7-22468-0 [MACOM]
Read the following instructions carefully before and during the installation of the conversion kits on the machine.;
| 型号： | 7-22468-0 |
| 厂家： | 
Tyco Electronics |
| 描述： | Read the following instructions carefully before and during the installation of the conversion kits on the machine. |
| 文件： | 总4页 (文件大小：205K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
ITEM NO.
PART NO.
690671–1
690672–2
4–21002–4
3–21000–6
690673–2
2–21000–7
690674–1
21009–4
DESCRIPTION
QTY
1
1
2
PLATE, Base
MOUNT, Base
1
3
SCREW, Btn Hd Cap, 3/8–16 x .500 in. L
SCREW, Skt Hd Cap, No. 10–32 x .625 in. L
BRACKET, Hold–Down
SCREW, Skt Hd Cap, No. 8–32 x .500 in. L
STOP, Rear
3
4
2
5
1
6
2
7
2
8
SETSCREW, Skt, Slflkg, 1/4–20 x .375 in. L
RAM
1
9
690499–1
––
1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Deleted
––
REF
1
694925–1*
694928–2
470268–1
3–21000–1
27708–3
BRACKET ASSY, Vertical Reel
BRACKET, LH Stock Guide
GUIDE, Stock
1
SCREW, Skt Hd Cap, No. 8–32 x 1.00 in. L
KNOB, Thumbscrew
4
2
21022–2
NUT, Slflkg, No. 8–32
1
455744–1
455745–1
1–21899–3
21018–6
SHROUD, End Feed
1
GUARD, End Feed
1
WASHER, Flat, No. 8
12
7
NUT, Hex, No. 8–32
7–22468–0
7–22468–3
22280–1
SCREW, Bdg Hd, No. 8–32 x .375 in. L
SCREW, Bdg Hd, No. 8–32 x .750 in. L
SPRING, Compression
5
1
1
455748–1
455749–1
3–21002–4
21899–3
SHROUD, Side Feed
1
GUARD, Side Feed
1
SCREW, Btn Hd Cap, 1/4–20 x .625 in. L
WASHER, Flat, 1/4 in.
1
1
*Refer to Customer Manual 409–5128 for the detailed parts breakdown of assembly and related parts..
Figure 1
3. Remove the two base mount screws and
washers form frame and install the base mount
supplied in the kit. Adjust height of the base mount
as low as possible in accordance with the machine
manual.
These conversion kits are used to modify
AMP–O–LECTRIC Model K Terminating Machines to
accept miniature quick–change applicators. Kit No.
690675–2 is required for all end–feed and those
side–feed applicators that receive the strip terminals
in a horizontal position. Refer to the exploded view
and parts list in Figure 1 to make sure you have all
the parts required for the conversion. Kit No.
690675–2 plus Kit No. 692613–1 are required for
those side–feed applicators that receive the strip
terminals in a vertical position.
4. Hand–cycle in accordance with the machine
manual until the toggle link is at its lowest position.
5. Remove the arm retaining plate by removing the
four screws.
6. Loosen the setscrew in the ram, and then pivot
the toggle link toward the front of the machine and
slide out the toggle link pin to remove the ram.
7. Lubricate the four sides of the new ram,
supplied in the kit, as specified in the machine
manual.
Read the following instructions carefully before and
during the installation of the conversion kits on the
machine.
8. Pivot the toggle link forward and install the new
ram with the toggle link pin removed in Step 6.
Pivot the ram back into position and tighten the
setscrew provided in the kit.
9. Install the ram retaining plate with the four
screws removed in Step 6.
Before starting installation of the conversion kits,
remove and store mechanical feed arm or air feed
operation arm from feed mechanism shaft by
loosening or removing clamp screws.
10. Hand–cycle the machine to the rest position
(top dead center).
11. All parts removed for conversion, and any
unused parts of the kit, should be retained and
stored.
This kit, in addition to Kit 690675–2, is required ONLY
for side feed applicators that receive strip terminals in
a vertical position.
1. Lay out the machine frame for holes as shown
in Figure 3.
2. Drill two size “G” holes, and thread with 5/16–18
UNC–2B tap.
For installation of this kit, the machine must be
equipped with the proper vertical reel bracket
assembly (Part No. 694925–1). For information
pertaining to this assembly, refer to Customer Manual
409–5128.
3. Assemble the reel support as shown and install
on the machine with the two screws supplied in the
kit.
1. The left–hand stock guide is required ONLY
when using side–feed applicators. With guide
installed on the bracket, attach the bracket to the
vertical reel bracket assembly with two screws
capped with knurled knobs, as shown.
it is NECESSARY for all miniature quick–change
applicators, when used in an AMP–O–LECTRIC
machine, to be equipped with the CORRECT feed
cam as listed on the applicator parts list (log) supplied
with the applicator. CHECK the feed cam, and if
necessary, replace it as described in the applicator
instructions supplied with the applicator. Retain all
parts that are removed.
2. To guide the terminal strip properly into
end–feed applicators, it is necessary that the
right–hand stock guide bracket be lowered by
using the UPPER hold in the vertical support for
the left screw, as shown.
SEE FIGURE 3 FOR DRILLING OF FRAME AND
INSTALLATION OF REEL BRACKET ASSEMBLY
FOR KIT NO. 692613–1.
(REFER TO 409–5128)
Figure 2
Figure 3
5. Set the wire disc and insulation disc for the wire
gage to be used in accordance with the data plate
on the applicator and/or the applicator parts list
supplied with the applicator.
6. Adjust the base mount for the correct crimp
height in accordance with the machine manual.
7. Install the side feed or end feed shroud and
guard assembly, for the type of applicator installed,
as shown in Figure 2.
1. Install the movable stop on the back of the base
mount for the end feed applicator or on the left end
for the side feed applicator, as shown in Figure 2.
8. To remove the applicator from the machine,
unload the applicator tooling according to the
instruction sheet shipped with the applicator,
remove the hold–down bracket, and slide the
applicator away from the stops on the base mount
until the ram post is clear of the machine ram.
2. Place the applicator on the base mount, insert
the ram post in the machine ram, then slide the
applicator into position against the stops.
3. Secure the applicator with the hold–down
bracket and two screws supplied in the kit. The
location of the hold–down bracket differs for end
feed and side feed applicators. Make certain the
bracket is located correctly.
Revisions to this instruction sheet include:
4. Load the applicator in accordance with the
applicator instruction sheet supplied with the
applicator.
Updated document to current requirements
New format
相关型号：
7-22468-3
Read the following instructions carefully before and during the installation of the conversion kits on the machine.
MACOM
©2020 ICPDF网 联系我们和版权申明