LTC1337CN [Linear]

5V Low Power RS232 3-Driver/5-Receiver Transceiver; 5V低功耗RS232 3驱动器/ 5接收器收发器
LTC1337CN
型号: LTC1337CN
厂家: Linear    Linear
描述:

5V Low Power RS232 3-Driver/5-Receiver Transceiver
5V低功耗RS232 3驱动器/ 5接收器收发器

线路驱动器或接收器 驱动程序和接口 接口集成电路 光电二极管
文件: 总8页 (文件大小:235K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
LTC1337  
5V Low Power RS232  
3-Driver/5-Receiver Transceiver  
U
DESCRIPTIO  
EATURE  
Low Supply Current: 300µA  
1µA Supply Current in SHUTDOWN  
ESD Protection: Over ±10kV  
Operates from a Single 5V Supply  
Uses Small Capacitors: 0.1µF  
Operates to 120k Baud  
Three-State Outputs Are High Impedance When Off  
Output Overvoltage Does Not Force Current Back into  
Supplies  
RS232 I/O Lines Can Be Forced to ±25V without  
Damage  
Pin Compatible with LT1137A and LT1237  
Flowthrough Architecture  
S
F
The LTC1337 is a 3-driver/5-receiver RS232 transceiver  
with very low supply current. In the no load condition, the  
supply current is only 300µA. The charge pump only  
requires four 0.1µF capacitors and can supply up to 12mA  
of extra current to power external circuitry.  
In SHUTDOWN mode, the supply current is further re-  
duced to 1µA. All RS232 outputs assume a high imped-  
ance state in SHUTDOWN and with the power off.  
The LTC1337 is fully compliant with all data rate and  
overvoltage RS232 specifications. The transceiver can  
operate up to 120k baud with a 1000pF//3kload. Both  
driver outputs and receiver inputs can be forced to ±25V  
without damage, and can survive multiple ±10kV ESD  
strikes.  
O U  
PPLICATI  
Notebook Computers  
Palmtop Computers  
S
A
U
O
TYPICAL APPLICATI  
3-Drivers/5-Receivers with SHUTDOWN  
Supply Current  
1.2  
1.0  
0.8  
0.6  
0.4  
0.2  
0
600  
500  
400  
300  
200  
100  
0
+
V
1
2
28  
27  
26  
25  
24  
23  
22  
21  
20  
19  
18  
17  
16  
15  
V
V
LTC1337  
C1  
0.1µF  
C4  
0.1µF  
CC  
C3  
0.1µF  
3
C2  
0.1µF  
4
DRIVER 1 IN  
RX1 OUT  
DRIVER 2 IN  
RX2 OUT  
RX3 OUT  
RX4 OUT  
DRIVER 3 IN  
RX5 OUT  
GND  
QUIESCENT  
CURRENT  
5
DRIVER 1 OUT  
RX1 IN  
6
7
DRIVER 2 OUT  
RX2 IN  
8
SHUTDOWN  
CURRENT  
9
RX3 IN  
10  
11  
12  
13  
14  
RX4 IN  
DRIVER 3 OUT  
RX5 IN  
0
20  
40  
60  
80  
–20  
TEMPERATURE (°C)  
ON/OFF  
TEST CONDITION:  
= 5V, ALL DRIVER INPUTS TIED TO V  
V
CC  
CC  
1337 TA01  
1337 TA02  
1
LTC1337  
W W W  
U
/O  
ABSOLUTE AXI U RATI GS  
PACKAGE RDER I FOR ATIO  
(Note 1)  
ORDER PART  
Supply Voltage (VCC) ................................................ 6V  
Input Voltage  
Driver ....................................... 0.3V to VCC + 0.3V  
Receiver ............................................... – 25V to 25V  
On/Off Pin.................................. 0.3V to VCC + 0.3V  
Output Voltage  
TOP VIEW  
NUMBER  
+
V
1
2
3
4
5
6
7
8
9
28  
V
+
V
27 C2  
26 C2  
CC  
+
C1  
C1  
LTC1337CG  
LTC1337CN  
LTC1337CS  
25 DR1 IN  
24 RX1 OUT  
23 DR2 IN  
22 RX2 OUT  
21 RX3 OUT  
20 RX4 OUT  
19 DR3 IN  
18 RX5 OUT  
17 GND  
DR1 OUT  
RX1 IN  
Driver .................................................... – 25V to 25V  
Receiver .................................... – 0.3V to VCC + 0.3V  
Short Circuit Duration  
DR2 OUT  
RX2 IN  
RX3 IN  
V+ ................................................................... 30 sec  
V................................................................... 30 sec  
Driver Output.............................................. Indefinite  
Receiver Output.......................................... Indefinite  
Operating Temperature Range  
RX4 IN 10  
DR3 OUT 11  
RX5 IN 12  
ON/OFF 13  
16 NC  
NC  
14  
15 NC  
G PACKAGE  
N PACKAGE  
28-LEAD PLASTIC DIP  
Commercial (LTC1337C) ........................ 0°C to 70°C  
Storage Temperature Range ................ – 65°C to 150°C  
Lead Temperature (Soldering, 10 sec)................. 300°C  
28-LEAD SSOP  
S PACKAGE  
28-LEAD PLASTIC SOL  
TJMAX = 125°C, θJA = 96°C/W (G)  
TJMAX = 125°C, θJA = 56°C/W (N)  
JMAX = 125°C, θJA = 85°C/W (S)  
T
Consult factory for Industrial and Military grade parts.  
DC ELECTRICAL CHARACTERISTICS V  
CC = 5V, C1 = C2 = C3 = C4 = 0.1µF, unless otherwise noted.  
PARAMETER  
CONDITIONS  
MIN  
TYP  
MAX  
UNITS  
Any Driver  
Output Voltage Swing  
R = 3k to GND  
R = 3k to GND  
L
Positive  
Negative  
5.0  
5.0  
7.0  
– 6.5  
V
V
L
Logic Input Voltage Level  
Logic Input Current  
Input Low Level (V  
Input High Level (V  
= High)  
= Low)  
1.4  
1.4  
0.8  
V
V
µA  
µA  
OUT  
2.0  
OUT  
V
IN  
V
IN  
= 5V  
= 0  
5
–5  
Output Short-Circuit Current  
Output Leakage Current  
Any Receiver  
V
= 0V  
±10  
10  
mA  
µA  
OUT  
SHUTDOWN, V  
= ±20V (Note 3)  
200  
OUT  
Input Voltage Thresholds  
Input Low Threshold  
Input High Threshold  
0.8  
1.3  
1.7  
0.4  
5
0.2  
4.8  
V
V
V
kΩ  
V
V
2.4  
1
7
Hysteresis  
Input Resistance  
Output Voltage  
0.1  
3
Output Low, I  
= – 1.6mA (V = 5V)  
= 160µA (V = 5V)  
0.4  
OUT  
CC  
Output High, I  
3.5  
OUT  
CC  
Output Short-Circuit Current  
Output Leakage Current  
Sourcing Current, V  
= 0  
15  
15  
20  
40  
1
mA  
mA  
µA  
OUT  
Sinking Current, V  
= V  
OUT  
CC  
SHUTDOWN, 0 V  
V (Note 3)  
10  
OUT  
CC  
2
LTC1337  
DC ELECTRICAL CHARACTERISTICS V  
CC = 5V, C1 = C2 = C3 = C4 = 0.1µF, unless otherwise noted.  
PARAMETER  
CONDITIONS  
MIN  
TYP  
MAX  
UNITS  
Power Supply Generator  
+
V Output Voltage  
I
I
I
I
= 0mA  
= 12mA  
= 0mA  
= 12mA  
8.0  
7.5  
8.0  
6.5  
V
V
V
V
OUT  
OUT  
V Output Voltage  
OUT  
OUT  
Supply Rise Time  
SHUTDOWN to Turn-On  
0.2  
ms  
Power Supply  
V
Supply Current  
No Load (Note 2)  
SHUTDOWN (Note 3)  
0.3  
1
1.4  
1.4  
0.5  
10  
0.8  
mA  
µA  
V
CC  
Supply Leakage Current (V  
On/Off Threshold Low  
On/Off Threshold High  
)
CC  
2.0  
V
AC CHARACTERISTICS  
PARAMETER  
CONDITIONS  
MIN  
TYP  
MAX  
UNITS  
Slew Rate  
R = 3k, C = 51pF  
8
4
30  
V/µs  
V/µs  
L
L
R = 3k, C = 2500pF  
2
L
L
Driver Propagation Delay  
(TTL to RS232)  
Receiver Propagation Delay  
(RS232 to TTL)  
t
t
t
t
(Figure 1)  
2
2
0.3  
0.2  
3
3
0.6  
0.6  
µs  
µs  
µs  
µs  
HLD  
LHD  
HLR  
LHR  
(Figure 1)  
(Figure 2)  
(Figure 2)  
Note 2: Supply current is measured with driver and receiver outputs  
The  
denotes specifications which apply over the operating temperature  
unloaded and driver inputs tied high.  
range (0°C T 70°C).  
A
Note 3: Supply current and leakage measurements in SHUTDOWN are  
Note 1: Absolute maximum ratings are those values beyond which the life  
performed with V = 0V.  
of the device may be impaired.  
ON  
U W  
TYPICAL PERFOR A CE CHARACTERISTICS  
Driver Output Voltage  
Receiver Input Thresholds  
Supply Current vs Data Rate  
10  
8
45  
40  
35  
30  
25  
20  
15  
10  
5
2.0  
1.9  
1.8  
1.7  
1.6  
1.5  
1.4  
1.3  
1.2  
1.1  
R
L
= 3k  
OUTPUT HIGH  
= 5V  
V
= 5V  
CC  
R
= 3k  
L
L
V
CC  
C
= 2500pF  
6
INPUT HIGH  
3 DRIVERS ACTIVE  
V
= 4.5V  
CC  
4
2
0
INPUT LOW  
–2  
–4  
–6  
–8  
OUTPUT LOW  
= 4.5V  
V
CC  
V
= 5V  
50  
CC  
0
30  
75  
DATA RATE (k BAUD)  
0
10  
20  
40  
60  
70  
30  
TEMPERATURE (°C)  
0
25  
50  
100 125 150 175  
0
10  
20  
40  
50  
60  
70  
TEMPERATURE (°C)  
1337 G01  
1337 G03  
1337 G02  
3
LTC1337  
TYPICAL PERFOR A CE CHARACTERISTICS  
U W  
Driver Leakage in SHUTDOWN  
VCC Supply Current  
Driver Short-Circuit Current  
45  
40  
35  
30  
25  
20  
15  
10  
5
20  
16  
14  
12  
10  
8
20  
18  
16  
14  
12  
10  
8
3 DRIVERS LOADED  
R
L
= 3k  
V
OUT  
= –20V  
I
I
SC  
1 DRIVER LOADED  
+
6
SC  
R
L
= 3k  
4
6
V
= 20V  
50  
OUT  
2
4
0
0
2
30  
0
10  
20  
40  
60  
70  
30  
TEMPERATURE (°C)  
30  
TEMPERATURE (°C)  
0
10  
20  
40  
50  
60  
70  
0
10  
20  
40  
50  
60  
70  
TEMPERATURE (°C)  
1337 G05  
1337 G04  
1337 G06  
Driver Output Waveforms  
Receiver Short-Circuit Current  
Receiver Output Waveforms  
55  
50  
45  
40  
35  
30  
25  
20  
15  
10  
DRIVER  
OUTPUT  
RX  
OUTPUT  
L = 50pF  
R
L = 3k  
C
L = 2500pF  
I
C
SC  
DRIVER  
OUTPUT  
R
L = 3k  
INPUT  
+
I
INPUT  
SC  
30  
0
10  
20  
40  
50  
60  
70  
TEMPERATURE (°C)  
1337 G07  
U
U
U
PI FU CTIO S  
VCC: 5V Input Supply Pin. Supply current less than 1µA in  
the SHUTDOWN mode. This pin should be decoupled with  
a 0.1µF ceramic capacitor.  
leled into common capacitors. For large numbers of  
devices,increasingthesizeofthesharedcommonstorage  
capacitors is recommended to reduce ripple.  
V: Negative Supply Output (RS232 Drivers). V(2VCC  
–1.5V). This pin requires an external capacitor C = 0.1µF  
for charge storage.  
C1+,C1,C2+,C2:CommutatingCapacitorInputs.These  
pins require two external capacitors C = 0.1µF. One from  
C1+ to C1, and another from C2+ to C2. To maintain  
charge pump efficiency, the capacitor’s effective series  
resistance should be less than 50.  
GND: Ground Pin.  
ON/OFF: TTL/CMOS Compatible Shutdown Pin. A logic  
low puts the device in the SHUTDOWN mode which  
reduces input supply current to less than 1µA and places  
all drivers and receivers in high impedance state.  
V+: Positive Supply Output (RS232 Drivers). V+ 2VCC  
1V. This pin requires an external capacitor C = 0.1µF for  
chargestorage. Thecapacitormaybetiedtogroundor5V.  
With multiple devices, the V + and Vpins may be paral-  
4
LTC1337  
U
U
U
PI FU CTIO S  
DRIVER IN: RS232 Driver Input Pins. Inputs are TTL/  
CMOS compatible. Inputs should not be allowed to float.  
Tie unused inputs to VCC.  
RX IN: Receiver Inputs. These pins can be forced to ±25V  
withoutdamage. Thereceiverinputsareprotectedagainst  
ESD to ±10kV for human body model discharges. Each  
receiver provides 0.4V of hysteresis for noise immunity.  
DRIVER OUT: Driver Outputs at RS232 Voltage Levels.  
Outputs are in a high impedance state when in SHUT-  
DOWNmodeorVCC =0V. Thedriveroutputsareprotected  
against ESD to ±10kV for human body model discharges.  
RX OUT: Receiver Outputs with TTL/CMOS Voltage Lev-  
els. Outputs are in a high impedance state when in SHUT-  
DOWN mode to allow data line sharing.  
U
W
W
SWITCHI G TI E WAVEFOR S  
V
V
CC  
CC  
1.7V  
DRIVER  
RX IN  
1.3V  
1.4V  
1.4V  
INPUT  
0V  
V
0V  
+
V
CC  
RX  
OUTPUT  
DRIVER  
OUTPUT  
0V  
0V  
0V  
0.8V  
V
0V  
t
t
t
LHR  
t
LHD  
HLR  
HLD  
1337 F02  
1337 F01  
Figure 1. Driver Propagation Delay Timing  
Figure 2. Receiver Propagation Delay Timing  
TEST CIRCUITS  
ESD Test Circuit  
DRIVER  
OUTPUT  
DRIVER  
DRIVER  
INPUT  
+
V
1
2
28  
27  
26  
25  
24  
23  
22  
21  
20  
19  
18  
17  
16  
15  
V
V
51pF  
3k  
LTC1337  
C1  
0.1µF  
C4  
0.1µF  
CC  
C3  
0.1µF  
3
C2  
0.1µF  
1337 F03  
4
DRIVER 1 IN  
RX1 OUT  
DRIVER 2 IN  
RX2 OUT  
RX3 OUT  
RX4 OUT  
DRIVER 3 IN  
RX5 OUT  
GND  
5
Figure 3. Driver Timing Test Load  
DRIVER 1 OUT  
RX1 IN  
6
7
RS232  
DRIVER 2 OUT  
RX2 IN  
8
LINE PINS  
PROTECTED  
TO ±10kV  
9
RX  
RX3 IN  
OUTPUT  
10  
11  
12  
13  
14  
RX4 IN  
RX IN  
RX  
DRIVER 3 OUT  
RX5 IN  
51pF  
ON/OFF  
1337 F04  
1337 TC01  
Figure 4. Receiver Timing Test Load  
5
LTC1337  
TYPICAL APPLICATI S  
U
O
Operation Using 5V and 12V Power Supplies  
+
V
1
2
28  
27  
26  
25  
24  
23  
22  
21  
20  
19  
18  
17  
16  
15  
V
V
LTC1337  
+
CC  
+
C2  
0.1µF  
C2  
5V V  
CC  
C1  
3
+
12V V  
+
0.1µF  
4
+
0.01µF  
0.01µF  
C1  
DRIVER IN  
RX OUT  
DRIVER IN  
RX OUT  
RX OUT  
RX OUT  
DRIVER IN  
RX OUT  
GND  
5
DRIVER OUT  
RX IN  
6
7
DRIVER OUT  
RX IN  
TO LOGIC  
8
TO LINE  
9
RX IN  
10  
11  
12  
13  
14  
RX IN  
DRIVER OUT  
RX IN  
ON/0FF = 5V  
1337 TA03  
Typical Mouse Driving Application  
+
V
1
2
28  
27  
26  
25  
24  
23  
22  
21  
20  
19  
18  
17  
16  
15  
V
+
LTC1337  
+
C2  
0.1µF  
0.1µF  
5V V  
+
0.1µF  
CC  
+
MOUSE  
C1  
3
C2  
0.1µF  
DRIVER IN  
RX OUT  
DRIVER IN  
RX OUT  
RX OUT  
RX OUT  
DRIVER IN  
RX OUT  
GND  
4
C1  
LOGIC “0”  
LOGIC “0”  
+
V
5
DRIVER OUT  
RX IN  
LOGIC  
6
DCD  
(1)  
7
DSR  
RX  
DRIVER OUT  
RX IN  
8
MOUSE DATA  
LOGIC “1”  
9
RTS  
TX  
RX IN  
OPTICS  
10  
11  
12  
13  
14  
RX IN  
CTS  
DTR  
RI  
DRIVER OUT  
RX IN  
V
ON/OFF  
(9)  
(5)  
1137 TA04  
DB9  
6
LTC1337  
U
Dimensions in inches (millimeters) unless otherwise notes.  
G Package  
PACKAGE DESCRIPTIO  
28-Lead SSOP  
0.397 – 0.407  
(10.07 – 10.33)  
0.205 – 0.212  
(5.20 – 5.38)  
0.066 – 0.070  
(1.68 – 1.78)  
0.068 – 0.078  
(1.73 – 1.99)  
28 27 26 25 24 23 22 21 20 19 18  
16 15  
17  
PARTING  
LINE  
0° – 8°  
0.301 – 0.311  
(7.65 – 7.90)  
0.045  
(1.14)  
0.0256  
(0.65)  
BSC  
0.022 – 0.037  
(0.55 – 0.95)  
0.005 – 0.009  
(0.13 – 0.22)  
0.002 – 0.008  
(0.05 – 0.21)  
0.010 – 0.015  
(0.25 – 0.38)  
5
7
8
1
2
3
4
6
9 10 11 12 13 14  
0.045  
(1.14)  
N Package  
28-Lead Plastic DIP  
1.455  
(36.957)  
MAX  
0.070  
(1.778)  
TYP  
0.020  
(0.508)  
TYP  
0.600 – 0.625  
(15.240 – 15.875)  
0.130 ± 0.005  
(3.302 ± 0.127)  
0.045 – 0.055  
(1.143 – 1.651)  
28 27 26 25 24 23 22 21 20 19 18 17 16 15  
0.020  
(0.508)  
MIN  
0.505 – 0.560  
(12.827 – 14.224)  
95° ± 5°  
0.009 – 0.015  
(0.229 – 0.381)  
+0.025  
0.125  
(3.175)  
MIN  
0.035 – 0.080  
(0.889 – 2.032)  
0.100 ± 0.010  
(2.540 ± 0.254)  
0.625  
0.018 ± 0.003  
(0.457 ± 0.076)  
–0.015  
+0.635  
1
2
3
5
7
9
4
6
8
10 11 12 13 14  
15.87  
)
(
–0.381  
S Package  
28-Lead SOL  
0.697 – 0.712  
(17.70 – 18.08)  
28 27 26 25 24 23 22 21 20 19 18  
0.291 – 0.299  
(7.391 – 7.595)  
0.037 – 0.045  
(0.940 – 1.143)  
16 15  
17  
0.093 – 0.104  
(2.362 – 2.642)  
0.005  
0.010 – 0.029  
(0.254 – 0.737)  
× 45°  
(0.127)  
RAD MIN  
0° – 8° TYP  
SEE  
NOTE  
0.050  
(1.270)  
TYP  
0.394 – 0.419  
(10.007 – 10.643)  
0.014 – 0.019  
(0.356 – 0.482)  
0.009 – 0.013  
(0.229 – 0.330)  
0.004 – 0.012  
(0.102 – 0.305)  
SEE NOTE  
0.016 – 0.050  
(0.406 – 1.270)  
NOTE:  
PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS.  
THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS.  
2
3
5
7
8
9 10 11 12 13 14  
1
4
6
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.  
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-  
tationthattheinterconnectionofitscircuitsasdescribedhereinwillnotinfringeonexistingpatentrights.  
7
LTC1337  
U.S. Area Sales Offices  
SOUTHEAST REGION  
Linear Technology Corporation  
17060 Dallas Parkway  
Suite 208  
Dallas, TX 75248  
Phone: (214) 733-3071  
FAX: (214) 380-5138  
SOUTHWEST REGION  
Linear Technology Corporation  
22141 Ventura Blvd.  
NORTHEAST REGION  
Linear Technology Corporation  
One Oxford Valley  
2300 E. Lincoln Hwy.,Suite 306  
Langhorne, PA 19047  
Suite 206  
Woodland Hills, CA 91364  
Phone: (818) 703-0835  
FAX: (818) 703-0517  
Phone: (215) 757-8578  
FAX: (215) 757-5631  
CENTRAL REGION  
Linear Technology Corporation  
Chesapeake Square  
NORTHWEST REGION  
Linear Technology Corporation  
782 Sycamore Dr.  
Linear Technology Corporation  
266 Lowell St., Suite B-8  
Wilmington, MA 01887  
229 Mitchell Court, Suite A-25  
Addison, IL 60101  
Phone: (708) 620-6910  
FAX: (708) 620-6977  
Milpitas, CA 95035  
Phone: (408) 428-2050  
FAX: (408) 432-6331  
Phone: (508) 658-3881  
FAX: (508) 658-2701  
International Sales Offices  
KOREA  
TAIWAN  
FRANCE  
Linear Technology Korea Branch  
Namsong Building, #505  
Itaewon-Dong 260-199  
Yongsan-Ku, Seoul  
Korea  
Linear Technology Corporation  
Rm. 801, No. 46, Sec. 2  
Chung Shan N. Rd.  
Taipei, Taiwan, R.O.C.  
Phone: 886-2-521-7575  
FAX: 886-2-562-2285  
Linear Technology S.A.R.L.  
Immeuble "Le Quartz"  
58 Chemin de la Justice  
92290 Chatenay Malabry  
France  
Phone: 82-2-792-1617  
FAX: 82-2-792-1619  
Phone: 33-1-41079555  
FAX: 33-1-46314613  
UNITED KINGDOM  
SINGAPORE  
Linear Technology (UK) Ltd.  
The Coliseum, Riverside Way  
Camberley, Surrey GU15 3YL  
United Kingdom  
Phone: 44-276-677676  
FAX: 44-276-64851  
GERMANY  
Linear Techonolgy GMBH Untere  
Hauptstr. 9  
D-85386 Eching  
Germany  
Linear Technology Pte. Ltd.  
101 Boon Keng Road  
#02-15 Kallang Ind. Estates  
Singapore 1233  
Phone: 65-293-5322  
FAX: 65-292-0398  
Phone: 49-89-3197410  
FAX: 49-89-3194821  
JAPAN  
Linear Technology KK  
5F YZ Bldg.  
Iidabashi, Chiyoda-Ku  
Tokyo, 102 Japan  
Phone: 81-3-3237-7891  
FAX: 81-3-3237-8010  
World Headquarters  
Linear Technology Corporation  
1630 McCarthy Blvd.  
Milpitas, CA 95035-7487  
Phone: (408) 432-1900  
FAX: (408) 434-0507  
LT/GP 0893 10K REV 0 • PRINTED IN USA  
Linear Technology Corporation  
1630 McCarthy Blvd., Milpitas, CA 95035-7487  
8
LINEAR TECHNOLOGY CORPORATION 1993  
(408) 432-1900 FAX: (408) 434-0507 TELEX: 499-3977  

相关型号:

LTC1337CNW

5V Low Power RS232 3-Driver/5-Receiver Transceiver
Linear

LTC1337CNW#PBF

LTC1337 - 5V Low Power RS232 3-Driver/5-Receiver Transceiver; Package: PDIP; Pins: 28; Temperature Range: 0°C to 70°C
Linear

LTC1337CS

5V Low Power RS232 3-Driver/5-Receiver Transceiver
Linear

LTC1337CSW

5V Low Power RS232 3-Driver/5-Receiver Transceiver
Linear

LTC1337CSW#PBF

LTC1337 - 5V Low Power RS232 3-Driver/5-Receiver Transceiver; Package: SO; Pins: 28; Temperature Range: 0°C to 70°C
Linear

LTC1337CSW#TRPBF

LTC1337 - 5V Low Power RS232 3-Driver/5-Receiver Transceiver; Package: SO; Pins: 28; Temperature Range: 0°C to 70°C
Linear

LTC1337_1

5V Low Power RS232 3-Driver/5-Receiver Transceiver
Linear

LTC1338

5V Low Power RS232 5-Driver/3-Receiver Transceiver
Linear

LTC1338C

5V Low Power RS232 5-Driver/3-Receiver Transceiver
Linear

LTC1338CG

5V Low Power RS232 5-Driver/3-Receiver Transceiver
Linear

LTC1338CG#TR

LTC1338 - 5V Low Power RS232 5-Driver/3-Receiver Transceiver; Package: SSOP; Pins: 28; Temperature Range: 0°C to 70°C
Linear

LTC1338CN

5V Low Power RS232 5-Driver/3-Receiver Transceiver
Linear