MAX17065EVKIT [MAXIM]
1.2MHz PWM Switching Frequency (Selectable 600kHz, Component Change Required);型号: | MAX17065EVKIT |
厂家: | MAXIM INTEGRATED PRODUCTS |
描述: | 1.2MHz PWM Switching Frequency (Selectable 600kHz, Component Change Required) |
文件: | 总10页 (文件大小:410K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
19-4310; Rev 0; 10/08
MAX17065 Evaluation Kit
Evluates:MAX17065
General Description
Features
The MAX17065 evaluation kit (EV kit) is a fully assem-
bled and tested surface-mount PCB that evaluates the
high-efficiency MAX17065 organic LED (OLED) driver.
The MAX17065 EV kit operates from a +2.3V to +4.5V
single power supply and includes dual switch-mode
power-supply (SMPS) outputs, one LDO, and dual reg-
ulated charge pumps for an OLED panel.
o +2.3V to +4.5V Input Range
o 85% Efficiency (VIN = +3.3V, I = I = 120mA)
VP
VN
o +5.35V/120mA Positive and -4.5V/120mA Negative
SMPS (-5V to -0.5V Adjustable Negative SMPS,
Component Change Required)
o +1.9V/60mA LDO
2
™
The MAX17065 EV kit provides an on-board I C/SMBus
o +6.5V/2mA Positive and -4V/2mA Negative
Regulated Charge Pumps (+5.5V to +9V Adjustable
Positive and -5V to -0.5V Adjustable Negative
Charge Pump)
interface and is connected to the computer through the
universal serial bus (USB) port. The EV kit includes
Windows® 2000/XP- and Windows Vista®-compatible
software that provides a graphical user interface (GUI)
for control of the MAX17065’s output voltages, switching
frequency, operating mode, current limit, and SMPS and
charge-pump enables.
o 1.2MHz PWM Switching Frequency (Selectable
600kHz, Component Change Required)
2
o On-Board I C/SMBus Interface Control Through USB
o Shutdown Control
o Fully Assembled and Tested
Ordering Information
PART
TYPE
PC INTERFACE
SMBus is a trademark of Intel Corp.
MAX17065EVKIT+
EV Kit
USB
Windows and Windows Vista are registered trademarks of
Microsoft Corp.
+Denotes lead-free and RoHS-compliant.
Component List
DESIGNATION QTY
DESCRIPTION
DESIGNATION QTY
DESCRIPTION
10µF 10ꢀ, 16V X5R ceramic
capacitors (0805)
KEMET C0805C106K4PACTU
0.01µF 10ꢀ, 50V X7R ceramic
capacitor (0603)
Murata GRM188R71H103K
TDK C1608X7R1H103K
C1, C12, C14
3
C22
C23
1
1
2
1
3
22pF 5ꢀ, 50V C0G ceramic
capacitors (0603)
Murata GRM1885C1H220J or
TDK C1608C0G1H220J
2200pF 10ꢀ, 50V X7R ceramic
capacitor (0603)
Murata GRM188R71H222K
TDK C1608X7R1H222K
C2, C3
2
0.033µF 10ꢀ, 16V X5R ceramic
capacitor (0603)
Taiyo Yuden EMK107BJ333KA
C4
1
470pF 10ꢀ, 50V X7R ceramic
capacitors (0603)
Murata GRM188R71H471K
TDK C1608X7R1H471K
C24, C25
C26
0.1µF 10ꢀ, 16V X7R ceramic
capacitors (0603)
TDK C1608X7R1C104K
Murata GRM188R71C104K
C5–C10, C17,
C18, C28, C29,
C30, C34
12
2.2µF 10ꢀ, 10V X5R ceramic
capacitor (0603)
Murata GRM188R61A225K
TDK C1608X5R0J225K
1µF 10ꢀ, 16V X7R ceramic
capacitors (0603)
Murata GRM188R71C105K
TDK C1608X5R1C105K
C11, C13, C19,
C20, C21,
10
2
4.7µF 10ꢀ, 10V X5R ceramic
capacitors (0805)
Murata GRM219R61A475K
TDK C2012X5R1A475K
C35–C39
C27, C31, C32
10pF 5ꢀ, 50V C0G ceramic
capacitors (0603)
Murata GRM1885C1H100J
TDK C1608C0G1H100J
C15, C16
*EP = Exposed pad.
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX17065 Evaluation Kit
Component List (continued)
DESIGNATION QTY
DESCRIPTION
DESIGNATION QTY
DESCRIPTION
Adjustable output LDO regulator
(5 SO70)
Maxim MAX8512EXK+
10µF 10ꢀ, 6.3V X5R ceramic
capacitor (0603)
TDK C1608X5R0J106K
Murata GRM188R60J106M
U4
1
C33
1
UART-to-USB converter
FTDI FT232BL (32 TQFP)
U5
U6
1
1
2
H1
JU1
0
1
3
0
Not installed, 2 x 5-pin JTAG header
2-pin header
93C46 type 3-wire EEPROM
Atmel AT93C46A-10SU-2.7 (8 SO)
JU2, JU5, JU6
JU3, JU4
3-pin headers
®
Logic level translators (10 µMAX )
Not installed, 2-pin headers
U7, U8
Maxim MAX1840EUB+
Ferrite bead (0603)
Y1
1
1
4
1
16MHz crystal
L1
L2, L3
P1
1
2
1
TDK MMZ1608R301A
Murata BLM18SG700 TN1
Y2
6MHz crystal
4.7µH, 0.75A, 0.18Ω inductors
TDK VLF3010ST-4R7MR75
Taiyo Yuden NR3010T4R7M (0.24Ω)
USB series-B right-angle PC-mount
receptacle
—
Shunts
—
PCB: MAX17065 Evaluation Kit+
*EP = Exposed pad.
Component Suppliers
Assmann Electronic AU-Y1007-R
Evluates:MAX17065
R1, R2
R3
2
1
1
1
1
1
1
27Ω 5ꢀ resistors (0603)
1.5kΩ 5ꢀ resistor (0603)
470Ω 5ꢀ resistor (0603)
2.2kΩ 5ꢀ resistor (0603)
10kΩ 5ꢀ resistor (0603)
169kΩ 1ꢀ resistor (0603)
100kΩ 1ꢀ resistors (0603)
SUPPLIER
PHONE
WEBSITE
Assmann
Electronic
480-897-7001 www.assmann.com
864-963-6300 www.kemet.com
R4
R5
KEMET Corp.
R6
Murata
Electronics North
America, Inc.
R7
770-436-1300 www.murata-northamerica.com
R8
Taiyo Yuden
TDK Corp.
800-348-2496 www.t-yuden.com
Not installed, resistors—short by
PCB trace (0402)
R9–R13
R14, R15
R16
0
2
0
847-803-6100 www.component.tdk.com
33.2kΩ 1ꢀ resistors (0603)
Note: Indicate that you are using the MAX17065 when contact-
ing these component suppliers.
Not installed, resistor—short by PCB
trace (0603)
MAX17065 EV Kit Files
R17
1
0
2
1MΩ 5ꢀ resistor (0603)
Not installed, resistors (0603)
100Ω 1ꢀ resistors (0603)
R18–R21
R22, R23
FILE
DESCRIPTION
Installs the EV kit files on
your computer
INSTALL.EXE
OLED driver (28 TQFN)
Maxim MAX17065ETI+
U1
U2
U3
1
1
1
MAX17065.EXE
FTD2XX.INF
UNINST.INI
Application program
USB Driver file
Microcontroller (68 QFN-EP*)
Maxim MAXQ2000-RAX+
Uninstalls the EV kit software
2.5V LDO regulator (5 SO70)
Maxim MAX8511EXK25+
TROUBLESHOOTING_USB.PDF USB driver installation help file
µMAX is a registered trademark of Maxim Integrated Products, Inc.
_______________________________________________________________________________________
2
MAX17065 Evaluation Kit
Evluates:MAX17065
described above after 30 seconds, remove the USB
Quick Start
Recommended Equipment
Before beginning, the following equipment is needed:
cable from the board and reconnect it. Administrator
privileges are required to install the USB device dri-
ver on Windows. Refer to the TROUBLESHOOT-
ING_USB.PDF document included with the software
if you have any problems during this step.
•
•
MAX170655 EV kit (USB cable included)
A user-supplied Windows® 2000/XP or Windows
Vista PC
6) Follow the directions of the Add New Hardware
Wizard to install the USB device driver. Choose the
Search for the best driver for your device option.
Specify the location of the device driver to be
C:\Program Files\MAX17065 (default installation
directory) using the Browse button.
•
•
+2.3V to +4.5V, 1A power supply (VIN)
Available USB port
Note: In the following sections, software-related items
are identified by bolding. Text in bold refers to items
directly from the EV kit. Text in bold and underlined
refers to items from the Windows operating system.
7) Set the VIN power supply and enable its output.
8) Start the MAX17065 program by opening its icon in
the Start menu.
Procedure
The MAX17065 EV kit is fully assembled and tested.
Follow the steps below to verify board operation.
Caution: Do not turn on the power supply until all
connections are completed.
9) Normal device operation is verified when CMAXQUSB
HW: Connected. MAX17065 device connected. is
displayed at the bottom left of the MAX17065 EV
kit window.
1) Visit www.maxim-ic.com/evkitsoftware to down-
load the latest version of the EV kit software,
17065Rxx.ZIP. Save the EV kit software to a tempo-
rary folder and uncompress the ZIP file.
10) Set the switching frequency = 1.2MHz, negative
SMPS = -4.5V, positive and negative current limits
= 0.7A, positive charge-pump output = +6.5V, and
negative charge-pump output = -4V (Figure 1).
2) Install the EV kit software on your computer by run-
ning the INSTALL.EXE program. The program files
are copied and icons are created in the Windows
Start menu.
3) Verify that jumpers are in their default positions as
follows:
JUMPER
JU1
SHUNT POSITION
Installed
JU2, JU5, JU6
1-2
4) Connect the positive terminal of the VIN power sup-
ply to the VIN pad. Connect the ground terminal of
the VIN power supply to the PGND pad.
5) Connect the USB cable from the PC to the EV kit
board. A Building Driver Database window pops
up in addition to a New Hardware Found message
when installing the USB driver for the first time. If
you do not see a window that is similar to the one
Figure 1. MAX17065 EV Kit Software Suggested Setup
_______________________________________________________________________________________
3
MAX17065 Evaluation Kit
ON Enables and Test
The ON2 and ON1 bits enable/disable the various out-
puts of the MAX17065, according to Table 1. To set
either bit high, check the respective ON_ checkbox in
the ON Enables group box.
Detailed Description of Software
User-Interface Panel
The program’s main window (Figure 2) is navigated by
using a mouse or a combination of the Tab and Arrow
keys. The MAX17065 EV kit software provides controls
for the following software-configurable features:
Frequency and Mode selection, ON Enables, Outputs
configuration, Faults detection, Current Limit settings,
and Manufacturer ID/Silicon Revision detection.
Changes to the controls result in a write operation that
updates the appropriate registers of the MAX17065.
A status bar is also provided at the bottom of the pro-
gram’s main window and is used to verify command
module and device connectivity. A Device Search
option is located in the Action menu bar should the user
want to switch from Demo Mode to normal operation.
Table 1. ON2 and ON1 Control
VH, VL
OUTPUTS
VP, VN
OUTPUTS
ON2
ON1
VA OUTPUT
0
0
1
1
0
1
0
1
Off
On
On
On
Off
On
On
On
Off
Off
On
On
Setting TEST1 and TEST0 checkboxes prevents the
VL, VH, VP, and VN outputs. In this mode, the output
can be driven by external voltage sources. Setting
either TEST_ bit to 1 in the Test group box disables the
discharge function. Refer to the MAX17065 IC data
sheet for more information regarding the test bits.
Evluates:MAX17065
Fault Detection
The MAX17065’s Faults read-only register monitors the
OLED controller’s operating state, output, and thermal
faults. When a fault is detected, the corresponding bit is
changed from logic 0 to logic 1 and the font color is
changed to red. Refer to the MAX17065 IC data sheet
for more information regarding the Faults register.
Outputs
The MAX17065 allows for software control of the
charge-pump and negative SMPS outputs. Select the
appropriate voltages from the VL:, VH:, and VN: drop-
down lists to set the desired voltages. The default set-
tings are VL: -0.5V, VH: +5.5V, and VN: -0.5V.
Figure 2. MAX17065 EV Kit Software Main Window
Current Limit
The MAX17065 software allows the user to set cur-
rent limits for the negative and positive switching
power supplies. To set the current limits, select the
desired current limit from the IMAXN: and IMAXP:
drop-down lists in the Current Limit group box. The
default current-limit settings are IMAXN: 0.45A and
IMAXP: 0.45A.
Frequency Selection
The MAX17065 can be operated at either 0.6MHz or
1.2MHz. To set the desired frequency, select the
appropriate radio button in the Frequency group box.
The default frequency setting is 0.6MHz, but the EV kit
is designed for 1.2MHz. Component changes are
required when selecting different frequencies. Refer to
the MAX17065 IC data sheet for more information
regarding frequency selection.
Manufacturer ID/Silicon
Revision Detection
The ID Register group box shows the manufacturer ID
and silicon revision information of the MAX17065 IC.
This information is read upon initial start-up.
Operating Mode
The MAX17065 can be operated in either Skip Mode or
Forced PWM. To set the desired operating mode,
select the appropriate radio button in the Mode group
box. The default operating mode is Forced PWM. Refer
to the MAX17065 IC data sheet for more information
regarding modes of operation.
4
_______________________________________________________________________________________
MAX17065 Evaluation Kit
Evluates:MAX17065
2
The MAX17065 includes dual SMPS outputs (+5.35
fixed positive and -5V to -0.5V adjustable negative),
one LDO (+1.9V/60mA), and dual regulated charge
pumps (+5.5V to +9V positive and -5V to -0.5V nega-
tive) for an OLED panel.
Simple I C/SMBus Commands
There are two methods for communicating with the
MAX17065: through the normal user-interface panel
(Figure 2) or through the I2C/SMBus commands, avail-
able by selecting the Interface Diagnostic Window
menu item from the Action menu bar. The Maxim
Command Module Interface window pops up and
includes a 2-wire interface tab that allows for execu-
tion of simple I2C/SMBus commands.
Shutdown Control
The MAX7065 can be placed in shutdown mode
through jumper JU1 (see Table 2). When connected to
GND or left open, the VD output is enabled with four ris-
ing CLK edges. When connected to VDDIO, the
MAX17065’s VD is enabled without a CLK signal.
The SMBus dialog boxes accept numeric data in bina-
ry, decimal, or hexadecimal. Hexadecimal numbers
should be prefixed by $ or 0x. Binary numbers must be
exactly eight digits. See Figure 3 for an illustration
of this tool.
Table 2. Jumper JU1 Function
SHUNT
POSITION
LDO OUTPUT
(VD)
SHDN PIN
Connected to
VDDIO
Installed*
Always on
Internally
connected to GND
Enabled with four
rising CLK edges
One pin
*Default position.
User-Supplied VDDIO Input
The MAX17065’s VDDIO supply is powered from the
USB port by default. Move the shunt of JU2 to the 2-3
position to apply your own +1.6V to +3.6V power sup-
ply at the VDDIO pad. See Table 3 for jumper JU2 con-
figuration. VDDIO voltage decides the SHDN and CLK
logic levels. When CLK is driven by an external signal,
jumper JU2 can be placed in a 2-3 position to allow
external VDDIO voltage.
Table 3. Jumper JU2 Function
Figure 3. Interface Diagnostic Window
SHUNT
VDDIO PIN
POSITION
1-2*
2-3
Powered from +3.3V USB supply
Detailed Description of Hardware
Powered from external +1.6V to +3.6V supply
The MAX17065 evaluation kit (EV kit) is a fully assem-
bled and tested surface-mount PCB that evaluates the
high-efficiency MAX17065 organic LED (OLED) driver.
The MAX17065 EV kit provides an on-board I2C/SMBus
interface and is connected to the computer through the
USB port. The EV kit includes Windows 2000/XP- and
Windows Vista-compatible software that provides a GUI
for control of the MAX17065’s output voltages, switch-
ing frequency, operating mode, current limit, and SMPS
and charge-pump enables. The MAX17065 EV kit oper-
ates from a +2.3V to +4.5V single power supply.
*Default position.
User-Supplied I2C/SMBus Interface
To use the MAX17065 EV kit with a user-supplied
I2C/SMBus interface, first move the shunts of JU5 and
JU6 to the 2-3 position. Then connect your SDA and
SCL signals to the corresponding SDA and SCL pads
on the MAX17065 EV kit board. Note: The I2C/SMBus
interface is not available until VD is enabled by either
SHDN = VDDIO or four rising CLK edges because SDA
and SCL are pulled up by internal 10kΩ resistors.
_______________________________________________________________________________________
5
MAX17065 Evaluation Kit
Evluates:MAX17065
Figure 4a. MAX17065 EV Kit Schematic (Sheet 1 of 2)
6
_______________________________________________________________________________________
MAX17065 Evaluation Kit
Evluates:MAX17065
Figure 4b. MAX17065 EV Kit Schematic (Sheet 2 of 2)
_______________________________________________________________________________________
7
MAX17065 Evaluation Kit
Evluates:MAX17065
Figure 5. MAX17065 EV Kit Component Placement Guide—Component Side
8
_______________________________________________________________________________________
MAX17065 Evaluation Kit
Evluates:MAX17065
Figure 6. MAX17065 EV Kit PCB Layout—Component Side
_______________________________________________________________________________________
9
MAX17065 Evaluation Kit
Evluates:MAX17065
Figure 7. MAX17065 EV Kit PCB Layout—Solder Side
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
10 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2008 Maxim Integrated Products
is a registered trademark of Maxim Integrated Products, Inc.
相关型号:
MAX1706C
1- to 3-Cell, High-Current, Low-Noise, Step-Up DC-DC Converters with Linear Regulator
MAXIM
MAX1706C/D
1- to 3-Cell, High-Current, Low-Noise, Step-Up DC-DC Converters with Linear Regulator
MAXIM
MAX1706D
1- to 3-Cell, High-Current, Low-Noise, Step-Up DC-DC Converters with Linear Regulator
MAXIM
MAX1706EEE
1- to 3-Cell, High-Current, Low-Noise, Step-Up DC-DC Converters with Linear Regulator
MAXIM
MAX1706EEE+T
Switching Regulator, Voltage-mode, 0.95A, 340kHz Switching Freq-Max, PDSO16, 0.150 INCH, 0.025 INCH PITCH, LEAD FREE, QSOP-16
MAXIM
MAX1706EEE-T
Switching Regulator, Voltage-mode, 0.95A, 340kHz Switching Freq-Max, CMOS, PDSO16, 0.150 INCH, 0.025 INCH PITCH, MO-137AB, QSOP-16
MAXIM
©2020 ICPDF网 联系我们和版权申明