C1210X563B3GACTU [KEMET]
Flexible Termination System (FT-CAP), C0G Dielectric, 10 - 250 VDC (Commercial & Automotive Grade);型号: | C1210X563B3GACTU |
厂家: | KEMET CORPORATION |
描述: | Flexible Termination System (FT-CAP), C0G Dielectric, 10 - 250 VDC (Commercial & Automotive Grade) |
文件: | 总21页 (文件大小:1500K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric,
10 – 250 VDC (Commercial & Automotive Grade)
Overview
KEMET’s Flexible Termination (FT-CAP) Multilayer Ceramic
Capacitor in C0G dielectric incorporates a unique, flexible
termination system that is integrated with KEMET’s standard
termination materials. A conductive silver epoxy is utilized
between the base metal and nickel barrier layers of KEMET’s
standard termination system in order to establish pliability
while maintaining terminal strength, solderability and electrical
performance. This technology was developed in order to
address the primary failure mode of MLCCs– flex cracks, which
are typically the result of excessive tensile and shear stresses
produced during board flexure and thermal cycling. Flexible
termination technology inhibits the transfer of board stress to the
rigid ceramic body, therefore mitigating flex cracks which can
result in low IR or short circuit failures.
Combined with the stability of C0G dielectric and designed to
accommodate all capacitance requirements, these flex-robust
devices are RoHS Compliant, offer up to 5 mm of flex-bend
capability and exhibit no change in capacitance with respect to
time and voltage. Capacitance change with reference to ambient
temperature is limited to ±30 ppm/ºC from −55°C to +125°C.
In addition to Commercial Grade, Automotive Grade devices
are available which meet the demanding Automotive Electronics
Council's AEC–Q200 qualification requirements.
Although this technology does not eliminate the potential
for mechanical damage that may propagate during extreme
environmental and handling conditions, it does provide superior
flex performance over standard termination systems. FT-CAP
complements KEMET’s Open Mode, Floating Electrode (FE-
CAP), Floating Electrode with Flexible Termination (FF-CAP),
and KEMET Power Solutions (KPS) product lines by providing a
complete portfolio of flex mitigation solutions.
Click image above for interactive 3D content
Open PDF in Adobe Reader for full functionality
Ordering Information
C
1206
X
J
3
G
A
563
C
TU
Case Size Specification/
Capacitance
Code (pF)
Capacitance Rated Voltage
Failure Rate/ Termination
Design
Ceramic
Dielectric
G = C0G
Packaging/Grade (C-Spec)
(L" x W")
Series
Tolerance1
(VDC)
Finish2
0603
0805
1206
1210
1812
1825
2220
2225
X = Flexible
Termination
Two significant
digits +
number of zeros.
Use 9 for 1.0 – 9.9 pF F = ±1%
Use 8 for 0.5 – .99 pF G = ±2%
e.g., 2.2 pF = 229
e.g., 0.5 pF = 508
B = ±0.10 pF 8 = 10
C = ±0.25 pF 4 = 16
D = ±0.5 pF 3 = 25
A = N/A
C = 100%
Matte Sn
L = SnPb
(5% Pb
See "Packaging C-Spec
Ordering Options Table"
below
5 = 50
1 = 100
2 = 200
A = 250
minimum)
J = ±5%
K = ±10%
M = ±20%
1 Additional capacitance tolerance offerings may be available. Contact KEMET for details.
2 Additional termination finish options may be available. Contact KEMET for details.
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016
1
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric, 10 – 250 VDC (Commercial & Automotive Grade)
Packaging C-Spec Ordering Options Table
Packaging/Grade
Packaging Type1
Ordering Code (C-Spec)
Bulk Bag/Unmarked
7" Reel/Unmarked
Not required (Blank)
TU
7411 (EIA 0603 and smaller case sizes)
7210 (EIA 0805 and larger case sizes)
13" Reel/Unmarked
7" Reel/Unmarked / 2 mm pitch2
13" Reel/Unmarked / 2 mm pitch2
7081
7082
1 Default packaging is “Bulk Bag”. An ordering code C-Spec is not required for “Bulk Bag” packaging.
1 The terms “Marked” and “Unmarked” pertain to laser marking option of capacitors. All packaging options labeled as “Unmarked” will contain capacitors that have
not been laser marked. The option to laser mark is not available on these devices. For more information see “Capacitor Marking”.
2 The 2 mm pitch option allows for double the packaging quantity of capacitors on a given reel size. This option is limited to EIA 0603 (1608 metric) case size
devices. For more information regarding 2 mm pitch option see “Tape & Reel Packaging Information”.
Benefits
• −55°C to +125°C operating temperature range
• Superior flex performance (up to 5 mm)
• Lead (Pb)-Free, RoHS and REACH compliant
• EIA 0603, 0805, 1206, 1210, 1812, 1825, 2220, and
2225 case sizes
• DC voltage ratings of 10 V, 16 V, 25 V, 50 V, 100 V,
200 V and 250 V
• Capacitance offerings ranging from 0.5 pF up to 0.47 μF
• Available capacitance tolerances of ±0.10pF, ±0.25 pF,
±0.5 pF, ±1%, ±2%, ±5%, ±10%, and ±20%
• No piezoelectric noise
• High ripple current capability
• Preferred capacitance solution at line frequencies and into the
MHz range
• No capacitance change with respect to applied rated DC voltage
• Negligible capacitance change with respect to temperature from
−55°C to +125°C
• Non-polar device, minimizing installation concerns
• 100% pure matte tin-plated termination finish allowing for
excellent solderability
• Commercial & Automotive (AEC–Q200) Grades available
• SnPb termination finish option available upon request
(5% Pb minimum)
• Extremely low ESR and ESL
• High thermal stability
Applications
Typical applications include critical timing, tuning, circuits requiring low loss, circuits with pulse, high current, decoupling, bypass,
filtering, transient voltage suppression and blocking, as well as energy storage in critical and safety relevant circuits without (integrated)
current limitation, including those subject to high levels of board flexure or temperature cycling.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016
2
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric, 10 – 250 VDC (Commercial & Automotive Grade)
Automotive C-Spec Information
KEMET Automotive Grade products meet or exceed the requirements outlined by the Automotive Electronics Council. Details regarding
test methods and conditions are referenced in document AEC–Q200, Stress Test Qualification for Passive Components. These
products are supported by a Product Change Notification (PCN) and Production Part Approval Process warrant (PPAP).
Automotive products offered through our distribution channel have been assigned an inclusive ordering code C-Spec, "AUTO". This
C-Spec was developed in order to better serve small and medium sized companies that prefer an automotive grade component without
the requirement to submit a customer Source Controlled Drawing (SCD) or specification for review by a KEMET engineering specialist.
This C-Spec is therefore not intended for use by KEMET’s OEM Automotive customers and are not granted the same “privileges” as
other automotive C-Specs. Customer PCN approval and PPAP request levels are limited (see details below).
Product Change Notification (PCN)
The KEMET Product Change Notification system is used to communicate primarily the following types of changes:
• Product/process changes that affect product form, fit , function, and /or reliability
• Changes in manufacturing site
• Product obsolescence
Customer Notification due to:
KEMET Automotive
C-Spec
Days prior to
implementation
Process/Product change
Obsolescence*
Yes
KEMET assigned1
Yes (with approval and
sign off)
180 days Minimum
AUTO
Yes (without approval)
Yes
90 days Minimum
1 KEMET assigned C-Specs require the submittal of a customer SCD or customer specification for review. For additional information contact KEMET.
Production Part Approval Process (PPAP)
The purpose of the Production Part Approval Process is:
• To ensure that supplier can meet the manufacturability and quality requirements for the purchased parts.
• To provide the evidence that all customer engineering design record and specification requirements are properly understood and
fulfilled by the manufacturing organization.
• To demonstrate that the established manufacturing process has the potential to produce the part
KEMET
Automotive
C-Spec
PPAP (Product Part Approval Process) Level
1
●
○
2
3
●
○
4
5
KEMET
●
●
●
assigned1
AUTO
1 KEMET assigned C-Specs require the submittal of a customer SCD or customer specification for review. For additional information contact KEMET.
● Part Number specific PPAP available
○ Product family PPAP only
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016
3
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric, 10 – 250 VDC (Commercial & Automotive Grade)
Dimensions – Millimeters (Inches)
L
W
T
B
S
EIA
Size
Code
Metric
Size
Code
S
L
W
Width
T
B
Mounting
Technique
Separation
Minimum
Length
Thickness
Bandwidth
0603
0805
1206
1210
1812
1825
2220
2225
1608
2012
3216
3225
4532
4564
5650
5664
1.60 (.064) ± 0.17 (.007) 0.80 (.032) ±0.15 (.006)
2.00 (.079) ± 0.30 (.012) 1.25 (.049) ± 0.30 (.012)
3.30 (.130) ± 0.40 (.016) 1.60 (.063) ± 0.35 (.013)
3.30 (.130) ± 0.40 (.016) 2.60 (.102) ± 0.30 (.012)
4.50 (.178) ± 0.40 (.016) 3.20 (.126) ± 0.30 (.012)
4.60 (.181) ± 0.40 (.016) 6.40 (.252) ± 0.40 (.016)
5.90 (.232) ± 0.75 (.030) 5.00 (.197) ± 0.40 (.016)
5.90 (.232) ± 0.75 (.030) 6.40 (.248) ± 0.40 (.016)
0.45 (.018) ± 0.15 (.006)
0.50 (0.02) ± 0.25 (.010)
0.60 (.024) ± 0.25 (.010)
0.60 (.024) ± 0.25 (.010)
0.70 (.028) ± 0.35 (.014)
0.70 (.028) ± 0.35 (.014)
0.70 (.028) ± 0.35 (.014)
0.70 (.028) ± 0.35 (.014)
0.58 (.023)
0.75 (.030)
Solder Wave
or
Solder Reflow
See Table 2 for
Thickness
N/A
Solder Reflow Only
Qualification/Certification
Commercial Grade products are subject to internal qualification. Details regarding test methods and conditions are referenced in
Table 4, Performance & Reliability.
Automotive Grade products meet or exceed the requirements outlined by the Automotive Electronics Council. Details regarding test
methods and conditions are referenced in document AEC–Q200, Stress Test Qualification for Passive Components. For additional
information regarding the Automotive Electronics Council and AEC–Q200, please visit their website at www.aecouncil.com.
Environmental Compliance
Lead (Pb)-Free, RoHS, and REACH compliant without exemptions (excluding SnPb termination finish option).
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016
4
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric, 10 – 250 VDC (Commercial & Automotive Grade)
Electrical Parameters/Characteristics
Item
Parameters/Characteristics
Operating Temperature Range
Capacitance Change with Reference to +25°C and 0 VDC Applied (TCC)
Aging Rate (Maximum % Capacitance Loss/Decade Hour)
−55°C to +125°C
±30 ppm/ºC
0%
250% of rated voltage
(5 ±1 seconds and charge/discharge not exceeding 50 mA)
1Dielectric Withstanding Voltage (DWV)
2Dissipation Factor (DF) Maximum Limit at 25ºC
0.1%
1,000 megohm microfarads or 100 GΩ
(Rated voltage applied for 120 ±5 seconds at 25°C)
3Insulation Resistance (IR) Limit at 25°C
1DWV is the voltage a capacitor can withstand (survive) for a short period of time. It exceeds the nominal and continuous working voltage of the capacitor.
2Capacitance and dissipation factor (DF) measured under the following conditions:
1 MHz ±100 kHz and 1.0 Vrms ±0.2 V if capacitance ≤ 1,000 pF
1 kHz ±50 Hz and 1.0 Vrms ±0.2 V if capacitance > 1,000 pF
3To obtain IR limit, divide MΩ-µF value by the capacitance and compare to GΩ limit. Select the lower of the two limits.
Capacitance and Dissipation Factor (DF) measured under the following conditions:
Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known as
Automatic Level Control (ALC). The ALC feature should be switched to "ON."
Post Environmental Limits
High Temperature Life, Biased Humidity, Moisture Resistance
Rated DC
Voltage
Capacitance
Value
Dissipation Factor
(Maximum %)
Capacitance
Shift
Insulation
Resistance
Dielectric
C0G
All
All
0.5
0.3% or ±0.25 pF 10% of Initial Limit
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016
5
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric, 10 – 250 VDC (Commercial & Automotive Grade)
Table 1A – Capacitance Range/Selection Waterfall (0603 – 1206 Case Sizes)
Case Size/Series
Voltage Code
C0603X
C0805X
C1206X
8
4
3
5
1
2
A
8
4
3
5
1
2
A
8
4
3
5
1
2
A
Cap
Code
Capacitance
Rated Voltage (VDC)
Product Availability and Chip Thickness Codes
See Table 2 for Chip Thickness Dimensions
Capacitance Tolerance
0.50 & 0.75 pF
1.0 - 9.1 pF*
10 - 91 pF*
100 pF
110 - 180 pF*
200 - 300 pF*
330 pF
508 & 758
109 - 919*
100 - 910*
101
111 - 181*
201 - 301*
331
361
391
431
471
511
561
621
681
751
821
911
102
112
122
132
152
162
182
202
222
242
272
302
332
362
392
432
472
512
562
622
682
752
822
912
103
123
153
183
223
273
333
393
473
B
B
C
C
D
D
CJ CJ CJ CJ CJ CJ CJ DR DR DR DR DR DR DR
CJ CJ CJ CJ CJ CJ CJ DR DR DR DR DR DR DR EQ EQ EQ EQ EQ EQ EQ
CJ CJ CJ CJ CJ CJ CJ DR DR DR DR DR DR DR EQ EQ EQ EQ EQ EQ EQ
CJ CJ CJ CJ CJ CJ CJ DR DR DR DR DR DR DR EQ EQ EQ EQ EQ EQ EQ
CJ CJ CJ CJ CJ CJ CJ DR DR DR DR DR DR DR EQ EQ EQ EQ EQ EQ EQ
CJ CJ CJ CJ CJ CJ CJ DR DR DR DR DR DR DR EQ EQ EQ EQ EQ EQ EQ
CJ CJ CJ CJ CJ CJ CJ DR DR DR DR DR DR DR EQ EQ EQ EQ EQ EQ EQ
CJ CJ CJ CJ CJ CJ CJ DR DR DR DR DR DR DR EQ EQ EQ EQ EQ EQ EQ
CJ CJ CJ CJ CJ CJ CJ DR DR DR DR DR DR DR EQ EQ EQ EQ EQ EQ EQ
CJ CJ CJ CJ CJ CJ CJ DR DR DR DR DR DR DR EQ EQ EQ EQ EQ EQ EQ
CJ CJ CJ CJ CJ CJ CJ DR DR DR DR DR DD DD EQ EQ EQ EQ EQ EQ EQ
CJ CJ CJ CJ CJ CJ CJ DR DR DR DR DR DR DR EQ EQ EQ EQ EQ EQ EQ
CJ CJ CJ CJ CJ CJ CJ DR DR DR DR DR DR DR EQ EQ EQ EQ EQ EQ EQ
CJ CJ CJ CJ CJ CJ CJ DR DR DR DR DR DR DR EQ EQ EQ EQ EQ EQ EQ
CJ CJ CJ CJ CJ CJ CJ DR DR DR DR DR DR DR EQ EQ EQ EQ EQ EQ EQ
CJ CJ CJ CJ CJ CJ CJ DR DR DR DR DR DR DR EQ EQ EQ EQ EQ EQ EQ
CJ CJ CJ CJ CJ CJ CJ DR DR DR DR DR DR DR EQ EQ EQ EQ EQ EQ EQ
CJ CJ CJ CJ CJ CJ CJ DR DR DR DR DD DD DD EQ EQ EQ EQ EQ EQ EQ
CJ CJ CJ CJ CJ CJ CJ DR DR DR DR DD DD DD EQ EQ EQ EQ EQ EQ EQ
CJ CJ CJ CJ CJ CH CH DR DR DR DR DR DR DR EQ EQ EQ EQ EQ EQ EQ
CJ CJ CJ CJ CJ CH CH DR DR DR DR DR DR DR EQ EQ EQ EQ EQ EQ EQ
CJ CJ CJ CJ CJ CH CH DD DD DD DD DD DR DR EQ EQ EQ EQ ER ER ER
CJ CJ CJ CJ CJ CH CH DD DD DD DD DD DR DR EQ EQ EQ EQ ES ER ER
CJ CJ CJ CJ CJ CH CH DD DD DD DD DD DR DR EQ EQ EQ EQ ES ES ES
CJ CJ CJ CJ CJ CH CH DD DD DD DD DD DR DR EQ EQ EQ EQ ES ES ES
CJ CJ CJ CJ CJ CH CH DR DR DR DR DR DR DR EQ EQ EQ EQ ES ES ES
CJ CJ CJ CJ CJ CH CH DR DR DR DR DR DR DR EQ EQ EQ EQ ET ET ET
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
360 pF
390 pF
430 pF
470 pF
510 pF
560 pF
620 pF
680 pF
750 pF
820 pF
910 pF
1,000 pF
1,100 pF
1,200 pF
1,300 pF
1,500 pF
1,600 pF
1,800 pF
2,000 pF
2,200 pF
2,400 pF
2,700 pF
3,000 pF
3,300 pF
3,600 pF
3,900 pF
4,300 pF
4,700 pF
5,100 pF
5,600 pF
6,200 pF
6,800 pF
7,500 pF
8,200 pF
9,100 pF
10,000 pF
12,000 pF
15,000 pF
18,000 pF
22,000 pF
27,000 pF
33,000 pF
39,000 pF
47,000 pF
56,000 pF
68,000 pF
82,000 pF
0.10 µF
CJ CJ CJ CJ CJ
CJ CJ CJ CJ CJ
CJ CJ CJ CJ CJ
CJ CJ CJ CJ CJ
CJ CJ CJ CJ CJ
CJ CJ CJ CJ CJ
CJ CJ CJ CJ CJ
CJ CJ CJ CJ CJ
CJ CJ CJ CJ
CJ CJ CJ CJ
CJ CJ CJ CJ
CJ CJ CJ CJ
CJ CJ CJ
DR DR DR DR DR DR DR EQ EQ EQ EQ ER ER ER
DR DR DR DR DR DR DR EQ EQ EQ EQ ER ER ER
DD DD DD DD DR DR DR ER ER ER ER ER EQ EQ
DD DD DD DD DR DR DR ER ER ER ER ET EQ EQ
DD DD DD DD DR DD DD ER ER ER ER ET EQ EQ
DS DS DS DS DR DD DD ER ER ER ER EF EQ EQ
DS DS DS DS DR DD DD ER ER ER ER ER EQ EQ
DS DS DS DS DR DD DD ER ER ER ER ER EQ EQ
DS DS DS DS DR DD DD ES ES ES ES ES EQ EQ
DR DR DR DR DR DD DD ES ES ES ES ES EQ EQ
DR DR DR DR DR DG DG EQ EQ EQ EQ EQ EQ EQ
DR DR DR DR DR DG DG EQ EQ EQ EQ EQ EQ EQ
DR DR DR DR DR DG DG EQ EQ EQ EQ EQ EQ EQ
DR DR DR DR DR DG DG ER ER ER ER EQ ER ER
CJ CJ CJ
CJ CJ CJ
CJ CJ CJ
CJ CJ CJ
CJ CJ CJ
DR DR DR DR DR
DR DR DR DR DD
DR DR DR DR DS
DR DR DR DD DG
DR DR DR DD
DD DD DD DF
DF DF DF
ER ER ER ER EQ ER ER
ES ES ES ES EQ ER ER
EQ EQ EQ EQ EQ ES ES
EQ EQ EQ EQ EQ EF EF
EQ EQ EQ EQ EQ EH EH
EQ EQ EQ EQ ER EH EH
EQ EQ EQ EQ ET
EQ EQ EQ EQ ET
ER ER ER ET EH
ER ER ER ET EH
ES ES ES EF
DG DG DG
DG DG DG
DG DG DG
563
683
823
104
EF EF EF EH
EH EH EH EH
EH EH EH
Rated Voltage (VDC)
Voltage Code
Cap
Code
Capacitance
8
4
3
5
1
2
A
8
4
3
5
1
2
A
8
4
3
5
1
2
A
Case Size/Series
C0603X
C0805X
C1206X
*Capacitance range Includes E24 decade values only. (i.e., 10, 11, 12, 13, 15, 16, 18, 20, 22, 24, 27, 30, 33, 36, 39, 43, 47, 51, 56, 62, 68, 75, 82 and 91)
These products are protected under US Patents 7,172,985 and 7,670,981, other patents pending, and any foreign counterparts.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016
6
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric, 10 – 250 VDC (Commercial & Automotive Grade)
Table 1B – Capacitance Range/Selection Waterfall (1210 – 2225 Case Sizes)
Case Size/Series
Voltage Code
C1210X
C1812X
C1825X
C2220X
C2225X
8
4
3
5
1
2
A
5
1
2
A
5
1
2
A
5
1
2
A
5
1
2
A
Cap
Code
Capacitance
Rated Voltage (VDC)
Product Availability and Chip Thickness Codes
See Table 2 for Chip Thickness Dimensions
Capacitance Tolerance
1.0 - 9.1 pF*
10 - 91 pF*
100 - 430 pF*
470 - 910 pF*
1,000 pF
1,100 pF
1,200 pF
1,300 pF
1,500 pF
1,600 pF
1,800 pF
2,000 pF
2,200 pF
2,400 pF
2,700 pF
3,000 pF
3,300 pF
3,600 pF
3,900 pF
4,300 pF
4,700 pF
5,100 pF
5,600 pF
6,200 pF
6,800 pF
7,500 pF
8,200 pF
9,100 pF
10,000 pF
12,000 pF
15,000 pF
18,000 pF
22,000 pF
27,000 pF
33,000 pF
39,000 pF
47,000 pF
56,000 pF
68,000 pF
82,000 pF
0.10 µF
109 - 919*
100 - 910*
101 - 431*
471 - 911*
102
112
122
132
152
162
182
202
222
242
272
302
332
362
392
432
472
512
562
622
682
752
822
912
103
123
153
183
223
273
333
393
473
563
683
823
104
124
154
184
224
274
334
394
474
B
C
D
FN FN FN FN FN FN FN
FN FN FN FN FN FN FN
FN FN FN FN FN FN FN
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
FN FN FN FN FN FN FN GB GB GB GB
FN FN FN FN FN FN FN GB GB GB GB
FN FN FN FN FN FN FN GB GB GB GB
FN FN FN FN FN FN FN GB GB GB GB
FN FN FN FN FN FQ FQ GB GB GB GB
FN FN FN FN FN FE FE GB GB GB GB
FN FN FN FN FN FE FE GB GB GB GB
FN FN FN FN FN FE FE GB GB GB GB
FN FN FN FN FQ FE FE GB GB GB GB
FN FN FN FN FQ FZ FZ GB GB GB GB
FN FN FN FN FQ FQ FQ
FN FN FN FN FQ FQ FQ GB GB GB GB
FN FN FN FN FQ FA FA
FN FN FN FN FA FA FA GB GB GB GB
FN FN FN FN FA FA FA
FN FN FN FN FA FA FA GB GB GB GB HB HB HB HB
FN FN FN FN FA FA FA
FA FA FA FA FZ FZ FZ GB GB GD GD HB HB HB HB
FN FN FN FN FZ FZ FZ
FN FN FN FN FZ FZ FZ GB GB GH GH HB HB HB HB
FN FN FN FN FZ FN FN
FN FN FN FN FZ FN FN GB GB GJ GJ HB HB HB HB JE JE JB
FQ FQ FQ FQ FQ FN FN
FQ FQ FQ FQ FQ FN FN GB GH GB GB HB HB HB HB JE JE JB
FE FE FE FE FE FN FN
FA FA FA FA FA FN FN GB GH GB GB HB HB HE HE JE JE JB
FZ FZ FZ FZ FN FN FN GB GG GB GB HB HB HE HE JE JE JB
FZ FZ FZ FZ FN FQ FQ GB GB GB GB HB HB
FN FN FN FN FN FQ FQ GB GB GB GB HB HE
FN FN FN FN FN FA FA GB GB GB GB HB HE
FN FN FN FN FN FZ FZ GB GB GB GB HB HG
FN FN FN FN FN FU FU GB GB GB GB
KE KE KE KE
KE KE KE KE
KE KE KE KE
KE KE KE KE
KE KE KE KE
KE KE KE KE
KE KE KE KE
KE KE KE KE
KE KE KE KE
KE KE KE KE
KE KE KE KE
KE KE
JE JE JB
JE JE JB
JE JB JB
JE JB JB
JB JB JB
JB JB JB
JB JB JB
JB JB JB
JB JB JB
JB JB JB
JB JB JD
JB JB JD
JB JB JG
JB JD JG
JB JD
KE KE
KE KE
KE
FN FN FN FN FE FU FU GB GB GB GB
FN FN FN FN FE FJ FJ GB GB GD GD
FN FN FN FN FA
FN FN FN FQ FZ
FQ FQ FQ FA FU
FE FE FE FZ FM
FZ FZ FZ FU
FU FU FU FM
FJ FJ FJ
GB GB GD GD
GB GB GK GK
GB GB GM GM
GB GD GM GM
GB GH
GD GN
GH
GK
0.12 µF
0.15 µF
0.18 µF
0.22 µF
0.27 µF
0.33 µF
0.39 µF
0.47 µF
FK FK FK
JB JF
JD JG
JG
JG
Rated Voltage (VDC)
Voltage Code
Cap
Code
8
4
3
5
1
2
A
5
1
2
A
5
1
2
A
5
1
2
5
1
2
A
Capacitance
Case Size/Series
C1210X
C1812X
C1825X
C2220X
C2225X
*Capacitance range Includes E24 decade values only. (i.e., 10, 11, 12, 13, 15, 16, 18, 20, 22, 24, 27, 30, 33, 36, 39, 43, 47, 51, 56, 62, 68, 75, 82 and 91)
These products are protected under US Patents 7,172,985 and 7,670,981, other patents pending, and any foreign counterparts.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016
7
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric, 10 – 250 VDC (Commercial & Automotive Grade)
Table 2A – Chip Thickness/Tape & Reel Packaging Quantities
Paper Quantity1
7" Reel 13" Reel
Plastic Quantity
Thickness Case Thickness ±
Code
Size1
Range (mm)
7" Reel
13" Reel
CJ
CH
DR
DD
DS
DF
DG
EQ
ER
ES
ET
EF
EH
FN
FQ
FE
FA
0603
0603
0805
0805
0805
0805
0805
1206
1206
1206
1206
1206
1206
1210
1210
1210
1210
1210
1210
1210
1210
1210
1812
1812
1812
1812
1812
1812
1812
1812
1825
1825
1825
2220
2220
2220
2220
2220
2225
0.80 ± 0.15
0.85 ± 0.07
0.78 ± 0.20
0.90 ± 0.10
1.00 ± 0.20
1.10 ± 0.10
1.25 ± 0.15
0.78 ± 0.20
0.90 ± 0.20
1.00 ± 0.20
1.10 ± 0.20
1.20 ± 0.15
1.60 ± 0.20
0.78 ± 0.20
0.90 ± 0.20
1.00 ± 0.10
1.10 ± 0.15
1.25 ± 0.20
1.55 ± 0.20
1.70 ± 0.20
1.85 ± 0.20
2.10 ± 0.20
1.00 ± 0.10
1.25 ± 0.15
1.40 ± 0.15
1.55 ± 0.10
1.60 ± 0.20
1.70 ± 0.15
1.70 ± 0.20
2.00 ± 0.20
1.10 ± 0.15
1.40 ± 0.15
1.60 ± 0.20
1.00 ± 0.15
1.30 ± 0.15
1.40 ± 0.15
1.50 ± 0.15
1.70 ± 0.15
1.40 ± 0.15
4,000
4,000
15,000
10,000
0
0
0
0
0
0
0
0
0
0
4,000
4,000
2,500
2,500
2,500
4,000
4,000
2,500
2,500
2,500
2,000
4,000
4,000
2,500
2,500
2,500
2,000
2,000
2,000
2,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
500
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
8,000
10,000
10,000
10,000
10,000
10,000
8,000
8,000
8,000
8,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
2,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
0
0
0
0
4,000
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
10,000
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
FZ
FU
FM
FJ
FK
GB
GD
GH
GG
GK
GJ
GN
GM
HB
HE
HG
JB
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
JD
JE
JF
JG
KE
7" Reel
13" Reel
7" Reel
13" Reel
Thickness
Code
Case
Size1
Thickness ±
Range (mm)
Paper Quantity1
Plastic Quantity
Package quantity based on finished chip thickness specifications.
1 If ordering using the 2 mm Tape and Reel pitch option, the packaging quantity outlined in the table above will be doubled. This option is limited to EIA 0603 (1608 metric)
case size devices. For more information regarding 2 mm pitch option see “Tape & Reel Packaging Information”.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016
8
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric, 10 – 250 VDC (Commercial & Automotive Grade)
Table 2B – Bulk Packaging Quantities
Loose Packaging
Packaging Type
Bulk Bag (default)
Packaging C-Spec1
N/A2
Case Size
Packaging Quantities (pieces/unit packaging)
EIA (in)
Metric (mm)
Minimum
Maximum
0402
0603
0805
1206
1210
1808
1812
1825
2220
2225
1005
1608
2012
3216
3225
4520
4532
4564
5650
5664
50,000
1
20,000
1 The "Packaging C-Spec" is a 4 to 8 digit code which identifies the packaging type and/or product grade. When ordering, the proper code must be included in the
15th through 22nd character positions of the ordering code. See "Ordering Information" section of this document for further details. Commercial Grade product
ordered without a packaging C-Spec will default to our standard "Bulk Bag" packaging. Contact KEMET if you require a bulk bag packaging option for Automotive
Grade products.
2 A packaging C-Spec (see note 1 above) is not required for "Bulk Bag" packaging (excluding Anti-Static Bulk Bag and Automotive Grade products). The 15th
through 22nd character positions of the ordering code should be left blank. All product ordered without a packaging C-Spec will default to out standard "Bulk Bag"
packaging.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016
9
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric, 10 – 250 VDC (Commercial & Automotive Grade)
Table 3 – Chip Capacitor Land Pattern Design Recommendations per IPC–7351 (mm)
Density Level A:
Maximum (Most)
Land Protrusion (mm)
Density Level B:
Median (Nominal)
Land Protrusion (mm)
Density Level C:
Minimum (Least)
Land Protrusion (mm)
EIA
Size
Code
Metric
Size
Code
C
Y
X
V1
V2
C
Y
X
V1
V2
C
Y
X
V1
V2
0603
0805
1206
1210
1812
1825
2220
2225
1608
2012
3216
3225
4532
4564
5650
5664
0.85
1.25
1.10
4.00
2.10
0.75
1.05
1.00
3.10
1.50
0.65
0.85
0.90
2.40
1.20
0.99
1.59
1.59
2.30
2.15
2.85
2.85
1.44
1.62
1.62
1.75
1.80
2.10
2.10
1.66
2.06
3.01
2.30
6.90
5.50
6.90
4.47
5.85
5.90
7.40
7.10
2.71
3.06
4.01
3.30
7.90
6.50
7.90
0.89
1.49
1.49
2.20
2.05
2.75
2.75
1.24
1.42
1.42
1.55
1.60
1.90
1.90
1.56
1.96
2.91
2.20
6.80
5.40
6.80
3.57
4.95
4.95
6.50
6.20
7.90
7.90
2.11
2.46
3.41
2.70
7.30
5.90
7.30
0.79
1.39
1.39
2.10
1.95
2.65
2.65
1.04
1.22
1.22
1.35
1.40
1.70
1.70
1.46
1.86
2.81
2.10
6.70
5.30
6.70
2.42
4.25
4.25
5.80
5.50
7.20
7.20
1.81
2.16
3.11
2.40
7.00
5.60
7.00
8.80
8.80
Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder
processes. KEMET only recommends wave soldering of EIA 0603, 0805, and 1206 case sizes.
Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes.
Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform qualification
testing based on the conditions outlined in IPC Standard 7351 (IPC–7351).
Image below based on Density Level B for an EIA 1210 case size.
V1
Y
Y
V2
X
X
C
C
Grid Placement Courtyard
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016 10
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric, 10 – 250 VDC (Commercial & Automotive Grade)
Soldering Process
Recommended Soldering Technique:
• Solder wave or solder reflow for EIA case sizes 0603, 0805 and 1206
• All other EIA case sizes are limited to solder reflow only
Recommended Reflow Soldering Profile:
KEMET’s families of surface mount multilayer ceramic capacitors (SMD MLCCs) are compatible with wave (single or dual), convection,
IR or vapor phase reflow techniques. Preheating of these components is recommended to avoid extreme thermal stress. KEMET’s
recommended profile conditions for convection and IR reflow reflect the profile conditions of the IPC/J-STD-020 standard for moisture
sensitivity testing. These devices can safely withstand a maximum of three reflow passes at these conditions.
TP
TL
Termination Finish
tP
Maximum Ramp Up Rate = 3°C/sec
Maximum Ramp Down Rate = 6°C/sec
Profile Feature
SnPb
100% Matte Sn
tL
Preheat/Soak
Tsmax
Tsmin
Temperature Minimum (TSmin
Temperature Maximum (TSmax
Time (tS) from TSmin to TSmax
)
100°C
150°C
150°C
200°C
)
tS
60 – 120 seconds
60 – 120 seconds
Ramp-Up Rate (TL to TP)
Liquidous Temperature (TL)
Time Above Liquidous (tL)
Peak Temperature (TP)
3°C/second maximum 3°C/second maximum
25
183°C
60 – 150 seconds
235°C
217°C
60 – 150 seconds
260°C
25° C to Peak
Time
Time Within 5°C of Maximum
20 seconds maximum 30 seconds maximum
Peak Temperature (tP)
Ramp-Down Rate (TP to TL) 6°C/second maximum 6°C/second maximum
Time 25°C to Peak
6 minutes maximum
8 minutes maximum
Temperature
Note 1: All temperatures refer to the center of the package, measured on the
capacitor body surface that is facing up during assembly reflow.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016 11
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric, 10 – 250 VDC (Commercial & Automotive Grade)
Table 4 – Performance & Reliability: Test Methods and Conditions
Stress
Reference
Test or Inspection Method
Terminal Strength
JIS–C–6429
Appendix 1, Note: Force of 1.8 kg for 60 seconds.
Appendix 2, Note: Standard termination system – 2.0 mm (minimum) for all except 3 mm for C0G.
Flexible termination system – 3.0 mm (minimum).
Board Flex
JIS–C–6429
Magnification 50 X. Conditions:
a) Method B, 4 hours @ 155°C, dry heat @ 235°C
b) Method B @ 215°C category 3
Solderability
J–STD–002
c) Method D, category 3 @ 260°C
Temperature Cycling
Biased Humidity
JESD22 Method JA–104
MIL–STD–202 Method 103
1,000 Cycles (−55°C to +125°C). Measurement at 24 hours +/- 4 hours after test conclusion.
Load Humidity: 1,000 hours 85°C/85% RH and rated voltage. Add 100 K ohm resistor. Measurement
at 24 hours +/- 4 hours after test conclusion.
Low Volt Humidity: 1,000 hours 85°C/85% RH and 1.5 V. Add 100 K ohm resistor.
Measurement at 24 hours +/- 4 hours after test conclusion.
t = 24 hours/cycle. Steps 7a and 7b not required.
Moisture Resistance
Thermal Shock
MIL–STD–202 Method 106
MIL–STD–202 Method 107
Measurement at 24 hours +/- 4 hours after test conclusion.
−55°C/+125°C. Note: Number of cycles required – 300, maximum transfer time – 20 seconds, dwell
time – 15 minutes. Air – Air.
MIL–STD–202 Method 108
/EIA–198
High Temperature Life
Storage Life
1,000 hours at 125°C (85°C for X5R, Z5U and Y5V) with 2 X rated voltage applied.
MIL–STD–202 Method 108 150°C, 0 VDC for 1,000 hours.
5 g's for 20 min., 12 cycles each of 3 orientations. Note: Use 8" X 5" PCB 0.031" thick 7 secure
MIL–STD–202 Method 204 points on one long side and 2 secure points at corners of opposite sides. Parts mounted within 2"
from any secure point. Test from 10 – 2,000 Hz
Vibration
Mechanical Shock
MIL–STD–202 Method 213 Figure 1 of Method 213, Condition F.
Resistance to Solvents MIL–STD–202 Method 215 Add aqueous wash chemical, OKEM Clean or equivalent.
Storage and Handling
Ceramic chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other
environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term
storage. In addition, packaging materials will be degraded by high temperature– reels may soften or warp and tape peel force may
increase. KEMET recommends that maximum storage temperature not exceed 40ºC and maximum storage humidity not exceed 70%
relative humidity. Temperature fluctuations should be minimized to avoid condensation on the parts and atmospheres should be free of
chlorine and sulfur bearing compounds. For optimized solderability chip stock should be used promptly, preferably within 1.5 years of
receipt.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016 12
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric, 10 – 250 VDC (Commercial & Automotive Grade)
Construction
Detailed Cross Section
Dielectric Material
(CaZrO3)
End Termination/
External Electrode
(Cu)
Barrier Layer
(Ni)
Termination Finish
(100% Matte Sn /
SnPb - 5% Pb min)
Epoxy Layer
(Ag)
Dielectric Material
(CaZrO3)
Inner Electrodes
(Ni)
End Termination/
External Electrode
(Cu)
Epoxy Layer
(Ag)
Barrier Layer
(Ni)
Termination Finish
(100% Matte Sn /
SnPb - 5% Pb min)
Inner Electrodes
(Ni)
Capacitor Marking (Optional):
Laser marking option is not available on:
• C0G, Ultra Stable X8R and Y5V dielectric devices
• EIA 0402 case size devices
• EIA 0603 case size devices with Flexible Termination option.
• KPS Commercial and Automotive grade stacked devices.
These capacitors are supplied unmarked only.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016 13
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric, 10 – 250 VDC (Commercial & Automotive Grade)
Tape & Reel Packaging Information
KEMET offers multilayer ceramic chip capacitors packaged in 8, 12 and 16 mm tape on 7" and 13" reels in accordance with EIA
Standard 481. This packaging system is compatible with all tape-fed automatic pick and place systems. See Table 2 for details on
reeling quantities for commercial chips.
Bar Code Label
Anti-Static Reel
®
Embossed Plastic* or
Punched Paper Carrier.
Chip and KPS Orientation in Pocket
(except 1825 Commercial, and 1825 and 2225 Military)
KEMET
Sprocket Holes
Embossment or Punched Cavity
8 mm, 12 mm
or 16 mm Carrier Tape
Anti-Static Cover Tape
(.10 mm (.004") Maximum Thickness)
178 mm (7.00")
or
330 mm (13.00")
*EIA 01005, 0201, 0402 and 0603 case sizes available on punched paper carrier only.
Table 5 – Carrier Tape Configuration, Embossed Plastic & Punched Paper (mm)
New 2 mm Pitch Reel Options*
Embossed Plastic Punched Paper
Tape
Packaging
Ordering Code
(C-Spec)
C-3190
7" Reel
13" Reel
7" Reel
13" Reel
EIA Case Size Size
(W)*
Packaging Type/Options
Pitch (P1)*
Pitch (P1)*
01005 – 0402
0603
8
8
2
2/4
4
2
2/4
4
Automotive grade 7" reel unmarked
Automotive grade 13" reel unmarked
Commercial grade 7" reel unmarked
Commercial grade 13" reel unmarked
C-3191
C-7081
0805
8
4
4
4
4
C-7082
1206 – 1210
1805 – 1808
≥ 1812
8
4
4
* 2 mm pitch reel only available for 0603 EIA case size.
2 mm pitch reel for 0805 EIA case size under development.
12
12
12
16
8
4
4
8
8
Benefits of Changing from 4 mm to 2 mm Pitching Spacing
• Lower placement costs
• Double the parts on each reel results in fewer reel
changes and increased efficiency
• Fewer reels result in lower packaging, shipping and
storage costs, reducing waste
KPS 1210
8
8
KPS 1812 & 2220
Array 0508 & 0612
12
4
12
4
*Refer to Figures 1 & 2 for W and P1 carrier tape reference locations.
*Refer to Tables 6 & 7 for tolerance specifications.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016 14
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric, 10 – 250 VDC (Commercial & Automotive Grade)
Figure 1 – Embossed (Plastic) Carrier Tape Dimensions
T
T
P2
[10 pitches cumulative
tolerance on tape ± 0.2 mm]
2
E
1
Po
ØDo
Ao
F
Ko
W
E
2
B
1
Bo
S
1
P
1
T
1
Embossment
For cavity size,
see Note 1 Table 4
Center Lines of Cavity
ØD
1
Cover Tape
is for tape feeder reference only,
including draft concentric about B
B
1
o
.
User Direction of Unreeling
Table 6 – Embossed (Plastic) Carrier Tape Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
D1 Minimum
Note 1
1.0
(0.039)
R Reference S1 Minimum
T
T1
Tape Size
8 mm
D0
E1
P0
P2
Note 2
Note 3
Maximum
Maximum
25.0
(0.984)
1.5 +0.10/-0.0
(0.059 +0.004/-0.0)
1.75 ±0.10
4.0 ±0.10
2.0 ±0.05
0.600
(0.024)
0.600
(0.024)
0.100
(0.004)
12 mm
16 mm
(0.069 ±0.004) (0.157 ±0.004) (0.079 ±0.002)
1.5
(0.059)
30
(1.181)
Variable Dimensions — Millimeters (Inches)
B1 Maximum
Note 4
4.35
(0.171)
E2
T2
W
Tape Size
8 mm
Pitch
F
P1
A0,B0 & K0
Minimum
6.25
(0.246)
Maximum
2.5
(0.098)
Maximum
8.3
(0.327)
3.5 ±0.05
(0.138 ±0.002) (0.157 ±0.004)
4.0 ±0.10
Single (4 mm)
Single (4 mm) &
Double (8 mm)
8.2
10.25
5.5 ±0.05
8.0 ±0.10
4.6
12.3
12 mm
16 mm
Note 5
(0.323)
(0.404)
(0.217 ±0.002) (0.315 ±0.004)
(0.181)
(0.484)
12.1
(0.476)
14.25
(0.561)
7.5 ±0.05 12.0 ±0.10
(0.138 ±0.002) (0.157 ±0.004)
4.6
(0.181)
16.3
(0.642)
Triple (12 mm)
1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and
hole location shall be applied independent of each other.
2. The tape with or without components shall pass around R without damage (see Figure 6).
3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481 paragraph 4.3 section b).
4. B1 dimension is a reference dimension for tape feeder clearance only.
5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that:
(a) the component does not protrude above the top surface of the carrier tape.
(b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
(c) rotation of the component is limited to 20° maximum for 8 and 12 mm tapes and 10° maximum for 16 mm tapes (see Figure 3).
(d) lateral movement of the component is restricted to 0.5 mm maximum for 8 and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 4).
(e) for KPS Series product, A0 and B0 are measured on a plane 0.3 mm above the bottom of the pocket.
(f) see Addendum in EIA Standard 481 for standards relating to more precise taping requirements.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016 15
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric, 10 – 250 VDC (Commercial & Automotive Grade)
Figure 2 – Punched (Paper) Carrier Tape Dimensions
T
P2
[10 pitches cumulative
tolerance on tape ± 0.2 mm]
E
1
Po
ØDo
0
A
F
W
2
E
0
B
Bottom Cover Tape
P
1
G
Cavity Size,
See
1
T
1
T
Top Cover Tape
Center Lines of Cavity
Note 1, Table 7
Bottom Cover Tape
User Direction of Unreeling
Table 7 – Punched (Paper) Carrier Tape Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
R Reference
Note 2
Tape Size
8 mm
D0
E1
P0
P2
T1 Maximum
G Minimum
0.10
1.5 +0.10 -0.0
(0.059 +0.004 -0.0)
1.75 ±0.10
(0.069 ±0.004)
4.0 ±0.10
(0.157 ±0.004)
2.0 ±0.05
(0.079 ±0.002)
0.75
(0.030)
25
(0.984)
(0.004)
Maximum
Variable Dimensions — Millimeters (Inches)
Tape Size
8 mm
Pitch
E2 Minimum
F
P1
T Maximum
W Maximum
A0 B0
2.0 ±0.05
(0.079 ±0.002)
4.0 ±0.10
8.3
(0.327)
8.3
Half (2 mm)
Single (4 mm)
6.25
(0.246)
3.5 ±0.05
(0.138 ±0.002)
1.1
(0.098)
Note 1
8 mm
(0.157 ±0.004)
(0.327)
1. The cavity defined by A0, B0 and T shall surround the component with sufficient clearance that:
a) the component does not protrude beyond either surface of the carrier tape.
b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
c) rotation of the component is limited to 20° maximum (see Figure 3).
d) lateral movement of the component is restricted to 0.5 mm maximum (see Figure 4).
e) see Addendum in EIA Standard 481 for standards relating to more precise taping requirements.
2. The tape with or without components shall pass around R without damage (see Figure 6).
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016 16
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric, 10 – 250 VDC (Commercial & Automotive Grade)
Packaging Information Performance Notes
1. Cover Tape Break Force: 1.0 Kg minimum.
2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be:
Tape Width
8 mm
Peel Strength
0.1 to 1.0 Newton (10 to 100 gf)
0.1 to 1.3 Newton (10 to 130 gf)
12 and 16 mm
The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165° to 180°
from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 ±10 mm/minute.
3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA
Standards 556 and 624.
Figure 3 – Maximum Component Rotation
°
T
Maximum Component Rotation
Top View
Maximum Component Rotation
Side View
Typical Pocket Centerline
Tape
Maximum
°
°
T
s
Width (mm) Rotation (
)
8,12
16 – 200
20
10
Bo
Tape
Maximum
°
S
Width (mm) Rotation (
)
8,12
16 – 56
72 – 200
20
10
5
Typical Component Centerline
Ao
Figure 5 – Bending Radius
Figure 4 – Maximum Lateral Movement
Embossed
Carrier
Punched
Carrier
8 mm & 12 mm Tape
16 mm Tape
0.5 mm maximum
0.5 mm maximum
1.0 mm maximum
1.0 mm maximum
R
Bending
Radius
R
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016 17
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric, 10 – 250 VDC (Commercial & Automotive Grade)
Figure 6 – Reel Dimensions
Full Radius,
W3 (Includes
flange distortion
at outer edge)
Access Hole at
Slot Location
(Ø 40 mm minimum)
See Note
W
2 (Measured at hub)
D
(See Note)
A
N
C
(Arbor hole
W
1 (Measured at hub)
diameter)
If present,
tape slot in core
for tape start:
2.5 mm minimum width x
10.0 mm minimum depth
B
(see Note)
Note: Drive spokes optional; if used, dimensions B and D shall apply.
Table 8 – Reel Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
Tape Size
8 mm
A
B Minimum
C
D Minimum
178 ±0.20
(7.008 ±0.008)
or
330 ±0.20
(13.000 ±0.008)
1.5
(0.059)
13.0 +0.5/-0.2
(0.521 +0.02/-0.008)
20.2
(0.795)
12 mm
16 mm
Variable Dimensions — Millimeters (Inches)
Tape Size
8 mm
N Minimum
W1
W2 Maximum
W3
8.4 +1.5/-0.0
(0.331 +0.059/-0.0)
14.4
(0.567)
50
(1.969)
12.4 +2.0/-0.0
18.4
Shall accommodate tape width
without interference
12 mm
16 mm
(0.488 +0.078/-0.0)
(0.724)
16.4 +2.0/-0.0
(0.646 +0.078/-0.0)
22.4
(0.882)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016 18
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric, 10 – 250 VDC (Commercial & Automotive Grade)
Figure 7 – Tape Leader & Trailer Dimensions
Embossed Carrier
Carrier Tape
Round Sprocket Holes
Punched Carrier
8 mm & 12 mm only
START
END
Top Cover Tape
Elongated Sprocket Holes
(32 mm tape and wider)
100 mm
Minimum Leader
400 mm Minimum
Trailer
160 mm Minimum
Components
Top Cover Tape
Figure 8 – Maximum Camber
Elongated sprocket holes
(32 mm & wider tapes)
Carrier Tape
Round Sprocket Holes
1 mm Maximum, either direction
Straight Edge
250 mm
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016 19
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric, 10 – 250 VDC (Commercial & Automotive Grade)
KEMET Corporation
World Headquarters
Europe
Asia
Southern Europe
Sasso Marconi, Italy
Tel: 39-051-939111
Northeast Asia
Hong Kong
Tel: 852-2305-1168
2835 KEMET Way
Simpsonville, SC 29681
Skopje, Macedonia
Tel: 389-2-55-14-623
Shenzhen, China
Tel: 86-755-2518-1306
Mailing Address:
P.O. Box 5928
Greenville, SC 29606
Beijing, China
Central Europe
Landsberg, Germany
Tel: 49-8191-3350800
Tel: 86-10-5877-1075
www.kemet.com
Tel: 864-963-6300
Fax: 864-963-6521
Shanghai, China
Tel: 86-21-6447-0707
Kamen, Germany
Tel: 49-2307-438110
Corporate Offices
Fort Lauderdale, FL
Tel: 954-766-2800
Seoul, South Korea
Tel: 82-2-6294-0550
Northern Europe
Wyboston, United Kingdom
Tel: 44-1480-273082
Taipei, Taiwan
Tel: 886-2-27528585
North America
Northeast
Wilmington, MA
Tel: 978-658-1663
Espoo, Finland
Tel: 358-9-5406-5000
Southeast Asia
Singapore
Tel: 65-6701-8033
Southeast
Lake Mary, FL
Tel: 407-855-8886
Penang, Malaysia
Tel: 60-4-6430200
Central
Novi, MI
Tel: 248-994-1030
Bangalore, India
Tel: 91-806-53-76817
Irving, TX
Tel: 972-915-6041
West
Milpitas, CA
Tel: 408-433-9950
Mexico
Guadalajara, Jalisco
Tel: 52-33-3123-2141
Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not
assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of
KEMET Electronics Corporation.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016 20
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), C0G Dielectric, 10 – 250 VDC (Commercial & Automotive Grade)
Disclaimer
All product specifications, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and
verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.
All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are
not intended to constitute – and KEMET specifically disclaims – any warranty concerning suitability for a specific customer application or use. The Information is intended for use only
by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise
provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained.
Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still
occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective
circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage.
Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not
be required.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1062_C0G_FT-CAP_SMD • 5/23/2016 21
相关型号:
C1210X563B3GALTU
Flexible Termination System (FT-CAP), C0G Dielectric, 10 - 250 VDC (Commercial & Automotive Grade)
KEMET
C1210X563B4GACTU
Flexible Termination System (FT-CAP), C0G Dielectric, 10 - 250 VDC (Commercial & Automotive Grade)
KEMET
C1210X563B4GALTU
Flexible Termination System (FT-CAP), C0G Dielectric, 10 - 250 VDC (Commercial & Automotive Grade)
KEMET
C1210X563B5GACTU
Flexible Termination System (FT-CAP), C0G Dielectric, 10 - 250 VDC (Commercial & Automotive Grade)
KEMET
C1210X563B5GALTU
Flexible Termination System (FT-CAP), C0G Dielectric, 10 - 250 VDC (Commercial & Automotive Grade)
KEMET
C1210X563B8GACTU
Flexible Termination System (FT-CAP), C0G Dielectric, 10 - 250 VDC (Commercial & Automotive Grade)
KEMET
C1210X563B8GALTU
Flexible Termination System (FT-CAP), C0G Dielectric, 10 - 250 VDC (Commercial & Automotive Grade)
KEMET
C1210X563BAGACTU
Flexible Termination System (FT-CAP), C0G Dielectric, 10 - 250 VDC (Commercial & Automotive Grade)
KEMET
C1210X563BAGALTU
Flexible Termination System (FT-CAP), C0G Dielectric, 10 - 250 VDC (Commercial & Automotive Grade)
KEMET
C1210X563C1GACTU
Flexible Termination System (FT-CAP), C0G Dielectric, 10 - 250 VDC (Commercial & Automotive Grade)
KEMET
C1210X563C1GALTU
Flexible Termination System (FT-CAP), C0G Dielectric, 10 - 250 VDC (Commercial & Automotive Grade)
KEMET
C1210X563C2GACTU
Flexible Termination System (FT-CAP), C0G Dielectric, 10 - 250 VDC (Commercial & Automotive Grade)
KEMET
©2020 ICPDF网 联系我们和版权申明