MAX15049EVKIT [MAXIM]
Optional 4.5V to 5.5V Input-Voltage Operation;
| 型号： | MAX15049EVKIT |
| 厂家： | 
MAXIM INTEGRATED PRODUCTS |
| 描述： | Optional 4.5V to 5.5V Input-Voltage Operation |
| 文件： | 总7页 (文件大小：837K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
19-5149; Rev 0; 1/10
MAX15049 Evaluation Kit
General Description
Features
S Triple-Output Power Supply
VOUT1 (3.3V, 3A)
The MAX15049 evaluation kit (EV kit) is a fully assembled
and tested PCB that demonstrates the capabilities of
the MAX15049. The MAX15049 is a high-performance,
triple-output synchronous buck controller with sequenc-
ing capability. The EV kit requires a 5V to 16V (12V, typ)
DC input-voltage range for normal operation.
VOUT2 (1.8V, 3A)
VOUT3 (1.2V, 6A)
S 5.5V to 16V Input-Voltage Operation (Design
Optimized for 12V Input)
The MAX15049 EV kit outputs are configured for 3.3V,
1.8V, and 1.2V. They provide a load current of 3A, 3A,
and 6A, respectively. The EV kit’s switching frequency
is set to 500kHz, but can be programmed up to 1.2MHz
by replacing a resistor. The EV kit comes configured
for sequencing (MAX15049) and is capable of prebias
startup. The EV kit can also be used to evaluate the
MAX15048 for tracking applications by changing a few
components. The PGOOD logic signal output pad is
provided for circuit monitoring.
S Optional 4.5V to 5.5V Input-Voltage Operation
S 500kHz Switching Frequency per Converter
S Programmable Switching Frequency Up to 1.2MHz
S Sequencing Operation (Tracking Possible with
Component Changes)
S PGOOD Power Monitoring
S Small 1.5in x 1in Circuit Footprint
S 92.8% Peak Efficiency for OUT1
S Fully Assembled and Tested
The MAX15049 EV kit comes with a MAX15049ETJ+
installed. To evaluate the MAX15048, contact the factory
for samples of the pin-compatible MAX15048ETJ+.
Ordering Information
PART
TYPE
MAX15049EVKIT+
EV Kit
+Denotes lead(Pb)-free and RoHS compliant.
Component List
DESIGNATION
QTY
DESCRIPTION
DESIGNATION
QTY
DESCRIPTION
22FF Q20%, 16V X5R ceramic
capacitors (1206)
Murata GRM31CR61C226M
22pF Q5%, 50V C0G ceramic
capacitors (0402)
Murata GRM1555C1H220J
C1, C8, C9,
C18, C19, C38
6
C12, C23, C30
3
1FF Q10%, 16V X5R ceramic
capacitor (0603)
Murata GRM188R61C105K
1500pF Q10%, 50V X7R
ceramic capacitors (0402)
Murata GRM155R71H152K
C2
1
7
2
2
2
C13, C21, C32
C14, C24
3
0
2
Not installed, ceramic
capacitors (0402)
C5, C7, C15,
C17, C25, C26,
C35
0.1FF Q10%, 16V X5R ceramic
capacitors (0402)
Murata GRM155R61A104K
100FF Q20%, 6.3V X5R ceramic
capacitors (1210)
Murata GRM32ER60J107M
C27, C28
10FF Q10%, 16V X5R ceramic
capacitors (0805)
Murata GRM21BR61C106K
C6, C16
C10, C20
C11, C22
220pF Q10%, 10V X7R ceramic
capacitor (0402)
Murata GRM155R61A103K
C29
C31
1
1
0.1FF Q10%, 16V X7R ceramic
capacitors (0603)
Murata GRM188R71C104K
680pF Q10%, 50V X7R ceramic
capacitor (0402)
Murata GRM155R71H681K
330pF Q5% 50V C0G ceramic
capacitors (0402)
Murata GRM1555C1H331J
_______________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX15049 Evaluation Kit
Component List (continued)
DESIGNATION
QTY
DESCRIPTION
DESIGNATION
R1, R7, R13
R2, R8, R19
QTY
DESCRIPTION
0I Q5% resistors (0402)
Not installed, resistors (0402)
3
0
1FF Q10%, 6.3V X5R ceramic
capacitor (0402)
C33
1
Murata GRM155R60J105K
R3, R9, R16,
R18
4
24.9kI Q1% resistors (0402)
2.2FF Q20%, 6.3V X5R ceramic
capacitor (0402)
Murata GRM155R60J225M
C34
1
3
6
R4, R10, R17
3
2
1
1
1
1
1
1
1
3
1
1
1
0
15kI Q1% resistors (0402)
1kI Q1% resistors (0402)
5.49kI Q1% resistor (0402)
12.4kI Q1% resistor (0402)
20I Q5% resistor (0402)
499I Q1% resistor (0402)
2.2I Q5% resistor (0402)
39.2kI Q1% resistor (0402)
20kI Q5% resistor (0402)
10kI Q1% resistors (0402)
4.99kI Q1% resistor (0402)
2.49kI Q1% resistor (0402)
59kI Q1% resistor (0402)
Not installed, resistor (0603)
R5, R11
R6
1000pF Q10%, 50V X7R
ceramic capacitors (0402)
Murata GRM155R71H102K
C36, C37, C39
R12
R14
R15
EN1, EN2, EN3,
PGOOD, REG,
SGND
R20
1-pin headers
R21
R22
JU1
0
2
Not installed, 2-pin header
R23, R24, R28
R25
3.3FH, 7A, 26mI inductors
Vishay IHLP2525CZER3R3M07
L1, L2
R26
1FH, 14.1A, 7.1mI inductor
TDK SPM6530T-1R0M120
L3
1
2
R27
R29
30V dual n-channel
N1, N2
PowerTrench MOSFETs (MLP)
Fairchild FDMC8200
Triple-output buck controller
(32 TQFN–EP*)
Maxim MAX15049ETJ+
U1
1
1
9.1A/11A, 30V dual n-channel
MOSFET (SO8)
International Rectifier
IRF7907PbF
PCB: MAX15049 EVALUATION
KIT+
—
N3
1
*EP = Exposed pad.
Component Suppliers
SUPPLIER
Fairchild Semiconductor
International Rectifier
Murata Electronics North America, Inc.
TDK Corp.
PHONE
WEBSITE
www.fairchildsemi.com
www.irf.com
888-522-5372
310-322-3331
770-436-1300
847-803-6100
402-563-6866
www.murata-northamerica.com
www.component.tdk.com
www.vishay.com
Vishay
Note: Indicate that you are using the MAX15049 when contacting these component suppliers.
2
______________________________________________________________________________________
MAX15049 Evaluation Kit
Quick Start
Required Equipment
Detailed Description of Hardware
The MAX15049 EV kit is a fully assembled and tested
PCB that demonstrates the MAX15049, which inte-
grates three high-performance PWM switching step-
down DC-DC controllers. The EV kit circuit operates over
the input-voltage range of 4.7V to 16V. The three outputs
are configured for 3.3V, 1.8V, and 1.2V and can provide
3A, 3A, and 6A, respectively. The EV kit outputs operate
in sequencing mode during startup and the three outputs
operate 120 degrees out of phase. The EV kit outputs
can start into prebiased loads. The EV kit switching fre-
quency is set to 500kHz with resistor R21. The switching
frequency can be programmed from 200kHz to 1.2MHz
by replacing this resistor. The EV kit has a PGOOD out-
put pad to indicate that all outputs have reached their
steady-state values. The EV kit PCB is designed in four
layers and 2oz copper for optimum performance.
•ꢀ MAX15049ꢀEVꢀkit
•ꢀ 12V,ꢀ10Aꢀpowerꢀsupply
•ꢀ Fourꢀvoltmeters
Procedure
The MAX15049 EV kit is fully assembled and
tested. Follow the steps below to verify board operation.
Caution: Do not turn on the power supply until all
connections are completed.
1) Verify that U1 is installed on the bottom side of the
PCB.
2) Connect the positive terminal of voltmeter 1 (VM1)
to the OUT1 pad. Connect the negative terminal of
VM1 to the GND1 pad.
3) Connect the positive terminal of voltmeter 2 (VM2)
to the OUT2 pad. Connect the negative terminal of
VM2 to the GND2 pad.
Input Source
The MAX15049 EV kit is configured for normal operation
with an input power source of 4.7V to 16V and design
optimized for a 12V input voltage. The upper input-
voltage limit can be raised to 23V by replacing capaci-
tors C1, C2, C6, C16, and C38 with higher voltage-rated
capacitors. The EV kit circuit requires a minimum 4.7V
input voltage to start the power MOSFET switching.
4) Connect the positive terminal of voltmeter 3 (VM3)
to the OUT3 pad. Connect the negative terminal of
VM3 to the GND3 pad.
5) Connect the positive terminal of voltmeter 4 (VM4)
to PGOOD (TP8) and the negative terminal to the
PGND pad.
MAX15049 Bias Input
The MAX15049 EV kit features an option to select the
bias input for the MAX15049 when configuring the EV kit
to operate with an input source less than 4.7V. Jumper
JU1 shorts the input-voltage source for the MAX15049 to
the controller REG pin. Without JU1 installed, the input-
voltage range in this configuration is 4.7V to 16V.
6) Set the power supply to 12V and disable the output.
7) Connect the positive terminal of the power supply
to the VIN pad. Connect the negative terminal of the
power supply to the PGND pad.
8) Turn on the power supply.
9) Verify that the VOUT1, VOUT2, and VOUT3 outputs
measure 3.3V, 1.8V, and 1.2V, respectively.
When operating the MAX15049 EV kit with a supply
between 4.5V to 5.5V, install jumper JU1.
10) Verify that PGOOD measures approximately 5V.
11) The EV kit is now ready for load testing. Use the
respective OUT_ connector load points for high-
current load testing.
Table 1. MAX15049 Bias Input Configuration (JU1)
SHUNT POSITION
MAX15049 IN PIN
Connected to REG
Connected to VIN
MAX15049 EV KIT INPUT RANGE (V)
Installed
4.5 to 5.5
4.7 to 16
Not installed
_______________________________________________________________________________________
3
MAX15049 Evaluation Kit
Triple Outputs
The MAX15049 EV kit’s three outputs are configured to
different voltages. The bottom side of the PCB contains
the IC and the feedback and compensation compo-
nents. The top side of the PCB contains the input/output
capacitors, inductors, and FETs. OUT1 is configured to
3.3V with resistors R3 and R6 and can supply up to 3A.
OUT2 is configured to 1.8V with resistors R9 and R12
and can supply up to 3A. OUT3 is configured to 1.2V
with resistors R16 and R18 and can supply up to 6A.
The output voltage for each output can be reconfigured
between 0.6V and 3.3V by replacing the respective feed-
back resistors. Refer to the Type III: Compensation When
Switching Frequency
The MAX15049 PWM switching frequency is set to appro-
ximately 500kHz with resistor R21 (39.2kI). Replace
resistor R21 with a new resistor value to progam the
switching frequency between 200kHz and 1.2MHz. Use
the following equation to choose the appropriate resistor
value to reconfigure the switching frequency (f ):
SW
f
kHz = 12.8×R21 kΩ
(
)
(
)
SW
Evaluating the MAX15048 (Tracking)
The MAX15049 EV kit comes configured for sequencing.
The EV kit can also evaluate the MAX15048 for tracking
applications. The MAX15049 IC must be replaced with
the MAX15048. It also requires modification at EN2
(pin 9) and EN3 (pin 24) for tracking operation with
the MAX15048. Refer to the MAX15048 Coincident/
Ratiometric Tracking (EN_) section in the MAX15048/
MAX15049 IC data sheet to calculate the proper values
for resistors R23–R26 and R29.
ƒ
< ƒ
section in the MAX15048/MAX15049
CO
ZERO, ESR
IC data sheet for instructions on selecting new resis-
tor values for the respective outputs. Also, refer to the
Inductor Selection and Input-Capacitor Selection sec-
tions in the IC data sheet to verify other component
replacements for proper operation when changing the
output voltage.
Current Limit
PGOOD Status Output
The MAX15049 EV kit provides a PGOOD logic output to
indicate the regulation state of OUT1, OUT2, and OUT3.
A logic-low at TP8 (PGOOD test point) indicates that one
of the output voltages has dropped below 92% of its
regulation voltage.
The MAX15049 EV kit uses the low-side MOSFET DC
on resistance (R
) for valley current sensing. The
current-limit threshold is 69mV internally set inside
the MAX15049. The MAX15049 compares the voltage
DSON
across the low-side MOSFET (R
) with the internal
DSON
threshold to incorporate the current limit. OUT1 and
OUT2 use the FDMC8200 FET with a low-side R of
Individual EN_ Input
The MAX15049 EV kit provides an individual enable test
point for each output. The EV kit comes configured for
sequencing and connections so the enable test points
are not needed. To disable sequencing and externally
control each output, remove the sequencing compo-
nents (R23–R28) and apply a voltage on the EN_ test
point.
DSON
9.5mI(typ) and 13.5mI(max). The current-limit thresh-
old is 69mV (typ) and the output current limit calculated
is approximately 6A. The IRF7907 FET has similar char-
acteristics with a 9.1mI(typ) and 13.7mI(max) R
DSON
and therefore, a similar current limit.
4
______________________________________________________________________________________
MAX15049 Evaluation Kit
Figure 1. MAX15049 EV Kit Schematic
_______________________________________________________________________________________
5
MAX15049 Evaluation Kit
1.0”
1.0”
Figure 2. MAX15049 EV Kit Component Placement Guide—
Component Side
Figure 3. MAX15049 EV Kit PCB Layout—Component Side
1.0”
Figure 4. MAX15049 EV Kit PCB Layout—Layer 2 (Ground
Layer)
6
______________________________________________________________________________________
MAX15049 Evaluation Kit
1.0”
1.0”
Figure 5. MAX15049 EV Kit PCB Layout—Layer 3
(Power Layer)
Figure 6. MAX15049 EV Kit PCB Layout—Solder Side
1.0”
Figure 7. MAX15049 EV Kit Component Placement Guide—
Solder Side
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.
Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
7
©
2010 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products, Inc.
相关型号：
MAX15050EWE+
Switching Regulator, Voltage-mode, 4A, 1100kHz Switching Freq-Max, BICMOS, PBGA16, 2 X 2 MM, 0.50 MM PITCH, ROHS COMPLIANT, WLP-16
MAXIM
MAX15051EWE+
Switching Regulator, Voltage-mode, 4A, 1100kHz Switching Freq-Max, BICMOS, PBGA16, 2 X 2 MM, 0.50 MM PITCH, ROHS COMPLIANT, WLP-16
MAXIM
MAX15051EWE+T
Battery Charge Controller, Voltage-mode, 4A, 1100kHz Switching Freq-Max, BICMOS, PBGA16,
MAXIM
MAX15053EWL+T
Switching Regulator, Current-mode, 1150kHz Switching Freq-Max, BICMOS, PBGA9, 1.50 X 1.50 MM, 0.50 MM PITCH, ROHS COMPLIANT, WLP-9
MAXIM
©2020 ICPDF网 联系我们和版权申明