30CTQ [INFINEON]
SCHOTTKY RECTIFIER; 肖特基整流器器
Infineon 
Bulletin PD-20606 rev. B 01/04
30CTQ...
30CTQ...S
30CTQ...-1
SCHOTTKY RECTIFIER
30 Amp
Description/ Features
Major Ratings and Characteristics
This center tap Schottky rectifier series has been optimized
for low reverse leakage at high temperature. The proprietary
barrier technology allows for reliable operation up to 175°C
junction temperature. Typical applications are in switching
power supplies, converters, free-wheeling diodes, and re-
verse battery protection.
Characteristics
Values
Units
I
Rectangular
waveform
30
A
F(AV)
V
I
80 -100
850
V
A
V
175° C T operation
RRM
J
Center tap configuration
Low forward voltage drop
@ tp=5µssine
FSM
High purity, high temperature epoxy encapsulation for
V
@15Apk, T =125°C
J
(per leg)
0.67
enhanced mechanical strength and moisture resistance
F
High frequency operation
Guard ring for enhanced ruggedness and long term
T
range
-55to175
°C
J
reliability
Case Styles
30CTQ...
30CTQ... -1
30CTQ... S
Base
Common
Cathode
2
Base
Common
Cathode
2
Base
Common
Cathode
2
2
2
2
1
1
Common
Cathode
Common
Cathode
3
3
1
Common
Cathode
3
Anode
Anode
Anode
Anode
Anode
Anode
TO-220
D2PAK
TO-262
1
www.irf.com
30CTQ..., 30CTQ...S, 30CTQ...-1
Bulletin PD-20606 rev. B 01/04
Voltage Ratings
30CTQ80
30CTQ80S
30CTQ80-1
30CTQ100
30CTQ100S
30CTQ100-1
Parameters
VR
Max. DC Reverse Voltage (V)
80
100
VRWM Max. Working Peak Reverse Voltage (V)
Absolute Maximum Ratings
Parameters
IF(AV) Max. Average Forward (Per Leg)
Values Units
Conditions
15
A
50%duty cycle@TC =129°C,rectangular wave form
Current *SeeFig.5
IFSM Max. PeakOneCycleNon-Repetitive
(Per Device)
30
850
275
Following any rated
load condition and with
5µs Sineor3µsRect.pulse
10msSineor6msRect. pulse rated VRRM applied
A
SurgeCurrent (Per Leg) *SeeFig.7
EAS Non-Repetitive Avalanche Energy
(Per Leg)
7.50
mJ TJ = 25°C, IAS = 0.50Amps,L=60mH
IAR
Repetitive Avalanche Current
(Per Leg)
0.50
A
Current decaying linearly to zero in 1µsec
Frequency limited by TJ max.VA =1.5xVR typical
Electrical Specifications
Parameters
Values Units
Conditions
VFM Max. Forward Voltage Drop
0.86
1.05
0.67
0.82
0.55
7.0
V
V
V
@ 15A
@ 30A
@ 15A
TJ = 25 °C
(Per Leg) * See Fig. 1
(1)
TJ = 125 °C
V
@ 30A
IRM Max. Reverse Leakage Current
mA TJ = 25 °C
mA TJ = 125 °C
VR = rated VR
(Per Leg) * See Fig. 2
(1)
CT
LS
Max. Junction Capacitance(Per Leg)
Typical Series Inductance (Per Leg)
500
8.0
10000
pF VR = 5VDC (test signal range 100Khz to 1Mhz) 25°C
nH Measured lead to lead 5mm from package body
V/ µs
dv/dt Max. Voltage Rate of Change
(Rated VR)
(1) Pulse Width < 300µs, Duty Cycle <2%
Thermal-Mechanical Specifications
Parameters
Values Units
Conditions
TJ
Max. Junction Temperature Range
-55to175
-55to175
3.25
°C
°C
Tstg Max. Storage Temperature Range
RthJC Max. Thermal Resistance Junction
toCase (Per Leg)
°C/W DC operation
RthJC Max. Thermal Resistance Junction
toCase(Per Package)
RthCS Typical Thermal Resistance, Case
toHeatsink
1.63
0.50
°C/W DC operation
°C/W Mounting surface,smooth and greased
(only for TO-220)
wt
T
Approximate Weight
Mounting Torque
2(0.07) g(oz.)
Min.
Max.
6(5)
Kg-cm
(Ibf-in)
12(10)
2
www.irf.com
30CTQ..., 30CTQ...S, 30CTQ...-1
Bulletin PD-20606 rev. B 01/04
1000
100
10
100
T = 175°C
J
10
1
150°C
125°C
100°C
75°C
50°C
25°C
0.1
0.01
0.001
0.0001
0
20
40
60
80
100
Reverse Voltage - V (V)
R
Fig.2-Typical Values Of Reverse Current
Vs. Reverse Voltage (PerLeg)
Tj = 175˚C
Tj = 125˚C
Tj = 25˚C
1000
T = 25°C
J
100
1
0
20
40
60
80
100
0
0.5
1
1.5
2
2.5
Reverse Voltage - V (V)
Forward Voltage Drop-VFM (V)
R
Fig.1-Max. Forward Voltage Drop Characteristics
Fig.3-Typical Junction Capacitance
Vs. Reverse Voltage (PerLeg)
(PerLeg)
10
D = 0.75
D = 0.50
D = 0.33
1
D = 0.25
D = 0.20
P
DM
0.1
t
1
t
2
Notes:
0.01
Single Pulse
(Thermal Resistance)
1. Duty factor D = t / t
2
1
2. Peak T = PDMx Z
+ T
C
J
thJC
0.001
0.00001
0.0001
0.001
0.01
0.1
1
10
100
t
, Rectangular Pulse Duration (Seconds)
1
Fig.4-Max. Thermal Impedance ZthJC Characteristics (PerLeg)
www.irf.com
3
30CTQ..., 30CTQ...S, 30CTQ...-1
Bulletin PD-20606 rev. B 01/04
180
170
7
6
5
4
3
2
1
0
D = 0.20
D = 0.25
D = 0.33
D = 0.50
D = 0.75
DC
160
150
RMS Lim it
140
DC
Sq u a r e w a v e ( D = 0. 5 0)
130
120
110
100
80%Rated V applied
R
see note (2)
0
2
4
6
8
10 12 14
0
2
4
6
8
10
12
Average Forward Current - I (A)
Average Forward Current - I
(A)
F( AV)
F( AV)
Fig. 5-Max. Allowable CaseTemperature
Vs. Average Forward Current (PerLeg)
Fig.6-Forward Power Loss Characteristics
(PerLeg)
1000
At Any Rated Load Condition
And With Rated V Applied
RRM
Following Surge
100
10
100
1000
10000
Square Wave Pulse Duration - t (microsec)
p
Fig.7-Max. Non-Repetitive Surge Current (PerLeg)
L
HIG H- SPEED
SWITCH
IRFP460
DUT
FREE- WHEEL
DIODE
Rg = 25ohm
Vd = 25 Volt
+
C URRENT
MONITOR
40HFL40S02
Fig.8-Unclamped Inductive Test Circuit
(2) Formulaused:TC =TJ -(Pd+PdREV)xRthJC
;
Pd=ForwardPowerLoss=IF(AV) xVFM @(IF(AV) /D) (seeFig.6);
PdREV =InversePowerLoss=VR1 xIR (1-D); IR @VR1=10V
4
www.irf.com
30CTQ..., 30CTQ...S, 30CTQ...-1
Bulletin PD-20606 rev. B 01/04
Outline Table
10.54 (0.41)
MAX.
1.32 (0.05)
1.22 (0.05)
3.78 (0.15)
3.54 (0.14)
DIA.
6.48 (0.25)
6.23 (0.24)
2.92 (0.11)
2.54 (0.10)
TERM 2
15.24 (0.60)
14.84 (0.58)
2°
3
1 2
Base
Common
Cathode
14.09 (0.55)
13.47 (0.53)
3.96 (0.16)
3.55 (0.14)
0.10 (0.004)
2
2.04 (0.080) MAX.
1.40 (0.05)
2.89 (0.11)
1.15 (0.04)
2.64 (0.10)
0.94 (0.04)
0.69 (0.03)
2
1
Common
Cathode
3
Anode
Anode
3
2
1
0.61 (0.02) MAX.
4.57 (0.18)
4.32 (0.17)
Conform to JEDEC outline TO-220AB
5.08 (0.20) REF.
Dimensions in millimeters and (inches)
Base
Common
Cathode
2
2
1
Common
Cathode
3
Anode
Anode
Conform to JEDEC outline D2Pak (SMD-220)
Dimensions in millimeters and (inches)
www.irf.com
5
30CTQ..., 30CTQ...S, 30CTQ...-1
Bulletin PD-20606 rev. B 01/04
Outline Table
Base
Common
Cathode
2
2
1
Common
Cathode
3
Anode
Anode
Modified JEDEC outline TO-262
Dimensions in millimeters and (inches)
Marking Information
PART NUMBER
INTERNATIONAL
RECTIFIER
LOGO
EXAMPLE: THIS IS AN 30CTQ100
LOT CODE 1789
ASSEMBLED ON WW 19, 1998
IN THE ASSEMBLY LINE "C"
DATE CODE
YEAR 7 = 1998
WEEK 19
ASSEMBLY
LOT CODE
LINE C
6
www.irf.com
30CTQ..., 30CTQ...S, 30CTQ...-1
Bulletin PD-20606 rev. B 01/04
Tape & Reel Information
TRR
1.60 (0.063)
1.50 (0.059)
1.60 (0.063)
4.10 (0.161)
3.90 (0.153)
DIA.
1.50 (0.059)
0.368 (0.0145)
0.342 (0.0135)
FEED DIRECTION
TRL
1.85 (0.073)
1.65 (0.065)
11.60 (0.457)
11.40 (0.449)
24.30 (0.957)
15.42 (0.609)
23.90 (0.941)
15.22 (0.601)
1.75 (0.069)
DIA.
10.90 (0.429)
10.70 (0.421)
1.25 (0.049)
4.72 (0.186)
16.10 (0.634)
15.90 (0.626)
4.52 (0.178)
FEED DIRECTION
13.50 (0.532)
12.80 (0.504)
26.40 (1.039)
24.40 (0.961)
DIA.
SMD-220 Tape & Reel
When ordering, indicate the part
number, part orientation, and the
quantity. Quantities are in multiples
of 800 pieces per reel for both
TRL and TRR.
60 (2.362)
DIA. MIN.
360 (14.173)
DIA. MAX.
Dimensions in millimeters and (inches)
Ordering Information Table
Device Code
30
C
T
Q
100 - 1
1
2
3
4
5
6
1
2
3
4
5
6
-
-
-
-
-
-
Essential Part Number
C = Common Cathode
T = TO-220
Q = Schottky Q Series
Voltage Rating
080 = 80V
100 = 100V
1 = TO-262
S = D2Pak
www.irf.com
7
30CTQ..., 30CTQ...S, 30CTQ...-1
Bulletin PD-20606 rev. B 01/04
Data and specifications subject to change without notice.
This product has been designed and qualified for Industrial Level.
Qualification Standards can be found on IR's Web site.
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105
TAC Fax: (310) 252-7309
Visit us at www.irf.com for sales contact information. 01/04
8
www.irf.com
相关型号：
©2020 ICPDF网 联系我们和版权申明