258-997-64 [MARL]
FILAMENT REPLACEMENT LEDs - T6.8SB; 更换灯丝发光二极管 - T6.8SB型号: | 258-997-64 |
厂家: | MARL INTERNATIONAL LIMITED |
描述: | FILAMENT REPLACEMENT LEDs - T6.8SB |
文件: | 总3页 (文件大小:251K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
FEATURES
FILAMENT REPLACEMENT LEDs - T6.8SB
l
l
Direct replacement for T6.8 Slide Base
258 SERIES
PACK QUANTITY = 10 PIECES
Unique SOLO Technology - single product for multi-
voltage operating range
l
Flat-topped for enhanced, even illumination of large
lens areas
l
l
Durable to shock and vibration
Reduces stock and maintenance costs
SPECIFICATIONS
Ordering Information & Typical Technical Characteristics (Ta = 25°C)
Mean Time Between Failure = 100,000 Hours. Luminous intensity figures refer to the unmodified discrete LED.
PART NUMBER
COLOUR
LENS
VOLTAGE
DC
CURRENT
DC
LUMINOUS
INTENSITY
lv@20mA
WAVE
LENGTH
λp
OPERATING
TEMP
STORAGE
TEMP
Vopr
lopr
Topr
Tstg
HIGH INTENSITY
258-501-64
258-501-64-38
258-521-64
258-521-64-38
258-532-64
258-532-64-38
258-930-64
258-930-64-38
258-997-64
258-997-64-38
258-993-64
258-993-64-38
UNITS
Red
Water Clear
Water Clear
Water Clear
Water Clear
Water Clear
Water Clear
Water Clear
Water Clear
Water Clear
Water Clear
Water Clear
Water Clear
8-48
8-48
8-48
8-48
8-48
8-48
8-48
8-48
8-48
8-48
8-48
8-48
Vdc
10
10
10
10
10
10
10
10
10
10
10
10
mA
11000
11000
16000
16000
23000
23000
7000
624
-40 ~ +95^
-40 ~ +95^
-40 ~ +95^
-40 ~ +95^
-40 ~ +95^
-40 ~ +95^
-40 ~ +95^
-40 ~ +95^
-40 ~ +95^
-40 ~ +95^
-30 ~ +85^
-30 ~ +85^
0C
-40 ~ +100
-40 ~ +100
-40 ~ +100
-40 ~ +100
-40 ~ +100
-40 ~ +100
-40 ~ +100
-40 ~ +100
-40 ~ +100
-40 ~ +100
-40 ~ +100
-40 ~ +100
0C
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Red
624
Yellow
591
Yellow
591
Green
527
Green
527
Blue
470
Blue
7000
470
Cool White
Cool White
Warm White
Warm White
14000
14000
9200
*see below
*see below
**see below
**see below
nm
9200
mcd
258 series ending in -64 denotes Narrow viewing angle.
258 series ending in -64-38 denotes Wide viewing angle.
997F-C *Typical emission colour cool white
x
0.245
0.361
0.356
0.264
y
0.229
0.385
0.351
0.220
Please note this product will illuminate below 8Vac/dc but will not stabilise at
10mA until the 8 volt threshold has been reached.
993
x
**Typical emission colour warm white
0.426
Absolute maximum input voltage is 50Vac/dc.
0.439
0.497
0.477
^ = Products must be derated according to the derating information. Each derating graph refers to
specific LEDs. Appropriate LED numbers shown. - Refer to page 3.
y
0.400
0.431
0.446
0.413
Intensities (lv) and colour shades of white (x,y co-ordinates) may vary between LEDs within a batch.
How to Order:
website: www.marl.co.uk
email: sales@marl.co.uk
Fax: +44 (0)1229 585155
•
•
Telephone +44 (0)1229 582430
•
•
The information contained in this datasheet does not constitute part of any order or contract and should not be regarded as a representation
relating to either products or service. Marl International reserve the right to alter without notice the specification or any conditions of supply
for products or service.
Page 1 of
3
© MARL INTERNATIONAL LTD 2006 : DS 096/06 Issue 1
SAMPLES AVAILABLE
258 Series
Colour dot on product denotes LED colour
Dimensions in mm (Typical)
Not to scale
TECHNICAL INFORMATION
Lamp Base Style
Series
258
Metric Equivalent (mm)
Maximum Power Dissipation (mW)
625
Telephone Slide Base T6.8
-
DESIGN CONSIDERATIONS
Single-Chip LEDs
All devices feature water clear high intensity LEDs as standard. The single chip LED devices have been modified by the removal of the domed
portion of the encapsulation (flat-topped) to provide even illumination of switches and annunciators. Non flat topped versions are also available,
please contact the sales department for details.
Product Evaluation
Filament Replacement LEDs have been specifically designed to meet the primary objective of providing improved reliability. As this product range
is suitable for both new-build and retro-fit, (sometimes in very old systems), a wide range of illuminated push button switches and lamp holders
can be encountered. Due to subjectivity, evaluation of the LED type is recommended, (samples of all standard models are available). care should
be taken to correctly simulate operating ambient light conditions to ensure that the correct device has been selected to maximise viewing
characteristics such as viewing angle, colour compatibility and on/off contrast ratio.
Electro-static Discharge (ESD)
Build up of electrostatic discharge occurs in many situations involving people moving and handling products. The range of possible situations is
very diverse but voltage levels as high as several thousand volts can and do arise in many individual situations. When an operator charged up to
these levels handles a ‘static sensitive device’, there is a very probable likelihood that the device will be irreversibly damaged. It is essential that
precautions are taken at all stages during manufacture and assembly of these products. Although LEDs were never considered to be static
sensitive devices, changes in manufacturing technology and materials used to produce higher intensity products over a large range of the
wavelength spectrum have changed this. Marl has an approved system of ESD control from goods in, through production and into final packing
and despatch. We recommend all users of LED based products follow the guidelines of BS 100015.
Power derating
The forward voltage/current value of an LED is dependant upon the ambient temperature of the environment in which it is operated. Therefore,
care must be taken to operate the LED at the correct voltage/current values, depending upon the ambient temperature. Consequently, a
recommendation regarding operating voltages and currents is given in order to address these temperature effects. This recommendation is
termed ‘de-rating’.
It is usual for forward voltages and currents to be specified for ambient temperature of 25°C. However, because the values of these qualities vary
with temperature, Marl should be contacted if the device is to be operated at a temperature significantly higher than 25°C.
Marl accept no liability for any product that is operated higher than the stated voltage.
Note:
All luminous intensity figures refer to the unmodified discrete LED.
How to Order:
website: www.marl.co.uk
email: sales@marl.co.uk
Fax: +44 (0)1229 585155
•
•
Telephone +44 (0)1229 582430
•
•
The information contained in this datasheet does not constitute part of any order or contract and should not be regarded as
a
representation
BS EN ISO 9001:2000
Approved Manufacturer
relating to either products or service. Marl International reserve the right to alter without notice the specification or any conditions of supply
for products or service.
©
MARL INTERNATIONAL LTD 2006
:
DS 096/06 Issue
1
SAMPLES AVAILABLE
Page
2
of
3
DERATING INFORMATION
993
501
&
521
532, 930
&
997
How to Order:
website: www.marl.co.uk
email: sales@marl.co.uk
Fax: +44 (0)1229 585155
•
•
Telephone +44 (0)1229 582430
•
•
The information contained in this datasheet does not constitute part of any order or contract and should not be regarded as
a
representation
BS EN ISO 9001:2000
Approved Manufacturer
relating to either products or service. Marl International reserve the right to alter without notice the specification or any conditions of supply
for products or service.
©
MARL INTERNATIONAL LTD 2006
:
DS 096/06 Issue
1
SAMPLES AVAILABLE
Page
3
of
3
相关型号:
258.1%FA3/420PPM-AMMOPACK
Fixed Resistor, Wire Wound, 0.75W, 258ohm, 32V, 0.1% +/-Tol, -20,20ppm/Cel,
VISHAY
258.25%FA3/420PPM-AMMOPACK
Fixed Resistor, Wire Wound, 0.75W, 258ohm, 32V, 0.25% +/-Tol, -20,20ppm/Cel,
VISHAY
258.25%FA3/420PPM-CARDPACK
Fixed Resistor, Wire Wound, 0.75W, 258ohm, 32V, 0.25% +/-Tol, -20,20ppm/Cel,
VISHAY
258.25%FA4B20PPM-CARDPACK
Fixed Resistor, Wire Wound, 4W, 258ohm, 210V, 0.25% +/-Tol, -20,20ppm/Cel,
VISHAY
258.25%FA7A20PPM-TANDR
Fixed Resistor, Wire Wound, 7W, 258ohm, 490V, 0.25% +/-Tol, -20,20ppm/Cel,
VISHAY
258.5%FA3/420PPM-CARDPACK
Fixed Resistor, Wire Wound, 0.75W, 258ohm, 32V, 0.5% +/-Tol, -20,20ppm/Cel,
VISHAY
©2020 ICPDF网 联系我们和版权申明