13030-01KASLT [KEMET]
Tantalum Capacitor, Tantalum (solid Polymer);
| 型号： | 13030-01KASLT |
| 厂家： | 
KEMET CORPORATION |
| 描述： | Tantalum Capacitor, Tantalum (solid Polymer) 电容器 |
| 文件： | 总11页 (文件大小：1931K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105°C
and DLA Series
Overview
The KEMET T550 Series Polymer Hermetic Seal (PHS)
is a tantalum capacitor with a Ta anode and Ta2O5
tantalum capacitors operated at 50% of rated voltage.
T550 Series PHS also offers higher ripple current handling
capability and a lower ESR range than wet tantalums.
With reduced ESR and enhanced capacitance retention at
higher frequencies and low temperatures, the T550 Series
PHS provides the highest total capacitance and the most
economical solution for high power applications, all within an
approximately 25% lighter package than the equivalent wet
tantalum capacitor.
dielectric. A conductive organic polymer replaces the
traditionally used MnO2 or wet electrolyte as the cathode
plate of the capacitor. This results in very low ESR and
improved capacitance retention at high frequency and low
temperature. The T550 Series PHS also exhibits a benign
failure mode which eliminates the case breach that can
occur in wet tantalum types. Additionally, this part may
be operated at voltages up to 80% of rated voltage with
equivalent or better reliability than traditional MnO2 or wet
Benefits
• Includes F-Tech anode which eliminates hidden defects
in the dielectric
• 100% Simulated Breakdown Screening
• Maximum operating temperature of +105°C
• Meets all requirements of DLA Drawing 13030
• Polymer cathode technology
• Extremely low ESR
• High frequency capacitance retention
• Low temperature capacitance retention
• 100% accelerated steady state aging (240 hours)
• 100% surge current tested, 10 cycles +25°C
•ꢀ Volumetricallyꢀefficient
Click image above for interactive 3D content
Open PDF in Adobe Reader for full functionality
• Non-ignition failure mode
• Approximately 25% lighter than equivalent wet tantalum
• Case dimensions equivalent to
MIL–PRF–39006/22/25/30/31
Applications
Typicalꢀapplicationsꢀincludeꢀhighꢀvoltageꢀpowerꢀmanagementꢀsuchꢀasꢀbuck/boostꢀconverters,ꢀfiltering,ꢀhold-upꢀcapacitors,ꢀ
and other high ripple current applications.
One world. One KEMET
1
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
T2059_T550 • 1/12/2018
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
Ordering Information
T
550
Series
550 =
B
107
M
025
A
T
4251
Capacitor
Class
Case Capacitance Capacitance Rated Voltage Product
Size Code (pF)
Termination
Finish
Surge
Option
Packaging
Tolerance
(VDC)
Level
Blank = Sleeved
0100 = Unsleeved
7200 = Tape &
Reel
7293 & 7443 =
Ammo
T =
B
First two
digits
K = ±10%
M = ±20%
006 = 6.3
008 = 8
A = N/A
B* = DLA
13030
Standard
reliability
T* = DLA
T = 100% Tin Blank = 25°C ±5°C, 10
(Sn)-plated
H = Tin/
lead (SnPb)
solder-
coated
Tantalum Polymer
hermetic
cycles, after constant
voltage conditioning
(KEMET standard)
4251ꢀ=ꢀ10ꢀcycles,ꢀ−55°Cꢀ
and +85°C after constant
voltage conditioning
4252 = 10 cycles,
represent
significantꢀ
figures.ꢀ
Third digit
specifiesꢀ
number of
zeros.
015 = 15
025 = 25
040 = 40
050 = 50
060 = 60
075 = 75
100 = 100
seal
13030 High (5% Pb
reliability minimum)
−55°Cꢀandꢀ+85°Cꢀ
before constant voltage
conditioning
* Only available on select parts. Refer to part number table for details.
Ordering Information – DLA Series
13030
-01
K
A
S
L
B
Drawing
Number Number Tolerance
Dash Capacitance
Lead
Length
Product
Level
Surge Current Testing
Insulation
See
Part
Number
Table
K = ±10%
A = +25°C ±5°C, 10 cycles, after constant
S = Sleeved
U = Unsleeved
L = 1.50
inches
(standard)
B = Standard reliability
T = High reliability
M = ±20% voltage conditioning (KEMET standard)
Bꢀ=ꢀ−55°C,ꢀ−5°C,ꢀ+0°Cꢀandꢀ+85°Cꢀ±5°C;ꢀ
after constant voltage conditioning.
Cꢀ=ꢀ−55°C,ꢀ−5°C,ꢀ+0°Cꢀandꢀ+85°Cꢀ±5°C;ꢀ
before constant voltage conditioning.
* Standard terminations for DLA PN's is "H" (SnPb)
Performance Characteristics
Item
Performance Characteristics
Operating Temperature
Rated Capacitance Range
Capacitance Tolerance
Rated Voltage Range
DF (120 Hz at 25°C)
ESR (100 kHz at 25°C)
−55°Cꢀtoꢀ105°C
20ꢀμFꢀtoꢀ820ꢀμFꢀatꢀ120ꢀHz/25°Cꢀ*
K Tolerance (10%), M Tolerance (20%)
6 – 100 V
ReferꢀtoꢀPartꢀNumberꢀElectricalꢀSpecificationꢀTableꢀ
ReferꢀtoꢀPartꢀNumberꢀElectricalꢀSpecificationꢀTableꢀꢀ
ReferꢀtoꢀPartꢀNumberꢀElectricalꢀSpecificationꢀTable
(at rated voltage up to +85°C and 78% of rated voltage applied at 105°C)
Leakage Current
Packaging
According MIL–PRF–39006
KEMET does not recommend storage above 85°C.
* Additional case sizes and capacitance/voltage are under development.
2
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
T2059_T550 • 1/12/2018
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
Qualification
Test Performed
Method Reference
Test Conditions
Reliability and Environmental Tests
ACꢀRippleꢀLifeꢀatꢀ85˚C
85˚CꢀLife
MIL–PRF–39006
MIL–PRF–39006
KEMET Standard
MIL–PRF–39006
85˚C,ꢀ40ꢀkHzꢀrippleꢀcurrent,ꢀ2,000ꢀhours
85˚C,ꢀratedꢀvoltage,ꢀ2,000ꢀhours
105˚CꢀLife
105°C, 0.78 x rated voltage, 2,000 hours
85˚C,ꢀ1.15ꢀxꢀratedꢀvoltage,ꢀ1,000ꢀcycles,ꢀexceptꢀdeltaꢀcapꢀshallꢀbeꢀ
+10%/−20%
Surge Voltage
Surge Current
Low Temperature Storage
Reverse Voltage
MIL–PRF–39003
MIL–PRF–39006
KEMET Catalog
+25 °C, 10 cycles (Option A), Option B available
−62˚Cꢀforꢀ72ꢀhoursꢀfollowedꢀbyꢀ1ꢀhourꢀatꢀ125˚C
1 V for 8 hours maximum at 25°C, 1 V for 2 hours maximum at 70°C
Physical, Mechanical and Process Tests
Visual and Mechanical
Examination (Internal and
External)
MIL–PRF–39006
Case dimensions, marking
Terminal Strength
Resistance to Solvents
Resistance to Soldering Heat
Solderability
MIL–PRF–39006
MIL–PRF–39006
MIL–PRF–39006
MIL–PRF–39006
Pull test and wire lead bend test
Immersion in (3) solvents
Immersed to within 0.05 inch of capacitor body
Depthꢀofꢀinsertionꢀinꢀfluxꢀandꢀsolderꢀtoꢀwithinꢀ0.062ꢀinchꢀofꢀweldedꢀjoint
MIL–STD–202,
Methods 213, 204
Shock Method 213, Condition I, 100 g peak, Vibration Method 204,
Condition D, 20 g peak
Shock and Vibration
Barometric Pressure
(Reduced)
MIL–PRF–39006
150,000 feet for 5 minutes, voltage applied for 1 minute
Salt Atmosphere (Corrosion)
Moisture Resistance
MIL–PRF–39006
MIL–PRF–39006
MIL–PRF–39006
Subjectedꢀtoꢀfineꢀmistꢀofꢀsaltꢀsolution
65˚Cꢀatꢀ6ꢀvolts
Dielectric Withstanding
Voltage
2,000 VDC, 60 seconds, sleeving examined for evidence of breakdown
Insulation Resistance
MIL–PRF–39003
500ꢀVDC,ꢀ1ꢀminute,ꢀinsulationꢀresistanceꢀnotꢀlessꢀthanꢀ1,000ꢀMΩ
Electrical Characterization
Temperature Stability
Frequency Scan
Reference MIL–PRF–39006
KEMET Standard
−55˚Cꢀtoꢀ105˚C
Impedance, ESR and capacitance versus frequency
3
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
T2059_T550 • 1/12/2018
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
Qualification – DLA Approval Inspection
DLA Requirement
Paragraph
Inspection
Test Name
SS/Lot
Shockꢀ(SpecifiedꢀPulse)1
Vibration, High Frequency1
Thermal Shock
3.3.4
3.3.5
3.3.6
3.3.7
3.3.8
3.3.9
3.3.10
3.3.11
3.3.12
Group I
6 per case size
Salt Atmosphere
Solderability
Terminal Strength
Surge Voltage2
Moisture Resistance
Dielectric Withstanding Voltage
Insulation Resistance
Low Temperature (Storage)
Group II
Group III
12
13
3.3.13
3.3.14
3.3.15
Stability at Low and High
Temperatures
Reverse Voltage
3.3.23
3.3.16
3.3.18
3.3.17
3.3.20
3.3.21
3.3.22
12 per condition
102
Group IV
Group V
Lifeꢀatꢀ85˚C
AC Ripple Life at 85°C
Life at 105°C
8 per case size
Group VI
Group VII
40
6
Barometric Pressure
Resistance to Solvents
Resistance to Soldering Heat
1 No failures for mechanical shock or vibration tests shall be permitted.
2 Surge voltage change in capacitance limits are wider than those in some subsequent tests.
It may be necessary to perform initial measurements again, prior to the individual tests of Group II.
Product Level:
Inspection of product for delivery shall consist of:
B level
T level
GroupꢀAꢀinspectionꢀspecifiedꢀinꢀDrawingꢀ13030
GroupꢀAꢀandꢀgroupꢀBꢀinspectionsꢀspecifiedꢀinꢀDrawingꢀ13030
4
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
T2059_T550 • 1/12/2018
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
Electrical Characteristics
ESR vs. Frequency
10.0
+125°C
+50°C
0°C
+85°C
+25°C
−25°C
−80°C
−55°C
1.0
0.1
0.0
10
100
1,000
10,000
100,000
1,000,000
10,000,000
Frequency (Hz)
Capacitance vs. Frequency
120
100
80
60
40
20
0
+125°C
+50°C
0°C
+85°C
+25°C
−25°C
−80°C
−55°C
10
100
1,000
10,000
100,000
1,000,000
Frequency (Hz)
5
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
T2059_T550 • 1/12/2018
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
Dimensions – Inches (Millimeters)
SIDE VIEW
END VIEW
0.094 (2.39) Maximum
1.50±0.250
(38.10±6.35)
J
D
+
M
L
Insulated Case
Case Code
Case Size
MIL–PRF–39006
T2
Uninsulated Case
D
D
J
max
L
L
M
+0.016 (0.41)
−0.015ꢀ(0.38)
+0.016 (0.41)
−0.015ꢀ(0.38)
± 0.031 (0.79)
±0.031 (0.79)
±0.002 (0.05)
0.822 (20.88)
0.289 (7.34)
0.686 (17.42)
B
0.650 (16.51)
0.279 (7.09)
0.025 (0.64)
Table 1 – Ratings & Part Number Reference
Rated
V o l t a g e Capacitance
Rated
Case
Size
KEMET Part
Number
DLA
Drawing Number
DC
Leakage
Maximum
Ripple
Current
DF
ESR
µA at 25°C
Maximum/5 Minutes 120 Hz Max
% at 25°C
mΩ at 25°C
100 kHz
mArms at
85°C/40 kHz
(V) 85°C
µF
KEMET/EIA (See below for part options) (See below for part options)
6
6
8
140
820
220
680
100
180
560
70
120
390
50
100
40
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
T550B147(1)006A(3)
T550B827(1)006A(3)
T550B227(1)008A(3)
T550B687(1)008A(3)
T550B107(1)010A(3)
T550B187(1)010A(3)
T550B567(1)010A(3)
T550B706(1)015A(3)
T550B127(1)015A(3)
T550B397(1)015A(3)
T550B506(1)025A(3)
T550B107(1)025(2)(3)
T550B406(1)030A(3)
T550B686(1)030A(3)
T550B337(1)035A(3)
T550B107(1)040(2)(3)
T550B127(1)040(2)(3)
T550B256(1)050A(3)
T550B476(1)050A(3)
T550B107(1)050(2)(3)
T550B127(1)050(2)(3)
T550B206(1)060A(3)
T550B396(1)060A(3)
T550B107(1)060(2)(3)
T550B756(1)075(2)(3)
T550B256(1)100(2)(3)
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
6.3
36.9
13.2
40.8
7.5
13.5
42.0
7.9
13.5
43.9
9.4
18.8
9.0
15.3
86.6
30.0
36.0
9.4
17.6
37.5
45.0
9.0
17.6
45.0
42.2
18.8
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
10.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
120
90
120
90
140
110
90
140
110
90
170
190
170
140
180
150
120
170
150
130
90
200
160
100
110
190
1510
1750
1510
1750
1400
1580
1750
1400
1580
1750
1275
1200
1275
1400
1240
1350
1510
1275
1350
1450
1750
1175
1310
1660
1580
1200
8
10
10
10
15
15
15
25
25
30
30
35
40
40
50
50
50
50
60
60
60
75
100
N/A
N/A
N/A
13030-01(1)(4)(5)L(6)
N/A
N/A
N/A
68
330
100
120
25
13030-02(1)(4)(5)L(6)
13030-03(1)(4)(5)L(6)
N/A
47
N/A
100
120
20
39
100
75
13030-04(1)(4)(5)L(6)
13030-05(1)(4)(5)L(6)
N/A
N/A
13030-06(1)(4)(5)L(6)
13030-07(1)(4)(5)L(6)
13030-08(1)(4)(5)L(6)
25
(1) To complete KEMET part number, insert M for ±20% or K for ±10%. Designates capacitance tolerance.
(2) To complete KEMET part number, insert A = N/A, B= standard reliability, or T = high reliability.
(3) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated, H = Standard Solder coated (SnPb 5% Pb minimum). Designates termination
finish.
(4) To complete the DLA PIN number, insert the surge current testing option, A = 25°C after voltage aging, B = −55°C +0°C and +85°C after voltage aging
or C = −55°C +0°C and +85°C before voltage aging
(5) To complete the DLA PIN number, insert the insulation option. S = Sleeved, U = Unseleeved.
(6) To complete the DLA PIN number, insert the product level option. B = standard reliability or T = high reliability.
Refer to Ordering Information for additional detail.
Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitution will
be marked with the higher voltage rating. The 85°C 40 kHz ripple limit is based on the maximum allowed power at 85°C and the maximum expected ESR
at 40 kHz. For this calculation, the 100 kHz ESR limit is multiplied by a factor of 1.3 to account for the frequency dependence of ESR.
6
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
T2059_T550 • 1/12/2018
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
Recommended Voltage Derating Guidelines
120%
100%
80%
60%
40%
20%
0%
−55°Cꢀtoꢀ85°C
85°C to 105°C
78% of VR
% Change in Working DC
Voltage with Temperature
% Change in Working DC Voltage
with Temperature
VR
80%
78%
63%
Recommended Maximum
Application Voltage
(As % of Rated Voltage)
Recommended Maximum Application
Voltage (As % of Rated Voltage)
80% of VR
63% of VR
−55
25
45
85
105
Temperature (°C)
Ripple Current/Ripple Voltage
Permissible AC ripple voltage and current are related to equivalent series resistance (ESR) and the power dissipation
capabilities of the device. Permissible AC ripple voltage that may be applied is limited by two criteria:
1. The positive peak AC voltage plus the DC bias voltage, if any, must not exceed the DC voltage rating of the capacitor.
ꢀ 2.ꢀTheꢀnegativeꢀpeakꢀACꢀvoltageꢀinꢀcombinationꢀwithꢀbiasꢀvoltage,ꢀifꢀany,ꢀmustꢀnotꢀexceedꢀtheꢀallowableꢀlimitsꢀspecifiedꢀ
for reverse voltage.
The maximum power dissipation by case size can be determined using the below left table. The maximum power dissipation
rating stated in the table must be reduced with increasing environmental operating temperatures. Refer to the below right
table for temperature compensation requirements.
Using the Pmax of the device, the maximum allowable rms
ripple current or voltage may be determined.
Maximum Power
Dissipation (Pmax
mWatts at 25°C
with +60°C Rise
)
Case Code
I(max) = √Pmax/R
E(max) = Z √Pmax/R
MIL–PRF–39006/22/
KEMET
B
25/30/31 Case Size
I = rms ripple current (amperes)
E = rms ripple voltage (volts)
T2
715
P
max = maximum power dissipation (watts)
R = ESR at specified frequency (ohms)
Z = Impedance at specified frequency (ohms)
Temperature Compensation Multipliers for
Maximum Power Dissipation (Pmax
)
Tꢀ≤ꢀ45°C
45°Cꢀ<ꢀTꢀ≤ꢀ85°C
85°Cꢀ<ꢀTꢀ≤ꢀ105°C
The maximum power dissipation rating must be reduced with increasing
environmental operating temperatures. Refer to the Temperature
Compensation Multiplier table for details.
1.00
0.70
0.10
T= Environmental Temperature
7
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
T2059_T550 • 1/12/2018
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
Reverse Voltage
Solid tantalum polymer capacitors are polar devices and may be permanently damaged or destroyed if connected with
the wrong polarity. A small reverse voltage is permissible for time periods per the below table. KEMET can offer lower
capacitance in this voltage with higher reverse voltage capability. In addition, we continue to improve our capability for this
characteristic.
Temperature
Permissible Reverse Voltage
25°C
70°C
1 V for 8 hours Maximum
1 V for 2 hours Maximum
Optimum Solder Wave Profile
Solder Wave Peak
Temperature 260ºC
Entrance to Solder Wave
Exit from Solder Wave
(Time in Wave – 2 to 4 Seconds)
Flux Zone
Preheat Zone
Hot Air Debridging
250
225
200
175
150
125
100
75
Exit from
Solder
Machine
80ºC
Entrance to
In-Line Cleaner
Exit from
to 120ºC
Free
Air
Cool
In-Line Cleaner
(time in cleaner
may be less)
Bottom Side
Temperature
Range
Entrance
to Solder
Machine
Immersion in
Cleaning
Vapor
150ºC
Maximum
Top Side
Nominal
50
25
0
1
2
3
4
5
6
Time (Minutes)
Mounting
All encased capacitors will pass the Resistance to Soldering Heat Test of MIL–STD–202, Method 210, Condition C. This test
simulates wave solder of topside board mount product. This demonstration of resistance to solder heat is in accordance
withꢀwhatꢀisꢀbelievedꢀtoꢀbeꢀtheꢀindustryꢀstandard.ꢀMoreꢀsevereꢀtreatmentꢀmustꢀbeꢀconsideredꢀreflectiveꢀofꢀanꢀimproperꢀ
solderingꢀprocess.ꢀTheꢀaboveꢀfigureꢀisꢀaꢀrecommendedꢀsolderꢀwaveꢀprofileꢀforꢀbothꢀaxialꢀandꢀradialꢀleadedꢀsolidꢀtantalumꢀ
capacitors.
8
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
T2059_T550 • 1/12/2018
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
Construction
Detailed Cross Section
Wire Lead (+)
Solder
(100% Sn / SnPb)
Wire Lead (−)
(100% Sn / SnPb)
Anode Tube
Hermetic Seal System
(Glass Seal and Ring)
Brass Can
Insulation
Sleeve
Tantalum Pellet
(See Detail for Layers)
Solder
Hermetic Seal System
(Ring)
Brass Can
Tantalum Wire
Hermetic Seal System
(Glass Seal)
Silver Paint
(Fourth Layer)
Wire Lead (+)
(100% Sn / SnPb)
Carbon
(Third Layer)
Polymer
(Second Layer)
Ta2O5 Dielectric
(First Layer)
Tantalum Wire
Tantalum
Wire Lead (−)
(100% Sn / SnPb)
Anode Tube
Solder
Capacitor Marking
B Case
Series
Rated Capacitance
KT550
100µF
+
KEMET ID
Polarity Marks
10% 60V +
1202AAAA
Capacitance
Tolerance,
Rated Voltage
(VDC)
4 Digit Date Code, Lot Code
Date Code
3 Digit
4 Digit
5 = 2015
6 = 2016
7 = 2017
8 = 2018
9 = 2019
15 = 2015
16 = 2016
17 = 2017
18 = 2018
19 = 2019
Year
01 = 1st week of the year to
52 = 52nd week of the year
Week
9
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
T2059_T550 • 1/12/2018
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
Storage
Tantalum hermetically sealed capacitors should be stored in normal working environments. While the capacitors themselves
are quite robust in other environments, solderability will be degraded by exposure to high temperatures, high humidity,
corrosive atmospheres, and long term storage. In addition, packaging materials will be degraded by high temperature
– reels may soften or warp and tape peel force may increase. KEMET recommends that maximum storage temperature
notꢀexceedꢀ40°Cꢀandꢀmaximumꢀstorageꢀhumidityꢀnotꢀexceedꢀ60%ꢀrelativeꢀhumidity.ꢀTemperatureꢀfluctuationsꢀshouldꢀbeꢀ
minimized to avoid condensation on the parts and atmospheres should be free of chlorine and sulphur bearing compounds.
For optimized solderability capacitors stock should be used promptly, preferably within three years of receipt.
Packaging
Case Size
Pieces per Tray
KEMET
EIA
B
T2
20
Weight
Case Size
Average Weight
(grams)
KEMET
EIA
B
T2
3.63
10
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
T2059_T550 • 1/12/2018
Tantalum Through-Hole Capacitors – Hermetically Sealed
T550 Axial Polymer Hermetic Seal (PHS) 105ºC and DLA Series
KEMET Electronics Corporation Sales Offices
Forꢀaꢀcompleteꢀlistꢀofꢀourꢀglobalꢀsalesꢀoffiꢀꢀces,ꢀpleaseꢀvisitꢀwww.kemet.com/sales.
Disclaimer
Allꢀproductꢀspecifiꢀcations,ꢀstatements,ꢀinformationꢀandꢀdataꢀ(collectively,ꢀtheꢀ“Information”)ꢀinꢀthisꢀdatasheetꢀareꢀsubjectꢀtoꢀchange.ꢀTheꢀcustomerꢀisꢀresponsibleꢀforꢀ
checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.
All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
StatementsꢀofꢀsuitabilityꢀforꢀcertainꢀapplicationsꢀareꢀbasedꢀonꢀKEMETꢀElectronicsꢀCorporation’sꢀ(“KEMET”)ꢀknowledgeꢀofꢀtypicalꢀoperatingꢀconditionsꢀforꢀsuchꢀ
applications,ꢀbutꢀareꢀnotꢀintendedꢀtoꢀconstituteꢀ–ꢀandꢀKEMETꢀspecifiꢀcallyꢀdisclaimsꢀ–ꢀanyꢀwarrantyꢀconcerningꢀsuitabilityꢀforꢀaꢀspecifiꢀcꢀcustomerꢀapplicationꢀorꢀuse.ꢀ
The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any
technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no
obligation or liability for the advice given or results obtained.
Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component
failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards
(suchꢀasꢀinstallationꢀofꢀprotectiveꢀcircuitryꢀorꢀredundancies)ꢀinꢀorderꢀtoꢀensureꢀthatꢀtheꢀfailureꢀofꢀanꢀelectricalꢀcomponentꢀdoesꢀnotꢀresultꢀinꢀaꢀriskꢀofꢀpersonalꢀinjuryꢀorꢀ
property damage.
Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other
measures may not be required.
KEMET is a registered trademark of KEMET Electronics Corporation.
11
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
T2059_T550 • 1/12/2018
相关型号：
©2020 ICPDF网 联系我们和版权申明