C340C474Z3R5HA7303 [KEMET]
Ceramic Capacitor, Ceramic, 25V, 80% +Tol, 20% -Tol, X7R, -/+15ppm/Cel TC, 0.47uF, 4015,;型号: | C340C474Z3R5HA7303 |
厂家: | KEMET CORPORATION |
描述: | Ceramic Capacitor, Ceramic, 25V, 80% +Tol, 20% -Tol, X7R, -/+15ppm/Cel TC, 0.47uF, 4015, |
文件: | 总16页 (文件大小:965K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MULTILAYER CERAMIC CAPACITORS/AXIAL
& RADIAL LEADED
Multilayer ceramic capacitors are available in a
edges of the laminated structure. The entire structure is
fired at high temperature to produce a monolithic
block which provides high capacitance values in a
small physical volume. After firing, conductive
terminations are applied to opposite ends of the chip to
make contact with the exposed electrodes.
Termination materials and methods vary depending on
the intended use.
variety of physical sizes and configurations, including
leaded devices and surface mounted chips. Leaded
styles include molded and conformally coated parts
with axial and radial leads. However, the basic
capacitor element is similar for all styles. It is called a
chip and consists of formulated dielectric materials
which have been cast into thin layers, interspersed
with metal electrodes alternately exposed on opposite
TEMPERATURE CHARACTERISTICS
Ceramic dielectric materials can be formulated with
a wide range of characteristics. The EIA standard for
ceramic dielectric capacitors (RS-198) divides ceramic
dielectrics into the following classes:
Class III: General purpose capacitors, suitable
for by-pass coupling or other applications in which
dielectric losses, high insulation resistance and
stability of capacitance characteristics are of little or
no importance. Class III capacitors are similar to Class
II capacitors except for temperature characteristics,
Class I: Temperature compensating capacitors,
suitable for resonant circuit application or other appli-
cations where high Q and stability of capacitance char-
acteristics are required. Class I capacitors have
predictable temperature coefficients and are not
affected by voltage, frequency or time. They are made
from materials which are not ferro-electric, yielding
superior stability but low volumetric efficiency. Class I
capacitors are the most stable type available, but have
the lowest volumetric efficiency.
which are greater than
15%. Class III capacitors
have the highest volumetric efficiency and poorest
stability of any type.
KEMET leaded ceramic capacitors are offered in
the three most popular temperature characteristics:
C0G: Class I, with a temperature coefficient of 0
30 ppm per degree C over an operating
temperature range of - 55°C to + 125°C (Also
known as “NP0”).
Class II: Stable capacitors, suitable for bypass
or coupling applications or frequency discriminating
circuits where Q and stability of capacitance char-
acteristics are not of major importance. Class II
capacitors have temperature characteristics of 15%
or less. They are made from materials which are
ferro-electric, yielding higher volumetric efficiency but
less stability. Class II capacitors are affected by
temperature, voltage, frequency and time.
X7R: Class II, with a maximum capacitance
change of 15% over an operating temperature
range of - 55°C to + 125°C.
Z5U: Class III, with a maximum capacitance
change of + 22% - 56% over an operating tem-
perature range of + 10°C to + 85°C.
Specified electrical limits for these three temperature
characteristics are shown in Table 1.
SPECIFIED ELECTRICAL LIMITS
Temperature Characteristics
X7R
Parameter
C0G
Z5U
Dissipation Factor: Measured at following conditions.
C0G – 1 kHz and 1 vrms if capacitance >1000pF
1 MHz and 1 vrms if capacitance 1000 pF
X7R – 1 kHz and 1 vrms* or if extended cap range 0.5 vrms
Z5U – 1 kHz and 0.5 vrms
2.5%
(3.5% @ 25V)
0.10%
4.0%
Dielectric Stength: 2.5 times rated DC voltage.
Pass Subsequent IR Test
1,000 M
or 100 G
F
1,000 M
or 100 G
F
1,000 M
or 10 G
F
Insulation Resistance (IR): At rated DC voltage,
whichever of the two is smaller
Temperature Characteristics: Range, °C
Capacitance Change without
DC voltage
-55 to +125
30 ppm/°C
-55 to +125
15%
+ 10 to +85
+22%,-56%
0
* MHz and 1 vrms if capacitance 100 pF on military product.
Table I
4
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
APPLICATION NOTES FOR MULTILAYER
CERAMIC CAPACITORS
The variation of a capacitor’s impedance with frequency
determines its effectiveness in many applications.
ELECTRICAL CHARACTERISTICS
The fundamental electrical properties of multilayer
ceramic capacitors are as follows:
Dissipation Factor: Dissipation Factor (DF) is a mea-
sure of the losses in a capacitor under AC application. It is the
ratio of the equivalent series resistance to the capacitive reac-
tance, and is usually expressed in percent. It is usually mea-
sured simultaneously with capacitance, and under the same
conditions. The vector diagram in Figure 2 illustrates the rela-
tionship between DF, ESR, and impedance. The reciprocal of
the dissipation factor is called the “Q”, or quality factor. For
convenience, the “Q” factor is often used for very low values
of dissipation factor. DF is sometimes called the “loss tangent”
or “tangent ␦”, as derived from this diagram.
Polarity: Multilayer ceramic capacitors are not polar,
and may be used with DC voltage applied in either direction.
Rated Voltage: This term refers to the maximum con-
tinuous DC working voltage permissible across the entire
operating temperature range. Multilayer ceramic capacitors
are not extremely sensitive to voltage, and brief applications
of voltage above rated will not result in immediate failure.
However, reliability will be reduced by exposure to sustained
voltages above rated.
Capacitance: The standard unit of capacitance is the
farad. For practical capacitors, it is usually expressed in
ESR
Figure 2
-6
-9
microfarads (10 farad), nanofarads (10 farad), or picofarads
-12
(10 farad). Standard measurement conditions are as
O
ESR
follows:
DF =
X
c
Class I (up to 1,000 pF):
1MHz and 1.2 VRMS
maximum.
δ
X
Ζ
c
Class I (over 1,000 pF):
1kHz and 1.2 VRMS
maximum.
1
2πfC
=
X
Class II:
Class III:
1 kHz and 1.0 0.2 VRMS.
1 kHz and 0.5 0.1 VRMS.
c
Like all other practical capacitors, multilayer ceramic
capacitors also have resistance and inductance. A simplified
schematic for the equivalent circuit is shown in Figure 1.
Other significant electrical characteristics resulting from
these additional properties are as follows:
Insulation Resistance: Insulation Resistance (IR) is the
DC resistance measured across the terminals of a capacitor,
represented by the parallel resistance (Rp) shown in Figure 1.
For a given dielectric type, electrode area increases with
capacitance, resulting in a decrease in the insulation resis-
tance. Consequently, insulation resistance is usually specified
as the “RC” (IR x C) product, in terms of ohm-farads or
megohm-microfarads. The insulation resistance for a specific
capacitance value is determined by dividing this product by
the capacitance. However, as the nominal capacitance values
become small, the insulation resistance calculated from the
RC product reaches values which are impractical.
Consequently, IR specifications usually include both a mini-
mum RC product and a maximum limit on the IR calculated
from that value. For example, a typical IR specification might
read “1,000 megohm-microfarads or 100 gigohms, whichever
is less.”
R
Figure 1
P
R
L
S
C
C = Capacitance
L = Inductance
R
R
= Equivalent Series Resistance (ESR)
= Insulation Resistance (IR)
S
P
Impedance: Since the parallel resistance (Rp) is nor-
mally very high, the total impedance of the capacitor is:
Insulation Resistance is the measure of a capacitor to
resist the flow of DC leakage current. It is sometimes referred
to as “leakage resistance.” The DC leakage current may be
calculated by dividing the applied voltage by the insulation
resistance (Ohm’s Law).
2
RS + (XC - XL)2
Z =
Dielectric Withstanding Voltage: Dielectric withstand-
ing voltage (DWV) is the peak voltage which a capacitor is
designed to withstand for short periods of time without dam-
age. All KEMET multilayer ceramic capacitors will withstand a
test voltage of 2.5 x the rated voltage for 60 seconds.
Where Z =Total Impedance
RS = Equivalent Series Resistance
1
XC = Capacitive Reactance =
2πfC
KEMET specification limits for these characteristics at
standard measurement conditions are shown in Table 1 on
page 4. Variations in these properties caused by changing
conditions of temperature, voltage, frequency, and time are
covered in the following sections.
XL = Inductive Reactance = 2πfL
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
5
APPLICATION NOTES FOR MULTILAYER
CERAMIC CAPACITORS
TABLE 1
EIA TEMPERATURE CHARACTERISTIC CODES
FOR CLASS I DIELECTRICS
Significant Figure
of Temperature
Coefficient
Multiplier Applied
to Temperature
Coefficient
Tolerance of
Temperature
Coefficient *
PPM per
Degree C
Letter
Symbol
Multi-
plier
Number
Symbol
PPM per
Degree C
Letter
Symbol
0.0
0.3
0.9
1.0
1.5
2.2
3.3
4.7
7.5
C
B
A
M
P
R
S
T
-1
-10
-100
-1000
-100000
+1
0
1
2
3
4
5
6
7
8
9
30
60
G
H
J
K
L
120
250
500
1000
2500
M
N
+10
+100
+1000
+10000
U
* These symetrical tolerances apply to a two-point measurement of
temperature coefficient: one at 25°C and one at 85°C. Some deviation
is permitted at lower temperatures. For example, the PPM tolerance
for C0G at -55°C is +30 / -72 PPM.
TABLE 2
EIA TEMPERATURE CHARACTERISTIC CODES
FOR CLASS II & III DIELECTRICS
Low Temperature
Rating
High Temperature Maximum Capacitance
Rating Shift
Degree
Celcius
Letter
Symbol Celcius
Degree
Number
Symbol
Letter
Symbol
Percent
+10C
-30C
-55C
Z
Y
X
+45C
+65C
+85C
+105C
+125C
+150C
+200C
2
4
5
6
7
8
9
1.0%
1.5%
2.2%
3.3%
4.7%
7.5%
10.0%
15.0%
22.0%
A
B
C
D
E
F
P
R
S
T
+10
+20
+30
+40
+50
+60
+70
+80
+22/-33%
+22/-56%
+22/-82%
U
V
6
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
APPLICATION NOTES FOR MULTILAYER
CERAMIC CAPACITORS
At higher AC voltages, both capacitance and dissipation factor
begin to decrease.
Typical curves showing the effect of applied AC and DC
voltage are shown in Figure 6 for KEMET X7R capacitors and
Figure 7 for KEMET Z5U capacitors.
Effect of Frequency: Frequency affects both capaci-
tance and dissipation factor. Typical curves for KEMET multi-
layer ceramic capacitors are shown in Figures 8 and 9.
T
he variation of impedance with frequency is an impor-
tant consideration in the application of multilayer ceramic
capacitors. Total impedance of the capacitor is the vector of the
capacitive reactance, the inductive reactance, and the ESR, as
illustrated in Figure 2. As frequency increases, the capacitive
reactance decreases. However, the series inductance (L)
shown in Figure 1 produces inductive reactance, which
increases with frequency. At some frequency, the impedance
ceases to be capacitive and becomes inductive. This point, at
the bottom of the V-shaped impedance versus frequency
curves, is the self-resonant frequency. At the self-resonant fre-
quency, the reactance is zero, and the impedance consists of
the ESR only.
Typical impedance versus frequency curves for KEMET
multilayer ceramic capacitors are shown in Figures 10, 11, and
12. These curves apply to KEMET capacitors in chip form, with-
out leads. Lead configuration and lead length have a significant
impact on the series inductance. The lead inductance is
approximately 10nH/inch, which is large compared to the
inductance of the chip. The effect of this additional inductance
is a decrease in the self-resonant frequency, and an increase
in impedance in the inductive region above the self-resonant
frequency.
Effect of Time: The capacitance of Class II and III
dielectrics change with time as well as with temperature, volt-
age and frequency. This change with time is known as “aging.”
It is caused by gradual realignment of the crystalline structure
of the ceramic dielectric material as it is cooled below its Curie
temperature, which produces a loss of capacitance with time.
The aging process is predictable and follows a logarithmic
decay. Typical aging rates for C0G, X7R, and Z5U dielectrics
are as follows:
C0G
X7R
Z5U
None
2.0% per decade of time
5.0% per decade of time
Typical aging curves for X7R and Z5U dielectrics are
shown in Figure 13.
Effect of Temperature: Both capacitance and dissipa-
tion factor are affected by variations in temperature. The max-
imum capacitance change with temperature is defined by the
temperature characteristic. However, this only defines a “box”
bounded by the upper and lower operating temperatures and
the minimum and maximum capacitance values. Within this
“box”, the variation with temperature depends upon the spe-
cific dielectric formulation. Typical curves for KEMET capaci-
tors are shown in Figures 3, 4, and 5. These figures also
include the typical change in dissipation factor for KEMET
capacitors.
The aging process is reversible. If the capacitor is heat-
ed to a temperature above its Curie point for some period of
time, de-aging will occur and the capacitor will regain the
capacitance lost during the aging process. The amount of de-
aging depends on both the elevated temperature and the
length of time at that temperature. Exposure to 150°C for one-
half hour or 125°C for two hours is usually sufficient to return
the capacitor to its initial value.
Because the capacitance changes rapidly immediately
after de-aging, capacitance measurements are usually delayed
for at least 10 hours after the de-aging process, which is often
referred to as the “last heat.” In addition, manufacturers utilize
the aging rates to set factory test limits which will bring the
capacitance within the specified tolerance at some future time,
to allow for customer receipt and use. Typically, the test limits
are adjusted so that the capacitance will be within the specified
tolerance after either 1,000 hours or 100 days, depending on
the manufacturer and the product type.
Insulation resistance decreases with temperature.
Typically, the insulation resistance at maximum rated temper-
ature is 10% of the 25°C value.
Effect of Voltage: Class I ceramic capacitors are not
affected by variations in applied AC or DC voltages. For Class
II and III ceramic capacitors, variations in voltage affect only
the capacitance and dissipation factor. The application of DC
voltage higher than 5 vdc reduces both the capacitance and
dissipation factor. The application of AC voltages up to 10-20
Vac tends to increase both capacitance and dissipation factor.
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
7
APPLICATION NOTES FOR MULTILAYER
CERAMIC CAPACITORS
capacitors may be operated with AC voltage applied without
need for DC bias.
POWER DISSIPATION
Power dissipation has been empirically determined for
two representative KEMET series: C052 and C062. Power dis-
sipation capability for various mounting configurations is shown
in Table 3. This table was extracted from Engineering Bulletin
F-2013, which provides a more detailed treatment of this sub-
ject.
Note that no significant difference was detected between
the two sizes in spite of a 2 to 1 surface area ratio. Due to the
materials used in the construction of multilayer ceramic capac-
itors, the power dissipation capability does not depend greatly
on the surface area of the capacitor body, but rather on how
well heat is conducted out of the capacitor lead wires.
Consequently, this power dissipation capability is applicable to
other leaded multilayer styles and sizes.
RELIABILITY
A well constructed multilayer ceramic capacitor is
extremely reliable and, for all practical purposes, has an infi-
nite life span when used within the maximum voltage and
temperature ratings. Capacitor failure may be induced by sus-
tained operation at voltages that exceed the rated DC voltage,
voltage spikes or transients that exceed the dielectric with-
standing voltage, sustained operation at temperatures above
the maximum rated temperature, or the excessive tempera-
ture rise due to power dissipation.
Failure rate is usually expressed in terms of percent per
1,000 hours or in FITS (failure per billion hours). Some
KEMET series are qualified under U.S. military established
reliability specifications MIL-PRF-20, MIL-PRF-123, MIL-
PRF-39014, and MIL-PRF-55681. Failure rates as low as
0.001% per 1,000 hours are available for all capacitance /
voltage ratings covered by these specifications. These spec-
ifications and accompanying Qualified Products List should
be consulted for details.
TABLE 3
POWER DISSIPATION CAPABILITY
(Rise in Celsius degrees per Watt)
Power
Dissipation
Mounting Configuration
For series not covered by these military specifications,
an internal testing program is maintained by KEMET Quality
Assurance. Samples from each week’s production are sub-
jected to a 2,000 hour accelerated life test at 2 x rated voltage
and maximum rated temperature. Based on the results of
these tests, the average failure rate for all non-military series
covered by this test program is currently 0.06% per 1,000
hours at maximum rated conditions. The failure rate would be
much lower at typical use conditions. For example, using MIL-
HDBK-217D this failure rate translates to 0.9 FITS at 50%
rated voltage and 50°C.
of C052 & C062
1.00" leadwires attached to binding post
of GR-1615 bridge (excellent heat sink)
90 Celsius degrees
rise per Watt 10%
0.25" leadwires attached to binding post
of GR-1615 bridge
55 Celsius degrees
rise per Watt 10%
Capacitor mounted flush to 0.062" glass-
epoxy circuit board with small copper traces
77 Celsius degrees
rise per Watt 10%
Capacitor mounted flush to 0.062" glass-
epoxy circuit board with four square inches
of copper land area as a heat sink
53 Celsius degrees
rise per Watt 10%
Current failure rate details for specific KEMET multilay-
er ceramic capacitor series are available on request.
As shown in Table 3, the power dissipation capability of
the capacitor is very sensitive to the details of its use environ-
ment. The temperature rise due to power dissipation should not
exceed 20°C. Using that constraint, the maximum permissible
power dissipation may be calculated from the data provided in
Table 3.
It is often convenient to translate power dissipation capa-
bility into a permissible AC voltage rating. Assuming a sinu-
soidal wave form, the RMS “ripple voltage” may be calculated
from the following formula:
MISAPPLICATION
Ceramic capacitors, like any other capacitors, may fail
if they are misapplied. Typical misapplications include expo-
sure to excessive voltage, current or temperature. If the
dielectric layer of the capacitor is damaged by misapplication
the electrical energy of the circuit can be released as heat,
which may damage the circuit board and other components
as well.
If potential for misapplication exists, it is recommended
that precautions be taken to protect personnel and equipment
during initial application of voltage. Commonly used precau-
tions include shielding of personnel and sensing for excessive
power drain during board testing.
PMAX
E = Z x
R
Where E = RMS Ripple Voltage (volts)
P = Power Dissipation (watts)
Z = Impedance
STORAGE AND HANDLING
Ceramic chip capacitors should be stored in normal
working environments. While the chips themselves are quite
robust in other environments, solderability will be degraded
by exposure to high temperatures, high humidity, corrosive
atmospheres, and long term storage. In addition, packaging
materials will be degraded by high temperature – reels may
soften or warp, and tape peel force may increase. KEMET
recommends that maximum storage temperature not exceed
40˚ C, and maximum storage humidity not exceed 70% rela-
tive humidity. In addition, temperature fluctuations should be
minimized to avoid condensation on the parts, and atmos-
pheres should be free of chlorine and sulfur bearing com-
pounds. For optimized solderability, chip stock should be
used promptly, preferably within 1.5 years of receipt.
R = ESR
The data necessary to make this calculation is included in
Engineering Bulletin F-2013. However, the following criteria
must be observed:
1. The temperature rise due to power dissipation
should be limited to 20°C.
2. The peak AC voltage plus the DC voltage must not
exceed the maximum working voltage of the
capacitor.
Provided that these criteria are met, multilayer ceramic
8
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
APPLICATION NOTES FOR MULTILAYER
CERAMIC CAPACITORS
EFFECT OF FREQUENCY
IMPEDANCE VS FREQUENCY
+0.2
+0.1
0
0.20
0.10
0.0
%ΔC
100
-0.1
-0.2
%DF
10
100
1K
10K
100K
1M
10M
0.001µF
1
Figure 8.
Frequency - Hertz
Capacitance & DF vs Frequency - C0G
0.01µF
0.1
0.010.1
1
1
0
100
1000
Frequency - MHz
Figure 10. Impedance vs Frequency
+5
0
10.0
7.5
5.0
2.5
0.0
for C0G Dielectric
%DF
%ΔC
-5
-10
-15
100
100
1K
10K
100K
1M
10M
0.01µF
Figure 9.
Frequency - Hertz
10
Capacitance & DF vs Frequency - X7R & Z5U
0.1µ
F
1
1.0µF
0.1
0.01
0.1
1
1 0
100
1000
Frequency -MHz
Figure 11. Impedance vs Frequency
(hours)
EFFECT OF TIME
for X7R Dielectric
100%
98%
X7R
96%
94%
92%
90%
88%
100
86%
84%
10
Z5U
82%
80%
0.1µF
1
78%
1.0µF
76%
0.1
74%
1
1
0
1
0
0
1
0
0
0
1
0
K
0K
10
0.01
Figure 13. Typical Aging Rates for X7R & Z5U
0.1
1
1
0
100
1000
Frequency -MHz
Figure 12. Impedance vs Frequency
for Z5U Dielectric
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
9
CERAMIC CONFORMALLY COATED/AXIAL
“AXIMAX”
ENVIRONMENTAL
GENERAL SPECIFICATIONS
Working Voltage:
Vibration:
EIA RS-198, Method 304, Condition D (10-2000Hz; 20g)
Shock:
EIA RS-198, Method 305, Condition I (100g)
Axial (WVDC)
C0G
X7R
Z5U
50, 100, 200
25, 50, 100, 200, 250
50, 100
Life Test:
Radial (WVDC)
EIA RS-198, Method 201, Condition D.
C0G
X7R
Z5U
50, 100, 200, 500, 1k, 1.5k, 2k, 2.5k, 3k
25, 50, 100, 200, 250, 500, 1k, 1.5k, 2k, 2.5k, 3k
50, 100
<200V
C0G – 200% of rated voltage @ +125°C
X7R – 200% of rated voltage @ +125°C
Z5U – 200% of rated voltage @ +85°C
>500V
Temperature Characteristics:
C0G
X7R
Z5U
0
30 PPM / °C from -55°C to +125°C (1)
15% from -55°C to +125°C
C0G – rated voltage @ +125°C
X7R – rated voltage @ +125°C
+ 22%, -56% from +10°C to +85°C
Post Test Limits @ 25°C are:
Capacitance Change:
Capacitance Tolerance:
C0G
X7R
Z5U
0.5pF, 1%, 2%, 5%, 10%, 20%
C0G ( 200V) – 3% or 0.25pF, whichever is greater.
C0G ( 500V) – 3% or 0.50pF, whichever is greater.
X7R – 20% of initial value (2)
Z5U – 30% of initial value (2)
Dissipation Factor:
10%, 20%, +80% / -20%
20%, 80% / -20%
Construction:
Epoxy encapsulated – meets flame test requirements
of UL Standard 94V-0.
C0G – 0.10% maximum
X7R – 2.5% maximum (3.5% for 25V)
Z5U – 4.0% maximum
High-temperature solder – meets EIA RS-198, Method 302,
Condition B (260°C for 10 seconds)
Insulation Resistance:
C0G – 10 G or 100 M
–
F, whichever is less.
Lead Material:
Standard: 100% matte tin (Sn) with nickel (Ni) underplate
and steel core ( “TA” designation).
>1kV tested @ 500V.
X7R – 10 G or 100 M
–
F, whichever is less.
Alternative 1: 60% Tin (Sn)/40% Lead (Pb) finish with copper-
clad steel core ( “HA” designation).
>1kV tested @ 500V.
Z5U – 1 G or 100 M
– F, whichever is less.
Alternative 2: 60% Tin (Sn)/40% Lead (Pb) finish with 100%
copper core (available with “HA” termination code with c-spec)
Moisture Resistance:
EIA RS-198, Method 204, Condition A (10 cycles
without applied voltage).
Solderability:
EIA RS-198, Method 301, Solder Temperature: 230°C 5°C.
Post Test Limits @ 25°C are:
Capacitance Change:
Dwell time in solder = 7
seconds.
C0G ( 200V) – 3% or 0.25pF, whichever is greater.
C0G ( 500V) – 3% or 0.50pF, whichever is greater.
X7R – 20% of initial value (2)
Z5U – 30% of initial value (2)
Dissipation Factor:
Terminal Strength:
EIA RS-198, Method 303, Condition A (2.2kg)
ELECTRICAL
Capacitance @ 25°C:
C0G – 0.10% maximum
Within specified tolerance and following test conditions.
C0G – >1000pF with 1.0 vrms @ 1 kHz
1000pF with 1.0 vrms @ 1 MHz
X7R – 2.5% maximum (3.5% for 25V)
Z5U – 4.0% maximum
Insulation Resistance:
C0G – 10 G or 100 M
– Fwhichever is less.
X7R – with 1.0 vrms @ 1 kHz (Referee Time: 1,000 hours)
Z5U – with 1.0 vrms @ 1 kHz
500V test @ rated voltage, >500V test @ 500V.
X7R – 10 G or 100 M F, whichever is less.
500V test @ rated voltage, >500V test @ 500V.
–
Dissipation Factor @25°C:
Same test conditions as capacitance.
C0G – 0.10% maximum
X7R – 2.5% maximum (3.5% for 25V)
Z5U – 4.0% maximum
Z5U – 1k M or 100 M
– F, whichever is less.
Thermal Shock:
EIA RS-198, Method 202, Condition B (C0G & X7R:
-55°C to 125°C); Condition A (Z5U: -55°C to 85°C)
Insulation Resistance @25°C:
EIA RS-198, Method 104, Condition A <1kV
C0G – 100 G or 1000 M
– F, whichever is less.
(1) +53 PPM -30 PPM/ °C from +25°C to -55°C, + 60 PPM below 10pF.
(2) X7R and Z5U dielectrics exhibit aging characteristics; therefore, it is highly
recommended that capacitors be deaged for 2 hours at 150°C and stabilized
at room temperature for 48 hours before capacitance measurements are made.
500V test @ rated voltage, >500V test @ 500V
X7R – 100 G or 1000 M
F, whichever is less.
500V test @ rated voltage, >500V test @ 500V
Z5U – 10 G or 1000 M F, whichever is less.
–
–
Dielectric Withstanding Voltage:
EIA RS-198, Method 103
250V test @ 250% of rated voltage for 5 seconds
with current limited to 50mA.
500V test @ 150% of rated voltage for 5 seconds
with current limited to 50mA.
1000V test @ 120% of rated voltage for 5 seconds
with current limited to 50mA.
10
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
CERAMIC CONFORMALLY COATED/RADIAL
“STANDARD & HIGH VOLTAGE GOLD MAX”
STANDARD LEAD CONFIGURATION OUTLINE DRAWINGS
(1)
(1)
Drawings are not to scale. See table below for dimensions. See page 16 for optional lead configurations.
(1) Lead configuration depends on capacitance value. (2) H dimensions does not include meniscus.
DIMENSIONS INCHES (MILLIMETERS)
LD
+.004(.10)
-.001(.025)
Case
Size
L
Max.
H.
Max.
Standard
T Max.
High Voltage
T Max.
S(1)
.030 (.78)
LL
Min.
C315
C317
C320
C322
C323
C330
C333
C340
C350
0.150 (3.81)
0.150 (3.81)
0.200 (5.08)
0.200 (5.08)
0.200 (5.08)
0.300 (7.62)
0.300 (7.62)
0.400 (10.16)
0.500 (12.70)
0.210 (5.33)
0.230 (5.84)
0.260 (6.60)
0.260 (6.60)
0.320 (8.13)
0.360 (9.14)
0.390 (9.91)
0.460 (11.68)
0.560 (14.22)
0.100 (2.54)
0.100 (2.54)
0.125 (3.18)(2)
0.125 (3.18)
0.125 (3.18)
0.150 (3.81)
0.150 (3.81)
0.150 (3.81)
0.200 (5.08)
0.150 (3.81)
0.150 (3.81)
0.200 (5.08)
0.200 (5.08)
0.200 (5.08)
0.250 (6.35)
0.250 (6.35)
0.270 (6.86)
0.270 (6.86)
0.100 (2.54)
0.200 (5.08)
0.100 (2.54)
0.200 (5.08)
0.200 (5.08)
0.200 (5.08)
0.200 (5.08)
0.200 (5.08)
0.400 (10.16)
0.020 (.51)
0.020 (.51)
0.020 (.51)
0.020 (.51)
0.020 (.51)
0.020 (.51)
0.020 (.51)
0.020 (.51)
0.025 (.64)
0.276 (7.00)
0.276 (7.00)
0.276 (7.00)
0.276 (7.00)
0.276 (7.00)
0.276 (7.00)
0.276 (7.00)
0.276 (7.00)
0.276 (7.00)
Note: 1 inch = 25.4mm.
Note (1): Measured at seating plane.
Note (2): Thickness = 0.16" (4.064mm) for C320 from 4.7 - 10.0 F.
ORDERING INFORMATION
C 320 C 102 M
1
R
5
T
A
FAILURE RATE
CERAMIC
CASE SIZE
A – Not Applicable
LEAD MATERIAL
See Table Above
T – 100ꢃ Tin (Sn)
SPECIFICATION
H – 60/40ꢃ Tin/Lead (Sn;b)
INTERNAL CONSTRUCTION
ꢀ – ꢅultilayer
C – Standard
CAPACITANCE PICOFARAD CODE
Expressed in picofarads (pF). First two
digits represent significant figures. Third
digit specifies number of zeros. Use 9 for
1.0 thru 9.9 pF. Example 2.2pF = 229
DIELECTRIC
EIA ꢂesignation
G – C0G (N;0) - Ultra Stable
R – X7R - Stable
U – ZꢀU - General ;urpose
CAPACITANCE TOLERANCE
C0G: C – 0.2ꢀpFꢁ ꢂ – 0.ꢀpFꢁ F – 1ꢃꢁ
G – 2ꢃꢁ ꢄ – ꢀꢃ5
RATED VOLTAGE (DC)
3 – 2ꢀ
ꢀ – ꢀ0
1 – 100
2 – 200
A – 2ꢀ0
C – ꢀ00
ꢂ – 1000
F – 1ꢀ00
G – 2000
Z – 2ꢀ00
H – 3000
X7R: K – 10ꢃꢁ ꢅ – 20ꢃꢁ ; – 05 -100ꢃꢁ
Z – -205+80ꢃ
Z5U: ꢅ – 20ꢃꢁ ; – 05 -100ꢃꢁ Z – -205+80ꢃ
For packaging information, see pages 47 and 48.
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
15
CERAMIC CONFORMALLY COATED/RADIAL
“STANDARD & HIGH VOLTAGE GOLD MAX”
OPTIONAL CONFIGURATIONS BY LEAD SPACING
The preferred lead wire configurations are shown on page 15. However, additional configurations are
available. All available options, including those on page 15, are shown below grouped by lead spacing.
C 3 1 5
C 3 1 6
C 3 2 0
C 3 2 4
C 3 2 6
.150
MAX.
.150
MAX.
.200
MAX.
.200
MAX.
.200
MAX.
Lead Spacing
.100" .030
.210
MAX.
.260
MAX.
.260
MAX.
.230
MAX.
.350
MAX.
.276
MIN.
.276
MIN.
.276
MIN.
.230
.030
.230
.030
.100
.200
.100
.200
.100
.125
.100
.100
C 3 1 7
C 3 1 8
C 3 2 2
C 3 2 3
.200
MAX.
.150
MAX.
.150
MAX.
.200
MAX.
Lead Spacing
.200" .030
.260
MAX.
.320
MAX.
.230
MAX.
.235
MAX.
.276
MIN.
.276
MIN.
.276
MIN.
.276
MIN.
.200
.200
.200
.200
C 3 2 5
C 3 2 7
C 3 2 8
.200
MAX.
.200
MAX.
.200
MAX.
Lead Spacing
.200" .030
.320
MAX.
.325
MAX.
.350
MAX.
.276
MIN.
.276
MIN.
.230
.030
.200
.270
.200
.200
C 3 3 0
C 3 3 3
C 3 3 5
C 3 3 6
C 3 4 0
C 3 4 6
Lead Spacing
.200" .030
Note: C330 configuration
depends on capacitance.
See part number tables
for specifics.
.300
MAX.
.300
MAX.
.300
MAX.
.400
MAX.
.400
MAX.
.460
MAX.
.450
.590
MAX.
.420
.390
MAX.
MAX.
MAX.
.276
MIN.
.276
MIN.
.230
.030
.230
.030
.276
MIN.
.200
.300
.200
.320
.200
.200
.200
C 3 2 1
C 3 3 1
C 3 5 0
C 3 5 6
Lead Spacing
.250" .030
(Available in
bulk only)
.200
MAX.
.300
MAX.
Lead Spacing
.400" .030
.500
MAX.
.500
MAX.
.360
.560
.670
MAX.
.260
MAX.
MAX.
MAX.
.276
MIN.
.276
MIN.
.276
MIN.
.230
.030
.400
.520
.250
.250
.400
Note: Non-standard lead lengths are available in bulk only.
16
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
CERAMIC CONFORMALLY COATED/RADIAL
“STANDARD & HIGH VOLTAGE GOLD MAX”
CAPACITOR MARKINGS
Rated Voltage
Dielectric
Manufacturer
(KEMET)
Manufacturer
(KEMET)
Manufacturer
(KEMET)
Capacitance
Tolerance
KX7R
105K
100V
0814
Front
K1K
Back
102
K5U
104M
Dielectric
Capacitance
& Tolerance
Rated Voltage
Rated
Voltage
Capacitance
Code
Date Code
Capacitance
Tolerance
Capacitance
Code
C31X & C32X Size
C33X Size
C340 & C350 Size
RATINGS & PART NUMBER REFERENCE: ULTRA-STABLE TEMPERATURE CHARACTERISTICS — C0G/NP0
Style
C31X
C32X
C33X
C34X
C35X
WVDC
WVDC
WVDC
WVDC
WVDC
Cap Cap
Code Tol
Cap
50 100 200
500
1k
50 100 200
500
1k 1.5k 2k 50 100 200
500
1k 1.5k 2k 2.5k 3k 50 100 200
500
1k 2k 3k 50 100 200 500
1k 2k 3k
1.0pF
1.1
1.2
1.3
1.5
1.6
1.8
2.0
2.2
2.4
2.7
3.0
3.3
3.6
3.9
4.3
4.7
5.1
5.6
6.2
6.8
7.5
8.2
9.1
10
109
119
129
139
159
169
189
209
229
249
279
309
339
369
399
439
479
519
569
629
689
759
829
919
100
110
120
130
150
160
180
200
220
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
J,K
J,K
J,K
J,K
J,K
J,K
J,K
J,K
J,K
11
12
13
15
16
18
20
22
24
27
30
33
36
39
43
47
240 G,J,K
270 G,J,K
300 G,J,K
330 G,J,K
360 G,J,K
390 G,J,K
430 G,J,K
470 G,J,K
510 G,J,K
51
56
62
68
75
82
91
560
620
680
750
820
910
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
For packaging information, see pages 47 and 48.
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
17
CERAMIC CONFORMALLY COATED/RADIAL
“STANDARD & HIGH VOLTAGE GOLD MAX”
RATINGS & PART NUMBER REFERENCE:
ULTRA-STABLE TEMPERATURE CHARACTERISTICS
— C0G/NPO CONT.
Style
C31X
WVDC
C32X
WVDC
C34X
WVDC
C35X
WVDC
C33X
WVDC
Cap Cap
Code Tol
Cap
50 100 200
500
1k
50 100 200
500
1k 1.5k 2k 50 100 200
500
1k 1.5k 2k 2.5k 3k 50 100 200
500
1k 2k 3k 50 100 200 500
1k 2k 3k
100
110
120
130
150
160
180
200
220
240
270
300
330
360
390
430
470
510
560
620
680
750
820
910
1000
1100
1200
1300
1500
1600
1800
2000
2200
2400
2700
3000
3300
3600
3900
4300
4700
5100
5600
6200
6800
7500
8200
9100
101
111
121
131
151
161
181
201
221
241
271
301
331
361
391
431
471
511
561
621
681
751
821
911
102
112
122
132
152
162
182
202
222
242
272
302
332
362
392
432
472
512
562
622
682
752
822
912
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
F,G,J
.010uF 103
.015
.015
.018
.022
.027
.033
.039
.047
.056
.068
.082
.10
123
153
183
223
273
333
393
473
563
683
823
104
124
.12
For packaging information, see pages 47 and 48.
18
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
CERAMIC CONFORMALLY COATED/RADIAL
“STANDARD & HIGH VOLTAGE GOLD MAX”
RATINGS & PART NUMBER REFERENCE: STABLE TEMPERATURE CHARACTERISTICS - X7R
Style
Cap
C31X
C32X
C33X
WVDC
WVDC
WVDC
Cap
25 50 100 200 250 500 1k 25 50
100 200 250 500 1k 1.5k 2k 25 50
100
200
250
500 1k 1.5k 2k 2.5k 3k
Cap
10pF
12
15
18
22
27
33
39
47
56
68
82
Code
100
120
150
180
220
270
330
390
470
560
680
820
101
121
151
181
221
271
331
391
471
561
681
821
102
122
152
182
222
272
332
392
472
562
682
822
103
123
153
183
223
273
333
393
473
563
683
823
104
124
154
184
224
274
334
394
474
564
684
824
105
125
155
185
225
275
335
395
475
565
685
106
Tol
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
100
120
150
180
220
270
330
390
470
560
680
820
1000
1200
1500
1800
2200
2700
3300
3900
4700
5600
6800
8200
.010uF
.012
.015
.018
.022
.027
.033
.039
.047
.056
.068
.082
.10
.12
.15
.18
.22
.27
.33
.39
.47
.56
.68
.82
1.0
1.2
1.5
1.8
2.2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2.7
3.3
3.9
4.7
5.6
6.8
10.0
1
1
1
1
1
(1) Thickness max = 0.160" (4.064mm)
(2) Requires straight leads (all other C33X's require bent leads)
For packaging information, see pages 47 and 48.
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
19
CERAMIC CONFORMALLY COATED/RADIAL
“STANDARD & HIGH VOLTAGE GOLD MAX”
RATINGS & PART NUMBER REFERENCE: STABLE TEMPERATURE CHARACTERISTICS - X7R
Style
C34X
C35X
WVDC
WVDC
Cap
Cap
Tol
25
50
100
200
250
500
1k
1.5k
2k
2.5k
3k
25
50
100
200
250
500
1k
2k
3k
Cap Code
10pF
12
15
18
22
27
33
39
47
100
120
150
180
220
270
330
390
470
560
680
820
101
121
151
181
221
271
331
391
471
561
681
821
102
122
152
182
222
272
332
392
472
562
682
822
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
K,M,P,Z
56
68
82
100
120
150
180
220
270
330
390
470
560
680
820
1000
1200
1500
1800
2200
2700
3300
3900
4700
5600
6800
8200
.010uF 103
.012
.015
.018
.022
.027
.033
.039
.047
.056
.068
.082
.10
.12
.15
.18
.22
.27
.33
.39
.47
.56
.68
.82
1.0
1.2
1.5
1.8
2.2
2.7
3.3
3.9
4.7
5.6
6.8
10
123
153
183
223
273
333
393
473
563
683
823
104
124
154
184
224
274
334
394
474
564
684
824
105
125
155
185
225
275
335
395
475
565
685
106
(1) Thickness max = 0.160" (4.06mm)
(2) Requires straight leads (all other C33X's require bent leads)
For packaging information, see pages 47 and 48.
20
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
CERAMIC CONFORMALLY COATED/RADIAL
“STANDARD & HIGH VOLTAGE GOLD MAX”
RATINGS & PART NUMBER REFERENCE
GENERAL PURPOSE TEMPERATURE CHARACTERISTIC — Z5U
Style
C31X
WVDC
C32X
WVDC
C33X
WVDC
C34X
WVDC
C35X
WVDC
Cap
Code
Cap
Tol
Cap
50
100
200
50
100
200
50
100
200
50
100
200
50
100
200
1000pF
1200
1500
1800
2200
2700
3300
3900
4700
5600
6800
8200
.010uF
.012
.015
.018
.022
.027
.033
.039
.047
.056
.068
.082
.10
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
M,P,Z
102
122
152
182
222
272
332
392
472
562
682
822
103
123
153
183
223
273
333
393
473
563
683
823
104
124
154
184
224
274
334
394
474
564
684
824
105
125
155
185
225
275
335
395
475
565
685
.12
.15
.18
1
1
1
1
1
1
.22
.27
.33
.39
1
1
1
1
1
1
.47
.56
.68
.82
1.0
1.2
1
1
1
1
1.5
1.8
2.2
2.7
3.3
3.9
4.7
5.6
6.8
1
Requires straight leads (all other C33x's require bent leads)
For packaging information, see pages 47 and 48.
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
21
CERAMIC LEADED
PACKAGING INFORMATION
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
47
CERAMIC LEADED
PACKAGING INFORMATION
CERAMIC PACKAGING
Standard (1)
Bulk
Quantity
Ammo Pack
Maximum
Reel
Quantity
KEMET
Series
Military
Style
Military
Specification
Reel
Size
Quantity
Maximum
C114C-K-G
C124C-K-G
C192C-K-G
C202C-K
C222C-K
C052C-K-G
C062C-K-G
C114G
C124G
C192G
C202G
C222G
C052/56G
C062/66G
C512G
C522G
C114T
C124T
C192T
C202T
C222T
C052/56T
C062/66T
C31X
C32X
C33X
C340
C350
C410
C412
C420
C430
C440
C512
C522
C617
CK12, CC75
CK13, CC76
CK14, CC77
CK15
MIL-C-11015/
MIL-PRF-20
200/Box
200/Box
100/Box
25/Box
5000
5000
3000
500
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
N/A
N/A
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
CK16
10/Tray
300
CK05, CC05
CK06, CC06
CCR75
CCR76
CCR77
CC78-CCR78
CC79-CCR79
CCR05
100/Bag
100/Bag
200/Box
200/Box
100/Box
25/Box
2000
1500
2000
1500
5000
5000
3000
500
MIL-PRF-20
10/Tray
300
100/Bag
100/Bag
Footnote (2)
Footnote (2)
200/Box
200/Box
100/Box
25/Box
1700
1500
N/A
CCR06
CC07-CCR07
CC08-CCR08
CKR11
CKR12
CKR14
CKR15
CKR16
CKR05
CKR06
N/A
MIL-PRF-39014
5000
5000
3000
500
10/Tray
300
100/Bag
100/Bag
500/Bag
500/Bag
250/Bag
100/Bag
50/Bag
300/Box
200/Box
300/Box
200/Box
200/Box
Footnote (2)
Footnote (2)
250/Bag
100/Bag
100/Bag
100/Bag
50/Bag
1700
1500
2500
2500
1500
1000
500
5000
5000
5000
2500
2500
N/A
N/A
1000
500
500
500
500
500
500
500
2500
2500
1500
1000
N/A
4000
4000
4000
2000
2000
12"
N/A
N/A
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
N/A
N/A
N/A
N/A
C622/C623
C627/C628
C630/C631
C637/C638
C640/C641
C642/C643
C647/C648
C657/C658
C667/C668
50/Bag
50/Bag
50/Bag
50/Bag
500
500
50/Bag
NOTE: (1) Standard packaging refers to number of pieces per bag, tray or vial.
(2) Quantity varies. For further details, please consult the factory.
48
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
相关型号:
C340C474Z5R5TA
Ceramic Capacitor, Multilayer, Ceramic, 50V, 80% +Tol, 20% -Tol, X7R, 15% TC, 0.47uF, Through Hole Mount, 4015, RADIAL LEADED
KEMET
C340C474ZAR5TA7301
Ceramic Capacitor, Ceramic, 250V, 80% +Tol, 20% -Tol, X7R, -/+15ppm/Cel TC, 0.47uF, 4015,
KEMET
C340C475K5R5TA
Ceramic Capacitor, Multilayer, Ceramic, 50V, 10% +Tol, 10% -Tol, X7R, 15% TC, 4.7uF, Through Hole Mount, 4015, RADIAL LEADED
KEMET
C340C475M5R5TA
Ceramic Capacitor, Multilayer, Ceramic, 50V, 20% +Tol, 20% -Tol, X7R, 15% TC, 4.7uF, Through Hole Mount, 4015, RADIAL LEADED
KEMET
C340C475P5R5TA7301
Ceramic Capacitor, Ceramic, 50V, 0% +Tol, 100% -Tol, X7R, -/+15ppm/Cel TC, 4.7uF, 4015,
KEMET
C340C475P5U5TA7303
Ceramic Capacitor, Ceramic, 50V, 0% +Tol, 100% -Tol, Z5U, -56/+22% TC, 4.7uF, 4015,
KEMET
C340C475Z5U5TA
Ceramic Capacitor, Multilayer, Ceramic, 50V, 80% +Tol, 20% -Tol, Z5U, -56/+22% TC, 4.7uF, Through Hole Mount, 4015, RADIAL LEADED
KEMET
C340C510FCG5TA
Ceramic Capacitor, Multilayer, Ceramic, 500V, 1% +Tol, 1% -Tol, C0G, 30ppm/Cel TC, 0.000051uF, Through Hole Mount, RADIAL LEADED
KEMET
C340C510FDG5TA
Ceramic Capacitor, Multilayer, Ceramic, 1000V, 1% +Tol, 1% -Tol, C0G, 30ppm/Cel TC, 0.000051uF, Through Hole Mount, RADIAL LEADED
KEMET
C340C510GDG5TA
Ceramic Capacitor, Multilayer, Ceramic, 1000V, 2% +Tol, 2% -Tol, C0G, 30ppm/Cel TC, 0.000051uF, Through Hole Mount, 4027, RADIAL LEADED
KEMET
C340C510JCG5TA
Ceramic Capacitor, Multilayer, Ceramic, 500V, 5% +Tol, 5% -Tol, C0G, 30ppm/Cel TC, 0.000051uF, Through Hole Mount, 4027, RADIAL LEADED
KEMET
C340C510JHG5TA
Ceramic Capacitor, Multilayer, Ceramic, 3000V, 5% +Tol, 5% -Tol, C0G, 30ppm/Cel TC, 0.000051uF, Through Hole Mount, 4027, RADIAL LEADED
KEMET
©2020 ICPDF网 联系我们和版权申明