MAXREFDES115A [MAXIM]
ISOLATED 24V TO 5V 20W POWER SUPPLY;
| 型号： | MAXREFDES115A |
| 厂家： | 
MAXIM INTEGRATED PRODUCTS |
| 描述： | ISOLATED 24V TO 5V 20W POWER SUPPLY |
| 文件： | 总16页 (文件大小：567K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
System Board 5858
MAXREFDES115#: ISOLATED 24V TO 5V 20W POWER
SUPPLY
Maxim’s power supply experts have designed and built a series of isolated, industrial
power supply reference designs. Each of these power supplies efficiently converts 24V
into useful voltage rails at a variety of power levels. Every power rail is isolated with a
readily available transformer from multiple, global vendors, providing for quick, convenient
transformer selection. Each design has been tested for load and line regulation, as well as
efficiency and transient performance.
MAXREFDES115# is an efficient active clamp topology design with 24V input, and a 5V at
4A (20W) of power. The design features the MAX17599, an active clamp, current-mode
PWM controller optimized for industrial supplies; this entire circuit fits on a 20mm x 55mm
board. As with all Maxim reference designs, the BOM, schematics, layout files, Gerber files
are all available. In addition, all boards feature through-hole pins for immediate board
placement and accelerated prototyping, and are available for purchase.
Features
• Functional Insulation
• Compact and Flexible
• Low Power Dissipation
• Minimal External Components
• Robust Operation in Adverse Industrial Environments
• 5V at 4A Output with 20% Over-Range Current
Applications
• PLCs
• Industrial Process Control and Sensors
• Telecom and Datacom Power Supplies
MAXREFDES115# System Board
Enlarge+
MAXREFDES115# Reference Design Block Diagram
System Board 5858
MAXREFDES115#: ISOLATED 24V TO 5V 20W POWER
SUPPLY
Introduction
Though isolated power supplies provide reliable power regulation for a variety of
applications, transformer selection is often the most difficult step in isolated power design.
The MAXREFDES115# is a compact, isolated 24V input flyback converter module that
features 5V at 4A (20W) output. Multiple transformers have been qualified for this design,
simplifying the process of transformer selection. In addition, through-hole pins on the
bottom side of the module allow quick and easy integration of this power converter into any
system. Pins are 15.24mm from power to ground, and 63.5mm from the input side to the
output side.
MAXREFDES115# System Board
Enlarge+
The MAXREFDES115# reference design (Figure 1) demonstrates the application of the
MAX17599 low IQ, wide-input range, active-clamp current-mode PWM controller. The
MAX17599 contains all the control circuitry required for the design of wide-input isolated
forward-converter industrial power supplies. The reference design features the active-
clamp transformer reset topology for forward converters. This reset topology has several
advantages including reduced voltage stress on the switches, transformer size reduction
due to larger allowable flux swing, and improved efficiency due to elimination of dissipative
snubber circuitry. These features result in a compact and cost-effective isolated power
supply. The design is set to switch at 250kHz. For EMI-sensitive applications, the user can
program the frequency-dithering scheme, enabling low-EMI spread-spectrum operation.
The input undervoltage lockout (EN/UVLO) is provided for programming the input-supply
start voltage (set to 16.5V in the design) and to ensure proper operation during brownout
conditions. The EN/UVLO input is also used to turn on/off the IC. The overvoltage input
(OVI) protection scheme is provided to make sure that the controller shuts down when the
input supply exceeds the maximum allowed value (set to 37.0V in the design).
To control inrush current, the device incorporates a soft-start (SS) pin to set the soft-start
time for the regulator. Power dissipation under fault conditions is minimized by hiccup
overcurrent protection (hiccup mode). The SS feature provides safe discharging of the
clamp capacitor when the device is turned off, and allows the controller to restart in a well-
controlled manner.
Additionally, the negative current limit is provided in the current-sense circuitry, helping
limit clamp switch current under dynamic operating conditions. An overtemperature fault
triggers thermal shutdown for reliable protection of the device. The reference design
delivers a peak efficiency of 91.5% with the supplied components when the input is 24V.
This general-purpose power solution can be used in many different types of power
applications, such as programmable logic controllers (PLC), industrial process control,
industrial sensors, telecom/datacom power supplies, isolated battery chargers, servers,
and embedded computing.
System Diagram
Figure 1. MAXREFDES115# reference design block diagram.
Detailed Circuit Description
The MAX17599 low IQ active-clamp current-mode PWM controller contains all the control
circuitry required for designing wide-input isolated forward-converter industrial power
supplies.
The device includes an AUX driver that drives an auxiliary MOSFET (clamp switch) that
helps implement the active-clamp transformer reset topology for forward converters. This
reset topology has several advantages, including reduced voltage stress on the switches,
transformer size reduction due to larger allowable flux swing, and improved efficiency due
to elimination of dissipative snubber circuitry. Programmable dead time between the AUX
and main driver allows for zero voltage switching.
Primary Power Stage
The active-clamp transformer primary side is driven by an n-channel MOSFET (N1) and a
p-channel MOSFET (P1). While N1 is on, power is delivered to the secondary, and
magnetizing energy is being stored in the transformer. During this time, P1 is off, and the
clamp capacitor (C12) is charged at a constant voltage level.
When N1 turns off, the leakage and magnetizing currents charge up the drain-to-source
capacitance of N1. Once the drain-to-source voltage of N1 exceeds the voltage across the
clamp capacitor, the body diode of P1 begins to conduct. With the body diode of P1
conducting, the magnetizing current begins to charge the clamp capacitor.
After the body diode of P1 conducts, P1 turns on. This provides zero current switching for
P1. The clamp capacitor continues to charge until the magnetizing current is reduced to
0A. At this point, the magnetizing current reverses, and the clamp capacitor begins to
discharge until the P1 turns off.
After P1 turns off, the clamp capacitor remains at a fixed voltage. There is a fixed delay
before N1 turns on. During this delay, the energy in the parasitic components discharges
the VDS of N1 towards VIN. This allows softer turn on and lower switching losses for N1.
The MAX17599 NDRV pin drives N1 while the AUXDRV pin is level shifted through C11,
R14, and D4, and then drives P1.
Secondary Power Stage
The secondary power stage consists of the synchronous rectifiers (N1, N2), and the output
filters (L2, C4, C5, C6).
When the primary n-FET (N3) is turned ON, the input power is transferred instantaneously
to the output through forward conducting MOSFET N2. During the turn-off period, the
output inductor current freewheels through MOSFET N1.
The voltage on the input end of the filter inductor is a typical buck converter square wave.
The inductor and output capacitors filter the square wave to produce a DC voltage on the
output.
Feedback Control Loop
The feedback network is constructed using a TLV431B programmable shunt regulator, a
3000V isolation optocoupler, and other RC components.
Startup Voltage and Input Overvoltage Protection Setting (EN/UVLO, OVI)
The EN/UVLO pin in the MAX17599 serves as an enable/disable input, as well as an
accurate programmable under voltage lockout (UVLO) pin. The MAX17599 does not begin
startup operations unless the EN/UVLO pin voltage exceeds 1.21V (typ). The MAX17599
turns off if the EN/UVLO pin voltage falls below 1.15V (typ). A resistor divider from the
input DC bus to ground can be used to divide down and apply a fraction of the input DC
voltage to the EN/UVLO pin. The values of the resistor divider can be selected so that the
EN/UVLO pin voltage exceeds the 1.21V (typ) turn on threshold at the desired input DC
bus voltage. The same resistor divider can be modified with an additional resistor, ROVI,
to implement overvoltage input protection in addition to the EN/UVLO functionality. When
the voltage at the OVI pin exceeds 1.21V (typ), the MAX17599 stops switching. Switching
resumes with soft-start operation, only if the voltage at the OVI pin falls below 1.15V (typ).
Quick Start
Required equipment:
• MAXREFDES115#
• One adjustable DC power supply with voltage output up to 36V and current up to 3A
• One electronic load
• Two voltmeters
• Two ammeters
Procedure
The MAXREFDES115 board is fully assembled and tested. Use the following steps to
verify board operation.
1. Turn off the power supply.
2. Connect the positive terminal of the power supply to the VIN connector of the
MAXREFDES115# board.
3. Connect the GND connector of the MAXREFDES115# board to the positive terminal
of one ammeter. Connect the negative terminal of the ammeter to the negative
terminal of the power supply.
4. Connect one voltmeter across the VIN and the GND connectors of the
MAXREFDES115# board.
5. Connect the VOUT connector of the MAXREFDES115# board to the positive terminal
of the electronic load.
6. Connect the negative terminal of the electronic load to the positive terminal of the
second ammeter. Connect the negative terminal of the ammeter to the PGNDO
connector of the MAXREFDES115# board.
7. Connect the second voltmeter across the VOUT and the PGNDO connectors of the
MAXREFDES115# board.
8. Turn on the power supply. Set the output to 24V.
9. Set the electronic load to a constant current between 0A to 4A.
10. Verify the second voltmeter reading is 5V ±0.25V.
Lab Measurements
The MAXREFDES115# was verified and tested under full input range and different output
load conditions. The power efficiency vs. load current is illustrated in Figure 2.
Figure 2. Power efficiency vs. load current for MAXREFDES115A# at 5VOUT, other
versions performed similarly.
Figure 3 displays the output ripple at full load when the input is 24V.
Figure 3. Transient response when load steps from 5mA to 1600mA.
Figure 4 displays the load transient response when the load is stepped from 5mA to
1600mA, and then dropped back to 5mA again. The output transient spike is about
240mV. The input is 24V.
Figure 4. Output ripple at 4A load, 5VOUT
.
Figure 5 shows the load transient response when the load is stepped from 2.4A to 4A, and
then dropped back to 2.4A again. The input is 24V.
Figure 5. Transient response when load steps from 2.4A to 4A, at 5VOUT
.
Part Number
MAXREFDES115A#
Enlarge+
Wurth
Transformer Vendor
Transformer Part Number
750315945
Part Number
MAXREFDES115B#
Enlarge+
Sumida
Transformer Vendor
Transformer Part Number
12387-T070
Part Number
MAXREFDES115C#
Enlarge+
Hanrun
Transformer Vendor
Transformer Part Number
HR051434
System Board 5858
MAXREFDES115#: ISOLATED 24V TO 5V 20W POWER
SUPPLY
Design Resources
Quick Start
Required equipment:
• MAXREFDES115#
• One adjustable DC power supply with voltage output up to 36V and current up to 3A
• One electronic load
• Two voltmeters
• Two ammeters
Procedure
The MAXREFDES115 board is fully assembled and tested. Use the following steps to
verify board operation.
1. Turn off the power supply.
2. Connect the positive terminal of the power supply to the VIN connector of the
MAXREFDES115# board.
3. Connect the GND connector of the MAXREFDES115# board to the positive terminal
of one ammeter. Connect the negative terminal of the ammeter to the negative
terminal of the power supply.
4. Connect one voltmeter across the VIN and the GND connectors of the
MAXREFDES115# board.
5. Connect the VOUT connector of the MAXREFDES115# board to the positive
terminal of the electronic load.
6. Connect the negative terminal of the electronic load to the positive terminal of the
second ammeter. Connect the negative terminal of the ammeter to the PGNDO
connector of the MAXREFDES115# board.
7. Connect the second voltmeter across the VOUT and the PGNDO connectors of the
MAXREFDES115# board.
8. Turn on the power supply. Set the output to 24V.
9. Set the electronic load to a constant current between 0A to 4A.
10. Verify the second voltmeter reading is 5V ±0.25V.
System Board 5858
MAXREFDES115#: ISOLATED 24V TO 5V 20W POWER
SUPPLY
Order
Key:
Material Analysis
Non-cancelable and Non-returnable
Lead-free, RoHS compliant Not qualified as lead-free RoHS # RoHS compliant, lead
Symbols in part number:
exemption
+
−
*Budgetary price. Some parts do not have standard pricing and need to be quoted.
Part Number
MAXREFDES115A#
Price /Unit*
BUY
status
Active
Part Number
MAXREFDES115B#
Price /Unit*
BUY
status
Active
Part Number
MAXREFDES115C#
Price /Unit*
BUY
status
Active
相关型号：
©2020 ICPDF网 联系我们和版权申明