X9429WV14 [INTERSIL]
Single Digitally Controlled Potentiometer; 单数字控制电位器
| 型号： | X9429WV14 |
| 厂家： | 
Intersil |
| 描述： | Single Digitally Controlled Potentiometer |
| 文件： | 总21页 (文件大小：366K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
X9429
®
Low Noise/Low Power/2-Wire Bus
Data Sheet
October 19, 2005
FN8248.2
DESCRIPTION
The X9429 integrates a single digitally controlled
Single Digitally Controlled Potentiometer
(XDCP™)
potentiometer (XDCP) on
integrated circuit.
a
monolithic CMOS
FEATURES
• Single Voltage Potentiometer
• 64 Resistor Taps
The digital controlled potentiometer is implemented
using 63 resistive elements in a series array. Between
each element are tap points connected to the wiper
terminal through switches. The position of the wiper on
the array is controlled by the user through the 2-wire
bus interface. The potentiometer has associated with it
a volatile Wiper Counter Register (WCR) and a four
non-volatile Data Registers that can be directly written
to and read by the user. The contents of the WCR
controls the position of the wiper on the resistor array
though the switches. Powerup recalls the contents of
the default data register (DR0) to the WCR.
• 2-wire Serial Interface for Write, Read, and
Transfer Operations of the Potentiometer
• Wiper Resistance, 150Ω Typical at 5V
• Non-Volatile Storage of Multiple Wiper Positions
• Power-on Recall. Loads Saved Wiper Position
on Power-up.
• Standby Current < 5µA Max
• V : 2.7V to 5.5V Operation
CC
• 2.5kΩ, 10kΩ Total Pot Resistance
• Endurance: 100, 000 Data Changes per Bit per
Register
• 100 yr. Data Retention
The XDCP can be used as a three-terminal
• 14 Ld TSSOP, 16 Ld SOIC
• Low Power CMOS
• Pb-Free Plus Anneal Available (RoHS Compliant)
potentiometer or as a two terminal variable resistor in
a wide variety of applications including control,
parameter adjustments, and signal processing.
BLOCK DIAGRAM
VCC
VH/RH
write
read
transfer
inc / dec
address
data
status
10kΩ
64-taps
POT
Power-on Recall
wiper
Bus
Interface &
Control
Wiper Counter
Register (WCR)
2-wire
bus
interface
Data Registers
4 Bytes
control
VW/RW
VSS
VL/RL
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
XDCP is a trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2005. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
1
X9429
Ordering Information
POTENTIOMETER
PART NUMBER
X9429WS16*
PART MARKING
VCC LIMITS (V) ORGANIZATION (kΩ) TEMP RANGE (°C)
PACKAGE
X9429WS
5 ±10%
10
2.5
10
0 to 70
0 to 70
16 Ld SOIC (300 mil)
X9429WS16Z* (Note)
X9429WS16I*
X9429WS Z
X9429WS I
X9429WS Z I
X9429WV
16 Ld SOIC (300 mil) (Pb-free)
16 Ld SOIC (300 mil)
-40 to 85
-40 to 85
0 to 70
X9429WS16IZ* (Note)
X9429WV14*
16 Ld SOIC (300 mil) (Pb-free)
14 Ld TSSOP (4.4mm)
X9429WV14Z* (Note)
X9429WV14IZ* (Note)
X9429WV14I*
X9429WV Z
X9429WV Z I
X9429WV I
X9429YS
0 to 70
14 Ld TSSOP (4.4mm) (Pb-free)
14 Ld TSSOP (4.4mm) (Pb-free)
14 Ld TSSOP (4.4mm)
-40 to 85
-40 to 85
0 to 70
X9429YS16*
16 Ld SOIC (300 mil)
X9429YS16Z* (Note)
X9429YS16I*
X9429YS Z
X9429YS I
X9429YS Z I
X9429YV
0 to 70
16 Ld SOIC (300 mil) (Pb-free)
16 Ld SOIC (300 mil)
-40 to 85
-40 to 85
0 to 70
X9429YS16IZ* (Note)
X9429YV14*
16 Ld SOIC (300 mil) (Pb-free)
14 Ld TSSOP (4.4mm)
X9429YV14Z* (Note)
X9429YV14I*
X9429YV Z
X9429YV I
X9429YV Z I
X9429WS F
0 to 70
14 Ld TSSOP (4.4mm) (Pb-free)
14 Ld TSSOP (4.4mm)
-40 to 85
-40 to 85
0 to 70
X9429YV14IZ* (Note)
X9429WS16-2.7*
14 Ld TSSOP (4.4mm) (Pb-free)
16 Ld SOIC (300 mil)
2.7 to 5.5
X9429WS16Z-2.7* (Note) X9429WS Z F
X9429WS16I-2.7* X9429WS G
X9429WS16IZ-2.7* (Note) X9429WS Z G
X9429WV14-2.7* X9429WV F
X9429WV14Z-2.7* (Note) X9429WV Z F
X9429WV14I-2.7* X9429WV G
X9429WV14IZ-2.7* (Note) X9429WV Z G
X9429YS16-2.7* X9429YS F
X9429YS16Z-2.7* (Note) X9429YS Z F
X9429YS16I-2.7* X9429YS G
X9429YS16IZ-2.7* (Note) X9429YS Z G
X9429YV14-2.7* X9429YV F
X9429YV14Z-2.7* (Note) X9429YV Z F
X9429YV14I-2.7* X9429YV G
0 to 70
16 Ld SOIC (300 mil) (Pb-free)
16 Ld SOIC (300 mil)
-40 to 85
-40 to 85
0 to 70
16 Ld SOIC (300 mil) (Pb-free)
14 Ld TSSOP (4.4mm)
0 to 70
14 Ld TSSOP (4.4mm) (Pb-free)
14 Ld TSSOP (4.4mm)
-40 to 85
-40 to 85
0 to 70
14 Ld TSSOP (4.4mm) (Pb-free)
16 Ld SOIC (300 mil)
2.5
0 to 70
16 Ld SOIC (300 mil) (Pb-free)
16 Ld SOIC (300 mil)
-40 to 85
-40 to 85
0 to 70
16 Ld SOIC (300 mil) (Pb-free)
14 Ld TSSOP (4.4mm)
0 to 70
14 Ld TSSOP (4.4mm) (Pb-free)
14 Ld TSSOP (4.4mm)
-40 to 85
-40 to 85
X9429YV14IZ-2.7* (Note) X9429YV Z G
*Add "T1" suffix for tape and reel.
14 Ld TSSOP (4.4mm) (Pb-free)
NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
FN8248.2
2
October 19, 2005
X9429
DETAILED FUNCTIONAL DIAGRAM
VCC
Power-on Recall
WIPER
10kΩ
64--taps
DR1
DR0
RH/VH
COUNTER
REGISTER
(WCR)
Control
DATA
DR2 DR3
SCL
R /VL
L
INTERFACE
AND
CONTROL
SDA
A3
R /VW
W
CIRCUITRY
A2
A0
WP
VSS
CIRCUIT LEVEL APPLICATIONS
SYSTEM LEVEL APPLICATIONS
• Vary the gain of a voltage amplifier
• Adjust the contrast in LCD displays
• Provide programmable dc reference voltages for
comparators and detectors
• Control the power level of LED transmitters in
communication systems
• Control the volume in audio circuits
• Trim out the offset voltage error in a voltage
amplifier circuit
• Set the output voltage of a voltage regulator
• Trim the resistance in Wheatstone bridge circuits
• Control the gain, characteristic frequency and
Q-factor in filter circuits
• Set the scale factor and zero point in sensor signal
conditioning circuits
• Vary the frequency and duty cycle of timer ICs
• Vary the dc biasing of a pin diode attenuator in RF
circuits
• Set and regulate the DC biasing point in an RF
power amplifier in wireless systems
• Control the gain in audio and home entertainment
systems
• Provide the variable DC bias for tuners in RF
wireless systems
• Set the operating points in temperature control
systems
• Control the operating point for sensors in industrial
systems
• Trim offset and gain errors in artificial intelligent
systems
• Provide a control variable (I, V, or R) in feedback
circuits
FN8248.2
October 19, 2005
3
X9429
PIN CONFIGURATION
SOIC
TSSOP
VCC
NC
NC
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
14
1
2
3
4
5
6
7
VCC
NC
NC
NC
NC
NC
A2
RL/VL
13
12
11
10
RL/VL
RH/VH
RH/VH
RW/VW
A3
X9429
X9429
A2
RW/VW
A3
SCL
SCL
SDA
SDA
VSS
A0
9
8
A0
NC
WP
VSS
WP
PIN ASSIGNMENTS
TSSOP pin
SOIC pin
Symbol
NC
Brief Description
1
2
1
2
No Connect
No Connect
No Connect
NC
3
3
NC
4
4
A2
Device Address for 2-wire bus.
Serial Clock for 2-wire bus.
Serial Data Input/Output for 2-wire bus.
System Ground
5
5
SCL
SDA
VSS
WP
A0
6
6
7
8
8
9
Hardware Write Protect
9
10
11
12
13
14
16
15
7
Device Address for 2-wire bus.
Device Address for 2-wire bus.
Wiper Terminal of the Potentiometer.
High Terminal of the Potentiometer.
Low Terminal of the Potentiometer.
System Supply Voltage
10
11
12
13
14
A3
R
W / VW
RH / VH
RL / VL
VCC
NC
No Connect
NC
No Connect
PIN DESCRIPTIONS
Hos t Interface Pins
Serial Clock (SCL)
Device Address (A , A , A )
0 2 3
The Address inputs are used to set the least
significant 3 bits of the 8-bit slave address. A match in
the slave address serial data stream must be made
with the Address input in order to initiate
communication with the X9429. A maximum of 8
devices may occupy the 2-wire serial bus.
The SCL input is used to clock data into and out of the
X9429.
Serial Data (SDA)
Potentiometer Pins
SDA is a bidirectional pin used to transfer data into
and out of the device. It is an open drain output and
may be wire-ORed with any number of open drain or
open collector outputs. An open drain output requires
the use of a pull-up resistor. For selecting typical
values, refer to the guidelines for calculating typical
values on the bus pull-up resistors graph.
R /V , R /V
L
H
H
L
The R /V and R /V inputs are equivalent to the
H
H
L
L
terminal connections on either end of a mechanical
potentiometer.
FN8248.2
4
October 19, 2005
X9429
R /V
during this period the receiver pulls the SDA line LOW
to acknowledge that it successfully received the eight
bits of data.
W
W
The wiper outputs are equivalent to the wiper output of
a mechanical potentiometer.
The X9429 will respond with an acknowledge after
recognition of a start condition and its slave address
and once again after successful receipt of the
command byte. If the command is followed by a data
byte the X9429 will respond with a final acknowledge.
Hardware Write Protect Input WP
The WP pin when low prevents nonvolatile writes to the
Data Registers.
PRINCIPLES OF OPERATION
Array Description
The X9429 is
a
highly integrated microcircuit
The X9429 is comprised of a resistor array. The array
contains 63 discrete resistive segments that are
connected in series. The physical ends of the array
are equivalent to the fixed terminals of a mechanical
incorporating a resistor array and its associated
registers and counters and the serial interface logic
providing direct communication between the host and
the XDCP potentiometers.
potentiometer (V /R and V /R inputs).
H
H
L
L
At both ends of the array and between each resistor
segment is a CMOS switch connected to the wiper
Serial Interface
The X9429 supports a bidirectional bus oriented
protocol. The protocol defines any device that sends
data onto the bus as a transmitter and the receiving
device as the receiver. The device controlling the
transfer is a master and the device being controlled is
the slave. The master will always initiate data transfers
and provide the clock for both transmit and receive
operations. Therefore, the X9429 will be considered a
slave device in all applications.
(V /R ) output. Within each individual array only one
W
W
switch may be turned on at a time. These switches are
controlled by the Wiper Counter Register (WCR). The
six bits of the WCR are decoded to select, and enable,
one of sixty-four switches.
The WCR may be written directly, or it can be changed
by transferring the contents of one of four associated
Data Registers into the WCR. These Data Registers
and the WCR can be read and written by the host
system.
Clock and Data Conventions
Data states on the SDA line can change only during
Device Addressing
SCL LOW periods (t
). SDA state changes during
LOW
SCL HIGH are reserved for indicating start and stop
conditions.
Following a start condition the master must output the
address of the slave it is accessing. The most
significant four bits of the slave address are the device
type identifier (refer to Figure 1). For the X9429 this is
fixed as 0101[B].
Start Condition
All commands to the X9429 are preceded by the start
condition, which is a HIGH to LOW transition of SDA
Figure 1. Slave Address
while SCL is HIGH (t
). The X9429 continuously
HIGH
monitors the SDA and SCL lines for the start condition
and will not respond to any command until this
condition is met.
Device Type
Identifier
0
1
0
1
A3
A2
0
A0
Stop Condition
All communications must be terminated by a stop
condition, which is a LOW to HIGH transition of SDA
while SCL is HIGH.
Device Address
The next four bits of the slave address are the device
address. The physical device address is defined by the
Acknowledge
Acknowledge is a software convention used to provide
a positive handshake between the master and slave
devices on the bus to indicate the successful receipt of
data. The transmitting device, either the master or the
slave, will release the SDA bus after transmitting eight
bits. The master generates a ninth clock cycle and
state of the A , A , and A inputs. The X9429 compares
0
2
3
the serial data stream with the address input state; a
successful compare of all three address bits is required
for the X9429 to respond with an acknowledge. The A ,
0
A , and A inputs can be actively driven by CMOS input
2
3
signals or tied to V or V
.
CC
SS
FN8248.2
5
October 19, 2005
X9429
Acknowledge Polling
Flow 1. ACK Polling Sequence
The disabling of the inputs, during the internal
nonvolatile write operation, can be used to take
advantage of the typical 5ms EEPROM write cycle
time. Once the stop condition is issued to indicate the
end of the nonvolatile write command the X9429
initiates the internal write cycle. ACK polling can be
initiated immediately. This involves issuing the start
condition followed by the device slave address. If the
X9429 is still busy with the write operation no ACK will
be returned. If the X9429 has completed the write
operation an ACK will be returned, and the master can
then proceed with the next operation.
Nonvolatile Write
Command Completed
Enter ACK Polling
Issue
START
Issue Slave
Address
Issue STOP
Instruction Structure
ACK
NO
Returned?
The next byte sent to the X9429 contains the instruction
and register pointer information. The four most
significant bits are the instruction. The next four bits
point to one of four associated registers. The format is
shown below in Figure 2.
YES
NO
Further
Operation?
Figure 2. Instruction Byte Format
YES
Register
Select
Issue
Instruction
Issue STOP
Proceed
I3
I2
I1
I0
R1 R0
0
0
Proceed
Instructions
The four high order bits define the instruction. The
next two bits (R1 and R0) select one of the four
registers that is to be acted upon when a register
oriented instruction is issued. Bits 0 and 1 are defined
to be 0.
Four of the seven instructions end with the
transmission of the instruction byte. The basic
sequence is illustrated in Figure 3. These two-byte
instructions exchange data between the Wiper
Counter Register and one of the Data Registers. A
transfer from a Data Register to a Wiper Counter
Register is essentially a write to a static RAM. The
response of the wiper to this action will be delayed
t
. A transfer from the Wiper Counter Register
WRL
(current wiper position), to a Data Register is a write to
nonvolatile memory and takes a minimum of t
complete.
to
WR
Four instructions require a three-byte sequence to
complete. These instructions transfer data between the
host and the X9429; either between the host and one of
the Data Registers or directly between the host and the
Wiper Counter Register. These instructions are:
FN8248.2
6
October 19, 2005
X9429
Figure 3. Two-Byte Instruction Sequence
SCL
SDA
S
T
A
R
T
0
1
0
1
A3 A2
0
A0
A
C
K
I3 I2
I1 I0 R1 R0
0
0
A
C
K
S
T
O
P
Read Wiper Counter Register (read the current wiper
position of the selected pot), write Wiper Counter
Register (change current wiper position of the selected
pot), read Data Register (read the contents of the
selected nonvolatile register) and write Data Register
(write a new value to the selected Data Register). The
sequence of operations is shown in Figure 4.
the master can clock the selected wiper up and/or
down in one segment steps; thereby, providing a fine
tuning capability to the host. For each SCL clock pulse
(t
) while SDA is HIGH, the selected wiper will
HIGH
move one resistor segment towards the V /R
H
H
terminal. Similarly, for each SCL clock pulse while
SDA is LOW, the selected wiper will move one resistor
segment towards the V /R terminal. A detailed
illustration of the sequence and timing for this
operation are shown in Figures 5 and 6 respectively.
L
L
The Increment/Decrement command is different from
the other commands. Once the command is issued
and the X9429 has responded with an acknowledge,
Table 1. Instruction Set
Instruction Set
Instruction
I
I
I
I
R
R
X
X
0
Operation
3
2
1
0
1
0
1
Read Wiper Counter
Register
1
1
1
1
1
0
0
0
1
1
0
1
1
0
0
1
0
1
0
1
0
0
0
0
0
0
Read the contents of the Wiper Counter Register
Write Wiper Counter
Register
0
0
0
0
0
0
0
0
Write new value to the Wiper Counter Register
Read the contents of the Data Register pointed to
by R1 - R0
Read Data Register
Write Data Register
1/0 1/0
1/0 1/0
1/0 1/0
Write new value to the Data Register pointed to by
R1 - R0
XFR Data Register to
Wiper Counter Register
Transfer the contents of the Data Register pointed
to by R1 - R0 to its Wiper Counter Register
XFR Wiper Counter
Register to Data Regis-
ter
Transfer the contents of the Wiper Counter Register
to the Data Register pointed to by R1 - R0
1
0
1
0
1
1
0
0
1/0 1/0
0
0
0
0
Increment/Decrement
Wiper Counter Register
Enable Increment/decrement of the Wiper Counter
Register
0
0
Note: (1) 1/0 = data is one or zero
FN8248.2
October 19, 2005
7
X9429
Figure 4. Three-Byte Instruction Sequence
SCL
SDA
S
T
A
R
T
0
1
0
1
A3 A2
0
A0
A
C
K
I3 I2
I1 I0 R1 R0
0
0
A
C
K
0
0
D5 D4 D3 D2 D1 D0
A
C
K
S
T
O
P
Figure 5. Increment/Decrement Instruction Sequence
SCL
SDA
S
T
A
R
T
0
1
0
1
A3 A2
0
A0
A
C
K
I3 I2
I1 I0 R1 R0
0
0
A
C
K
I
I
D
E
C
1
S
T
O
P
I
D
N
C
1
N
C
2
N
C
n
E
C
n
Figure 6. Increment/Decrement Timing Limits
INC/DEC
CMD
Issued
tWRID
SCL
SDA
Voltage Out
VW/RW
FN8248.2
October 19, 2005
8
X9429
Figure 7. Acknowledge Response from Receiver
SCL from
1
Master
8
9
Data Output
from Transmitter
Data Output
from Receiver
START
Acknowledge
Figure 8. Detailed Potentiometer Block Diagram
Serial Data Path
Serial
Bus
Input
VH/RH
From Interface
Circuitry
C
o
u
n
t
Register 0
Register 2
Register 1
8
6
Parallel
Bus
Input
e
r
Wiper
D
e
c
o
d
e
Register 3
Counter
Register
(WCR)
INC/DEC
Logic
If WCR = 00[H] then VW/RW = VL/RL
UP/DN
UP/DN
If WCR = 3F[H] then VW/RW = VH/RH
VL/RL
Modified SCL
CLK
VW/RW
FN8248.2
October 19, 2005
9
X9429
DETAILED OPERATION
Register Descriptions
The potentiometer has a Wiper Counter Register and
four Data Registers. A detailed discussion of the
register organization and array operation follows.
Data Registers, (6-Bit), Nonvolatile
D5
NV
D4
NV
D3
NV
D2
NV
D1
NV
D0
NV
Wiper Counter Register
(MSB)
(LSB)
The X9429 contains a Wiper Counter Register. The
Wiper Counter Register can be envisioned as a 6-bit
parallel and serial load counter with its outputs
decoded to select one of sixty-four switches along its
resistor array. The contents of the WCR can be altered
in four ways: it may be written directly by the host via
the write Wiper Counter Register instruction (serial
load); it may be written indirectly by transferring the
contents of one of four associated Data Registers via
the XFR Data Register instruction (parallel load); it can
Four 6-bit Data Registers for each XDCP.
– {D5~D0}: These bits are for general purpose not
volatile data storage or for storage of up to four
different wiper values. The contents of Data Register
0 are automatically moved to the Wiper Counter
Register on power-up.
Wiper Counter Register, (6-Bit), Volatile
be modified one step at
a
time by the
WP5
V
WP4
V
WP3
V
WP2
V
WP1
V
WP0
V
Increment/Decrement instruction. Finally, it is loaded
with the contents of its Data Register zero (DR0) upon
power-up.
(MSB)
(LSB)
The WCR is a volatile register; that is, its contents are
lost when the X9429 is powered-down. Although the
register is automatically loaded with the value in DR0
upon power-up, it should be noted this may be
different from the value present at power-down.
One 6-bit wiper counter register for each XDCP.
– {D5~D0}: These bits specify the wiper position of the
respective XDCP. The Wiper Counter Register is
loaded on power-up by the value in Data Register 0.
The contents of the WCR can be loaded from any of
the other Data Register or directly. The contents of
the WCR can be saved in a DR.
Data Registers
The potentiometer has four nonvolatile Data
Registers. These can be read or written directly by the
host and data can be transferred between any of the
four Data Registers and the Wiper Counter Register. It
should be noted all operations changing data in one of
these registers is a nonvolatile operation and will take
a maximum of 10ms.
If the application does not require storage of multiple
settings for the potentiometer, these registers can be
used as regular memory locations that could possibly
store system parameters or user preference data.
FN8248.2
10
October 19, 2005
X9429
Instruction Format
Notes: (1) “MACK”/”SACK”: stands for the acknowledge sent by the master/slave.
(2) “A3 ~ A0”: stands for the device addresses sent by the master.
(3) “X”: indicates that it is a “0” for testing purpose but physically it is a “don’t care” condition.
(4) “I”: stands for the increment operation, SDA held high during active SCL phase (high).
(5) “D”: stands for the decrement operation, SDA held low during active SCL phase (high).
Read Wiper Counter Register (WCR)
S
T
A
R
T
device type
identifier
device
addresses
instruction
opcode
wiper position
(sent by slave on SDA)
S
A
C
K
S
A
C
K
M S
A T
C O
K P
W W W W W W
0 0 P P P P P P
A A
A
0
0
1
0
1
0
1
0
0
1
0
0
0
0
3
2
5
4 3 2 1 0
Write Wiper Counter Register (WCR)
S
T
A
R
T
device type
identifier
device
addresses
instruction
opcode
wiper position
(sent by master on SDA)
S
A
C
K
S
A
C
K
S S
A T
C O
K P
W W W W W W
0 0 P P P P P P
A A
A
0
0
1
0
1
0
1
0
1
0
0
0
0
0
3
2
5
4 3 2 1 0
Read Data Register (DR)
S device type device
addresses
instruction
opcode
register
addresses
wiper position/data
(sent by slave on SDA)
S
A
C
K
S
A
C
K
M S
A T
C O
K P
T
A
R
T
identifier
W W W W W W
0 0 P P P P P P
A A
A
0
R R
1 0
0
1
0
1
0
1
0
1
1
0
0
3
2
5
4 3 2 1 0
Write Data Register (DR)
S device type
device
addresses
instruction
opcode
register
addresses
wiper position/data
(sent by master on SDA)
S
S
A
C
K
S S
T
A
R
T
identifier
A
C
K
A T HIGH-VOLTAGE
C O WRITE CYCLE
K P
W W W W W W
0 0 P P P P P P
A A
A
0
R R
1 0
0
1
0
1
0
1
1
0
0
0
0
3
2
5
4 3 2 1 0
XFR Data Register (DR) to Wiper Counter Register (WCR)
S device type
device
addresses
instruction
opcode
register
addresses
S
A
C
K
S S
A T
C O
K P
T
A
R
T
identifier
A A
A
0
R R
1 0
0
1
0
1
0
1
1
0
1
0 0
3
2
FN8248.2
October 19, 2005
11
X9429
XFR Wiper Counter Register (WCR) to Data Register (DR)
S device type
device
addresses
instruction
opcode
register
addresses
S
A
C
K
S S
T
A
R
T
identifier
A T HIGH-VOLTAGE
C O WRITE CYCLE
K P
A A
A
0
R R
1 0
0
1
0
1
0
1
1
1
0
0 0
3
2
Increment/Decrement Wiper Counter Register (WCR)
S
T
A
R
T
device type
identifier
device
addresses
instruction
opcode
increment/decrement
(sent by master on SDA)
S
A
C
K
S
A
C
K
S
T
O
P
A A
A
0
I/ I/
D D
I/ I/
D D
0
1
0
1
0
0
0
1
0
0
0
0
0
.
.
.
.
3
2
SYMBOL TABLE
Guidelines for Calculating Typical Values of Bus
Pull-Up Resistors
WAVEFORM
INPUTS
OUTPUTS
120
VCC MAX
IOL MIN
RMIN
=
=1.8kΩ
Must be
steady
Will be
steady
100
80
tR
RMAX
Max.
=
CBUS
May change
from Low to
High
Will change
from Low to
High
60
40
20
0
Resistance
May change
from High to
Low
Will change
from High to
Low
Min.
Resistance
Don’t Care:
Changes
Allowed
Changing:
State Not
Known
0
20 40 60 80 100 120
Bus Capacitance (pF)
N/A
Center Line
is High
Impedance
FN8248.2
12
October 19, 2005
X9429
ABSOLUTE MAXIMUM RATINGS
COMMENT
Temperature under bias : ........................-65°C to +135°C
Storage temperature: .............................-65°C to +150°C
Voltage on SCL, SDA any address input
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only; functional operation of the
device (at these or any other conditions above those
listed in the operational sections of this specification)
is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
with respect to V :...................................-1V to +7V
SS
∆V = | (V - V ) | .............................................................5V
H
L
Lead temperature (soldering, 10 seconds)..............300°C
(10 seconds)...................................................±6mA
I
W
RECOMMENDED OPERATING CONDITIONS
Temperature
Commercial
Industrial
Min.
0°C
Max.
+70°C
+85°C
Device
X9429
Supply Voltage (V ) Limits
CC
5V ±10%
-40°C
X9429-2.7
2.7V to 5.5V
ANALOG CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.)
Limits
Symbol
Parameter
End to End Resistance Tolerance
Power rating
Min.
Typ.
Max.
±20
50
Unit
%
Test Conditions
mW
mA
Ω
25°C, each pot
IW
Wiper current
±3
RW
Wiper resistance
150
400
250
1000
VCC
Wiper current = ± 1mA, VCC = 5V
Wiper current = ± 1mA, VCC = 3V
VSS = 0V
Ω
VTERM
Voltage on any VH/RH or VL/RL pin
VSS
V
Noise
Resolution (4)
-120
1.6
dBV
%
Ref: 1kHz
Absolute Linearity (1)
Relative Linearity (2)
Temperature Coefficient of RTOTAL
Ratiometric Temperature Coefficient
±1
MI(3)
MI(3)
ppm/°C
Vw(n)(actual) - Vw(n)(expected)
±0.2
Vw(n + 1) - [Vw(n) + MI]
±300
±20 ppm/°C
pF
CH/CL/CW Potentiometer Capacitances
10/10/25
See Circuit #3,
Spice Macromodel
FN8248.2
13
October 19, 2005
X9429
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)
Limits
Symbol
Parameter
Min.
Typ.
Max.
Unit
Test Conditions
ICC1
VCC supply current
(nonvolatile write)
1
mA
fSCL = 400kHz, SDA = Open,
Other Inputs = VSS
ICC2
VCC supply current
(move wiper, write, read)
100
µA
fSCL = 400kHz, SDA = Open,
Other Inputs = VSS
ISB
ILI
VCC current (standby)
Input leakage current
Output leakage current
Input HIGH voltage
Input LOW voltage
5
10
µA
µA
µA
V
SCL = SDA = VCC, Addr. = VSS
VIN = VSS to VCC
ILO
VIH
VIL
VOL
10
VOUT = VSS to VCC
VCC x 0.7
-0.5
VCC x 0.5
VCC x 0.1
0.4
V
Output LOW voltage
V
IOL = 3mA
Notes: (1) Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as
a potentiometer.
(2) Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potenti-
ometer. It is a measure of the error in step size.
(3) MI = RTOT/63 or (RH - RL)/63, single pot
(4) Typical = individual array resolutions.
ENDURANCE AND DATA RETENTION
Parameter
Minimum endurance
Data retention
Min.
100,000
100
Unit
Data changes per bit per register
Years
CAPACITANCE
Symbol
Test
Max.
Unit
pF
Test Conditions
(5)
CI/O
Input/output capacitance (SDA)
8
6
VI/O = 0V
VIN = 0V
(5)
CIN
Input capacitance (A0, A2,and A3 and SCL)
pF
POWER-UP TIMING
Symbol
Parameter
VCC Power-up ramp rate
Min.
Typ.
Max.
Unit
V/msec
(6)
tRVCC
0.2
50
POWER-UP AND POWER-DOWN REQUIREMENTS
There are no restrictions on the power-up or power-down conditions of V
and the voltage applied to the
CC
potentiometer pins provided that V is always more positive than or equal to V , V , and V , i.e., V ≥ V , V , V .
CC
H
L
W
CC
H
L
W
The V ramp rate spec is alway in effect.
CC
Notes: (5) This parameter is periodically sampled and not 100% tested
(6) Sample tested only.
FN8248.2
October 19, 2005
14
X9429
A.C. TEST CONDITIONS
Circuit #3 SPICE Macro Model
Input pulse levels
VCC x 0.1 to VCC x 0.9
10ns
RTOTAL
Input rise and fall times
Input and output timing level
RH
RL
CL
V
CC x 0.5
CH
CW
10pF
EQUIVALENT A.C. LOAD CIRCUIT
10pF
25pF
5V
2.7V
RW
1533Ω
SDA Output
100pF
100pF
AC TIMING (Over recommended operating conditions)
Symbol
fSCL
Parameter
Min.
Max.
Unit
kHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Clock frequency
100
2500
600
1300
600
600
600
100
30
400
tCYC
Clock cycle time
tHIGH
tLOW
Clock high time
Clock low time
tSU:STA
tHD:STA
tSU:STO
tSU:DAT
tHD:DAT
tR
Start setup time
Start hold time
Stop setup time
SDA data input setup time
SDA data input hold time
SCL and SDA rise time
SCL and SDA fall time
300
300
900
tF
tAA
SCL low to SDA data output valid time
SDA data output hold time
tDH
50
50
TI
Noise suppression time constant at SCL and SDA inputs
Bus free time (prior to any transmission)
WP, A0, A2, A3 setup time
tBUF
1300
0
tSU:WPA
tHD:WPA
WP, A0, A2, A3 hold time
0
FN8248.2
15
October 19, 2005
X9429
HIGH-VOLTAGE WRITE CYCLE TIMING
Symbol
Parameter
Typ.
Max.
Unit
tWR
High-voltage write cycle time (store instructions)
5
10
ms
XDCP TIMING
Symbol
Parameter
Min. Max. Unit
tWRPO
tWRL
Wiper response time after the third (last) power supply is stable
Wiper response time after instruction issued (all load instructions)
10
10
10
µs
µs
µs
tWRID
Wiper response time from an active SCL/SCK edge (increment/decrement instruction)
Note: (8) A device must internally provide a hold time of at least 300ns for the SDA signal in order to bridge the undefined region of the falling
edge of SCL.
TIMING DIAGRAMS
START and STOP Timing
(START)
(STOP)
tR
tF
SCL
SDA
tSU:STA
tHD:STA
tSU:STO
tR
tF
Input Timing
tCYC
tHIGH
SCL
SDA
tLOW
tSU:DAT
tHD:DAT
tBUF
Output Timing
SCL
SDA
tDH
tAA
FN8248.2
16
October 19, 2005
X9429
XDCP Timing (for All Load Instructions)
(STOP)
SCL
LSB
SDA
tWRL
VW/RW
XDCP Timing (for Increment/Decrement Instruction)
SCL
Wiper Register Address
Inc/Dec
Inc/Dec
SDA
tWRID
VW/RW
Write Protect and Device Address Pins Timing
(START)
(STOP)
SCL
...
(Any Instruction)
...
SDA
...
tSU:WPA
tHD:WPA
WP
A0, A2
A3
FN8248.2
17
October 19, 2005
X9429
APPLICATIONS INFORMATION
Basic Configurations of Electronic Potentiometers
+VR
VR
VW/RW
I
Three terminal Potentiometer;
Variable voltage divider
Two terminal Variable Resistor;
Variable current
Application Circuits
Noninverting Amplifier
Voltage Regulator
VS
+
–
VO
VIN
VO (REG)
317
R1
R2
Iadj
R1
R2
VO = (1+R2/R1)VS
VO (REG) = 1.25V (1+R2/R1)+Iadj R2
Offset Voltage Adjustment
Comparator with Hysteresis
R1
R2
VS
VS
–
+
VO
–
+
100kΩ
VO
TL072
10kΩ
10kΩ
R1
R2
10kΩ
VUL = {R1/(R1+R2)} VO(max)
LL = {R1/(R1+R2)} VO(min)
+5V
V
FN8248.2
18
October 19, 2005
X9429
Application Circuits (continued)
Attenuator
Filter
C
VS
+
–
R2
VO
R1
R3
–
+
R
VO
VS
R2
R4
All RS = 10kΩ
R1
G
O = 1 + R2/R1
VO = G VS
-1/2 ≤ G ≤ +1/2
fc = 1/(2πRC)
Inverting Amplifier
Equivalent L-R Circuit
R1
R2
VS
R2
C1
–
+
VS
+
VO
–
R1
R3
ZIN
VO = G VS
G = - R2/R1
ZIN = R2 + s R2 (R1 + R3) C1 = R2 + s Leq
(R1 + R3) >> R2
Function Generator
C
R2
R1
–
+
–
+
R
R
}
}
A
B
frequency ∝ R1, R2, C
amplitude ∝ RA, RB
FN8248.2
19
October 19, 2005
X9429
PACKAGING INFORMATION
14-Lead Plastic, TSSOP, Package Type V
.025 (.65) BSC
.169 (4.3)
.177 (4.5)
.252 (6.4) BSC
.193 (4.9)
.200 (5.1)
.047 (1.20)
.0075 (.19)
.0118 (.30)
.002 (.05)
.006 (.15)
.010 (.25)
Gage Plane
0° - 8°
Seating Plane
.019 (.50)
.029 (.75)
Detail A (20X)
.031 (.80)
.041 (1.05)
See Detail “A”
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
FN8248.2
20
October 19, 2005
X9429
PACKAGING INFORMATION
16-Lead Plastic SOIC (300 Mil Body) Package Type S
0.290 (7.37)
0.299 (7.60)
0.393 (10.00)
0.420 (10.65)
PIN 1 INDEX
PIN 1
0.014 (0.35)
0.020 (0.51)
0.403 (10.2 )
0.413 ( 10.5)
(4X) 7°
0.092 (2.35)
0.105 (2.65)
0.003 (0.10)
0.012 (0.30)
0.050 (1.27)
0.010 (0.25)
0.050" Typical
X 45°
0.020 (0.50)
0° - 8 °
0.050"
0.0075 (0.19)
0.010 (0.25)
Typical
0.420"
0.015 (0.40)
0.050 (1.27)
0.030" Typical
16 Places
FOOTPRINT
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN8248.2
21
October 19, 2005
相关型号：
X9429WV14-2.7
10K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO14, 4.40 MM, PLASTIC, TSSOP-14
RENESAS
X9429WV14I
10K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO14, 4.40 MM, PLASTIC, TSSOP-14
RENESAS
X9429WV14I-2.7
10K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO14, 4.40 MM, PLASTIC, TSSOP-14
RENESAS
X9429WV14I-2.7T1
10K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO14, 4.40 MM, PLASTIC, TSSOP-14
RENESAS
X9429WV14I-2.7T2
10K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO14, 4.40 MM, PLASTIC, TSSOP-14
RENESAS
X9429WV14IT1
10K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO14, 4.40 MM, PLASTIC, TSSOP-14
RENESAS
X9429WV14IZ
Single Digitally Controlled Potentiometer (XDCP™); SOIC16, TSSOP14; Temp Range: See Datasheet
RENESAS
©2020 ICPDF网 联系我们和版权申明