V23201-R1005-A502 [MACOM]
Power Relay PK2 (THT â THR) Single Relays PCB Relays; 功率继电器PK2 （ THT â ???? THR ）单PCB继电器继电器
| 型号： | V23201-R1005-A502 |
| 厂家： | 
Tyco Electronics |
| 描述： | Power Relay PK2 (THT â THR) Single Relays PCB Relays |
| 文件： | 总5页 (文件大小：420K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
PCB Relays
Single Relays
Catalog 1308028-2
Revised 3-2008
Power Relay PK2 (THT – THR)
Features
– 60% volume reduced
Power K at increased
performance
– PCB area requirements
minimized by 50% to
only 293 mm2
– Size optimized to
L x W x H (mm)
18.3 x 16 x 15.9
– Limiting continuous
current 40 A
– Maximum switch on
current 200 A
– Increased ambient
temperature 105°C
– Design allows highest
reliability
– High shock and vibration
resistance
– Wave (THT) and reflow
(THR/pin-in-paste)
solderable versions
– For latching (bistable)
version refer to
Power Relay PK2 Latching
Typical Applications
– ABS control
– Blower fans
– Cooling fan
– Engine control
– Fuel pump
201_C-R_3D3
– Glow plug
Design
– ELV/RoHS/WEEE compliant
– THT: sealed type washable
– THR: sealed type open vent hole
Terminals
PCB terminals for assembly on
printed circuit boards
Conditions
– Hazard warning signal
– Switched power supply
All parametric, environmental and
endurance tests are performed
according to EIA Standard RS-407-A
at standard test conditions unless
otherwise noted:
Please contact Tyco Electronics for
relay application support.
Weight
Approx. 11 g (0.39 oz.)
23°C ambient temperature,
20 - 50% RH, 998.9 33.9 hPa.
Nominal Voltage
12 V
For general storage and processing
recommendations please refer to our
Application Notes and especially to
Storage in the “Glossary” page 23 or
at http://relays.tycoelectronics.com/
appnotes/
Disclaimer
All technical performance data apply to the relay as such, specific conditions of the individual application are not considered. Please always check the suitability of the
relay for your intended purpose. We do not assume any responsibility or liability for not complying herewith. We recommend to complete our questionnaire and to request
our technical service. Any responsibility for the application of the product remains with the customer only. All specifications are subject to change without notification.
All rights of Tyco Electronics are reserved.
134
All specifications subject to change. Consult Tyco Electronics for latest specifications.
PCB Relays
Single Relays
Catalog 1308028-2
Revised 3-2008
Power Relay PK2 (THT – THR)
Dimensional Drawing
*) Additional tin tops max. 1 mm
201C_DD2
201C_DD1
View of the Terminals (bottom view)
Remark: Positional tolerances according to DIN EN ISO 5458
**) without tinning (hop dip)
201C_VT1
All specifications subject to change. Consult Tyco Electronics for latest specifications.
135
PCB Relays
Single Relays
Catalog 1308028-2
Revised 3-2008
Power Relay PK2 (THT – THR)
Contact Data
Typical areas of application
Contact configuration
Resistive/inductive/capacitive load
1 Make contact/
1 Form A
5 (+)
4 (-)
Circuit Symbol
(see also Pin assignment)
Rated voltage
Rated current 1)
at
12 V
33 A
Limiting continuous current 1)
23°C
85°C
40 A
33 A
105°C
22 A
Contact material
Silver based
See load limit curve
Max. switching voltage/power
Max. switching current 2)
On
200 A
40 A
Off
Min. recommended load3)
Voltage drop at 10 A (initial)
NO contact
Mechanical endurance (without load)
Examples of electrical endurance
at cyclic temperature –40/+23/+85°C
1 A at 5 V
Typ. 30 mV, 300 mV max.
> 2 x 106 operations
Inductive load: > 1 x 105 operations, 60 A on/35 A 0ff, L = 0.5 mH
Resistive load: > 1 x 105 operations, 40 A on/40 A 0ff
Capacitive load: > 1 x 105 operations, 200 A on/20 A 0ff
6 operations per minute (0.1 Hz)
and 13.5 V; 120 ms - on/4880 ms - off
Max. switching rate at nominal load
1)
Measured on 70 mm x 70 mm x 1.5 mm epoxy PCB FR4 with 52 cm2 (double layer 140 μm thick) copper area.
The values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5 V for 12 V load voltages.
See chapter Diagnostics of Relays in our Application Notes page 31 or consult the internet at http://relays.tycoelectronics.com/appnotes/
2)
3)
Load Limit Curve
201C_LLC3
^
Load limit curve = safe shutdown, no stationary
arc/make contact
136
All specifications subject to change. Consult Tyco Electronics for latest specifications.
PCB Relays
Single Relays
Catalog 1308028-2
Revised 3-2008
Power Relay PK2 (THT – THR)
Circuit Diagram
1 Make contact/1 Form A
5(+)
4(-)
1(-)
2(+)
201C_PA2
Coil Data
Available for nominal voltages
12 V
0.8 W
Nominal power consumption of the unsuppressed coil at nominal voltage (monostable)
Test voltage winding/contact
Maximum ambient temperature range 1)
500 VACrms
–40 to +105°C
Typ. 3 ms
Typ. 1.5 ms
Operate time at nominal voltage
Release time at nominal voltage 2)
1)
See also operating voltage range diagram.
For unsuppressed relay coil.
2)
Note:
A low resistive suppression device in parallel to the relay coil increases the release time and reduces
the lifetime caused by increased erosion and/or higher risk of contact tack welding (monostable version only).
Operating Voltage Range
201C_OVR1
Does not take into account
the temperature rise due to
the contact current
E = pre-energization
All specifications subject to change. Consult Tyco Electronics for latest specifications.
137
PCB Relays
Single Relays
Catalog 1308028-2
Revised 3-2008
Power Relay PK2 (THT – THR)
Environmental Conditions
Temperature range, storage
Test
Refer to Storage in the “Glossary” catalog page 23 or http://relays.tycoelectronics.com/appnotes/
Relevant standard
IEC 68-2-1
Testing as per
Dimension
1000 h
Comments
–40°C
Cold storage
Dry heat
Thermal shock 1)
IEC 68-2-2
IEC 68-2-14
Ba
Na
1000 h
1000 cycles
125°C
–40/+125°C
Dwell time 15 min
Vibration resistance
Shock resistance
Solderability
IEC 68-2-6 (sine pulse form)
IEC 68-2-27 (half sine form single pulses)
30 - 440 Hz
> 20 g
6 ms >30 g
11 ms > 100 g
Hot dip 5 s
215°C
245°C
Hot dip 10 s
260°C
No change in the
switching state > 10 μs
Open contact will not close > 10 μs
Closed contact will not open > 10 μs
Aging 3 (4 h/155°C)
for leaded process (Tm = 183°C)
for Pb-free process (Tm = 217°C)
with thermal screen
THT
THR
IEC 68-2-20
IEC 68-2-58
Ta, Method 1
Tb, Method 1A
Qc, Method 2
Resistance to soldering heat
Sealing
THT
THR
IEC 68-2-20
IEC 68-2-58
260°C
Preheating min 130°C
THT
THR
IEC 68-2-17
1 min/70°C
Open vent hole
1)
Only storage.
Ordering Information
Part Numbers
(see table below for coil data)
Contact
Arrangement
Contact
Material
Enclosure
Soldering
Technology
Relay Description
Part Number
V23201-C1001-A502
V23201-R1005-A502
5-1414782-7
6-1414932-3
Form A
Form A
Silver based
Silver based
Sealed
THT
THR
Open vent hole
Coil Versions
1)
Coil Data
for
PK2
Rated Coil
Voltage
(V)
Coil Resistance
Must
Operate Voltage
(V)
Must
Release Voltage
(V)
Allowable Overdrive
Voltage (V)
at 23°C
1ꢀ0
(Ω)
– THT/THR
at 1ꢀ5°C
V23201-***01-****
V23201-***05-****
12
12
176
176
6.9 2)
6.9 2)
1.5
1.5
27
17
17
27
1)
Allowable overdrive is stated with no load applied and minimum coil resistance.
Standard Delivery Packs (orders in multiples of delivery pack)
PK2 – THT/THR:
600 pieces
138
All specifications subject to change. Consult Tyco Electronics for latest specifications.
相关型号：
©2020 ICPDF网 联系我们和版权申明