C1210C475K3NACTU_技术文档

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC

(Commercial & Automotive Grade)

Overview

KEMET’s X8L dielectric features a 150°C maximum

operating temperature and is considered “general

purpose high temperature.” These components are

ﬁxed, ceramic dielectric capacitors suited for high

temperature bypass and decoupling applications or

frequency discriminating circuits where Q and stability of

capacitance characteristics are not critical. X8L exhibits a

These devices are available with KEMET's Flexible

termination technology which inhibits the transfer of board

stress to the rigid ceramic body, therefore mitigating ﬂex

cracks which can result in low IR or short circuit failures.

Although ﬂexible termination technology does not eliminate

the potential for mechanical damage that may propagate

during extreme environmental and handling conditions,

predictable change in capacitance with respect to time and it does provide superior ﬂex performance over standard

voltage and boasts a minimal change in capacitance with

reference to ambient temperature up to 125°C. Beyond

125°C X8L displays a wider variation in capacitance.

Capacitance change is limited to ±15% from −55°C to

+125°C and +15, −40% from 125°C to 150°C.

termination systems.

In addition to commercial grade, automotive grade

devices are available and meet the demanding Automotive

Electronics Council's AEC–Q200 qualiﬁcation requirements.

Driven by the demand for a more robust and reliable

component, X8L dielectric capacitors were developed for

critical applications where reliability at higher operating

temperatures are a concern. These capacitors are widely

used in automotive circuits as well as general high

temperature applications. Concerned with ﬂex cracks

resulting from excessive tensile and shear stresses

produced during board ﬂexure and thermal cycling?

Click image above for interactive 3D content

Open PDF in Adobe Reader for full functionality

Ordering Information

C

1210

X

106

K

8

N

A

C

TU

Rated

Failure

Case Size Speciﬁcation/ Capacitance Capacitance

Packaging/Grade

(C-Spec)

Ceramic

Voltage Dielectric Rate/

(VDC)

Termination Finish²

(L" x W")

Series¹

Code (pF)

Tolerance

Design

0402

0603

0805

1206

1210

C = Standard

X = Flexible

Termination

Two

signiﬁcant

digits +

number of

zeros

J = ±5%

K = ±10%

M = ±20%

8 = 10

4 = 16

3 = 25

5 = 50

N = X8L A = N/A C = 100% Matte Sn

See "Packaging

L = SnPb (5% Pb minimum) C-Spec Ordering

Options Table"

below

¹The ﬂexible termination option is not available on EIA 0402 case size product. "C" must be used in the 6th character position when ordering this case

size.

²Additional termination ﬁnish options may be available. Contact KEMET for details.

²SnPb termination ﬁnish option is not available on Automotive Grade product.

One world. One KEMET

C1008_X8L_150C_SMD • 11/29/2017

1

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

Packaging C-Spec Ordering Options Table

Packaging/Grade

Packaging Type

Ordering Code (C-Spec)

Commercial Grade¹

Bulk Bag

Not Required (Blank)

TU

7" Reel/Unmarked

7411 (EIA 0603 and smaller case sizes)

7210 (EIA 0805 and larger case sizes)

13" Reel/Unmarked

7" Reel/Marked

TM

7040 (EIA 0603 and smaller case sizes)

7215 (EIA 0805 and larger case sizes)

13" Reel/Marked

7" Reel/Unmarked/2 mm pitch²

13" Reel/Unmarked/2 mm pitch²

7081

7082

Automotive Grade³

7" Reel

AUTO

AUTO7411 (EIA 0603 and smaller case sizes)

AUTO7210 (EIA 0805 and larger case sizes)

13" Reel/Unmarked

7" Reel/Unmarked/2 mm pitch²

13" Reel/Unmarked/2 mm pitch²

3190

3191

¹Default packaging is "Bulk Bag". An ordering code C-Spec is not required for "Bulk Bag" packaging.

¹The terms "Marked" and "Unmarked" pertain to laser marking option of capacitors. All packaging options labeled as "Unmarked" will contain capacitors

that have not been laser marked.

²The 2 mm pitch option allows for double the packaging quantity of capacitors on a given reel size. This option is limited to EIA 0603 (1608 metric) case

size devices. For more information regarding 2 mm pitch option see "Tape & Reel Packaging Information".

³Reeling tape options (Paper or Plastic) are dependent on capacitor case size (L" x W") and thickness dimension. See "Chip Thickness/Tape & Reel

Packaging Quantities" and "Tape & Reel Packaging Information".

³For additional Information regarding "AUTO" C-Spec options, see "Automotive C-Spec Information".

³All Automotive packaging C-Specs listed exclude the option to laser mark components. Please contact KEMET if you require a laser marked option. For

more information see "Capacitor Marking".

Beneﬁts

• −55°C to +150°C operating temperature range

• Lead (Pb)-free, RoHS and REACH compliant

• EIA 0402, 0603, 0805, 1206, and 1210 case sizes

• DC voltage ratings of 10 V, 16 V, 25 V, and 50 V

• Capacitance offerings ranging from 0.012 μF to 10 μF

• Non-polar device, minimizing installation concerns

• 100% pure matte tin-plated termination ﬁnish allowing for

excellent solderability

• SnPb termination ﬁnish option available upon request

(5% Pb minimum)

• Available capacitance tolerances of ±5%, ±10%, and ±20% • Flexible termination option available upon request

• Commercial & Automotive (AEC–Q200) grades available

Applications

Typical applications include use in extreme environments such as down-hole oil exploration, under-hood automotive, military

and aerospace.

C1008_X8L_150C_SMD • 11/29/2017

2

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

Automotive C-Spec Information

KEMET Automotive Grade products meet or exceed the requirements outlined by the Automotive Electronics Council.

Details regarding test methods and conditions are referenced in document AEC–Q200, Stress Test Qualiﬁcation for Passive

Components. These products are supported by a Product Change Notiﬁcation (PCN) and Production Part Approval Process

warrant (PPAP).

Automotive products offered through our distribution channel have been assigned an inclusive ordering code C-Spec, “AUTO.”

This C-Spec was developed in order to better serve small and medium-sized companies that prefer an automotive grade

component without the requirement to submit a customer Source Controlled Drawing (SCD) or speciﬁcation for review by a

KEMET engineering specialist. This C-Spec is therefore not intended for use by KEMET’s OEM Automotive customers and are

not granted the same “privileges” as other automotive C-Specs. Customer PCN approval and PPAP request levels are limited

(see details below).

Product Change Notiﬁcation (PCN)

The KEMET Product Change Notiﬁcation system is used to communicate primarily the following types of changes:

• Product/process changes that affect product form, ﬁt, function, and/or reliability

• Changes in manufacturing site

• Product obsolescence

Customer Notiﬁcation due to:

KEMET Automotive

C-Spec

Days prior to

implementation

Process/Product change

Obsolescence*

KEMET assigned¹

AUTO

Yes (with approval and sign off)

Yes (without approval)

Yes

180 days minimum

90 days minimum

¹KEMET assigned C-Specs require the submittal of a customer SCD or customer speciﬁcation for review. For additional information contact KEMET.

Production Part Approval Process (PPAP)

The purpose of the Production Part Approval Process is:

• To ensure that supplier can meet the manufacturability and quality requirements for the purchased parts.

• To provide the evidence that all customer engineering design record and speciﬁcation requirements are properly

understood and fulﬁlled by the manufacturing organization.

• To demonstrate that the established manufacturing process has the potential to produce the part.

PPAP (Product Part Approval Process) Level

KEMET Automotive

C-Spec

1

●

○

2

3

●

○

4

5

KEMET assigned¹

AUTO

●

¹KEMET assigned C-Specs require the submittal of a customer SCD or customer speciﬁcation for review. For additional information contact KEMET.

● Part number speciﬁc PPAP available

○ Product family PPAP only

C1008_X8L_150C_SMD • 11/29/2017

3

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

Dimensions – Standard Termination – Millimeters (Inches)

L

W

T

B

S

Metric Size

Code

L

W

Width

T

B

Mounting

Technique

EIA Size Code

Separation

Minimum

Length

Thickness

Bandwidth

1.00 (0.040)

±0.05 (0.002)

1.60 (0.063)

±0.15 (0.006)

2.00 (0.079)

±0.20 (0.008)

3.20 (0.126)

±0.20 (0.008)

3.20 (0.126)

±0.20 (0.008)

0.50 (0.020)

±0.05 (0.002)

0.80 (0.032)

±0.15 (0.006)

1.25 (0.049)

±0.20 (0.008)

1.60 (0.063)

±0.20 (0.008)

2.50 (0.098)

±0.20 (0.008)

0.30 (0.012)

±0.10 (0.004)

0.35 (0.014)

±0.15 (0.006)

0.50 (0.02)

±0.25 (0.010)

0.50 (0.02)

±0.25 (0.010)

0.50 (0.02)

±0.25 (0.010)

Solder Reﬂow

0402

0603

0805

1206

1210

1005

1608

2012

3216

3225

0.30 (0.012)

0.70 (0.028)

0.75 (0.030)

Only

See Table 2 for

Thickness

Solder Wave or

Solder Reﬂow

N/A

Solder Reﬂow

Only

Dimensions – Flexible Termination – Millimeters (Inches)

S

Metric Size

Code

L

W

Width

T

B

Mounting

Technique

EIA Size Code

Separation

Minimum

Length

Thickness

Bandwidth

1.60 (0.063)

±0.17 (0.007)

2.00 (0.079)

±0.30 (0.012)

3.30 (0.130)

±0.40 (0.016)

3.30 (0.130)

±0.40 (0.016)

0.80 (0.032)

±0.15 (0.006)

1.25 (0.049)

±0.30 (0.012)

1.60 (0.063)

±0.35 (0.013)

2.60 (0.102)

±0.30(0.012)

0.45 (0.018)

±0.15 (0.006)

0.50 (0.020)

±0.25 (0.010)

0.60 (0.024)

±0.25 (0.010)

0.60 (0.024)

±0.25 (0.010)

0603

0805

1206

1210

1608

2012

3216

3225

0.58 (0.023)

Solder Wave

or

Solder Reﬂow

0.75 (0.030)

See Table 2 for

Thickness

N/A

Solder Reﬂow

Only

C1008_X8L_150C_SMD • 11/29/2017

4

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

Qualiﬁcation/Certiﬁcation

Commercial Grade products are subject to internal qualiﬁcation. Details regarding test methods and conditions are

referenced in Table 4, Performance & Reliability.

Automotive Grade products meet or exceed the requirements outlined by the Automotive Electronics Council. Details

regarding test methods and conditions are referenced in document AEC–Q200, Stress Test Qualiﬁcation for Passive

Components. For additional information regarding the Automotive Electronics Council and AEC–Q200, please visit their

website at www.aecouncil.com.

Environmental Compliance

Lead (Pb)-free, RoHS, and REACH compliant without exemptions (excluding SnPb termination ﬁnish option).

Electrical Parameters/Characteristics

Item

Parameters/Characteristics

Operating Temperature Range

−55°C to +150°C

Capacitance Change with Reference to

+25°C and 0 VDC Applied (TCC)

±15% (−55ºC to 125ºC), +15, −40% (125ºC to 150ºC)

¹Aging Rate (Maximum % Capacitance Loss/Decade Hour)

3.0%

250% of rated voltage

(5±1 seconds and charge/discharge not exceeding 50 mA)

²Dielectric Withstanding Voltage (DWV)

³Dissipation Factor (DF) Maximum Limit at 25°C

⁴Insulation Resistance (IR) Minimum Limit at 25°C

3.5% ( ≤ 16V) and 2.5% ( ≥ 25V)

500 megohm microfarads or 10 GΩ

(Rated voltage applied for 120±5 seconds at 25°C)

¹Regarding Aging Rate: Capacitance measurements (including tolerance) are indexed to a referee time of 1,000 hours.

²DWV is the voltage a capacitor can withstand (survive) for a short period of time. It exceeds the nominal and continuous working voltage of the

capacitor.

³Capacitance and dissipation factor (DF) measured under the following conditions:

1kHz ± 50Hz and 1.0 ± 0.2 Vrms if capacitance ≤10µF

120Hz ± 10Hz and 0.5 ± 0.1 Vrms if capacitance >10µF

⁴To obtain IR limit, divide MΩ-µF value by the capacitance and compare to GΩ limit. Select the lower of the two limits.

Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 & Agilent E4980 have a feature known as

Automatic Level Control (ALC). The ALC feature should be switched to "ON".

Post Environmental Limits

High Temperature Life, Biased Humidity, Moisture Resistance

Rated DC

Voltage

Capacitance Dissipation Factor Capacitance

Insulation

Dielectric

X8L

Value

(Maximum %)

Shift

Resistance

≥ 25

≤ 16

3.0

5.0

10% of Initial

Limit

All

±20%

C1008_X8L_150C_SMD • 11/29/2017

5

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

Table 1 – Capacitance Range/Selection Waterfall (0402 – 1210 Case Sizes)

Case Size/

Series

C0402C

C0603C

C0805C

C1206C

C1210C

Cap

Code

Cap

Voltage Code

9

8

4

3

9

8

4

3

5

9

8

4

3

5

9

8

4

3

5

9

8

4

3

5

Rated Voltage (VDC) 6.3 10 16 25 6.3 10 16 25 50 6.3 10 16 25 50 6.3 10 16 25 50 6.3 10 16 25 50

Capacitance Tolerance

Product Availability and Chip Thickness Codes See Table 2 for Chip Thickness Dimensions

12,000 pF

15,000 pF

18,000 pF

22,000 pF

27,000 pF

33,000 pF

39,000 pF

47,000 pF

56,000 pF

68,000 pF

82,000 pF

0.10 µF

0.12 µF

0.15 µF

0.18 µF

0.22 µF

0.27 µF

0.33 µF

0.39 µF

0.47 µF

0.56 µF

0.68 µF

0.82 µF

1.0 µF

1.2 µF

1.5 µF

1.8 µF

2.2 µF

2.7 µF

3.3 µF

3.9 µF

4.7 µF

5.6 µF

6.8 µF

8.2 µF

10 µF

123

153

183

223

273

333

393

473

563

683

823

104

124

154

184

224

274

334

394

474

564

684

824

105

125

155

185

225

275

335

395

475

565

685

825

106

J

K

M

BB BB BB BB

BB BB BB

BB BB

CF CF CF CF CF

BB BB

CF CF CF CF

CF CF CF

DG DG DG DG DG

DP DP DP DP DG

DP DP DP DP

DE DE DE DE

DG DG DH DH

DG DG DG

CF CF CF

FD FD FD FD FD

EG EG EG EG EG FD FD FD FD FD

FF FF FF FF FF

FG FG FG FG FG

FL FL FL FL FL

DG DG DG

ED ED ED ED

EH EH EH EH

EF EF EH EH

EH EH EH

FM FM FM FM FM

FG FG FG FG

FG FG FH FH

FM FM FM FM

FG FG FK FK

FG FG FS FS

FH FH FH

FM FM FM

FK FK FK

FS FS FS

Rated Voltage (VDC) 6.3 10 16 25 6.3 10 16 25 50 6.3 10 16 25 50 6.3 10 16 25 50 6.3 10 16 25 50

Voltage Code

9

8

4

3

9

8

4

3

5

9

8

4

3

5

9

8

4

3

5

9

8

4

3

5

Cap

Cap Code

Case Size/Series

C0402C

C0603C

C0805C

C1206C

C1210C

C1008_X8L_150C_SMD • 11/29/2017

6

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

Table 2A – Chip Thickness/Tape & Reel Packaging Quantities

Paper Quantity¹

Plastic Quantity

Thickness Case Thickness ±

Code

Size¹Range (mm)

7" Reel

13" Reel

7" Reel

13" Reel

BB

CF

DP

DE

DG

DH

ED

EF

EG

EH

FD

FF

FG

FL

FH

FM

FK

FS

0402

0603

0805

1206

1210

0.50 ± 0.05

0.80 ± 0.07

0.90 ± 0.10

1.00 ± 0.10

1.25 ± 0.15

1.25 ± 0.20

1.00 ± 0.10

1.20 ± 0.15

1.60 ± 0.15

1.60 ± 0.20

0.95 ± 0.10

1.10 ± 0.10

1.25 ± 0.15

1.40 ± 0.15

1.55 ± 0.15

1.70 ± 0.20

2.10 ± 0.20

2.50 ± 0.30

10,000

4,000

50,000

15,000

0

2,500

2,000

4,000

2,500

2,000

1,000

10,000

8,000

10,000

8,000

4,000

7" Reel

13" Reel

7" Reel

13" Reel

Thickness

Code

Case

Size¹

Thickness ±

Range (mm)

Paper Quantity¹

Plastic Quantity

Package quantity based on ﬁnished chip thickness speciﬁcations.

¹If ordering using the 2 mm Tape and Reel pitch option, the packaging quantity outlined in the table above will be doubled. This option is limited to EIA

0603 (1608 metric) case size devices. For more information regarding 2 mm pitch option see "Tape & Reel Packaging Information".

C1008_X8L_150C_SMD • 11/29/2017

7

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

Table 2B – Bulk Packaging Quantities

Loose Packaging

Packaging Type

Bulk Bag (default)

Packaging C-Spec¹

N/A²

Case Size

Packaging Quantities (pieces/unit packaging)

EIA (in)

Metric (mm)

Minimum

Maximum

0402

0603

0805

1206

1210

1808

1812

1825

2220

2225

1005

1608

2012

3216

3225

4520

4532

4564

5650

5664

50,000

1

20,000

¹The "Packaging C-Spec" is a 4 to 8 digit code which identiﬁes the packaging type and/or product grade. When ordering, the proper code must be

included in the 15th through 22nd character positions of the ordering code. See "Ordering Information" section of this document for further details.

Commercial Grade product ordered without a packaging C-Spec will default to our standard "Bulk Bag" packaging. Contact KEMET if you require a bulk

bag packaging option for Automotive Grade products.

²A packaging C-Spec (see note 1 above) is not required for "Bulk Bag" packaging (excluding Anti-Static Bulk Bag and Automotive Grade products). The

15th through 22nd character positions of the ordering code should be left blank. All product ordered without a packaging C-Spec will default to our

standard "Bulk Bag" packaging.

C1008_X8L_150C_SMD • 11/29/2017

8

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

Table 3A – Land Pattern Design Recommendations per IPC–7351 – Standard Termination

Density Level A:

Maximum (Most)

Density Level B:

Median (Nominal)

Land Protrusion (mm)

Density Level C:

Minimum (Least)

EIA

Size

Code

Metric

Size

Code

Land Protrusion (mm)

C

Y

X

V1

V2

C

Y

X

V1

V2

C

Y

X

V1

V2

0402

0603

0805

1206

1210

1005

1608

2012

3216

3225

0.50

0.72

2.20

1.20

0.45

0.62

1.90

1.00

0.40

0.52

1.60

0.80

0.90

0.99

1.59

1.15

1.44

1.62

1.10

1.66

2.06

3.01

4.00

4.47

5.85

5.90

2.10

2.71

3.06

4.01

0.80

0.89

1.49

0.95

1.24

1.42

1.00

1.56

1.96

2.91

3.10

3.57

4.95

1.50

2.11

2.46

3.41

0.60

0.79

1.39

0.75

1.04

1.22

0.90

1.46

1.86

2.81

2.40

2.42

4.25

1.20

1.81

2.16

3.11

Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reﬂow

solder processes. KEMET only recommends wave soldering of EIA 0603, 0805 and 1206 case sizes.

Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reﬂow solder processes.

Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform

qualiﬁcation testing based on the conditions outlined in IPC Standard 7351 (IPC–7351).

Image below based on Density Level B for an EIA 1210 case size.

V1

Y

V2

X

C

Grid Placement Courtyard

C1008_X8L_150C_SMD • 11/29/2017

9

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

Table 3B – Land Pattern Design Recommendations per IPC–7351 – Flexible Termination

Density Level A:

Maximum (Most)

Density Level B:

Median (Nominal)

Land Protrusion (mm)

Density Level C:

Minimum (Least)

EIA

Size

Code

Metric

Size

Code

Land Protrusion (mm)

C

Y

X

V1

V2

C

Y

X

V1

V2

C

Y

X

V1

V2

0603

0805

1206

1210

1608

2012

3216

3225

0.85

1.25

1.10

4.00

2.10

0.75

1.05

1.00

3.10

1.50

0.65

0.85

0.90

2.40

1.20

1.00

1.60

1.35

1.65

1.55

1.90

2.80

4.40

5.90

2.60

2.90

3.80

0.90

1.50

1.15

1.45

1.80

2.70

3.50

5.00

2.00

2.30

3.20

0.75

1.40

0.95

1.25

1.35

1.70

2.60

2.80

4.30

1.70

2.00

2.90

Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reﬂow

solder processes. KEMET only recommends wave soldering of EIA 0603, 0805 and 1206 case sizes.

Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reﬂow solder processes.

Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform

qualiﬁcation testing based on the conditions outlined in IPC Standard 7351 (IPC–7351).

Image below based on Density Level B for an EIA 1210 case size.

V1

Y

V2

X

C

Grid Placement Courtyard

C1008_X8L_150C_SMD • 11/29/2017 10

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

Soldering Process

Recommended Soldering Technique:

• Solder wave or solder reﬂow for EIA case sizes 0603, 0805 and 1206

• All other EIA case sizes are limited to solder reﬂow only

Recommended Reﬂow Soldering Proﬁle:

KEMET’s families of surface mount multilayer ceramic capacitors (SMD MLCCs) are compatible with wave (single or dual),

convection, IR or vapor phase reﬂow techniques. Preheating of these components is recommended to avoid extreme thermal

stress. KEMET’s recommended proﬁle conditions for convection and IR reﬂow reﬂect the proﬁle conditions of the IPC/

J-STD-020 standard for moisture sensitivity testing. These devices can safely withstand a maximum of three reﬂow passes

at these conditions.

Termination Finish

T_ꢂ

T_L

t_ꢂ

Proﬁle Feature

Maꢁimum ꢃamp ꢄp ꢃate ꢅ ꢆ°Cꢇsecond

Maꢁimum ꢃamp Doꢈn ꢃate ꢅ ꢉ°Cꢇsecond

SnPb

100% Matte Sn

t_L

Preheat/Soak

Temperature Minimum (T_Smin

)

100°C

150°C

200°C

T_smaꢁ

T_smin

Temperature Maximum (T_Smax

Time (t_S) from T_Sminto T_Smax

)

60 – 120 seconds

t_s

3°C/second

maximum

3°C/second

maximum

Ramp-Up Rate (T_Lto T_P)

ꢀ5

ꢀ5°C to ꢂeaꢊ

Liquidous Temperature (T_L)

Time Above Liquidous (t_L)

Peak Temperature (T_P)

183°C

60 – 150 seconds

235°C

217°C

60 – 150 seconds

260°C

Time

Time Within 5°C of Maximum

Peak Temperature (t_P)

20 seconds

maximum

30 seconds

maximum

6°C/second

maximum

6°C/second

maximum

Ramp-Down Rate (T_Pto T_L)

Time 25°C to Peak

Temperature

6 minutes

maximum

8 minutes

maximum

Note 1: All temperatures refer to the center of the package, measured on the

capacitor body surface that is facing up during assembly reﬂow.

C1008_X8L_150C_SMD • 11/29/2017 11

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

Table 4 – Performance & Reliability: Test Methods and Conditions

Stress

Terminal Strength

Board Flex

Reference

JIS–C–6429

Test or Inspection Method

Appendix 1, Note: Force of 1.8 kg for 60 seconds.

Appendix 2, Note: Standard termination system – 2.0 mm (minimum) for all except 3 mm

for C0G. Flexible termination system – 3.0 mm (minimum).

Magniﬁcation 50 X. Conditions:

a) Method B, 4 hours at 155°C, dry heat at 235°C

b) Method B at 215°C category 3

Solderability

J–STD–002

c) Method D, category 3 at 260°C

Temperature Cycling

Biased Humidity

JESD22 Method JA–104 1,000 cycles (−55°C to +150°C). Measurement at 24 hours +/− 4 hours after test conclusion.

Load Humidity: 1,000 hours 85°C/85%RH and rated voltage. Add 100K ohm resistor.

MIL–STD–202 Method

103

Measurement at 24 hours +/− 4 hours after test conclusion.

Low Volt Humidity: 1,000 hours 85°C/85% RH and 1.5 V. Add 100 K ohm resistor.

Measurement at 24 hours +/− 4 hours after test conclusion.

MIL–STD–202 Method

t = 24 hours/cycle. Steps 7a and 7b not required. Measurement at 24 hours. +/− 4 hours

Moisture Resistance

Thermal Shock

after test conclusion.

106

MIL–STD–202 Method

−55°C/+150. Note: Number of cycles required – 300. Maximum transfer time – 20 seconds.

Dwell time – 15 minutes. Air – Air.

107

MIL–STD–202 Method

108

High Temperature Life

1,000 hours at 150°C with 2 X rated voltage applied.

/EIA–198

MIL–STD–202 Method

108

Storage Life

Vibration

150°C, 0 VDC for 1,000 hours.

5 g's for 20 min., 12 cycles each of 3 orientations. Note: Use 8" X 5" PCB 0.031" thick 7

secure points on one long side and 2 secure points at corners of opposite sides. Parts

mounted within 2" from any secure point. Test from 10 – 2,000 Hz

MIL–STD–202 Method

204

MIL–STD–202 Method

Mechanical Shock

Figure 1 of Method 213, Condition F.

213

MIL–STD–202 Method

215

Resistance to Solvents

Add aqueous wash chemical, OKEM Clean or equivalent.

Storage and Handling

Ceramic chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in

other environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres,

and long term storage. In addition, packaging materials will be degraded by high temperature–reels may soften or warp

and tape peel force may increase. KEMET recommends that maximum storage temperature not exceed 40ºC and maximum

storage humidity not exceed 70% relative humidity. Temperature ﬂuctuations should be minimized to avoid condensation on

the parts and atmospheres should be free of chlorine and sulfur bearing compounds. For optimized solderability chip stock

should be used promptly, preferably within 1.5 years of receipt.

C1008_X8L_150C_SMD • 11/29/2017 12

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

Construction – Standard Termination

Detailed Cross Section

Dielectric Material

(BaTiO₃)

Dielectric

Material (BaTiO₃)

Barrier Layer

(Ni)

Termination Finish

(100% Matte Sn /

SnPb - 5% Pb min)

End Termination/

External Electrode

(Cu)

Inner Electrodes

(Ni)

End Termination/

External Electrode

(Cu)

Barrier Layer

(Ni)

Termination Finish

(100% Matte Sn /

SnPb - 5% Pb min)

Inner Electrodes

(Ni)

Construction – Flexible Termination

Detailed Cross Section

Dielectric Material

(BaTiO₃)

Barrier Layer

(Ni)

End Termination/

External Electrode

(Cu)

Termination Finish

(100% Matte Sn /

SnPb - 5% Pb min)

Epoxy Layer

(Ag)

Dielectric

Material (BaTiO₃)

Inner Electrodes

(Ni)

End Termination/

External Electrode

(Cu)

Epoxy Layer

(Ag)

Barrier Layer

(Ni)

Termination Finish

(100% Matte Sn /

SnPb - 5% Pb min)

Inner Electrodes

(Ni)

C1008_X8L_150C_SMD • 11/29/2017 13

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

Capacitor Marking (Optional):

These surface mount multilayer ceramic capacitors are

normally supplied unmarked. If required, they can be

marked as an extra cost option. Marking is available

on most KEMET devices but must be requested using

the correct ordering code identiﬁer(s). If this option is

requested, two sides of the ceramic body will be laser

marked with a “K” to identify KEMET, followed by two

characters (per EIA–198 - see table below) to identify the

capacitance value. EIA 0603 case size devices are limited

to the “K” character only.

Marking appears in legible contrast. Illustrated below

is an example of an MLCC with laser marking of “KA8”,

which designates a KEMET device with rated capacitance

of 100 µF. Orientation of marking is vendor optional.

2-Digit

KEMET

Capacitance

ID

Code

Laser marking option is not available on:

• C0G, Ultra Stable X8R and Y5V dielectric devices.

• EIA 0402 case size devices.

• EIA 0603 case size devices with Flexible Termination

option.

• KPS Commercial and Automotive Grade stacked

devices.

• X7R dielectric products in capacitance values outlined

below.

EIA Case Size

Metric Size Code

Capacitance

0603

0805

1206

1210

1808

1812

1825

2220

2225

1608

2012

3216

3225

4520

4532

4564

5650

5664

≤ 170 pF

≤ 150 pF

≤ 910 pF

≤ 2,000 pF

≤ 3,900 pF

≤ 6,700 pF

≤ 0.018 µF

≤ 0.027 µF

≤ 0.033 µF

C1008_X8L_150C_SMD • 11/29/2017 14

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

Capacitor Marking (Optional) cont’d

Capacitance (pF) For Various Alpha/Numeral Identiﬁers

Numeral

Alpha

Character

9

0

1

2

3

4

5

6

7

8

Capacitance (pF)

A

B

C

D

E

F

0.10

0.11

0.12

0.13

0.15

0.16

0.18

0.20

0.22

0.24

0.27

0.30

0.33

0.36

0.39

0.43

0.47

0.51

0.56

0.62

0.68

0.75

0.82

0.91

0.25

0.35

0.40

0.45

0.50

0.60

0.70

0.80

0.90

1.0

1.1

1.2

1.3

1.5

1.6

1.8

2.0

2.2

2.4

2.7

3.0

3.3

3.6

3.9

4.3

4.7

5.1

5.6

6.2

6.8

7.5

8.2

9.1

2.5

3.5

4.0

4.5

5.0

6.0

7.0

8.0

9.0

10

11

12

13

15

16

18

20

22

24

27

30

33

36

39

43

47

51

56

62

68

75

82

91

25

35

40

45

50

60

70

80

90

100

110

120

130

150

160

180

200

220

240

270

300

330

360

390

430

470

510

560

620

680

750

820

910

250

350

400

450

500

600

700

800

900

1,000

1,100

1,200

1,300

1,500

1,600

1,800

2,000

2,200

2,400

2,700

3,000

3,300

3,600

3,900

4,300

4,700

5,100

5,600

6,200

6,800

7,500

8,200

9,100

2,500

3,500

4,000

4,500

5,000

6,000

7,000

8,000

9,000

10,000 100,000 1,000,000 10,000,000

11,000 110,000 1,100,000 11,000,000

100,000,000

110,000,000

120,000,000

130,000,000

150,000,000

160,000,000

180,000,000

200,000,000

220,000,000

240,000,000

270,000,000

300,000,000

330,000,000

360,000,000

390,000,000

430,000,000

470,000,000

510,000,000

560,000,000

620,000,000

680,000,000

750,000,000

820,000,000

910,000,000

250,000,000

350,000,000

400,000,000

450,000,000

500,000,000

600,000,000

700,000,000

800,000,000

900,000,000

12,000 120,000 1,200,000 12,000,000

13,000 130,000 1,300,000 13,000,000

15,000 150,000 1,500,000 15,000,000

16,000 160,000 1,600,000 16,000,000

18,000 180,000 1,800,000 18,000,000

20,000 200,000 2,000,000 20,000,000

22,000 220,000 2,200,000 22,000,000

24,000 240,000 2,400,000 24,000,000

27,000 270,000 2,700,000 27,000,000

30,000 300,000 3,000,000 30,000,000

33,000 330,000 3,300,000 33,000,000

36,000 360,000 3,600,000 36,000,000

39,000 390,000 3,900,000 39,000,000

43,000 430,000 4,300,000 43,000,000

47,000 470,000 4,700,000 47,000,000

51,000 510,000 5,100,000 51,000,000

56,000 560,000 5,600,000 56,000,000

62,000 620,000 6,200,000 62,000,000

68,000 680,000 6,800,000 68,000,000

75,000 750,000 7,500,000 75,000,000

82,000 820,000 8,200,000 82,000,000

91,000 910,000 9,100,000 91,000,000

25,000 250,000 2,500,000 25,000,000

35,000 350,000 3,500,000 35,000,000

40,000 400,000 4,000,000 40,000,000

45,000 450,000 4,500,000 45,000,000

50,000 500,000 5,000,000 50,000,000

60,000 600,000 6,000,000 60,000,000

70,000 700,000 7,000,000 70,000,000

80,000 800,000 8,000,000 80,000,000

90,000 900,000 9,000,000 90,000,000

G

H

J

K

L

M

N

P

Q

R

S

T

U

V

W

X

Y

Z

a

b

d

e

f

m

n

t

y

C1008_X8L_150C_SMD • 11/29/2017 15

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

Tape & Reel Packaging Information

KEMET offers multilayer ceramic chip capacitors packaged in 8, 12 and 16 mm tape on 7" and 13" reels in accordance with

EIA Standard 481. This packaging system is compatible with all tape-fed automatic pick and place systems. See Table 2 for

details on reeling quantities for commercial chips.

ꢑar code laꢈel

Antiꢆstatic reel

®

ꢇmꢈossed plasticꢉ or

punched paper carrierꢃ

Chip and ꢍꢎS orientation in pocꢌet

(eꢋcept 18ꢀ5 commercial, and 18ꢀ5 and ꢀꢀꢀ5 Military)

KEMET

Sprocꢌet holes

ꢇmꢈossment or punched cavity

8 mm, 1ꢀ mm

or 1ꢁ mm carrier tape

Antiꢆstatic cover tape

(0ꢃ10 mm (0ꢃ00ꢊꢄ) maꢋimum thicꢌness)

1ꢂ8 mm (ꢂꢃ00ꢄ)

or

ꢅꢅ0 mm (1ꢅꢃ00ꢄ)

ꢉꢇꢏA 01005, 0ꢀ01, 0ꢊ0ꢀ and 0ꢁ0ꢅ case siꢐes availaꢈle on punched paper carrier onlyꢃ

Table 5 – Carrier Tape Conﬁguration, Embossed Plastic & Punched Paper (mm)

New 2 mm Pitch Reel Options*

Embossed Plastic Punched Paper

Tape

Packaging

Ordering Code

(C-Spec)

C-3190

7" Reel 13" Reel 7" Reel 13" Reel

EIA Case Size Size

(W)*

Packaging Type/Options

Pitch (P₁)* Pitch (P₁)*

01005 – 0402

0603

8

2

2/4

4

Automotive grade 7" reel unmarked

Automotive grade 13" reel unmarked

Commercial grade 7" reel unmarked

Commercial grade 13" reel unmarked

C-3191

2/4

4

C-7081

0805

8

4

C-7082

1206 – 1210

1805 – 1808

≥ 1812

8

4

* 2 mm pitch reel only available for 0603 EIA case size.

2 mm pitch reel for 0805 EIA case size under development.

12

16

8

4

8

Beneﬁts of Changing from 4 mm to 2 mm Pitching Spacing

• Lower placement costs.

• Double the parts on each reel results in fewer reel

changes and increased eﬃciency.

• Fewer reels result in lower packaging, shipping and

storage costs, reducing waste.

KPS 1210

8

KPS 1812

and 2220

12

4

12

4

Array 0612

*Refer to Figures 1 and 2 for W and P₁carrier tape reference locations.

*Refer to Tables 6 and 7 for tolerance speciﬁcations.

C1008_X8L_150C_SMD • 11/29/2017 16

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

Figure 1 – Embossed (Plastic) Carrier Tape Dimensions

T

ꢀ ꢇ

ꢍ10 pitches cumulative

tolerance on tape ꢎ0ꢆꢇ mmꢏ

ꢇ

ꢉ

1

ꢀo

ꢈDo

Ao

ꢁ

ꢄo

ꢂ

ꢉ

ꢇ

ꢃ

1

ꢃo

S

1

ꢀ

1

T

1

ꢉmꢅossment

ꢁor cavity siꢊe,

see ꢋote 1 Taꢅle ꢌ

Center Lines of Cavity

ꢈD

1

Cover Tape

is for tape feeder reference only,

including draft concentric aꢅout ꢃoꢆ

ꢃ

1

User Direction of Unreeling

Table 6 – Embossed (Plastic) Carrier Tape Dimensions

Metric will govern

Constant Dimensions — Millimeters (Inches)

D₁Minimum

Note 1

1.0

(0.039)

R Reference S₁Minimum

T

T₁

Tape Size

8 mm

D₀

E₁

P₀

P₂

Note 2

Note 3

Maximum Maximum

25.0

(0.984)

1.5 +0.10/−0.0

(0.059 +0.004/−0.0)

1.75 ±0.10

4.0 ±0.10

2.0 ±0.05

0.600

(0.024)

0.600

(0.024)

0.100

(0.004)

12 mm

16 mm

(0.069 ±0.004) (0.157 ±0.004) (0.079 ±0.002)

1.5

(0.059)

30

(1.181)

Variable Dimensions — Millimeters (Inches)

B₁Maximum

Note 4

E₂

T₂

W

Tape Size

8 mm

Pitch

F

P₁

A₀,B₀& K₀

Minimum

6.25

(0.246)

Maximum Maximum

2.5

(0.098)

4.35

(0.171)

3.5 ±0.05

(0.138 ±0.002) (0.157 ±0.004)

4.0 ±0.10

8.3

(0.327)

Single (4 mm)

8.2

10.25

5.5 ±0.05

8.0 ±0.10

4.6

12.3

12 mm

16 mm

Note 5

and Double (8 mm)

(0.323)

(0.404)

(0.217 ±0.002) (0.315 ±0.004)

(0.181)

(0.484)

12.1

(0.476)

14.25

(0.561)

7.5 ±0.05 12.0 ±0.10

(0.138 ±0.002) (0.157 ±0.004)

4.6

(0.181)

16.3

(0.642)

Triple (12 mm)

1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment

location and hole location shall be applied independent of each other.

2. The tape with or without components shall pass around R without damage (see Figure 6).

3. If S₁< 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481 paragraph 4.3 section b).

4. B₁dimension is a reference dimension for tape feeder clearance only.

5. The cavity deﬁned by A₀, B₀and K₀shall surround the component with suﬃcient clearance that:

(a) the component does not protrude above the top surface of the carrier tape.

(b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.

(c) rotation of the component is limited to 20° maximum for 8 and 12 mm tapes and 10° maximum for 16 mm tapes (see Figure 3).

(d) lateral movement of the component is restricted to 0.5 mm maximum for 8 and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see

Figure 4).

(e) for KPS product, A₀and B₀are measured on a plane 0.3 mm above the bottom of the pocket.

(f) see addendum in EIA Standard 481 for standards relating to more precise taping requirements.

C1008_X8L_150C_SMD • 11/29/2017 17

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

Figure 2 – Punched (Paper) Carrier Tape Dimensions

T

ꢋ10 pitches cumulative

tolerance on tape ꢌ0ꢍꢄ mmꢎ

ꢂ₁

ꢀo

ꢁDo

A₀

ꢃ

ꢅ

ꢂ_ꢄ

ꢆ₀

ꢀ¹

ꢆottom Cover Tape

G

Cavity Siꢇe,

See

T¹

Center Lines of Cavity

Top Cover Tape

ꢈote 1, Taꢉle ꢊ

ꢆottom Cover Tape

User Direction of Unreeling

Table 7 – Punched (Paper) Carrier Tape Dimensions

Metric will govern

Constant Dimensions — Millimeters (Inches)

R Reference

Note 2

Tape Size

8 mm

D₀

E₁

P₀

P₂

T₁Maximum

G Minimum

0.10

1.5 +0.10 -0.0

(0.059 +0.004 -0.0)

1.75 ±0.10

(0.069 ±0.004)

4.0 ±0.10

(0.157 ±0.004)

2.0 ±0.05

(0.079 ±0.002)

0.75

(0.030)

25

(0.984)

(0.004)

Maximum

Variable Dimensions — Millimeters (Inches)

Tape Size

8 mm

Pitch

E2 Minimum

F

P₁

T Maximum

W Maximum

A₀B₀

2.0 ±0.05

(0.079 ±0.002)

4.0 ±0.10

(0.157 ±0.004)

8.3

(0.327)

8.3

(0.327)

Half (2 mm)

Single (4 mm)

6.25

(0.246)

3.5 ±0.05

(0.138 ±0.002)

1.1

(0.098)

Note 1

8 mm

1. The cavity deﬁned by A₀, B₀and T shall surround the component with suﬃcient clearance that:

a) the component does not protrude beyond either surface of the carrier tape.

b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.

c) rotation of the component is limited to 20° maximum (see Figure 3).

d) lateral movement of the component is restricted to 0.5 mm maximum (see Figure 4).

e) see addendum in EIA Standard 481 for standards relating to more precise taping requirements.

2. The tape with or without components shall pass around R without damage (see Figure 6).

C1008_X8L_150C_SMD • 11/29/2017 18

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

Packaging Information Performance Notes

1. Cover Tape Break Force: 1.0 kg minimum.

2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be:

Tape Width

8 mm

Peel Strength

0.1 to 1.0 Newton (10 to 100 gf)

0.1 to 1.3 Newton (10 to 130 gf)

12 and 16 mm

The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be

165° to 180° from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of

300 ±10 mm/minute.

3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA

Standards 556 and 624.

Figure 3 – Maximum Component Rotation

°

T

Maximum Component Rotation

Top View

Maximum Component Rotation

Side View

Typical Pocket Centerline

Tape

Maximum

°

T

s

Width (mm) Rotation (

)

8,12

16 – 200

20

10

Bo

Tape

Maximum

°

S

Width (mm) Rotation (

)

8,12

16 – 56

72 – 200

20

10

5

Typical Component Centerline

Ao

Figure 4 – Maximum Lateral Movement

Figure 5 – Bending Radius

Embossed

Carrier

Punched

Carrier

8 mm & 12 mm Tape

16 mm Tape

0.5 mm maximum

1.0 mm maximum

R

Bending

Radius

R

C1008_X8L_150C_SMD • 11/29/2017 19

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

Figure 6 – Reel Dimensions

ꢁull ꢂadius,

ꢌꢍ (ꢆncludes

flange distortion

at outer edge)

Access Hole at

Slot Location

(ꢄ ꢅ0 mm minimum)

See ꢀote

ꢌꢈ (Measured at huꢎ)

D

(See ꢀote)

A

ꢀ

C

(Arꢎor hole

ꢌ1 (Measured at huꢎ)

diameter)

ꢆf present,

tape slot in core

for tape startꢇ

ꢈꢉ5 mm minimum ꢊidth ꢋ

10ꢉ0 mm minimum depth

ꢃ

(see ꢀote)

ꢀoteꢇ Drive spoꢏes optionalꢐ if used, dimensions ꢃ and D shall applyꢉ

Table 8 – Reel Dimensions

Metric will govern

Constant Dimensions — Millimeters (Inches)

Tape Size

8 mm

A

B Minimum

C

D Minimum

178 ±0.20

(7.008 ±0.008)

or

1.5

(0.059)

13.0 +0.5/−0.2

(0.521 +0.02/−0.008)

20.2

(0.795)

12 mm

16 mm

330 ±0.20

(13.000 ±0.008)

Variable Dimensions — Millimeters (Inches)

Tape Size

8 mm

N Minimum

W₁

W₂Maximum

W₃

8.4 +1.5/−0.0

(0.331 +0.059/−0.0)

14.4

(0.567)

50

(1.969)

12.4 +2.0/−0.0

18.4

Shall accommodate tape

width without interference

12 mm

16 mm

(0.488 +0.078/−0.0)

(0.724)

16.4 +2.0/−0.0

(0.646 +0.078/−0.0)

22.4

(0.882)

C1008_X8L_150C_SMD • 11/29/2017 20

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

Figure 7 – Tape Leader & Trailer Dimensions

ꢃmꢈossed Carrier

Carrier Tape

ꢇunched Carrier

8 mm & 1ꢅ mm only

ꢁound Sprocꢂet Holes

START

END

Top Cover Tape

ꢃlongated Sprocꢂet Holes

(ꢄꢅ mm tape and ꢆider)

100 mm

minimum Leader

ꢉ00 mm minimum

Trailer

Components

1ꢀ0 mm minimum

Top Cover Tape

Figure 8 – Maximum Camber

ꢃlongated Sprocꢁet Holes

(ꢅꢄ mm & ꢆider tapes)

Carrier Tape

ꢀound Sprocꢁet Holes

1 mm maꢂimum, either direction

Straight ꢃdge

ꢄ50 mm

C1008_X8L_150C_SMD • 11/29/2017 21

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Temperature 150°C, X8L Dielectric, 10 – 50 VDC (Commercial & Automotive Grade)

KEMET Electronics Corporation Sales Oﬃces

For a complete list of our global sales oﬃces, please visit www.kemet.com/sales.

Disclaimer

All product speciﬁcations, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for

checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.

All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.

Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such

applications, but are not intended to constitute – and KEMET speciﬁcally disclaims – any warranty concerning suitability for a speciﬁc customer application or use.

The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any

technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no

obligation or liability for the advice given or results obtained.

Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component

failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards

(such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or

property damage.

Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other

measures may not be required.

KEMET is a registered trademark of KEMET Electronics Corporation.

C1008_X8L_150C_SMD • 11/29/2017 22


型号：	C1210C475K3NACTU
厂家：	KEMET CORPORATION
描述：	Ceramic Capacitor, Multilayer, Ceramic, 25V, 10% +Tol, 10% -Tol, X8L, -40/+15% TC, 4.7uF, Surface Mount, 1210, CHIP 电容器
文件：	总22页 (文件大小：1522K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

C1210C475K3NACTU [KEMET]

相关型号：

C1210C475K3PAC3325

C1210C475K3PAC7025

C1210C475K3PACTU

C1210C475K3RAC

C1210C475K3RAC7210

C1210C475K3RACTU

C1210C475K4PAC7025

C1210C475K4PACTU

C1210C475K4RAC

C1210C475K4RACTM

C1210C475K4RACTU

C1210C475K5R1C7186