EVM-GNSS-TM [LINX]
GPS / GNSS Receiver Master Development System;型号: | EVM-GNSS-TM |
厂家: | Linx Technologies |
描述: | GPS / GNSS Receiver Master Development System 全球定位系统 |
文件: | 总9页 (文件大小:2673K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
GPS / GNSS Receiver Master
Development System
User's Guide
Warning: Some customers may want Linx radio frequency (“RF”)
!
Table of Contents
products to control machinery or devices remotely, including machinery
or devices that can cause death, bodily injuries, and/or property
damage if improperly or inadvertently triggered, particularly in industrial
settings or other applications implicating life-safety concerns (“Life and
Property Safety Situations”).
1 Introduction
2 Ordering Information
3 Receiver Development Board
3 Board Objects
4 Initial Setup
4 Troubleshooting
5 The Prototyping Area
6 The Receiver Section
7 The USB Section
8 The Display Section
9 Master Development Software
10 Schematics
NO OEM LINX REMOTE CONTROL OR FUNCTION MODULE
SHOULD EVER BE USED IN LIFE AND PROPERTY SAFETY
SITUATIONS. No OEM Linx Remote Control or Function Module
should be modified for Life and Property Safety Situations. Such
modification cannot provide sufficient safety and will void the product’s
regulatory certification and warranty.
Customers may use our (non-Function) Modules, Antenna and
Connectors as part of other systems in Life Safety Situations, but
only with necessary and industry appropriate redundancies and
in compliance with applicable safety standards, including without
limitation, ANSI and NFPA standards. It is solely the responsibility
of any Linx customer who uses one or more of these products to
incorporate appropriate redundancies and safety standards for the Life
and Property Safety Situation application.
Do not use this or any Linx product to trigger an action directly
from the data line or RSSI lines without a protocol or encoder/
decoder to validate the data. Without validation, any signal from
another unrelated transmitter in the environment received by the
module could inadvertently trigger the action.
All RF products are susceptible to RF interference that can prevent
communication. RF products without frequency agility or hopping
implemented are more subject to interference. This module does not
have a frequency hopping protocol built in.
Do not use any Linx product over the limits in this data guide.
Excessive voltage or extended operation at the maximum voltage could
cause product failure. Exceeding the reflow temperature profile could
cause product failure which is not immediately evident.
Do not make any physical or electrical modifications to any Linx
product. This will void the warranty and regulatory and UL certifications
and may cause product failure which is not immediately evident.
GPS/GNSS Master Development System
User's Guide
Figure 1: GPS / GNSS Master Development System
Introduction
The Linx GPS and GNSS modules offer a simple, efficient and
cost-effective method of adding GPS or GNSS capabilities to any product.
The Master Development System is intended to give a designer all the tools
necessary to correctly incorporate the modules into an end product. The
development boards themselves serve several important functions:
•ꢀ Rapid Module Evaluation: The boards allow the performance of the
modules to be evaluated quickly in a user’s environment.
•ꢀ Application Development: An onboard prototyping area allows for the
development of custom circuits directly on the development board. All
signal lines are available on a header for easy access.
•ꢀ Design Benchmark: The boards provide a known benchmark against
which the performance of a custom design may be judged.
The Master Development System includes one assembled development
board, one receiver module on an evaluation board, one spare receiver
module for use on your first prototype, one SH Series active GPS antenna,
4 AAA batteries and full documentation.
1
–
–
Revised 3/18/2015
Ordering Information
Receiver Development Board
2
Ordering Information
8
Part Number
Description
4
3
MDEV-GPS-R4
MDEV-GPS-F4
MDEV-GPS-RM
MDEV-GPS-FM
MDEV-GNSS-GM
MDEV-GNSS-TM
EVM-GPS-R4
R4 Series Master Development System
F4 Series Master Development System
RM Series Master Development System
FM Series Master Development System
GM Series Master Development System
TM Series Master Development System
R4 Series Evaluation Module
7
9
1
6
10
5
EVM-GPS-F4
F4 Series Evaluation Module
EVM-GPS-RM
EVM-GPS-FM
RM Series Evaluation Module
FM Series Evaluation Module
11
EVM-GNSS-GM
EVM-GNSS-TM
RXM-GPS-R4-x
RXM-GPS-F4-x
RXM-GPS-RM-x
RXM-GPS-FM-x
RXM-GNSS-GM-x
RXM-GNSS-TM-x
GM Series Evaluation Module
TM Series Evaluation Module
Figure 3: Receiver Development Board
R4 Series GPS Receiver Module
F4 Series GPS Receiver Module
RM Series GPS Receiver Module
FM Series GPS Receiver Module
GM Series GNSS Receiver Module
TM Series GNSS Receiver Module
Board Objects
1. Four AAA Batteries (on back)
2. Power Switch
3. Voltage Regulator
4. USB Interface Module
5. Prototype Area
6. Break-Out Header
7. Receiver Evaluation Board
Figure 2: Ordering Information
8. CR2032 Backup Battery (on back)
9. Module Data Routing Switch
10. OLED Display
11. OLED Display Power Switch
3
–
–
–
–
2
Initial Setup
The Prototyping Area
Unpack the development system and install the AAA and coin-cell
batteries. Connect the external GPS antenna. The power switch selects
between the battery pack or USB power if the board is plugged into a
USB bus. To use the display, turn the OLED display power switch on. The
development board is now ready for use. After turning on the power, the
module determines its current position. Please note, the time required for
an initial fix or after long periods of storage is considerably greater than in
subsequent operation. Please refer to the module’s data guide for complete
information regarding Time-To-First-Fix (TTFF). To protect the display and
extend its life, turn off the display before turning off the board.
In addition to its evaluation functions, the board may also be used for
actual product development. It features a prototyping area to facilitate the
addition of application-specific circuitry. The prototyping area contains a
large area of plated through-holes so that external circuitry can be placed
on the board. The holes are set at 0.100” on center with a 0.040” diameter,
making it easy to add most industry-standard SIP and DIP packages.
External circuitry can be easily interfaced with the receiver through the
breakout header (J3) on the upper right of the prototyping area. A switch
controls the routing of data into the receiver module. By default the switch
is set for operation with the on-board USB module. When communicating
with the module from the prototyping area this switch should be set
to Prototype Control. At the bottom of the prototyping area is a row
connected to ground and at the top is a row connected to the 3.3V power
supply.
Troubleshooting
If the boards fail to work out of the box, then try the following:
•ꢀ Check the batteries to make sure they are not dead
•ꢀ Check to make sure that the power switch is in the correct position
•ꢀ Check that the antenna is installed correctly
Note: The on-board 3.3-volt regulator has approximately 300mA of
headroom available for additional circuitry. If added circuitry requires a
higher current, the user must add an additional regulator to the prototype
area or power the board from an external supply.
•ꢀ Check that the data routing switch is set appropriately
If all of these appear to be in order, please call +1 800 736 6677 or e-mail
techsupport@linxtechnologies.com for technical support.
Data Routing
Switch
+3 Volt Bus
Ground Bus
Figure 4: The Development Board Prototyping Area
5
–
–
–
–
4
The Receiver Section
The USB Section
The development board features a Linx QS Series USB module for
interface to a PC. This allows the board to be used with the supplied
development software or with custom software developed by the user.
The receiver module is mounted on an evaluation board which plugs into
headers on the main development board. The evaluation board has an
SMA antenna connector to allow the attachment of many different styles of
GPS antennas, including the included SH Series active GPS antenna. Each
receiver module has its own evaluation board, but all of them are designed
to fit into the same socket on the main board.
Figure 6: The Development Board USB Section
Drivers for the USB module are included on the software CD in the kit
or may be downloaded from www.linxtechnologies.com. Additional
information on using the QS Series USB module can also be found on the
website.
Figure 5: The Development Board Receiver Section
On the bottom of the main board is a CR2032 coin cell battery that
provides power to the Real Time Clock (RTC) and SRAM when the receiver
is powered down. This allows the receiver to start up and obtain a position
fix faster. This cell provides about two years of operation.
The USB connection also allows the board to be powered by the USB
bus instead of batteries. This can be convenient during development to
eliminate the need for frequent battery replacement.
7
–
–
–
–
6
The Display Section
Master Development Software
The Master Development System features an OLED screen that displays
the navigation information from the receiver module. This allows the
development board to act as a stand-alone evaluation system without the
need for any additional software.
The development system is supplied with Windows-based software that
communicates with the development board through the USB module. This
software displays the information from the receiver module in the different
NMEA formats and the satellite information, signal strength, and positions
are displayed graphically. If the PC is connected to the internet, the
software plots the current location on Google Maps. Full details are in the
software’s User’s Guide.
Figure 7: The Development Board Display Section
The display is driven by an on-board microcontroller located under
the display. Data from the receiver module is connected directly to this
microcontroller. The microcontroller receives data at the receiver’s default
9,600bps.
Note: If the receiver’s baud rate is changed, it will not be able to
communicate with the microcontroller.
The display and microcontroller pull about 100mA when fully powered, so
a power switch is supplied to deactivate the display area when not in use,
saving battery life. To protect the display and extend its life, be sure to turn
the display section off before turning off the main power to the board.
Figure 8: Master Development Software
9
–
–
–
–
8
Schematics
GND
J4
J5
C15
10uF
GND
GPIOD
GPIOE
TXM
RXM
1PPS
1
2
3
4
5
6
7
8
GND
VCC
1
2
3
4
5
6
7
8
+
VCC
VBACKUP
B2
BATHLD-001
VBACKUP
GPIOC
GPIOB
GPIOA
GND
RESET
RFPWRUP
ON_OFF
GND
GND
9
10
9
10
1
2
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
D5
D6
D7
PMD5/RE5
SOSC0/T1CK/CN0/RC14
SOSCI/CN1/RC13
OC1/RD0
PMD6/RE6
SW2
VCC
VCC
GND
3
PMD7/RE7
Figure 9: Receiver Section Schematic
4
D8
PMA5/SCK2/CN8/RG6
PMA4/SDI2/CN9/RG7
PMA3/SDO2/CN10/RG8
MCLR
IC4/PMCS1/INT4/RD11
IC3/PMCS2/INT3/RD10
IC2/U1CTS/INT2/RD9
IC1/RTCC/INT1/RD8
VSS
5
J3
R14
100k
SW2
POWER SWITCH
VCC
6
TXM
RXMHDR
1PPS
1
2
3
4
5
6
7
8
7
U5
VPP
GND
8
PMA2/SS2/CN11/RG9
VSS
GND
RFPWRUP
ON_OFF
GPIOE
SW3
9
RXMHDR
GND
VCC
OSC2/CLKO/RC15
OSC1/CLKI/RC12
VDD
RXM
10
11
12
13
14
15
16
RXMUSB
VDD
GPIOD
GPIOC
GPIOB
GPIOA
C1IN+/AN5/CN7/RB5
C1IN-/AN4/CN6/RB4
C2IN+/AN3/CN5/RB3
C2IN-/AN2/SS1/CN4/RB2
PGC1/EMUC1/VREF-/AN1/CN3/RB1
PGD1/EMUD1/PMA6/VREF+/AN0/CN2/RB0
VCC
9
10
SCL1/RG2
RES#
SDA1/RG3
CS#
U1RTS/BCLK1/SCK1/INT0/RF6
U1RX/SDI1/RF2
U1TX/SDO1/RF3
Figure 10: Header Section Schematic
PGC
PGD
TXM
GND
C3
10pF
J2
C6
10pF
USB-B
4
U4
GND
3
R4
10
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
DAT+
2
USBDP
USBDM
GND
RI
DCD
DSR
DAT-
1
R5 10
5V
GND
VCC
DATA IN
TXM
RXM USB
L1
SUSP IND
TX IND
RX IND
SUSP IND DATA OUT
RX IND
TX IND
485 TX
RTS
CTS
DTR
+
C7
0.1uF
C4
4.7uF
C2
0.01uF
R1
0
SDM-USB-QS
VCCGND
GNDVCC
GND
GND GND
U2
R7 200
R8 200
R3
/FAULT
TX IND
RX IND
/FAULT
100k
VCC
D2 TX_IND
GND
VCCU
C17
J6
1
2
3
6
5
4
C12
4.7uF
IN
OUT
ILIM
GND
VCC
VCOMH
VDDIO
VSL
1
2
3
4
5
6
7
8
+
+
C14
10uF
VCC13
VCC
C1
0.1uF
GND
GND
GND
D3 RX_IND
100uF
SUSP IND
EN
/FAULT
R9 200
GND
GND
GND
R6
D6
D7
53.6k
D7
D6
D5
D4
D4 Over Current
TPS2553
9
GND
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
D3
D2
D1
D0
E/RD#
R/W#
BS0
BS1
CS#
D/C#
RES#
IREF
GPIO1
GPIO0
R13
51
Figure 11: USB Section Schematic
GND
VCC
GND
VCC13
VCCU
SW1
L2 10uH
U3
R12
560k
GND
C11
D5
D9
R10
47.5k
5
1
2
3
C9
C10
B1
VIN
SW
GND
FB
VCC
GND
VDD
VCI
VSS
C8
10uF
U1
10uF
0.1uF
GND
1
3
1uF
Vin
Vout
R11
4.99k
GND
4
EN
VCC
R2
200
GND
GND
GND
GND
+
C13
0.1uF
C16
10uF
C5
100uF
D1
GRN
GND
GND
GND
GND
GND
Figure 13: Display Section Schematic
Figure 12: Power Supply Schematic
11
–
–
–
–
10
Linx Technologies
159 Ort Lane
Merlin, OR, US 97532
Phone: +1 541 471 6256
Fax: +1 541 471 6251
www.linxtechnologies.com
Disclaimer
Linx Technologies is continually striving to improve the quality and function of its products. For this reason, we
reserve the right to make changes to our products without notice. The information contained in this Data Guide
is believed to be accurate as of the time of publication. Specifications are based on representative lot samples.
Values may vary from lot-to-lot and are not guaranteed. “Typical” parameters can and do vary over lots and
application. Linx Technologies makes no guarantee, warranty, or representation regarding the suitability of any
product for use in any specific application. It is the customer’s responsibility to verify the suitability of the part for
the intended application. NO LINX PRODUCT IS INTENDED FOR USE IN ANY APPLICATION WHERE THE SAFETY
OF LIFE OR PROPERTY IS AT RISK.
Linx Technologies DISCLAIMS ALL WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. IN NO EVENT SHALL LINX TECHNOLOGIES BE LIABLE FOR ANY OF CUSTOMER’S INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING IN ANY WAY FROM ANY DEFECTIVE OR NON-CONFORMING PRODUCTS
OR FOR ANY OTHER BREACH OF CONTRACT BY LINX TECHNOLOGIES. The limitations on Linx Technologies’
liability are applicable to any and all claims or theories of recovery asserted by Customer, including, without
limitation, breach of contract, breach of warranty, strict liability, or negligence. Customer assumes all liability
(including, without limitation, liability for injury to person or property, economic loss, or business interruption) for
all claims, including claims from third parties, arising from the use of the Products. The Customer will indemnify,
defend, protect, and hold harmless Linx Technologies and its officers, employees, subsidiaries, affiliates,
distributors, and representatives from and against all claims, damages, actions, suits, proceedings, demands,
assessments, adjustments, costs, and expenses incurred by Linx Technologies as a result of or arising from any
Products sold by Linx Technologies to Customer. Under no conditions will Linx Technologies be responsible for
losses arising from the use or failure of the device in any application, other than the repair, replacement, or refund
limited to the original product purchase price. Devices described in this publication may contain proprietary,
patented, or copyrighted techniques, components, or materials. Under no circumstances shall any user be
conveyed any license or right to the use or ownership of such items.
©2015 Linx Technologies. All rights reserved.
The stylized Linx logo, Wireless Made Simple, WiSE, CipherLinx and the stylized CL logo are trademarks of Linx Technologies.
相关型号:
EVM1DSW30B34
Trimmer, Cermet, 0.2W, 30000ohm, 50V, 25% +/-Tol, -250,250ppm/Cel, 1 Turn(s), 1815, 4MM, SQUARE, 3PINS, ROHS COMPLIANT
PANASONIC
EVM1DSW30B52
Trimmer, Cermet, 0.2W, 500ohm, 50V, 25% +/-Tol, -250,250ppm/Cel, 1 Turn(s), 1815, 4MM, SQUARE, 3PINS, ROHS COMPLIANT
PANASONIC
EVM1DSW30B53
Trimmer, Cermet, 0.2W, 5000ohm, 50V, 25% +/-Tol, -250,250ppm/Cel, 1 Turn(s), 1815, 4MM, SQUARE, 3PINS, ROHS COMPLIANT
PANASONIC
EVM1DSW30BC2
Trimmer, Cermet, 0.2W, 150ohm, 50V, 25% +/-Tol, -250,250ppm/Cel, 1 Turn(s), 1815, 4MM, SQUARE, 3PINS, ROHS COMPLIANT
PANASONIC
©2020 ICPDF网 联系我们和版权申明