MAX15006AATT+ [MAXIM]
40V, Ultra-Low Quiescent-Current Linear Regulators in 6-Pin TDFN/8-Pin SO; 40V ,超低静态电流线性稳压器,6引脚TDFN / 8引脚SO型号: | MAX15006AATT+ |
厂家: | MAXIM INTEGRATED PRODUCTS |
描述: | 40V, Ultra-Low Quiescent-Current Linear Regulators in 6-Pin TDFN/8-Pin SO |
文件: | 总15页 (文件大小:314K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
19-0663; Rev 0; 10/06
40V, Ultra-Low Quiescent-Current
Linear Regulators in 6-Pin TDFN/8-Pin SO
6/MAX1507
General Description
Features
o Wide Operating Input Voltage Range (4V to 40V)
o Guaranteed 50mA Output Current
The MAX15006/MAX15007 ultra-low quiescent-current
linear regulators are ideal for use in automotive and
battery-operated systems. These devices operate from
an input voltage of 4V to 40V, deliver up to 50mA of out-
put current, and consume only 10µA of quiescent cur-
rent at no load. The internal p-channel pass device
keeps the quiescent current low even at full load. The
MAX15007 consumes only 3µA current when in shut-
down.
o Low Quiescent Current
10µA (No Load) and 90µA (Full Load)
o Operates Through Cold-Crank Condition
o Withstands 45V Load Dump
o Low Dropout Voltage of 300mV
(MAX15006B/MAX15007B)
The MAX15006A/MAX15007A have a fixed 3.3V output
while the MAX15006B/MAX15007B have a fixed 5V out-
put voltage. The MAX15007 includes an enable input to
turn the device on or off. All devices are short-circuit
protected and include thermal shutdown.
o Stable Operation with Tiny 2.2µF Output
Capacitor
o Enable Input (MAX15007)
o Preset 3.3V and 5.0V Output Voltages
o Thermal and Short-Circuit Protection
o -40°C to +125°C Operating Temperature Range
The MAX15006/MAX15007 operate over the -40°C to
+125°C automotive temperature range. These devices
are available in space-saving 3mm x 3mm 6-pin TDFN
and 8-pin SO thermally enhanced packages.
o Thermally Enhanced 3mm x 3mm 6-Pin TDFN/
8-Pin SO Packages
Ordering Information
Applications
PIN-
PACKAGE
TOP
MARK
PKG
CODE
PART
Automotive
MAX15006AASA+ 8 SO-EP*
MAX15006AATT+ 6 TDFN-EP*
MAX15006BASA+ 8 SO-EP*
MAX15006BATT+ 6 TDFN-EP*
—
APE
—
S8E-12
T633-2
S8E-12
T633-2
Tire-Pressure Monitoring
Industrial
Telecom
APF
Networking
Ordering Information continued at end of data sheet.
Note: All devices are specified over the -40°C to +125°C oper-
ating temperature range.
+Denotes lead-free package.
*EP = Exposed pad.
Pin Configurations
TOP VIEW
OUT
6
OUT
5
GND
4
MAX15006A
MAX15006B
+
IN
N.C.
N.C.
N.C.
1
2
3
4
8
7
6
5
OUT
N.C.
N.C.
GND
MAX15006A
MAX15006B
*EP
+
*EP
1
2
IN
3
SO
IN
N.C.
*EXPOSED PAD
TDFN
Pin Configurations continued at end of data sheet.
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
40V, Ultra-Low Quiescent-Current
Linear Regulators in 6-Pin TDFN/8-Pin SO
ABSOLUTE MAXIMUM RATINGS
IN to GND...............................................................-0.3V to +45V
EN to GND..............................................................-0.3V to +45V
OUT to GND ...........................................................-0.3V to +12V
OUT Short-Circuit Duration ........................................Continuous
Maximum Current Into Any Pin (except IN and OUT) ...... 50mA
Thermal Resistance
θ
JA
θ
JC
θ
JA
θ
JC
, 6-Pin TDFN ...........................................................42°C/W
, 6-Pin TDFN ..........................................................8.5°C/W
, 8-Pin SO-EP..........................................................43°C/W
, 8-Pin SO-EP............................................................7°C/W
Continuous Power Dissipation (T = +70°C)
6-Pin TDFN-EP (derate 23.8mW/°C above +70°C) .......1904mW*
8-Pin SO-EP (derate 23.3mW/°C above +70°C).........1860mW*
Operating Temperature Range .........................-40°C to +125°C
Junction Temperature......................................................+150°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
A
*As per JEDEC51 Standard (Multilayer Board).
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V = 14V, I
= 1mA, C = 0.1µF, C
= 2.2µF, T = T = -40°C to +125°C, unless otherwise noted. Typical specifications are
IN
OUT
IN
OUT
A
J
at T = +25°C.) (Note 1)
A
6/MAX1507
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
40
UNITS
Input Voltage Range
V
4
V
IN
I
I
I
I
I
I
I
I
= 0 (MAX15006)
10
11
17
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
= 0 (MAX15007)
18
= 100µA (MAX15006)
= 100µA (MAX15007)
= 1mA (MAX15006)
= 1mA (MAX15007)
= 50mA (MAX15006)
= 50mA (MAX15007)
10.5
11.5
12
18
19
Regulator on,
measured at GND
Ground Current
I
µA
µA
GND
20
13
21
90
150
150
5
93
Shutdown Supply Current
REGULATOR
I
Regulator off (MAX15007 only)
3
SHDN
Guaranteed Output Current
I
V
≥ V
+ ΔV
DO
50
mA
V
OUT
IN
OUT
MAX15006A/MAX15007A
MAX15006B/MAX15007B
3.25
4.925
3.3
5.0
30
3.35
5.075
53
Output Voltage
V
I
= 1mA (Note 2)
OUT
OUT
I
I
I
= 5mA, MAX15006B/MAX15007B
= 50mA, MAX15006B/MAX15007B
= 50mA, MAX15006A/MAX15007A
OUT
OUT
OUT
Dropout Voltage (Notes 3, 4)
ΔV
300
525
700
0.25
1.5
mV
DO
Line Regulation
Load Regulation
6V ≤ V ≤ 35V, I
= 1mA
%
%
IN
OUT
V
= V
+ 3V, I = 100µA to 50mA
OUT
0.7
IN
OUT
2
_______________________________________________________________________________________
40V, Ultra-Low Quiescent-Current
Linear Regulators in 6-Pin TDFN/8-Pin SO
6/MAX1507
ELECTRICAL CHARACTERISTICS (continued)
(V = 14V, I
= 1mA, C = 0.1µF, C
= 2.2µF, T = T = -40°C to +125°C, unless otherwise noted. Typical specifications are
OUT A J
IN
OUT
IN
at T = +25°C.) (Note 1)
A
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Output Current Limit
80
350
mA
V
V
= 3.3V
= 5V
115
179
66
OUT
OUT
100Hz to 100kHz, I
OUT
Output Voltage Noise
µV
RMS
= 50mA, C
= 2.2µF
OUT
Power-Supply Rejection Ratio
PSRR
f = 100Hz, V
= 500mV , I
= 50mA
dB
IN_RIPPLE
P-P OUT
ENABLE LOGIC
V
0.4
2
IL
Enable Threshold Voltage
V
V
1.4
IH
Enable Threshold Hysteresis
Enable Pulldown Current
Enable to Regulation Time
THERMAL SHUTDOWN
Thermal Shutdown
60
0.5
0.4
mV
µA
ms
Internally pulled down to GND
(Note 5)
T
Junction temperature rising
+165
20
°C
°C
SHDN
Thermal Shutdown Hysteresis
T
HYST
Note 1: Limits at -40°C are guaranteed by design.
Note 2: Output voltage regulation is guaranteed for I
≥ 5µA.
OUT
Note 3: Dropout voltage is defined as (V - V
) when V
is 2% below the value of V
when V = V
+ 3V.
OUT
IN
OUT
OUT
OUT
IN
Note 4: For V
= 3.3V, the 700mV dropout indicates V
does not reach 2% below V
at V = V
+ 3V at minimum 4V
OUT
OUT
OUT
IN
OUT
input voltage.
Note 5: Enable to regulation time is the time the output takes to reach 95% of its final value with V = 14V and EN is taken from V
IN
IL
to V in 5ns.
IH
_______________________________________________________________________________________
3
40V, Ultra-Low Quiescent-Current
Linear Regulators in 6-Pin TDFN/8-Pin SO
Typical Operating Characteristics
(V = 14V, C = 0.1µF, C
= 2.2µF, V = V , T = +25°C, unless otherwise noted.)
IN
IN
OUT
EN
IN
A
OUTPUT VOLTAGE vs. INPUT VOLTAGE
(MAX15006A/MAX15007A)
OUTPUT VOLTAGE vs. INPUT VOLTAGE
(MAX15006B/MAX15007B)
OUTPUT VOLTAGE vs. TEMPERATURE
(MAX15006A/MAX15007A)
3.6
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
3.45
3.42
3.39
3.36
3.33
3.30
3.27
3.24
3.21
3.18
3.15
3.3
3.0
2.7
2.4
2.1
1.8
1.5
1.2
0.9
0.6
0.3
0
I
= 1mA
OUT
I
= 50mA
OUT
I
= 0
I
= 0
OUT
OUT
0
5
10 15 20 25 30 35 40
(V)
0
5
10 15 20 25 30 35 40
(V)
-50 -25
0
25 50 75 100 125 150
V
V
TEMPERATURE (°C)
IN
IN
6/MAX1507
OUTPUT VOLTAGE vs. TEMPERATURE
(MAX15006B/MAX15007B)
DROPOUT VOLTAGE vs. LOAD CURRENT
(MAX15006B/MAX15007B)
GROUND CURRENT vs. LOAD CURRENT
(MAX15006B/MAX15007B)
5.25
5.20
5.15
5.10
5.05
5.00
4.95
4.90
4.85
4.80
4.75
500
450
400
350
300
250
200
150
100
50
100
90
80
70
60
50
40
30
20
10
0
T
= +125°C
A
T
= +125°C
A
I
= 1mA
OUT
T
= +25°C
A
T
= +25°C
A
T
= -40°C
A
T
= -40°C
A
I
= 50mA
OUT
0
-50 -25
0
25 50 75 100 125 150
0
5
10 15 20 25 30 35 40 45 50
(mA)
0
5
10 15 20 25 30 35 40 45 50
(mA)
TEMPERATURE (°C)
I
OUT
I
OUT
GROUND CURRENT vs. TEMPERATURE
GROUND CURRENT vs. TEMPERATURE
(I = 50mA)
SHUTDOWN SUPPLY CURRENT
vs. TEMPERATURE
(I
OUT
= 0)
OUT
18
16
14
12
10
8
100
99
98
97
96
95
94
93
92
91
90
10
9
8
7
6
5
4
3
2
1
0
V
= +40V
IN
V
= +14V
V
IN
V
= +40V
IN
= +6V
IN
V
= +14V
IN
6
V
= +6V
IN
4
2
0
-50 -25
0
25 50 75 100 125 150
-50 -25
0
25 50 75 100 125 150
-50 -25
0
25 50 75 100 125 150
TEMPERATURE (°C)
TEMPERATURE (°C)
TEMPERATURE (°C)
4
_______________________________________________________________________________________
40V, Ultra-Low Quiescent-Current
Linear Regulators in 6-Pin TDFN/8-Pin SO
6/MAX1507
Typical Operating Characteristics (continued)
(V = 14V, C = 0.1µF, C
= 2.2µF, V = V , T = +25°C, unless otherwise noted.)
IN
IN
OUT
EN
IN
A
GROUND CURRENT DISTRIBUTION
GROUND CURRENT DISTRIBUTION
GROUND CURRENT DISTRIBUTION
(T = -40°C)
A
(T = +125°C)
A
(T = +25°C)
A
27
24
21
18
15
12
9
27
24
21
18
15
12
9
27
MAX15007, I
= 0
OUT
MAX15007, I
= 0
MAX15007, I
= 0
OUT
OUT
24
21
18
15
12
9
50 UNITS TESTED
50 UNITS TESTED
50 UNITS TESTED
6
6
6
3
3
3
0
0
0
10.4 10.5 10.6 10.7 10.8 10.9 11.0
11.8
I
11.6 11.7
11.9 12.0 12.1
10.8 10.9 11.0 11.1 11.2 11.3 11.4
I
(μA)
(μA)
GND
I
(μA)
GND
GND
LOAD-TRANSIENT RESPONSE
(MAX15006B/MAX15007B)
INPUT-VOLTAGE STEP RESPONSE
(MAX15006B/MAX15007B, I
= 1mA)
OUT
STARTUP RESPONSE
MAX15006 toc15
MAX15006 toc13
MAX15006 toc14
18V
V
OUT
V
IN
V
IN
5V/div
AC-COUPLED
200mV/div
14V
50mA
V
OUT
I
OUT
V
OUT
AC-COUPLED
100mV/div
1mA
2V/div
MAX15006B/MAX15007B
= 1mA
I
OUT
400μs/div
400μs/div
200μs/div
ENABLE STARTUP RESPONSE
ENABLE STARTUP RESPONSE
MAX15006 toc17
ENABLE STARTUP RESPONSE
MAX15006 toc16
MAX15006 toc18
EN
EN
EN
1V/div
1V/div
1V/div
V
OUT
V
OUT
V
OUT
2V/div
2V/div
2V/div
MAX15006B/MAX15007B
= 0
MAX15006B/MAX15007B
I = 50mA
OUT
MAX15006B/MAX15007B
= 40V, I = 0
I
V
OUT
IN
OUT
400μs/div
400μs/div
400μs/div
_______________________________________________________________________________________
5
40V, Ultra-Low Quiescent-Current
Linear Regulators in 6-Pin TDFN/8-Pin SO
Typical Operating Characteristics (continued)
(V = 14V, C = 0.1µF, C
= 2.2µF, V = V , T = +25°C, unless otherwise noted.)
EN IN A
IN
IN
OUT
POWER-SUPPLY REJECTION RATIO
vs. FREQUENCY
OUTPUT-NOISE SPECTRAL DENSITY
vs. FREQUENCY
ENABLE STARTUP RESPONSE
MAX15006 toc19
0
10
1
I
= 50mA
OUT
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
EN
1V/div
C
= 2.2μF
OUT
0.1
0.01
V
OUT
2V/div
C
= 10μF
OUT
1
MAX15006B/MAX15007B
= 40V, I = 50mA
MAX15006A/MAX15007A
V
IN
OUT
I
= 50mA
OUT
0.01
0.1
10
100
1000
400μs/div
0.01
0.1
1
10
100
FREQUENCY (kHz)
FREQUENCY (kHz)
6/MAX1507
OUTPUT-NOISE SPECTRAL DENSITY
vs. FREQUENCY
OUTPUT VOLTAGE NOISE
vs. LOAD CURRENT
10
1
150
135
120
105
90
75
60
45
30
15
0
0.1
MAX15006B/MAX15007B
I
= 50mA
OUT
MAX15006A/MAX15007A
10 15 20 25 30 35 40 45 50
(mA)
0.01
0.01
0.1
1
10
100
0
5
FREQUENCY (kHz)
I
OUT
6
_______________________________________________________________________________________
40V, Ultra-Low Quiescent-Current
Linear Regulators in 6-Pin TDFN/8-Pin SO
6/MAX1507
Typical Operating Characteristics (continued)
(V = 14V, C = 0.1µF, C
= 2.2µF, V = V , T = +25°C, unless otherwise noted.)
EN IN A
IN
IN
OUT
OUTPUT VOLTAGE NOISE
vs. OUTPUT CAPACITANCE
CLAMPED LOAD DUMP
(I = 0)
OUT
MAX15006 toc25
150
135
120
105
90
40V
V
IN
13.5V
75
60
45
V
OUT
AC-COUPLED
20mV/div
30
MAX15006A/MAX15007A
= 25mA
15
I
OUT
0
0
2
4
6
8
10 12 14 16 18 20 22
(μF)
100ms/div
C
OUT
Pin Description
PIN
NAME
FUNCTION
MAX15006
MAX15007
TDFN
SO
TDFN
SO
Regulator Supply Input. Supply voltage ranges from 4V to 40V. Bypass
with a 0.1µF capacitor to GND.
1, 2
1
1, 2
1
IN
2, 3,
4, 6, 7
3
4
—
4
2, 4, 6, 7
N.C.
GND
OUT
No Connection. Not internally connected.
Ground
5
5
8
Regulator Output. Bypass OUT to GND with a low-ESR capacitor with a
minimum 2.2µF.
5, 6
8
5, 6
Active-High Enable Input. Force EN high (or connect to V ) to turn the
IN
regulator on. Pull EN low (or leave unconnected) to place the device in a
low-power shutdown mode. EN is internally pulled down to GND through a
0.5µA sink current.
—
—
3
3
EN
EP
Exposed Pad. Internally connected to GND. Connect EP to the ground
plane for enhanced thermal performance. Do not use EP as a ground
connection.
EP
EP
EP
EP
_______________________________________________________________________________________
7
40V, Ultra-Low Quiescent-Current
Linear Regulators in 6-Pin TDFN/8-Pin SO
Functional Diagrams
IN
-
FET DRIVER
WITH
CURRENT LIMIT
+
OUT
ERROR
AMPLIFIER
THERMAL
SENSOR
1.242V
REF
GND
6/MAX1507
MAX15006
Figure 1. MAX15006 Simplified Functional Diagram
IN
CONTROL
LOGIC
-
FET DRIVER
WITH
CURRENT LIMIT
EN
+
OUT
ERROR
AMPLIFIER
THERMAL
SENSOR
1.242V
REF
GND
MAX15007
Figure 2. MAX15007 Simplified Functional Diagram
8
_______________________________________________________________________________________
40V, Ultra-Low Quiescent-Current
Linear Regulators in 6-Pin TDFN/8-Pin SO
6/MAX1507
state driver in high-impedance mode, or an open-drain
Detailed Description
driver. While in shutdown, the device consumes only
The MAX15006/MAX15007 high-voltage linear regula-
3µA (typ). EN withstands voltages up to 40V, allowing it
to be driven by high input level voltages or connected
to IN for always-on operation.
tors operate over a 4V to 40V input voltage range.
These devices guarantee 50mA load drive, and offer
preset output voltages of +3.3V or +5V. Thermal shut-
down and short-circuit protection prevent damage dur-
ing overtemperature and overcurrent conditions. The
MAX15007 includes an enable input (EN) allowing the
regulators to be turned on/off using a logic-level volt-
age. Driving EN high turns on the device while driving
EN low places the device in a low-power shutdown
mode. In shutdown, the supply current is reduced to
3µA (typ). The MAX15006/MAX15007 operate over the
-40°C to +125°C automotive temperature range. All
devices are available in thermally enhanced 6-pin
TDFN and 8-pin SO packages capable of dissipating
Thermal Protection
When the junction temperature exceeds +165°C, an
internal thermal sensor turns the pass transistor off, and
allows the device to cool. The thermal sensor turns the
pass transistor on again after the junction temperature
cools by 20°C. This results in a cycled output during
continuous thermal-overload conditions. Thermal pro-
tection protects the MAX15006/MAX15007 in the event
of fault conditions. Operation at T = +150°C without
J
going into thermal shutdown is not guaranteed. Use
Figures 3a and 3b to determine the minimum guaran-
teed output current.
1.904W and 1.860W at T = +70°C, respectively.
A
Regulator
Output Short-Circuit Current Limit
The MAX15006/MAX15007 feature a 175mA current
limit. The output can be shorted to GND for an indefi-
nite period of time without damage to the device.
During a short circuit, the power dissipated across the
pass transistor can quickly heat the device. When the
die temperature reaches +165°C, the MAX15006/
MAX15007 shut down and automatically restart after
the die temperature cools by 20°C.
The regulator accepts an input voltage from 4V to 40V.
The MAX15006A/MAX15007A have a fixed 3.3V output
voltage while the MAX15006B/MAX15007B offer a fixed
5V output voltage.
EN Input (MAX15007 Only)
EN is an active-high, logic-level enable input that turns
the device on or off. Drive EN high to turn the device
on. An internal 0.5µA pulldown current keeps the
MAX15007 in shutdown mode when driven by a three-
55
55
V
= 18V, V
= 5V
V
= 18V, V
= 5V
OUT
IN
OUT
IN
50
45
40
35
30
25
20
15
10
5
50
45
40
35
30
25
20
15
10
5
V
V
= 18V,
V
V
= 18V,
IN
IN
= 3.3V
= 3.3V
OUT
OUT
V
= 26V, V
= 5V
IN
OUT
V
= 26V, V
= 5V
OUT
IN
V
= 26V, V
= 3.3V
OUT
V
= 26V, V
= 3.3V
OUT
IN
IN
0
0
80 85 90 95 100 105 110 115 120 125 130
80 85 90 95 100 105 110 115 120 125 130
AMBIENT TEMPERATURE (°C)
AMBIENT TEMPERATURE (°C)
Figure 3a. Minimum Output Current vs. Ambient Temperature
(6-Pin TDFN-EP)
Figure 3b. Minimum Output Current vs. Ambient Temperature
(8-Pin SO-EP)
_______________________________________________________________________________________
9
40V, Ultra-Low Quiescent-Current
Linear Regulators in 6-Pin TDFN/8-Pin SO
For the SO-EP package:
Applications Information
Available Output Current Calculation
1.8605W for T
≤ + 70°C
⎧
⎫
⎪
⎬
A
⎪
The MAX15006/MAX15007 provide up to 50mA of con-
tinuous output current. The input voltage range extends
to 40V. Package power dissipation limits the amount of
output current available for a given input/output voltage
and ambient temperature. Figure 4 shows the maximum
allowable power dissipation for these devices to keep the
junction temperature below +150°C. Figure 4 assumes
that the exposed metal pad of the MAX15006/MAX15007
P
=
⎨
W
°C
D
1.8605W − 0.0233
x
T
– 70°C for + 70°C
<
T
≤ +125°C
A
(
)
A
⎪
⎪
⎩
⎭
After determining the allowable package dissipation,
calculate the maximum allowable output current, with-
out exceeding the +150°C junction temperature, using
the following formula:
2
is soldered to 1in of PCB copper.
P
D
I
=
≤ 50mA
OUT(MAX)
V
− V
OUT
IN
The above equations do not include the negligible
power dissipation from self-heating due to the IC
ground current.
2.4
1.9408W
2.2
(6-PIN TDFN)
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
DERATE
23.8mW/°C
1.8605W
(8-PIN SO-EP)
Example 1 (TDFN Package):
T = +125°C
A
V
IN
V
OUT
= 26V
6/MAX1507
DERATE
23.3mW/°C
= 3.3V
Calculate the maximum allowable package dissipation
at the given temperature as follows:
W
°C
P
= 1.9048W − 0.0238
125°C − 70°C = 595.8mW
(
)
D
0
20
60 80 100
140
40
120
TEMPERATURE (°C)
And establish the maximum output current:
595.8mW
Figure 4. Calculated Maximum Power Dissipation vs. Ambient
Temperature
I
=
= 26.2mA
OUT(MAX)
26V− 3.3V
Example 2 (TDFN Package):
T = +85°C
Use Figure 4 to determine the allowable package dissi-
pation for a given ambient temperature. Alternately, use
the following formulas to calculate the allowable pack-
age dissipation. For the TDFN package:
A
V
V
= 14V
IN
OUT
= 5V
Calculate the maximum allowable package dissipation
at the given temperature as follows:
1.9048W for T
≤ + 70°C
⎧
⎫
⎪
⎬
A
⎪
P
=
⎨
W
D
1.9048W − 0.0238
x
T
– 70°C for + 70°C
<
T
≤ +125°C
A
(
)
A
⎪
⎪
W
°C
⎩
⎭
P
= 1.9048W − 0.0238
85°C − 70°C = 1.5478W
(
)
D
°C
10 ______________________________________________________________________________________
40V, Ultra-Low Quiescent-Current
Linear Regulators in 6-Pin TDFN/8-Pin SO
6/MAX1507
Then determine the maximum output current:
Alternately, use Figures 5a and 5b to quickly determine
the maximum allowable output current for selected
ambient temperatures and input voltages.
1.5478W
14V−5V
I
=
= 172mA ⇒ I
= 50mA
OUT(MAX)
OUT(MAX)
Output-Capacitor Selection
and Regulator Stability
Example 3 (TDFN Package):
T = +50°C
For stable operation over the full temperature range
and with load currents up to 50mA, use a low-ESR
2.2µF (min) ceramic or tantalum output capacitor. Use
larger output-capacitor values such as 22µF to reduce
noise, improve load-transient response, and power-
supply rejection.
A
V
IN
V
OUT
= 9V
= 5V
Calculate the maximum allowable package dissipation
at the given temperature as follows:
P = 1.9048W
D
Some ceramic dielectrics exhibit large capacitance
and ESR variations with temperature. Ensure the mini-
mum capacitance under worst-case conditions does
not drop below 1.3µF to ensure output stability. With an
X7R dielectric, 2.2µF should be sufficient at all operat-
ing temperatures.
Find the maximum output current:
1.9048W
9V−5V
I
=
= 476mA ⇒ I
= 50mA
OUT(MAX)
OUT(MAX)
In Examples 2 and 3, the maximum output current is
calculated as 172mA and 476mA, respectively; howev-
er, the allowable output current cannot exceed 50mA.
60
55
50
45
60
55
50
45
T
= +70°C
T = +70°C
A
A
40
35
30
25
20
15
10
5
40
35
30
25
20
15
10
5
T
= +85°C
A
T = +85°C
A
T
= +125°C
A
T = +125°C
A
V
= 5V
6-PIN TDFN
V
= 5V
OUT
8-PIN SO-EP
OUT
0
0
0
5
10 15 20 25 30 35 40
(V)
0
5
10 15 20 25 30 35 40
(V)
V
V
IN
IN
Figure 5a. Calculated Maximum Output Current vs. Input
Voltage (6-Pin TDFN-EP)
Figure 5b. Calculated Maximum Output Current vs. Input
Voltage (8-Pin SO-EP)
______________________________________________________________________________________ 11
40V, Ultra-Low Quiescent-Current
Linear Regulators in 6-Pin TDFN/8-Pin SO
Selector Guide
FIXED OUTPUT
VOLTAGE (V)
PART
ENABLE INPUT
TOP MARK
PIN-PACKAGE
MAX15006AASA+
MAX15006AATT+
MAX15006BASA+
MAX15006BATT+
MAX15007AASA+
MAX15007AATT+
MAX15007BASA+
MAX15007BATT+
—
—
—
—
√
3.3
3.3
5
—
APE
—
8 SO-EP
6 TDFN-EP
8 SO-EP
5
APF
—
6 TDFN-EP
8 SO-EP
3.3
3.3
5
√
APG
—
6 TDFN-EP
8 SO-EP
√
√
5
APH
6 TDFN-EP
Pin Configurations (continued)
TOP VIEW
6/MAX1507
OUT
6
OUT
5
GND
4
MAX15007A
MAX15007B
+
IN
N.C.
EN
1
2
3
4
8
7
6
5
OUT
N.C.
N.C.
GND
MAX15007A
MAX15007B
*EP
N.C.
*EP
+
SO
1
2
3
IN
IN
EN
*EXPOSED PAD
TDFN
Ordering Information (continued)
Chip Information
PROCESS: BiCMOS
PIN-
TOP
PKG
PART
PACKAGE
MARK
CODE
MAX15007AASA+ 8 SO-EP*
MAX15007AATT+ 6 TDFN-EP*
MAX15007BASA+ 8 SO-EP*
MAX15007BATT+ 6 TDFN-EP*
—
APG
—
S8E-12
T633-2
S8E-12
T633-2
APH
Note: All devices are specified over the -40°C to +125°C oper-
ating temperature range.
+Denotes lead-free package.
*EP = Exposed pad.
12 ______________________________________________________________________________________
40V, Ultra-Low Quiescent-Current
Linear Regulators in 6-Pin TDFN/8-Pin SO
6/MAX1507
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
PACKAGE OUTLINE, 6,8,10 & 14L,
TDFN, EXPOSED PAD, 3x3x0.80 mm
1
H
21-0137
2
______________________________________________________________________________________ 13
40V, Ultra-Low Quiescent-Current
Linear Regulators in 6-Pin TDFN/8-Pin SO
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
PACKAGE VARIATIONS
COMMON DIMENSIONS
MIN. MAX.
SYMBOL
PKG. CODE
T633-1
N
6
D2
1.50±0.10 2.30±0.10 0.95 BSC
1.50±0.10 2.30±0.10
E2
e
JEDEC SPEC
MO229 / WEEA
MO229 / WEEA
MO229 / WEEC
MO229 / WEEC
MO229 / WEEC
b
[(N/2)-1] x e
1.90 REF
1.90 REF
1.95 REF
1.95 REF
1.95 REF
2.00 REF
2.00 REF
2.40 REF
2.40 REF
0.40±0.05
0.40±0.05
0.30±0.05
0.30±0.05
0.30±0.05
A
0.70
2.90
2.90
0.00
0.20
0.80
3.10
3.10
0.05
0.40
T633-2
6
D
E
0.95 BSC
T833-1
8
1.50±0.10 2.30±0.10 0.65 BSC
1.50±0.10 2.30±0.10 0.65 BSC
1.50±0.10 2.30±0.10 0.65 BSC
T833-2
8
A1
L
T833-3
8
T1033-1
T1033-2
T1433-1
T1433-2
10
10
14
14
1.50±0.10 2.30±0.10 0.50 BSC MO229 / WEED-3 0.25±0.05
k
0.25 MIN.
0.20 REF.
1.50±0.10 2.30±0.10
0.25±0.05
0.20±0.05
0.20±0.05
A2
0.50 BSC MO229 / WEED-3
1.70±0.10 2.30±0.10 0.40 BSC
1.70±0.10 2.30±0.10 0.40 BSC
- - - -
- - - -
6/MAX1507
PACKAGE OUTLINE, 6,8,10 & 14L,
TDFN, EXPOSED PAD, 3x3x0.80 mm
2
-DRAWING NOT TO SCALE-
H
21-0137
2
14 ______________________________________________________________________________________
40V, Ultra-Low Quiescent-Current
Linear Regulators in 6-Pin TDFN/8-Pin SO
6/MAX1507
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
PACKAGE OUTLINE
8L SOIC, .150" EXPOSED PAD
1
21-0111
C
1
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 15
© 2006 Maxim Integrated Products
is a registered trademark of Maxim Integrated Products, Inc.
Heaney
相关型号:
MAX15006BATT+T
Fixed Positive LDO Regulator, 5V, 0.053V Dropout, BICMOS, PDSO6, 3 X 3 MM, ROHS COMPLIANT, TDFN-6
MAXIM
©2020 ICPDF网 联系我们和版权申明