MAX11500EVKIT [MAXIM]
Surface-Mount Components;型号: | MAX11500EVKIT |
厂家: | MAXIM INTEGRATED PRODUCTS |
描述: | Surface-Mount Components |
文件: | 总6页 (文件大小:130K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
19-0954; Rev 0; 8/07
MAX11500 Evaluation Kit
Evluates:MAX150
General Description
Features
The MAX11500 evaluation kit (EV kit) is a fully assem-
bled and tested surface-mount printed-circuit board
(PCB) that contains a MAX11500 IC. The MAX11500 is
a 3-channel HD video filter for reconstruction and anti-
aliasing applications. The filter’s -3dB frequency is
33MHz. The MAX11500 includes a +6dB output buffer
♦ Single 5V Supply Operation
♦ Output Buffer Drives a 150Ω Standard Video Load
with a +6dB Gain
♦ High-Definition Video Filter
♦ AC- or DC-Coupled Inputs/Outputs
♦ Standard 75Ω Input/Output Terminations
♦ Surface-Mount Components
capable of driving a 2V
video signal into a standard
P-P
150Ω load.
The MAX11500 EV kit can be configured for both AC-
and DC-coupled inputs and outputs. The MAX11500
video inputs have 75Ω termination to ground and the
outputs are 75Ω back terminated. The EV kit operates
from a single 5V power supply.
♦ Fully Assembled and Tested
Ordering Information
PART
TEMP RANGE
IC PACKAGE
MAX11500EVKIT+
0°C to +70°C*
8 SO
+Denotes a lead-free and RoHS-compliant EV kit.
*This limited temperature range applies to the EV kit PCB only.
The MAX11500 IC temperature range is 0°C to +85°C.
Component List
DESIGNATION
U1
QTY
DESCRIPTION
MAX11500USA+ (8-pin SO)
PC mini-black test points
DESIGNATION
QTY
DESCRIPTION
1
2
0.1µF 10ꢀ, 25V X7R ceramic
capacitors (0603)
C1, C2, C3, C5
4
GND, GND
Murata GRM188R71E104K
IN1, IN2, IN3,
OUT1, OUT2,
OUT3
1µF 10ꢀ, 25V X7R ceramic
capacitor (0805)
Murata GRM21BR71E105K
6
PC mini-red test points
C4
1
3
VIDIN1, VIDIN2,
VIDIN3,
220µF 20ꢀ, 6.3V aluminum
electrolytic capacitors
(8.3mm x 8.3mm)
75Ω BNC PCB-mount jack
VIDOUT1,
VIDOUT2,
VIDOUT3
6
C6, C7, C8
connectors
SANYO 6SVPA220MAA
JU1–JU9
R1, R4, R7
9
3
3
6
2-pin headers
—
—
9
1
Shunts (JU1–JU9)
820k
120k
Ω
Ω
5ꢀ resistors (0603)
5ꢀ resistors (0603)
PCB: MAX11500 Evaluation Kit+
R2, R5, R8
R3, R6, R9–R12
75Ω 1ꢀ resistors (0603)
Component Suppliers
SUPPLIER
PHONE
WEBSITE
Murata Mfg. Co.,
Ltd.
770-436-1300 www.murata.com
SANYO North
America Corp.
619-661-6835 www.sanyodevice.com
Note: Indicate that you are using the MAX11500 when contact-
ing these component suppliers.
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX11500 Evaluation Kit
The video inputs and outputs can also be configured
for DC-coupled operation. The MAX11500 EV kit video
inputs have a 75Ω termination to ground and the out-
puts are 75Ω back terminated.
Quick Start
Recommended Equipment
Before beginning, the following equipment is needed:
• 5V, 200mA DC power supply (V
)
CC
Jumper Selection
• Video signal generator (e.g., Tektronix TG-2000 or
TG-700)
AC-/DC-Coupled Input Operation
The MAX11500 features a transparent clamp at the video
inputs that allows for either AC- or DC-coupling. If the
input signal remains above ground, the transparent
clamp is inactive, offering true DC-input coupling. If the
signal goes below ground, it must be AC-coupled. The
transparent clamp will set the sync tip just below ground.
• Video measurement equipment (e.g., Tektronix
VM-6000 or equivalent)
Procedure
The MAX11500 EV kit is fully assembled and tested.
Follow the steps below to verify board operation.
Caution: Do not turn on the power supply until all
connections are completed.
Jumpers JU1, JU3, and JU5 set the MAX11500 EV kit
video inputs for AC- or DC-coupled operation. For AC-
coupled operation, remove shunts from jumpers JU1,
JU3, and JU5. For DC-coupled operation, install shunts
across jumpers JU1, JU3, or JU5. Use DC-coupling
only for input signals whose lowest voltage is above
ground. See Table 1 for proper jumper settings. When
interfacing DC-coupled signals to the MAX11500 EV kit
VIDIN_ inputs, verify that shunts are not installed across
jumpers JU2, JU4, or JU6.
1) Connect the video signal generator output to the
VIDIN_ BNC connectors on the MAX11500 EV kit.
2) Connect the VIDOUT_ BNC connectors on the EV kit
to the input of the video measurement equipment.
3) Connect the power-supply ground to the GND pad
on the EV kit.
Evluates:MAX150
4) Connect the 5V supply to the VCC pad on the EV kit.
5) Verify that no shunts are installed across jumpers
JU1, JU3, JU5, JU7, JU8, and JU9 (AC-coupled
inputs and outputs), and JU2 (no DC bias at VIDIN1).
Table 1. AC-/DC-Coupled Input Operation
(JU1, JU3, and JU5)
SHUNT POSITION
Not installed
Installed
EV KIT INPUTS
6) Install shunts across jumpers JU4 and JU6 (DC
bias for VIDIN2 and VIDIN3).
AC-coupled operation
DC-coupled operation
7) Set the video signal generator for the desired video
input signal using a YP P signal format.
B R
DC Bias for YP P Signals
B R
8) Connect the Y signal to the VIDIN1 BNC connector,
When configuring the EV kit video inputs for AC-
coupled operation, the correct DC bias point has to be
chosen, depending on the input signal. Unipolar signals,
such as R, G, B, and Y, are biased correctly using the
MAX11500 internal transparent clamp. For bipolar sig-
and P and P to VIDIN2 and VIDIN3, respectively.
B
R
9) Turn on the power supply and enable the video signal
generator output.
10) Analyze the video output signal with the video mea-
surement equipment.
nals, such as P and P signals, a constant DC bias volt-
B
R
age has to be applied after the AC-coupling capacitor to
make sure that the clamp never operates. A 590mV DC
bias voltage can be applied by installing shunts across
jumpers JU2, JU4, or JU6. To configure the inputs to a
different DC bias voltage, replace resistors R2, R5, or R8.
See Table 2 for input clamp configuration.
Detailed Description
The MAX11500 EV kit is a fully assembled and tested
surface-mount PCB that contains a MAX11500 IC. The
MAX11500 is a 3-channel video filter for reconstruction
and anti-aliasing applications. All 3 channels have iden-
tical characteristics.
Table 2. Input Clamp Operation (JU2,
JU4, and JU6)
The MAX11500 filter’s -3dB frequency is 33MHz. The
device includes a +6dB output buffer capable of dri-
video signal into a standard 150Ω load. In
the default configuration, the MAX11500 EV kit video
inputs and outputs are set for AC-coupled operation.
ving a 2V
P-P
SHUNT
EV KIT FUNCTION
POSITION
Installed
DC bias enabled: Use for P , P signals
B R
Not installed
DC bias disabled: Use for R, G, B, Y signals
2
_______________________________________________________________________________________
MAX11500 Evaluation Kit
Evluates:MAX150
AC-/DC-Coupled Output Operation
Jumpers JU7, JU8, and JU9 configure the MAX11500
EV kit video outputs for AC- or DC-coupled operation.
To configure the outputs for AC-coupled operation,
remove shunts from jumpers JU7, JU8, and JU9. To
configure the outputs for DC-coupled operation, install
shunts across jumpers JU7, JU8, and JU9. See Table 3
for the EV kit output configuration.
Table 3. AC-/DC-Coupled Output Operation
(JU7, JU8, and JU9)
SHUNT POSITION
Not installed
Installed
EV KIT OUTPUTS
AC-coupled operation
DC-coupled operation
VCC
VCC
GND
C4
1μF
JU7
VCC
R10
75Ω
1%
C6
220μF
OUT1
4
5
8
R1
820kΩ
V
OUT1
VIDOUT1
CC
R2
120kΩ
C5
0.1μF
JU1
GND
IN1
C1
0.1μF
IN1
JU2
1
2
3
VIDIN1
VIDIN2
VIDIN3
VCC
U1
R3
75Ω
1%
MAX11500
R4
820kΩ
R5
120kΩ
JU3
JU8
R11
75Ω
1%
C2
0.1μF
C7
220μF
IN2
OUT2
GND
JU4
7
IN2
OUT2
VIDOUT2
VCC GND
R6
75Ω
1%
R7
820kΩ
R8
120kΩ
JU5
JU9
R12
75Ω
1%
C3
0.1μF
C8
220μF
IN3
OUT3
JU6
6
IN3
OUT3
VIDOUT3
R9
75Ω
1%
Figure 1. MAX11500 EV Kit Schematic
_______________________________________________________________________________________
3
MAX11500 Evaluation Kit
Evluates:MAX150
Figure 2. MAX11500 EV Kit Component Placement Guide—Component Side
4
_______________________________________________________________________________________
MAX11500 Evaluation Kit
Evluates:MAX150
Figure 3. MAX11500 EV Kit PCB Layout—Component Side
_______________________________________________________________________________________
5
MAX11500 Evaluation Kit
Evluates:MAX150
Figure 4. MAX11500 EV Kit PCB Layout—Solder Side
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
6 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2007 Maxim Integrated Products
is a registered trademark of Maxim Integrated Products, Inc.
CARDENAS
相关型号:
©2020 ICPDF网 联系我们和版权申明