SLEB19N4SF_技术文档

Cannon SLE

Snap-Lock Environmentally Sealed - Rectangular

Engineering Quick Reference Selection Guide

Part No. Description

Contact Arrangement

Plug, Straight PCB

No. of Contacts

19 Position

28 Position

19 Position

28 Position

For PCB Layout, see page 24.

SLEB19P4S SLEB19P4D

SLEB19P4L SLEB19P4SG

SLEB19P4R SLEB19P4UG

SLEB19P4U SLEB19P4DG

SLEB19S2SF SLEB19S2R

SLEB19S2S SLEB19S2U

SLEB19S2L SLEB19S2D

19

SLEB19N3P SLEB19N3PN

SLEB19N3PM SLEB19N3

130415-0000 130415-0004

130415-0001 130415-0005

130415-0002

SLEB19T3P SLEB19T3

SLEB19T3PM SLEB19T3H

SLEB19T3PN

SLEC28P4S SLEC28P4D

SLEC28P4L SLEC28P4SG

SLEC28P4R SLEC28P4UG

SLEC28P4U SLEC28P4DG

SLEC28S2SF SLEC28S2R

SLEC28S2S SLEC28S2U

SLEC28S2L SLEC28S2D

28

SLEC28N3P SLEC28N3PN

SLEC28N3PM SLEC28N3

SLEC28T3P SLEC28T3PE

SLEC28T3PM SLEC28T3

SLEC28T3PN

130415-0000 130415-0004

130415-0001 130415-0005

130415-0002

SLEB130411 SLEB19S12

SLEB130411 SLEB19S14

19

28

SLEC130415 SLEC28S12

SLEC130414 SLEC28S14

How to Order

SLE

B

19

P

4

S

G

**

Series Prefix

Size

Number of Contacts

Contact Termination

Connector Type

Connector Termination

Mechanical Modifier

Material/Finish Modifier

Dimensions shown in mm

Specifications and dimensions subject to change

www.ittcannon.com

20

Cannon SLE

Snap-Lock Environmentally Sealed - Rectangular

Engineering Quick Reference Selection Guide

Plug, 90° PCB

28 Position

Plug, In-line

Receptacle, In-line

19 Position

28 Position

19 Position

28 Position

For PCB Layout, see page 25

130408-0000 130408-0004

130408-0001 130408-0010

130408-0002 130408-0011

130408-0003 130408-0012

130413-0000 130413-0003

130413-0001 130413-0004

130413-0002 130413-0005

130414-0000 130414-0002

130414-0001 130414-0004

130412-0000 130412-0004

130412-0001 130412-0010

130412-0002 130412-0011

130412-0003 130412-0012

130413-0000 130413-0003

130413-0001 130413-0004

130413-0002 130413-0005

130414-0000 130414-0002

130414-0001 130414-0004

Note: For configuration contact Cannon.

Series Prefix

SLE - SLE-Snap Lock Environmental

Contact Termination

T - Tuning Fork Straight [Plug with 3,05 (.120)

min. PCB tails]

N - Tuning Fork 90° [Plug with 2,54 (.100) min.

PCB tails]

Connector Termination

S - Straight (Endbell)

L - 90° Left (Endbell)

R - 90° Right (Endbell)

U - 90° Up (Endbell)

D - 90° Down (Endbell)

P - Potted (PCB Only)

Size

B-19 Cavity Housing

C-28 Cavity Housing

P - Crimp Pin (Receptacle)

S - Crimp Socket (Plug)

Number of Contacts

19 or 28

P1 - Crimp Pin Power (Receptacle)

S1 - Crimp Socket Power (Pin)

Mechanical Modifier

F - With Flange Mount (Plug only)

G - Screwlock Applications (Receptacle only)

M - Metric Threaded Inserts

Connector Type

2 - Plug, In-line (Cable-to-Cable)

3 - Plug, PCB

N - Threaded Inserts #6-32

4 - Receptacle, In-line (Cable-to-Cable)

E - Threaded Inserts #6-32

Dimensions shown in mm

Specifications and dimensions subject to change

www.ittcannon.com

21

Cannon SLE

Snap-Lock Environmentally Sealed - Rectangular

The Snap Lock Environmental Series is environmentally-sealed

connector created for printed circuit board, blackbox, cable-to-cable,

or bulkhead applications.

When your under-the-hood requirements call for tough performance,

the SLE "snaps" into a tightly sealed connection that can withstand

heat, shock and vibration. The connector is designed to preserve the

integrity of the solid state package, while protecting against

contaminants - even when unmated.

Polarization, scoop-proofing and hand insertion of contacts are part

of the package. Gold, tin/lead-plated stamped contacts add

durability. A rugged, thermoplastic receptacle body maximizes

performance by withstanding temperature variances from -40°C to

+125°C.

The SLE series is available in both 19 and 28 contact cavity

configurations. It can also be adapted to robotic assembly. Should

your requirement demand higher density configurations, consult

Customer Service.

Product Feature and Benefits

·

Superior environmental sealing

-40°C to +125°C continuous operation at rated

current

Available in two sizes, 19 and 28 contacts

Crimp stamped gold, tin/lead plated contacts

Hand insertable/removable contacts

Current rating 5 A and 13 A versions

·

Low millivolt drop

·

Latch with tactile and audible feedback

Low installed cost

Meets both signal and power requirements

Versatile cable strain relief, up, down, straight, left

ad right, flange/bulkhead

Small footprint on P.C. board and low profile

5-way alternate polarization

Integral mold latch. Adaptable to robotic

assembly.

Multi-direction, easily assembled endbells

Optional secondary bail latch

·

Connector mating assurance

Performance Specifications

Contact Resistance 10 mΩ maximum

Insulation Resistance 100 MΩ minimum

Current Rating 5 A signal continuous at 125°C all contacts

13 A power continuous at 125°C all contacts

Dielectric Withstanding Voltage 1000 Vrms AC at sea level

Applicable Cannon Specification CS-189

Operating Temperature -40°C to +125°C

Crimp Contacts Semi-automatic or hand crimpable

Wire Size 20-16 AWG

Wire Insulations Sealing Range 2,41 (.095) to 3,30 (.130) dia.

Polarization 'D' shaped interface with five alternate positions.

Contact Insertion No tool required. Suitable for automation.

Contact Extraction Rear removable

Contact Retention 25 lbs. Minimum per contact

Wire Strip Length 5,59 (.220) to 5,33 (.210)

Materials and Finishes

Connector Housing High temperature thermoplastic

Contacts Copper alloy

Finish Engaging area: Gold over nickel

Crimp/P.C. tail area: Tin/lead over nickel

Environmental Seal High temperature silicone elastomer

Dimensions shown in mm

Specifications and dimensions subject to change

www.ittcannon.com

22

Cannon SLE

Snap-Lock Environmentally Sealed - Rectangular

Contact Cavity Arrangement

Face View - Engaging Face of Plug

Size B

Size C

19 Contacts

28 Contacts

Power Version*

*Contact Cannon

Polarization

Normal

W

X

Y

Z

Dimensions shown in mm

Specifications and dimensions subject to change

www.ittcannon.com

23

Cannon SLE

Snap-Lock Environmentally Sealed - Rectangular

Endbells

Connectors are supplied with endbell assemblies.

Part number by Shell Size

B Max.

F Max.

Cable Entry I.D.

SLEB

SLEC

26,16 (1.030)

50,80 (2.000)

66,04 (2.600)

14,73 (.580)

19,81 (.780)

Plug, In-line (Cable-to-Cable)

With Flange Endbell

(Plug Only)

Note: Plugs are supplied with endbell assemblies.

Shell

Size

Number of

Contacts

D

Part Number*

Nomenclature

A Max.

C Max.

0,ꢀ8 (.01ꢁ)

SLEB

SLEC

19

28

130409-0000*

130409-0001*

130409-0002*

130409-0003*

130409-0004*

130409-0005*

130413-0000

130413-0001

130413-0002

130413-0003

130413-0004

130413-0005

SLEB19S2SF

SLEB19S2S

SLEB19S2L

SLEB19S2R

SLEB19S2U

SLEB19S2D

SLEC28S2SF

SLEC28S2S

SLEC28S2L

SLEC28S2R

SLEC28S2U

SLEC28S2D

71,88 (2.830)

87,11 (3.430)

47,50 (1.870)

62,74 (2.470)

59,05 (2.325)

74,29 (2.925)

*Select polarization, see page 25.

Dimensions shown in mm

Specifications and dimensions subject to change

www.ittcannon.com

24

Cannon SLE

Snap-Lock Environmentally Sealed - Rectangular

Receptacle, In-line (Cable-to-Cable)

90° Left and Right

Straight

Screwlock

Note: Receptacles are supplied with endbell assemblies.

Shell

Size

Number of

E

Contacts

Part Number*

Nomenclature

A Max.

C Max. D Max.

44,07 (1.735)

0,ꢀ8 (.01ꢁ)

F Max.

SLEB

SLEC

19

28

130408-0000*

130408-0001*

130408-0002*

130408-0003*

130408-0004*

130408-0010*

130408-0011*

130408-0012*

130412-0000

130412-0001

130412-0002

130412-0003

130412-0004

130412-0010

130412-0011

130412-0012

SLEB19P4S

SLEB19P4L

SLEB19P4R

SLEB19P4U

SLEB19P4D

SLEB19P4SG

SLEB19P4UG

SLEB19P4DG

SLEC28P4S

SLEC28P4L

SLEC28P4R

SLEC28P4U

SLEC28P4D

SLEC28P4SG

SLEC28P4UG

SLEC28P4DG

59,44 (2.340)

76,45 (3.010)

50,58 (2.000)

66,04 (2.600)

55,87 (2.200)

71,11 (2.800)

64,25 (2.530)

79,49 (3.130)

44,07 (1.735)

59,31 (2.335)

*Select polarization, see page 23.

Dimensions shown in mm

Specifications and dimensions subject to change

www.ittcannon.com

25

Cannon SLE

Snap-Lock Environmentally Sealed - Rectangular

Plug, PCB, Straight

4,80-4,69

2X

(.189-.185)

A

B

24,13-23,72

(.950-.930)

C

L

18,42-18,03

(.725-.710)

D

Panel Cutout

Shell

Size

Number of

Contacts

Part Number*

Nomenclature

A Max.

B Max.

D Max.

E Max.

SLEB

SLEC

19

28

130411-0000*

130411-0001*

130411-0002*

130411-0004*

130411-0005*

130415-0000

130415-0001

130415-0002

130415-0004

130415-0005

SLEB19T3P

SLEB19T3PM

SLEB19T3PN

SLEB19T3E

SLEB19T3

SLEC28T3P

SLEC28T3PM

SLEC28T3PN

SLEC28T3PE

SLEC28T3

63,50 (2.500)

78,94 (3.108)

74,94 (3.100)

54,61 (2.150)

56,13 (2.210)

71,37 (2.810)

47,62 (1.875)

62,86 (2.475)

*Select polarization, see page 23.

Recommended PCB Layout, Straight

SLE B19 (19 contacts)

SLE C28 (28 contacts)

Dimensions shown in mm

Specifications and dimensions subject to change

www.ittcannon.com

26

Cannon SLE

Snap-Lock Environmentally Sealed - Rectangular

Plug, PCB, 90˚

Panel Cutout

Shell

Size

Number of

Contacts

Part Number*

Nomenclature

A Max.

B Max.

C Max.

D Max.

E Max.

SLEB

SLEC

19

28

130410-0000*

130410-0001*

130410-0002*

130410-0004*

130414-0000

130414-0001

130414-0002

130414-0004

SLEB19N3P

SLEB19N3PM

SLEB19N3PN

SLEB19N3

SLEC28N3P

SLEC28N3PM

SLEC28N3PN

SLEC28N3

63,50 (2.500)

78,94 (3.108)

74,94 (3.100)

54,61 (2.150)

35,81 (1.410)

51,05 (2.010)

56,13 (2.210)

71,37 (2.810)

47,62 (1.875)

62,86 (2.475)

*Select polarization, see page 23.

Recommended PCB Layout, 90˚

SLE B19 (19 contacts)

SLE C28

(28 contacts)

Dimensions shown in mm

Specifications and dimensions subject to change

www.ittcannon.com

27

Cannon SLE

Snap-Lock Environmentally Sealed - Rectangular

Contacts, Stamped, ꢁ and 1ꢀ Amp

Socket (use in plugs)

Hooded Socket

Pin (use in receptacles)

Hooded Socket

Reeled

Description

5 A

13 A

Socket Part Number Reeled

110238-1016 (030-2480-007)

Pin Part Number

110238-0446 (030-2464-007)

110238-2004 (030-2464-003)

Socket Part Number

110238-04888 (030-2480-000)

110238-2003 (030-2480-003)

Number of Contacts

4,500

4,000

Accessories

Sealing Plug

Female Screw Lock

Latch Clip Retainer

Material: Thermoplastic, Color: Natural

Part Number: 225-0093-000

Order 2 per connector

Material: Steel

Finish: Zinc

Part Number: 265-0061-000

Bail Latch For Redundant Latch Applications

SLEB

SLEC

029-0281-000

029-0281-001

Test Methods

Insulation Resistance

Dielectric Withstanding Voltage

Contact Resistance

Low Level Contact Resistance

Crimp Tensile Strength

Contact Retention

Mating Separating Force

Durability

MIL-STD-1344

MIL-STD-202

MIL-STD-1344

MIL-STD-202

SAE

Method 3003.1

Method 3001.1

Method 3004.1

Method 3002.1

Method 2003.1

Method 2007.1

Method 2013.1

Method 2016

Method 108 Condition D

Method 213 Condition I

Method 2002.1

Method 2005.1 Condition VI 20 Hours/Axis

Method 110

Temperature Life

Mechanical Shock

Maintenance Aging

Vibration

Sand and Dust

Salt and Spray

Method 101 Condition A

Method 106

Proposed

Humidity

Steam Cleaning/Pressure Wash

Dimensions shown in mm

Specifications and dimensions subject to change

www.ittcannon.com

28

Cannon SLE

Snap-Lock Environmentally Sealed - Rectangular

Extraction Tool

Contact Extraction Tool

Part Number: 274-7068-001

Tip Part Number: ꢀ2ꢀ-9ꢁ19-000

· A Standard CET - SLE/SLC is available for

extraction of the individual crimp contacts. Insertion

tool is not required.

Insertion/Extraction Instructions for Crimp Contacts

Insertion Tool

No insertion tool is required. The

contact is easily snapped in

from the rear of the connector

manually.

1. Move to the rear of the

connector so that the contact

cavities can be identified.

2. Insert a crimp terminated

assembly into a selected cavity.

3. Continue the forward movement

until and audible snap can be felt

and heard. Slight pull in the

opposite direction will confirm

complete insertion.

Extraction

1. Open the CET - SLE Extraction

tool and place it over the insulation

of the wire.

2. Using a straight motion forward,

insert the tool along the wire until it

bottoms against the connector. (Do

not use a screwing motion -

damage will result.)

3. While the extraction tool is in

place, simply pull the wire/contact

assembly out.

4. Remove the extraction tool.

Extraction is complete.

Dimensions shown in mm

Specifications and dimensions subject to change

www.ittcannon.com

29

Cannon SLE

Snap-Lock Environmentally Sealed - Rectangular

Hand Crimp Tool Operation

Hand Crimp Tool - CCT - SLC / SLE

Part Number: 99ꢁ-0002-2ꢀ2

The CCT-SLC/SLE hand crimp tool is designed to crimp individual SLC/SLE contacts on wire sizes 16, 18, and 20 AWG.

Each cycle is ratchet-controlled (The tool must be completely closed before it can be reopened) to assure a satisfactory

crimp each time. Over and under crimps are eliminated.

This tool is for use when the requirement is for low to moderate volume quantities, and for on-site applications where semi-

automatic tools cannot be practically used.

1. Cycle the CCT - SLE / SLC hand tool to the open

position.

2. While pressing upward on the locator spring, insert

the contact with tails upward completely into the

locator.

3. When correctly positioned the contact should be

located beyond flush with the edge of the CCT - SLE

/ SLC and positioned in the concave polished split

level crimp.

4. Partially (usually the first click) Cycle the hand tool

assuring that the upward thrusting tails of the contact

has started engaging with the top jaw of the tool.

(There is a slight tendency for the contact to roll out

of vertical alignment.)

5. Insert the pre-stripped wire into the crimp area of

the contact and completely cycle the tool.

6. While pressing upward on the locator spring

withdraw the crimp termination.

Wire Stripping

5 and 13 A Contact

7. The result will be a perfect termination.

8. Note that there are no unterminated wire strands,

and that some strand ends can be seen at the

forward edge of the crimp. Also note the insulation is

gripped by the smaller secondary crimp. Distortion is

at a minimum, both axially and laterally - no sharp

edges.

Tolerance

Low

High

A

B

2,41 (.095)

3,30 (.130)

5,33 (.210)

5,59 (.220)

Dimensions shown in mm

Specifications and dimensions subject to change

www.ittcannon.com

30

Cannon SLE

Snap-Lock Environmentally Sealed - Rectangular

Lease Automatic Tooling - North America*

ABT-607 Pneumatic Crimper

The ABT-607 is a pneumatic powered and controlled

Machine Crimp Rate:

machine. It is designed for customers with moderate

volume. This machine is designed to semi-

automatically crimp stamped and formed contacts

onto pre-stripped stranded or single conductor

electrical wire. This machine will accommodate size

34 thru 12 AWG wire and is actuated by the use of a

foot pedal.

800 per hour

Power Requirements:

Pneumatic = 100 psi, 2 cu. ft. per min.

ABT-ꢁ00 UCCD

The ABT-500 Universal Cannon Crimp Die, is a

flywheel driven, electronically controlled machine that

is designed to semi-automatically crimp stamped and

Machine Crimp Rate:

1300 per hour

formed contacts on stranded or single conductor, pre- Power Requirements:

stripped wire. This machine will accommodate size

34 thru 12 WG wire. The machine is actuated by the

use of a foot pedal.

Electrical = 115VAC, 60Hz, 20A

ABT-620 UCCS

The ABT-620 Universal Cannon Crimper/Stripper is a

pneumatic powered, microprocessor controlled

machine. It is designed to semi-automatically strip

insulation from stranded or single conductor electrical

wire and attach a stamped and formed contact by

crimping. The machine will accommodate 34 thru 12

AWG wire. Primary application of the machine is the

termination of jacketed cable where the individual

leads cannot be stripped by fully automated

Machine Crimp Rate:

1200+ per hour

Power Requirements:

Electrical = 115VAC, 60Hz, 20A

Pneumatic = 80 psi, 3 cu. ft. per min.

equipment. The ABT-620 UCCS operates

automatically upon insertion of a wire or it can be

switched over to foot pedal operation if desired.

* For other geographical regions, contact Cannon for details.

Dimensions shown in mm

Specifications and dimensions subject to change

www.ittcannon.com

31

Cannon SLE

Snap-Lock Environmentally Sealed - Rectangular

Crimp Pot Cross Section

D

CRIMP

WIDTH

C

CRIMP

HEIGHT

Crimp Height and Width

Wire Gauge (AWG)

18

CRIMP POT

CROSS SECTION

16

20

C*

.064*

.066*

D Ref.

.082

C*

.056*

.062*

D Ref.

.080

C*

.054*

.058*

D Ref.

.080

Signal (5A)

Power (13A)

* Hand Tools are .002 and machines are .001

The wire crimp heights listed are only

reference and valid for the

correspondingly listed wire size, wire

plating and wire stranding.

The wire crimp tensile values must be

used to assure the performance of

crimped contacts.

Insulation Height and Width

Wire Gauge (AWG)

18

16

20

For wire crimp information not listed in

this table, please contact Cannon.

Height

Max

Width

Max**

.115**

Height

Max

.105

Width

Max**

.110**

Height

Max

.105

Width

Max**

.110**

Signal (5A)

.110

Power (13A)

.110

.105

** Measurements are taken without crimping wire insulation.

Crimp Tensile Strength

Wire Trim Dimension

(.220 - .210)

(.130 - .095)

Wire Size (AWG)

Tensile Min (lbs)

16

35 lbs.

18

25 lbs.

20

20lbs.

Dimensions shown in mm

Specifications and dimensions subject to change

www.ittcannon.com

32

Snap-Lock Environmentally Sealed - Rectangular

Cannon SLE

Test Parameters

SLC Products are designed to meet Cannon specifications CS-206, CS-210, and CS-216. Items of most general interest to users are designers are listed below.

Test

Description

Reference

Paragraph

Requirements

Environmental

Sealing

3.2.3.5

3.2.3.6

3.2.3.7

3.2.3.8

3.2.3.9

3.2.3.10

Sand and Dust MIL-STD-202 Method 110 Test Condition A

5% salt spray 96 hours

10 cycles of 24 hours, 90-98% humidity

Steam Cleaning/Pressure Wash 95°C, 375 Cycles 750 PSIG

Solvent Resistance/Immersion (see 3.2.3.9)

Thermal Shock 100 Cycles -40°C to +125°C 3°C

Contact Crimp

Tensile Strength

3.2.2.1

The minimum tensile load required to separate the wire from the contact, either by pulling the wire out of the crimp joint or by

breaking the wire within the crimp joint shall not be less than the applicable limits as specified. Wire breakage or contact damage

not due to crimping at less than tensile loads shall not constitute a failure.

Wire Size AWG

Crimp Tensile Strength, Pounds Minimum

16

18

20

35

25

20

Insulation

Resistance

Mated and wired connectors shall exhibit an insulation resistance greater than 100 megohms between all contacts. This limit

shall apply after exposure to each environment including salt solution immersion. Tests shall be performed at 100 VDC 10%.

3.2.1.1

3.2.1.2

3.2.1.4

3.2.3.3

Dielectric

Withstanding

Voltage

Low Level

Contact

Resistance

Mechanical

Shock

Wired and mated connectors shall show no evidence of breakdown between adjacent contacts when tested at 1000 VDC 5%.

Connectors shall meet this requirement after exposure to each environment. Current leakage shall be less than 1.0 milliamp.

The low level contact resistance of mated contacts shall be less than 10 milliohms when measured across the contacts and

crimp joints. The test current shall be a maximum of 100 milliamps with an open circuit test voltage of 20 millivolts maximum.

Connectors shall be subjected to three shocks in each direction applied along the three mutually perpendicular axes of the

connector test specimen for a total of 12 shocks. Each shock shall consist of a terminal peak sawtooth pulse with a peak value

of 100 g's and a duration of 6 milliseconds.

Vibration

Connectors shall be subjected to random vibration in accordance with MIL-STD-1344, Method 2005.1, test condition VI for 20

hours along each of the following three axes:

3.2.3.4

Direction

Grms

22.8

12.2

10.2

Transverse axis of connector (Y)

Longitudinal axis of connector (Z)

Mating axis

Electrical continuity of the connectors shall be monitored during the last 20 minutes sweep in each axis with a test current of 100

milliamps or less and a test voltage less than 2VDC. Electrical discontinuities in excess of 10 microseconds shall be cause of

failure.

Durability

Contact

3.2.2.5

Connectors shall be subjected to 25 cycles of mating and unmating at room temperature. Following this test there shall be no

evidence of damage to the contacts, contact plating, connector housing or seals which may prove detrimental to reliable

performance of the connector.

3.2.2.2

3.2.2.3

3.2.2.4

3.2.2.9

Contacts shall not be displaced greater than 0.030 inches from the connector body when a force of 10 pounds is applied. When

this test follows maintenance again the same contacts shall be tested.

Maintenance

Aging

Shall consist of subjecting each wired receptacle to 4 cycles of removal and reinsertion of 20% of the contacts or a minimum of 6

per connector with approved tooling.

Mating and

Separating

Force

Solvent

Resistance

Immersion

The maximum force required to mate the plug and receptacle shall be 25 pounds. The maximum force required to separate the

plug and receptacle shall be 15 pounds. The rate of travel shall be one inch per minute.

Connectors shall be subjected to the following fluids at the temperature and length of time specified. Following the fluid

dip or immersion, the connectors shall be immersed to a depth of 2 to 12 inches in a ꢁ% salt-water solution for 24

hours at room temperature. At the completion of the salt-water immersion test, while still immersed, the connectors

shall meet the insulation resistance requirement specified herein.

Fluid

Method

Temperature

No. 2 Diesel Fluid

Methyl Alcohol

Antifreeze

Immersion (2)

Dip (1)

140°F

Room Temperature

- Prestone

Immersion (2)

180°F

- 50% Water/50%

Ethylene Glycol

Degreaser

- Gunk

Dip (1)

Immersion (2)

Room Temperature

200°F

- Mineral Spirits

Paint (Oil Base)

Lubricating Oil

(SAE 10 W40)

Brake Fluid

Dip (1)

Room Temperature

(Delco Supreme)

Transmission Fluid

Dip (1)

fully submerged and pressurized

@ 7 psi. (Dextron)

(1) Dip: Connectors shall withstand a one second dip and a three minute air dry for a total of 80 cycles.

(2) Immersion: Connectors shall withstand immersion for one hour.

Temperature

Life

3.2.3.1

3.2.3.2

Connectors shall be subjected to a temperature of 125°C 3°C for a period of 1000 hours. At the end of the temperature soak

period and after removal from the chamber, the connectors shall meet the insulation resistance and dielectric withstanding

voltage requirements specified herein. Connectors shall be operated at rated current throughout the duration of the temperature

life test. Upon removal from the chamber at the conclusion of the test, the connectors shall show no visual signs of damage,

which may be detrimental to the performance of the connector.

Thermal Cycling

Connectors shall be subjected to 100 thermal cycles from -40°C to +125°C. One cycle shall consist of the transitions from room

temperature to -40°C to +125°C, and from 125°C to room temperature. One cycle shall be accomplished in a three-hour period

with a minimum stabilization period of 15 minutes at each temperature extreme. The chamber temperature transition rate shall

be a minimum of 1.30°C per minute and a maximum of 6.00°C per minute.

Specifications and dimensions subject to change

www.ittcannon.com

33


型号：	SLEB19N4SF
厂家：	ITT Cannon
描述：	Snap-Lock Environmentally Sealed - Rectangular 弹簧锁密封环境 - 矩形
文件：	总14页 (文件大小：381K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

SLEB19N4SF [ITT]

相关型号：

UL1042

ZXFV201

ZXFV201N14

ZXFV201N14TA

ZXFV201N14TC

ZXFV202E5

ZXFV202N8

ZXFV203N14

ZXFV301N16(1)

ZXFV302N16

ZXFV4089

ZXFV4089N8