AT24CM-SSHD-T [MICROCHIP]
I²C-Compatible (Two-Wire) Serial EEPROM 2âMbit (262,144 x 8);型号: | AT24CM-SSHD-T |
厂家: | MICROCHIP |
描述: | I²C-Compatible (Two-Wire) Serial EEPROM 2âMbit (262,144 x 8) 可编程只读存储器 电动程控只读存储器 电可擦编程只读存储器 |
文件: | 总34页 (文件大小:1325K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
AT24CM02
I²C-Compatible (Two-Wire)
Serial EEPROM 2‑Mbit (262,144 x 8)
Features
•
Low-Voltage and Standard-Voltage Operation:
– VCC = 1.7V to 5.5V
– VCC = 2.5V to 5.5V
•
•
•
Internally Organized as 262,144 x 8 (2‑Mbit)
Industrial Temperature Range: -40°C to +85°C
I2C-Compatible (Two-Wire) Serial Interface:
– 100 kHz Standard Mode, 1.7V to 5.5V
– 400 kHz Fast Mode, 1.7V to 5.5V
– 1 MHz Fast Mode Plus (FM+), 2.5V to 5.5V
Schmitt Triggers, Filtered Inputs for Noise Suppression
Bidirectional Data Transfer Protocol
•
•
•
•
•
Write-Protect Pin for Full Array Hardware Data Protection
Ultra Low Active Current (3 mA maximum) and Standby Current (3 µA maximum)
256-byte Page Write Mode:
– Byte write and partial page writes allowed
Random and Sequential Read Modes
•
•
Self-Timed Write Cycle:
– All write operations complete within 10 ms maximum
Built-in Error Detection and Correction
•
•
High Reliability:
– Endurance: 1,000,000 write cycles
– Data retention: 100 years
•
•
Green Package Options (Lead-free/Halide-free/RoHS compliant)
Die Sale Options: Wafer Form and Bumped Wafers
Packages
•
8-Lead SOIC and 8-Ball WLCSP
DS20006197C-page 1
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Table of Contents
Features......................................................................................................................................................... 1
Packages........................................................................................................................................................1
1. Package Types (not to scale)..................................................................................................................4
2. Pin Descriptions...................................................................................................................................... 5
2.1. Device Address Input (A2)........................................................................................................... 5
2.2. Ground......................................................................................................................................... 5
2.3. Serial Data (SDA).........................................................................................................................5
2.4. Serial Clock (SCL)........................................................................................................................5
2.5. Write-Protect (WP)....................................................................................................................... 6
2.6. Device Power Supply................................................................................................................... 6
3. Description.............................................................................................................................................. 7
3.1. System Configuration Using Two-Wire Serial EEPROMs ...........................................................7
3.2. Block Diagram..............................................................................................................................8
4. Electrical Characteristics.........................................................................................................................9
4.1. Absolute Maximum Ratings..........................................................................................................9
4.2. DC and AC Operating Range.......................................................................................................9
4.3. DC Characteristics....................................................................................................................... 9
4.4. AC Characteristics......................................................................................................................10
4.5. Electrical Specifications..............................................................................................................11
5. Device Operation and Communication................................................................................................. 13
5.1. Clock and Data Transition Requirements...................................................................................13
5.2. Start and Stop Conditions.......................................................................................................... 13
5.3. Acknowledge and No-Acknowledge...........................................................................................14
5.4. Standby Mode............................................................................................................................ 14
5.5. Software Reset...........................................................................................................................14
6. Memory Organization............................................................................................................................16
6.1. Device Addressing..................................................................................................................... 16
7. Write Operations................................................................................................................................... 17
7.1. Byte Write...................................................................................................................................17
7.2. Page Write..................................................................................................................................17
7.3. Internal Writing Methodology......................................................................................................18
7.4. Acknowledge Polling.................................................................................................................. 18
7.5. Write Cycle Timing..................................................................................................................... 19
7.6. Write Protection..........................................................................................................................19
8. Read Operations...................................................................................................................................21
8.1. Current Address Read................................................................................................................21
8.2. Random Read............................................................................................................................ 21
8.3. Sequential Read.........................................................................................................................22
DS20006197C-page 2
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
9. Device Default Condition from Microchip..............................................................................................23
10. Packaging Information.......................................................................................................................... 24
10.1. Package Marking Information.....................................................................................................24
11. Revision History.................................................................................................................................... 29
The Microchip Website.................................................................................................................................30
Product Change Notification Service............................................................................................................30
Customer Support........................................................................................................................................ 30
Product Identification System.......................................................................................................................31
Microchip Devices Code Protection Feature................................................................................................31
Legal Notice................................................................................................................................................. 32
Trademarks.................................................................................................................................................. 32
Quality Management System....................................................................................................................... 33
Worldwide Sales and Service.......................................................................................................................34
DS20006197C-page 3
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Package Types (not to scale)
1.
Package Types (not to scale)
8-Lead SOIC
8-Ball WLCSP
(Top View)
(Top View)
NC
1
2
8
7
VCC
VCC
WP
A2
B2
A3
NC
B4 NC
NC
A2
WP
3
4
6
5
SCL
SDA
SCL
SDA
C1
C4
A2
D2
D3
GND
GND
DS20006197C-page 4
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Pin Descriptions
2.
Pin Descriptions
The descriptions of the pins are listed in Table 2-1.
Table 2-1.ꢀPin Function Table
Name
NC
8‑Lead SOIC
8‑Ball WLCSP
Function
1
2
3
4
5
6
7
8
A3
B4
C4
D3
D2
C1
B2
A2
No Connect
No Connect
NC
(1)
A2
Device Address Input
Ground
GND
SDA
SCL
Serial Data
Serial Clock
(1)
WP
Write-Protect
V
Device Power Supply
CC
Note:ꢀ
1. If the A2 or WP pins are not driven, they are internally pulled down to GND. In order to operate in a wide
variety of application environments, the pull-down mechanism is intentionally designed to be somewhat strong.
Once these pins are biased above the CMOS input buffer’s trip point (~0.5 x VCC), the pull‑down mechanism
disengages. Microchip recommends connecting these pins to a known state whenever possible.
2.1
Device Address Input (A2)
The A2 pin is a device address input that is hard-wired (directly to GND or to VCC) for compatibility with other two-wire
Serial EEPROM devices. When the pin is hard-wired, as many as two devices may be addressed on a single bus
system. A device is selected when a corresponding hardware and software match is true. If the pin is left floating,
the A2 pin will be internally pulled down to GND. However, due to capacitive coupling that may appear in customer
applications, Microchip recommends always connecting the address pin to a known state. When using a pull-up
resistor, Microchip recommends using 10 kΩ or less.
2.2
2.3
Ground
The ground reference for the power supply. GND should be connected to the system ground.
Serial Data (SDA)
The SDA pin is an open-drain bidirectional input/output pin used to serially transfer data to and from the device. The
SDA pin must be pulled high using an external pull-up resistor (not to exceed 10 kΩ in value) and may be wire-ORed
with any number of other open-drain or open-collector pins from other devices on the same bus.
2.4
Serial Clock (SCL)
The SCL pin is used to provide a clock to the device and to control the flow of data to and from the device. Command
and input data present on the SDA pin is always latched in on the rising edge of SCL, while output data on the SDA
pin is clocked out on the falling edge of SCL. The SCL pin must either be forced high when the serial bus is idle or
pulled high using an external pull-up resistor.
DS20006197C-page 5
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Pin Descriptions
2.5
Write-Protect (WP)
The write-protect input, when connected to GND, allows normal write operations. When the WP pin is connected
directly to VCC, all write operations to the protected memory are inhibited.
If the pin is left floating, the WP pin will be internally pulled down to GND. However, due to capacitive coupling that
may appear in customer applications, Microchip recommends always connecting the WP pin to a known state. When
using a pull‑up resistor, Microchip recommends using 10 kΩ or less.
Table 2-2.ꢀWrite-Protect
WP Pin Status
At VCC
Part of the Array Protected
Full Array
At GND
Normal Write Operations
2.6
Device Power Supply
The VCC pin is used to supply the source voltage to the device. Operations at invalid VCC voltages may produce
spurious results and should not be attempted.
DS20006197C-page 6
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Description
3.
Description
The AT24CM02 provides 2,097,152 bits of Serial Electrically Erasable and Programmable Read-Only Memory
(EEPROM) organized as 262,144 words of 8 bits each. The device's cascading feature allows up to four devices
to share a common two-wire bus. This device is optimized for use in many industrial and commercial applications
where low-power and low-voltage operations are essential. The device is available in space-saving 8-lead SOIC and
8-ball WLCSP packages. All packages operate from 1.7V to 5.5V.
3.1
System Configuration Using Two-Wire Serial EEPROMs
VCC
t
R(max)
R
R
PUP(max) =
PUP(min) =
0.8473 x C
L
V
- V
OL(max)
CC
V
CC
I
OL
SCL
SDA
WP
2
I C Bus Host:
Microcontroller
NC
NC
A2
VCC
WP
NC
NC
A2
VCC
WP
Client 0
AT24CXXX
Client 1
AT24CXXX
SDA
SCL
SDA
SCL
GND
GND
GND
DS20006197C-page 7
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Description
3.2
Block Diagram
Hardware
Address
Comparator
Power-on
Reset
Generator
Memory
System Control
Module
VCC
High Voltage
Generation Circuit
Write
Protection
Control
WP
EEPROM Array
Address Register
and Counter
1 page
Column Decoder
Data Register
A2
SCL
SDA
Start
Stop
Detector
Data & ACK
Input/Output Control
DOUT
DIN
GND
DS20006197C-page 8
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Electrical Characteristics
4.
Electrical Characteristics
4.1
Absolute Maximum Ratings
Temperature under bias
Storage temperature
VCC
-55°C to +125°C
-65°C to +150°C
6.25V
Voltage on any pin with respect to ground
DC output current
-1.0V to +7.0V
5.0 mA
ESD protection
>3 kV
Note:ꢀ Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at these or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
4.2
DC and AC Operating Range
Table 4-1.ꢀDC and AC Operating Range
AT24CM02
Operating Temperature (Case)
Industrial Temperature Range
Low-Voltage Grade
-40°C to +85°C
1.7V to 5.5V
2.5V to 5.5V
VCC Power Supply
Standard-Voltage Grade
4.3
DC Characteristics
Table 4-2.ꢀDC Characteristics
Parameter
Symbol
Minimum
Typical(1)
Maximum
Units
Test Conditions
Supply Voltage,
1.7V Option
VCC1
1.7
—
5.5
V
Supply Voltage,
2.5V Option
VCC2
2.5
—
—
5.5
0.5
V
0.1
mA
VCC = 1.8V(2)
,
Read at 400 kHz
Supply Current,
Read
ICC
VCC = 5.0V,
Read at 1 MHz
—
—
0.3
0.4
1.0
1.0
mA
mA
VCC = 1.8V(2)
,
averaged during tWR
Supply Current,
Write(3)
ICC
VCC = 5.0V,
averaged during tWR
—
1.7
3.0
mA
DS20006197C-page 9
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Electrical Characteristics
...........continued
Parameter
Symbol
Minimum
Typical(1)
Maximum
Units
Test Conditions
VCC = 1.8V(2)
VIN = VCC or VSS
,
—
0.08
1.0
μA
VCC = 2.5V,
VIN = VCC or VSS
Standby Current
ISB
—
0.08
2.0
μA
VCC = 5.5V,
VIN = VCC or VSS
—
—
—
0.15
0.10
0.05
3.0
3.0
3.0
μA
μA
μA
Input Leakage
Current
ILI
VIN = VCC or VSS
Output Leakage
Current
ILO
VOUT = VCC or VSS
Input Low Level
Input High Level
VIL
VIH
-0.6
—
—
VCC x 0.3
VCC + 0.5
V
V
Note 2
Note 2
VCC x 0.7
VCC = 1.7V,
IOL = 0.15 mA
Output Low Level
Output Low Level
Note:ꢀ
VOL1
VOL2
—
—
—
—
0.2
0.4
V
V
VCC = 3.0V, IOL = 2.1 mA
1. Typical values characterized at TA = +25°C unless otherwise noted.
2. This parameter is characterized but is not 100% tested in production.
3. Averaged during tWR
.
4.4
AC Characteristics
Table 4-3.ꢀAC Characteristics(1)
Standard Mode
Fast Mode
Fast Mode Plus
Parameter
Symbol VCC = 1.7V to 5.5V VCC = 1.7V to 5.5V VCC = 2.5V to 5.5V
Units
Min.
—
Max.
100
—
Min.
—
Max.
400
—
Min.
—
Max.
1000
—
Clock Frequency, SCL
Clock Pulse Width Low
Clock Pulse Width High
fSCL
tLOW
tHIGH
kHz
ns
4,700
4,000
1,300
600
500
400
—
—
—
ns
Input Filter Spike
tI
—
—
100
4,500
—
—
—
100
900
—
—
—
50
450
—
ns
ns
ns
Suppression (SCL,SDA)(2)
Clock Low to Data Out
Valid
tAA
tBUF
Bus Free Time between
Stop and Start(2)
4,700
1,300
500
Start Hold Time
tHD.STA
tSU.STA
tHD.DAT
tSU.DAT
tR
4,000
4,700
0
—
—
600
600
0
—
—
250
250
0
—
—
ns
ns
ns
ns
ns
ns
Start Set-up Time
Data In Hold Time
Data In Set-up Time
Inputs Rise Time(1)
Inputs Fall Time(1)
—
—
—
200
—
—
100
—
—
100
—
—
1,000
300
300
300
100
100
tF
—
—
—
Stop Condition Set-up
Time
tSU.STO
4,700
—
600
—
250
—
ns
DS20006197C-page 10
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Electrical Characteristics
...........continued
Parameter
Standard Mode
Fast Mode
Fast Mode Plus
Symbol VCC = 1.7V to 5.5V VCC = 1.7V to 5.5V VCC = 2.5V to 5.5V
Units
Min.
4,000
4,000
100
Max.
—
Min.
600
600
50
Max.
—
Min.
250
250
50
Max.
—
Write-Protect Setup Time
Write-Protect Hold Time
Data Out Hold Time
Write Cycle Time
tSU.WP
tHD.WP
tDH
ns
ns
ns
ms
—
—
—
—
—
—
tWR
—
10
—
10
—
10
Notes:ꢀ
1. AC measurement conditions:
– CL: 100 pF
– RPUP (SDA bus line pull-up resistor to VCC): 1.3 kΩ (1000 kHz), 4 kΩ (400 kHz), 10 kΩ (100 kHz)
– Input pulse voltages: 0.3 x VCC to 0.7 x VCC
– Input rise and fall times: ≤50 ns
– Input and output timing reference voltages: 0.5 x VCC
2. These parameters are determined through product characterization and are not 100% tested in production.
Figure 4-1.ꢀ Bus Timing
tHIGH
tF
tR
tLOW
SCL
tSU.STA
tHD.STA
tHD.DAT
tSU.DAT
tSU.STO
SDA In
tBUF
tAA
tDH
SDA Out
4.5
Electrical Specifications
4.5.1
Power-Up Requirements and Reset Behavior
During a power-up sequence, the VCC supplied to the AT24CM02 should monotonically rise from GND to the
minimum VCC level, as specified in Table 4-1, with a slew rate no faster than 0.1 V/µs.
4.5.1.1 Device Reset
To prevent inadvertent write operations or any other spurious events from occurring during a power-up sequence, the
AT24CM02 includes a Power-on Reset (POR) circuit. Upon power-up, the device will not respond to any commands
until the VCC level crosses the internal voltage threshold (VPOR) that brings the device out of Reset and into Standby
mode.
The system designer must ensure the instructions are not sent to the device until the VCC supply has reached a
stable value greater than or equal to the minimum VCC level. Additionally, once the VCC is greater than or equal to the
minimum VCC level, the bus host must wait at least tPUP before sending the first command to the device. See Table
4-4 for the values associated with these power-up parameters.
DS20006197C-page 11
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Electrical Characteristics
Table 4-4.ꢀPower-up Conditions(1)
Symbol
Parameter
Min. Max. Units
tPUP
VPOR
tPOFF
Time required after VCC is stable before the device can accept commands
Power-on Reset Threshold Voltage
100
-
1
-
1.5
-
µs
V
Minimum time at VCC = 0V between power cycles
ms
Note:ꢀ
1. These parameters are characterized but they are not 100% tested in production.
If an event occurs in the system where the VCC level supplied to the AT24CM02 drops below the maximum VPOR
level specified, it is recommended that a full power cycle sequence be performed. First, drive the VCC pin to GND,
waiting at least the minimum tPOFF time, and then perform a new power-up sequence in compliance with the
requirements defined in this section.
4.5.2
Pin Capacitance
Table 4-5.ꢀPin Capacitance(1)
Symbol
CI/O
Test Condition
Input/Output Capacitance (SDA)
Input Capacitance (A2 and SCL)
Max.
Units
pF
Conditions
VI/O = 0V
VIN = 0V
8
6
CIN
pF
Note:ꢀ
1. This parameter is characterized but is not 100% tested in production.
4.5.3
EEPROM Cell Performance Characteristics
Table 4-6.ꢀEEPROM Cell Performance Characteristics
Operation
Test Condition
Min.
Max.
Units
Write Endurance(1)
TA = 25°C, VCC(min.) < VCC < VCC(max.),
Byte(2) or Page Write mode
1,000,000
—
Write Cycles
Data Retention(1)
TA = 55°C
100
—
Years
Notes:ꢀ
1. Performance is determined through characterization and the qualification process.
2. Due to the memory array architecture, the Write Cycle Endurance is specified for writes in groups of four data
bytes. The beginning of any 4-byte boundaries can be determined by multiplying any integer (N) by four (i.e.,
4*N). The end address can be found by adding three to the beginning value (i.e., 4*N+3). See Internal Writing
Methodology for more details on this implementation.
DS20006197C-page 12
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Device Operation and Communication
5.
Device Operation and Communication
The AT24CM02 operates as a client device and utilizes a simple I2C-compatible two-wire digital serial interface to
communicate with a host controller, commonly referred to as the bus host. The host initiates and controls all read and
write operations to the client devices on the serial bus, and both the host and the client devices can transmit and
receive data on the bus.
The serial interface is comprised of just two signal lines: Serial Clock (SCL) and Serial Data (SDA). The SCL pin is
used to receive the clock signal from the host, while the bidirectional SDA pin is used to receive command and data
information from the host as well as to send data back to the host. Data is always latched into the AT24CM02 on
the rising edge of SCL and always output from the device on the falling edge of SCL. Both the SCL and SDA pins
incorporate integrated spike suppression filters and Schmitt Triggers to minimize the effects of input spikes and bus
noise.
All command and data information is transferred with the Most Significant bit (MSb) first. During bus communication,
one data bit is transmitted every clock cycle, and after eight bits (one byte) of data have been transferred, the
receiving device must respond with either an Acknowledge (ACK) or a No-Acknowledge (NACK) response bit during
a ninth clock cycle (ACK/NACK clock cycle) generated by the host. Therefore, nine clock cycles are required for
every one byte of data transferred. There are no unused clock cycles during any read or write operation, so there
must not be any interruptions or breaks in the data stream during each data byte transfer and ACK or NACK clock
cycle.
During data transfers, data on the SDA pin must only change while SCL is low and the data must remain stable while
SCL is high. If data on the SDA pin changes while SCL is high, then either a Start or a Stop condition will occur.
Start and Stop conditions are used to initiate and end all serial bus communication between the host and the client
devices. The number of data bytes transferred between a Start and a Stop condition is not limited and is determined
by the host. In order for the serial bus to be idle, both the SCL and SDA pins must be in the logic high state at the
same time.
5.1
Clock and Data Transition Requirements
The SDA pin is an open-drain terminal and therefore must be pulled high with an external pull‑up resistor. SCL is
an input pin that can either be driven high or pulled high using an external pull‑up resistor. Data on the SDA pin
may change only during SCL low time periods. Data changes during SCL high periods will indicate a Start or Stop
condition as defined below. The relationship of the AC timing parameters with respect to SCL and SDA for the
AT24CM02 are shown in the timing waveform in Figure 4-1. The AC timing characteristics and specifications are
outlined in AC Characteristics.
5.2
Start and Stop Conditions
5.2.1
Start Condition
A Start condition occurs when there is a high-to-low transition on the SDA pin while the SCL pin is at a stable logic
‘1’ state and will bring the device out of Standby mode. The host uses a Start condition to initiate any data transfer
sequence; therefore, every command must begin with a Start condition. The device will continuously monitor the SDA
and SCL pins for a Start condition but will not respond unless one is detected. Refer to Figure 5-1 for more details.
5.2.2
Stop Condition
A Stop condition occurs when there is a low-to-high transition on the SDA pin while the SCL pin is stable in the logic
‘1’ state.
The host can use the Stop condition to end a data transfer sequence with the AT24CM02, which will subsequently
return to Standby mode. The host can also utilize a repeated Start condition instead of a Stop condition to end the
current data transfer if the host will perform another operation. Refer to Figure 5-1 for more details.
DS20006197C-page 13
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Device Operation and Communication
5.3
Acknowledge and No-Acknowledge
After every byte of data is received, the receiving device must confirm to the transmitting device that it has
successfully received the data byte by responding with what is known as an Acknowledge (ACK). An ACK is
accomplished by the transmitting device first releasing the SDA line at the falling edge of the eighth clock cycle
followed by the receiving device responding with a logic ‘0’ during the entire high period of the ninth clock cycle.
When the AT24CM02 is transmitting data to the host, the host can indicate that it is done receiving data and wants
to end the operation by sending a logic ‘1’ response to the AT24CM02 instead of an ACK response during the ninth
clock cycle. This is known as a No-Acknowledge (NACK) and is accomplished by the host sending a logic ‘1’ during
the ninth clock cycle, at which point the AT24CM02 will release the SDA line so the host can then generate a Stop
condition.
The transmitting device, which can be the bus host or the Serial EEPROM, must release the SDA line at the
falling edge of the eighth clock cycle to allow the receiving device to drive the SDA line to a logic ‘0’ to ACK the
previous 8-bit word. The receiving device must release the SDA line at the end of the ninth clock cycle to allow the
transmitter to continue sending new data. A timing diagram has been provided in Figure 5-1 to better illustrate these
requirements.
Figure 5-1.ꢀStart Condition, Data Transitions, Stop Condition and Acknowledge
SDA
Must Be
Stable
SDA
Must Be
Stable
Acknowledge Window
1
2
8
9
SCL
SDA
Stop
Condition
Acknowledge
Valid
Start
Condition
The transmitting device (Host or Client)
The receiver (Host or Client)
SDA
Change
Allowed
SDA
Change
Allowed
must release the SDA line at this point to allow
the receiving device (Host or Client) to drive the
SDA line low to ACK the previous 8-bit word.
must release the SDA line at
this point to allow the transmitter
to continue sending new data.
5.4
5.5
Standby Mode
The AT24CM02 features a low-power Standby mode that is enabled when any one of the following occurs:
•
•
•
A valid power-up sequence is performed (see Power-Up Requirements and Reset Behavior).
A Stop condition is received by the device unless it initiates an internal write cycle (see Write Operations).
At the completion of an internal write cycle (see Write Operations).
Software Reset
After an interruption in protocol, power loss or system Reset, any two‑wire device can be protocol reset by clocking
SCL until SDA is released by the EEPROM and goes high. The number of clock cycles until SDA is released by the
EEPROM will vary. The software Reset sequence should not take more than nine dummy clock cycles. Once the
software Reset sequence is complete, new protocol can be sent to the device by sending a Start condition followed
by the protocol. Refer to Figure 5-2 for an illustration.
DS20006197C-page 14
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Device Operation and Communication
Figure 5-2.ꢀSoftware Reset
Dummy Clock Cycles
SCL
1
2
3
8
9
SDA Released
by EEPROM
Device is
Software Reset
SDA
In the event that the device is still non-responsive or remains active on the SDA bus, a power cycle must be used to
reset the device (see Power-Up Requirements and Reset Behavior).
DS20006197C-page 15
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Memory Organization
6.
Memory Organization
The AT24CM02 is internally organized as 1,024 pages of 256 bytes each.
6.1
Device Addressing
Accessing the device requires an 8-bit device address byte following a Start condition to enable the device for a read
or write operation. Since multiple client devices can reside on the serial bus, each client device must have its own
unique address so the host can access each device independently.
The Most Significant four bits of the device address byte is referred to as the device type identifier. The device type
identifier ‘1010’ (Ah) is required in bits 7‑4 of the device address byte (see Table 6‑1).
Following the 4-bit device type identifier is the hardware client address bit, A2. This bit can be used to expand the
address space by allowing up to two Serial EEPROM devices on the same bus. The hardware client address bit
must correlate with the voltage level on the corresponding hardwired device address input pin A2. The A2 pin uses
an internal proprietary circuit that automatically biases the pin to a logic ‘0’ state if the pin is allowed to float. In
order to operate in a wide variety of application environments, the pull‑down mechanism is intentionally designed to
be somewhat strong. Once the pin is biased above the CMOS input buffer's trip point (~0.5 x VCC), the pull‑down
mechanism disengages. Microchip recommends connecting the A2 pin to a known state whenever possible.
Following the A2 hardware client address bit are A17 and A16 (bit 2 and bit 1 of the device address byte), which are
the Most Significant bits of the memory array word address (see Table 6‑1).
The eighth bit (bit 0) of the device address byte is the Read/Write Select bit. A read operation is initiated if this bit is
high and a write operation is initiated if this bit is low.
Upon the successful comparison of the device address byte, the AT24CM02 will return an ACK. If a valid comparison
is not made, the device will NACK.
Table 6-1.ꢀDevice Address Byte
Most Significant Bits
of the Word Address
Device Type Identifier
Hardware Client Address Bit
R/W Select
Package
Bit 7 Bit 6 Bit 5 Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
1
0
1
0
All Packages
A2
A17
A16
R/W
For all operations except the current address read, two 8‑bit word address bytes must be transmitted to the device
immediately following the device address byte. The word address bytes contain the lower 16 significant memory
array address bits, and are used to specify which byte location in the EEPROM to start reading or writing. See Table
6-2 and Table 6-3 to review their bit positions.
Table 6-2.ꢀFirst Word Address Byte
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
A15
A14
A13
A12
A11
A10
A9
A8
Table 6-3.ꢀSecond Word Address Byte
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
A7
A6
A5
A4
A3
A2
A1
A0
DS20006197C-page 16
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Write Operations
7.
Write Operations
All write operations for the AT24CM02 begin with the host sending a Start condition, followed by a device address
byte with the R/W bit set to logic ‘0’, and then by the word address bytes. The data value(s) to be written to the
device immediately follow the word address bytes.
7.1
Byte Write
The AT24CM02 supports the writing of a single 8-bit byte. Selecting a data word in the AT24CM02 requires 18-bit
word address.
Upon receipt of the proper device address and the word address bytes, the EEPROM will send an Acknowledge. The
device will then be ready to receive the 8-bit data word. Following receipt of the 8‑bit data word, the EEPROM will
respond with an ACK. The addressing device, such as a bus host, must then terminate the write operation with a
Stop condition. At that time, the EEPROM will enter an internally self-timed write cycle, which will be completed within
tWR, while the data word is being programmed into the nonvolatile EEPROM. All inputs are disabled during this write
cycle and the EEPROM will not respond until the write is complete.
Figure 7-1.ꢀByte Write
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
SCL
Device Address Byte
First Word Address Byte
1
0
1
0
A2
A1 A16
0
0
A15 A14 A13 A12 A11 A10 A9 A8
MSb
0
SDA
MSb
Start Condition
by Host
ACK
from Client
ACK
from Client
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
Data Word
Second Word Address Byte
D7 D6 D5 D4 D3 D2 D1 D0
MSb
0
A7 A6 A5 A4 A3 A2 A1 A0
MSb
0
Stop Condition
by Host
ACK
from Client
ACK
from Client
7.2
Page Write
A page write operation allows up to 256 bytes to be written in the same write cycle, provided all bytes are in the same
row of the memory array (where address bits A17 through A8 are the same). Partial page writes of less than 256
bytes are also allowed.
A page write is initiated the same way as a byte write, but the bus host does not send a Stop condition after the first
data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the bus host can
transmit up to 255 additional data words. The EEPROM will respond with an ACK after each data word is received.
Once all data to be written has been sent to the device, the bus host must issue a Stop condition (see Figure 7-2) at
which time the internally self-timed write cycle will begin.
The lower eight bits of the word address are internally incremented following the receipt of each data word. The
higher order address bits are not incremented and retain the memory page row location. Page write operations are
limited to writing bytes within a single physical page, regardless of the number of bytes actually being written. When
the incremented word address reaches the page boundary, the address counter will rollover to the beginning of the
same page. Nevertheless, creating a rollover event should be avoided as previously loaded data in the page could
become unintentionally altered.
DS20006197C-page 17
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Write Operations
Figure 7-2.ꢀ Page Write
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
SCL
Device Address Byte
A2 A1 A16
First Word Address Byte
1
0
1
0
0
0
A15 A14 A13 A12 A11 A10 A9 A8
MSb
0
SDA
MSb
Start Condition
by Host
ACK
from Client
ACK
from Client
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
Second Word Address Byte
Data Word (n)
Data Word (n+x), max of 256 without rollover
A7 A6 A5 A4 A3 A2 A1 A0
MSb
0
D7 D6 D5 D4 D3 D2 D1 D0
MSb
0
D7 D6 D5 D4 D3 D2 D1 D0
MSb
0
Stop Condition
ACK
by Host
ACK
ACK
from Client
from Client
from Client
7.3
Internal Writing Methodology
The AT24CM02 incorporates a built-in error detection and correction (EDC) logic scheme. The EEPROM array is
internally organized as a group of four connected 8-bit bytes plus an additional six ECC (Error Correction Code) bits
of EEPROM. These 38 bits are referred to as the internal physical data word. During a read sequence, the EDC logic
compares each 4-byte physical data word with its corresponding six ECC bits. If a single bit out of the 4-byte region
reads incorrectly, the EDC logic will detect the bad bit and replace it with a correct value before the data is serially
clocked out. This architecture significantly improves the reliability of the AT24CM02 compared to an implementation
that does not utilize EDC.
It is important to note that data is always physically written to the part at the internal physical data word level,
regardless of the number of bytes written. Writing single bytes is still possible with the byte write operation, but
internally, the other three bytes within that 4-byte location where the single byte was written, along with the six ECC
bits, will be updated. Due to this architecture, the AT24CM02 EEPROM write endurance is rated at the internal
physical data word level (4-byte word). The system designer needs to optimize the application writing algorithms to
observe these internal word boundaries in order to reach the endurance rating.
7.4
Acknowledge Polling
An Acknowledge Polling routine can be implemented to optimize time-sensitive applications that would prefer not to
wait the fixed maximum write cycle time (tWR). This method allows the application to know immediately when the
Serial EEPROM write cycle has completed, so a subsequent operation can be started.
Once the internally self-timed write cycle has started, an Acknowledge Polling routine can be initiated. This involves
repeatedly sending a Start condition followed by a valid device address byte with the R/W bit set at logic ‘0’. The
device will not respond with an ACK while the write cycle is ongoing. Once the internal write cycle has completed, the
EEPROM will respond with an ACK, allowing a new read or write operation to be immediately initiated. A flowchart
has been included below in Figure 7-3 to better illustrate this technique.
DS20006197C-page 18
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Write Operations
Figure 7-3.ꢀAcknowledge Polling Flowchart
Send
Stop
condition
Send Start
condition followed
by a valid
Proceed to
next Read or
Write operation.
Did
the device
ACK?
Send any
Write
protocol.
YES
to initiate the
Write cycle.
Device Address
byte with R/W = 0.
NO
7.5
Write Cycle Timing
The length of the self-timed write cycle (tWR) is defined as the amount of time from the Stop condition that begins the
internal write cycle to the Start condition of the first device address byte sent to the AT24CM02 that it subsequently
responds to with an ACK. Figure 7-4 has been included to show this measurement. During the internally self-timed
write cycle, any attempts to read from or write to the memory array will not be processed.
Figure 7-4.ꢀWrite Cycle Timing
SCL
SDA
8
9
9
Data Word n
D0
ACK
ACK
First Acknowledge from the device
to a valid device address sequence after
write cycle is initiated. The minimum tWR
can only be determined through
tWR
the use of an ACK Polling routine.
Stop
Start
Stop
Condition
Condition
Condition
7.6
Write Protection
The AT24CM02 utilizes a hardware data protection scheme that allows the user to write‑protect the entire memory
contents when the WP pin is at VCC (or a valid VIH). No write protection will be set if the WP pin is at GND or left
floating.
Table 7-1.ꢀAT24CM02 Write-Protect Behavior
WP Pin Voltage
Part of the Array Protected
Full Array
VCC
GND
None - Write Protection Not Enabled
The status of the WP pin is sampled at the Stop condition for every byte write or page write operation prior to the
start of an internally self‑timed write cycle. Changing the WP pin state after the Stop condition has been sent will not
alter or interrupt the execution of the write cycle. The WP pin state must be valid with respect to the associated setup
(tSU.WP) and hold (tHD.WP) timing as shown in Figure 7-5 below. The WP setup time is the amount of time that
the WP state must be stable before the Stop condition is issued. The WP hold time is the amount of time after the
DS20006197C-page 19
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Write Operations
Stop condition that the WP must remain stable (see Table 4-3, AC Characteristics,” for timing specs for tHD.WP and
tSU.WP).
If an attempt is made to write to the device while the WP pin has been asserted, the device will acknowledge the
device address, word address and data bytes. However, no write cycle will occur when the Stop condition is issued.
The device will immediately be ready to accept a new read or write command.
Figure 7-5.ꢀWrite-Protect Setup and Hold Timing
DS20006197C-page 20
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Read Operations
8.
Read Operations
Read operations are initiated the same way as write operations with the exception that the Read/Write Select bit in
the device address byte must be a logic ‘1’. There are three read operations:
•
•
•
Current Address Read
Random Address Read
Sequential Read
8.1
Current Address Read
The internal data word address counter maintains the last address accessed during the last read or write operation,
incremented by one. This address stays valid between operations as long as the VCC is maintained to the part. The
address rollover during a read is from the last byte of the last page to the first byte of the first page of the memory.
A current address read operation will output data according to the location of the internal data word address counter.
This is initiated with a Start condition, followed by a valid device address byte with the R/W bit set to logic ‘1’. The
device will ACK this sequence and the current address data word is serially clocked out on the SDA line. All types
of read operations will be terminated if the bus host does not respond with an ACK (it NACKs) during the ninth clock
cycle. After the NACK response, the host may send a Stop condition to complete the protocol or it can send a Start
condition to begin the next sequence.
Figure 8-1.ꢀCurrent Address Read
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
SCL
Device Address Byte
Data Word (n)
1
0
1
0
A2
X
X
1
0
D7 D6 D5 D4 D3 D2 D1 D0
MSb
1
SDA
MSb
Start Condition
by Host
Stop Condition
by Host
from Host
ACK
from Client
NACK
8.2
Random Read
A random read begins in the same way as a byte write operation does to load in a new data word address. This is
known as a “dummy write” sequence; however, the data byte and the Stop condition of the byte write must be omitted
to prevent the part from entering an internal write cycle. Once the device address and word address are clocked in
and acknowledged by the EEPROM, the bus host must generate another Start condition. The bus host now initiates
a current address read by sending a Start condition, followed by a valid device address byte with the R/W bit set to
logic ‘1’. The EEPROM will ACK the device address and serially clock out the data word on the SDA line. All types
of read operations will be terminated if the bus host does not respond with an ACK (it NACKs) during the ninth clock
cycle. After the NACK response, the host may send a Stop condition to complete the protocol, or it can send a Start
condition to begin the next sequence.
DS20006197C-page 21
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Read Operations
Figure 8-2.ꢀRandom Read
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
SCL
Device Address Byte
First Word Address Byte
A14 A13 A12 A11 A10 A9 A8
Second Word Address Byte
1
0
1
0
A2
A1 A16
0
0
0
A7 A6 A5 A4 A3 A2 A1 A0
MSb
0
A15
MSb
SDA
MSb
Start Condition
by Host
ACK
from Client
ACK
from Client
ACK
from Client
Dummy Write
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
Data Word (n)
Device Address Byte
A2 A1
1
0
1
0
A0
1
0
D7 D6 D5 D4 D3 D2 D1 D0
MSb
1
MSb
Start Condition
by Host
Stop Condition
by Host
ACK
from Client
NACK
from Host
8.3
Sequential Read
Sequential reads are initiated by either a current address read or a random read. After the bus host receives a data
word, it responds with an Acknowledge. As long as the EEPROM receives an ACK, it will continue to increment the
word address and serially clock out sequential data words. When the maximum memory address is reached, the data
word address will rollover and the sequential read will continue from the beginning of the memory array. All types of
read operations will be terminated if the bus host does not respond with an ACK (it NACKs) during the ninth clock
cycle. After the NACK response, the host may send a Stop condition to complete the protocol or it can send a Start
condition to begin the next sequence.
Figure 8-3.ꢀSequential Read
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
SCL
SDA
Device Address Byte
Data Word (n)
1
0
1
0
A
A
1
A8
1
0
D7 D6 D5 D4 D3 D2 D1 D0
MSb
0
2
MSb
Start
by
Host
ACK
from
Client
ACK
from
Host
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
Data Word (n+1)
Data Word (n+2)
Data Word (n+x)
D7 D6 D5 D4 D3 D2 D1 D0
MSb
0
D7 D6 D5 D4 D3 D2 D1 D0
MSb
0
D7 D6 D5 D4 D3 D2 D1 D0
MSb
1
Stop
by
Host
ACK
from
Host
ACK
from
Host
NACK
from
Host
DS20006197C-page 22
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Device Default Condition from Microchip
9.
Device Default Condition from Microchip
The AT24CM02 is delivered with the EEPROM array set to logic ‘1’, resulting in FFh data in all locations.
DS20006197C-page 23
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Packaging Information
10.
Packaging Information
10.1
Package Marking Information
AT24CM02: Package Marking Information
8-ball WLCSP
8-lead SOIC
ATMLUYWW
## % CO
YYWWNNN
ATMLHYWW
## % CO
YYWWNNN
Note 1:
designates pin 1
Note 2: Package drawings are not to scale
Catalog Number Truncation
AT24CM02
Truncation Code ##: 2H
Date Codes
Voltages
YY = Year
15: 2015
16: 2016
17: 2017
18: 2018
WW = Work Week of Assembly
% = Minimum Voltage
M: 1.7V min
D: 2.5V min
19: 2019
20: 2020
21: 2021
22: 2022
02: Week 2
04: Week 4
...
52: Week 52
Country of Origin
Device Grade
H or U: Industrial Grade
Atmel Truncation
AT: Atmel
CO = Country of Origin
ATM: Atmel
ATML: Atmel
Lot Number or Trace Code
NNN = Alphanumeric Trace Code (2 Characters for small packages)
DS20006197C-page 24
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Packaging Information
8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC]
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2X
0.10 C A–B
D
A
D
NOTE 5
N
E
2
E1
2
E1
E
2X
0.10 C A–B
2X
0.10 C A–B
1
2
NOTE 1
e
NX b
0.25
C A–B D
B
NOTE 5
TOP VIEW
0.10 C
0.10 C
C
A2
A
SEATING
PLANE
8X
SIDE VIEW
A1
h
R0.13
R0.13
h
H
0.23
L
SEE VIEW C
(L1)
VIEW A–A
VIEW C
Microchip Technology Drawing No. C04-057-SN Rev F Sheet 1 of 2
DS20006197C-page 25
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Packaging Information
8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC]
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
Units
MILLIMETERS
Dimension Limits
MIN
NOM
MAX
Number of Pins
Pitch
N
e
8
1.27 BSC
Overall Height
Molded Package Thickness
Standoff
Overall Width
A
-
-
-
-
1.75
-
0.25
A2
A1
E
1.25
0.10
§
6.00 BSC
Molded Package Width
Overall Length
E1
D
3.90 BSC
4.90 BSC
Chamfer (Optional)
Foot Length
h
L
0.25
0.40
-
-
0.50
1.27
Footprint
L1
1.04 REF
Foot Angle
Lead Thickness
Lead Width
Mold Draft Angle Top
Mold Draft Angle Bottom
0°
0.17
0.31
5°
-
-
-
-
-
8°
c
0.25
0.51
15°
b
5°
15°
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. § Significant Characteristic
3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or
protrusions shall not exceed 0.15mm per side.
4. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
5. Datums A & B to be determined at Datum H.
Microchip Technology Drawing No. C04-057-SN Rev F Sheet 2 of 2
DS20006197C-page 26
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Packaging Information
8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC]
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
SILK SCREEN
C
Y1
X1
E
RECOMMENDED LAND PATTERN
Units
Dimension Limits
MILLIMETERS
NOM
MIN
MAX
Contact Pitch
E
C
X1
Y1
1.27 BSC
5.40
Contact Pad Spacing
Contact Pad Width (X8)
Contact Pad Length (X8)
0.60
1.55
Notes:
1. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
Microchip Technology Drawing C04-2057-SN Rev F
DS20006197C-page 27
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Packaging Information
TOP VIEW
BOTTOM SIDE
k 0.015 (4X)
A
A1 CORNER
A1 CORNER
1 2
3 4
4 3
2 1
A
A
B
B
e1
E
C
D
C
D
e
db
d1
d2
D
m
m
d0.015
C
v
d
0.05
C A B
SIDE VIEW
A2
COMMON DIMENSIONS
(Unit of Measure = mm)
SEATING PLANE A
-C-
SYMBOL
A
MIN
TYP
MAX
NOTE
A1
0.456
0.495
0.534
k 0.20
C
A1
A2
D
—
—
0.190
0.305
—
—
PIN ASSIGNMENT MATRIX
Contact Microchip for details.
1.00 BSC
d1
d2
E
1
2
3
4
1.40 BSC
A
B
C
D
n/a
n/a
SCL
n/a
VCC
WP
n/a
NC
n/a
n/a
NC
A2
Contact Microchip for details.
0.50 BSC
e
n/a
e1
b
2.10 BSC
SDA
GND
n/a
—
0.270
—
NC = Not Connected
Note: 1. Dimensions are NOT to scale.
2. Solder ball composition is 95.5Sn-4.0Ag-0.5Cu.
4/5/16
TITLE
GPC
DRAWING NO.
REV.
8U-18, 8-ball 4x4 Array, Custom Pitch
Wafer Level Chip Scale Package (WLCSP)
GQA
8U-18
01
Note:ꢀ For the most current package drawings, please see the Microchip Packaging Specification located at http://
www.microchip.com/packaging.
DS20006197C-page 28
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Revision History
11.
Revision History
Revision C (March 2021)
Corrected SOIC Package Type drawing. Updated the SOIC package drawing.
Revision B (December 2020)
Updated Revision History to latest template. Removed thin height WLCSP product offering. Replaced terminology
“Master” and “Slave” with “Host” and “Client”, respectively.
Revision A (May 2019)
Updated to Microchip template. Microchip DS20006197 replaces Atmel document 8812. Corrected tLOW typo from
400 ns to 500 ns. Corrected tAA typo from 550 ns to 450 ns. Updated Part Marking Information. Updated the
“Software Reset” section. Added ESD rating. Removed lead finish designation. Updated trace code format in
package markings. Updated section content throughout for clarification. Updated SOIC package drawing to Microchip
format.
Atmel Document 8828 Revision E (January 2017)
Updated Power-on Requirements and Reset Behavior section.
Atmel Document 8828 Revision D (May 2016)
Added the 8U-18 standard thickness WLCSP package option. Updated the “Clock and Data Transition
Requirements” section and the “DC Characteristics” table.
Atmel Document 8828 Revision C (November 2015)
Corrected 8-ball WLCSP pinout.
Atmel Document 8828 Revision B (August 2015)
Updated the 8U-11 package drawing, data retention discrepancy and 8-ball pinout.
Atmel Document 8828 Revision A (May 2015)
Initial document release.
DS20006197C-page 29
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
The Microchip Website
Microchip provides online support via our website at www.microchip.com/. This website is used to make files and
information easily available to customers. Some of the content available includes:
•
•
•
Product Support – Data sheets and errata, application notes and sample programs, design resources, user’s
guides and hardware support documents, latest software releases and archived software
General Technical Support – Frequently Asked Questions (FAQs), technical support requests, online
discussion groups, Microchip design partner program member listing
Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of
seminars and events, listings of Microchip sales offices, distributors and factory representatives
Product Change Notification Service
Microchip’s product change notification service helps keep customers current on Microchip products. Subscribers will
receive email notification whenever there are changes, updates, revisions or errata related to a specified product
family or development tool of interest.
To register, go to www.microchip.com/pcn and follow the registration instructions.
Customer Support
Users of Microchip products can receive assistance through several channels:
•
•
•
•
Distributor or Representative
Local Sales Office
Embedded Solutions Engineer (ESE)
Technical Support
Customers should contact their distributor, representative or ESE for support. Local sales offices are also available to
help customers. A listing of sales offices and locations is included in this document.
Technical support is available through the website at: www.microchip.com/support
DS20006197C-page 30
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
Product Identification System
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
A T 2 4 C M 0 2 - S S H D - B
Shipping Carrier Option
B
T
E
= Bulk (Tubes)
= Tape and Reel, Standard Quantity Option
= Tape and Reel, Extended Quantity Option
Product Family
24C = Standard I2C-compatible
Serial EEPROM
Operating Voltage
D = 2.5V to 5.5V
M = 1.7V to 5.5V
Device Grade or
Wafer/Die Thickness
H or U = Industrial Temperature Range
(-40°C to +85°C)
Device Density
M = Megabit Family
02 = 2 Megabit
11
= 11mil Wafer Thickness
Package Option
SS
U2
= SOIC
= WLCSP
WWU = Wafer Unsawn
Examples
Package
Package Drawing
Code
Shipping
Carrier
Option
Package
Option
Device
Voltage
Device Grade
1.7V to
5.5V
Bulk
(Tubes)
AT24CM02‑SSHM‑B
AT24CM02‑SSHM‑T
AT24CM02‑SSHD‑B
AT24CM02‑SSHD‑T
AT24CM02‑U2UM‑T(1)
Note:ꢀ
SOIC
SOIC
SN
SN
SS
SS
SS
SS
U2
1.7V to
5.5V
Tape and
Reel
Industrial Temperature
(-40°C to +85°C)
2.5V to
5.5V
Bulk
(Tubes)
SOIC
SN
2.5V to
5.5V
Tape and
Reel
SOIC
SN
1.7V to
5.5V
Tape and
Reel
WLCSP
8U-18
1. CAUTION: Exposure to ultraviolet (UV) light can degrade the data stored in EEPROM cells. Therefore,
customers who use a WLCSP package or the product at a die level must ensure that exposure to ultraviolet
light does not occur.
Microchip Devices Code Protection Feature
Note the following details of the code protection feature on Microchip devices:
•
•
Microchip products meet the specifications contained in their particular Microchip Data Sheet.
Microchip believes that its family of products is secure when used in the intended manner and under normal
conditions.
•
There are dishonest and possibly illegal methods being used in attempts to breach the code protection features
of the Microchip devices. We believe that these methods require using the Microchip products in a manner
DS20006197C-page 31
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
outside the operating specifications contained in Microchip’s Data Sheets. Attempts to breach these code
protection features, most likely, cannot be accomplished without violating Microchip’s intellectual property rights.
•
•
Microchip is willing to work with any customer who is concerned about the integrity of its code.
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of its code. Code
protection does not mean that we are guaranteeing the product is “unbreakable.” Code protection is constantly
evolving. We at Microchip are committed to continuously improving the code protection features of our products.
Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act.
If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue
for relief under that Act.
Legal Notice
Information contained in this publication is provided for the sole purpose of designing with and using Microchip
products. Information regarding device applications and the like is provided only for your convenience and may be
superseded by updates. It is your responsibility to ensure that your application meets with your specifications.
THIS INFORMATION IS PROVIDED BY MICROCHIP “AS IS”. MICROCHIP MAKES NO REPRESENTATIONS
OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY
OR OTHERWISE, RELATED TO THE INFORMATION INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE
OR WARRANTIES RELATED TO ITS CONDITION, QUALITY, OR PERFORMANCE.
IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL OR
CONSEQUENTIAL LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE
INFORMATION OR ITS USE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE
POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE FULLEST EXTENT ALLOWED BY LAW,
MICROCHIP'S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY RELATED TO THE INFORMATION OR ITS USE
WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY, THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR
THE INFORMATION. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk,
and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or
expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual
property rights unless otherwise stated.
Trademarks
The Microchip name and logo, the Microchip logo, Adaptec, AnyRate, AVR, AVR logo, AVR Freaks, BesTime,
BitCloud, chipKIT, chipKIT logo, CryptoMemory, CryptoRF, dsPIC, FlashFlex, flexPWR, HELDO, IGLOO, JukeBlox,
KeeLoq, Kleer, LANCheck, LinkMD, maXStylus, maXTouch, MediaLB, megaAVR, Microsemi, Microsemi logo,
MOST, MOST logo, MPLAB, OptoLyzer, PackeTime, PIC, picoPower, PICSTART, PIC32 logo, PolarFire, Prochip
Designer, QTouch, SAM-BA, SenGenuity, SpyNIC, SST, SST Logo, SuperFlash, Symmetricom, SyncServer,
Tachyon, TimeSource, tinyAVR, UNI/O, Vectron, and XMEGA are registered trademarks of Microchip Technology
Incorporated in the U.S.A. and other countries.
AgileSwitch, APT, ClockWorks, The Embedded Control Solutions Company, EtherSynch, FlashTec, Hyper Speed
Control, HyperLight Load, IntelliMOS, Libero, motorBench, mTouch, Powermite 3, Precision Edge, ProASIC,
ProASIC Plus, ProASIC Plus logo, Quiet-Wire, SmartFusion, SyncWorld, Temux, TimeCesium, TimeHub, TimePictra,
TimeProvider, WinPath, and ZL are registered trademarks of Microchip Technology Incorporated in the U.S.A.
Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, Augmented Switching,
BlueSky, BodyCom, CodeGuard, CryptoAuthentication, CryptoAutomotive, CryptoCompanion, CryptoController,
dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM, ECAN, Espresso T1S, EtherGREEN, IdealBridge,
In-Circuit Serial Programming, ICSP, INICnet, Intelligent Paralleling, Inter-Chip Connectivity, JitterBlocker, maxCrypto,
maxView, memBrain, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach,
Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE,
Ripple Blocker, RTAX, RTG4, SAM-ICE, Serial Quad I/O, simpleMAP, SimpliPHY, SmartBuffer, SMART-I.S., storClad,
SQI, SuperSwitcher, SuperSwitcher II, Switchtec, SynchroPHY, Total Endurance, TSHARC, USBCheck, VariSense,
VectorBlox, VeriPHY, ViewSpan, WiperLock, XpressConnect, and ZENA are trademarks of Microchip Technology
Incorporated in the U.S.A. and other countries.
DS20006197C-page 32
Datasheet
© 2019-2021 Microchip Technology Inc.
AT24CM02
SQTP is a service mark of Microchip Technology Incorporated in the U.S.A.
The Adaptec logo, Frequency on Demand, Silicon Storage Technology, and Symmcom are registered trademarks of
Microchip Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip
Technology Inc., in other countries.
All other trademarks mentioned herein are property of their respective companies.
©
2019-2021, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved.
ISBN: 978-1-5224-7822-5
AMBA, Arm, Arm7, Arm7TDMI, Arm9, Arm11, Artisan, big.LITTLE, Cordio, CoreLink, CoreSight, Cortex, DesignStart,
DynamIQ, Jazelle, Keil, Mali, Mbed, Mbed Enabled, NEON, POP, RealView, SecurCore, Socrates, Thumb,
TrustZone, ULINK, ULINK2, ULINK-ME, ULINK-PLUS, ULINKpro, µVision, Versatile are trademarks or registered
trademarks of Arm Limited (or its subsidiaries) in the US and/or elsewhere.
Quality Management System
For information regarding Microchip’s Quality Management Systems, please visit www.microchip.com/quality.
DS20006197C-page 33
Datasheet
© 2019-2021 Microchip Technology Inc.
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
www.microchip.com/support
Web Address:
Australia - Sydney
Tel: 61-2-9868-6733
China - Beijing
India - Bangalore
Tel: 91-80-3090-4444
India - New Delhi
Tel: 91-11-4160-8631
India - Pune
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4485-5910
Tel: 86-10-8569-7000
China - Chengdu
Tel: 86-28-8665-5511
China - Chongqing
Tel: 86-23-8980-9588
China - Dongguan
Tel: 86-769-8702-9880
China - Guangzhou
Tel: 86-20-8755-8029
China - Hangzhou
Tel: 86-571-8792-8115
China - Hong Kong SAR
Tel: 852-2943-5100
China - Nanjing
Tel: 91-20-4121-0141
Japan - Osaka
Fax: 45-4485-2829
Finland - Espoo
Tel: 81-6-6152-7160
Japan - Tokyo
Tel: 358-9-4520-820
France - Paris
www.microchip.com
Atlanta
Tel: 81-3-6880- 3770
Korea - Daegu
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Germany - Garching
Tel: 49-8931-9700
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Austin, TX
Tel: 82-53-744-4301
Korea - Seoul
Tel: 82-2-554-7200
Malaysia - Kuala Lumpur
Tel: 60-3-7651-7906
Malaysia - Penang
Tel: 60-4-227-8870
Philippines - Manila
Tel: 63-2-634-9065
Singapore
Germany - Haan
Tel: 512-257-3370
Boston
Tel: 49-2129-3766400
Germany - Heilbronn
Tel: 49-7131-72400
Germany - Karlsruhe
Tel: 49-721-625370
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Germany - Rosenheim
Tel: 49-8031-354-560
Israel - Ra’anana
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Tel: 86-25-8473-2460
China - Qingdao
Tel: 86-532-8502-7355
China - Shanghai
Tel: 86-21-3326-8000
China - Shenyang
Tel: 86-24-2334-2829
China - Shenzhen
Tel: 86-755-8864-2200
China - Suzhou
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Tel: 65-6334-8870
Taiwan - Hsin Chu
Tel: 886-3-577-8366
Taiwan - Kaohsiung
Tel: 886-7-213-7830
Taiwan - Taipei
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Tel: 972-9-744-7705
Italy - Milan
Tel: 86-186-6233-1526
China - Wuhan
Tel: 886-2-2508-8600
Thailand - Bangkok
Tel: 66-2-694-1351
Vietnam - Ho Chi Minh
Tel: 84-28-5448-2100
Tel: 39-0331-742611
Fax: 39-0331-466781
Italy - Padova
Novi, MI
Tel: 248-848-4000
Houston, TX
Tel: 86-27-5980-5300
China - Xian
Tel: 39-049-7625286
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Norway - Trondheim
Tel: 47-72884388
Tel: 281-894-5983
Indianapolis
Tel: 86-29-8833-7252
China - Xiamen
Noblesville, IN
Tel: 86-592-2388138
China - Zhuhai
Tel: 317-773-8323
Fax: 317-773-5453
Tel: 317-536-2380
Los Angeles
Tel: 86-756-3210040
Poland - Warsaw
Tel: 48-22-3325737
Romania - Bucharest
Tel: 40-21-407-87-50
Spain - Madrid
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Tel: 951-273-7800
Raleigh, NC
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Sweden - Gothenberg
Tel: 46-31-704-60-40
Sweden - Stockholm
Tel: 46-8-5090-4654
UK - Wokingham
Tel: 919-844-7510
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
Tel: 408-436-4270
Canada - Toronto
Tel: 905-695-1980
Fax: 905-695-2078
Tel: 44-118-921-5800
Fax: 44-118-921-5820
DS20006197C-page 34
Datasheet
© 2019-2021 Microchip Technology Inc.
相关型号:
©2020 ICPDF网 联系我们和版权申明