LT1640AHIN8 [Linear]
Negative Voltage Hot Swap Controller; 负电压热插拔控制器型号: | LT1640AHIN8 |
厂家: | Linear |
描述: | Negative Voltage Hot Swap Controller |
文件: | 总16页 (文件大小:317K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LT1640AL/LT1640AH
Negative Voltage
Hot Swap Controller
U
FEATURES
DESCRIPTIO
The LT®1640AL/LT1640AH are 8-pin, negative voltage
Hot SwapTM controllers that allow a board to be safely
inserted and removed from a live backplane. Inrush cur-
rent is limited to a programmable value by controlling the
gate voltage of an external N-channel pass transistor. The
pass transistor is turned off if the input voltage is less than
the programmable undervoltage threshold or greater than
the overvoltage threshold. A programmable electronic
circuit breaker protects the system against shorts. The
PWRGD (LT1640AL) or PWRGD (LT1640AH) signal can
be used to directly enable a power module. The LT1640AL
is designed for modules with a low enable input and the
LT1640AH for modules with a high enable input.
■
Allows Safe Board Insertion and Removal
from a Live –48V Backplane
■
Operates from –10V to –80V
■
Programmable Inrush Current
■
Allows 50mA of Reverse Drain Pin Current
■
Programmable Electronic Circuit Breaker
■
Programmable Overvoltage Protection
■
Programmable Undervoltage Lockout
■
Power Good Control Output
U
APPLICATIO S
■
Central Office Switching
■
–48V Distributed Power Systems
The LT1640AL/LT1640AH are available in 8-pin PDIP and
SO packages.
, LTC and LT are registered trademarks of Linear Technology Corporation.
Hot Swap is a trademark of Linear Technology Corporation.
■
Negative Power Supply Control
U
TYPICAL APPLICATIO
(SHORT PIN)
GND
Input Inrush Current
GND
R4†
8
562k
V
DD
CONTACT
BOUNCE
1%
3
2
UV = 37V
OV = 71V
UV
OV
R5†
9.09k
1%
1
LT1640AL
PWRGD
R6†
10k
1%
V
SENSE
5
GATE
6
DRAIN
7
EE
4
*
C1†
150nF
25V
R3†
18k
5%
R2
10Ω
5%
C2†
3.3nF
100V
R1†
0.02Ω
5%
3
4
–48V
2
1
2
Q1
IRF530
ON/OFF
1
9
8
+
–
+
+
5V
V
V
V
IN
OUT
SENSE
* DIODES INC. SMAT70A
C3
+
C4
+
C5
† THESE COMPONENTS ARE APPLICATION
SPECIFIC AND MUST BE SELECTED BASED
7
6
5
0.1µF
100µF
TRIM
–
100µF
16V
100V
100V
UPON OPERATING CONDITIONS AND DESIRED
PERFORMANCE. SEE APPLICATIONS
INFORMATION.
SENSE
4
–
V
IN
OUT
1640A F07b
1640A TA01
LUCENT
JW050A1-E
1
LT1640AL/LT1640AH
W W
U W
ABSOLUTE MAXIMUM RATINGS
(Note 1), All Voltages Referred to VEE
Supply Voltage (VDD – VEE) .................... –0.3V to 100V
PWRGD, PWRGD Pins ........................... –0.3V to 100V
DRAIN Pin ................................................. –2V to 100V
SENSE, GATE Pins.................................... –0.3V to 20V
UV, OV Pins .............................................. –0.3V to 60V
Maximum Junction Temperature ......................... 125°C
Operating Temperature Range
LT1640ALC/LT1640AHC ........................ 0°C to 70°C
LT1640ALI/LT1640AHI...................... –40°C to 85°C
Storage Temperature Range ................ –65°C to 150°C
Lead Temperature (Soldering, 10 sec)................. 300°C
W
U
/O
PACKAGE RDER I FOR ATIO
ORDER PART
ORDER PART
NUMBER
NUMBER
TOP VIEW
TOP VIEW
PWRGD
OV
1
2
3
4
8
7
6
5
V
DD
PWRGD
OV
1
2
3
4
8
7
6
5
V
DD
LT1640ALCN8
LT1640ALCS8
LT1640ALIN8
LT1640ALIS8
LT1640AHCN8
LT1640AHCS8
LT1640AHIN8
LT1640AHIS8
DRAIN
GATE
DRAIN
GATE
UV
UV
V
SENSE
V
SENSE
EE
EE
N8 PACKAGE
8-LEAD PDIP
S8 PACKAGE
N8 PACKAGE
8-LEAD PDIP
S8 PACKAGE
8-LEAD PLASTIC SO
8-LEAD PLASTIC SO
S8 PART MARKING
S8 PART MARKING
TJMAX = 125°C, θJA = 120°C/W (N8)
JMAX = 125°C, θJA = 150°C/W (S8)
TJMAX = 125°C, θJA = 120°C/W (N8)
TJMAX = 125°C, θJA = 150°C/W (S8)
T
1640AL
640ALI
1640AH
640AHI
Consult factory for parts specified with wider operating temperature ranges.
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 2), VDD = 48V, VEE = 0V unless otherwise noted.
SYMBOL PARAMETER
DC
CONDITIONS
MIN
TYP
MAX
UNITS
V
Supply Operating Range
Supply Current
●
●
●
●
10
80
5
V
mA
mV
µA
DD
I
UV = 3V, OV = V , SENSE = V
EE
1.3
50
DD
EE
V
Circuit Breaker Trip Voltage
GATE Pin Pull-Up Current
GATE Pin Pull-Down Current
SENSE Pin Current
V
= (V
– V )
40
–30
24
60
–60
70
CB
CB
SENSE
EE
I
I
I
Gate Drive On, V
= V
EE
–45
50
PU
GATE
Any Fault Condition
= 50mV
mA
µA
PD
V
–20
SENSE
SENSE
∆V
GATE
External Gate Drive
(V
GATE
(V
GATE
– V ), 15V ≤ V ≤ 80V
●
●
10
6
13.5
8
18
15
V
V
EE
DD
– V ), 10V ≤ V < 15V
EE
DD
V
V
V
UV Pin High Threshold Voltage
UV Pin Low Threshold Voltage
UV Pin Hysteresis
UV Low to High Transition
UV High to Low Transition
●
●
1.213
1.198
1.243
1.223
20
1.272
1.247
V
V
UVH
UVL
UVHY
INUV
mV
µA
V
I
UV Pin Input Current
V
= V
●
●
●
–0.02
1.223
1.203
20
–0.5
1.247
1.232
UV
EE
V
V
V
OV Pin High Threshold Voltage
OV Pin Low Threshold Voltage
OV Pin Hysteresis
OV Low to High Transition
OV High to Low Transition
1.198
1.165
OVH
OVL
V
mV
µA
OVHY
INOV
I
OV Pin Input Current
V
= V
●
–0.03
–0.5
OV
EE
2
LT1640AL/LT1640AH
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 2), VDD = 48V, VEE = 0V unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
1.4
0.4
50
MAX
UNITS
V
V
Power Good Threshold
V
– V , High to Low Transition
1.1
2.0
V
V
PG
DRAIN
DRAIN
EE
Power Good Threshold Hysteresis
Drain Input Bias Current
PGHY
DRAIN
I
V
= 48V
●
●
10
500
µA
V
PWRGD Output Low Voltage
PWRGD (LT1640AL), (V
– V ) < V
OL
DRAIN
EE
PG
I
I
= 1mA
= 5mA
0.48
1.50
0.8
3.0
V
V
OUT
OUT
PWRGD Output Low Voltage
(PWRGD – DRAIN)
PWRGD (LT1640AH), V
= 5V
DRAIN
I
= 1mA
●
●
0.75
0.05
1.0
10
V
OUT
I
Output Leakage
PWRGD (LT1640AL), V
= 80V
=48V,
µA
OH
DRAIN
V
PWRGD
R
Power Good Output Impedance
(PWRGD to DRAIN)
PWRGD (LT1640AH), (V
– V ) < V
PG
●
2
2
6.5
kΩ
OUT
DRAIN
EE
AC
t
t
t
t
t
t
OV High to GATE Low
UV Low to GATE Low
OV Low to GATE High
UV High to GATE High
SENSE High to Gate Low
Figures 1, 2
Figures 1, 3
Figures 1, 2
Figures 1, 3
Figures 1, 4
1.7
1.5
5.5
6.5
3
µs
µs
µs
µs
µs
PHLOV
PHLUV
PLHOV
PLHUV
PHLSENSE
PHLPG
4
DRAIN Low to PWRGD Low
DRAIN Low to (PWRGD – DRAIN) High
(LT1640AL) Figures 1, 5
(LT1640AH) Figures 1, 5
0.5
0.5
µs
µs
t
DRAIN High to PWRGD High
DRAIN High to (PWRGD – DRAIN) Low
(LT1640AL) Figures 1, 5
(LT1640AH) Figures 1, 5
0.5
0.5
µs
µs
PLHPG
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: All currents into device pins are positive; all currents out of device
pins are negative. All voltages are referenced to V unless otherwise
EE
specified.
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Supply Current vs Supply Voltage
Supply Current vs Temperature
Gate Voltage vs Supply Voltage
1.6
1.5
1.4
1.3
1.2
1.1
1.0
15
14
13
12
11
10
9
1.8
1.7
1.6
1.5
V
= 48V
T
= 25°C
DD
T
= 25°C
A
A
1.4
1.3
1.2
1.1
0
8
7
6
–50 –25
0
25
50
75
100
20
40
SUPPLY VOLTAGE (V)
80
0
20
60
SUPPLY VOLTAGE (V)
80
100
0
100
40
60
TEMPERATURE (°C)
1640A G02
1640A G03
1640A G01
3
LT1640AL/LT1640AH
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Circuit Breaker Trip Voltage
Gate Pull-Up Current
vs Temperature
Gate Voltage vs Temperature
vs Temperature
15.0
14.5
48
47
46
45
44
43
42
41
40
55
54
V
= 48V
DD
V
= 0V
GATE
53
14.0
13.5
52
51
50
49
13.0
12.5
12.0
48
–50 –25
0
25
50
75
100
–50
0
25
50
75
100
–25
75
–50
–25
0
25
50
100
TEMPERATURE (°C)
TEMPERATURE (°C)
TEMPERATURE (°C)
1640A G04
1640A G05
1640A G06
Gate Pull-Down Current
vs Temperature
PWRGD Output Impedance
vs Temperature (LT1640AH)
PWRGD Output Low Voltage
vs Temperature (LT1640AL)
8
7
55
52
49
0.5
0.4
0.3
0.2
0.1
0
V
– V > 2.4V
EE
V
= 2V
I
= 1mA
DRAIN
GATE
OUT
6
5
46
43
40
4
3
2
–50 –25
0
25
50
75
100
–50 –25
0
25
50
75
100
–50 –25
0
25
50
75
100
TEMPERATURE (°C)
TEMPERATURE (°C)
TEMPERATURE (°C)
1640A G09
1640A G07
1640A G08
U
U
U
PI FU CTIO S
PWRGD/PWRGD(Pin1):PowerGoodOutputPin.Thispin
will toggle when VDRAIN is within VPG of VEE. This pin can
be connected directly to the enable pin of a power module.
When the DRAIN pin of the LT1640AH is above VEE by
more than VPG, the PWRGD pin will sink current to the
DRAIN pin which pulls the module’s enable pin low,
forcing it off. When VDRAIN drops below VPG, the PWRGD
sink current is turned off and a 6.5k resistor is connected
between PWRGD and DRAIN, allowing the module’s pull-
up current to pull the enable pin high and turn on the
module.
When the DRAIN pin of the LT1640AL is above VEE by
more than VPG, the PWRGD pin will be high impedance,
allowing the pull-up current of the module’s enable pin to
pull the pin high and turn the module off. When VDRAIN
drops below VPG, the PWRGD pin sinks current to VEE,
pulling the enable pin low and turning on the module.
4
LT1640AL/LT1640AH
U
U
U
PIN FUNCTIONS
OV (Pin 2): Analog Overvoltage Input. When OV is pulled If the circuit breaker trip current is set to twice the normal
above the 1.223V low-to-high threshold, an overvoltage operating current, only 25mV is dropped across the
conditionisdetectedandtheGATEpinwillbeimmediately sense resistor during normal operation. To disable the
pulled low. The GATE pin will remain low until OV drops circuit breaker, VEE and SENSE can be shorted together.
below the 1.203V high-to-low threshold.
GATE (Pin 6): Gate Drive Output for the External
UV (Pin 3): Analog Undervoltage Input. When UV is N-Channel. The GATE pin will go high when the following
pulled below the 1.223V high to low threshold, an under- start-upconditionsaremet:theUVpinishigh, theOVpin
voltage condition is detected and the GATE pin will be is low and (VSENSE – VEE) < 50mV. The GATE pin is pulled
immediately pulled low. The GATE pin will remain low high by a 45µA current source and pulled low with a
until UV rises above the 1.243 low-to-high threshold.
50mA current source.
The UV pin is also used to reset the electronic circuit DRAIN (Pin 7): Analog Drain Sense Input. Connect this
breaker. If the UV pin is cycled low and high following the pin to the drain of the external N-channel and the V– pin
trip of the circuit breaker, the circuit breaker is reset and of the power module. When the DRAIN pin is below VPG,
a normal power-up sequence will occur.
the PWRGD or PWRGD pin will toggle. In some condi-
tions, the DRAIN pin is pulled below VEE. The part is not
damaged if the reverse DRAIN pin current is limited to
50mA.
VEE (Pin 4): Negative Supply Voltage Input. Connect to
the lower potential of the power supply.
SENSE (Pin 5): Circuit Breaker Sense Pin. With a sense
resistor placed in the supply path between VEE and
SENSE, the circuit breaker will trip when the voltage
across the resistor exceeds 50mV. Noise spikes of less
than 2µs are filtered out and will not trip the circuit
breaker.
VDD (Pin 8): Positive Supply Voltage Input. Connect this
pin to the higher potential of the power supply inputs and
the V+ pin of the power module. The input supply voltage
ranges from 10V to 80V.
W
BLOCK DIAGRA
V
DD
–
UV
V
CC
V
AND
CC
REFERENCE
GENERATOR
REF
+
OUTPUT
DRIVE
PWRGD/PWRGD
REF
–
LOGIC
AND
GATE DRIVE
+
50mV
OV
–
+
–
+
–
+
+
V
PG
–
V
EE
1640A BD
V
EE
SENSE
GATE
DRAIN
5
LT1640AL/LT1640AH
TEST CIRCUIT
R
5k
+
V
PWRGD/PWRGD
OV
V
DD
5V
+
–
48V
DRAIN
V
OV
V
V
DRAIN
LT1640AL/LT1640AH
UV
GATE
V
UV
V
SENSE
EE
SENSE
1640A F01
Figure 1. Test Circuit
W U
W
TIMING DIAGRAMS
2V
1.223V
OV
2V
1.203V
1.223V
1.243V
UV
0V
0V
t
t
PLHOV
t
t
PHLOV
PHLUV
PLHUV
1V
GATE
GATE
1V
1V
1V
1640A F02
1640A F03
Figure 2. OV to GATE Timing
Figure 3. UV to GATE Timing
1.8V
1.4V
50mV
DRAIN
SENSE
GATE
V
EE
t
t
PLHPG
PHLPG
1V
t
PHLSENSE
1V
PWRGD
DRAIN
1V
V
EE
1640A F04
1.8V
0V
Figure 4. SENSE to GATE Timing
1.4V
t
t
PLHPG
1V
PHLPG
1V
PWRGD
1640A F05
V
– V
DRAIN
= 0V
PWRGD
Figure 5. DRAIN to PWRGD/PWRGD Timing
6
LT1640AL/LT1640AH
W U U
U
APPLICATIO S I FOR ATIO
Hot Circuit Insertion
Power Supply Ramping
Whencircuitboardsareinsertedintoalive –48Vbackplane,
the bypass capacitors at the input of the board’s power
module or switching power supply can draw huge tran-
sient currents as they charge up. The transient currents
can cause permanent damage to the board’s components
and cause glitches on the system power supply.
The input to the power module on a board is controlled by
placing an external N-channel pass transistor (Q1) in the
power path (Figure 6a, all waveforms are with respect to
the VEE pin of the LT1640A). R1 provides current fault
detection and R2 prevents high frequency oscillations.
Resistors R4, R5 and R6 provide undervoltage and over-
voltage sensing. By ramping the gate of Q1 up at a slow
rate, the surge current charging load capacitors C3 and C4
can be limited to a safe value when the board makes
connection.
The LT1640A is designed to turn on a board’s supply
voltage in a controlled manner, allowing the board to be
safely inserted or removed from a live backplane. The chip
also provides undervoltage, overvoltage and overcurrent
protection while keeping the power module off until its
input voltage is stable and within tolerance.
Resistor R3 and capacitor C2 act as a feedback network to
accurately control the inrush current. The inrush current
can be calculated with the following equation:
IINRUSH = (45µA • CL)/C2
where CL is the total load capacitance equal to C3 + C4 +
module input capacitance.
(SHORT PIN)
GND
GND
VICOR
8
R4
562k
1%
VI-J3D-CY
C3
0.1µF
100V
C4
100µF
100V
+
V
+
+
–
DD
5V
V
V
IN
OUT
3
2
UV = 37V
OV = 71V
UV
OV
+
C5
R5
9.09k
1%
1
LT1640AH
PWRGD
GATE IN
–
100µF
16V
V
V
R6
10k
1%
IN
OUT
V
SENSE
5
GATE
6
DRAIN
7
EE
4
R2
10Ω
5%
C1
150nF
25V
R3
18k
5%
*
C2
3.3nF
100V
R1
0.02Ω
5%
3
4
1640A F06a
–48V
* DIODES INC. SMAT70A
1
2
Q1
IRF530
Figure 6a. Inrush Control Circuitry
7
LT1640AL/LT1640AH
W U U
U
APPLICATIO S I FOR ATIO
Capacitor C1 and resistor R3 prevent Q1 from momen-
tarily turning on when the power pins first make contact.
Without C1 and R3, capacitor C2 would pull the gate of Q1
up to a voltage roughly equal to VEE • C2/CGS(Q1) before
the LT1640A could power up and actively pull the gate
low. By placing capacitor C1 in parallel with the gate
capacitance of Q1 and isolating them from C2 using
resistor R3, the problem is solved. The value of C1 should
be:
R3’svalueisnotcriticalandisgivenby(VINMAX +∆VGATE)/
5mA.
The waveforms are shown in Figure 6b. When the power
pins make contact, they bounce several times. While the
contacts are bouncing, the LT1640A senses an
undervoltage condition and the GATE is immediately
pulled low when the power pins are disconnected.
Once the power pins stop bouncing, the GATE pin starts to
ramp up. When Q1 turns on, the GATE voltage is held
constant by the feedback network of R3 and C2. When the
DRAIN voltage has finished ramping, the GATE pin then
ramps to its final value.
V
INMAX − VTH
• C2 + C
(
)
GD
VTH
where VTH is the MOSFET’s minimum gate threshold and
VINMAX is the maximum operating input voltage.
CONTACT
BOUNCE
Figure 6b. Inrush Control Waveforms
8
LT1640AL/LT1640AH
W U U
U
APPLICATIO S I FOR ATIO
Electronic Circuit Breaker
on R7. This voltage will be counted into the circuit breaker
trip voltage just as the voltage across the sense resistor.
A small resistor is recommended for R7. A 100Ω for R7
willcausea2mVerror.Thefollowingequationcanbeused
to estimate the delay time at the SENSE pin:
The LT1640A features an electronic circuit breaker func-
tion that protects against short circuits or excessive sup-
ply currents. By placing a sense resistor between the VEE
and SENSE pin, the circuit breaker will be tripped when-
ever the voltage across the sense resistor is greater than
50mV for more than 3µs as shown in Figure 7.
V(t)– V(tO)
t = –R •C •In 1–
V – V(tO)
i
Note that the circuit breaker threshold should be set
sufficiently high to account for the sum of the load current
andtheinrushcurrent.Iftheloadcurrentcanbecontrolled
bythePWRGD/PWRGDpin(asinFigure6a),thethreshold
can be set lower, since it will never need to accommodate
inrush current and load current simultaneously.
Where V(t) is the circuit breaker trip voltage, typically
50mV. V(tO) is the voltage drop across the sense resistor
before the short or overcurrent condition occurs. Vi is the
voltage across the sense resistor when the short current
or overcurrent is applied on it.
Whenthecircuitbreakertrips,theGATEpinisimmediately
pulled to VEE and the external N-channel turns off. The
GATE pin will remain low until the circuit breaker is reset
by pulling UV low, then high or cycling power to the part.
Example: A system has a 1A current load and a 0.02Ω
sense resistor is used. An extended delay circuit needs to
be designed for a 50µs delay time after the load jumps to
5A. In this case:
If more than 3µs deglitching time is needed to reject
current noise, an external resistor and capacitor can be
added to the sense circuit as shown in Figure 8. R7 and C3
act as a lowpass filter that will slow down the SENSE pin
voltage from rising too fast. Since the SENSE pin will
source current, typically 20µA, there will be a voltage drop
V(t) = 50mV
V(tO) = 20mV
Vi = 5A • 0.02Ω = 100mV
If we choose R = 100Ω, we will get C = 1µF.
(SHORT PIN)
GND
GND
8
R4
562k
V
DD
1%
3
2
UV
OV
UV = 37V
OV = 71V
R5
9.09k
1%
1
LT1640AL
PWRGD
+
C
L
100µF
R6
10k
1%
100V
V
EE
SENSE
5
GATE
6
DRAIN
7
4
C3
*
R7
R2
10Ω
5%
C1
150nF
25V
R3
18k
5%
C2
3.3nF
100V
R1
0.02Ω
5%
3
4
–48V
1640A F08
1
2
Q1
IRF530
1640A F07
* DIODES INC. SMAT70A
Figure 7. Short-Circuit Protection Waveforms
Figure 8. Extending the Short-Circuit Protection Delay
9
LT1640AL/LT1640AH
W U U
U
APPLICATIO S I FOR ATIO
Under some conditions, a short circuit at the output can
cause the input supply to dip below the UV threshold,
resetting the circuit breaker immediately.
Transistors Q2 and Q3 along with R7, R8, C4 and D1 form
a programmable one-shot circuit. Before a short occurs,
the GATE pin is pulled high and Q3 is turned on, pulling
node 2 to VEE. Resistor R8 turns off Q2. When a short
occurs, the GATE pin is pulled low and Q3 turns off. Node
2 starts to charge C4 and Q2 turns on, pulling the UV pin
low and resetting the circuit breaker. As soon as C4 is fully
charged, R8 turns off Q2, UV goes high and the GATE
starts to ramp up. Q3 turns back on and quickly pulls node
2 back to VEE. Diode D1 clamps node 3 one diode drop
below VEE. The duty cycle is set to 10% to prevent Q1 from
overheating.
The LT1640A then cycles on and off repeatedly until the
short is removed. This can be minimized by adding a
deglitching delay to the UV pin with a capacitor from UV to
VEE. This capacitor forms an RC time constant with the
resistorsatUV, allowingtheinputsupplytorecoverbefore
the UV pin resets the circuit breaker.
A circuit that automatically resets the circuit breaker after
a current fault is shown in Figure 9.
(SHORT PIN)
GND
GND
8
R7
1M
5%
R4
562k
1%
V
DD
2
3
2
UV
OV
C4
R5
9.09k
1%
1
1µF
LT1640AL
PWRGD
C3
100µF
100V
+
100V
R6
10k
1%
V
SENSE
5
GATE
6
DRAIN
7
EE
Q2
3
4
2N2222
*
Q3
ZVN3310
R2
10Ω
5%
C1
R3
18k
5%
C2
3.3nF
100V
150nF
25V
R8
510k
5%
R1
0.02Ω
5%
D1
1N4148
3
4
–48V
* DIODES INC. SMAT70A
1640A F09a
1
2
Q1
IRF530
1640A F09b
Figure 9. Automatic Restart After Current Fault
10
LT1640AL/LT1640AH
W U U
U
APPLICATIO S I FOR ATIO
Undervoltage and Overvoltage Detection
Figure 10a. With R4 = 562k, R5 = 9.09k and R6 = 10k, the
undervoltage threshold is set to 37V and the overvoltage
threshold is set to 71V. The resistor divider will also
amplify the 20mV hysteresis at the UV pin and OV pin to
0.6V and 1.2V at the input, respectively.
The UV (Pin 3) and OV (Pin 2) pins can be used to detect
undervoltage and overvoltage conditions at the power
supply input. The UV and OV pins are internally connected
toanalogcomparatorswith20mVofhysteresis. Whenthe
UV pin falls below its threshold or the OV pin rises above
its threshold, the GATE pin is immediately pulled low. The
GATE pin will be held low until UV is high and OV is low.
More hysteresis can be added to the UV threshold by
connecting resistor R3 between the UV pin and the GATE
pin as shown in Figure 10b.
The undervoltage and overvoltage trip voltages can be
programmed using a three resistor divider as shown in
(SHORT PIN)
GND
GND
8
R4
R5
R6
V
DD
3
2
R4 + R5+ R6
V
V
= 1.223
= 1.223
UV
OV
UV
OV
(
(
)
)
R5 + R6
LT1640AL
LT1640AH
R4 + R5+ R6
R6
V
EE
4
–48V
1640A F10a
Figure 10a. Undervoltage and Overvoltage Sensing
(SHORT PIN)
GND
GND
8
R4
506k
1%
V
DD
2
3
OV
UV = 37.6V
UV = 43V
OV = 71V
R1
562k
1%
LT1640AL/LT1640AH
UV
R5
R2
R3
V
3
SENSE
GATE
6
EE
8.87k 16.9k 1.62M
1%
1%
1%
4
5
R6
C1
10Ω
150nF
*
R1
5%
25V
0.02Ω
4
5%
–48V
1640A F10b
1
2
Q1
* DIODES INC. SMAT70A
IRF530
Figure 10b. Programmable Hysteresis for Undervoltage Detection
11
LT1640AL/LT1640AH
W U U
U
APPLICATIO S I FOR ATIO
Thenewthresholdvoltagewhentheinputmovesfromlow
to high is:
R4 + R5
VOV = VOVH
R5
R2 •R3 +R1•R3 +R1•R2
With R4 = 506k, R5 = 8.87k and VOVH = 1.223V, the
overvoltage threshold will be 71V.
V
UV,LH = V
UVH
R2 •R3
where VUVH is typically 1.243V.
PWRGD/PWRGD Output
The new threshold voltage when the input moves from
high to low is:
The PWRGD/PWRGD output can be used to directly en-
able a power module when the input voltage to the module
is within tolerance. The LT1640AL has a PWRGD output
for modules with an active low enable input, and the
LT1640AH has a PWRGD output for modules with an
active high enable input.
R2 •R3 +R1•R3 +R1•R2
R1
R3
V
UV,HL = V
– VGATE
•
UVL
R2 •R3
where VUVL is typically 1.223V.
The new hysteresis value will be:
When the DRAIN voltage of the LT1640AH is high with
respect to VEE (Figure 11), the internal transistor Q3 is
turned off and R7 and Q2 clamp the PWRGD pin one diode
drop (≈0.7V) above the DRAIN pin. Transistor Q2 sinks
the module’s pull-up current and the module turns off.
R2 •R3 +R1•R3 +R1•R2
R1
R3
V
= V
+ VGATE
•
HYS
UVHY
R2 •R3
WithR1=562k,R2=16.9kandR3=1.62M,VGATE =13.5V
andVUVHY =20mV, theundervoltagethresholdwillbe43V
(from low to high) and 37.6V (from high to low). The
hysteresis is 5.4V. A separate resistor divider should be
used to set the overvoltage threshold given by:
WhentheDRAINvoltagedropsbelowVPG, Q3willturnon,
shorting the bottom of R7 to DRAIN and turning Q2 off.
The pull-up current in the module then flows through R7,
pulling the PWRGD pin high and enabling the module.
ACTIVE HIGH
(SHORT PIN)
GND
ENABLE MODULE
+
+
OUT
GND
V
IN
V
8
LT1640AH
V
DD
PWRGD
Q2
1
7
R4
R7
6.5k
+
ON/OFF
3
2
UV
C3
+
–
+
R5
R6
Q3
EE
V
PG
–
OV
–
–
OUT
V
IN
V
V
DRAIN
V
EE
SENSE
5
GATE
6
4
*
R3
C2
C1
R2
3
4
R1
1640A F11
–48V
1
2
Q1
* DIODES INC. SMAT70A
Figure 11. Active High Enable Module
12
LT1640AL/LT1640AH
W U U
APPLICATIO S I FOR ATIO
U
When the DRAIN voltage of the LT1640AL is high with
respect to VEE, the internal pull-down transistor Q2 is off
and the PWRGD pin is in a high impedance state (Fig-
ure 12).ThePWRGDpinwillbepulledhighbythemodule’s
internal pull-up current source, turning the module off.
When the DRAIN voltage drops below VPG, Q2 will turn on
and the PWRGD pin will pull low, enabling the module.
than 6V. The gate voltage will be no greater than 18V for
supply voltages up to 80V.
Drain Pin Protection
A unique feature of the LT1640A is the ruggedness of the
DRAIN pin. The DRAIN is designed to withstand negative
voltages (with respect to VEE) without requiring an exter-
nal diode. A short circuit on the –48V backplane pulls up
the VEE pin, but due to the storage capacitor C3 (Fig-
ure 12), the DRAIN pin is held more negative than the VEE
pin. The body diode of Q1, plus the I • R drop across R1 (if
R1 is small), holds the DRAIN pin to less than 1.5V below
VEE. A 1.5V reverse voltage gives rise to a 50mA reverse
drain current, which is within the design capability of the
LT1640A. A design with R1 larger than 0.1Ω may require
a resistor in series with the DRAIN pin to not exceed the
50mA drain current maximum.
The PWRGD signal can also be used to turn on an LED or
optoisolator to indicate that the power is good as shown
in Figure 13.
Gate Pin Voltage Regulation
When the supply voltage to the chip is more than 15.5V,
theGATEpinvoltageisregulatedat13.5VaboveVEE. Ifthe
supply voltage is less than 15.5V, the GATE voltage will be
about 2V below the supply voltage. At the minimum 10V
supplyvoltage,thegatevoltageisguaranteedtobegreater
ACTIVE LOW
(SHORT PIN)
GND
ENABLE MODULE
+
+
GND
V
V
OUT
IN
8
V
LT1640AL
R4
DD
PWRGD
Q2
1
7
+
ON/OFF
–
3
+
–
UV
OV
C3
+
V
PG
R5
R6
–
V
EE
2
–
V
V
OUT
IN
DRAIN
V
4
SENSE GATE
EE
5
6
*
R3
C2
C1
R2
3
4
R1
1640A F12
–48V
1
2
Q1
* DIODES INC. SMAT70A
Figure 12. Active Low Enable Module
13
LT1640AL/LT1640AH
W U U
U
APPLICATIO S I FOR ATIO
(SHORT PIN)
GND
GND
R7
51k
5%
PWRGD
8
R4
562k
+
C3
100µF
100V
V
DD
1%
3
UV
R5
9.09k
1%
4N25
1
LT1640AL
PWRGD
2
OV
R6
10k
1%
V
SENSE
5
GATE
6
DRAIN
7
EE
4
R2
10Ω
5%
C1
150nF
25V
*
R3
18k
5%
C2
3.3nF
100V
R1
0.02Ω
5%
3
4
–48V
* DIODES INC. SMAT70A
1640A F13
1
2
Q1
IRF530
Figure 13. Using PWRGD to Drive an Optoisolator
U
PACKAGE DESCRIPTIO
Dimensions in inches (millimeters) unless otherwise noted.
N8 Package
8-Lead PDIP (Narrow 0.300)
(LTC DWG # 05-08-1510)
0.400*
(10.160)
MAX
8
7
6
5
4
0.255 ± 0.015*
(6.477 ± 0.381)
1
2
3
0.130 ± 0.005
0.300 – 0.325
0.045 – 0.065
(3.302 ± 0.127)
(1.143 – 1.651)
(7.620 – 8.255)
0.065
(1.651)
TYP
0.009 – 0.015
(0.229 – 0.381)
0.125
0.020
(0.508)
MIN
(3.175)
MIN
+0.035
0.325
–0.015
0.018 ± 0.003
(0.457 ± 0.076)
0.100
(2.54)
BSC
+0.889
8.255
(
)
N8 1098
–0.381
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
14
LT1640AL/LT1640AH
U
PACKAGE DESCRIPTIO
Dimensions in inches (millimeters) unless otherwise noted.
S8 Package
8-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
0.189 – 0.197*
(4.801 – 5.004)
7
5
8
6
0.150 – 0.157**
(3.810 – 3.988)
0.228 – 0.244
(5.791 – 6.197)
1
3
4
2
0.010 – 0.020
(0.254 – 0.508)
× 45°
0.053 – 0.069
(1.346 – 1.752)
0.004 – 0.010
(0.101 – 0.254)
0.008 – 0.010
(0.203 – 0.254)
0°– 8° TYP
0.016 – 0.050
(0.406 – 1.270)
0.050
(1.270)
BSC
0.014 – 0.019
(0.355 – 0.483)
TYP
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
SO8 1298
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tationthattheinterconnectionofitscircuitsasdescribedhereinwillnotinfringeonexistingpatentrights.
15
LT1640AL/LT1640AH
U
TYPICAL APPLICATION
Using an EMI Filter Module
using the Lucent FLTR100V10 filter module is shown in
Figure 14. When using a filter, an optoisolator is required
to prevent common mode transients from destroying the
PWRGD and ON/OFF pins.
Many applications place an EMI filter module in the power
path to prevent switching noise of the module from being
injected back onto the power supply. A typical application
R7
51k
5%
(SHORT PIN)
GND
4N25
LUCENT
JW050A1-E
GND
1
2
9
8
7
8
1
+
+
+
R4
562k
1%
5V
V
V
IN
OUT
SENSE
PWRGD
V
DD
+
C7
7
6
3
2
+
+
V
V
ON/OFF
TRIM
100µF
16V
UV
DRAIN
IN
OUT
C2
3.3nF
100V
R5
9.09k
1%
C3
0.1µF
100V
C4
0.1µF
100V
C5
100µF
100V
C6
0.1µF
100V
+
6
5
LT1640AL
LUCENT
FLTR100V10
–
SENSE
R3
18k
5%
OV
V
GATE
SENSE
5
4
–
–
–
–
V
V
V
V
R6
10k
1%
IN
OUT
CASE
IN
OUT
EE
CASE
R2
10Ω
5%
C1
150nF
25V
4
3
R1
0.02Ω
5%
1640A F14
*
3
4
–48V
* DIODES INC. SMAT70A
1
2
Q1
IRF530
Figure 14. Typical Application Using a Filter Module
RELATED PARTS
PART NUMBER
LTC®1421
LTC1422
LT1641
DESCRIPTION
COMMENTS
Operates from 3V to 12V
Dual Channel, Hot Swap Controller
Hot Swap Controller in SO-8
System Reset Output with Programmable Delay, 3V to 12V
Foldback Analog Current Limit
Positive 48V Hot Swap Controller in SO-8
Fault Protected Hot Swap Controller
PCI Hot Swap Controller
LTC1642
LTC1643
LTC1645
LTC1646
LTC1647
Operates Up to 16.5V, Protected to 33V
3.3V, 5V, 12V, –12V Supplies for PCI Bus
Operates from 1.2V to 12V, Power Sequencing
3.3V, 5V Supplies, 1V Precharge, Local PCI Reset Logic
Dual ON Pins for Supplies from 3V to 15V
Dual Hot Swap Controller
CompactPCITM Hot Swap Controller
Dual Hot Swap Controller
CompactPCI is a trademark of the PCI Industrial Computer Manufacturers Group
1640alahf LT/TP 0501 4K • PRINTED IN USA
LINEAR TECHNOLOGY CORPORATION 2001
LinearTechnology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
16
●
●
(408)432-1900 FAX:(408)434-0507 www.linear-tech.com
相关型号:
LT1640AHIS8#TR
LT1640A - Negative Voltage Hot Swap Controller; Package: SO; Pins: 8; Temperature Range: -40°C to 85°C
Linear
LT1640AHIS8#TRPBF
LT1640A - Negative Voltage Hot Swap Controller; Package: SO; Pins: 8; Temperature Range: -40°C to 85°C
Linear
LT1640ALCN8#PBF
LT1640A - Negative Voltage Hot Swap Controller; Package: PDIP; Pins: 8; Temperature Range: 0°C to 70°C
Linear
LT1640ALCS8#PBF
LT1640A - Negative Voltage Hot Swap Controller; Package: SO; Pins: 8; Temperature Range: 0°C to 70°C
Linear
LT1640ALCS8#TR
LT1640A - Negative Voltage Hot Swap Controller; Package: SO; Pins: 8; Temperature Range: 0°C to 70°C
Linear
©2020 ICPDF网 联系我们和版权申明