MAX1265AEEI+T [MAXIM]
ADC, Successive Approximation, 12-Bit, 1 Func, 6 Channel, Parallel, Word Access, PDSO28, 0.150 INCH, 0.025 INCH PITCH, MO-137, QSOP-28;型号: | MAX1265AEEI+T |
厂家: | MAXIM INTEGRATED PRODUCTS |
描述: | ADC, Successive Approximation, 12-Bit, 1 Func, 6 Channel, Parallel, Word Access, PDSO28, 0.150 INCH, 0.025 INCH PITCH, MO-137, QSOP-28 光电二极管 转换器 |
文件: | 总19页 (文件大小:300K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
19-2721; Rev 0; 04/03
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
General Description
Features
The MAX1265/MAX1267 low-power, 12-bit analog-to-
digital converters (ADCs) feature a successive-approxi-
mation ADC, automatic power-down, fast wake-up
(2µs), an on-chip clock, +2.5V internal reference, and a
high-speed 12-bit parallel interface. They operate with
a single +2.7V to +3.6V analog supply.
o 12-Bit Resolution, ±±0. ꢀLB ꢀineꢁaitꢂ
o +3V Lingle-Lupplꢂ Opeaꢁtion
o Inteanꢁl +20.V Refeaence
o Loftwꢁae-Configuaꢁble Anꢁlog Input Multiplexea
6-Chꢁnnel Lingle Ended/
Power consumption is only 5.4mW at the maximum
sampling rate of 265ksps. Two software-selectable
power-down modes enable the MAX1265/MAX1267 to
be shut down between conversions; accessing the par-
allel interface returns them to normal operation.
Powering down between conversions can reduce sup-
ply current below 10µA at lower sampling rates.
3-Chꢁnnel Pseudo Diffeaentiꢁl (MAX126.)
2-Chꢁnnel Lingle Ended/
1-Chꢁnnel Pseudo Diffeaentiꢁl (MAX1267)
o Loftwꢁae-Configuaꢁble Unipolꢁa/Bipolꢁa
Anꢁlog Inputs
o ꢀow Cuaaent
109mA (26.ksps)
10±mA (1±±ksps)
4±±µA (1±ksps)
2µA (Lhutdown)
o Inteanꢁl 3MHz Full-Powea Bꢁndwidth Taꢁck/Hold
o Pꢁaꢁllel 12-Bit Inteafꢁce
Both devices offer software-configurable analog inputs
for unipolar/bipolar and single-ended/pseudo-differen-
tial operation. In single-ended mode, the MAX1265 has
six input channels and the MAX1267 has two (three
input channels and one input channel, respectively,
when in pseudo-differential mode).
Excellent dynamic performance and low power, com-
bined with ease of use and small package size, make
these converters ideal for battery-powered and data-
acquisition applications or for other circuits with demand-
ing power-consumption and space requirements. The
MAX1265 is offered in a 28-pin QSOP package, while the
MAX1267 comes in a 24-pin QSOP. For pin-compatible
+5V, 12-bit versions, refer to the MAX1266/MAX1268
data sheet.
o Lmꢁll Footpaint
28-Pin QLOP (MAX126.)
24-Pin QLOP (MAX1267)
Pin Configurations
TOP VIEW
D9
D8
D7
D6
D5
D4
D3
D2
D1
1
2
3
4
5
6
7
8
9
28 D10
27 D11
Applications
Industrial Control Systems Data Logging
26
V
DD
25 REF
24 REFADJ
23 GND
22 COM
21 CH0
20 CH1
19 CH2
18 CH3
17 CH4
16 CH5
15 CS
Energy Management
Patient Monitoring
Touch Screens
MAX1265
Data-Acquisition Systems
Ordering Information
INꢀ
TEMP RANGE PIN-PACKAGE
(ꢀLB)
PART
D0 10
INT 11
RD 12
WR 13
CLK 14
MAX126.ACEI
0°C to +70°C 28 QSOP
0°C to +70°C 28 QSOP
0.5
1
MAX1265BCEI
MAX1265AEEI -40°C to +85°C 28 QSOP
MAX1265BEEI -40°C to +85°C 28 QSOP
0.5
1
MAX1267ACEG
0°C to +70°C 24 QSOP
0°C to +70°C 24 QSOP
0.5
1
MAX1267BCEG
QLOP
MAX1267AEEG -40°C to +85°C 24 QSOP
MAX1267BEEG -40°C to +85°C 24 QSOP
0.5
1
Pin Configurations continued at end of data sheet.
Typical Operating Circuits appear at end of data sheet.
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
ABLOꢀUTE MAXIMUM RATINGL
DD
CH0–CH5, COM to GND............................-0.3V to (V
REF, REFADJ to GND.................................-0.3V to (V
Digital Inputs to GND ...............................................-0.3V to +6V
V
to GND..............................................................-0.3V to +6V
28-Pin QSOP (derate 8.0mW/°C above +70°C)..........667mW
Operating Temperature Ranges
MAX1265_C__/MAX1267_C__ ........................0°C to +70°C
MAX1265_E__/MAX1267_E__ ......................-40°C to +85°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
+ 0.3V)
+ 0.3V)
DD
DD
Digital Outputs (D0–D11, INT) to GND.......-0.3V to (V + 0.3V)
DD
Continuous Power Dissipation (T = +70°C)
A
24-Pin QSOP (derate 9.5mW/°C above +70°C)..........762mW
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
EꢀECTRICAꢀ CHARACTERILTICL
DD
(V
= +2.7V to +3.6V, COM = GND, REFADJ = V , V
= +2.5V, 4.7µF capacitor at REF pin, f
= 4.8MHz (50% duty cycle),
DD REF
CLK
T
A
= T
to T
, unless otherwise noted. Typical values are at T = +25°C.)
MIN
MAX
A
PARAMETER
LYMBOꢀ
CONDITIONL
MIN
12
TYP
MAX
UNITL
DC ACCURACY (Note 1)
Resolution
RES
INL
Bits
MAX126_A
MAX126_B
0.5
1
Relative Accuracy (Note 2)
LSB
Differential Nonlinearity
Offset Error
DNL
No missing codes overtemperature
1
LSB
LSB
4
Gain Error
(Note 3)
4
LSB
Gain Temperature Coefficient
2.0
0.2
ppm/°C
Channel-to-Channel Offset
Matching
LSB
DYNAMIC LPECIFICATIONL (f
= 50kHz, V = 2.5V , 265ksps, external f
= 4.8MHz, bipolar input mode)
IN(sine-wave)
SINAD
IN
P-P
CLK
Signal-to-Noise Plus Distortion
67
80
70
dB
dB
Total Harmonic Distortion
(Including 5th-Order Harmonic)
THD
-78
Spurious-Free Dynamic Range
Intermodulation Distortion
Channel-to-Channel Crosstalk
Full-Linear Bandwidth
SFDR
IMD
dB
dB
f
f
= 49kHz, f
= 52kHz
76
-78
250
3
IN1
IN2
= 125kHz (Note 4)
dB
IN
SINAD > 68dB
-3dB rolloff
kHz
MHz
Full-Power Bandwidth
CONVERLION RATE
External clock mode
3.3
2.5
3.2
Conversion Time (Note 5)
t
External acquisition/internal clock mode
Internal acquisition/internal clock mode
3.0
3.6
3.5
4.1
625
µs
CONV
Track/Hold Acquisition Time
Aperture Delay
t
ns
ns
ACQ
External acquisition or external clock mode
External acquisition or external clock mode
Internal acquisition/internal clock mode
50
<50
<200
Aperture Jitter
ps
External Clock Frequency
Duty Cycle
f
0.1
30
4.8
70
MHz
%
CLK
2
_______________________________________________________________________________________
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
EꢀECTRICAꢀ CHARACTERILTICL (continued)
(V
= +2.7V to +3.6V, COM = GND, REFADJ = V , V
= +2.5V, 4.7µF capacitor at REF pin, f
= 4.8MHz (50% duty cycle),
DD
DD REF
CLK
T
A
= T
to T
, unless otherwise noted. Typical values are at T = +25°C.)
MIN
MAX
A
PARAMETER
LYMBOꢀ
CONDITIONL
MIN
TYP
MAX
UNITL
ANAꢀOGINPUTL
Analog Input Voltage Range
Single Ended and Differential
(Note 6)
Unipolar, V
= 0
0
V
REF
COM
V
IN
V
bipolar, V
= V
/ 2
- V /2
REF
+ V /2
COM
REF
REF
Multiplexer Leakage Current
Input Capacitance
On-/off-leakage current, V = 0 or V
IN
0.01
12
1
µA
pF
DD
C
IN
INTERNAꢀ REFERENCE
REF Output Voltage
2.49
2.5
15
2.51
V
mA
REF Short-Circuit Current
REF Temperature Coefficient
REFADJ Input Range
TC
20
ppm/°C
mV
REF
For small adjustments
100
REFADJ High Threshold
Load Regulation (Note 7)
Capacitive Bypass at REFADJ
Capacitive Bypass at REF
EXTERNAꢀ REFERENCE AT REF
To power down the internal reference
0 to 0.5mA output load
V
- 1
V
DD
0.2
mV/mA
µF
0.01
1
4.7
10
µF
V
+
DD
REF Input Voltage Range
REF Input Current
V
V
REF
1.0
2.0
50mV
V
= 2.5V, f
= 265ksps
SAMPLE
200
300
2
REF
I
µA
REF
Shutdown mode
DIGITAꢀ INPUTL AND OUTPUTL
Input Voltage High
V
V
V
IH
Input Voltage Low
V
0.8
1
IL
Input Hysteresis
V
HYS
200
0.1
15
mV
µA
pF
V
Input Leakage Current
Input Capacitance
I
V
IN
= 0 or V
DD
IN
C
IN
OL
OH
Output Voltage Low
Output Voltage High
V
I
I
= 1.6mA
0.4
1
SINK
V
= 1mA
V
- 0.5
V
SOURCE
DD
Tri-State Leakage Current
Tri-State Output Capacitance
POWER REQUIREMENTL
Analog Supply Voltage
I
0.1
15
µA
pF
CS = V
CS = V
LEAKAGE
DD
DD
C
OUT
V
2.7
3.6
2.8
2.3
1.2
0.8
10
V
DD
Internal reference
External reference
Internal reference
External reference
2.5
1.9
0.9
0.5
2
Operating mode,
= 265ksps
f
SAMPLE
mA
Positive Supply Current
Power-Supply Rejection
I
DD
Standby mode
Shutdown mode
µA
PSR
V
DD
= 2.7V to 3.6V, full-scale input
0.4
0.9
mV
_______________________________________________________________________________________
3
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
TIMING CHARACTERILTICL
DD
(V
= +2.7V to +3.6V, COM = GND, REFADJ = V , V
= +2.5V, 4.7µF capacitor at REF pin, f
= 4.8MHz (50% duty cycle),
DD REF
CLK
T
A
= T
to T
, unless otherwise noted. Typical values are at T = +25°C.)
MIN
MAX
A
PARAMETER
LYMBOꢀ
CONDITIONL
MIN
TYP
MAX
UNITL
ns
CLK Period
t
208
40
40
40
0
CP
CH
CLK Pulse Width High
t
ns
CLK Pulse Width Low
t
ns
CL
DS
t
t
ns
Data Valid to WR Rise Time
WR Rise to Data Valid Hold Time
WR to CLK Fall Setup Time
CLK Fall to WR Hold Time
CS to CLK or WR Setup Time
CLK or WR to CS Hold Time
CS Pulse Width
ns
DH
t
t
40
40
60
0
ns
CWS
ns
CWH
t
ns
CSWS
t
ns
CSWH
t
100
60
20
20
20
ns
CS
t
(Note 8)
ns
WR Pulse Width
WR
t
TC
C
LOAD
C
LOAD
C
LOAD
C
LOAD
C
LOAD
= 20pF, Figure 1
100
70
ns
CS Rise to Output Disable
RD Rise to Output Disable
RD Fall to Output Data Valid
RD Fall to INT High Delay
CS Fall to Output Data Valid
t
TR
= 20pF, Figure 1
= 20pF, Figure 1
= 20pF, Figure 1
= 20pF, Figure 1
ns
t
70
ns
DO
t
100
110
ns
INT1
t
ns
DO2
Note 1: Tested at V
= +3V, COM = GND, unipolar single-ended input mode.
DD
Note 2: Relative accuracy is the deviation of the analog value at any code from its theoretical value after offset and gain errors have
been removed.
Note 3: Offset nulled.
Note 4: On channel is grounded; sine wave applied to off channels.
Note .: Conversion time is defined as the number of clock cycles times the clock period; clock has a 50% duty cycle.
Note 6: Input voltage range referenced to negative input. The absolute range for the analog inputs is from GND to V
Note 7: External load should not change during conversion for specified accuracy.
.
DD
Note 8: When bit 5 is set low for internal acquisition, WR must not return low until after the first falling clock edge of the conversion.
V
DD
DOUT
3kΩ
C
LOAD
20pF
6kΩ
DOUT
C
LOAD
20pF
a) HIGH-Z TO V AND V TO V
OH
b) HIGH-Z TO V AND V TO V
OL
OH
OL
OL
OH
Figure 1. Load Circuits for Enable/Disable Times
4
_______________________________________________________________________________________
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
Typical Operating Characteristics
(V
= +3V, V
= +2.500V, f
= 4.8MHz, C = 20pF, T = +25°C, unless otherwise noted.)
DD
REF
CLK
L
A
DIFFERENTIAL NONLINEARITY
vs. DIGITAL OUTPUT CODE
INTEGRAL NONLINEARITY
vs. DIGITAL OUTPUT CODE
SUPPLY CURRENT
vs. SAMPLE FREQUENCY
0.5
0.4
0.5
10,000
1000
100
10
0.4
0.3
0.3
WITH INTERNAL REFERENCE
0.2
0.2
0.1
0.1
0
0
-0.1
-0.2
-0.3
-0.4
-0.5
-0.1
-0.2
-0.3
-0.4
-0.5
WITH EXTERNAL REFERENCE
0
0
1000
2000
3000
4000
5000
1k
0
1000
2000
3000
4000
5000
0.1
1
10
100
10k 100k 1M
DIGITAL OUTPUT CODE
DIGITAL OUTPUT CODE
f
(Hz)
SAMPLE
SUPPLY CURRENT vs. SUPPLY VOLTAGE
STANDBY CURRENT vs. SUPPLY VOLTAGE
SUPPLY CURRENT vs. TEMPERATURE
2.10
2.05
2.00
1.95
1.90
1.85
1.80
930
920
910
900
890
880
2.2
2.1
2.0
1.9
1.8
1.7
1.6
R = ∞
R = ∞
L
L
CODE = 101010100000
CODE = 101010100000
2.7
3.0
3.3
3.6
2.7
3.0
3.3
3.6
-40
-15
10
35
60
85
V
(V)
V
(V)
DD
TEMPERATURE (°C)
DD
STANDBY CURRENT
vs. TEMPERATURE
POWER-DOWN CURRENT
vs. TEMPERATURE
POWER-DOWN CURRENT
vs. SUPPLY VOLTAGE
1.2
1.1
1.0
0.9
0.8
930
920
910
900
890
880
1.50
1.25
1.00
0.75
0.50
-40
-15
10
35
60
85
-40
-15
10
35
60
85
2.7
3.0
3.3
3.6
TEMPERATURE (°C)
TEMPERATURE (°C)
V
DD
(V)
_______________________________________________________________________________________
.
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
Typical Operating Characteristics (continued)
(V
= +3V, V
= +2.500V, f
= 4.8MHz, C = 20pF, T = +25°C, unless otherwise noted.)
DD
REF
CLK
L
A
INTERNAL REFERENCE VOLTAGE
vs. TEMPERATURE
INTERNAL REFERENCE VOLTAGE
vs. SUPPLY VOLTAGE
OFFSET ERROR vs. SUPPLY VOLTAGE
2.53
0
-0.5
-1.0
-1.5
-2.0
-2.5
2.53
2.52
2.51
2.50
2.49
2.48
2.52
2.51
2.50
2.49
2.48
-40
-15
10
35
60
85
3.0
3.3
2.7
3.0
3.3
3.6
2.7
3.6
TEMPERATURE (°C)
V
(V)
V
(V)
DD
DD
OFFSET ERROR vs. TEMPERATURE
GAIN ERROR vs. SUPPLY VOLTAGE
GAIN ERROR vs. TEMPERATURE
0.5
0
1.0
0
0.5
0
-0.5
-1.0
-1.5
-2.0
-2.5
-0.5
-1.0
-1.5
-2.0
-1.0
-2.0
-3.0
-40
-15
10
35
60
85
-40
-15
10
35
60
85
2.7
3.0
3.3
3.6
TEMPERATURE (°C)
V
(V)
TEMPERATURE (°C)
DD
FFT PLOT
20
0
V
f
= 3V
DD
= 50kHz
IN
f
= 250ksps
SAMPLE
-20
-40
-60
-80
-100
-120
-140
0
200
400
600
800
1000
FREQUENCY (kHz)
6
_______________________________________________________________________________________
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
Pin Description
PIN
NAME
FUNCTION
MAX126.
MAX1267
1
2
1
2
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
INT
Tri-State Digital Output (D9)
Tri-State Digital Output (D8)
Tri-State Digital I/O Line (D7)
Tri-State Digital I/O Line (D6)
Tri-State Digital I/O Line (D5)
Tri-State Digital I/O Line (D4)
Tri-State Digital I/O Line (D3)
Tri-State Digital I/O Line (D2)
Tri-State Digital I/O Line (D1)
Tri-State Digital I/O Line (D0)
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
11
10
11
INT goes low when the conversion is complete and output data is ready.
Active-Low Read Select. If CS is low, a falling edge on RD enables the read opera-
tion on the data bus.
12
12
RD
Active-Low Write Select. When CS is low in the internal acquisition mode, a rising
edge on WR latches in configuration data and starts an acquisition plus a conver-
sion cycle. When CS is low in external acquisition mode, the first rising edge on WR
ends acquisition and starts a conversion.
13
13
WR
Clock Input. In external clock mode, drive CLK with a TTL-/CMOS-compatible clock.
14
15
14
15
CLK
In internal clock mode, connect this pin to either V
or GND.
DD
Active-Low Chip Select. When CS is high, digital outputs (D11–D0) are high
impedance.
CS
16
17
18
19
20
21
—
—
—
—
16
17
CH5
CH4
CH3
CH2
CH1
CH0
Analog Input Channel 5
Analog Input Channel 4
Analog Input Channel 3
Analog Input Channel 2
Analog Input Channel 1
Analog Input Channel 0
Ground Reference for Analog Inputs. Sets zero-code voltage in single-ended mode
and must be stable to 0.5 LSB during conversion.
22
23
18
19
COM
GND
Analog and Digital Ground
Bandgap Reference Output/Bandgap Reference Buffer Input. Bypass to GND with
24
20
REFADJ
a 0.01µF capacitor. When using an external reference, connect REFADJ to V
to
DD
disable the internal bandgap reference.
_______________________________________________________________________________________
7
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
Pin Description (continued)
PIN
NAME
FUNCTION
MAX126.
MAX1267
Bandgap Reference Buffer Output/External Reference Input. Add a 4.7µF capacitor
to GND when using the internal reference.
25
21
REF
26
27
28
22
23
24
V
Analog +2.7V to +3.6V Power Supply. Bypass with a 0.1µF capacitor to GND.
Tri-State Digital Output (D11)
DD
D11
D10
Tri-State Digital Output (D10)
REF
T/H
REFADJ
17kΩ
1.22V
REFERENCE
A =
V
2.05
(CH5)
(CH4)
(CH3)
(CH2)
CH1
ANALOG
INPUT
MULTIPLEXER
CHARGE REDISTRIBUTION
12-BIT DAC
COMP
CH0
12
COM
CLK
SUCCESSIVE-
APPROXIMATION
REGISTER
CLOCK
CS
WR
RD
CONTROL LOGIC
AND
LATCHES
MAX1265
MAX1267
INT
V
DD
12
TRI-STATE, BIDIRECTIONAL
I/O INTERFACE
GND
D0–D11
12-BIT DATA BUS
( ) ARE FOR MAX1265 ONLY.
Figure 2. Simplified Functional Diagram of 6-/2-Channel MAX1265/MAX1267
Single-Ended and
________________Detailed Description
Pseudo-Differential Operation
The sampling architecture of the ADC’s analog com-
parator is illustrated in the equivalent input circuit in
Figure 3. In single-ended mode, IN+ is internally
switched to channels CH0–CH5 for the MAX1265
(Figure 3a) and to CH0–CH1 for the MAX1267 (Figure
3b), while IN- is switched to COM (Table 2). In differen-
tial mode, IN+ and IN- are selected from analog input
pairs (Table 3) and are internally switched to either of
Converter Operation
The MAX1265/MAX1267 ADCs use a successive-
approximation (SAR) conversion technique and an input
track/hold (T/H) stage to convert an analog input signal
to a 12-bit digital output. This output format provides an
easy interface to standard microprocessors (µPs). Figure
2 shows the simplified internal architecture of the
MAX1265/MAX1267.
8
_______________________________________________________________________________________
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
the analog inputs. This configuration is pseudo-differ-
ential in that only the signal at IN+ is sampled. The
return side (IN-) must remain stable within 0.5 LSB
( 0.1 LSB for best performance) with respect to GND
during a conversion. To accomplish this, connect a
0.1µF capacitor from IN- (the selected input) to GND.
end of the acquisition interval, the T/H switch opens,
retaining charge on C
at IN+.
as a sample of the signal
HOLD
The conversion interval begins with the input multiplex-
er switching C from the positive input (IN+) to the
HOLD
negative input (IN-). This unbalances node zero at the
comparator’s positive input. The capacitive digital-to-
analog converter (DAC) adjusts during the remainder
During the acquisition interval, the channel selected as
the positive input (IN+) charges capacitor C . At the
HOLD
12-BIT CAPACITIVE DAC
12-BIT CAPACITIVE DAC
V
V
REF
REF
COMPARATOR
COMPARATOR
INPUT
INPUT
MUX
C
C
HOLD
HOLD
MUX
ZERO
ZERO
–
+
–
+
CH0
CH0
CH1
12pF
12pF
R
CH1
CH2
CH3
CH4
CH5
R
IN
IN
800Ω
800Ω
C
C
SWITCH
SWITCH
HOLD
HOLD
TRACK
TRACK
AT THE SAMPLING INSTANT,
THE MUX INPUT SWITCHES
FROM THE SELECTED IN+
CHANNEL TO THE SELECTED
IN- CHANNEL.
AT THE SAMPLING INSTANT,
THE MUX INPUT SWITCHES
FROM THE SELECTED IN+
CHANNEL TO THE SELECTED
IN- CHANNEL.
T/H
SWITCH
T/H
SWITCH
COM
COM
SINGLE-ENDED MODE: IN+ = CH0–CH5, IN- = COM
DIFFERENTIAL MODE: IN+ AND IN- SELECTED FROM PAIRS
CH0/CH1, CH2/CH3, AND CH4/CH5
SINGLE-ENDED MODE: IN+ = CH0–CH1, IN- = COM
DIFFERENTIAL MODE: IN+ AND IN- SELECTED FROM PAIR
CH0/CH1
Figure 3a. MAX1265 Simplified Input Structure
Figure 3b. MAX1267 Simplified Input Structure
Tꢁble 10 Contaol-Bꢂte Functionꢁl Descaiption
BIT
NAME
FUNCTIONAꢀ DELCRIPTION
PD1 and PD± select the various clock and power-down modes.
±
±
1
1
±
1
±
1
Full power-down mode. Clock mode is unaffected.
D7, D6
PD1, PD0
Standby power-down mode. Clock mode is unaffected.
Normal operation mode. Internal clock mode selected.
Normal operation mode. External clock mode selected.
ACQMOD = 0: Internal acquisition mode
ACQMOD = 1: External acquisition mode
D5
D4
ACQMOD
SGL/DIF = 0: Pseudo-differential analog input mode
SGL/DIF = 1: Single-ended analog input mode
In single-ended mode, input signals are referred to COM. In differential mode, the voltage difference
between two channels is measured (Tables 2 and 4).
SGL/DIF
UNI/BIP = 0: Bipolar mode
UNI/BIP = 1: Unipolar mode
In unipolar mode, an analog input signal from 0V to V
D3
UNI/BIP
can be converted; in bipolar mode, the
REF
signal can range from -V /2 to +V
REF
/2.
REF
Address bits A2, A1, A0 select which of the 6/2 (MAX1265/MAX1267) channels are to be converted
(Tables 2 and 3).
D2, D1, D0
A2, A1, A0
_______________________________________________________________________________________
9
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
Tꢁble 20 Chꢁnnel Lelection foa Lingle-Ended Opeaꢁtion (LGꢀ/DIF = 1)
A2
A1
A±
CH±
CH1
CH2*
CH3*
CH4*
CH.*
COM
0
0
0
0
1
1
0
0
1
1
0
0
0
1
0
1
0
1
+
-
-
-
-
-
-
+
+
+
+
+
*Channels CH2–CH5 apply to MAX1265 only.
Tꢁble 30 Chꢁnnel Lelection foa Pseudo-Diffeaentiꢁl Opeaꢁtion (LGꢀ/DIF = ±)
A2
0
A1
0
A±
0
CH±
CH1
CH2*
CH3*
CH4*
CH.*
+
-
-
0
0
1
+
0
1
0
+
-
-
0
1
1
+
1
0
0
+
-
-
1
0
1
+
*Channels CH2–CH5 apply to MAX1265 only.
of the conversion cycle to restore node 0 to 0V within
the limits of 12-bit resolution. This action is equivalent to
In single-ended operation, IN- is connected to COM
and the converter samples the positive (+) input. In
pseudo-differential operation, IN- connects to the nega-
transferring a 12pF (V
- V ) charge from C
to
HOLD
IN+
IN-
the binary-weighted capacitive DAC, which in turn
forms a digital representation of the analog input signal.
tive (-) input, and the difference of (IN+) - (IN-) is sam-
| |
pled. At the beginning of the next conversion, the
positive input connects back to IN+ and CHOLD
charges to the input signal.
Analog Input Protection
Internal protection diodes, which clamp the analog
The time required for the T/H stage to acquire an input
signal depends on how quickly its input capacitance is
charged. If the input signal’s source impedance is high,
the acquisition time lengthens and more time must be
allowed between conversions. The acquisition time,
input to V
and GND, allow each input channel to
DD
swing within (GND - 300mV) to (V
+ 300mV) without
DD
damage. However, for accurate conversions near full
scale, both inputs must not exceed (V
less than (GND - 50mV).
+ 50mV) or be
DD
t
, is the maximum time the device takes to acquire
ACQ
If an analog input voltage exceeds the supplies by
more than 50mV, limit the forward-bias input current to
4mA.
the signal, and is also the minimum time required for
the signal to be acquired. Calculate this with the follow-
ing equation:
Track/Hold
The MAX1265/MAX1267 T/H stage enters its tracking
mode on WR’s rising edge. In external acquisition
mode, the part enters its hold mode on the next rising
edge of WR. In internal acquisition mode, the part
enters its hold mode on the fourth falling edge of clock
after writing the control byte. Note that, in internal clock
mode, this is approximately 1µs after writing the control
byte.
t
= 9(R + R )C
S IN IN
ACQ
where R is the source impedance of the input signal,
S
R
(800Ω) is the input resistance, and C (12pF) is
IN
IN
the input capacitance of the ADC. Source impedances
below 3kΩ have no significant impact on the MAX1265/
MAX1267s’ AC performance.
Higher source impedances can be used if a 0.01µF
capacitor is connected to the individual analog inputs.
1± ______________________________________________________________________________________
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
t
CS
CS
t
ACQ
t
CONV
t
t
CSWH
CSWS
t
WR
WR
t
DH
t
DS
CONTROL
BYTE
D11–D0
ACQMOD = 0
t
INT1
INT
RD
t
t
TR
D0
HIGH-Z
HIGH-Z
VALID DATA
DOUT
Figure 4. Conversion Timing Using Internal Acquisition Mode
Together with the input impedance, this capacitor
forms an RC filter, limiting the ADC’s signal bandwidth.
for acquiring the signal: an internal and an external
acquisition. The conversion period lasts for 13 clock
cycles in either the internal or external clock or acquisi-
tion mode. Writing a new control byte during a conver-
sion cycle aborts the conversion and starts a new
acquisition interval.
Input Bandwidth
The MAX1265/MAX1267 T/H stage offers a 250kHz full-
linear and a 3MHz full-power bandwidth. This makes it
possible to digitize high-speed transients and measure
periodic signals with bandwidths exceeding the ADC’s
sampling rate by using undersampling techniques. To
avoid high-frequency signals being aliased into the fre-
quency band of interest, anti-alias filtering is recom-
mended.
Internal Acquisition
Select internal acquisition by writing the control byte
with the ACQMOD bit cleared (ACQMOD = 0). This
causes the write pulse to initiate an acquisition interval
whose duration is internally timed. Conversion starts
when this acquisition interval (three external clock
cycles or approximately 1µs in internal clock mode)
ends (Figure 4). Note that, when the internal acquisition
is combined with the internal clock, the aperture jitter
can be as high as 200ps. Internal clock users wishing
to achieve the 50ps jitter specification should always
use external acquisition mode.
Starting a Conversion
Initiate a conversion by writing a control byte that selects
the multiplexer channel and configures the MAX1265/
MAX1267 for either unipolar or bipolar operation. A
write pulse (WR + CS) can either start an acquisition
interval or initiate a combined acquisition plus conver-
sion. The sampling interval occurs at the end of the
acquisition interval. The acquisition mode (ACQMOD)
bit in the input control byte (Table 1) offers two options
______________________________________________________________________________________ 11
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
t
CS
CS
t
t
t
CONV
CSWS
ACQ
t
WR
t
t
CSWH
WR
DH
t
DS
CONTROL
BYTE
ACQMOD = 1
CONTROL
BYTE
ACQMOD = 0
D11–D0
INT
t
INT1
RD
t
D0
t
TR
HIGH-Z
HIGH-Z
VALID DATA
DOUT
Figure 5. Conversion Timing Using External Acquisition Mode
External Acquisition
Use external acquisition mode for precise control of the
sampling aperture and/or dependent control of acquisi-
tion and conversion times. The user controls acquisition
and start of conversion with two separate write pulses.
The first pulse, written with ACQMOD = 1, starts an
acquisition interval of indeterminate length. The second
write pulse, written with ACQMOD = 0 (all other bits in
control byte unchanged), terminates acquisition and
starts conversion on WR rising edge (Figure 5).
when the conversion is complete and the output data is
ready (Figures 4 and 5). It returns high on the first read
cycle or if a new control byte is written.
Selecting Clock Mode
The MAX1265/MAX1267 operate with either an internal
or an external clock. Control bits D6 and D7 select
either internal or external clock mode. The part retains
the last-requested clock mode if a power-down mode is
selected in the current input word. For both internal and
external clock mode, internal or external acquisition
can be used. At power-up, the MAX1265/MAX1267
enter the default external clock mode.
The address bits for the input multiplexer must have the
same values on the first and second write pulse.
Power-down mode bits (PD0, PD1) can assume new
values on the second write pulse (see Power-Down
Modes section). Changing other bits in the control byte
corrupts the conversion.
Internal Clock Mode
Select internal clock mode to release the µP from the
burden of running the SAR conversion clock. Bit D7 of
the control byte must be set to 1 and bit D6 must be set
to zero. The internal clock frequency is then selected,
resulting in a conversion time of 3.6µs. When using the
internal clock mode, tie the CLK pin either high or low
to prevent the pin from floating.
Reading a Conversion
A standard interrupt signal, INT, is provided to allow the
MAX1265/MAX1267 to flag the µP when the conversion
has ended and a valid result is available. INT goes low
12 ______________________________________________________________________________________
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
ACQUISITION STARTS
CONVERSION STARTS
ACQUISITION ENDS
t
CP
CLK
WR
t
t
CH
t
CWS
CL
WR GOES HIGH WHEN CLK IS HIGH.
ACQMOD = 0
ACQUISITION STARTS
t
CWH
CONVERSION STARTS
ACQUISITION ENDS
CLK
WR
ACQMOD = 0
WR GOES HIGH WHEN CLK IS LOW.
Figure 6a. External Clock and WR Timing (Internal Acquisition Mode)
ACQUISITION STARTS
ACQUISITION ENDS
CONVERSION STARTS
CLK
t
CWS
t
DH
WR
ACQMOD = 0
ACQMOD = 1
WR GOES HIGH WHEN CLK IS HIGH
ACQUISITION ENDS
ACQUISITION STARTS
CONVERSION STARTS
CLK
WR
t
CWH
t
DH
ACQMOD = 1
WR GOES HIGH WHEN CLK IS LOW
ACQMOD = 0
Figure 6b. External Clock and WR Timing (External Acquisition Mode)
External Clock Mode
To select the external clock mode, bits D6 and D7 of
the control byte must be set to 1. Figure 6 shows the
clock and WR timing relationship for internal (Figure 6a)
and external (Figure 6b) acquisition modes with an
external clock. For proper operation, a 100kHz to
4.8MHz clock frequency with 30% to 70% duty cycle is
recommended. Operating the MAX1265/MAX1267 with
clock frequencies lower than 100kHz is not recommend-
ed, because the resulting voltage droop across the hold
capacitor in the T/H stage degrades performance.
Digital Interface
The input and output data are multiplexed on a tri-state
parallel interface (I/O) that can easily be interfaced with
standard µPs. The signals CS, WR, and RD control the
write and read operations. CS represents the chip-
______________________________________________________________________________________ 13
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
Tꢁble 40 Contaol-Bꢂte Foamꢁt
D7
(MLB)
D±
(ꢀLB)
D6
D.
D4
D3
D2
D1
PD1
PD0
ACQMOD
A2
A1
A0
SGL/DIF
UNI/BIP
An internal buffer is designed to provide +2.5V at REF for
both the MAX1265 and MAX1267. The internally trimmed
+1.22V reference is buffered with a +2.05V/V gain.
V
= +3V
DD
50kΩ
50kΩ
Internal Reference
The full-scale range with the internal reference is +2.5V
with unipolar inputs and 1.25V with bipolar inputs. The
internal reference buffer allows for small adjustments
( 100mV) in the reference voltage (Figure 7).
MAX1265
MAX1267
330kΩ
REFADJ
REF
GND
0.01µF
4.7µF
Note: The reference buffer must be compensated with
an external capacitor (4.7µF min) connected between
REF and GND to reduce reference noise and switching
spikes from the ADC. To further minimize noise on the
reference, connect a 0.01µF capacitor between REFADJ
and GND.
GND
Figure 7. Reference Adjustment with External Potentiometer
select signal, which enables a µP to address the
MAX1265/MAX1267 as an I/O port. When high, CS dis-
ables the CLK, WR, and RD inputs and forces the inter-
face into a high-impedance (high-Z) state.
External Reference
With both the MAX1265 and MAX1267, an external refer-
ence can be placed at either the input (REFADJ) or the
output (REF) of the internal reference buffer amplifier.
Input Format
The control bit sequence is latched into the device on
pins D7–D0 during a write command. Table 4 shows
the control-byte format.
Using the REFADJ input makes buffering the external
reference unnecessary. The REFADJ input impedance
is typically 17kΩ.
When applying an external reference to REF, disable
the internal reference buffer by connecting REFADJ to
DD
Therefore, an external reference at REF must deliver up
to 200µA DC load current during a conversion and
have an output impedance less than 10Ω. If the refer-
ence has higher output impedance or is noisy, bypass
it close to the REF pin with a 4.7µF capacitor.
Output Data Format
The 12-bit-wide output format for both the MAX1265/
MAX1267 is binary in unipolar mode and two’s comple-
ment in bipolar mode. CS, RD, WR, INT, and the 12 bits
of output data can interface directly to a 16-bit data bus.
When reading the output data, CS and RD must be low.
V
. The DC input resistance at REF is 25kΩ.
__________Applications Information
Power-Down Modes
To save power, place the converter in a low-current
shutdown state between conversions. Select standby
mode or shutdown mode using bits D6 and D7 of the
control byte (Tables 1 and 4). In both software power-
down modes, the parallel interface remains active, but
the ADC does not convert.
Power-On Reset
When power is first applied, internal power-on reset cir-
cuitry activates the MAX1265/MAX1267 in external clock
mode and sets INT high. After the power supplies stabi-
lize, the internal reset time is 10µs; no conversions
should be attempted during this phase. When using the
internal reference, 500µs is required for V
to stabilize.
REF
Standby Mode
While in standby mode, the supply current is typically
850µA. The part powers up on the next rising edge of
WR and is ready to perform conversions. This quick
turn-on time allows the user to realize significantly
reduced power consumption for conversion rates
below 265ksps.
Internal and External Reference
The MAX1265/MAX1267 can be used with an internal
or external reference voltage. An external reference
can be connected directly to REF or REFADJ.
14 ______________________________________________________________________________________
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
Tꢁble .0 Full Lcꢁle ꢁnd Zeao Lcꢁle foa Unipolꢁa ꢁnd Bipolꢁa Opeaꢁtion
UNIPOꢀAR MODE
BIPOꢀAR MODE
Zero scale
Full scale
COM
+ COM
Zero scale
COM
Positive full scale
V
/2 + COM
REF
V
REF
Negative full scale
-V
/2 + COM
REF
OUTPUT CODE
REF
OUTPUT CODE
FULL-SCALE
TRANSITION
FS
+ COM
+ COM
=
011 . . . 111
011 . . . 110
2
FS = REF + COM
111 . . . 111
ZS = COM
111 . . . 110
ZS = COM
REF
-REF
2
-FS =
1 LSB =
000 . . . 010
000 . . . 001
000 . . . 000
4096
100 . . . 010
100 . . . 001
100 . . . 000
REF
4096
1 LSB =
111 . . . 111
111 . . . 110
111 . . . 101
011 . . . 111
011 . . . 110
011 . . . 101
100 . . . 001
100 . . . 000
000 . . . 001
000 . . . 000
COM*
INPUT VOLTAGE (LSB)
- FS
+FS - 1 LSB
0
1
2
FS
2048
INPUT VOLTAGE (LSB)
(COM)
FS - 3/2 LSB
≤
*COM
V
/ 2
REF
Figure 8. Unipolar Transfer Function
Figure 9. Bipolar Transfer Function
Shutdown Mode
Transfer Function
Shutdown mode turns off all chip functions that draw qui-
escent current, reducing the typical supply current to
2µA immediately after the current conversion is complet-
ed. A rising edge on WR causes the MAX1265/MAX1267
to exit shutdown mode and return to normal operation.
To achieve full 12-bit accuracy with a 4.7µF reference
bypass capacitor, 50µs is required after power-up.
Waiting 50µs in standby mode, instead of in full-power
mode, can reduce power consumption by a factor of 3 or
more. When using an external reference, only 50µs is
required after power-up. Enter standby mode by per-
forming a dummy conversion with the control byte speci-
fying standby mode.
Table 5 shows the full-scale voltage ranges for unipolar
and bipolar modes. Figure 8 depicts the nominal unipo-
lar input/output (I/O) transfer function, and Figure 9
shows the bipolar I/O transfer function. Code transitions
occur halfway between successive-integer LSB values.
Output coding is binary, with 1 LSB = (V
/ 4096).
REF
Maximum Sampling Rate/
Achieving 300ksps
When running at the maximum clock frequency of
4.8MHz, the specified throughput of 265ksps is achieved
by completing a conversion every 18 clock cycles: 1
write cycle, 3 acquisition cycles, 13 conversion cycles,
and 1 read cycle. This assumes that the results of the
last conversion are read before the next control byte is
written. It is possible to achieve higher throughputs, up
to 300ksps, by first writing a control byte to begin the
Note: Bypass capacitors larger than 4.7µF between
REF and GND result in longer power-up delays.
______________________________________________________________________________________ 1.
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
CLK
WR
RD
D11–D0
CONTROL
WORD
D11–
D0
CONTROL WORD
CONVERSION
D7–D0
STATE
ACQUISITION
ACQUISITION
SAMPLING INSTANT
Figure 10. Timing Diagram for Fastest Conversion
the data bus during acquisition or conversion can
cause additional supply noise, which can make it diffi-
cult to achieve true 12-bit performance.
SUPPLIES
Layout, Grounding, and Bypassing
For best performance, use printed circuit (PC) boards.
Wire-wrap configurations are not recommended since
the layout should ensure proper separation of analog
and digital traces. Do not run analog and digital lines
parallel to each other, and do not lay out digital signal
paths underneath the ADC package. Use separate
analog and digital PC board ground sections with only
one star point (Figure 11) connecting the two ground
systems (analog and digital). For lowest noise opera-
tion, ensure the ground return to the star ground’s
power supply is low impedance and as short as possi-
ble. Route digital signals far away from sensitive analog
and reference inputs.
+3V
+3V
GND
4.7µF
0.1µF
*R = 5Ω
V
DD
GND
COM
+3V
DGND
DIGITAL
CIRCUITRY
MAX1265
MAX1267
*OPTIONAL
High-frequency noise in the power supply, V , could
DD
impair operation of the ADC’s fast comparator. Bypass
Figure 11. Power-Supply and Grounding Connections
V
to the star ground with a network of two parallel
DD
capacitors, 0.1µF and 4.7µF, located as close as to the
MAX1265/MAX1267s’ power-supply pin as possible.
Minimize capacitor lead length for best supply-noise
rejection and add an attenuation resistor (5Ω) if the
power supply is extremely noisy.
acquisition cycle of the next conversion, then reading the
results of the previous conversion from the bus. This
technique (Figure 10) allows a conversion to be com-
pleted every 16 clock cycles. Note that the switching of
16 ______________________________________________________________________________________
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
Signal-to-Noise Plus Distortion
Signal-to-noise plus distortion (SINAD) is the ratio of the
Definitions
Integral Nonlinearity
Integral nonlinearity (INL) is the deviation of the values
on an actual transfer function from a straight line. This
straight line can be either a best-straight-line fit or a line
drawn between the end points of the transfer function,
once offset and gain errors have been nullified. INL for
the MAX1265/MAX1267 is measured using the end-
point method.
fundamental input frequency’s RMS amplitude to the
RMS equivalent of all other ADC output signals:
SINAD (dB) = 20 x log (Signal
/ Noise
)
RMS
RMS
Effective Number of Bits
Effective number of bits (ENOB) indicates the global
accuracy of an ADC at a specific input frequency and
sampling rate. An ideal ADC error consists of quantiza-
tion noise only. With an input range equal to the full-
scale range of the ADC, calculate the effective number
of bits as follows:
Differential Nonlinearity
Differential nonlinearity (DNL) is the difference between
an actual step width and the ideal value of 1 LSB. A
DNL error specification of less than 1 LSB guarantees
no missing codes and a monotonic transfer function.
ENOB = (SINAD - 1.76) / 6.02
Total Harmonic Distortion
Total harmonic distortion (THD) is the ratio of the RMS
sum of the first five harmonics of the input signal to the
fundamental itself. This is expressed as:
Aperture Jitter
Aperture jitter (t ) is the sample-to-sample variation in
AJ
the time between the samples.
Aperture Delay
Aperture delay (t ) is the time between the rising
AD
edge of the sampling clock and the instant when an
actual sample is taken.
2
2
2
2
THD = 20 x log
V
+ V3 + V4 + V5 / V
(
)
2
1
Signal-to-Noise Ratio
For a waveform perfectly reconstructed from digital
samples, signal-to-noise ratio (SNR) is the ratio of the
full-scale analog input (RMS value) to the RMS quanti-
zation error (residual error). The ideal, theoretical mini-
mum analog-to-digital noise is caused by quantization
error only and results directly from the ADC’s resolution
(N bits):
where V1 is the fundamental amplitude, and V2 through
V5 are the amplitudes of the 2nd- through 5th-order
harmonics.
Spurious-Free Dynamic Range
Spurious-free dynamic range (SFDR) is the ratio of the
RMS amplitude of the fundamental (maximum signal
component) to the RMS value of the next-largest distor-
tion component.
SNR = (6.02 ✕ N + 1.76)dB
In reality, there are other noise sources besides quanti-
zation noise, including thermal noise, reference noise,
clock jitter, etc. Therefore, SNR is calculated by taking
the ratio of the RMS signal to the RMS noise, which
includes all spectral components minus the fundamen-
tal, the first five harmonics, and the DC offset.
Chip Information
TRANSISTOR COUNT: 5781
SUBSTRATE CONNECTED TO GND
______________________________________________________________________________________ 17
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
Typical Operating Circuits
CLK
CLK
+3V
+3V
MAX1267
V
MAX1265
V
DD
DD
+2.5V
+2.5V
CS
WR
RD
REF
CS
WR
RD
REF
µP
CONTROL
INPUTS
µP
CONTROL
INPUTS
0.1µF
0.1µF
REFADJ
REFADJ
INT
4.7µF
4.7µF
INT
OUTPUT STATUS
OUTPUT STATUS
D11
D10
D9
D11
D10
D9
D8
D8
D7
D6
D7
D6
CH5
CH4
D5
D4
D3
D5
D4
D3
CH3
CH2
CH1
ANALOG
INPUTS
CH1
D2
D2
ANALOG
INPUTS
CH0
CH0
D1
D0
D1
D0
COM
COM
GND
GND
µP DATA BUS
µP DATA BUS
Pin Configurations (continued)
TOP VIEW
D9
D8
D7
D6
D5
D4
D3
D2
D1
1
2
3
4
5
6
7
8
9
24 D10
23 D11
22
V
DD
21 REF
20 REFADJ
19 GND
18 COM
17 CH0
16 CH1
15 CS
MAX1267
D0 10
INT 11
RD 12
14 CLK
13 WR
QLOP
18 ______________________________________________________________________________________
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www0mꢁxim-ic0com/pꢁckꢁges.)
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________19
© 2003 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
相关型号:
MAX1265BCEI
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs with +2.5V Reference and Parallel Interface
MAXIM
MAX1265BCEI+T
ADC, Successive Approximation, 12-Bit, 1 Func, 6 Channel, Parallel, Word Access, PDSO28, 0.150 INCH, 0.025 INCH PITCH, MO-137, QSOP-28
MAXIM
MAX1265BCEI-T
ADC, Successive Approximation, 12-Bit, 1 Func, 6 Channel, Parallel, Word Access, PDSO28, 0.150 INCH, 0.025 INCH PITCH, MO-137, QSOP-28
MAXIM
MAX1265BEEI
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs with +2.5V Reference and Parallel Interface
MAXIM
MAX1265BEEI+T
ADC, Successive Approximation, 12-Bit, 1 Func, 6 Channel, Parallel, Word Access, PDSO28, 0.150 INCH, 0.025 INCH PITCH, MO-137, QSOP-28
MAXIM
MAX1265BEEI-T
ADC, Successive Approximation, 12-Bit, 1 Func, 6 Channel, Parallel, Word Access, PDSO28, 0.150 INCH, 0.025 INCH PITCH, MO-137, QSOP-28
MAXIM
MAX1265|MAX1267
265ksps. +3V. 6-/2-Channel. 12-Bit ADCs with +2.5V Reference and Parallel Interface
MAXIM
MAX1266ACEI
420ksps, +5V, 6-/2-Channel, 12-Bit ADCs with +2.5V Reference and Parallel Interface
MAXIM
MAX1266AEEI
420ksps, +5V, 6-/2-Channel, 12-Bit ADCs with +2.5V Reference and Parallel Interface
MAXIM
MAX1266AEEI+
ADC, Successive Approximation, 12-Bit, 1 Func, 6 Channel, Parallel, Word Access, PDSO28, 0.150 INCH, 0.025 INCH PITCH, MO-137, QSOP-28
MAXIM
MAX1266AEEI+T
ADC, Successive Approximation, 12-Bit, 1 Func, 6 Channel, Parallel, Word Access, PDSO28, 0.150 INCH, 0.025 INCH PITCH, MO-137, QSOP-28
MAXIM
©2020 ICPDF网 联系我们和版权申明