LT1211IS8#TRPBF [Linear]
暂无描述;型号: | LT1211IS8#TRPBF |
厂家: | Linear |
描述: | 暂无描述 运算放大器 |
文件: | 总20页 (文件大小:339K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LT1211/ LT1212
14MHz, 7V/ µs, Sing le Sup p ly
Dua l a nd Qua d
Pre c isio n Op Am p s
U
DESCRIPTIO
EATURE
S
F
TheLT®1211is adual,singlesupplyprecisionopampwith
a 14MHz gain-bandwidth product and a 7V/µs slew rate.
The LT1212 is a quad version of the same amplifier. The
DC precision of the LT1211/LT1212 eliminates trims in
most systems while providing high frequency perfor-
mance not usually found in single supply amplifiers.
■
■
■
Slew Rate: 7V/µs Typ
Gain-Bandwidth Product: 14MHz Typ
Fast Settling to 0.01%
2V Step to 200µV: 900ns Typ
10V Step to 1mV: 2.2µs Typ
Excellent DC Precision in All Packages
Input Offset Voltage: 275µV Max
Input Offset Voltage Drift: 6µV/°C Max
Input Offset Current: 30nA Max
■
The LT1211/LT1212 will operate on any supply greater
than 2.5V and less than 36V total. These amplifiers are
specified on single 3.3V, single 5V and±15V supplies, and
only require 1.3mA of quiescent supply current per ampli-
fier. The inputs can be driven beyond the supplies without
damage or phase reversal of the output. The minimum
output drive is 20mA, ideal for driving low impedance
loads.
Input Bias Current: 125nA Max
Open-Loop Gain: 1200V/mV Min
Single Supply Operation
■
Input Voltage Range Includes Ground
Output Swings to Ground While Sinking Current
Low Input Noise Voltage: 12nV/√Hz Typ
Low Input Noise Current: 0.2pA/√Hz Typ
Specified on 3.3V, 5V and ±15V
Large Output Drive Current: 20mA Min
Low Supply Current per Amplifier: 1.8mA Max
Dual in 8-Pin DIP and SO-8
■
■
■
■
■
■
■
O U
PPLICATI
A
S
■
■
■
■
■
■
2.5V Full-Scale 12-Bit Systems: VOS ≤ 0.45LSB
10V Full-Scale 16-Bit Systems: VOS ≤ 1.8LSB
Active Filters
Photo Diode Amplifiers
DAC Current-to-Voltage Amplifiers
Battery-Powered Systems
Quad in 14-Pin DIP and Narrow SO-16
Note: Forapplications requiringhigherslewrate,seetheLT1213/LT1214and
LT1215/LT1216 data sheets.
, LTC and LT are registered trademarks of Linear Technology Corporation.
U
O
TYPICAL APPLICATI
Input Bias Current Cancellation
Input Current vs Input Voltage
R
G
R
F
100
V = 5V, V
OUT
LINEAR REGION
IN
S
+
90
80
70
60
50
40
30
20
10
0
V
WITHOUT CANCELLATION
–
1/2
LT1211
R
= 300M
V
IN
OUT
V
IN
+
SIGNAL AMP
WITH CANCELLATION
1M
+
1/2
LT1211
CANCELLATION
AMP
R = 2.4G
IN
22pF
–
0.01
0.1
1
10
1211/12 TA01
INPUT VOLTAGE (V)
1M
1211/12 TA02
1
LT1211/ LT1212
W W W
U
ABSOLUTE AXI U RATI GS
Total Supply Voltage (V+ to V–) ............................. 36V
Input Current ..................................................... ±15mA
Output Short-Circuit Duration (Note 1)........ Continuous
Operating Temperature Range
Specified Temperature Range
LT1211C/LT1212C/
LT1211I/LT1212I (Note 5)................... –40°C to 85°C
LT1211M ......................................... –55°C to 125°C
Storage Temperature Range ................ –65°C to 150°C
Junction Temperature (Note 2)
Plastic Package (N8, S8, N, S) ........................ 150°C
Ceramic Package (J8)...................................... 175°C
Lead Temperature (Soldering, 10 sec)................. 300°C
LT1211C/LT1212C ............................ –40°C to 85°C
LT1211I/LT1212I............................... –40°C to 85°C
LT1211M ......................................... –55°C to 125°C
W U
/O
PACKAGE RDER I FOR ATIO
TOP VIEW
ORDER PART
ORDER PART
NUMBER
TOP VIEW
+
OUT A
–IN A
+IN A
1
2
3
4
NUMBER
8
7
6
5
V
+
OUT A
–IN A
+IN A
1
2
3
4
8
7
6
5
V
OUT B
–IN B
+IN B
OUT B
–IN B
+IN B
A
LT1211CN8
LT1211ACN8
LT1211IN8
LT1211MJ8
LT1211AMJ8
LT1211CS8
LT1211IS8
A
B
–
B
V
–
V
S8 PART MARKING
J8 PACKAGE
8-LEAD CERDIP
N8 PACKAGE
8-LEAD PDIP
S8 PACKAGE
8-LEAD PLASTIC SO
1211
1211I
T
T
JMAX = 175°C, θJA = 100°C/W (J)
JMAX = 150°C, θJA = 100°C/W (N)
T
JMAX = 150°C, θJA = 150°C/W
TOP VIEW
ORDER PART
NUMBER
ORDER PART
NUMBER
TOP VIEW
OUT A
–IN A
+IN A
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
OUT D
–IN D
+IN D
OUT A
–IN A
+IN A
1
2
3
4
5
6
7
14 OUT D
13 –IN D
A
D
C
LT1212CN
LT1212IN
LT1212CS
LT1212IS
A
B
D
+
–
12 +IN D
–
V
V
+
V
11
V
+IN B
–IN B
OUT B
NC
+IN C
–IN C
OUT C
NC
B
+IN B
–IN B
OUT B
10 +IN C
C
9
8
–IN C
OUT C
N PACKAGE
14-LEAD PDIP
S PACKAGE
16-LEAD PLASTIC SO
TJMAX = 150°C, θJA = 100°C/W
TJMAX = 150°C, θJA = 70°C/W
U
AVAILABLE OPTIO S
PACKAGE
NUMBER OF
OP AMPS
MAX TC V
CERAMIC
(J)
PLASTIC DIP
(N)
SURFACE MOUNT
(S)
OS
T RANGE
A
MAX V (25°C)
(∆V /∆T)
OS
OS
Two (Dual)
–40°C to 85°C
150µV
275µV
1.5µV/°C
3µV/°C
LT1211ACN8
LT1211CN8,
LT1211IN8
275µV
6µV/°C
LT1211CS8,
LT1211IS8
2
LT1211/ LT1212
U
AVAILABLE OPTIO S
PACKAGE
NUMBER OF
OP AMPS
MAX TC V
CERAMIC
(J)
PLASTIC DIP
(N)
SURFACE MOUNT
(S)
OS
T RANGE
A
MAX V (25°C)
(∆V /∆T)
OS
OS
Two (Dual)
–55°C to 125°C
150µV
275µV
275µV
1.5µV/°C
3µV/°C
6µV/°C
LT1211AMJ8
LT1211MJ8
Four (Quad)
–40°C to 85°C
LT1212CN,
LT1212IN
LT1212CS,
LT1212IS
5V ELECTRICAL CHARACTERISTICS
V = 5V, VCM = 0.5V, VOUT = 0.5V, TA = 25°C, unless otherwise noted.
S
LT1211AC
LT1211AM
LT1211C/LT1211M
LT1212C
TYP
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
MIN
MAX
UNITS
µV
V
OS
Input Offset Voltage
75
150
100
0.6
275
∆V
∆Time
Long-Term Input Offset
Voltage Stability
0.5
µV/Mo
OS
I
Input Offset Current
Input Bias Current
5
20
5
30
nA
nA
OS
I
B
50
100
60
125
Input Noise Voltage
Input Noise Voltage Density
0.1Hz to 10Hz
250
250
nV
P-P
e
n
f = 10Hz
12.5
12.0
12.5
12.0
nV/√Hz
nV/√Hz
O
f = 1000Hz
O
i
n
Input Noise Current Density
Input Resistance (Note 3)
f = 10Hz
f = 1000Hz
O
0.9
0.2
0.9
0.2
pA/√Hz
pA/√Hz
O
Differential Mode
Common Mode
10
40
500
10
40
500
MΩ
MΩ
Input Capacitance
f = 1MHz
10
10
pF
Input Voltage Range
3.5
0
3.8
–0.3
3.5
0
3.8
–0.3
V
V
CMRR
PSRR
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Large-Signal Voltage Gain
V
= 0V to 3.5V
90
90
105
115
560
86
87
102
110
560
dB
dB
CM
V = 2.5V to 12.5V
S
A
VOL
V = 0.05V to 3.7V, R = 500Ω
O
250
250
V/mV
L
Maximum Output Voltage Swing Output High, No Load
4.30
4.20
3.85
4.40
4.30
4.00
4.30
4.20
3.85
4.40
4.30
4.00
V
V
V
(Note 4)
Output High, I
Output High, I
= 1mA
SOURCE
SOURCE
= 15mA
Output Low, No Load
0.003 0.006
0.047 0.065
0.362 0.500
0.003 0.006
0.047 0.065
0.362 0.500
V
V
V
Output Low, I
Output Low, I
= 1mA
= 15mA
SINK
SINK
I
Maximum Output Current
Slew Rate
(Note 9)
±20
±50
4
±20
±50
4
mA
V/µs
MHz
mA
V
O
SR
A = –2
V
GBW
Gain-Bandwidth Product
Supply Current per Amplifier
Minimum Supply Voltage
Full Power Bandwidth
Rise Time, Fall Time
Overshoot
f = 100kHz
13
13
I
S
0.9
1.3
2.2
300
45
1.8
2.5
0.9
1.3
2.2
300
45
1.8
2.5
Single Supply
A = 1, V = 2.5V
P-P
kHz
ns
V
O
t , t
r
A = 1, 10% to 90%, V = 100mV
V O
f
OS
A = 1, V = 100mV
V
25
25
%
O
t
t
Propagation Delay
A = 1, V = 100mV
36
36
ns
PD
S
V
O
Settling Time
0.01%, A = 1, ∆V = 2V
900
75
900
75
ns
V
O
Open-Loop Output Resistance
Total Harmonic Distortion
I = 0mA, f = 5MHz
O
Ω
THD
A = 1, V = 1V , 20Hz to 20kHz
0.001
0.001
%
V
O
RMS
3
LT1211/ LT1212
5V ELECTRICAL CHARACTERISTICS
V = 5V, VCM = 0.5V, VOUT = 0.5V, 0°C ≤ TA ≤ 70°C, unless otherwise noted.
S
LT1211AC
TYP
LT1211C/LT1212C
SYMBOL PARAMETER
CONDITIONS
MIN
MAX
175
1.5
MIN
TYP
MAX
UNITS
V
OS
Input Offset Voltage
100
0.7
150
375
µV
∆V
∆T
Input Offset Voltage Drift
(Note 3)
8-Pin DIP Package
14-Pin DIP, SOIC Package
1
2
3
6
µV/°C
µV/°C
OS
I
Input Offset Current
Input Bias Current
Input Voltage Range
5
25
10
70
35
nA
nA
OS
I
B
60
110
135
3.4
0.1
3.5
–0.1
3.4
0.1
3.5
–0.1
V
V
CMRR
PSRR
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Large-Signal Voltage Gain
V
= 0.1V to 3.4V
89
89
105
114
430
85
86
102
110
430
dB
dB
CM
V = 2.5V to 12.5V
S
A
VOL
V = 0.05V to 3.7V, R = 500Ω
O
150
150
V/mV
L
Maximum Output Voltage Swing Output High, No Load
4.20
4.10
3.90
4.33
4.23
4.03
4.20
4.10
3.90
4.33
4.23
4.03
V
V
V
(Note 4)
Output High, I
Output High, I
= 1mA
SOURCE
SOURCE
= 10mA
Output Low, No Load
0.004 0.007
0.052 0.070
0.290 0.400
0.004 0.007
0.052 0.070
0.290 0.400
V
V
V
Output Low, I
Output Low, I
= 1mA
= 10mA
SINK
SINK
I
S
Supply Current per Amplifier
0.8
1.4
2.1
0.8
1.4
2.1
mA
V = 5V, VCM = 0.5V, VOUT = 0.5V, –40°C ≤ TA ≤ 85°C, unless otherwise noted. (Note 5)
S
LT1211C/LT1212C
LT1211I/LT1212I
LT1211AC
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
120
0.7
MAX
200
1.5
MIN
TYP
MAX
UNITS
V
OS
Input Offset Voltage
175
500
µV
∆V
∆T
Input Offset Voltage Drift
(Note 3)
8-Pin DIP Package
14-Pin DIP, SOIC Package
1
2
3
6
µV/°C
µV/°C
OS
I
Input Offset Current
Input Bias Current
Input Voltage Range
10
70
30
20
80
50
nA
nA
OS
I
B
120
145
3.1
0.2
3.2
0
3.1
0.2
3.2
0
V
V
CMRR
PSRR
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Large-Signal Voltage Gain
V
= 0.2V to 3.1V
88
88
104
113
390
84
85
101
109
390
dB
dB
CM
V = 2.5V to 12.5V
S
A
VOL
V = 0.05V to 3.7V, R = 500Ω
O
100
100
V/mV
L
Maximum Output Voltage Swing Output High, No Load
4.15
4.00
3.80
4.25
4.16
3.96
4.15
4.00
3.80
4.25
4.16
3.96
V
V
V
(Note 4)
Output High, I
Output High, I
= 1mA
SOURCE
SOURCE
= 10mA
Output Low, No Load
0.005 0.008
0.053 0.075
0.300 0.420
0.005 0.008
0.053 0.075
0.300 0.420
V
V
V
Output Low, I
Output Low, I
= 1mA
= 10mA
SINK
SINK
I
S
Supply Current per Amplifier
0.7
1.5
2.2
0.7
1.5
2.2
mA
4
LT1211/ LT1212
5V ELECTRICAL CHARACTERISTICS
V = 5V, VCM = 0.5V, VOUT = 0.5V, –55°C ≤ TA ≤ 125°C, unless otherwise noted.
S
LT1211AM
TYP
LT1211M
SYMBOL PARAMETER
CONDITIONS
MIN
MAX
250
1.5
MIN
TYP
200
1
MAX
500
3
UNITS
µV
V
OS
Input Offset Voltage
140
0.7
∆V
∆T
Input Offset Voltage Drift
(Note 3)
µV/°C
OS
I
Input Offset Current
Input Bias Current
Input Voltage Range
15
75
40
25
85
75
nA
nA
OS
I
B
130
160
3.1
0.4
3.2
0.2
3.1
0.4
3.2
0.2
V
V
CMRR
PSRR
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Large-Signal Voltage Gain
V
= 0.4V to 3.1V
87
87
104
113
250
81
84
101
109
250
dB
dB
CM
V = 2.5V to 12.5V
S
A
VOL
V = 0.05V to 3.7V, R = 500Ω
O
100
100
V/mV
L
Maximum Output Voltage Swing Output High, No Load
4.10
3.95
3.70
4.20
4.10
3.90
4.10
3.95
3.70
4.20
4.10
3.90
V
V
V
(Note 4)
Output High, I
Output High, I
= 1mA
SOURCE
SOURCE
= 10mA
Output Low, No Load
0.007 0.010
0.060 0.085
0.350 0.500
0.007 0.010
0.060 0.085
0.350 0.500
mV
mV
mV
Output Low, I
Output Low, I
= 1mA
= 10mA
SINK
SINK
I
S
Supply Current per Amplifier
0.5
1.7
2.5
0.5
1.7
2.5
mA
+
S
ELECTRICAL CHARACTERISTICS
15V
–
V = ±15V, VCM = 0V, VOUT = 0V, TA = 25°C, unless otherwise noted.
LT1211AC
LT1211AM
TYP
LT1211C/LT1211M
LT1212C
SYMBOL PARAMETER
CONDITIONS
MIN
MAX
400
20
MIN
TYP
150
5
MAX
550
30
UNITS
µV
V
Input Offset Voltage
Input Offset Current
Input Bias Current
Input Voltage Range
125
5
OS
I
OS
nA
I
B
45
95
50
120
nA
13.5
13.8
–15.0 –15.3
13.5
13.8
V
V
–15.0 – 15.3
CMRR
PSRR
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Large-Signal Voltage Gain
V
= –15V to 13.5V
90
90
105
113
86
87
102
110
dB
dB
CM
V = ±2V to ±18V
S
A
VOL
V = 0V to ±10V, R = 2k
O
1200
13.8
5000
14.0
1200
13.8
5000
14.0
V/mV
V
L
Maximum Output Voltage Swing Output High, I
= 15mA
SOURCE
Output Low, I
(Note 9)
= 15mA
–14.4 –14.6
–14.4 –14.6
V
SINK
I
Maximum Output Current
Slew Rate
±20
5
±50
7
±20
5
±50
7
mA
V/µs
MHz
mA
dB
O
SR
A = –2 (Note 6)
V
GBW
Gain-Bandwidth Product
Supply Current per Amplifier
Channel Separation
Minimum Supply Voltage
Full Power Bandwidth
Settling Time
f = 100kHz
8
14
8
14
I
S
0.9
128
1.8
140
±1.2
60
2.5
0.9
128
1.8
140
±1.2
60
2.5
V = ±10V, R = 2k
O
L
Equal Split Supplies
A = 1, V = 20V
±2.0
±2.0
V
kHz
µs
V
O
P-P
0.01%, A = 1, ∆V = 10V
2.2
2.2
V
O
5
LT1211/ LT1212
+
S
15V
ELECTRICAL CHARACTERISTICS
–
V = ±15V, VCM = 0V, VOUT = 0V, 0°C ≤ TA ≤ 70°C, unless otherwise noted.
LT1211AC
TYP
LT1211C/LT1212C
SYMBOL PARAMETER
CONDITIONS
MIN
MAX
425
1.5
MIN
TYP
MAX
UNITS
V
OS
Input Offset Voltage
150
0.7
200
650
µV
∆V
∆T
Input Offset Voltage Drift
(Note 3)
8-Pin DIP Package
14-Pin DIP, SOIC Package
1
2
3
6
µV/°C
µV/°C
OS
I
Input Offset Current
Input Bias Current
Input Voltage Range
10
20
10
35
nA
nA
OS
I
B
55
100
60
125
13.4
13.5
–14.9 –15.1
13.4
13.5
–14.9 –15.1
V
V
CMRR
PSRR
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Large-Signal Voltage Gain
V
= –14.9V to 13.4V
89
89
104
112
85
86
101
108
dB
dB
CM
V = ±2V to ±18V
S
A
VOL
V = 0V to ±10V, R = 2k
O
1000
13.8
3500
14.0
1000
13.8
3500
14.0
V/mV
V
L
Maximum Output Voltage Swing Output High, I
= 10mA
SOURCE
Output Low, I
= 10mA
–14.5 –14.7
0.8 2.1
V = ±15V, VCM = 0V, VOUT = 0V, –40°C ≤ TA ≤ 85°C, unless otherwise noted. (Note 5)
–14.5 –14.7
0.8 2.1
V
SINK
I
Supply Current per Amplifier
2.9
2.9
mA
S
S
LT1211C/LT1212C
LT1211I/LT1212I
LT1211AC
TYP
SYMBOL PARAMETER
CONDITIONS
MIN
MAX
450
1.5
MIN
TYP
MAX
UNITS
V
OS
Input Offset Voltage
175
0.7
250
700
µV
∆V
∆T
Input Offset Voltage Drift
(Note 3)
8-Pin DIP Package
14-Pin DIP, SOIC Package
1
2
3
6
µV/°C
µV/°C
OS
I
Input Offset Current
Input Bias Current
Input Voltage Range
10
25
10
40
nA
nA
OS
I
B
55
100
60
130
13.1
13.2
–14.8 –15.0
13.1
13.2
–14.8 –15.0
V
V
CMRR
PSRR
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Large-Signal Voltage Gain
V
= –14.8V to 13.1V
88
88
103
111
84
85
100
107
dB
dB
CM
V = ±2V to ±18V
S
A
VOL
V = 0V to ±10V, R = 2k
O
1000
13.7
3000
13.9
1000
13.7
3000
13.9
V/mV
V
L
Maximum Output Voltage Swing Output High, I
= 10mA
SOURCE
Output Low, I
= 10mA
–14.5 –14.7
–14.5 –14.7
V
SINK
I
S
Supply Current per Amplifier
0.7
2.2
3.0
0.7
2.2
3.0
mA
V = ±15V, VCM = 0V, VOUT = 0V, –55°C ≤ TA ≤ 125°C, unless otherwise noted.
S
LT1211AM
TYP
LT1211M
TYP
SYMBOL PARAMETER
CONDITIONS
MIN
MAX
500
1.5
MIN
MAX
800
3
UNITS
µV
V
OS
Input Offset Voltage
200
0.7
300
1
∆V
∆T
Input Offset Voltage Drift
(Note 3)
µV/°C
OS
I
Input Offset Current
Input Bias Current
Input Voltage Range
10
40
10
60
nA
nA
OS
I
B
55
110
60
140
13.1
13.2
–14.6 –14.8
13.1
13.2
–14.6 –14.8
V
V
CMRR
PSRR
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Large-Signal Voltage Gain
V
= –14.6V to 13.1V
87
87
103
111
81
84
100
107
dB
dB
CM
V = ±2V to ±15V
S
A
VOL
V = 0V to ±10V, R = 2k
O
800
13.6
1500
13.8
800
13.6
1500
13.8
V/mV
V
L
Maximum Output Voltage Swing Output High, I
= 10mA
SOURCE
Output Low, I
= 10mA
–14.3 –14.5
0.5 2.3
–14.3 –14.5
0.5 2.3
V
SINK
I
S
Supply Current per Amplifier
3.4
3.4
mA
6
LT1211/ LT1212
3.3V ELECTRICAL CHARACTERISTICS
V = 3.3V, VCM = 0.5V, VOUT = 0.5V, TA = 25°C, unless otherwise noted. (Note 7)
S
LT1211AC
LT1211AM
TYP
LT1211C/LT1211M
LT1212C
SYMBOL PARAMETER
CONDITIONS
MIN
MAX
MIN
TYP
MAX
UNITS
V
OS
Input Offset Voltage
75
150
100
275
µV
Input Voltage Range (Note 8)
1.8
0
2.1
–0.3
1.8
0
2.1
– 0.3
V
V
Maximum Output Voltage Swing Output High, No Load
2.60
2.50
2.15
2.70
2.60
2.30
2.60
2.50
2.15
2.70
2.60
2.30
V
V
V
Output High, I
Output High, I
= 1mA
= 15mA
SOURCE
SOURCE
Output Low, No Load
0.003 0.006
0.047 0.065
0.362 0.500
0.003 0.006
0.047 0.065
0.362 0.500
V
V
V
Output Low, I
Output Low, I
= 1mA
= 15mA
SINK
SINK
I
O
Maximum Output Current
±20
±50
±20
±50
mA
V = 3.3V, VCM = 0.5V, VOUT = 0.5V, 0°C ≤ TA ≤ 70°C, unless otherwise noted. (Note 7)
S
LT1211AC
LT1211C/LT1212C
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
MIN
TYP
MAX
UNITS
V
OS
Input Offset Voltage
100
175
150
375
µV
Input Voltage Range (Note 8)
1.7
0.1
1.4
–0.1
1.7
0.1
1.8
–0.1
V
V
Maximum Output Voltage Swing Output High, No Load
2.50
2.40
2.20
2.63
2.53
2.33
2.50
2.40
2.20
2.63
2.53
2.33
V
V
V
Output High, I
Output High, I
= 1mA
= 10mA
SOURCE
SOURCE
Output Low, No Load
0.004 0.007
0.052 0.070
0.290 0.400
0.004 0.007
0.052 0.070
0.290 0.400
V
V
V
Output Low, I
Output Low, I
= 1mA
= 10mA
SINK
SINK
V = 3.3V, VCM = 0.5V, VOUT = 0.5V, –40°C ≤ TA ≤ 85°C, unless otherwise noted. (Notes 5, 7)
S
LT1211C/LT1212C
LT1211I/LT1212I
LT1211AC
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
MIN
TYP
MAX
UNITS
V
OS
Input Offset Voltage
120
200
175
500
µV
Input Voltage Range (Note 8)
1.4
0.2
1.5
0
1.4
0.2
1.5
0
V
V
Maximum Output Voltage Swing Output High, No Load
2.45
2.30
2.10
2.55
2.46
2.26
2.45
2.30
2.10
2.55
2.46
2.26
V
V
V
Output High, I
Output High, I
= 1mA
= 10mA
SOURCE
SOURCE
Output Low, No Load
0.005 0.008
0.053 0.075
0.300 0.420
0.005 0.008
0.053 0.075
0.300 0.420
V
V
V
Output Low, I
Output Low, I
= 1mA
= 10mA
SINK
SINK
V = 3.3V, VCM = 0.5V, VOUT = 0.5V, –55°C ≤ TA ≤ 125°C, unless otherwise noted. (Note 7)
S
LT1211AM
LT1211M
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
MIN
TYP
MAX
UNITS
V
OS
Input Offset Voltage
130
250
200
500
µV
Input Voltage Range (Note 8)
1.4
0.4
1.5
0.2
1.4
0.4
1.5
0.2
V
V
Maximum Output Voltage Swing Output High, No Load
2.40
2.25
2.00
2.50
2.40
2.20
2.40
2.25
2.00
2.50
2.40
2.20
V
V
V
Output High, I
Output High, I
= 1mA
= 10mA
SOURCE
SOURCE
Output Low, No Load
0.007 0.010
0.060 0.085
0.350 0.500
0.007 0.010
0.060 0.085
0.350 0.500
V
V
V
Output Low, I
Output Low, I
= 1mA
= 10mA
SINK
SINK
7
LT1211/ LT1212
ELECTRICAL CHARACTERISTICS
Note 5: The LT1211C/LT1212C are guaranteed to meet specified
performance from 0°C to 70°C and are designed, characterized and
expected to meet these extended temperature limits, but are not tested at
–40°C and 85°C. The LT1211I/LT1212I are guaranteed to meet the
extended temperature limits.
Note 1: A heat sink may be required to keep the junction temperature
below absolute maximum when the output is shorted indefinitely.
Note 2: T is calculated from the ambient temperature T and power
J
A
dissipation P according to the following formulas:
D
LT1211MJ8, LT1211AMJ8: T = T + (P ×100°C/W)
J
A
D
Note 6: Slew rate is measured between ±8.5V on an output swing of ±10V
on ±15V supplies.
LT1211CN8, LT1211ACN8: T = T + (P ×100°C/W)
J
A
D
LT1211CS8:
LT1212CN:
LT1212CS:
T = T + (P ×150°C/W)
J A D
Note 7: Most LT1211/LT1212 electrical characteristics change very little
with supply voltage. See the 5V tables for characteristics not listed in the
3.3V table.
T = T + (P ×70°C/W)
J
A
D
T = T + (P ×100°C/W)
J
A
D
Note 3: This parameter is not 100% tested.
Note 8: Guaranteed by correlation to 5V and ±15V tests.
Note 9: Guaranteed by correlation to 3.3V tests.
Note 4: Guaranteed by correlation to 3.3V and ±15V tests.
U W
TYPICALPERFOR A CE CHARACTERISTICS
Distribution of Offset Voltage Drift
with Temperature
Distribution of Input Offset Voltage
Distribution of Input Offset Voltage
70
60
50
40
30
20
10
0
70
60
50
40
30
20
10
0
50
40
30
20
10
0
LT1211 J8 PACKAGE
LT1211 N8 PACKAGE
V = 5V
S
LT1211 J8 PACKAGE
LT1211 N8 PACKAGE
V = 5V
S
LT1211 J8 PACKAGE
LT1211 N8 PACKAGE
V = ±15V
S
–350
–150 –50 50
150 250 350
–700
–300 –100 100 300 500 700
–250
–1
–500
–3
–2
1
0
2
3
INPUT OFFSET VOLTAGE (µV)
INPUT OFFSET VOLTAGE (µV)
OFFSET VOLTAGE DRIFT WITH TEMPERATURE (µV/°C)
1211/12 G01
1211/12 G03
1211/12 G02
Distribution of Offset Voltage Drift
with Temperature
Distribution of Input Offset Voltage
Distribution of Input Offset Voltage
70
60
50
40
30
20
10
0
70
60
50
40
30
20
10
0
50
V = 5V
S
LT1211 S8 PACKAGE
LT1212 N PACKAGE
LT1212 S PACKAGE
V = 5V
S
LT1211 S8 PACKAGE
LT1212 N PACKAGE
LT1212 S PACKAGE
V = ±15V
S
LT1211 S8 PACKAGE
LT1212 N PACKAGE
LT1212 S PACKAGE
40
30
20
10
0
–2
2
–6
–4
–350
–150 –50 50
150 250 350
0
4
6
–700
–300 –100 100 300 500 700
–250
–500
INPUT OFFSET VOLTAGE (µV)
INPUT OFFSET VOLTAGE (µV)
OFFSET VOLTAGE DRIFT WITH TEMPERATURE (µV/°C)
1211/12 G04
1211/12 G06
1211/12 G05
8
LT1211/ LT1212
U W
TYPICALPERFOR A CE CHARACTERISTICS
Voltage Gain, Phase vs
Frequency
Gain-Bandwidth Product,
Phase Margin vs Supply Voltage
Voltage Gain vs Frequency
100
80
60
40
20
0
16
15
14
13
12
11
10
140
120
100
80
C = 20pF
C = 20pF
L
L
PHASE
R
L
= 2k
R = 2k
L
T
A
= –55°C
T
A
= 25°C
60
40
T
A
= 125°C
V = ±15V
V = 5V
S
S
20
60
60
50
40
30
20
10
0
GAIN
T
A
= 25°C, 125°C
0
40
V = ±15V
S
T
A
= –55°C
–20
–40
–60
20
V = ±15V
S
0
V = 5V
S
V = 5V
S
–20
–20
100k
1M
10M
100M
1k 10k 100k
10M
100M
1
3
7
10
40
1
10 100
1M
5
20 30
TOTAL SUPPLY VOLTAGE (V)
FREQUENCY (Hz)
FREQUENCY (Hz)
1211/12 G08
1211/12 G07
1211/12 G09
Slew Rate vs Temperature
Slew Rate vs Supply Voltage
Capacitive Load Handling
10
8
10
80
T = 25°C
A = –2
V
R = 10k
L
V = 5V
S
A
A = –2
T = 125°C
A
70
60
50
40
30
20
10
0
V
R = 10k
L
8
6
4
2
0
V = ±15V
S
T = 25°C
A
6
T = –55°C
A
V = 5V
S
A = 1
V
4
A = 5
V
A = 10
V
2
–50
25
0
50
75 100 125
–25
10
100
1000
10000
0
4
8
12 16 20 24 28 32 36
TEMPERATURE (°C)
CAPACITIVE LOAD (pF)
TOTAL SUPPLY VOLTAGE (V)
1211/12 G10
1211/12 G11
1211/12 G12
Undistorted Output Swing
vs Frequency, V = 5V
Undistorted Output Swing
vs Frequency, V = ±15V
Total Harmonic Distortion and
Noise vs Frequency
S
S
0.1
5
4
3
2
1
0
30
V = 5V
S
V = 5V
S
V = ±15V
S
A = –1
V
V = 3V
O
R
L
P-P
25
20
15
10
5
= 1k
A = 1
V
0.01
A = 10
V
0.001
A = 1
V
0.0001
0
100
100
1k
10k
FREQUENCY (Hz)
100k
1M
1k
10k
100k
1M
10
100
1k
FREQUENCY (Hz)
10k
100k
FREQUENCY (Hz)
1211/12 G13
1211/12 G14
1211/12 G15
9
LT1211/ LT1212
U W
TYPICALPERFOR A CE CHARACTERISTICS
Open-Loop Voltage Gain
vs Supply Voltage
Positive Output Saturation
Voltage vs Temperature
Open-Loop Gain, V = 5V
S
6k
5k
4k
3k
2k
1k
0
1.4
1.2
1.0
0.8
0.6
0.4
0.2
V = 5V
R
L
= 2k
S
RL = 2k
I
= 20mA
SOURCE
T
= –55°C
= 25°C
A
I
= 10mA
SOURCE
RL =
500Ω
T
A
I
= 1mA
SOURCE
T
A
= 125°C
I
= 10µA
SOURCE
0
1
2
3
4
OUTPUT (V)
1211/12 G17
50
100 125
–50 –25
0
25
75
0
4
8
12 16 20 24 28 32 36
TOTAL SUPPLY VOLTAGE (V)
TEMPERATURE (°C)
1211/12 G16
1211/12 G18
Negative Output Saturation
Voltage vs Temperature
Voltage Gain vs Load Resistance
Open-Loop Gain, V = ±15V
S
1000
100
10
10k
1k
I
= 20mA
T
A
= 25°C
SINK
RL = 2k
I
= 10mA
SINK
V = ±15V
S
V = 5V
S
I
= 1mA
SINK
RL =
500Ω
100
10
I
= 10µA
SINK
–10
0
10
OUTPUT (V)
V = 5V
1211/12 G20
S
1
–50 –25
0
25
50
75 100 125
10
100
1k
10k
TEMPERATURE (°C)
LOAD RESISTANCE (Ω)
1211/12 G21
1211/12 G19
Output Short-Circuit Current
vs Temperature
Channel Separation vs Frequency
Output Impedance vs Frequency
140
130
120
110
100
90
60
50
40
30
20
1000
100
10
V = ±15V
V = ±15V
S
T
A
S
= 25°C
V = 5V
S
SOURCING
V = ±15V
S
A = 100
V
SOURCING
OR SINKING
80
1
A = 10
V
70
60
0.1
50
A = 1
V
40
0.01
30
10k
100k
1M
10M
50
CASE TEMPERATURE (°C)
100 125
–50 –25
0
25
75
10k
100k
1M
10M
FREQUENCY (Hz)
FREQUENCY (Hz)
1211/12 G22
1211/12 G24
1211/12 G23
10
LT1211/ LT1212
U W
TYPICALPERFOR A CE CHARACTERISTICS
5V Large-Signal Response
5V Large-Signal Response
5V Small-Signal Response
3V
3V
0V
0V
100ns/DIV
500ns/DIV
500ns/DIV
V = 5V
V = 5V
AV = 1
V = 5V
AV = –1
S
S
S
A = 1
V
1211/12 G25
1211/12 G26
RF = RG = 1k
CF = 20pF
1211/12 G27
±15V Large-Signal Response
±15V Large-Signal Response
±15V Small-Signal Response
10V
0V
10V
0V
–10V
–10V
2µs/DIV
2µs/DIV
100ns/DIV
V = ±15V
S
V = ±15V
S
V = ±15V
A = 1
V
S
A = –1
RF = RG = 1k
A = 1
V
1211/12 G29
1211/12 G28
V
1211/12 G30
Settling Time to 0.01%
vs Output Step
±15V Settling
5V Settling
10
8
V = ±15V
S
NONINVERTING
6
INVERTING
4
2
0
–2
–4
–6
–8
–10
INVERTING
200ns/DIV
500ns/DIV
V = 5V
AV = 1
V = ±15V
AV = –1
S
S
NONINVERTING
1.0
1211/12 G31
1211/12 G32
0.5
2.0
2.5
1.5
SETTLING TIME (µs)
1211/12 G33
11
LT1211/ LT1212
U W
TYPICALPERFOR A CE CHARACTERISTICS
Supply Current vs Supply Voltage
Supply Current vs Temperature
Warm-Up Drift vs Time
2
1
0
2.6
2.2
1.8
1.4
1.0
0.6
2
1
V = 5V
S
T
= 125°C
A
R
= ∞
L
2 TYPICAL AMPLIFIERS
V = ±15V
S
T
= 25°C
A
0
V = 5V
S
T
A
= –55°C
–1
–2
25
TEMPERATURE (°C)
–50
0
50
75 100 125
–25
0
1
2
3
4
5
0
10
20
30
40
50
SUPPLY VOLTAGE (V)
TIME AFTER POWER-UP (SEC)
1211/12 G34
1211/12 G35
1211/12 G36
Input Bias Current vs
Common-Mode Voltage
Common-Mode Range
vs Temperature
Input Bias Current vs Temperature
+
100
90
80
70
60
50
40
30
0
V
V = 5V
S
V = 5V
S
–20
–40
+
V –1
T
A
= 25°C
T
= 125°C
= –55°C
+
A
V –2
–
V +1
–60
T
A
+I
B
–
I
–I
B
OS
V
–80
–
–100
V –1
–50 –25
0
25
50
75
100 125
–1
0
1
2
3
4
50
TEMPERATURE (°C)
100 125
–50 –25
0
25
75
TEMPERATURE (°C)
COMMON-MODE VOLTAGE (V)
1211/12 G38
1211/12 G37
1211/12 G39
Input Noise Current, Noise
Voltage Density vs Frequency
Common-Mode Rejection Ratio
vs Frequency
Input Referred Power Supply
Rejection Ratio vs Frequency
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
20
18
16
14
12
10
8
130
120
110
100
90
110
100
90
80
70
60
50
40
30
20
10
V = ±15V
V = ±15V
A = 100
V
S
V = 5V
S
S
T
R
= 25°C
= 0Ω
A
S
VOLTAGE NOISE
POSITIVE SUPPLY
80
70
6
60
4
50
NEGATIVE SUPPLY
CURRENT NOISE
10k
2
40
0
30
10
100
1k
100k
1k
10k
100k
FREQUENCY (Hz)
1M
10M
10k
100k
1M
10M
FREQUENCY (Hz)
FREQUENCY (Hz)
1211/12 G40
1211/12 G42
1211/12 G41
12
LT1211/ LT1212
O U
W
U
PPLICATI
S I FOR ATIO
A
Supply Voltage
For example, calculate the worst case power dissipation
whileoperatingon ±15Vsupplies anddrivinga500Ω load.
The LT1211/LT1212 op amps are fully functional and all
internal bias circuits are in regulation with 2.2V of supply.
The amplifiers will continue to function with as little as
1.5V, although the input common-mode range and the
phase margin are about gone. The minimum operating
supply voltage is guaranteed by the PSRR tests which are
done with the input common mode equal to 500mV and a
minimum supply voltage of 2.5V. The LT1211/LT1212 are
guaranteed over the full –55°C to 125°C range with a
minimum supply voltage of 2.5V.
ISMAX = 2.5 + 0.036 • (30 – 5) = 3.4mA
PDMAX = 2 • V • ISMAX + (V – VOMAX) • VOMAX/RL
S
S
PDMAX = 2 • 15V × 3.4mA + (15V – 7.5V) • 7.5V/500
= 0.102 + 0.113 = 0.215W per Amp
If this is the quad LT1212, the total power in the package
is four times that, or 0.860W. Now calculate how much the
die temperature will rise above the ambient. The total
power dissipation times the thermal resistance of the
package gives the amount of temperature rise. For this
example, in the SO surface mount package, the thermal
resistance is 100°C/W junction-to-ambient in still air.
The positive supply pin of the LT1211/LT1212 should be
bypassed with a small capacitor (about 0.01µF) within an
inch of the pin. When driving heavy loads and for good
settling time, an additional 4.7µF capacitor should be
used. When using split supplies, the same is true for the
negative supply pin.
Temperature Rise = PDMAX • θJA = 0.860W • 100°C/W
= 86°C
The maximum junction temperature allowed in the plastic
package is 150°C. Therefore the maximum ambient al-
lowed is the maximum junction temperature less the
temperature rise.
Power Dissipation
The LT1211/LT1212 amplifiers combine high speed and
large output current drive into very small packages. Be-
causetheseamplifiers workoveraverywidesupplyrange,
itis possibletoexceedthemaximumjunctiontemperature
under certain conditions. To insure that the LT1211/
LT1212 are used properly, calculate the worst case power
dissipation, define the maximum ambient temperature,
select the appropriate package and then calculate the
maximum junction temperature.
Maximum Ambient = 150°C – 86°C = 64°C
That means the SO quad can only be operated at or below
64°C on ±15V supplies with a 500Ω load.
As a guideline to help in the selection of the LT1211/
LT1212, the following table describes the maximum sup-
ply voltage that can be used with each part based on the
following assumptions:
The worst case amplifier power dissipation is the total of
the quiescent current times the total power supply voltage
plus the power in the IC due to the load. The quiescent
supply current of the LT1211/LT1212 has a positive tem-
perature coefficient. The maximum supply current of each
amplifier at 125°C is given by the following formula:
1. The maximum ambient is 70°C or 125°C depending
on the part rating.
2. The load is 500Ω, includes the feedback resistors.
3. The output can be anywhere between the supplies.
PART
MAX SUPPLIES
MAX POWER AT MAX T
A
I
SMAX = 2.5 + 0.036 • (V – 5) in mA
S
LT1211MJ8
LT1211CN8
LT1211CS8
LT1212CN
LT1212CS
19.5V or ±16.4V
25.2V or ±18.0V
20.3V or ±17.1V
21.0V or ±17.8V
17.3V or ±14.4V
500mW
800mW
533mW
1143mW
800mW
V is the total supply voltage.
S
The power in the IC due to the load is a function of the
outputvoltage,thesupplyvoltageandloadresistance.The
worst case occurs when the output voltage is at half
supply, if it can go that far, or its maximum value if it
cannot reach half supply.
13
LT1211/ LT1212
O U
W
U
PPLICATI
A
S I FOR ATIO
Inputs
positive rail, is about 100Ω as the output starts to source
current; this resistance drops to about 25Ω as the current
increases. Therefore when the output sources 1mA, the
output will swing to within 0.7V of the positive supply.
While sourcing 20mA, it is within 1.1V of the positive
supply.
Typically, at room temperature, the inputs of the LT1211/
LT1212 can common mode 400mV below ground (V–)
and to within 1.2V of the positive supply with the amplifier
still functional. However the input bias current and offset
voltage will shift as shown in the characteristic curves. For
full precision performance, the common-mode range
shouldbelimitedbetweenground(V–)and1.5Vbelowthe
positive supply.
When either of the inputs is taken below ground (V–) by
more than about 700mV, that input bias current will
increase dramatically. The current is limited by internal
100Ω resistors between the input pins and diodes to each
supply. The output will remain low (no phase reversal) for
inputs 1.3Vbelowground(V–).Iftheoutputdoes nothave
to sink current, such as in a single supply system with a 1k
load to ground, there is no phase reversal for inputs up to
8V below ground.
TheoutputoftheLT1211/LT1212willswingtowithin3mV
of the negative supply while sinking zero current. Thus, in
a typical single supply application with the load going to
ground, the output will go to within 3mV of ground. The
open-loop output resistance when the output is driven
hardintothenegativerailis about44Ωatlowcurrents and
reduces to about 24Ω at high currents. Therefore, when
the output sinks 1mA, the output is about 42mV above the
negative supply and while sinking 20mA, it is about
480mV above it.
The output of the LT1211/LT1212 has reverse-biased
diodes toeachsupply. Iftheoutputis forcedbeyondeither
supply, unlimited currents will flow. If the current is
transient and limited to several hundred mA, no damage
will occur.
There are no clamps across the inputs of the LT1211/
LT1212 and therefore each input can be forced to any
voltage between the supplies. The input current will re-
main constant at about 60nA over most of this range.
Whenaninputgets closerthan1.5Vtothepositivesupply,
that input current will gradually decrease to zero until the
inputgoes abovethesupply, thenitwillincreaseduetothe
previously mentioned diodes. If the inverting input is held
more positive than the noninverting input by 200mV or
more, while at the same time the noninverting input is
within 300mV of ground (V–), then the supply current will
increase by 1mA and the noninverting input current will
increase to about 10µA. This should be kept in mind in
comparator applications where the inverting input stays
above ground (V–) and the noninverting input is at or near
ground (V–).
Feedback Components
Because the input currents of the LT1211/LT1212 are less
than 125nA, it is possible to use high value feedback
resistors to set the gain. However, care must be taken to
insure that the pole that is formed by the feedback resis-
tors and the input capacitance does not degrade the
stability of the amplifier. For example, if a single supply,
noninverting gain of two is set with two 20k resistors, the
LT1211/LT1212 will probably oscillate. This is because
the amplifier goes open-loop at 3MHz (6dB of gain) and
has 50° of phase margin. The feedback resistors and the
10pF input capacitance generate a pole at 1.6MHz that
introduces 63° of phase shift at 3MHz! The solution is
simple; use lower value resistors or add a feedback
capacitor of 10pF or more.
Output
The output of the LT1211/LT1212 will swing to within
0.60V of the positive supply with no load. The open-loop
output resistance, when the output is driven hard into the
14
LT1211/ LT1212
O U
W
U
PPLICATI
A
S I FOR ATIO
following photos. These amplifiers are unity-gain stable
op amps and not fast comparators, therefore, the logic
being driven may oscillate due to the long transition time.
The output can be speeded up by adding 20mV or more of
hysteresis (positive feedback), but the offset is then a
function of the input direction.
Comparator Applications
Sometimes it is desirable to use an op amp as a compara-
tor. When operating the LT1211/LT1212 on a single 3.3V
or 5V supply, the output interfaces directly with most TTL
and CMOS logic.
The response time of the LT1211/LT1212 is a strong
function of the amount of input overdrive as shown in the
LT1211 Comparator Response (+)
20mV, 10mV, 5mV, 2mV Overdrives
LT1211 Comparator Response (–)
20mV, 10mV, 5mV, 2mV Overdrives
4
2
0
4
2
0
100
0
100
0
5µs/DIV
5µs/DIV
V = 5V
1211/12 AI01
S
V = 5V
1211/12 AI02
S
RL =
∞
RL =
∞
W
W
SI PLIFIED SCHE ATIC
+
V
I
6
I
1
I
4
I
3
I
5
I
2
Q13
BIAS
C
M
Q14
Q4
Q3
Q15
–IN
+IN
Q11
Q1
OUT
Q2
R
F
Q12
Q7
Q9
C
F
Q10
Q8
Q16
Q5
Q6
C
O
I
7
I
8
C
I
–
V
1211/12 SS
15
LT1211/ LT1212
U
O
TYPICAL APPLICATI S
1A Voltage-Controlled Current Source
+
V
1Ω
1k
1k
1k
500pF
V
IN
–
100Ω
1/2
Si9430DY
P-CHANNEL
LT1211
+
I
OUT
V
IN
1k
I
=
OUT
1Ω
t < 1µs
R
L
r
1211/12 TA04
1A Voltage-Controlled Current Sink
+
V
+
R
L
V
I
OUT
V
IN
+
100Ω
1/2
LT1211
Si9410DY
N-CHANNEL
–
500pF
1k
V
1Ω
IN
I
=
OUT
1Ω
t < 1µs
r
1211/12 TA05
16
LT1211/ LT1212
U
PACKAGE DESCRIPTIO
Dimensions in inches (millimeters) unless otherwise noted.
J8 Package
8-Lead CERDIP (Narrow 0.300, Hermetic)
(LTC DWG # 05-08-1110)
0.405
CORNER LEADS OPTION
(4 PLCS)
(10.287)
MAX
0.005
(0.127)
MIN
6
5
8
7
0.023 – 0.045
(0.584 – 1.143)
HALF LEAD
OPTION
0.025
0.220 – 0.310
0.045 – 0.068
(0.635)
RAD TYP
(5.588 – 7.874)
(1.143 – 1.727)
FULL LEAD
OPTION
1
2
3
4
0.200
(5.080)
MAX
0.300 BSC
(0.762 BSC)
0.015 – 0.060
(0.381 – 1.524)
0.008 – 0.018
0° – 15°
(0.203 – 0.457)
0.045 – 0.068
0.125
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE
OR TIN PLATE LEADS
(1.143 – 1.727)
3.175
MIN
0.100 ± 0.010
0.014 – 0.026
(2.540 ± 0.254)
(0.360 – 0.660)
J8 1197
17
LT1211/ LT1212
U
PACKAGE DESCRIPTIO
Dimensions in inches (millimeters) unless otherwise noted.
N8 Package
8-Lead PDIP (Narrow 0.300)
(LTC DWG # 05-08-1510)
0.400*
(10.160)
MAX
8
7
6
5
0.255 ± 0.015*
(6.477 ± 0.381)
1
2
4
3
0.130 ± 0.005
0.300 – 0.325
0.045 – 0.065
(3.302 ± 0.127)
(1.143 – 1.651)
(7.620 – 8.255)
0.065
(1.651)
TYP
0.009 – 0.015
0.125
(0.229 – 0.381)
0.020
(3.175)
MIN
+0.035
–0.015
(0.508)
MIN
0.325
0.100 ± 0.010
0.018 ± 0.003
+0.889
–0.381
8.255
(
)
(0.457 ± 0.076)
(2.540 ± 0.254)
N8 1197
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
N Package
14-Lead PDIP (Narrow 0.300)
(LTC DWG # 05-08-1510)
0.770*
(19.558)
MAX
14
13
12
11
10
9
8
0.255 ± 0.015*
(6.477 ± 0.381)
1
2
3
5
6
7
4
0.300 – 0.325
(7.620 – 8.255)
0.045 – 0.065
(1.143 – 1.651)
0.130 ± 0.005
(3.302 ± 0.127)
0.020
(0.508)
MIN
0.065
0.009 – 0.015
(0.229 – 0.381)
(1.651)
TYP
+0.035
–0.015
0.325
0.005
(0.125)
MIN
0.125
0.018 ± 0.003
+0.889
–0.381
(3.175)
MIN
(0.457 ± 0.076)
8.255
(
)
0.100 ± 0.010
N14 1197
(2.540 ± 0.254)
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
18
LT1211/ LT1212
U
PACKAGE DESCRIPTIO
Dimensions in inches (millimeters) unless otherwise noted.
S8 Package
8-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
0.189 – 0.197*
(4.801 – 5.004)
7
5
8
6
0.150 – 0.157**
(3.810 – 3.988)
0.228 – 0.244
(5.791 – 6.197)
1
3
4
2
0.010 – 0.020
(0.254 – 0.508)
× 45°
0.053 – 0.069
(1.346 – 1.752)
0.004 – 0.010
(0.101 – 0.254)
0.008 – 0.010
(0.203 – 0.254)
0°– 8° TYP
0.016 – 0.050
0.406 – 1.270
0.050
(1.270)
TYP
0.014 – 0.019
(0.355 – 0.483)
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
SO8 0996
S Package
16-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
0.386 – 0.394*
(9.804 – 10.008)
16
15
14
13
12
11
10
9
0.150 – 0.157**
(3.810 – 3.988)
0.228 – 0.244
(5.791 – 6.197)
5
7
8
1
2
3
4
6
0.010 – 0.020
(0.254 – 0.508)
× 45°
0.053 – 0.069
(1.346 – 1.752)
0.004 – 0.010
(0.101 – 0.254)
0.008 – 0.010
(0.203 – 0.254)
0° – 8° TYP
0.050
(1.270)
TYP
0.014 – 0.019
(0.355 – 0.483)
0.016 – 0.050
0.406 – 1.270
S16 0695
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tationthattheinterconnectionofits circuits as describedhereinwillnotinfringeonexistingpatentrights.
19
LT1211/ LT1212
U
TYPICAL APPLICATIO
Single Supply, 100kHz, 4th Order Butterworth Lowpass Filter
C1
1000pF
C2
1000pF
R1
2.94k
1000pF
R2
866Ω
–
V
IN
–
1000pF
1/4
1/4
LT1211
1.21k
1/4
+
–
LT1211
2.10k
1/4
LT1211
+
–
V
OUT
+
2.94k
20k
LT1211
+
1. 21k
1211/12 TA03a
3.3V
+
10
0
13k
1µF
–10
–20
–30
–40
–50
–60
–70
–80
–90
12-BIT ACCURATE SIGNAL RANGE FROM 6mV TO 1.8V ON 3.3V SINGLE SUPPLY.
MAXIMUM OUTPUT OFFSET ERROR IS 676µV.
FOR EACH 2ND ORDER SECTION:
1
C1C2R1R2
1
W QC1
O
Q
2
W
=
O
R1 =
R2 =
W C2
O
10k
100k
1M
10M
FREQUENCY (Hz)
1211/12 TA03b
RELATED PARTS
PART NUMBER
LT1213/LT1214
LT1215/LT1216
LT1498/LT1499
LT1630/LT1631
LT1632/LT1633
DESCRIPTION
COMMENTS
28MHz, 12V/µs, Single Supply Dual and Quad Precision Op Amps
23MHz, 50V/µs, Single Supply Dual and Quad Precision Op Amps
Twice as Fast as LT1211
Seven Times LT1211 Slew Rate
Rail-to-Rail LT1211
10MHz, 6V/µs, Dual/Quad Rail-to-Rail Input and Output Precision C-Load Op Amps
30MHz, 10V/µs, Dual/Quad Rail-to-Rail Input and Output Precision Op Amps
45MHz, 45V/µs, Dual/Quad Rail-to-Rail Input and Output Precision Op Amps
Rail-to-Rail LT1213
Rail-to-Rail LT1215
12112fa LT/TP 0798 2K REV A • PRINTED IN USA
LINEAR TECHNOLOGY CORPORATION 1993
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
20
●
●
(408)432-1900 FAX:(408)434-0507 www.linear-tech.com
相关型号:
LT1212CS#PBF
LT1212 - 14MHz, 7V/µs, Single Supply Dual and Quad Precision Op Amps; Package: SO; Pins: 16; Temperature Range: 0°C to 70°C
Linear
LT1212CS#TR
LT1212 - 14MHz, 7V/µs, Single Supply Dual and Quad Precision Op Amps; Package: SO; Pins: 16; Temperature Range: 0°C to 70°C
Linear
©2020 ICPDF网 联系我们和版权申明