T550B107K060AT4251 [KEMET]
Includes F-Tech anode which eliminates hidden defects;型号: | T550B107K060AT4251 |
厂家: | KEMET CORPORATION |
描述: | Includes F-Tech anode which eliminates hidden defects |
文件: | 总12页 (文件大小:1846K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC
and DLA Series
Overview
The KEMET T550 Series Polymer Hermetic Seal (PHS) is a
tantalum capacitor with a Ta anode and Ta2O5 dielectric. A
conductive organic polymer replaces the traditionally used MnO2
or wet electrolyte as the cathode plate of the capacitor. This
results in very low ESR and improved capacitance retention
at high frequency and low temperature. The T550 Series PHS
also exhibits a benign failure mode which eliminates the case
breach that can occur in wet tantalum types. Additionally, this
part may be operated at voltages up to 80% of rated voltage
with equivalent or better reliability than traditional MnO2 or wet
tantalum capacitors operated at 50% of rated voltage.
T550 Series PHS also offers higher ripple current handling
capability and a lower ESR range than wet tantalums. With
reduced ESR and enhanced capacitance retention at higher
frequencies and low temperatures, the T550 Series PHS provides
the highest total capacitance and the most economical solution for
high power applications, all within an approximately 25% lighter
package than the equivalent wet tantalum capacitor.
Benefits
• Includes F-Tech anode which eliminates hidden defects
in the dielectric
• 100% Simulated Breakdown Screening
• Maximum operating temperature of +105°C
• Meets all requirements of DLA Drawing 13030
• Polymer cathode technology
• Extremely low ESR
• High frequency capacitance retention
• Low temperature capacitance retention
• 100% accelerated steady state aging (240 hours)
• 100% surge current tested, 10 cycles +25°C
•ꢀ Volumetricallyꢀefficient
Click image above for interactive 3D content
Open PDF in Adobe Reader for full functionality
• Non-ignition failure mode
• Approximately 25% lighter than equivalent wet tantalum
• Case dimensions equivalent to MIL–PRF–39006/22/25/30/31
Applications
Typicalꢀapplicationsꢀincludeꢀhighꢀvoltageꢀpowerꢀmanagementꢀsuchꢀasꢀbuck/boostꢀconverters,ꢀfiltering,ꢀhold-upꢀcapacitors,ꢀandꢀotherꢀ
high ripple current applications.
One world. One KEMET
1
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2059_T550 • 6/23/2016
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
Ordering Information
T
550
Series
550 =
B
107
M
025
A
T
4251
Capacitor
Class
Case Capacitance Capacitance Rated Voltage
Size
Termination
Finish
Surge
Option
Sleeve Option
Product Level
Code (pF)
Tolerance
(VDC)
Blank = Sleeved
0100 = Unsleeved
7200 = Tape &
Reel
7293 & 7443 =
Ammo
T =
B
First two digits K = ±10% 006 = 6.3
A = N/A
B* = DLA
13030
Standard
reliability
T* = DLA
13030 High
reliability
T = 100% tin Blank = 25°C ±5°C, 10
(Sn) plated cycles, after constant
H = Tin/lead voltage conditioning
(SnPb) solder (KEMET standard)
coated
(5% Pb
minimum)
Tantalum Polymer
Hermetic
represent
significantꢀ
figures.ꢀThirdꢀ
digitꢀspecifiesꢀ
number of
zeros.
M = ±20% 008 = 8
015 = 15
Seal
025 = 25
040 = 40
050 = 50
060 = 60
4251 = 10 cycles, -55°C and
+85°C after voltage aging
4252 = 10 cycles, -55°C and
+85°C before voltage aging
075 = 75
100 = 100
* Only available on select parts. Refer to part number table for details.
Ordering Information – DLA Series
13030
-01
K
A
S
L
B
Drawing
Number Number Tolerance
Dash Capacitance
Lead
Length
Product
Level
Surge Current Testing
Insulation
See
Part
Number
Table
K = ±10% A = +25°C ± 5°C, 10 cycles,
M = ±20% after constant voltage
conditioning (KEMET standard)
B = -55°C -5°C, +0°C and
+85°C ± 5°C; after constant
voltage conditioning.
S = Sleeved
U = Unsleeved
L = 1.50
inches
(standard) T = High
reliability
B = Standard
reliability
C = -55°C -5°C, +0°C and
+85°C ± 5°C; before constant
voltage conditioning.
* Standard terminations for DLA PN's is "H" (SnPb)
Performance Characteristics
Item
Performance Characteristics
Operating Temperature
Rated Capacitance Range
Capacitance Tolerance
Rated Voltage Range
DF (120 Hz at 25°C)
ESR (100 kHz at 25°C)
-55°C to 105°C
20ꢀμFꢀtoꢀ820ꢀμFꢀatꢀ120ꢀHz/25°Cꢀ*
K Tolerance (10%), M Tolerance (20%)
6 – 100 V
ReferꢀtoꢀPartꢀNumberꢀElectricalꢀSpecificationꢀTableꢀ
ReferꢀtoꢀPartꢀNumberꢀElectricalꢀSpecificationꢀTableꢀꢀ
ReferꢀtoꢀPartꢀNumberꢀElectricalꢀSpecificationꢀTable
(at rated voltage up to +85°C and 78% of rated voltage applied at 105°C)
Leakage Current
Packaging
According MIL–PRF–39006
KEMET does not recommend storage above 85ºC.
* Additional case sizes and capacitance/voltage are under development.
2
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2059_T550 • 6/23/2016
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
Qualification
Test Performed
Method Reference
Test Conditions
Reliability and Environmental Tests
85˚C,ꢀ40ꢀkHzꢀrippleꢀcurrent,ꢀ2,000ꢀhours
ACꢀRippleꢀLifeꢀatꢀ85˚C
85˚CꢀLife
MIL–PRF–39006
MIL–PRF–39006
KEMET Standard
MIL–PRF–39006
MIL–PRF–39003
MIL–PRF–39006
KEMET Catalog
85˚C,ꢀratedꢀvoltage,ꢀ2,000ꢀhours
105˚CꢀLife
105°C, 0.78 x rated voltage, 2,000 hours
Surge Voltage
85˚C,ꢀ1.15ꢀxꢀratedꢀvoltage,ꢀ1,000ꢀcycles,ꢀexceptꢀdeltaꢀcapꢀshallꢀbeꢀ+10%/-20%
+25 ºC, 10 cycles (Option A), Option B available
-62˚Cꢀforꢀ72ꢀhoursꢀfollowedꢀbyꢀ1ꢀhourꢀatꢀ125˚C
Surge Current
Low Temperature Storage
Reverse Voltage
1 V for 8 hours maximum at 25°C, 1 V for 2 hours maximum at 70°C
Physical, Mechanical and Process Tests
Visual and Mechanical
Examination (Internal and
External)
MIL–PRF–39006
Case dimensions, marking
Terminal Strength
Resistance to Solvents
Resistance to Soldering Heat
Solderability
MIL–PRF–39006
MIL–PRF–39006
MIL–PRF–39006
MIL–PRF–39006
Pull test and wire lead bend test
Immersion in (3) solvents
Immersed to within 0.05 inch of capacitor body
Depthꢀofꢀinsertionꢀinꢀfluxꢀandꢀsolderꢀtoꢀwithinꢀ0.062ꢀinchꢀofꢀweldedꢀjoint
Shock Method 213, Condition I, 100 g peak, Vibration Method 204, Condition D,
20 g peak
Shock and Vibration
MIL–STD–202, Methods 213, 204
Barometric Pressure (Reduced)
Salt Atmosphere (Corrosion)
Moisture Resistance
MIL–PRF–39006
MIL–PRF–39006
MIL–PRF–39006
MIL–PRF–39006
MIL–PRF–39003
150,000 feet for 5 minutes, voltage applied for 1 minute
Subjectedꢀtoꢀfineꢀmistꢀofꢀsaltꢀsolution
65˚Cꢀatꢀ6ꢀvolts
Dielectric Withstanding Voltage
Insulation Resistance
2,000 VDC, 60 seconds, sleeving examined for evidence of breakdown
500ꢀVDC,ꢀ1ꢀminute,ꢀinsulationꢀresistanceꢀnotꢀlessꢀthanꢀ1,000ꢀMΩ
Electrical Characterization
Temperature Stability
Frequency Scan
Reference MIL–PRF–39006
KEMET Standard
-55˚Cꢀtoꢀ105˚C
Impedance, ESR and capacitance versus frequency
3
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2059_T550 • 6/23/2016
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
Qualification – DLA Approval Inspection
DLA Requirement
Paragraph
Inspection
Test Name
SS/Lot
Shockꢀ(SpecifiedꢀPulse)1
Vibration, High Frequency1
Thermal Shock
3.3.4
3.3.5
3.3.6
3.3.7
3.3.8
3.3.9
3.3.10
3.3.11
3.3.12
Group I
6 per case size
Salt Atmosphere
Solderability
Terminal Strength
Surge Voltage2
Moisture Resistance
Group II
Group III
12
Dielectric Withstanding Voltage
Insulation Resistance
Low Temperature (Storage)
Stability at Low and High Temperatures
Reverse Voltage
3.3.13
3.3.14
3.3.15
3.3.23
3.3.16
3.3.18
3.3.17
3.3.20
3.3.21
3.3.22
13
12 per condition
102
Group IV
Group V
Lifeꢀatꢀ85˚C
AC Ripple Life at 85ºC
Life at 105ºC
8 per case size
Group VI
Group VII
40
6
Barometric Pressure
Resistance to Solvents
Resistance to Soldering Heat
1 No failures for mechanical shock or vibration tests shall be permitted.
2 Surge voltage change in capacitance limits are wider than those in some subsequent tests.
It may be necessary to perform initial measurements again, prior to the individual tests of Group II.
Product Level:
Inspection of product for delivery shall consist of:
B level
T level
GroupꢀAꢀinspectionꢀspecifiedꢀinꢀDrawingꢀ13030
GroupꢀAꢀandꢀgroupꢀBꢀinspectionsꢀspecifiedꢀinꢀDrawingꢀ13030
4
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2059_T550 • 6/23/2016
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
Electrical Characteristics
ESR vs. Frequency
10.0
+125°C
+50°C
0°C
+85°C
+25°C
-25°C
-80°C
-55°C
1.0
0.1
0.0
10
100
1,000
10,000
100,000
1,000,000
10,000,000
Frequency (Hz)
Capacitance vs. Frequency
120
100
80
60
40
20
0
+125°C
+50°C
0°C
+85°C
+25°C
-25°C
-80°C
-55°C
10
100
1,000
10,000
100,000
1,000,000
Frequency (Hz)
5
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2059_T550 • 6/23/2016
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
Dimensions – Inches (Millimeters)
SIDE VIEW
END VIEW
D
0.094 (2.39) Maximum
1.50 ±0.250
(38.10 ±6.35)
C
1.50 ±0.250
(38.10 ±6.35)
+
B
L
Insulated Case
D
Case Code
Case Size
MIL-PRF-39006
T2
Uninsulated Case
D
J
max
L
L
M
+0.016 (0.41)
-0.015 (0.38)
+0.016 (0.41)
-0.015 (0.38)
± 0.031 (0.79)
±0.031 (0.79)
±0.002 (0.05)
0.822 (20.88)
0.289 (7.34)
0.686 (17.42)
B
0.650 (16.51)
0.279 (7.09)
0.025 (0.64)
Table 1 – Ratings & Part Number Reference
Rated
V o l t a g e Capacitance
Rated
Case
Size
KEMET Part
Number
DLA
Drawing Number
DC
Leakage
Maximum
Ripple
Current
DF
ESR
µA at 25°C
Maximum/5 Minutes 120 Hz Max
% at 25ºC
mΩ at 25ºC
100 kHz
mArms at
85ºC/40 kHz
(V) 85ºC
µF
KEMET/EIA (See below for part options) (See below for part options)
6
6
8
8
140
820
220
680
100
180
560
70
120
390
50
100
40
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
T550B147(1)006A(3)
T550B827(1)006A(3)
T550B227(1)008A(3)
T550B687(1)008A(3)
T550B107(1)010A(3)
T550B187(1)010A(3)
T550B567(1)010A(3)
T550B706(1)015A(3)
T550B127(1)015A(3)
T550B397(1)015A(3)
T550B506(1)025A(3)
T550B107(1)025(2)(3)
T550B406(1)030A(3)
T550B686(1)030A(3)
T550B337(1)035A(3)
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
6.3
36.9
13.2
40.8
7.5
13.5
42.0
7.9
13.5
43.9
9.4
18.8
9.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
10.0
120
90
120
90
140
110
90
140
110
90
170
190
170
140
180
1510
1750
1510
1750
1400
1580
1750
1400
1580
1750
1275
1200
1275
1400
1240
10
10
10
15
15
15
25
25
30
30
35
N/A
N/A
N/A
13030-01(1)(4)(5)L(6)
N/A
N/A
N/A
68
330
15.3
86.6
40
40
50
50
50
50
60
60
60
75
100
100
120
25
B
B
B
B
B
B
B
B
B
B
B
T550B107(1)040(2)(3)
T550B127(1)040(2)(3)
T550B256(1)050A(3)
T550B476(1)050A(3)
T550B107(1)050(2)(3)
T550B127(1)050(2)(3)
T550B206(1)060A(3)
T550B396(1)060A(3)
T550B107(1)060(2)(3)
T550B756(1)075(2)(3)
T550B256(1)100(2)(3)
13030-02(1)(4)(5)L(6)
13030-03(1)(4)(5)L(6)
N/A
30.0
36.0
9.4
17.6
37.5
45.0
9.0
17.6
45.0
42.2
18.8
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
150
120
170
150
130
90
200
160
100
110
190
1350
1510
1275
1350
1450
1750
1175
1310
1660
1580
1200
47
N/A
100
120
20
39
100
13030-04(1)(4)(5)L(6)
13030-05(1)(4)(5)L(6)
N/A
N/A
13030-06(1)(4)(5)L(6)
13030-07(1)(4)(5)L(6)
13030-08(1)(4)(5)L(6)
75
25
(1) To complete KEMET part number, insert M for ±20% or K for ±10%. Designates capacitance tolerance.
(2) To complete KEMET part number, insert A = N/A, B= standard reliability, or T = high reliability.
(3) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated, H = Standard Solder coated (SnPb 5% Pb minimum). Designates termination finish.
(4) To complete the DLA PIN number, insert the surge current testing option, A = 25°C after voltage aging, B = -55°C +0°C and +85°C after voltage aging or C =
−55°C +0°C and +85°C before voltage aging
(5) To complete the DLA PIN number, insert the insulation option. S = Sleeved, U = Unseleeved.
(6) To complete the DLA PIN number, insert the product level option. B = standard reliability or T = high reliability.
Refer to Ordering Information for additional detail.
Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitution will be marked
with the higher voltage rating.
6
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2059_T550 • 6/23/2016
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
Recommended Voltage Derating Guidelines
120%
100%
80%
60%
40%
20%
0%
-55°C to 85°C
VR
85°C to 105°C
78% of VR
% Change in Working DC
Voltage with Temperature
Recommended Maximum
Application Voltage
% Change in Working DC Voltage
with Temperature
80%
78%
63%
80% of VR
63% of VR
Recommended Maximum Application
Voltage (As % of Rated Voltage)
(As % of Rated Voltage)
-55
25
45
85
105
Temperature (°C)
Ripple Current/Ripple Voltage
Permissible AC ripple voltage and current are related to equivalent series resistance (ESR) and the power dissipation capabilities of the
device. Permissible AC ripple voltage that may be applied is limited by two criteria:
1. The positive peak AC voltage plus the DC bias voltage, if any, must not exceed the DC voltage rating of the capacitor.
ꢀ 2.ꢀTheꢀnegativeꢀpeakꢀACꢀvoltageꢀinꢀcombinationꢀwithꢀbiasꢀvoltage,ꢀifꢀany,ꢀmustꢀnotꢀexceedꢀtheꢀallowableꢀlimitsꢀspecifiedꢀforꢀreverseꢀ
voltage.
The maximum power dissipation by case size can be determined using the below left table. The maximum power dissipation
rating stated in the table must be reduced with increasing environmental operating temperatures. Refer to the below right table for
temperature compensation requirements.
Using the Pmax of the device, the maximum allowable rms ripple
current or voltage may be determined.
Maximum Power
Dissipation (Pmax)
mWatts at 25°C
with +60°C Rise
Case Code
I(max) = √Pmax/R
E(max) = Z √Pmax/R
MIL–PRF–39006/22/
KEMET
B
25/30/31 Case Size
I = rms ripple current (amperes)
E = rms ripple voltage (volts)
T2
715
P
max = maximum power dissipation (watts)
R = ESR at specified frequency (ohms)
Z = Impedance at specified frequency (ohms)
Temperature Compensation Multipliers for
Maximum Power Dissipation (Pmax)
Tꢀ≤ꢀ45°C
45°Cꢀ<ꢀTꢀ≤ꢀ85°C
85°Cꢀ<ꢀTꢀ≤ꢀ105°C
0.10
The maximum power dissipation rating must be reduced with increasing
environmental operating temperatures. Refer to the Temperature Compensation
Multiplier table for details.
1.00
0.50
T= Environmental Temperature
7
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2059_T550 • 6/23/2016
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
Reverse Voltage
Solid tantalum polymer capacitors are polar devices and may be permanently damaged or destroyed if connected with the wrong
polarity. A small reverse voltage is permissible for time periods per the below table. KEMET can offer lower capacitance in this voltage
with higher reverse voltage capability. In addition, we continue to improve our capability for this characteristic.
Temperature
Permissible Reverse Voltage
25°C
70ºC
1 V for 8 hours Maximum
1 V for 2 hours Maximum
Optimum Solder Wave Profile
Mounting
All encased capacitors will pass the Resistance to Soldering Heat Test of MIL–STD–202, Method 210, Condition C. This test simulates
wave solder of topside board mount product. This demonstration of resistance to solder heat is in accordance with what is believed to
beꢀtheꢀindustryꢀstandard.ꢀMoreꢀsevereꢀtreatmentꢀmustꢀbeꢀconsideredꢀreflectiveꢀofꢀanꢀimproperꢀsolderingꢀprocess.ꢀTheꢀaboveꢀfigureꢀisꢀaꢀ
recommendedꢀsolderꢀwaveꢀprofileꢀforꢀbothꢀaxialꢀandꢀradialꢀleadedꢀsolidꢀtantalumꢀcapacitors.
8
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2059_T550 • 6/23/2016
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
Construction
Detailed Cross Section
Wire Lead (+)
Solder
(100% Sn / SnPb)
Wire Lead (-)
(100% Sn / SnPb)
Anode Tube
Hermetic Seal System
(Glass Seal and Ring)
Aluminum Can
Tantalum Pellet
(See Detail for Layers)
Solder
Hermetic Seal System
Aluminum Can
Tantalum Wire
(Ring)
Hermetic Seal System
(Glass Seal)
Silver Paint
(Fourth Layer)
Wire Lead (+)
(100% Sn / SnPb)
Carbon
(Third Layer)
Polymer
(Second Layer)
Ta2O5 Dielectric
(First Layer)
Tantalum Wire
Tantalum
Wire Lead (-)
(100% Sn / SnPb)
Anode Tube
Solder
Capacitor Marking
B Case
Series
Rated Capacitance
KT550
100µF
+
KEMET ID
Polarity Marks
10% 60V +
1202AAAA
Capacitance
Tolerance,
Rated Voltage
(VDC)
4 Digit Date Code, Lot Code
Date Code
3 Digit
4 Digit
5 = 2015
6 = 2016
7 = 2017
8 = 2018
9 = 2019
15 = 2015
16 = 2016
17 = 2017
18 = 2018
19 = 2019
Year
01 = 1st week of the year to
52 = 52nd week of the year
Week
9
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2059_T550 • 6/23/2016
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
Storage
Tantalum hermetically sealed capacitors should be stored in normal working environments. While the capacitors themselves are quite
robust in other environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres,
and long term storage. In addition, packaging materials will be degraded by high temperature– reels may soften or warp and tape peel
force may increase. KEMET recommends that maximum storage temperature not exceed 40ºC and maximum storage humidity not
exceedꢀ60%ꢀrelativeꢀhumidity.ꢀTemperatureꢀfluctuationsꢀshouldꢀbeꢀminimizedꢀtoꢀavoidꢀcondensationꢀonꢀtheꢀpartsꢀandꢀatmospheresꢀ
should be free of chlorine and sulphur bearing compounds. For optimized solderability capacitors stock should be used promptly,
preferably within three years of receipt.
Packaging
Case Size
Pieces per Tray
KEMET
EIA
B
T2
20
Weight
Case Size
Average Weight
(grams)
KEMET
EIA
B
T2
3.63
10
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2059_T550 • 6/23/2016
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
KEMET Corporation
World Headquarters
Europe
Asia
Southern Europe
Sasso Marconi, Italy
Tel: 39-051-939111
Northeast Asia
Hong Kong
Tel: 852-2305-1168
2835 KEMET Way
Simpsonville, SC 29681
Skopje,ꢀMacedonia
Tel: 389-2-55-14-623
Shenzhen, China
Tel: 86-755-2518-1306
Mailing Address:
P.O. Box 5928
Greenville, SC 29606
Beijing,ꢀChina
Central Europe
Landsberg, Germany
Tel: 49-8191-3350800
Tel: 86-10-5877-1075
www.kemet.com
Tel: 864-963-6300
Fax: 864-963-6521
Shanghai, China
Tel: 86-21-6447-0707
Kamen, Germany
Tel: 49-2307-438110
Corporate Offices
Fort Lauderdale, FL
Tel: 954-766-2800
Seoul, South Korea
Tel: 82-2-6294-0550
Northern Europe
Wyboston, United Kingdom
Tel: 44-1480-273082
Taipei, Taiwan
Tel: 886-2-27528585
North America
Northeast
Wilmington, MA
Tel: 978-658-1663
Espoo, Finland
Tel: 358-9-5406-5000
Southeast Asia
Singapore
Tel: 65-6701-8033
Southeast
Lake Mary, FL
Tel: 407-855-8886
Penang, Malaysia
Tel: 60-4-6430200
Central
Novi, MI
Tel: 248-994-1030
Bangalore, India
Tel: 91-806-53-76817
Irving, TX
Tel: 972-915-6041
West
Milpitas, CA
Tel: 408-433-9950
Mexico
Guadalajara,ꢀJaliscoꢀ
Tel: 52-33-3123-2141
Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not
assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of
KEMET Electronics Corporation.
11
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2059_T550 • 6/23/2016
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
Disclaimer
Allꢀproductꢀspeci ꢀcations,ꢀstatements,ꢀinformationꢀandꢀdataꢀ(collectively,ꢀtheꢀ“Information”)ꢀinꢀthisꢀdatasheetꢀareꢀsubjectꢀtoꢀchange.ꢀTheꢀcustomerꢀisꢀresponsibleꢀforꢀcheckingꢀandꢀ
verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.
All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
StatementsꢀofꢀsuitabilityꢀforꢀcertainꢀapplicationsꢀareꢀbasedꢀonꢀKEMETꢀElectronicsꢀCorporation’sꢀ(“KEMET”)ꢀknowledgeꢀofꢀtypicalꢀoperatingꢀconditionsꢀforꢀsuchꢀapplications,ꢀbutꢀareꢀ
notꢀintendedꢀtoꢀconstituteꢀ–ꢀandꢀKEMETꢀspeci ꢀcallyꢀdisclaimsꢀ–ꢀanyꢀwarrantyꢀconcerningꢀsuitabilityꢀforꢀaꢀspeci ꢀcꢀcustomerꢀapplicationꢀorꢀuse.ꢀTheꢀInformationꢀisꢀintendedꢀforꢀuseꢀonlyꢀ
by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise
provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained.
Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still
occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective
circuitryꢀorꢀredundancies)ꢀinꢀorderꢀtoꢀensureꢀthatꢀtheꢀfailureꢀofꢀanꢀelectricalꢀcomponentꢀdoesꢀnotꢀresultꢀinꢀaꢀriskꢀofꢀpersonalꢀinjuryꢀorꢀpropertyꢀdamage.
Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not
be required.
12
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2059_T550 • 6/23/2016
相关型号:
T550B107K075AH4251
Includes F-Tech anode which eliminates hidden defectsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
KEMET
T550B107K075AT4251
Includes F-Tech anode which eliminates hidden defectsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
KEMET
T550B107K100AH4251
Includes F-Tech anode which eliminates hidden defectsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
KEMET
T550B107K100AT4251
Includes F-Tech anode which eliminates hidden defectsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
KEMET
T550B107M006AH4251
Includes F-Tech anode which eliminates hidden defectsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
KEMET
T550B107M006AT4251
Includes F-Tech anode which eliminates hidden defectsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
KEMET
T550B107M008AH4251
Includes F-Tech anode which eliminates hidden defectsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
KEMET
T550B107M008AT4251
Includes F-Tech anode which eliminates hidden defectsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
KEMET
T550B107M015AH4251
Includes F-Tech anode which eliminates hidden defectsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
KEMET
T550B107M015AT4251
Includes F-Tech anode which eliminates hidden defectsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
KEMET
T550B107M025AH4251
Includes F-Tech anode which eliminates hidden defectsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
KEMET
T550B107M025AT4251
Includes F-Tech anode which eliminates hidden defectsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
KEMET
©2020 ICPDF网 联系我们和版权申明