A720V567M002APE003 [KEMET]
A720, Polymer Aluminum, 560 uF, 20%, 2 VDC, -55/+105°C, Height Max = 2.1mm;
| 型号： | A720V567M002APE003 |
| 厂家： | 
KEMET CORPORATION |
| 描述： | A720, Polymer Aluminum, 560 uF, 20%, 2 VDC, -55/+105°C, Height Max = 2.1mm |
| 文件： | 总15页 (文件大小：1348K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Aluminum Organic Capacitor (AO-CAP)
A720 Polymer Aluminum
Overview
The KEMET Aluminum Organic Capacitor (AO-CAP)
is a solid state aluminum capacitor. The cathode is a
conductive organic polymer, which results in very low ESR
and improved capacitance retention at a high frequency.
AO-CAPs may be operated at steady state voltages up
to100% of rated voltage without the need to de-rate.
Since there is no liquid electrolyte, the A720 offers long
operational lifetimes, low ESR and high operational
temperatures. The inherent low ESR renders the A720
suitable for high ripple current handling. The small
package size, high ripple current capability, high operating
temperature, low parasistics, and high capacitance make the
A720 ideal for high performance microprocessor, FPGA, and
ASIC decoupling designs.
Benefits
• Polymer cathode technology
• High frequency capacitance retention
• Non-ignition failure mode
• 100% accelerated steady state aging
• 100% surge current tested
•ꢀ Volumetricꢀefficiency
•ꢀ MinimumꢀESRꢀupꢀtoꢀmΩ
• Voltage: 2 – 35 V
•ꢀ Capacitance:ꢀ22ꢀ–ꢀ470ꢀμF
Click image above for interactive 3D content
Open PDF in Adobe Reader for full functionality
Applications
Typical applications include DC/DC converters, notebook PCs, telecommunications, displays, and industrial applications.
Environmental Compliance
RoHS Compliant (6/6) according to Directive 2002/95/EC when ordered with Ni-Pd-Au.
K-SIM
Forꢀaꢀdetailedꢀanalysisꢀofꢀspecificꢀpartꢀnumbers,ꢀpleaseꢀvisitꢀksim.kemet.comꢀtoꢀaccessꢀKEMET'sꢀK-SIMꢀsoftware.ꢀKEMETꢀ
K-SIM is designed to simulate behavior of components with respect to frequency, ambient temperature, and DC bias levels.
One world. One KEMET
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
T2078_A720 • 3/17/2020
1
Aluminum Organic Capacitor (AO-CAP)
A720 Polymer Aluminum
Ordering Information
A
720
V
477
M
002
A
P
E003
Capacitor
Class
Case Capacitance Code Capacitance Rated Voltage Failure Rate/ Termination
Packaging
(C-Spec)
Series
ESR
Size
(pF)
Tolerance
(VDC)
Design
Finish
A =
720 =
V
First two digits
represent
significantꢀ
figures.ꢀThirdꢀ
digitꢀspecifiesꢀ
number of zeros.
M =
±20%
002 = 2
2R5 = 2.5
035 = 35
A =
N/A
P =
Ni-Pd-Au
E = ESR
Last three
digits specify
ESRꢀinꢀmΩꢀ
(018ꢀ=ꢀ18ꢀmΩ)
Blank = 7" Reel
7280 = 13" Reel
Aluminum Aluminum
Polymer
(Gen II)
Performance Characteristics
Item
Performance Characteristics
Operating Temperature
Rated Capacitance Range
Capacitance Tolerance
Rated Voltage Range
DF (120 Hz)
−55°Cꢀtoꢀ105°C
22ꢀ–ꢀ470ꢀμFꢀatꢀ120ꢀHz/25°C
M Tolerance (20%)
2 – 35 V
ReferꢀtoꢀPartꢀNumberꢀElectricalꢀSpecificationꢀTableꢀ
ReferꢀtoꢀPartꢀNumberꢀElectricalꢀSpecificationꢀTableꢀ
ESR (100 kHz)
ReferꢀtoꢀPartꢀNumberꢀElectricalꢀSpecificationꢀTable
If there is any concern about leakage current, please perform pre-conditioning to the part
following below conditions:
*ꢀTemperature:ꢀ105°Cꢀmaximum
* Voltage: Rated Voltage
Leakage Current
*ꢀSeriesꢀResistor:ꢀ1,000ꢀΩ
* Charge Time: 1 hour minimum
* Measuring: Discharge the capacitor(s), store them for 4 to 24 hours at room temperature
andꢀRHꢀ≤ꢀ60%
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
T2078_A720 • 3/17/2020
2
Aluminum Organic Capacitor (AO-CAP)
A720 Polymer Aluminum
Qualification
Test
Condition
Characteristics
Withinꢀ±10%ꢀofꢀinitialꢀvalueꢀ(forꢀ≤ꢀ16ꢀVꢀparts)
Withinꢀ±20%ꢀofꢀinitialꢀvalueꢀ(forꢀ≥ꢀ16ꢀVꢀparts)
ΔꢀC/C
DF
≤ꢀinitialꢀlimit
Endurance
105°Cꢀatꢀ1.0ꢀVR, 2,000 hours
DCL
ESR
Withinꢀ1.25ꢀxꢀinitialꢀlimit
Withinꢀ2.0ꢀxꢀinitialꢀlimit
Withinꢀ±10%ꢀofꢀinitialꢀvalueꢀ(forꢀ≤ꢀ16ꢀVꢀparts)
Withinꢀ±20%ꢀofꢀinitialꢀvalueꢀ(forꢀ≥ꢀ16ꢀVꢀparts)
ΔꢀC/C
DF
DCL
ESR
ΔꢀC/C
DF
Within initial limits
Storage Life
Humidity
105°Cꢀatꢀ0ꢀvolts,ꢀ2,000ꢀhours
Withinꢀ1.25ꢀxꢀinitialꢀlimit
Withinꢀ2.0ꢀxꢀinitialꢀlimit
Withinꢀ−20/+50%ꢀofꢀinitialꢀvalue
Withinꢀ2.0ꢀxꢀinitialꢀlimit
Withinꢀ5.0ꢀxꢀinitialꢀlimit
60°C,ꢀ90%ꢀRH,ꢀ500ꢀhours,ꢀnoꢀload
DCL
+25°C
IL*
−55°C
±15%
IL
+85°C
±15%
IL
+105°C
±20%
IL
Extremeꢀtemperatureꢀexposureꢀatꢀaꢀ
successionꢀofꢀcontinuousꢀstepsꢀatꢀ+25°C,ꢀ
−55°C,ꢀ+25°C,ꢀ+85°C,ꢀ+105°C,ꢀ+25°C
ΔꢀC/C
DF
Temperature
Stability
IL
DCL
IL
N/A
2ꢀxꢀIL
2ꢀxꢀIL
Withinꢀ±10%ꢀofꢀinitialꢀvalueꢀ(forꢀ≤ꢀ16ꢀVꢀparts)
Withinꢀ±20%ꢀofꢀinitialꢀvalueꢀ(forꢀ≥ꢀ16ꢀVꢀparts)
ΔꢀC/C
105°C,ꢀ1.32ꢀxꢀRatedꢀVoltage,ꢀ33ꢀΩꢀresistance,
1,000 cycles
DF
Within initial limits
Within initial limits
Within initial limits
Surge Voltage
DCL
ESR
Withinꢀ±10%ꢀofꢀinitialꢀvalueꢀ(forꢀ≤ꢀ16ꢀVꢀparts)
Withinꢀ±20%ꢀofꢀinitialꢀvalueꢀ(forꢀ≥ꢀ16ꢀVꢀparts)
ΔꢀC/C
MIL–STD–202, Method 213, Condition I, 100 G Peak
MIL–STD–202, Method 204, Condition D,
10 Hz to 2,000 Hz, 20 G Peak
Mechanical Shock/
Vibration
DF
Within initial limits
Within initial limits
DCL
*IL = Initial Limit
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
T2078_A720 • 3/17/2020
3
Aluminum Organic Capacitor (AO-CAP)
A720 Polymer Aluminum
Electrical Characteristics
ESR vs. Frequency
100
10
A720V477M002_IMP
A720V477M002_ESR
A720V226M035_IMP
A720V226M035_ESR
1
0.1
0.01
0.001
100
1,000
10,000
100,000
1,000,000
Frequency (Hz)
Capacitance vs. Frequency
1,000
100
10
A720V477M002_CAP
A720V226M035_CAP
1
100
1,000
10,000
100,000
1,000,000
Frequency (Hz)
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
T2078_A720 • 3/17/2020
4
Aluminum Organic Capacitor (AO-CAP)
A720 Polymer Aluminum
Dimensions – Millimeters (Inches)
Metric will govern
BOTTOM VIEW
END VIEW
SIDE VIEW
F
w
H
L
S
S
F ±0.1
±(0.004) ±(0.012)
S ±0.3
KEMET
EIA
L
W
H
Weight
7.3±0.3
4.3±0.3
1.9±0.2
7343–21
2.4 (0.094)
1.3 (0.051)
141.00
V
(0.287±0.012) (0.169±0.012) (0.075±0.008)
Notes: (Ref) – Dimensions provided for reference only.
These weights are provide as reference. If exact weights are needed, please contact your KEMET Sale Representative.
Table 1 – Ratings & Part Number Reference
Ripple
Current
(rms)
Maximum
MSL Operating
Temp.
Rated
Rated
Case Code/
KEMET Part
Number
DC
Leakage
DF
ESR
Voltage Capacitance Case Size
µA at +25°C
Maximum/5
Minutes
% at +25°C
120 Hz
Maximum
mΩ at 25°C
100 kHz
Maximum
mA at 100 kHz
with/T = +20°C at
−55°C to 105°C
(See below for
part options)
Reflow Temp
°C
VDC at 105°C
µF
KEMET/EIA
≤ 260°C
2
2
2
2.5
2.5
4
470
470
470
470
470
330
330
330
330
100
100
100
100
22
V/7343-21
V/7343-21
V/7343-21
V/7343-21
V/7343-21
V/7343-21
V/7343-21
V/7343-21
V/7343-21
V/7343-21
V/7343-21
V/7343-21
V/7343-21
V/7343-21
A720V477M002APE006
A720V477M002APE4R5
A720V477M002APE003
A720V477M2R5APE4R5
A720V477M2R5APE003
A720V337M004APE006
A720V337M004APE4R5
A720V337M004APE003
A720V337M006APE4R5
A720V107M016APE040
A720V107M016APE025
A720V107M016APE015
A720V107M016APE010
A720V226M035APE040
56.4
56.4
56.4
70.5
70.5
79.2
79.2
79.2
83.2
160
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4.5
3
4.5
3
6
4.5
3
4.5
40
25
15
10
40
8,260
9,540
11,690
9,540
11,690
8,260
9,540
11,690
9,540
3,200
4,000
5,200
6,400
3,200
3
3
3
3
3
3
3
3
3
3
3
3
3
3
105
105
105
105
105
105
105
105
105
105
105
105
105
105
4
4
6.3
16
16
16
16
35
160
160
160
30.8
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
T2078_A720 • 3/17/2020
5
Aluminum Organic Capacitor (AO-CAP)
A720 Polymer Aluminum
Derating Guidelines
Maximum
Maximum
Recommended
Transient Voltage
Recommended
Steady State
Voltage
Voltage Rating
−55°Cꢀtoꢀ105°C
2 – 35 V
VR
VR
VR = Rated Voltage
Ripple Current/Ripple Voltage
Permissible AC ripple voltage and current are related to equivalent series resistance (ESR) and the power dissipation
capabilities of the device. Permissible AC ripple voltage, which may be applied, is limited by two criteria:
ꢀ 1.ꢀTheꢀpositiveꢀpeakꢀACꢀvoltageꢀplusꢀtheꢀDCꢀbiasꢀvoltage,ꢀifꢀany,ꢀmustꢀnotꢀexceedꢀtheꢀDCꢀvoltageꢀratingꢀofꢀtheꢀcapacitor.
ꢀ 2.ꢀTheꢀnegativeꢀpeakꢀACꢀvoltage,ꢀinꢀcombinationꢀwithꢀbiasꢀvoltage,ꢀifꢀany,ꢀmustꢀnotꢀexceedꢀtheꢀallowableꢀlimitsꢀspecifiedꢀ
for reverse voltage. See the Reverse Voltage section for allowable limits.
Powerꢀcapabilityꢀisꢀdeterminedꢀbasedꢀonꢀaꢀ20°Cꢀtemperatureꢀrise.ꢀAꢀhigherꢀtemperatureꢀriseꢀandꢀthereforeꢀhigherꢀpowerꢀ
capabilityꢀisꢀallowableꢀasꢀlongꢀasꢀtheꢀambientꢀtemperature,ꢀplus,ꢀtemperatureꢀriseꢀdueꢀtoꢀrippleꢀcurrent,ꢀdoesꢀnotꢀexceedꢀtheꢀ
rated temperature of the part.
Theꢀmaximumꢀpowerꢀdissipationꢀbyꢀcaseꢀsizeꢀcanꢀbeꢀdeterminedꢀusingꢀtheꢀbelowꢀtable.
Maximum Power
KEMET Series
and Case Code
EIA
Case Code
Dissipation (Pmax)
mWatts at 25°C
with +20°C Rise
410
A720V
7343–21
UsingꢀtheꢀPmaxꢀofꢀtheꢀdevice,ꢀtheꢀmaximumꢀallowableꢀRMSꢀrippleꢀcurrentꢀorꢀvoltageꢀmayꢀbeꢀdetermined.
I(max) = √Pmax/R
E(max) = Z √Pmax/R
I = RMS ripple current (amperes)
E = RMS ripple voltage (volts)
Pmax = Maximum power dissipation(watts)
R = ESR at specified frequency (ohms)
Z = Impedance at specified frequency (Ohms)
Refer to part number listings for permittable Arms limits.
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
T2078_A720 • 3/17/2020
6
Aluminum Organic Capacitor (AO-CAP)
A720 Polymer Aluminum
Reverse Voltage
Polymer aluminum capacitors are polar devices and may be permanently damaged or destroyed if connected in the wrong
polarity. These devices will withstand a certain degree of transient voltage reversal for short periods, as shown in the below
table. Please note that these parts may not be operated continuously in reverse, even within these limits.
Temperature
Permissible Transient Reverse Voltage
25°C
55°C
85°C
105°C
60% of rated voltage
50% of rated voltage
40% of rated voltage
30% of rated voltage
Table 2 – Land Dimensions/Courtyard
Metric
Size
Code
Density Level A:
Maximum (Most) Land
Protrusion (mm)
Density Level B:
Median (Nominal) Land
Protrusion (mm)
Density Level C:
Minimum (Least) Land
Protrusion (mm)
KEMET
Case
EIA
W
L
S
V1
V2
W
L
S
V1
V2
W
L
S
V1
V2
V
7343–21 2.55
2.77
3.67 10.22 5.60
2.43
2.37
3.87
9.12
5.10
2.33
1.99
4.03
8.26
4.84
Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder
processes.
Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes.
Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform
qualification testing based on the conditions outlined in IPC standard 7351 (IPC–7351).
¹ Height of these chips may create problems in wave soldering.
2 Land pattern geometry is too small for silkscreen outline.
V1
L
L
V2
W
W
S
Grid Placement Courtyard
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
T2078_A720 • 3/17/2020
7
Aluminum Organic Capacitor (AO-CAP)
A720 Polymer Aluminum
Soldering Process
Pb-Free
Profile Feature
SnPb Assembly
Assembly
The KEMET families of surface mount capacitors are
compatible with wave (single or dual), convection, IR,
orꢀvaporꢀphaseꢀreflowꢀtechniques.ꢀPreheatingꢀofꢀtheseꢀ
componentsꢀisꢀrecommendedꢀtoꢀavoidꢀextremeꢀthermalꢀ
stress.ꢀKEMET'sꢀrecommendedꢀprofileꢀconditionsꢀforꢀ
convectionꢀandꢀIRꢀreflowꢀreflectꢀtheꢀprofileꢀconditionsꢀofꢀtheꢀ
IPC/J-STD-020D standard for moisture sensitivity testing.
Theꢀdevicesꢀcanꢀsafelyꢀwithstandꢀaꢀmaximumꢀofꢀthreeꢀreflowꢀ
passes at these conditions.
Preheat/Soak
Temperature Minimum (TSmin
)
100°C
150°C
TemperatureꢀMaximumꢀ(TSmax
)
150°C
200°C
Time (ts) from Tsmin to Tsmax
Ramp-up Rate (TL to TP)
)
60 – 120 seconds
60 – 120 seconds
3°C/secondsꢀmaximum 3°C/secondsꢀmaximum
Liquidous Temperature (TL)
Time Above Liquidous (tL)
183°C
217°C
60 – 150 seconds
60 – 150 seconds
220°C*ꢀ
235°C**
250°C*
260°C**
Peak Temperature (TP)
Timeꢀwithinꢀ5°CꢀofꢀMaximumꢀ
20ꢀsecondsꢀmaximum 30ꢀsecondsꢀmaximum
Peak Temperature (tP)
Ramp-down Rate (TP to TL) 6°C/secondsꢀmaximum 6°C/secondsꢀmaximum
Notes:
Timeꢀ25°CꢀtoꢀPeakꢀ
Temperature
Hand soldering leads to risk of damage. If performed use
tweezers to hold both capacitors terminals followed by
weldingꢀprocedure.ꢀAvoidꢀexcessiveꢀforceꢀandꢀtouchingꢀ
capacitor body while soldering. Once the capacitor is
removed from the board should not be weld again.
6ꢀminutesꢀmaximum
8ꢀminutesꢀmaximum
Note: All temperatures refer to the center of the package, measured on the
package body surface that is facing up during assembly reflow.
* For Case Size height > 2.5 mm
** For Case Size height ≤ 2.5 mm
ꢀP
tP
ꢅaꢃimum ꢆamp-up ꢆate ꢇ ꢈꢉCꢊꢁeconꢋ
ꢅaꢃimum ꢆamp-ꢋoꢌn ꢆate ꢇ ꢍꢉCꢊꢁeconꢋ
ꢀꢄ
tꢄ
ꢀꢁmaꢃ
ꢀꢁmin
tꢁ
2ꢂ
2ꢂꢉC to Peaꢎ
Time
Storage
AllꢀAO-CAPꢀSeriesꢀareꢀshippedꢀinꢀmoistureꢀbarrierꢀbagsꢀ(MBBs)ꢀwithꢀdesiccantꢀand humidityꢀindicatorꢀcardꢀ(HIC).ꢀTheseꢀ
partsꢀareꢀclassified asꢀMSL3ꢀ(MoistureꢀSensitivityꢀLevelꢀ3)ꢀperꢀIPC/JEDECꢀJ-STD-020ꢀandꢀpackagedꢀper
IPC/JEDECꢀJ-STD-033.ꢀMSL3ꢀspecifiesꢀaꢀfloorꢀtimeꢀofꢀ168Hꢀatꢀ30°Cꢀmaximumꢀtemperature andꢀ60%ꢀrelativeꢀhumidity.ꢀ
Unused capacitors should be sealed in a MBB with fresh desiccant.
Theꢀcalculatedꢀshelfꢀlifeꢀinꢀaꢀsealedꢀbagꢀwouldꢀbeꢀ12ꢀmonthsꢀfromꢀaꢀbagꢀsealꢀdateꢀinꢀaꢀstorageꢀenvironmentꢀofꢀ<ꢀ40°Cꢀandꢀ
humidityꢀ<ꢀ90%ꢀRH.ꢀItꢀshouldꢀbeꢀ24ꢀmonthsꢀfromꢀaꢀbagꢀsealꢀdateꢀinꢀaꢀstorageꢀenvironmentꢀofꢀ<ꢀ30°Cꢀandꢀhumidityꢀ<ꢀ70%ꢀRH.
If baking is required, refer to IPC/JEDEC J-STD-033 for bake procedure..
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
T2078_A720 • 3/17/2020
8
Aluminum Organic Capacitor (AO-CAP)
A720 Polymer Aluminum
Construction
Molded Epoxy
Case
Detailed Element Layer View
Polarity Stripe (+)
Leadframe
(+ Anode)
Silver Epoxy
Leadframe
(− Cathode)
Molded Epoxy
Case
Capacitor Marking
Date Code *
Year
Week
Polarity
Indicator (+)
H = 2017
I = 2018
J = 2019
K = 2020
01 = 1st week of the year to
52 = 52nd week of the year
Picofarad
Code
KEMET
ID
Rated
Voltage
Date
Code*
* H07 = 7th week of 2017
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
T2078_A720 • 3/17/2020
9
Aluminum Organic Capacitor (AO-CAP)
A720 Polymer Aluminum
Tape & Reel Packaging Information
KEMET’s molded chip capacitor families are packaged in 8 and 12 mm plastic tape on 7" and 13" reels in accordance with
EIA Standard 481: Embossed Carrier Taping of Surface Mount Components for Automatic Handling. This packaging system
is compatible with all tape-fed automatic pick-and-place systems.
ꢋigꢌt ꢌanꢊ
orientation
only
ꢀmꢁoꢂꢂeꢊ carrier
(ꢍ)
(−)
ꢀmꢁoꢂꢂment
ꢎop tape tꢌicꢏneꢂꢂ
0ꢄꢆ0 mm (0ꢄ00ꢉꢈ)
maꢐimum tꢌicꢏneꢂꢂ
ꢃ mm (0ꢄꢅꢆꢇꢈ) or
ꢆ2 mm (0ꢄꢉ72ꢈ)
ꢆꢃ0 mm (7ꢄ0ꢈ) or
ꢅꢅ0 mm (ꢆꢅꢄꢈ)
Table 3 – Packaging Quantity
Tape Width
Case Code
7" Reel* 13" Reel*
(mm)
KEMET
V
EIA
7343-21
12
1,000
3,000
* No C-Spec required for 7" reel packaging. C-7280 required for 13" reel packaging.
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
T2078_A720 • 3/17/2020 10
Aluminum Organic Capacitor (AO-CAP)
A720 Polymer Aluminum
Figure 1 – Embossed (Plastic) Carrier Tape Dimensions
ꢀ
ꢀ2
P2
(ꢉ0 pitcꢕeꢄ cumulatiꢆe
tolerance on tape ꢖ0ꢍ2 mm)
ꢑꢉ
P0
ꢎꢏ0
A0
ꢁ
ꢈ0
ꢂ
ꢑ2
ꢇꢉ
ꢇ0
ꢐꢉ
Pꢉ
ꢀꢉ
Coꢆer ꢀape
ꢑmꢌoꢄꢄment
ꢁor caꢆity ꢄiꢒeꢋ
ꢄee ꢓote ꢉꢋ ꢀaꢌle ꢔ
Center ꢃineꢄ oꢅ Caꢆity
ꢎꢏꢉ
ꢇꢉ iꢄ ꢅor tape ꢅeeꢊer reꢅerence onlyꢋ
incluꢊing ꢊraꢅt concentric aꢌout ꢇ0ꢍ
ꢀꢁer Direꢂꢃion oꢄ ꢀnreeling
Table 4 – Embossed (Plastic) Carrier Tape Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
D1 Minimum
Note 1
R Reference S1 Minimum
T1
Tape Size
8 mm
D0
E1
P0
P2
TꢀMaximum
Note 2
Note 3
Maximum
1.0
(0.039)
25.0
(0.984)
1.5ꢀ+0.10/−0.0ꢀ
1.75 ±0.10
4.0 ±0.10
2.0 ±0.05
0.600
0.600
0.100
(0.059ꢀ+0.004/−0.0)
(0.069 ±0.004) (0.157 ±0.004) (0.079 ±0.002)
(0.024)
(0.024)
(0.004)
1.5
(0.059)
30
(1.181)
12 mm
Variable Dimensions — Millimeters (Inches)
B1ꢀMaximumꢀ
Tape Size
8 mm
Pitch
E2 Minimum
F
P1
T2ꢀMaximum WꢀMaximum A0, B0 & K0
Note 4
4.35
(0.171)
6.25
(0.246)
3.5 ±0.05
2.0 ±0.05 or 4.0 ±0.10
2.5
8.3
(0.327)
Single (4 mm)
(0.138 ±0.002) (0.079 ±0.002 or 0.157 ±0.004)
(0.098)
Note 5
Single (4 mm)
and Double
(8 mm)
2.0 ±0.05 (0.079 ±0.002) or
8.2
(0.323)
10.25
(0.404)
5.5 ±0.05
4.6
(0.181)
12.3
(0.484)
12 mm
4.0 ±0.10 (0.157 ±0.004) or
(0.217 ±0.002)
8.0 ±0.10 (0.315 ±0.004)
1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment
location and hole location shall be applied independent of each other.
2. The tape, with or without components, shall pass around R without damage (see Figure 4).
3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481–D, paragraph 4.3, section b).
4. B1 dimension is a reference dimension for tape feeder clearance only.
5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that:
(a) the component does not protrude above the top surface of the carrier tape.
(b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
(c) rotation of the component is limited to 20° maximum for 8 and 12 mm tapes (see Figure 2).
(d) lateral movement of the component is restricted to 0.5 mm maximum for 8 mm and 12 mm wide tape (see Figure 3).
(e) see Addendum in EIA Standard 481–D for standards relating to more precise taping requirements.
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
T2078_A720 • 3/17/2020 11
Aluminum Organic Capacitor (AO-CAP)
A720 Polymer Aluminum
Packaging Information Performance Notes
1. Cover tape break force: 1.0 kg minimum.
2. Cover tape peel strength: The total peel strength of the cover tape from the carrier tape shall be:
Tape Width
8 mm
Peel Strength
0.1 to 1.0 newton (10 to 100 gf)
0.1 to 1.3 newton (10 to 130 gf)
12 mm
The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be
165°ꢀtoꢀ180°ꢀfromꢀtheꢀplaneꢀofꢀtheꢀcarrierꢀtape.ꢀDuringꢀpeeling,ꢀtheꢀcarrierꢀand/orꢀcoverꢀtapeꢀshallꢀbeꢀpulledꢀatꢀaꢀvelocityꢀofꢀ
300 ±10 mm/minute.
3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA
Standards 556 and 624.
Figure 2 – Maximum Component Rotation
°
ꢁ
Maximum ꢀomponenꢁ ꢂoꢁaꢁion
Top View
Maximum ꢀomponenꢁ ꢂoꢁaꢁion
Siꢃe View
ꢁypical Pocꢇet Centerline
Tape
Wiꢃꢁꢄ ꢅmmꢆ
ꢃꢄ ꢅ2
Maximum
ꢂoꢁaꢁion ꢅ
20
°
°
ꢁ
ꢂ
)
ꢀo
Tape
Wiꢃꢁꢄ ꢅmmꢆ
ꢃꢄ ꢅ2
Maximum
ꢂoꢁaꢁion ꢅ
20
°
ꢆ
)
ꢁypical Component Centerline
Ao
Figure 4 – Bending Radius
Figure 3 – Maximum Lateral Movement
ꢄmꢅoꢃꢃeꢂ
Carrier
Puncꢆeꢂ
Carrier
ꢃ mm ꢄ ꢅ2 mm ꢆape
0ꢀꢁ mm maꢂimum
0ꢀꢁ mm maꢂimum
ꢀ
ꢁenꢂing
ꢀaꢂiuꢃ
ꢀ
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
T2078_A720 • 3/17/2020 12
Aluminum Organic Capacitor (AO-CAP)
A720 Polymer Aluminum
Figure 5 – Reel Dimensions
ꢃull ꢄaꢅiuꢆꢇ
ꢁee ꢂote
ꢖꢗ (ꢍncluꢅeꢆ
ꢎlange ꢅiꢆtortion
at outer eꢅge)
Acceꢆꢆ ꢉole at
ꢁlot ꢊocation
(ꢋ ꢌ0 mm minimum)
ꢖ2 (ꢘeaꢆureꢅ at ꢓuꢙ)
ꢀ
(ꢁee ꢂote)
A
ꢂ
C
(Arꢙor ꢓole
ꢖꢕ (ꢘeaꢆureꢅ at ꢓuꢙ)
ꢅiameter)
ꢍꢎ preꢆentꢇ
tape ꢆlot in core
ꢎor tape ꢆtartꢏ
2ꢐꢑ mm minimum ꢒiꢅtꢓ ꢔ
ꢕ0ꢐ0 mm minimum ꢅeptꢓ
ꢈ
(ꢆee ꢂote)
ꢂoteꢏ ꢀriꢚe ꢆpoꢛeꢆ optionalꢜ iꢎ uꢆeꢅꢇ ꢅimenꢆionꢆ ꢈ anꢅ ꢀ ꢆꢓall applyꢐ
Table 5 – Reel Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
Tape Size
8 mm
A
B Minimum
C
D Minimum
178 ±0.20
(7.008 ±0.008)
or
1.5
(0.059)
13.0ꢀ+0.5/−0.2ꢀ
(0.521ꢀ+0.02/−0.008)
20.2
(0.795)
12 mm
330 ±0.20
(13.000 ±0.008)
Variable Dimensions — Millimeters (Inches)
Tape Size
8 mm
N Minimum
W1
W2ꢀMaximum
W3
8.4ꢀ+1.5/−0.0
(0.331ꢀ+0.059/−0.0)
12.4ꢀ+2.0/−0.0
14.4
(0.567)
18.4
50
(1.969)
Shall accommodate tape
width without interference
12 mm
(0.488ꢀ+0.078/−0.0)ꢀꢀ
(0.724)
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
T2078_A720 • 3/17/2020 13
Aluminum Organic Capacitor (AO-CAP)
A720 Polymer Aluminum
Figure 6 – Tape Leader & Trailer Dimensions
ꢉmꢐoꢈꢈeꢄ Carrier
Carrier ꢀape
Puncꢍeꢄ Carrier
ꢎ mm ꢏ ꢁ2 mm only
ꢃounꢄ ꢅprocꢆet ꢇoleꢈ
STAꢁT
EꢀD
ꢀop Coꢌer ꢀape
ꢉlongateꢄ ꢅprocꢆet ꢇoleꢈ
(ꢊ2 mm tape anꢄ ꢋiꢄer)
ꢁ00 mm
minimum ꢑeaꢄer
ꢒ00 mm minimum
ꢀrailer
Componentꢈ
ꢁꢂ0 mm minimum
ꢀop Coꢌer ꢀape
Figure 7 – Maximum Camber
ꢋlongateꢂ ꢃprocꢄet ꢅoleꢆ
(ꢍ2 mm ꢎ ꢏiꢂer tapeꢆ)
Carrier ꢀape
ꢁounꢂ ꢃprocꢄet ꢅoleꢆ
ꢇ mm maꢈimumꢉ eitꢊer ꢂirection
ꢃtraigꢊt ꢋꢂge
2ꢌ0 mm
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
T2078_A720 • 3/17/2020 14
Aluminum Organic Capacitor (AO-CAP)
A720 Polymer Aluminum
KEMET Electronics Corporation Sales Offices
Forꢀaꢀcompleteꢀlistꢀofꢀourꢀglobalꢀsalesꢀo ꢀꢀces,ꢀpleaseꢀvisitꢀwww.kemet.com/sales.
Disclaimer
Allꢀproductꢀspeci ꢀcations,ꢀstatements,ꢀinformationꢀandꢀdataꢀ(collectively,ꢀtheꢀ“Information”)ꢀinꢀthisꢀdatasheetꢀareꢀsubjectꢀtoꢀchange.ꢀTheꢀcustomerꢀisꢀresponsibleꢀforꢀ
checkingꢀandꢀverifyingꢀtheꢀextentꢀtoꢀwhichꢀtheꢀInformationꢀcontainedꢀinꢀthisꢀpublicationꢀisꢀapplicableꢀtoꢀanꢀorderꢀatꢀtheꢀtimeꢀtheꢀorderꢀisꢀplaced.ꢀAllꢀInformationꢀgivenꢀ
hereinꢀisꢀbelievedꢀtoꢀbeꢀaccurateꢀandꢀreliable,ꢀbutꢀitꢀisꢀpresentedꢀwithoutꢀguarantee,ꢀwarranty,ꢀorꢀresponsibilityꢀofꢀanyꢀkind,ꢀexpressedꢀorꢀimplied.
StatementsꢀofꢀsuitabilityꢀforꢀcertainꢀapplicationsꢀareꢀbasedꢀonꢀKEMETꢀElectronicsꢀCorporation’sꢀ(“KEMET”)ꢀknowledgeꢀofꢀtypicalꢀoperatingꢀconditionsꢀforꢀsuchꢀ
applications,ꢀbutꢀareꢀnotꢀintendedꢀtoꢀconstituteꢀ–ꢀandꢀKEMETꢀspeci ꢀcallyꢀdisclaimsꢀ–ꢀanyꢀwarrantyꢀconcerningꢀsuitabilityꢀforꢀaꢀspeci ꢀcꢀcustomerꢀapplicationꢀorꢀuse.ꢀ
TheꢀInformationꢀisꢀintendedꢀforꢀuseꢀonlyꢀbyꢀcustomersꢀwhoꢀhaveꢀtheꢀrequisiteꢀexperienceꢀandꢀcapabilityꢀtoꢀdetermineꢀtheꢀcorrectꢀproductsꢀforꢀtheirꢀapplication.ꢀAnyꢀ
technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes
no obligation or liability for the advice given or results obtained.
Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component
failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards
(suchꢀasꢀinstallationꢀofꢀprotectiveꢀcircuitryꢀorꢀredundancies)ꢀinꢀorderꢀtoꢀensureꢀthatꢀtheꢀfailureꢀofꢀanꢀelectricalꢀcomponentꢀdoesꢀnotꢀresultꢀinꢀaꢀriskꢀofꢀpersonalꢀinjury
or property damage.
Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other
measures may not be required.
KEMET is a registered trademark of KEMET Electronics Corporation.
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
T2078_A720 • 3/17/2020 15
相关型号：
A720V567M002APE0037280
A720, Polymer Aluminum, 560 uF, 20%, 2 VDC, -55/+105°C, Height Max = 2.1mm
KEMET
A720V567M002APE4R57280
A720, Polymer Aluminum, 560 uF, 20%, 2 VDC, -55/+105°C, Height Max = 2.1mm
KEMET
A720V567M2R5APE0067280
A720, Polymer Aluminum, 560 uF, 20%, 2.5 VDC, -55/+105°C, Height Max = 2.1mm
KEMET
A720V567M2R5APE4R5
A720, Polymer Aluminum, 560 uF, 20%, 2.5 VDC, -55/+105°C, Height Max = 2.1mm
KEMET
©2020 ICPDF网 联系我们和版权申明