24C01CT-E/SNA24 [MICROCHIP]
128 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8, 3.90 MM, ROHS COMPLIANT, PLASTIC, SOIC-8;型号: | 24C01CT-E/SNA24 |
厂家: | MICROCHIP |
描述: | 128 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8, 3.90 MM, ROHS COMPLIANT, PLASTIC, SOIC-8 可编程只读存储器 电动程控只读存储器 电可擦编程只读存储器 时钟 光电二极管 内存集成电路 |
文件: | 总36页 (文件大小:957K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
24C01C
1K 5.0V I2C™ Serial EEPROM
Features:
Description:
• Single Supply with Operation from 4.5V to 5.5V
• Low-Power CMOS Technology:
- Read current 1 mA, max.
The Microchip Technology Inc. 24C01C is a 1K bit
Serial Electrically Erasable PROM with a voltage range
of 4.5V to 5.5V. The device is organized as a single
block of 128 x 8-bit memory with a 2-wire serial
interface. Low-current design permits operation with
max. standby and active currents of only 5 A and 1
mA, respectively. The device has a page write capabil-
ity for up to 16 bytes of data and has fast write cycle
times of only 1 ms for both byte and page writes. Func-
tional address lines allow the connection of up to eight
24C01C devices on the same bus for up to 8K bits of
contiguous EEPROM memory. The device is available
in the standard 8-pin PDIP, 8-pin SOIC (3.90 mm),
8-pin 2x3 DFN and TDFN, 8-pin MSOP and TSSOP
packages. The 24C01C is also available in the 6-lead
SOT-23 package.
- Standby current 5 A, max.
• 2-Wire Serial Interface, I2C™ Compatible
• Cascadable up to Eight Devices
• Schmitt Trigger Inputs for Noise Suppression
• Output Slope Control to Eliminate Ground Bounce
• 100 kHz and 400 kHz Clock Compatibility
• Page Write Time 1 ms max.
• Self-Timed Erase/Write Cycle
• 16-Byte Page Write Buffer
• ESD Protection >4000V
• More than 1 Million Erase/Write Cycles
• Data Retention >200 Years
Block Diagram
• Factory Programming Available
• Packages include 8-lead PDIP, SOIC, TSSOP,
DFN, TDFN, MSOP and 6-lead SOT-23
A0 A1 A2
HV Generator
• Pb-Free and RoHS Compliant
• Temperature Ranges:
I/O
Control
Logic
Memory
Control
Logic
- Industrial (I):
-40C to +85C
-40C to +125C
EEPROM
Array
- Automotive (E):
XDEC
SDA
SCL
VCC
YDEC
VSS
Sense Amp.
R/W Control
Package Types
PDIP, MSOP
SOT-23
DFN/TDFN
SOIC, TSSOP
VCC
A0
SCL
VSS
6
1
2
3
1
VCC
Test
SCL
SDA
A0
A1
8
7
6
5
A0
1
8
VCC
A0
1
2
8
7
VCC
Test
SCL
SDA
2
3
4
5
A1
A2
2
3
7
6
Test
A1
A2
VSS
SCL
A2
4
3
4
6
5
A1
SDA
VSS
4
5
SDA
VSS
1997-2012 Microchip Technology Inc.
DS21201K-page 1
24C01C
1.0
ELECTRICAL CHARACTERISTICS
(†)
Absolute Maximum Ratings
VCC.............................................................................................................................................................................7.0V
All inputs and outputs w.r.t. VSS ......................................................................................................... -0.6V to VCC +1.0V
Storage temperature ...............................................................................................................................-65°C to +150°C
Ambient temperature with power applied................................................................................................-40°C to +125°C
ESD protection on all pins 4 kV
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at these or any other conditions above those
indicated in the operational listings of this specification is not implied. Exposure to Absolute Maximum Rating
conditions for extended periods may affect device reliability.
TABLE 1-1:
DC CHARACTERISTICS
Electrical Characteristics:
DC CHARACTERISTICS
Industrial (I):
Automotive (E): VCC = +4.5V to 5.5V
VCC = +4.5V to 5.5V
TA = -40°C to +85°C
TA = -40°C to +125°C
Param.
Sym.
No.
Characteristic
Min.
Max.
Units
Conditions
D1
—
A0, A1, A2, SCL, SDA
and WP pins:
—
—
—
—
D2
D3
VIH
VIL
High-level input voltage
Low-level input voltage
0.7 VCC
—
—
V
V
—
—
0.3 VCC
D4
VHYS
Hysteresis of Schmitt
Trigger inputs
0.05 VCC
—
V
(Note)
(SDA, SCL pins)
D5
D6
VOL
ILI
Low-level output voltage
Input leakage current
Output leakage current
—
—
0.40
±1
V
IOL = 3.0 mA @ VCC = 4.5V
VIN = VSS or VCC, WP = VSS
VOUT = VSS or VCC
A
D7
D8
ILO
—
—
±1
10
A
CIN,
Pin capacitance
pF
VCC = 5.0V (Note)
COUT
(all inputs/outputs)
TA = 25°C, f = 1 MHz
D9
ICC Read Operating current
ICC Write
—
—
—
1
3
5
mA
mA
A
VCC = 5.5V, SCL = 400 kHz
VCC = 5.5V
D10
ICCS
Standby current
VCC = 5.5V, SDA = SCL = VCC
WP = VSS
Note: This parameter is periodically sampled and not 100% tested.
DS21201K-page 2
1997-2012 Microchip Technology Inc.
24C01C
TABLE 1-2:
AC CHARACTERISTICS
Electrical Characteristics:
AC CHARACTERISTICS
Industrial (I):
Automotive (E): VCC = +4.5V to 5.5V
VCC = +4.5V to 5.5V
TA = -40°C to +85°C
TA = -40°C to +125°C
Param.
Sym.
No.
Characteristic
Clock frequency
Min.
Max.
Units
Conditions
1
2
3
4
5
6
7
FCLK
THIGH
TLOW
TR
—
—
100
400
kHz
—
(I-temp)
Clock high time
Clock low time
4000
600
—
—
ns
ns
ns
ns
ns
ns
—
(I-temp)
4700
1300
—
—
—
(I-temp)
SDA and SCL rise time
(Note 1)
—
—
1000
300
—
(I-temp)
TF
SDA and SCL fall time
(Note 1)
—
300
—
THD:STA Start condition hold time
TSU:STA Start condition setup time
4000
600
—
—
—
(I-temp)
4700
600
—
—
—
(I-temp)
8
9
THD:DAT Data input hold time
TSU:DAT Data input setup time
0
—
ns
ns
(Note 2)
250
100
—
—
—
(I-temp)
10
11
12
TSU:STO Stop condition setup time
4000
600
—
—
ns
ns
ns
—
(I-temp)
TAA
Output valid from clock
—
—
3500
900
—
(I-temp)
(Note 2)
TBUF
Bus free time: Time the bus
must be free before a new
transmission can start
4700
1300
—
—
—
(I-temp)
13
TOF
Output fall time from VIH
minimum to VIL maximum
CB 100 pF
10 + 0.1CB
250
50
ns
(Note 1)
(Note 3)
14
15
16
TSP
TWC
—
Input filter spike suppression
(SDA and SCL pins)
—
—
ns
Write cycle time (byte or
page)
1.5
1
ms
—
(I-temp)
Endurance
1,000,000
—
cycles 25°C (Note 4)
Note 1: Not 100% tested. CB = total capacitance of one bus line in pF.
2: As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region
(minimum 300 ns) of the falling edge of SCL to avoid unintended generation of Start or Stop conditions.
3: The combined TSP and VHYS specifications are due to new Schmitt Trigger inputs, which provide improved
noise spike suppression. This eliminates the need for a TI specification for standard operation.
4: This parameter is not tested but ensured by characterization. For endurance estimates in a specific
application, please consult the Total Endurance™ Model, which can be obtained from Microchip’s web site
at www.microchip.com.
1997-2012 Microchip Technology Inc.
DS21201K-page 3
24C01C
FIGURE 1-1:
BUS TIMING DATA
5
4
D4
2
SCL
7
3
10
8
9
SDA
IN
6
14
12
11
SDA
OUT
DS21201K-page 4
1997-2012 Microchip Technology Inc.
24C01C
2.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 2-1.
TABLE 2-1:
Name
PIN FUNCTION TABLE
8-pin
PDIP
8-pin
SOIC
8-pin
TSSOP
8-pin
MSOP
8-pin
DFN/TDFN
SOT-23
Function
A0
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
5
4
Chip Select
A1
Chip Select
Chip Select
Ground
A2
—
2
VSS
SDA
SCL
Test
VCC
3
Serial Data
1
Serial Clock
Test
—
6
+4.5V to 5.5V Power Supply
2.1
SDA Serial Data
2.5
Noise Protection
This is a bidirectional pin used to transfer addresses
and data into and data out of the device. It is an open
drain terminal; therefore, the SDA bus requires a pull-
up resistor to VCC (typical 10 k for 100 kHz, 2 k for
400 kHz).
The 24C01C employs a VCC threshold detector circuit
which disables the internal erase/write logic if the VCC
is below 3.8 volts at nominal conditions.
The SCL and SDA inputs have Schmitt Trigger and
filter circuits which suppress noise spikes to assure
proper device operation even on a noisy bus.
For normal data transfer SDA is allowed to change only
during SCL low. Changes during SCL high are
reserved for indicating the Start and Stop conditions.
2.2
SCL Serial Clock
This input is used to synchronize the data transfer from
and to the device.
2.3
A0, A1, A2
The levels on these inputs are compared with the
corresponding bits in the slave address. The chip is
selected if the compare is true.
Up to eight 24C01C devices may be connected to the
same bus by using different Chip Select bit combina-
tions. These inputs must be connected to either VCC or
VSS.
For the SOT-23 devices up to four devices may be con-
nected to the same bus using different Chip Select bit
combinations.
In most applications, the chip address inputs A0, A1
and A2 are hard-wired to logic ‘0’ or logic ‘1’. For
applications in which these pins are controlled by a
microcontroller or other programmable device, the chip
address pins must be driven to logic ‘0’ or logic ‘1’
before normal device operation can proceed.
2.4
Test
This pin is utilized for testing purposes only. It may be
tied high, tied low or left floating.
1997-2012 Microchip Technology Inc.
DS21201K-page 5
24C01C
4.4
Data Valid (D)
3.0
FUNCTIONAL DESCRIPTION
The state of the data line represents valid data when,
after a Start condition, the data line is stable for the
duration of the high period of the clock signal.
The 24C01C supports a bidirectional 2-wire bus and
data transmission protocol. A device that sends data
onto the bus is defined as transmitter, and a device
receiving data as receiver. The bus has to be controlled
by a master device that generates the Serial Clock
(SCL), controls the bus access, and generates the Start
and Stop conditions, while the 24C01C works as slave.
Both master and slave can operate as transmitter or
receiver, but the master device determines which mode
is activated.
The data on the line must be changed during the low
period of the clock signal. There is one bit of data per
clock pulse.
Each data transfer is initiated with a Start condition and
terminated with a Stop condition. The number of the
data bytes transferred between the Start and Stop
conditions is determined by the master device and is
theoretically unlimited, although only the last sixteen
will be stored when doing a write operation. When an
overwrite does occur it will replace data in a first-in first-
out fashion.
4.0
BUS CHARACTERISTICS
The following bus protocol has been defined:
• Data transfer may be initiated only when the bus
is not busy.
4.5
Acknowledge
• During data transfer, the data line must remain
stable whenever the clock line is high. Changes in
the data line while the clock line is high will be
interpreted as a Start or Stop condition.
Each receiving device, when addressed, is required to
generate an acknowledge after the reception of each
byte. The master device must generate an extra clock
pulse, which is associated with this Acknowledge bit.
Accordingly, the following bus conditions have been
defined (Figure 4-1).
Note:
The 24C01C does not generate any
Acknowledge bits if an internal program-
ming cycle is in progress.
4.1
Bus Not Busy (A)
The device that acknowledges has to pull down the
SDA line during the Acknowledge clock pulse in such a
way that the SDA line is stable low during the high
period of the acknowledge related clock pulse. Of
course, setup and hold times must be taken into
account. A master must signal an end of data to the
slave by not generating an Acknowledge bit on the last
byte that has been clocked out of the slave. In this case,
the slave must leave the data line high to enable the
master to generate the Stop condition (Figure 4-2)
Both data and clock lines remain high.
4.2
Start Data Transfer (B)
A high-to-low transition of the SDA line while the clock
(SCL) is high determines a Start condition. All
commands must be preceded by a Start condition.
4.3
Stop Data Transfer (C)
A low-to-high transition of the SDA line while the clock
(SCL) is high determines a Stop condition. All
operations must be ended with a Stop condition.
DS21201K-page 6
1997-2012 Microchip Technology Inc.
24C01C
FIGURE 4-1:
DATA TRANSFER SEQUENCE ON THE SERIAL BUS
(A)
(B)
(C)
(D)
(C) (A)
SCL
SDA
Start
Condition
Stop
Condition
Address or
Acknowledge
Valid
Data
Allowed
to Change
FIGURE 4-2:
ACKNOWLEDGE TIMING
Acknowledge
Bit
1
2
3
4
5
6
7
8
9
1
2
3
SCL
SDA
Data from transmitter
Data from transmitter
Receiver must release the SDA line at this
point so the Transmitter can continue send-
ing data.
Transmitter must release the SDA line at this point
allowing the Receiver to pull the SDA line low to
acknowledge the previous eight bits of data.
1997-2012 Microchip Technology Inc.
DS21201K-page 7
24C01C
FIGURE 5-1:
CONTROL BYTE
FORMAT
5.0
DEVICE ADDRESSING
A control byte is the first byte received following the
Start condition from the master device (Figure 5-1).
The control byte consists of a four-bit control code; for
the 24C01C this is set as ‘1010’ binary for read and
write operations. The next three bits of the control byte
are the Chip Select bits (A2, A1, A0). The Chip Select
bits allow the use of up to eight 24C01C devices on the
same bus and are used to select which device is
accessed. The Chip Select bits in the control byte must
correspond to the logic levels on the corresponding A2,
A1 and A0 pins for the device to respond. These bits
are in effect the three Most Significant bits of the word
address.
Read/Write Bit
Chip Select
Control Code
Bits
S
1
0
1
0
A2 A1 A0 R/W ACK
Slave Address
Acknowledge Bit
Start Bit
For the SOT-23 package, the A2 address pin is not
available. During device addressing, the A2 Chip
Select bit should be set to ‘0’.
5.1
Contiguous Addressing Across
Multiple Devices
The Chip Select bits A2, A1, A0 can be used to expand
the contiguous address space for up to 8K bits by
adding up to eight 24C01C devices on the same bus.
In this case, software can use A0 of the control byte as
address bit A8, A1 as address bit A9, and A2 as
address bit A10. It is not possible to sequentially read
across device boundaries.
The last bit of the control byte defines the operation to
be performed. When set to a ‘1’ a read operation is
selected, and when set to a ‘0’ a write operation is
selected. Following the Start condition, the 24C01C
monitors the SDA bus checking the control byte being
transmitted. Upon receiving a ‘1010’ code and appro-
priate Chip Select bits, the slave device outputs an
Acknowledge signal on the SDA line. Depending on the
state of the R/W bit, the 24C01C will select a read or
write operation.
For the SOT-23 package, up to four 24C01C devices
can be added for up to 4K bits of address space. In this
case, software can use A0 of the control byte as
address bit A8, and A1 as address bit A9. It is not pos-
sible to sequentially read across device boundaries.
DS21201K-page 8
1997-2012 Microchip Technology Inc.
24C01C
After the receipt of each word, the four lower order
Address Pointer bits are internally incremented by one.
The higher order four bits of the word address remains
constant. If the master should transmit more than 16
bytes prior to generating the Stop condition, the
address counter will roll over and the previously
received data will be overwritten. As with the byte write
operation, once the Stop condition is received an
internal write cycle will begin (Figure 6-2).
6.0
6.1
WRITE OPERATIONS
Byte Write
Following the Start signal from the master, the device
code (4 bits), the Chip Select bits (3 bits), and the R/W
bit, which is a logic low, is placed onto the bus by the
master transmitter. The device will acknowledge this
control byte during the ninth clock pulse. The next byte
transmitted by the master is the word address and will
be written into the Address Pointer of the 24C01C.
After receiving another Acknowledge signal from the
24C01C the master device will transmit the data word
to be written into the addressed memory location. The
24C01C acknowledges again and the master gener-
ates a Stop condition. This initiates the internal write
cycle, and during this time the 24C01C will not
generate Acknowledge signals (Figure 6-1).
Note:
Page write operations are limited to writ-
ing bytes within a single physical page,
regardless of the number of bytes actu-
ally being written. Physical page boundar-
ies start at addresses that are integer
multiples of the page buffer size (or ‘page
size’) and end at addresses that are
integer multiples of [page size – 1]. If a
Page Write command attempts to write
across a physical page boundary, the
result is that the data wraps around to the
beginning of the current page (overwriting
data previously stored there), instead of
being written to the next page as might be
expected. It is therefore necessary for the
application software to prevent page write
operations that would attempt to cross a
page boundary.
6.2
Page Write
The write control byte, word address and the first data
byte are transmitted to the 24C01C in the same way as
in a byte write. But instead of generating a Stop
condition, the master transmits up to 15 additional data
bytes to the 24C01C which are temporarily stored in
the on-chip page buffer and will be written into the
memory after the master has transmitted a Stop
condition.
FIGURE 6-1:
BYTE WRITE
S
T
A
R
T
S
T
Bus Activity
Master
Control
Byte
Word
Address
Data
O
P
SDA Line
S
P
A
C
K
A
C
K
A
C
K
Bus Activity
FIGURE 6-2:
PAGE WRITE
S
T
A
R
T
S
T
O
P
Bus Activity
Master
Control
Byte
Word
Address (n)
Data n
Data n +1
Data n + 15
SDA Line
S
P
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
Bus Activity
1997-2012 Microchip Technology Inc.
DS21201K-page 9
24C01C
FIGURE 7-1:
ACKNOWLEDGE
POLLING FLOW
7.0
ACKNOWLEDGE POLLING
Since the device will not acknowledge during a write
cycle, this can be used to determine when the cycle is
complete (this feature can be used to maximize bus
throughput). Once the Stop condition for a Write
command has been issued from the master, the device
initiates the internally timed write cycle. ACK polling
can be initiated immediately. This involves the master
sending a Start condition followed by the control byte
for a Write command (R/W = 0). If the device is still
busy with the write cycle, then no ACK will be returned.
If no ACK is returned, then the Start bit and control byte
must be re-sent. If the cycle is complete, then the
device will return the ACK and the master can then
proceed with the next Read or Write command. See
Figure 7-1 for flow diagram.
Send
Write Command
Send Stop
Condition to
Initiate Write Cycle
Send Start
Send Control Byte
with R/W = 0
NO
Did Device
Acknowledge
(ACK = 0)?
YES
Next
Operation
DS21201K-page 10
1997-2012 Microchip Technology Inc.
24C01C
8.2
Random Read
8.0
READ OPERATION
Random read operations allow the master to access
any memory location in a random manner. To perform
this type of read operation, first the word address must
be set. This is done by sending the word address to the
24C01C as part of a write operation.
Read operations are initiated in the same way as write
operations with the exception that the R/W bit of the
slave address is set to one. There are three basic types
of read operations: current address read, random read
and sequential read.
After the word address is sent, the master generates a
Start condition following the acknowledge. This
terminates the write operation, but not before the
internal Address Pointer is set. Then the master issues
the control byte again but with the R/W bit set to a one.
The 24C01C will then issue an acknowledge and trans-
mits the eight bit data word. The master will not
acknowledge the transfer, but does generate a Stop
condition and the 24C01C discontinues transmission
(Figure 8-2). After this command, the internal address
counter will point to the address location following the
one that was just read.
8.1
Current Address Read
The 24C01C contains an address counter that main-
tains the address of the last word accessed, internally
incremented by one. Therefore, if the previous read
access was to address n, the next current address read
operation would access data from address n + 1. Upon
receipt of the slave address with the R/W bit set to one,
the 24C01C issues an acknowledge and transmits the
eight-bit data word. The master will not acknowledge
the transfer, but does generate a Stop condition and the
24C01C discontinues transmission (Figure 8-1).
8.3
Sequential Read
FIGURE 8-1:
CURRENT ADDRESS
READ
Sequential reads are initiated in the same way as a
random read except that after the 24C01C transmits
the first data byte, the master issues an acknowledge
as opposed to a Stop condition in a random read. This
directs the 24C01C to transmit the next sequentially
addressed 8-bit word (Figure 8-3).
S
T
A
R
T
S
T
Bus Activity
Master
Control
Data
Byte
O
P
SDA Line
P
S
To provide sequential reads the 24C01C contains an
internal Address Pointer which is incremented by one
at the completion of each operation. This Address
Pointer allows the entire memory contents to be serially
read during one operation. The internal Address
Pointer will automatically roll over from address 7F to
address 00.
A
C
K
N
O
Bus Activity
A
C
K
FIGURE 8-2:
RANDOM READ
S
T
S
T
A
R
T
S
T
O
P
Bus Activity
Master
Control
Byte
Word
Address (n)
Control
Byte
A
R
T
Data (n)
S
P
S
SDA Line
A
C
K
A
C
K
A
C
K
N
O
Bus Activity
A
C
K
FIGURE 8-3:
SEQUENTIAL READ
S
T
O
P
Bus Activity
Master
Control
Data n
Byte
Data n + 1
Data n + 2
Data n + X
P
SDA Line
A
C
K
A
C
K
A
C
K
A
C
K
N
O
A
C
K
Bus Activity
1997-2012 Microchip Technology Inc.
DS21201K-page 11
24C01C
9.0
9.1
PACKAGING INFORMATION
Package Marking Information
8-Lead PDIP (300 mil)
Example:
24C01C
XXXXXXXX
T/XXXNNN
I/P
13F
e
3
YYWW
0527
8-Lead SOIC (3.90 mm)
Example:
24C01CI
XXXXXXXT
e
3
XXXXYYWW
SN
0527
NNN
13F
Example:
Example:
8-Lead TSSOP
4C1C
I527
13F
XXXX
TYWW
NNN
8-Lead MSOP
XXXXT
4C1CI
YWWNNN
52713F
8-Lead 2x3 DFN
Example:
XXX
YWW
NN
2N7
527
13
8-Lead 2x3 TDFN
Example:
XXX
YWW
NN
AN7
527
13
DS21201K-page 12
1997-2012 Microchip Technology Inc.
24C01C
1st Line Marking Codes
DFN TDFN
Part Number
SOT-23
TSSOP
MSOP
I Temp.
E Temp.
I Temp.
E Temp.
I Temp.
HANN
E Temp.
24C01C
4C1C
4C1CT
2N7
2N8
AN7
AN8
HBNN
Note:
T = Temperature grade (I, E)
Example:
HAEC
6-Lead SOT-23
XXNN
Legend: XX...X Part number or part number code
T
Temperature (I, E)
Y
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code (2 characters for small packages)
Pb-free JEDEC designator for Matte Tin (Sn)
YY
WW
NNN
e
3
Note: For very small packages with no room for the Pb-free JEDEC designator
e
3
, the marking will only appear on the outer carton or reel label.
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
Note:
Please visit www.microchip.com/Pbfree for the latest information on Pb-free conversion.
*Standard OTP marking consists of Microchip part number, year code, week code, and traceability code.
1997-2012 Microchip Technology Inc.
DS21201K-page 13
24C01C
ꢀꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆꢍꢎꢄꢈꢆꢏꢐꢁꢂꢋꢐꢃꢆꢑꢇꢒꢆꢓꢆꢔꢕꢕꢆꢖꢋꢈꢆꢗꢘꢅꢙꢆꢚꢇꢍꢏꢇꢛ
ꢜꢘꢊꢃꢝ ꢬꢕꢐꢅꢏꢘꢌꢅꢑꢕꢇꢏꢅꢖꢈꢐꢐꢌꢄꢏꢅꢡꢉꢖꢭꢉꢜꢌꢅꢋꢐꢉꢗꢃꢄꢜꢇꢓꢅꢡꢊꢌꢉꢇꢌꢅꢇꢌꢌꢅꢏꢘꢌꢅꢢꢃꢖꢐꢕꢖꢘꢃꢡꢅꢂꢉꢖꢭꢉꢜꢃꢄꢜꢅꢛꢡꢌꢖꢃꢎꢃꢖꢉꢏꢃꢕꢄꢅꢊꢕꢖꢉꢏꢌꢋꢅꢉꢏꢅ
ꢘꢏꢏꢡꢪꢮꢮꢗꢗꢗꢁꢑꢃꢖꢐꢕꢖꢘꢃꢡꢁꢖꢕꢑꢮꢡꢉꢖꢭꢉꢜꢃꢄꢜ
N
NOTE 1
E1
3
1
2
D
E
A2
A
L
A1
c
e
eB
b1
b
ꢯꢄꢃꢏꢇ
ꢰꢱꢝꢲꢠꢛ
ꢟꢃꢑꢌꢄꢇꢃꢕꢄꢅꢳꢃꢑꢃꢏꢇ
ꢢꢰꢱ
ꢱꢴꢢ
ꢶ
ꢁꢀꢣꢣꢅꢩꢛꢝ
ꢷ
ꢁꢀꢞꢣ
ꢷ
ꢁꢞꢀꢣ
ꢁꢙꢨꢣ
ꢁꢞꢺꢨ
ꢁꢀꢞꢣ
ꢁꢣꢀꢣ
ꢁꢣꢺꢣ
ꢁꢣꢀꢶ
ꢷ
ꢢꢦꢵ
ꢱꢈꢑꢔꢌꢐꢅꢕꢎꢅꢂꢃꢄꢇ
ꢂꢃꢏꢖꢘ
ꢫꢕꢡꢅꢏꢕꢅꢛꢌꢉꢏꢃꢄꢜꢅꢂꢊꢉꢄꢌ
ꢢꢕꢊꢋꢌꢋꢅꢂꢉꢖꢭꢉꢜꢌꢅꢫꢘꢃꢖꢭꢄꢌꢇꢇ
ꢩꢉꢇꢌꢅꢏꢕꢅꢛꢌꢉꢏꢃꢄꢜꢅꢂꢊꢉꢄꢌ
ꢛꢘꢕꢈꢊꢋꢌꢐꢅꢏꢕꢅꢛꢘꢕꢈꢊꢋꢌꢐꢅꢹꢃꢋꢏꢘ
ꢢꢕꢊꢋꢌꢋꢅꢂꢉꢖꢭꢉꢜꢌꢅꢹꢃꢋꢏꢘ
ꢴꢆꢌꢐꢉꢊꢊꢅꢳꢌꢄꢜꢏꢘ
ꢱ
ꢌ
ꢦ
ꢦꢙ
ꢦꢀ
ꢠ
ꢠꢀ
ꢟ
ꢳ
ꢖ
ꢔꢀ
ꢔ
ꢌꢩ
ꢷ
ꢁꢙꢀꢣ
ꢁꢀꢸꢨ
ꢷ
ꢁꢀꢀꢨ
ꢁꢣꢀꢨ
ꢁꢙꢸꢣ
ꢁꢙꢥꢣ
ꢁꢞꢥꢶ
ꢁꢀꢀꢨ
ꢁꢣꢣꢶ
ꢁꢣꢥꢣ
ꢁꢣꢀꢥ
ꢷ
ꢁꢞꢙꢨ
ꢁꢙꢶꢣ
ꢁꢥꢣꢣ
ꢁꢀꢨꢣ
ꢁꢣꢀꢨ
ꢁꢣꢻꢣ
ꢁꢣꢙꢙ
ꢁꢥꢞꢣ
ꢫꢃꢡꢅꢏꢕꢅꢛꢌꢉꢏꢃꢄꢜꢅꢂꢊꢉꢄꢌ
ꢳꢌꢉꢋꢅꢫꢘꢃꢖꢭꢄꢌꢇꢇ
ꢯꢡꢡꢌꢐꢅꢳꢌꢉꢋꢅꢹꢃꢋꢏꢘ
ꢳꢕꢗꢌꢐꢅꢳꢌꢉꢋꢅꢹꢃꢋꢏꢘ
ꢴꢆꢌꢐꢉꢊꢊꢅꢼꢕꢗꢅꢛꢡꢉꢖꢃꢄꢜꢅꢅꢚ
ꢜꢘꢊꢃꢉꢝ
ꢀꢁ ꢂꢃꢄꢅꢀꢅꢆꢃꢇꢈꢉꢊꢅꢃꢄꢋꢌꢍꢅꢎꢌꢉꢏꢈꢐꢌꢅꢑꢉꢒꢅꢆꢉꢐꢒꢓꢅꢔꢈꢏꢅꢑꢈꢇꢏꢅꢔꢌꢅꢊꢕꢖꢉꢏꢌꢋꢅꢗꢃꢏꢘꢅꢏꢘꢌꢅꢘꢉꢏꢖꢘꢌꢋꢅꢉꢐꢌꢉꢁ
ꢙꢁ ꢚꢅꢛꢃꢜꢄꢃꢎꢃꢖꢉꢄꢏꢅꢝꢘꢉꢐꢉꢖꢏꢌꢐꢃꢇꢏꢃꢖꢁ
ꢞꢁ ꢟꢃꢑꢌꢄꢇꢃꢕꢄꢇꢅꢟꢅꢉꢄꢋꢅꢠꢀꢅꢋꢕꢅꢄꢕꢏꢅꢃꢄꢖꢊꢈꢋꢌꢅꢑꢕꢊꢋꢅꢎꢊꢉꢇꢘꢅꢕꢐꢅꢡꢐꢕꢏꢐꢈꢇꢃꢕꢄꢇꢁꢅꢢꢕꢊꢋꢅꢎꢊꢉꢇꢘꢅꢕꢐꢅꢡꢐꢕꢏꢐꢈꢇꢃꢕꢄꢇꢅꢇꢘꢉꢊꢊꢅꢄꢕꢏꢅꢌꢍꢖꢌꢌꢋꢅꢁꢣꢀꢣꢤꢅꢡꢌꢐꢅꢇꢃꢋꢌꢁ
ꢥꢁ ꢟꢃꢑꢌꢄꢇꢃꢕꢄꢃꢄꢜꢅꢉꢄꢋꢅꢏꢕꢊꢌꢐꢉꢄꢖꢃꢄꢜꢅꢡꢌꢐꢅꢦꢛꢢꢠꢅꢧꢀꢥꢁꢨꢢꢁ
ꢩꢛꢝꢪꢅꢩꢉꢇꢃꢖꢅꢟꢃꢑꢌꢄꢇꢃꢕꢄꢁꢅꢫꢘꢌꢕꢐꢌꢏꢃꢖꢉꢊꢊꢒꢅꢌꢍꢉꢖꢏꢅꢆꢉꢊꢈꢌꢅꢇꢘꢕꢗꢄꢅꢗꢃꢏꢘꢕꢈꢏꢅꢏꢕꢊꢌꢐꢉꢄꢖꢌꢇꢁ
ꢢꢃꢖꢐꢕꢖꢘꢃꢡ ꢫꢌꢖꢘꢄꢕꢊꢕꢜꢒ ꢟꢐꢉꢗꢃꢄꢜ ꢝꢣꢥꢽꢣꢀꢶꢩ
DS21201K-page 14
1997-2012 Microchip Technology Inc.
24C01C
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
1997-2012 Microchip Technology Inc.
DS21201K-page 15
24C01C
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS21201K-page 16
1997-2012 Microchip Technology Inc.
24C01C
ꢀꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆꢞꢖꢄꢈꢈꢆꢟꢎꢊꢈꢋꢐꢃꢆꢑꢞꢜꢒꢆꢓꢆꢜꢄꢠꢠꢘꢡꢢꢆꢔꢣꢤꢕꢆꢖꢖꢆꢗꢘꢅꢙꢆꢚꢞꢟꢏꢥꢛ
ꢜꢘꢊꢃꢝ ꢬꢕꢐꢅꢏꢘꢌꢅꢑꢕꢇꢏꢅꢖꢈꢐꢐꢌꢄꢏꢅꢡꢉꢖꢭꢉꢜꢌꢅꢋꢐꢉꢗꢃꢄꢜꢇꢓꢅꢡꢊꢌꢉꢇꢌꢅꢇꢌꢌꢅꢏꢘꢌꢅꢢꢃꢖꢐꢕꢖꢘꢃꢡꢅꢂꢉꢖꢭꢉꢜꢃꢄꢜꢅꢛꢡꢌꢖꢃꢎꢃꢖꢉꢏꢃꢕꢄꢅꢊꢕꢖꢉꢏꢌꢋꢅꢉꢏꢅ
ꢘꢏꢏꢡꢪꢮꢮꢗꢗꢗꢁꢑꢃꢖꢐꢕꢖꢘꢃꢡꢁꢖꢕꢑꢮꢡꢉꢖꢭꢉꢜꢃꢄꢜ
1997-2012 Microchip Technology Inc.
DS21201K-page 17
24C01C
ꢀꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆꢦꢧꢋꢐꢆꢞꢧꢠꢋꢐꢨꢆꢞꢖꢄꢈꢈꢆꢟꢎꢊꢈꢋꢐꢃꢆꢑꢞꢦꢒꢆꢓꢆꢩꢣꢩꢆꢖꢖꢆꢗꢘꢅꢙꢆꢚꢦꢞꢞꢟꢇꢛ
ꢜꢘꢊꢃꢝ ꢬꢕꢐꢅꢏꢘꢌꢅꢑꢕꢇꢏꢅꢖꢈꢐꢐꢌꢄꢏꢅꢡꢉꢖꢭꢉꢜꢌꢅꢋꢐꢉꢗꢃꢄꢜꢇꢓꢅꢡꢊꢌꢉꢇꢌꢅꢇꢌꢌꢅꢏꢘꢌꢅꢢꢃꢖꢐꢕꢖꢘꢃꢡꢅꢂꢉꢖꢭꢉꢜꢃꢄꢜꢅꢛꢡꢌꢖꢃꢎꢃꢖꢉꢏꢃꢕꢄꢅꢊꢕꢖꢉꢏꢌꢋꢅꢉꢏꢅ
ꢘꢏꢏꢡꢪꢮꢮꢗꢗꢗꢁꢑꢃꢖꢐꢕꢖꢘꢃꢡꢁꢖꢕꢑꢮꢡꢉꢖꢭꢉꢜꢃꢄꢜ
D
N
E
E1
NOTE 1
1
2
b
e
c
φ
A
A2
A1
L
L1
ꢯꢄꢃꢏꢇ
ꢢꢰꢳꢳꢰꢢꢠꢫꢠꢼꢛ
ꢟꢃꢑꢌꢄꢇꢃꢕꢄꢅꢳꢃꢑꢃꢏꢇ
ꢢꢰꢱ
ꢱꢴꢢ
ꢢꢦꢵ
ꢱꢈꢑꢔꢌꢐꢅꢕꢎꢅꢂꢃꢄꢇ
ꢂꢃꢏꢖꢘ
ꢱ
ꢌ
ꢶ
ꢣꢁꢺꢨꢅꢩꢛꢝ
ꢴꢆꢌꢐꢉꢊꢊꢅꢲꢌꢃꢜꢘꢏ
ꢢꢕꢊꢋꢌꢋꢅꢂꢉꢖꢭꢉꢜꢌꢅꢫꢘꢃꢖꢭꢄꢌꢇꢇ
ꢛꢏꢉꢄꢋꢕꢎꢎꢅ
ꢦ
ꢷ
ꢣꢁꢶꢣ
ꢣꢁꢣꢨ
ꢷ
ꢀꢁꢣꢣ
ꢷ
ꢀꢁꢙꢣ
ꢀꢁꢣꢨ
ꢣꢁꢀꢨ
ꢦꢙ
ꢦꢀ
ꢠ
ꢴꢆꢌꢐꢉꢊꢊꢅꢹꢃꢋꢏꢘ
ꢺꢁꢥꢣꢅꢩꢛꢝ
ꢢꢕꢊꢋꢌꢋꢅꢂꢉꢖꢭꢉꢜꢌꢅꢹꢃꢋꢏꢘ
ꢢꢕꢊꢋꢌꢋꢅꢂꢉꢖꢭꢉꢜꢌꢅꢳꢌꢄꢜꢏꢘ
ꢬꢕꢕꢏꢅꢳꢌꢄꢜꢏꢘ
ꢠꢀ
ꢟ
ꢳ
ꢥꢁꢞꢣ
ꢙꢁꢸꢣ
ꢣꢁꢥꢨ
ꢥꢁꢥꢣ
ꢞꢁꢣꢣ
ꢣꢁꢺꢣ
ꢥꢁꢨꢣ
ꢞꢁꢀꢣ
ꢣꢁꢻꢨ
ꢬꢕꢕꢏꢡꢐꢃꢄꢏ
ꢬꢕꢕꢏꢅꢦꢄꢜꢊꢌ
ꢳꢌꢉꢋꢅꢫꢘꢃꢖꢭꢄꢌꢇꢇ
ꢳꢌꢉꢋꢅꢹꢃꢋꢏꢘ
ꢳꢀ
ꢀ
ꢀꢁꢣꢣꢅꢼꢠꢬ
ꢣꢾ
ꢣꢁꢣꢸ
ꢣꢁꢀꢸ
ꢷ
ꢷ
ꢷ
ꢶꢾ
ꢖ
ꢔ
ꢣꢁꢙꢣ
ꢣꢁꢞꢣ
ꢜꢘꢊꢃꢉꢝ
ꢀꢁ ꢂꢃꢄꢅꢀꢅꢆꢃꢇꢈꢉꢊꢅꢃꢄꢋꢌꢍꢅꢎꢌꢉꢏꢈꢐꢌꢅꢑꢉꢒꢅꢆꢉꢐꢒꢓꢅꢔꢈꢏꢅꢑꢈꢇꢏꢅꢔꢌꢅꢊꢕꢖꢉꢏꢌꢋꢅꢗꢃꢏꢘꢃꢄꢅꢏꢘꢌꢅꢘꢉꢏꢖꢘꢌꢋꢅꢉꢐꢌꢉꢁ
ꢙꢁ ꢟꢃꢑꢌꢄꢇꢃꢕꢄꢇꢅꢟꢅꢉꢄꢋꢅꢠꢀꢅꢋꢕꢅꢄꢕꢏꢅꢃꢄꢖꢊꢈꢋꢌꢅꢑꢕꢊꢋꢅꢎꢊꢉꢇꢘꢅꢕꢐꢅꢡꢐꢕꢏꢐꢈꢇꢃꢕꢄꢇꢁꢅꢢꢕꢊꢋꢅꢎꢊꢉꢇꢘꢅꢕꢐꢅꢡꢐꢕꢏꢐꢈꢇꢃꢕꢄꢇꢅꢇꢘꢉꢊꢊꢅꢄꢕꢏꢅꢌꢍꢖꢌꢌꢋꢅꢣꢁꢀꢨꢅꢑꢑꢅꢡꢌꢐꢅꢇꢃꢋꢌꢁ
ꢞꢁ ꢟꢃꢑꢌꢄꢇꢃꢕꢄꢃꢄꢜꢅꢉꢄꢋꢅꢏꢕꢊꢌꢐꢉꢄꢖꢃꢄꢜꢅꢡꢌꢐꢅꢦꢛꢢꢠꢅꢧꢀꢥꢁꢨꢢꢁ
ꢩꢛꢝꢪ ꢩꢉꢇꢃꢖꢅꢟꢃꢑꢌꢄꢇꢃꢕꢄꢁꢅꢫꢘꢌꢕꢐꢌꢏꢃꢖꢉꢊꢊꢒꢅꢌꢍꢉꢖꢏꢅꢆꢉꢊꢈꢌꢅꢇꢘꢕꢗꢄꢅꢗꢃꢏꢘꢕꢈꢏꢅꢏꢕꢊꢌꢐꢉꢄꢖꢌꢇꢁ
ꢼꢠꢬꢪ ꢼꢌꢎꢌꢐꢌꢄꢖꢌꢅꢟꢃꢑꢌꢄꢇꢃꢕꢄꢓꢅꢈꢇꢈꢉꢊꢊꢒꢅꢗꢃꢏꢘꢕꢈꢏꢅꢏꢕꢊꢌꢐꢉꢄꢖꢌꢓꢅꢎꢕꢐꢅꢃꢄꢎꢕꢐꢑꢉꢏꢃꢕꢄꢅꢡꢈꢐꢡꢕꢇꢌꢇꢅꢕꢄꢊꢒꢁ
ꢢꢃꢖꢐꢕꢖꢘꢃꢡ ꢫꢌꢖꢘꢄꢕꢊꢕꢜꢒ ꢟꢐꢉꢗꢃꢄꢜ ꢝꢣꢥꢽꢣꢶꢺꢩ
DS21201K-page 18
1997-2012 Microchip Technology Inc.
24C01C
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
1997-2012 Microchip Technology Inc.
DS21201K-page 19
24C01C
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS21201K-page 20
1997-2012 Microchip Technology Inc.
24C01C
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
1997-2012 Microchip Technology Inc.
DS21201K-page 21
24C01C
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS21201K-page 22
1997-2012 Microchip Technology Inc.
24C01C
ꢀꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆꢍꢎꢄꢈꢆꢪꢈꢄꢊꢢꢆꢜꢘꢆꢂꢃꢄꢅꢆꢇꢄꢌꢨꢄꢫꢃꢆꢑꢬꢥꢒꢆꢓꢆꢭꢮꢔꢮꢕꢣꢤꢆꢖꢖꢆꢗꢘꢅꢙꢆꢚꢍꢪꢜꢛ
ꢜꢘꢊꢃꢝ ꢬꢕꢐꢅꢏꢘꢌꢅꢑꢕꢇꢏꢅꢖꢈꢐꢐꢌꢄꢏꢅꢡꢉꢖꢭꢉꢜꢌꢅꢋꢐꢉꢗꢃꢄꢜꢇꢓꢅꢡꢊꢌꢉꢇꢌꢅꢇꢌꢌꢅꢏꢘꢌꢅꢢꢃꢖꢐꢕꢖꢘꢃꢡꢅꢂꢉꢖꢭꢉꢜꢃꢄꢜꢅꢛꢡꢌꢖꢃꢎꢃꢖꢉꢏꢃꢕꢄꢅꢊꢕꢖꢉꢏꢌꢋꢅꢉꢏꢅ
ꢘꢏꢏꢡꢪꢮꢮꢗꢗꢗꢁꢑꢃꢖꢐꢕꢖꢘꢃꢡꢁꢖꢕꢑꢮꢡꢉꢖꢭꢉꢜꢃꢄꢜ
e
D
b
N
N
L
K
E2
E
EXPOSED PAD
NOTE 1
NOTE 1
2
1
1
2
D2
BOTTOM VIEW
TOP VIEW
A
NOTE 2
A3
A1
ꢯꢄꢃꢏꢇ
ꢢꢰꢳꢳꢰꢢꢠꢫꢠꢼꢛ
ꢟꢃꢑꢌꢄꢇꢃꢕꢄꢅꢳꢃꢑꢃꢏꢇ
ꢢꢰꢱ
ꢱꢴꢢ
ꢶ
ꢣꢁꢨꢣꢅꢩꢛꢝ
ꢣꢁꢸꢣ
ꢢꢦꢵ
ꢱꢈꢑꢔꢌꢐꢅꢕꢎꢅꢂꢃꢄꢇ
ꢂꢃꢏꢖꢘ
ꢴꢆꢌꢐꢉꢊꢊꢅꢲꢌꢃꢜꢘꢏ
ꢛꢏꢉꢄꢋꢕꢎꢎꢅ
ꢝꢕꢄꢏꢉꢖꢏꢅꢫꢘꢃꢖꢭꢄꢌꢇꢇ
ꢴꢆꢌꢐꢉꢊꢊꢅꢳꢌꢄꢜꢏꢘ
ꢴꢆꢌꢐꢉꢊꢊꢅꢹꢃꢋꢏꢘ
ꢱ
ꢌ
ꢦ
ꢦꢀ
ꢦꢞ
ꢟ
ꢣꢁꢶꢣ
ꢣꢁꢣꢣ
ꢀꢁꢣꢣ
ꢣꢁꢣꢨ
ꢣꢁꢣꢙ
ꢣꢁꢙꢣꢅꢼꢠꢬ
ꢙꢁꢣꢣꢅꢩꢛꢝ
ꢞꢁꢣꢣꢅꢩꢛꢝ
ꢷ
ꢷ
ꢣꢁꢙꢨ
ꢠ
ꢠꢍꢡꢕꢇꢌꢋꢅꢂꢉꢋꢅꢳꢌꢄꢜꢏꢘ
ꢠꢍꢡꢕꢇꢌꢋꢅꢂꢉꢋꢅꢹꢃꢋꢏꢘ
ꢝꢕꢄꢏꢉꢖꢏꢅꢹꢃꢋꢏꢘ
ꢝꢕꢄꢏꢉꢖꢏꢅꢳꢌꢄꢜꢏꢘ
ꢝꢕꢄꢏꢉꢖꢏꢽꢏꢕꢽꢠꢍꢡꢕꢇꢌꢋꢅꢂꢉꢋ
ꢟꢙ
ꢠꢙ
ꢔ
ꢳ
U
ꢀꢁꢞꢣ
ꢀꢁꢨꢣ
ꢣꢁꢙꢣ
ꢣꢁꢞꢣ
ꢣꢁꢙꢣ
ꢀꢁꢨꢨ
ꢀꢁꢻꢨ
ꢣꢁꢞꢣ
ꢣꢁꢨꢣ
ꢷ
ꢣꢁꢥꢣ
ꢷ
ꢜꢘꢊꢃꢉꢝ
ꢀꢁ ꢂꢃꢄꢅꢀꢅꢆꢃꢇꢈꢉꢊꢅꢃꢄꢋꢌꢍꢅꢎꢌꢉꢏꢈꢐꢌꢅꢑꢉꢒꢅꢆꢉꢐꢒꢓꢅꢔꢈꢏꢅꢑꢈꢇꢏꢅꢔꢌꢅꢊꢕꢖꢉꢏꢌꢋꢅꢗꢃꢏꢘꢃꢄꢅꢏꢘꢌꢅꢘꢉꢏꢖꢘꢌꢋꢅꢉꢐꢌꢉꢁ
ꢙꢁ ꢂꢉꢖꢭꢉꢜꢌꢅꢑꢉꢒꢅꢘꢉꢆꢌꢅꢕꢄꢌꢅꢕꢐꢅꢑꢕꢐꢌꢅꢌꢍꢡꢕꢇꢌꢋꢅꢏꢃꢌꢅꢔꢉꢐꢇꢅꢉꢏꢅꢌꢄꢋꢇꢁ
ꢞꢁ ꢂꢉꢖꢭꢉꢜꢌꢅꢃꢇꢅꢇꢉꢗꢅꢇꢃꢄꢜꢈꢊꢉꢏꢌꢋꢁ
ꢥꢁ ꢟꢃꢑꢌꢄꢇꢃꢕꢄꢃꢄꢜꢅꢉꢄꢋꢅꢏꢕꢊꢌꢐꢉꢄꢖꢃꢄꢜꢅꢡꢌꢐꢅꢦꢛꢢꢠꢅꢧꢀꢥꢁꢨꢢꢁ
ꢩꢛꢝꢪ ꢩꢉꢇꢃꢖꢅꢟꢃꢑꢌꢄꢇꢃꢕꢄꢁꢅꢫꢘꢌꢕꢐꢌꢏꢃꢖꢉꢊꢊꢒꢅꢌꢍꢉꢖꢏꢅꢆꢉꢊꢈꢌꢅꢇꢘꢕꢗꢄꢅꢗꢃꢏꢘꢕꢈꢏꢅꢏꢕꢊꢌꢐꢉꢄꢖꢌꢇꢁ
ꢼꢠꢬꢪ ꢼꢌꢎꢌꢐꢌꢄꢖꢌꢅꢟꢃꢑꢌꢄꢇꢃꢕꢄꢓꢅꢈꢇꢈꢉꢊꢊꢒꢅꢗꢃꢏꢘꢕꢈꢏꢅꢏꢕꢊꢌꢐꢉꢄꢖꢌꢓꢅꢎꢕꢐꢅꢃꢄꢎꢕꢐꢑꢉꢏꢃꢕꢄꢅꢡꢈꢐꢡꢕꢇꢌꢇꢅꢕꢄꢊꢒꢁ
ꢢꢃꢖꢐꢕꢖꢘꢃꢡ ꢫꢌꢖꢘꢄꢕꢊꢕꢜꢒ ꢟꢐꢉꢗꢃꢄꢜ ꢝꢣꢥꢽꢀꢙꢞꢝ
1997-2012 Microchip Technology Inc.
DS21201K-page 23
24C01C
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS21201K-page 24
1997-2012 Microchip Technology Inc.
24C01C
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
1997-2012 Microchip Technology Inc.
DS21201K-page 25
24C01C
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS21201K-page 26
1997-2012 Microchip Technology Inc.
24C01C
ꢀꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆꢍꢎꢄꢈꢆꢪꢈꢄꢊꢢꢆꢜꢘꢆꢂꢃꢄꢅꢆꢇꢄꢌꢨꢄꢫꢃꢆꢑꢬꢜꢒꢆꢓꢆꢭꢮꢔꢮꢕꢣꢯꢰꢆꢖꢖꢆꢗꢘꢅꢙꢆꢚꢦꢍꢪꢜꢛ
ꢜꢘꢊꢃꢝ ꢬꢕꢐꢅꢏꢘꢌꢅꢑꢕꢇꢏꢅꢖꢈꢐꢐꢌꢄꢏꢅꢡꢉꢖꢭꢉꢜꢌꢅꢋꢐꢉꢗꢃꢄꢜꢇꢓꢅꢡꢊꢌꢉꢇꢌꢅꢇꢌꢌꢅꢏꢘꢌꢅꢢꢃꢖꢐꢕꢖꢘꢃꢡꢅꢂꢉꢖꢭꢉꢜꢃꢄꢜꢅꢛꢡꢌꢖꢃꢎꢃꢖꢉꢏꢃꢕꢄꢅꢊꢕꢖꢉꢏꢌꢋꢅꢉꢏꢅ
ꢘꢏꢏꢡꢪꢮꢮꢗꢗꢗꢁꢑꢃꢖꢐꢕꢖꢘꢃꢡꢁꢖꢕꢑꢮꢡꢉꢖꢭꢉꢜꢃꢄꢜ
1997-2012 Microchip Technology Inc.
DS21201K-page 27
24C01C
ꢱꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆꢞꢖꢄꢈꢈꢆꢟꢎꢊꢈꢋꢐꢃꢆꢦꢠꢄꢐꢉꢋꢉꢊꢘꢠꢆꢑꢟꢦꢒꢆꢚꢞꢟꢦꢁꢭꢔꢛ
ꢜꢘꢊꢃꢝ ꢬꢕꢐꢅꢏꢘꢌꢅꢑꢕꢇꢏꢅꢖꢈꢐꢐꢌꢄꢏꢅꢡꢉꢖꢭꢉꢜꢌꢅꢋꢐꢉꢗꢃꢄꢜꢇꢓꢅꢡꢊꢌꢉꢇꢌꢅꢇꢌꢌꢅꢏꢘꢌꢅꢢꢃꢖꢐꢕꢖꢘꢃꢡꢅꢂꢉꢖꢭꢉꢜꢃꢄꢜꢅꢛꢡꢌꢖꢃꢎꢃꢖꢉꢏꢃꢕꢄꢅꢊꢕꢖꢉꢏꢌꢋꢅꢉꢏꢅ
ꢘꢏꢏꢡꢪꢮꢮꢗꢗꢗꢁꢑꢃꢖꢐꢕꢖꢘꢃꢡꢁꢖꢕꢑꢮꢡꢉꢖꢭꢉꢜꢃꢄꢜ
b
4
N
E
E1
PIN 1 ID BY
LASER MARK
1
2
3
e
e1
D
c
A
φ
A2
L
A1
L1
ꢯꢄꢃꢏꢇ
ꢢꢰꢳꢳꢰꢢꢠꢫꢠꢼꢛ
ꢟꢃꢑꢌꢄꢇꢃꢕꢄꢅꢳꢃꢑꢃꢏꢇ
ꢢꢰꢱ
ꢱꢴꢢ
ꢢꢦꢵ
ꢱꢈꢑꢔꢌꢐꢅꢕꢎꢅꢂꢃꢄꢇ
ꢂꢃꢏꢖꢘ
ꢱ
ꢌ
ꢺ
ꢣꢁꢸꢨꢅꢩꢛꢝ
ꢴꢈꢏꢇꢃꢋꢌꢅꢳꢌꢉꢋꢅꢂꢃꢏꢖꢘ
ꢴꢆꢌꢐꢉꢊꢊꢅꢲꢌꢃꢜꢘꢏ
ꢢꢕꢊꢋꢌꢋꢅꢂꢉꢖꢭꢉꢜꢌꢅꢫꢘꢃꢖꢭꢄꢌꢇꢇ
ꢛꢏꢉꢄꢋꢕꢎꢎ
ꢴꢆꢌꢐꢉꢊꢊꢅꢹꢃꢋꢏꢘ
ꢢꢕꢊꢋꢌꢋꢅꢂꢉꢖꢭꢉꢜꢌꢅꢹꢃꢋꢏꢘ
ꢴꢆꢌꢐꢉꢊꢊꢅꢳꢌꢄꢜꢏꢘ
ꢬꢕꢕꢏꢅꢳꢌꢄꢜꢏꢘ
ꢬꢕꢕꢏꢡꢐꢃꢄꢏ
ꢬꢕꢕꢏꢅꢦꢄꢜꢊꢌ
ꢳꢌꢉꢋꢅꢫꢘꢃꢖꢭꢄꢌꢇꢇ
ꢳꢌꢉꢋꢅꢹꢃꢋꢏꢘ
ꢌꢀ
ꢦ
ꢦꢙ
ꢦꢀ
ꢠ
ꢠꢀ
ꢟ
ꢳ
ꢀꢁꢸꢣꢅꢩꢛꢝ
ꢣꢁꢸꢣ
ꢣꢁꢶꢸ
ꢣꢁꢣꢣ
ꢙꢁꢙꢣ
ꢀꢁꢞꢣ
ꢙꢁꢻꢣ
ꢣꢁꢀꢣ
ꢣꢁꢞꢨ
ꢣꢾ
ꢷ
ꢷ
ꢷ
ꢷ
ꢷ
ꢷ
ꢷ
ꢷ
ꢷ
ꢷ
ꢷ
ꢀꢁꢥꢨ
ꢀꢁꢞꢣ
ꢣꢁꢀꢨ
ꢞꢁꢙꢣ
ꢀꢁꢶꢣ
ꢞꢁꢀꢣ
ꢣꢁꢺꢣ
ꢣꢁꢶꢣ
ꢞꢣꢾ
ꢳꢀ
ꢀ
ꢖ
ꢔ
ꢣꢁꢣꢶ
ꢣꢁꢙꢣ
ꢣꢁꢙꢺ
ꢣꢁꢨꢀ
ꢜꢘꢊꢃꢉꢝ
ꢀꢁ ꢟꢃꢑꢌꢄꢇꢃꢕꢄꢇꢅꢟꢅꢉꢄꢋꢅꢠꢀꢅꢋꢕꢅꢄꢕꢏꢅꢃꢄꢖꢊꢈꢋꢌꢅꢑꢕꢊꢋꢅꢎꢊꢉꢇꢘꢅꢕꢐꢅꢡꢐꢕꢏꢐꢈꢇꢃꢕꢄꢇꢁꢅꢢꢕꢊꢋꢅꢎꢊꢉꢇꢘꢅꢕꢐꢅꢡꢐꢕꢏꢐꢈꢇꢃꢕꢄꢇꢅꢇꢘꢉꢊꢊꢅꢄꢕꢏꢅꢌꢍꢖꢌꢌꢋꢅꢣꢁꢀꢙꢻꢅꢑꢑꢅꢡꢌꢐꢅꢇꢃꢋꢌꢁ
ꢙꢁ ꢟꢃꢑꢌꢄꢇꢃꢕꢄꢃꢄꢜꢅꢉꢄꢋꢅꢏꢕꢊꢌꢐꢉꢄꢖꢃꢄꢜꢅꢡꢌꢐꢅꢦꢛꢢꢠꢅꢧꢀꢥꢁꢨꢢꢁ
ꢩꢛꢝꢪ ꢩꢉꢇꢃꢖꢅꢟꢃꢑꢌꢄꢇꢃꢕꢄꢁꢅꢫꢘꢌꢕꢐꢌꢏꢃꢖꢉꢊꢊꢒꢅꢌꢍꢉꢖꢏꢅꢆꢉꢊꢈꢌꢅꢇꢘꢕꢗꢄꢅꢗꢃꢏꢘꢕꢈꢏꢅꢏꢕꢊꢌꢐꢉꢄꢖꢌꢇꢁ
ꢢꢃꢖꢐꢕꢖꢘꢃꢡ ꢫꢌꢖꢘꢄꢕꢊꢕꢜꢒ ꢟꢐꢉꢗꢃꢄꢜ ꢝꢣꢥꢽꢣꢙꢶꢩ
DS21201K-page 28
1997-2012 Microchip Technology Inc.
24C01C
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
1997-2012 Microchip Technology Inc.
DS21201K-page 29
24C01C
APPENDIX A: REVISION HISTORY
Revision A (06/1997)
Initial release.
Revision B (07/1998)
Revision C (08/1999)
Revision D (12/2003)
Corrections to Section 1.0, Electrical Characteristics.
Revision E (04/2005)
Added DFN package.
Revision F (01/2007)
Revised Features Section; Deleted Commercial Temp;
Replaced Package Drawings; Replaced On-Line
Support page; Revised Product ID System.
Revision G (03/2007)
Replaced Package Drawings (Rev. AM).
Revision H (04/2008)
Replaced Package Drawings; Added TDFN package;
Revised Product ID section.
Revision J (08/2008)
Updated Features Section; Added Table 2-1 Pin
Function Table; Corrections to Table 1-1, DC Charac-
teristics; Updated Table 1-2, AC Characteristics;
Updated Package Drawings.
Revision K (03/2012)
Add 6-Lead SOT-23 Package
DS21201K-page 30
1997-2012 Microchip Technology Inc.
24C01C
THE MICROCHIP WEB SITE
CUSTOMER SUPPORT
Microchip provides online support via our WWW site at
www.microchip.com. This web site is used as a means
to make files and information easily available to
customers. Accessible by using your favorite Internet
browser, the web site contains the following
information:
Users of Microchip products can receive assistance
through several channels:
• Distributor or Representative
• Local Sales Office
• Field Application Engineer (FAE)
• Technical Support
• Product Support – Data sheets and errata,
application notes and sample programs, design
resources, user’s guides and hardware support
documents, latest software releases and archived
software
• Development Systems Information Line
Customers
should
contact
their
distributor,
representative or field application engineer (FAE) for
support. Local sales offices are also available to help
customers. A listing of sales offices and locations is
included in the back of this document.
• General Technical Support – Frequently Asked
Questions (FAQ), technical support requests,
online discussion groups, Microchip consultant
program member listing
Technical support is available through the web site
at: http://microchip.com/support
• Business of Microchip – Product selector and
ordering guides, latest Microchip press releases,
listing of seminars and events, listings of
Microchip sales offices, distributors and factory
representatives
CUSTOMER CHANGE NOTIFICATION
SERVICE
Microchip’s customer notification service helps keep
customers current on Microchip products. Subscribers
will receive e-mail notification whenever there are
changes, updates, revisions or errata related to a
specified product family or development tool of interest.
To register, access the Microchip web site at
www.microchip.com. Under “Support”, click on
“Customer Change Notification” and follow the
registration instructions.
1997-2012 Microchip Technology Inc.
DS21201K-page 31
24C01C
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip
product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our
documentation can better serve you, please FAX your comments to the Technical Publications Manager at
(480) 792-4150.
Please list the following information, and use this outline to provide us with your comments about this document.
TO:
RE:
Technical Publications Manager
Reader Response
Total Pages Sent ________
From:
Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
FAX: (______) _________ - _________
Literature Number: DS21201K
Application (optional):
Would you like a reply?
Y
N
Device: 24C01C
Questions:
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
5. What deletions from the document could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
DS21201K-page 32
1997-2012 Microchip Technology Inc.
24C01C
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
Device
X
/XX
Examples:
Temperature
Range
Package
a) 24C01C-I/P: Industrial Temperature,
PDIP Package
b) 24C01C-E/SN: Extended Temperature,
SOIC Package
2
Device:
24C01C: 1K I C Serial EEPROM
c) 24C01C-I/MNY: Industrial Temperature,
2x3 TDFN Package
2
24C01CT:1K I C Serial EEPROM (Tape and Reel)
Temperature
Range:
I
E
= -40C to +85C
= -40C to +125C
Package:
P
= Plastic DIP (300 mil body), 8-lead
SN
ST
OT
MS
MC
= Plastic SOIC, (3.90 mm body), 8-lead
= Plastic TSSOP (4.4 mm body), 8-lead
= Plastic SOT-23, 6-lead (Tape and Reel only)
= Plastic MSOP (Micro Small Outline), 8-lead
= Plastic DFN (2x3x0.90 mm body), 8-lead
(1)
MNY = Plastic TDFN (2x7x0.75 mm body), 8-lead
Note 1: “Y” indicates a Nickel, Palladium, Gold (NiPdAu) finish.
1997-2012 Microchip Technology Inc.
DS21201K-page 33
24C01C
NOTES:
DS21201K-page 34
1997-2012 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART,
32
PIC logo, rfPIC and UNI/O are registered trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,
MXDEV, MXLAB, SEEVAL and The Embedded Control
Solutions Company are registered trademarks of Microchip
Technology Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, chipKIT,
chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net,
dsPICworks, dsSPEAK, ECAN, ECONOMONITOR,
FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP,
Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB,
MPLINK, mTouch, Omniscient Code Generation, PICC,
PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE,
rfLAB, Select Mode, Total Endurance, TSHARC,
UniWinDriver, WiperLock and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 1997-2012, Microchip Technology Incorporated, Printed in
the U.S.A., All Rights Reserved.
Printed on recycled paper.
ISBN: 9781620761632
QUALITY MANAGEMENT SYSTEM
CERTIFIED BY DNV
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
== ISO/TS 16949 ==
1997-2012 Microchip Technology Inc.
DS21201K-page 35
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
Web Address:
www.microchip.com
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Japan - Osaka
Tel: 81-66-152-7160
Fax: 81-66-152-9310
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Korea - Seoul
China - Hangzhou
Tel: 86-571-2819-3187
Fax: 86-571-2819-3189
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
Los Angeles
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-330-9305
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
Toronto
Mississauga, Ontario,
Canada
China - Xiamen
Tel: 905-673-0699
Fax: 905-673-6509
Tel: 86-592-2388138
Fax: 86-592-2388130
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
11/29/11
DS21201K-page 36
1997-2012 Microchip Technology Inc.
相关型号:
24C01CT-E/SNG
128 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8, 3.90 MM, ROHS COMPLIANT, PLASTIC, SOIC-8
MICROCHIP
24C01CT-I/MNY
128 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8, 2 X 3 MM, 0.75 MM HEIGHT, ROHS COMPLIANT, PLASTIC, TDFN-8
MICROCHIP
©2020 ICPDF网 联系我们和版权申明