannot be located on the lower radius of the foot. Minimum
space between protrusion and adjacent lead is 0.07mm.
5. Dimension D and E1 to be determined at Datum Plane H.
0.25
e
0.65 BSC
0.60
L
0.45
0.09
0.75
0.20
L1
C
1.00 REF
-
2/27/14
TITLE
GPC
TNR
DRAWING NO.
REV.
8X, 8-lead 4.4mm Body, Plastic Thin
Shrink Small Outline Package (TSSOP)
8X
E
Package Drawing Contact:
packagedrawings@atmel.com
20
Atmel AT25010B/020B/040B Automotive [DATASHEET]
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
9.3
8MA2 — 8-pad UDFN
E
1
8
7
6
5
Pin 1 ID
2
3
4
D
C
TOP VIEW
E2
SIDE VIEW
A2
A
C
A1
b (8x)
8
1
2
3
4
COMMON DIMENSIONS
(Unit of Measure = mm)
7
6
5
Pin#1 ID
D2
MIN
0.50
MAX
0.60
NOM
0.55
NOTE
SYMBOL
A
A1
A2
D
0.0
-
0.02
-
0.05
0.55
2.10
1.60
3.10
1.40
0.30
e (6x)
L (8x)
BOTTOM VIEW
K
1.90
1.40
2.90
1.20
0.18
2.00
D2
E
1.50
3.00
Notes:
1. This drawing is for general information only. Refer to
Drawing MO-229, for proper dimensions, tolerances,
datums, etc.
E2
b
1.30
0.25
3
2. The Pin #1 ID is a laser-marked feature on Top View.
3. Dimensions b applies to metallized terminal and is
measured between 0.15 mm and 0.30 mm from the
terminal tip. If the terminal has the optional radius on
the other end of the terminal, the dimension should
not be measured in that radius area.
C
0.152 REF
0.40
L
0.35
0.20
0.45
-
e
0.50 BSC
-
K
4. The Pin #1 ID on the Bottom View is an orientation
feature on the thermal pad.
11/2/15
TITLE
DRAWING NO.
REV.
GPC
8MA2, 8-pad 2 x 3 x 0.6mm Body, Thermally
Enhanced Plastic Ultra Thin Dual Flat No-Lead
Package (UDFN)
YNZ
8MA2
H
Package Drawing Contact:
packagedrawings@atmel.com
Atmel AT25010B/020B/040B Automotive [DATASHEET]
21
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
10. Revision History
Doc. Rev.
Date
Comments
8802E
12/2016
Decreased ISB1 maximum from 9μA to 2μA
Added the Automotive Grade 2 and 3 options and UDFN options.
8802D
8802C
09/2016
11/2012
Updated 8S1 and 8X package drawings, template / reorganization, and disclaimer page.
Updated ordering code tables.
Updated 8X package drawing.
Removed preliminary status.
8802B
8802A
10/2012
03/2012
Updated Atmel logos and disclaimer/copy page.
Initial document release.
22
Atmel AT25010B/020B/040B Automotive [DATASHEET]
Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016
X X
X X X X
Atmel Corporation
1600 Technology Drive, San Jose, CA 95110 USA
T: (+1)(408) 441.0311
F: (+1)(408) 436.4200
|
www.atmel.com
© 2016 Atmel Corporation. / Rev.: Atmel-8802E-SEEPROM-AT25010B-020B-040B-Auto-Datasheet_122016.
Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, and others are registered trademarks or trademarks of Atmel Corporation in U.S. and
other countries. Other terms and product names may be trademarks of others.
DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right
is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE
ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT
SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this
document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information
contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended,
authorized, or warranted for use as components in applications intended to support or sustain life.
SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where
the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without an Atmel officer's specific written
consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems.
Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are
not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.
相关型号：
©2020 ICPDF网 联系我们和版权申明