MK3720BTRLF [IDT]
Clock Generator, 54MHz, CMOS, PDSO8, 0.150 INCH, SOIC-8;
| 型号： | MK3720BTRLF |
| 厂家： | 
INTEGRATED DEVICE TECHNOLOGY |
| 描述： | Clock Generator, 54MHz, CMOS, PDSO8, 0.150 INCH, SOIC-8 时钟 光电二极管 外围集成电路 晶体 |
| 文件： | 总6页 (文件大小：100K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MK3720
27 MHZ AND 54 MHZ 3.3 VOLT VCXO
The frequency of the on-chip VCXO is adjusted by an
external control voltage input into pin VIN. Because
Description
VIN is a high impedance input, it can be driven directly
from an PWM RC integrator circuit.
The MK3720D and MK3720B are drop-in replacements
for the MK3720S and MK3720A devices. Compared to
these earlier devices the MK3720D and MK3720B offer
a wider operating frequency range and improved power
supply noise rejection.
Features
• MK3720D and MK3720B are drop-in upgrades to the
earlier MK3720S and MK3720A devices
The MK3720 is a low-cost, low-jitter, high-performance
3.3 Volt VCXO designed to replace expensive 13.5, 27,
or 54 MHz VCXOs. The patented on-chip Voltage
Controlled Crystal Oscillator accepts a 0 to 3.3 V input
voltage to cause the output clocks to vary by 100 ppm.
Using ICS’ patented VCXO and analog/digital
Phase-Locked Loop (PLL) techniques, the device uses
an inexpensive external pullable crystal input to
produce output clocks of 13.5 MHz, 27 MHz, and 54
MHz.
• Packaged in 8-pin SOIC
• Available in Pb (lead) free package (MK3720D only)
• Operating voltage of 3.3 V ( 5%)
• Output clocks of 54, 27, and 13.5 MHz
• Uses an inexpensive 13.500 MHz external crystal
• On-chip VCXO (patented) with pull range of 200ppm
(minimum)
• VCXO tuning voltage of 0 to 3.3V
The MK3720D exhibits a moderate VCXO gain of 120
ppm/V typical, when used with a high-quality external
pullable quartz crystal. The MK3720B offers a higher
VCXO gain of 150 ppm/V, similar to the earlier
MK3720A. The higher intrinsic VCXO gain of the
MK3720B may help compensate for the reduced
pullability of a low quality crystal used in some
applications. However, higher VCXO gain may also
increase clock output phase noise.
• 12 mA output drive capability at TTL levels
• Advanced, low-power, sub-micron CMOS process
MK3720D is Recommended for New Designs
Block Diagram
VDD
VIN
54 M Hz
PLL/Clock
Synthesis
Circuitry
X1
13.5 M Hz
Pullable
Voltage
Controlled
Crystal
Oscillator
27 M Hz
Crystal
X2
13.5 M Hz
GND
MDS 3720 H
1
Revision 052504
Integrated Circuit Systems ● 525 Race Street, San Jose, CA 95126 ● tel (408) 297-1201 ● www.icst.com
MK3720
27 MHZ AND 54 MHZ 3.3 VOLT VCXO
Pin Assignment
X 1
V D D
V I N
8
7
6
5
1
2
3
4
X 2
2 7 M
13.5M
5 4 M
G N D
M K 3 7 2 0 B
M K 3 7 2 0 D
8 P i n ( 1 5 0 m i l ) S O I C
Pin Descriptions
Pin
Number
Pin
Name
Pin
Type
Pin Description
1
2
3
XI
Input Crystal connection. Connect to the external pullable crystal.
Power Connect to +3.3 V (0.01uf decoupling capacitor recommended).
VDD
VIN
Input Voltage input to VCXO. Zero to 3.3 V analog input which controls the
oscillation frequency of the VCXO.
4
5
6
7
8
GND
54M
13.5
27
Power Connect to ground.
Output 54 MHz VCXO clock output.
Output 13.5 MHz VCXO clock output.
Output 27 MHz VCXO clock output.
X2
Input Crystal connection. Connect to the external pullable crystal.
MDS 3720 H
2
Revision 052504
Integrated Circuit Systems ● 525 Race Street, San Jose, CA 95126 ● tel (408) 297-1201 ● www.icst.com
MK3720
27 MHZ AND 54 MHZ 3.3 VOLT VCXO
The frequency of oscillation of a quartz crystal is
determined by its “cut” and by the load capacitors
connected to it. The MK3720 incorporates on-chip
variable load capacitors that “pull” (change) the
frequency of the crystal. The crystal specified for use
with the MK3720 is designed to have zero frequency
error when the total of on-chip + stray capacitance is
14 pF.
External Component Selection
The MK3720 requires a minimum number of external
components for proper operation.
Decoupling Capacitor
A decoupling capacitor of 0.01µF must be connected
between VDD (pin 2) and GND (pin 4), as close to
these pins as possible. For optimum device
performance, the decoupling capacitor should be
mounted on the component side of the PCB. Avoid the
use of vias in the decoupling circuit.
Recommended Crystal Parameters:
See application note MAN05 for crystal information.
MAN05 is available on the internet at
www.icst.com/pdf/man05.pdf.
Series Termination Resistor
The external crystal must be connected as close to the
chip as possible and should be on the same side of the
PCB as the MK3720. There should be no via’s between
the crystal pins and the X1 and X2 device pins. There
should be no signal traces underneath or close to the
crystal.
When the PCB trace between the clock output (CLK,
pin 5) and the load is over 1 inch, series termination
should be used. To series terminate a 50Ω trace (a
commonly used trace impedance) place a 33Ω resistor
in series with the clock line, as close to the clock output
pin as possible. The nominal impedance of the clock
output is 20Ω.
Crystal Tuning Load Capacitors
The crystal traces should include pads for small fixed
capacitors, one between X1 and ground, and another
between X2 and ground. Stuffing of these capacitors
on the PCB is optional. The need for these capacitors is
determined at system prototype evaluation, and is
influenced by the particular crystal used (manufacture
and frequency) and by PCB layout. The typical required
capacitor value is 1 to 4 pF.
Quartz Crystal
The MK3720 VCXO function consists of the external
crystal and the integrated VCXO oscillator circuit. To
assure the best system performance (frequency pull
range) and reliability, a crystal device with the
recommended parameters (shown below) must be
used, and the layout guidelines discussed in the
following section shown must be followed.
The procedure for determining the value of these
capacitors can be found in application note MAN05.
MDS 3720 H
3
Revision 052504
Integrated Circuit Systems ● 525 Race Street, San Jose, CA 95126 ● tel (408) 297-1201 ● www.icst.com
MK3720
27 MHZ AND 54 MHZ 3.3 VOLT VCXO
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the MK3720. These ratings,
which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of
the device at these or any other conditions above those indicated in the operational sections of the
specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can
affect product reliability. Electrical parameters are guaranteed only over the recommended operating
temperature range.
Item
Rating
Supply Voltage, VDD
All Inputs and Outputs
7 V
-0.5 V to VDD+0.5 V
0 to +70°C
Ambient Operating Temperature
Storage Temperature
-65 to +150°C
260°C
Soldering Temperature
Recommended Operation Conditions
Parameter
Min.
Typ.
Max.
+70
Units
°C
Ambient Operating Temperature
Power Supply Voltage (measured in respect to GND)
Reference crystal parameters
0
–
+3.15
+3.45
V
Refer to page 3
Thermal Characteristics
Parameter
Symbol
Conditions
Min.
Typ. Max. Units
Thermal Resistance Junction to
Ambient
θ
θ
θ
θ
Still air
150
140
120
40
°C/W
°C/W
°C/W
°C/W
JA
JA
JA
JC
1 m/s air flow
3 m/s air flow
Thermal Resistance Junction to Case
MDS 3720 H
4
Revision 052504
Integrated Circuit Systems ● 525 Race Street, San Jose, CA 95126 ● tel (408) 297-1201 ● www.icst.com
MK3720
27 MHZ AND 54 MHZ 3.3 VOLT VCXO
DC Electrical Characteristics
VDD=3.3 V 5% , Ambient temperature 0 to +70°C, unless stated otherwise
Parameter
Symbol
Conditions
Min.
3.15
2.4
Typ.
Max.
Units
Operating Voltage
VDD
3.45
V
V
V
V
Output High Voltage
Output Low Voltage
V
I
I
I
= -12 mA
= 12 mA
= -4 mA
OH
OH
OL
OH
V
0.4
OL
Output High Voltage (CMOS
Level)
V
VDD-0.4
OH
Operating Supply Current
Short Circuit Current
IDD
No load
13
50
mA
mA
V
I
OS
VIN, VCXO Control Voltage
V
0
3.3
IA
AC Electrical Characteristics
VDD = 3.3 V 5%, Ambient Temperature 0 to +70° C, unless stated otherwise
Parameter
Crystal Pullability
VCXO Gain
Symbol
Conditions
Min. Typ. Max. Units
F
0V< VIN < 3.3V, Note 1
+ 115
ppm
P
MK3720D, Note 3
MK3720B, Note 3
Output Rise Time
Output Fall Time
Output Clock Duty Cycle
VIN = VDD/2 +1 V, Note 1
VIN = VDD/2 +1 V, Note 1
120
150
ppm/V
ppm/V
ns
t
0.8 to 2.0 V, C =15 pF
1.5
1.5
55
OR
L
t
2.0 to 0.8 V, C =15 pF
ns
OF
L
t
Measured at 1.4 V, C =15 pF
45
50
80
%
D
L
Maximum Output Jitter,
short term
t
C =15 pF, 13.5M CLK
ps
J
L
C =15 pF, 27M and 54M CLK
150
ps
L
Note 1: External crystal device must conform with Pullable Crystal Specifications listed on page 3.
Note 2: Original MK3720S and MK3720A provided +100 ppm crystal pullability.
Note 3: Original MK3720S and MK3720A provided 100 and 170 ppm/V respectively.
MDS 3720 H
5
Revision 052504
Integrated Circuit Systems ● 525 Race Street, San Jose, CA 95126 ● tel (408) 297-1201 ● www.icst.com
MK3720
27 MHZ AND 54 MHZ 3.3 VOLT VCXO
Package Outline and Package Dimensions (8-pin SOIC, 150 Mil. Narrow Body)
Package dimensions are kept current with JEDEC Publication No. 95
Millimeters
Inches
Min Max
0.0532 0.0688
0.0040 0.0098
Symbol
Min
Max
1.75
0.25
0.51
0.25
5.00
4.00
A
A1
B
C
D
E
e
1.35
1.10
0.33
0.19
4.80
3.80
0.013
0.0075 0.0098
.1890 .1968
0.020
Index
Area
0.1497 0.1574
0.050 Basic
E
H
1.27 Basic
H
h
L
5.80
0.25
0.40
0°
6.20
0.50
1.27
8°
0.2284 0.2440
0.010
0.016
0°
0.020
0.050
8°
a
Pin 1
D
h x 450
A
Q
c
e
b
Ordering Information
Part / Order Number
(Note 1)
Marking
Shipping Packaging
Package
Temperature
MK3720D
MK3720D
MK3720D
MK3720DL
MK3720DL
MK3720B
MK3720B
Tubes
Tape and Reel
Tubes
Tape and Reel
Tubes
8-pin SOIC
8-pin SOIC
8-pin SOIC
8-pin SOIC
8-pin SOIC
8-pin SOIC
0 to +70° C
0 to +70° C
0 to +70° C
0 to +70° C
0 to +70° C
0 to +70° C
MK3720DTR
MK3720DLF
MK3720DLFTR
MK3720B
MK3720BTR
Tape and Reel
Note 1: MK3720D is recommended for new designs. Call factory for information on MK3720A and MK3720S.
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems (ICS)
assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would
result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial
applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary
environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any
circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or
critical medical instruments.
MDS 3720 H
6
Revision 052504
Integrated Circuit Systems ● 525 Race Street, San Jose, CA 95126 ● tel (408) 297-1201 ● www.icst.com
相关型号：
©2020 ICPDF网 联系我们和版权申明