ISL4089 [INTERSIL]
DC-Restored Video Amplifier; 直流恢复视频放大器
| 型号： | ISL4089 |
| 厂家： | 
Intersil |
| 描述： | DC-Restored Video Amplifier |
| 文件： | 总9页 (文件大小：345K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
ISL4089
®
Data Sheet
June 28, 2006
FN6192.1
DC-Restored Video Amplifier
Features
The ISL4089 is complete DC-restored monolithic video
amplifier sub-system. It contains a high performance video
amplifier and a nulling, sample-and-hold amplifier designed
to establish a programmable DC output level.
• Complete video level DC-restoration system
• 0.03% differential gain and 0.05° differential phase
accuracy
• 300MHz -3dB small signal bandwidth at A = 1
V
When the HOLD logic input “0” is applied the DC restore
function is active. The sample-and-hold amplifier loop is
closed and used to null the DC offset of the video amplifier.
This can occur during sync, or, at any time that a black level
is expected. When the HOLD input “1” is applied, the
correcting voltage is stored on the video amplifier’s input
coupling capacitor. This condition must be true during active
video. The restored DC voltage level can be adjusted using
• 150MHz -3dB small signal bandwidth at A = 2
V
• 300V/µs Slew Rate
• 0.1dB flatness to 80MHz
• +5V single supply operation
• TTL/CMOS compatible hold signal
• Pb-free plus anneal available (RoHS compliant)
an external reference voltage applied to the V
pin.
REF
The device operates from a single +5V supply and is ideal
for +5V only systems when used with a sync separator, such
as the EL1883.
Applications
• Input amplifier in video equipment
• DC-restoration amplifier in video mixers
The ISL4089 is intended to directly replace the EL4089 only
in certain applications. This direct replacement requires that
the single positive supply is no higher than +5.5V and that no
part of the clamped output goes below ground. The NC on
pin 6 is not internally connected, so it can be connected to
the -5V pin in existing EL4089 applications.
Related Documents
• AN1261: ISL4089EVAL1 User’s Guide
• AN1089: EL4089 and EL4390 DC-Restored Video
Amplifier
The ISL4089 is specified for operation over -40°C to +85°C
temperature range.
Ordering Information
PART
TAPE &
PKG.
PART NUMBER MARKING
REEL PACKAGE DWG. #
Pinout
ISL4089IBZ
(See Note)
4089IBZ
4089IBZ
-
8 Ld SO
(Pb-free)
MDP0027
MDP0027
ISL4089
(8 Ld SOIC)
TOP VIEW
ISL4089IBZ-T7
(See Note)
7”
8 Ld SO
(Pb-free)
NOTE: Intersil Pb-free plus anneal products employ special Pb-free
material sets; molding compounds/die attach materials and 100%
matte tin plate termination finish, which are RoHS compliant and
compatible with both SnPb and Pb-free soldering operations. Intersil
Pb-free products are MSL classified at Pb-free peak reflow
temperatures that meet or exceed the Pb-free requirements of
IPC/JEDEC J STD-020.
V+
IN-
-
+
VOUT
N/C
GND
IN+
VREF
+
HOLD
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2006. All Rights Reserved.
1
All other trademarks mentioned are the property of their respective owners.
ISL4089
Absolute Maximum Ratings (T = 25°C)
A
Voltage between V+ and GND. . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V
Voltage between IN+, IN-, HOLD, V and GND
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Operating Junction Temperature . . . . . . . . . . . . . . .-40°C to +125°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
REF
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND -0.5;V+ +0.5V
Supply Turn-on Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . 1V/µs
Digital and Analog Input Current (Note 1) . . . . . . . . . . . . . . . . 50mA
Output Current (Continuous) . . . . . . . . . . . . . . . . . . . . . . . . . . 60mA
ESD Rating
Human Body Model (Per MIL-STD-883 Method 3015.7). . . .3000V
Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .250V
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: T = T = T
A
J
C
DC Electrical Specifications V+ = +5V, Load = 1kΩ; T = +25°C
A
PARAMETER
DESCRIPTION
CONDITION
MIN
TYP
MAX
UNIT
AMPLIFIER SECTION (HOLD = 5V)
Ib+
Ib-
IN+ Input Bias Current
V
V
= 2.5V
= 1.3V
-7
20
-1
µA
µA
dB
V
IN+
IN-
IN- Input Bias Current
Open Loop Gain
-30
A
60
VOL
V
V
High Output Level
Low Output Level
Short Circuit Current
R
= 1k
L
3.5
OUT+
IL = 0mA
5
mV
mA
OUT-
I
100
SC
RESTORE SECTION
, Comp
V
Composite Input Offset Voltage
Restoring Current Available
Power Supply Rejection Ratio
V
= 0V to +2.5V
REF
10
300
90
15
mV
µA
dB
µA
V
OS
I
OUT
PSRR
Ib V
V+ = 5V to 6V
70
V
Input Bias Current
V
= +2.5V
-0.8
-0.5
-0.2
0.8
REF
HOLD
REF
REF
V
HOLD Logic Input Low
H
V HOLD
HOLD Logic Input High
2.0
-15
-5
V
L
I
, Hold
IH
HOLD Input Current @ Logic High
HOLD Input Current @ Logic Low
Supply Current
V
V
V
= 5V
= 0V
= 0V
30
5
µA
µA
mA
HOLD
HOLD
HOLD
I , Hold
IL
I
17
20
23
S
AC Electrical Specifications
V
= +5V, V
REF
= 0V , R = 150Ω, R and R = 475Ω; A = 2, T = +25°C.
S
DC
L
F
G
V
A
PARAMETER
DESCRIPTION
CONDITION
MIN
TYP
MAX
UNITS
AMPLIFIER SECTION
SR
Slew Rate; 2V , 20% to 80%
P-P
300
3.2
V/µs
ns
tr, tf
Output Rise and Fall Times
Propagation Delay, IN+ to Output
Small Signal; Unity Gain
V
V
R
= 0.2Vp-p; 10% to 90%
= 0.2V; 10% to 10%
OUT
tpd
0.3
ns
OUT
-3dB BW
= 0; R = inf.; C = 0.6pF,
300
MHz
F
G
L
V
= 0.2V
OUT
P-P
Large Signal; Unity Gain
R
= 0; R = inf.; C = 0.6pF,
95
MHz
F
G
L
V
= 2V
OUT
P-P
Small Signal; A = +2
C = 0.6pF, V
= 0.2V
P-P
150
85
MHz
MHz
V
L
OUT
OUT
Large Signal; A = +2
V
C = 0.6pF, V
= 2V
P-P
L
FN6192.1
June 28, 2006
2
ISL4089
AC Electrical Specifications
V
= +5V, V
REF
= 0V , R = 150Ω, R and R = 475Ω; A = 2, T = +25°C. (Continued)
S
DC
L
F
G
V
A
PARAMETER
0.1dB BW
DESCRIPTION
0.1dB Gain Flatness; Unity Gain
CONDITION
MIN
TYP
MAX
UNITS
R
= 0; R = inf.; C = 0.6pF
70
MHz
F
G
L
V
= 0.2V
OUT
P-P
R
= 0; R = inf.; C = 0.6pF
60
MHz
F
G
L
V
= 2V
OUT
P-P
0.1dB Gain Flatness; A = +2
V
C = 0.6pF, V
= 0.2V
P-P
80
50
MHz
MHz
%
L
OUT
OUT
C = 0.6pF, V
= 2V
P-P
L
dG
Differential Gain Error
Differential Phase Error
NTC-7, Restore on sync tip
NTC-7, Restore on sync tip
0.03
0.05
dP
°
RESTORE SECTION
T
T
Time to Enable Hold; 50% to 50%
Time to Disable Hold; 50% to 50%
HOLD input 0V to +5V
HOLD input 5V to 0V
40
20
ns
ns
HE
HD
NOTE:
1. If an input signal is applied before the supplies are powered up, the input current must be limited to these maximum values
Typical Performance Curves V = +5V, R = 150Ω to GND, C = 0.6pF, T = 25°C, unless otherwise specified.
S
L
L
A
10
8
10
8
V
= 2V
V
R
= 0.2V
P-P
A
R
= 2
= R = 475Ω
OUT
P-P
OUT
= 150Ω
V
R = 150Ω
A
R
= 1
= 0Ω
L
L
F
G
V
F
6
6
4
4
A
R
= 2
= R = 475Ω
G
V
2
2
F
A
R
= 1
= 0Ω
V
0
0
F
-2
-4
-2
-4
A =4
V
-6
-6
A
R
R
= 4
= 475Ω
= 158Ω
V
R
R
= 475Ω
= 158Ω
F
G
F
G
-8
-8
-10
-10
1M
10M
100M
500M
1M
10M
100M
500M
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 1. SMALL SIGNAL GAIN vs FREQUENCY for
VARIOUS GAINS
FIGURE 2. LARGE SIGNAL GAIN vs FREQUENCY for
VARIOUS GAINS
10
10
V
R
= 2V
= 150Ω
V
= 0.2V
P-P
8
6
4
2
0
8
6
4
2
0
OUT
P-P
OUT
= 150Ω
A
= 1
V
R
L
L
C = 0.6pF to 22pF
L
AV = 2
R
= R = 1kΩ
G
F
R
= R = 475Ω
G
F
A
= 2
V
C = 22pF
L
-2
-4
-2
-4
A
= 2
R
= R = 301Ω
G
-6
V
-6
F
C = 0.6pF
L
-8
-8
-10
-10
1M
10M
FREQUENCY (Hz)
100M
500M
1M
10M
FREQUENCY (Hz)
100M
500M
FIGURE 4. SMALL SIGNAL GAIN vs R , R
FIGURE 3. LARGE SIGNAL GAIN vs FREQUENCY vs C
F
G
L
FN6192.1
June 28, 2006
3
ISL4089
Typical Performance Curves V = +5V, R = 150Ω to GND, C = 0.6pF, T = 25°C, unless otherwise specified. (Continued)
S
L
L
A
0.025
0.02
0.015
0.01
0.005
0
0.2
0.1
0
A
R
R
= 2
= R = 475
= 150
V
F
L
V
= 0.6V
P-P
OUT
G
V
= 0.2V
P-P
OUT
-0.005
-0.01
-0.015
-0.02
-0.025
V
= 0.3V
P-P
OUT
-0.1
-0.2
R
A
= 150
= 2
L
V
V
OUT
= 2V
P-P
-0.3
-0.4
f = 3.58MHz
= R = 475Ω
0.01
0.08
0.06
0.04
0.02
0
-0.02
-0.04
-0.06
-0.08
R
F
G
V
= 0.6V
P-P
OUT
-0.5
-0.6
-0.7
V
= 0.3V
P-P
OUT
-0.10
-0.8
0
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
DC (V)
1M
10M
100M
1G
V
FREQUENCY (Hz)
OUT
FIGURE 6. DIFFERENTIAL GAIN - PHASE
FIGURE 5. 0.1dB GAIN FLATNESS
1.05
4.0
3.5
V
= 2V
P-P
V
= 0.2V
OUT
OUT
P-P
1.0
R
= R = 475Ω
R
= R = 475Ω
F
G
F
G
0.95
C
= 0.5pF
C
= 0.5pF
3.0
2.5
2.0
1.5
1.0
0.5
0
G
G
0.9
0.85
0.8
0.75
0.7
0.65
TIME (20ns/DIV)
TIME (20ns/DIV)
FIGURE 7. SMALL SIGNAL TRANSIENT RESPONSE; A = 2
V
FIGURE 8. LARGE SIGNAL TRANSIENT RESPONSE; A = 2
V
60
50
40
30
20
10
0
100
1k
10k
100k
FREQUENCY (Hz)
FIGURE 9. INPUT NOISE vs FREQUENCY
FN6192.1
June 28, 2006
4
ISL4089
Typical Performance Curves V = +5V, R = 150Ω to GND, C = 0.6pF, T = 25°C, unless otherwise specified. (Continued)
S
L
L
A
JEDEC JESD51-7 HIGH EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
JEDEC JESD51-3 LOW EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
1
0.8
0.6
0.4
0.2
0
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
909mW
625mW
0
25
50
75 85 100
125
150
0
25
50
75 85 100
125
150
AMBIENT TEMPERATURE (°C)
AMBIENT TEMPERATURE (°C)
FIGURE 10. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
FIGURE 11. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
ISL4089
(8 LD SOIC)
EQUIVALENT
CIRCUIT
PIN NAME
DESCRIPTION
1
2
3
4
5
6
7
8
IN-
N+
Circuit 1
Circuit 1
Circuit 1
Circuit 2
Circuit 4
Circuit 1
Circuit 3
Circuit 4
V+
Video amplifier inverting input
Video amplifier non-inverting input
Restore amplifier V input
V
REF
REF
HOLD
GND
NIC
Hold/restore logic input. Logic “0” selects the restore state; logic “1” selects the hold state
Ground
No internal connection
Video amplifier output
Positive power supply
V
OUT
V+
V+
21k
IN
LOGIC PIN
V-
GND
CIRCUIT 1
CIRCUIT 2
V+
V+
CAPACITIVELY
COUPLED
ESD CLAMP
OUT
GND
GND
CIRCUIT 4
CIRCUIT 3
FN6192.1
June 28, 2006
5
ISL4089
DC-Restore Amplifier (Figure 13)
AC Test Circuits
The DC-restore circuit contains a voltage reference amplifier
and an analog switch function that closes the DC-restore
loop under control of the HOLD logic input. The reference
amplifier uses an internal 10mV offset voltage (V2) to enable
R
R
F
G
TEST
EQUIPMENT
R
-
S
V
+
IN
50Ω
118Ω
86.6Ω
the V
input to sense down to the negative supply. The A2
50Ω
REF
C
L
amplifier output stage operates in a current-feed mode with a
source/sink capability of ±300µA (Typ).
1. HOLD INPUT = 1
A logic “0” at the HOLD input closes switch S1 which closes
the DC-restore loop. The video input AC coupling capacitor,
CX1, acts as a DC hold capacitor (through the 75Ω
FIGURE 12A. VIDEO AMPLIFIER AC TEST CIRCUIT FOR 50Ω
R
R
F
termination resistor RX1) to average the current-source
output of amplifier A2. When the DC-restore loop has
reached equilibrium, the DC voltage stored on CX1 will the
G
TEST
EQUIPMENT
R
-
S
V
value required to force the output voltages at A1 (V
A2 (V ) according to the following:
IN+
) and
OUT
+
IN
75Ω
75Ω
C
L
75Ω
V
(DC) = V
+ 10mV
REF
(EQ. 2)
OUT
1. HOLD INPUT = 1
FIGURE 12B. BACKTERMINATED TEST CIRCUIT FOR VIDEO
CABLE APPLICATION.
and; the DC voltage at the non-inverting input of the video
amplifier A1 is given in Equation 3:
Figure 12A illustrates the AC test circuit used to operate the
video amplifier into a 150Ω load while providing a 50Ω
matched impedance. Figure 12B illustrates the test circuit for
impedance matching to 75Ω test equipment.
V
= V
(DC) + 1.2V
OUT
(EQ. 3)
IN+
Therefore, if V
is set to 0V (GND); V = 10mV, and
OUT
REF
the DC voltage stored on CX1 is ~1.2V.
Application Information
The CX1 capacitor value is chosen from the system
requirements. A typical DC-restore application using the
horizontal sync to drive the HOLD pin will result in a 62µs
hold time. The typical input bias current to the video amplifier
is 1.2µA, so for a 62µs hold time, and a 0.01µF capacitor, the
output voltage drift is 7.5mV in one line. The restore amplifier
can provide a typical current of 300µA to charge capacitor
CX1, so with a 1.2µs sampling time, the output can be
corrected by 36mV in each line.
General
The ISL4089 implements the video DC-restore function
using a high performance gain adjustable video amplifier
and a nulling, sample-hold amplifier to establish a user
defined DC reference voltage at the video amplifier output. A
detailed description of the DC-restore function implemented
in the ISL4089 can be found in application note AN1089,
EL4089 and EL4390 DC-Restored Video Amplifier. The
ISL4089 performs the same function with the exception that
it is designed for single supply operation.
Using a smaller value of CX1 increases both the voltage that
can be corrected, as well as the droop while being held.
Likewise, using a larger value of CX1, reduces the correction
and droop voltages. A sample of charging and droop rates
are shown on the following table.
Video Amplifier Operation (Figure 13)
The ISL4089 video amplifier (A1) is voltage-feed, high
performance video amplifier designed for +5V operation.
The output stage is capable of swinging to within 10mV of
the negative rail. The differential input stage contains an
internal voltage reference that positions the non-inverting
input DC level (V1) to ~1.2V higher than the negative supply
rail. This offset ensures that the amplifier input DC level is
maintained within the common mode input voltage range.
The amplifier non-inverting gain is given in Equation 1.
TABLE OF CHARGE STORAGE CAPACITOR VS DROOP
CHARGING RATES (NOTE)
DROOP IN
62µs
CHARGE IN
1.2µs
CHARGE IN
4µs
CAP VALUE
(if)
(mV)
(mV)
(mV)
10
33
7.5
2.3
36
11
120
36
R
⎛
⎞
⎟
⎠
100
0.75
3.6
12
F
V
= (V
– 1.2V) • 1 + --------
⎜
IN+
(EQ.1)
OUT
R
⎝
G
NOTE: Basic formulae are: V (droop) = Ib+ * (Line time - Sample
time)/Capacitor and V (charge) = I * Sample time/Capacitor
OUT
FN6192.1
June 28, 2006
6
ISL4089
R
R
F
G
475Ω
475Ω
ISL4089
VIDEO
OUT
V
IN-
RXT
-
VIDEO
INPUT
75Ω
A1
CX1
V
1.2V
IN+
-
+
+
V
OUT
V1
RX1
75Ω
S1
4k
V+
+5V
0.1µF
4.7µF
A2
GND
-
+
V
REF
10mV
V2
-
-
+
40pF
V
Ref
0V to +4.5V
GND
HOLD
TTL
INPUT
FIGURE 13. BASIC +5V APPLICATION CIRCUIT
Using the Reference Voltage Input (V
)
Application Information
REF
Implementing DC-restore and amplifying composite video
using a single +5V supply amplifier, requires attention to the
performance of the amplifier over the minimum to maximum
range of output voltage swing. The differential gain - phase
plot in Figure 6 shows the amplifier accuracy operating from
A typical single supply application circuit using the EL1883
sync separator to generate the DC-restore hold command, is
shown in Figure 13. The ISL4089 is configured for a gain of
2, and 75Ω input and output terminations are used for cable
driving; providing an end to end gain of 1. DC-restore is
performed during sync tip using the composite sync output
of the EL1883, which clamps the -300mV input sync tip level
to 0VDC at the ISL4089 output (Figure 15 - lower trace).
Clamping sync tip to 0VDC forces the black level, color burst
and active video to the +300mV level at the 75Ω load in the
terminal equipment, and to +600mV at the ISL4089 output
pin. The +600mV DC offset is safely within the lower linear
range of the ISL4089 output (Figure 6 - Differential Gain -
Phase) and the 2V maximum video amplitude at the output
is safely within the upper limit. In applications where the sync
tip level can’t be guaranteed, positioning the active video
within the linear range can be accomplished using the back
porch clamp output of the EL1883 and supplying +1V to the
a single +5V supply, driving a 300mV
and a 600mV
P-P
P-P
signal into a 150Ω load. Over the output DC voltage range of
0.5V to 3.25V, differential gain and phase are less than
0.05% and 0.05° respectively and defines the optimum
output voltage range of the ISL4089. Figure 6 also shows
that as the signal level increases, a corresponding decrease
in the output DC level (min/max voltage swing) can be
expected. The V
input enables the output DC voltage
REF
level to be optimally programmed within the min/max voltage
range, according to Equation 2. The values in Figure 6 take
into account the additional amplifier overhead (300mV
P-P
) needed by the video signal. Although the
and 600mV
P-P
AC performance degrades below ~0.5V, the ISL4089
maintains DC accuracy down to 10mV.
V
input. This has the effect of clamping the back porch to
REF
the +1V V
level at the output while enabling the negative
REF
sync tip level to pass through to the output.
Limiting the Output Current
No output short circuit current limit exists on these parts. All
applications need to limit the output current to less than
60mA. Adequate thermal heat sinking of the parts is also
required.
FN6192.1
June 28, 2006
7
ISL4089
R5
R4
475 ohms
475 ohms
+5V
ISL4089
1
C2, C3
0.1uF
C1
4.7uF
IN-
V+
C4
0.01uF
-
VIDEO
INPUT
Ground
+
2
R6
75 ohms
R3
75 ohms
IN+
Vout
Out
3
+
Vref
NC
4
GND
Hold
Composite Sync
Out
Back-porch Clamp
Out
EL1883
1
2
3
4
8
7
6
5
C5
0.1uF
Horizontal Sync
Out
Vertical Sync
Out
R7
681K
C6
0.056 uF
FIGURE 14. APPLICATION CIRCUIT USING THE EL1883 SYNC SEPARATOR TO GENERATE DC-RESTORE HOLD CONTROL
COMPOSITE VIDEO INPUT
0VDC
COMPOSITE SYNC INPUT
0VDC
DC-RESTORED VIDEO OUTPUT
0VDC
FIGURE 15. DC-RESTORE USING COMPOSITE SYNC AND V
= 0VDC
REF
FN6192.1
June 28, 2006
8
ISL4089
Small Outline Package Family (SO)
A
D
h X 45°
(N/2)+1
N
A
PIN #1
I.D. MARK
E1
E
c
SEE DETAIL “X”
1
(N/2)
B
L1
0.010 M
C A B
e
H
C
A2
A1
GAUGE
PLANE
SEATING
PLANE
0.010
L
4° ±4°
0.004 C
b
0.010 M
C
A
B
DETAIL X
MDP0027
SMALL OUTLINE PACKAGE FAMILY (SO)
SO16
(0.150”)
SO16 (0.300”)
(SOL-16)
SO20
SO24
(SOL-24)
SO28
(SOL-28)
SYMBOL
SO-8
0.068
0.006
0.057
0.017
0.009
0.193
0.236
0.154
0.050
0.025
0.041
0.013
8
SO-14
0.068
0.006
0.057
0.017
0.009
0.341
0.236
0.154
0.050
0.025
0.041
0.013
14
(SOL-20)
0.104
0.007
0.092
0.017
0.011
0.504
0.406
0.295
0.050
0.030
0.056
0.020
20
TOLERANCE
MAX
NOTES
A
A1
A2
b
0.068
0.006
0.057
0.017
0.009
0.390
0.236
0.154
0.050
0.025
0.041
0.013
16
0.104
0.007
0.092
0.017
0.011
0.406
0.406
0.295
0.050
0.030
0.056
0.020
16
0.104
0.007
0.092
0.017
0.011
0.606
0.406
0.295
0.050
0.030
0.056
0.020
24
0.104
0.007
0.092
0.017
0.011
0.704
0.406
0.295
0.050
0.030
0.056
0.020
28
-
±0.003
±0.002
±0.003
±0.001
±0.004
±0.008
±0.004
Basic
-
-
-
c
-
D
1, 3
E
-
E1
e
2, 3
-
L
±0.009
Basic
-
L1
h
-
Reference
Reference
-
N
-
Rev. L 2/01
NOTES:
1. Plastic or metal protrusions of 0.006” maximum per side are not included.
2. Plastic interlead protrusions of 0.010” maximum per side are not included.
3. Dimensions “D” and “E1” are measured at Datum Plane “H”.
4. Dimensioning and tolerancing per ASME Y14.5M-1994
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN6192.1
June 28, 2006
9
相关型号：
ISL41334IRZA
LINE TRANSCEIVER, PQCC40, 6 X 6 MM, ROHS COMPLIANT, PLASTIC, MO-220VJJD, QFN-40
RENESAS
©2020 ICPDF网 联系我们和版权申明