IDT74CBTLVR3862PY [IDT]
LOW-VOLTAGE 10-BIT BUS SWITCH WITH ACTIVE HIGH AND LOW ENABLES; 具有活性高,低低压10位总线开关启用型号: | IDT74CBTLVR3862PY |
厂家: | INTEGRATED DEVICE TECHNOLOGY |
描述: | LOW-VOLTAGE 10-BIT BUS SWITCH WITH ACTIVE HIGH AND LOW ENABLES |
文件: | 总5页 (文件大小:57K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LOW-VOLTAGE 10-BIT
IDT74CBTLVR3862
BUS SWITCH WITH ACTIVE
HIGH AND LOW ENABLES
DESCRIPTION:
FEATURES:
TheCBTLVR3862isatenbit high-speedbusswitch. Itaddsaninternal
series resistor with each switch to reduce reflection noise in high-speed
applications. Whenclosed,theswitchactsasasource(series)termination
for the driver connected to it.
• Isolation Under Power-Off Conditions
• Over-voltage tolerant
• Latch-up performance exceeds 100mA
• VCC = 2.3V - 3.6V, normal range
The device is organized as one 10-bit bus switch. The switches are
controlled by independent active-low enable (OE) and active-high enable
(OE) controls.
• ESD >2000V per MIL-STD-883, Method 3015; >200V using
machine model (C = 200pF, R = 0)
• Available in SSOP, QSOP, and TSSOP packages
To ensure the high-impedance state during power up or power down,
OE should be tied to VCC through a pullup resistor; the minimum value of
theresistorisdeterminedbythecurrent-sinkingcapabilityofthedriver,and
OE should be tied to GND.
APPLICATIONS:
• 3.3V High Speed Bus Switching and Bus Isolation
FUNCTIONALBLOCKDIAGRAM
SIMPLIFIEDSCHEMATIC,EACH
SWITCH
2
22
A1
B1
SW
11
13
A10
B10
SW
B
A
1
OE
OE
23
OE
OE
TheIDTlogoisaregisteredtrademarkofIntegratedDeviceTechnology,Inc.
INDUSTRIAL TEMPERATURE RANGE
AUGUST 2002
1
c
2002 Integrated Device Technology, Inc.
DSC-5867/7
IDT74CBTLVR3862
INDUSTRIALTEMPERATURERANGE
LOW-VOLTAGE10-BITBUSSWITCHWITHACTIVEHIGHANDLOWENABLES
ABSOLUTEMAXIMUMRATINGS(1)
PINCONFIGURATION
Symbol Description
Max.
–0.5to4.6
–0.5to4.6
128
Unit
V
VCC
VI
SupplyVoltageRange
1
24
23
22
21
20
19
18
17
16
15
14
13
VCC
OE
B1
B2
OE
A1
InputVoltageRange
V
ContinuousChannelCurrent
Input Clamp Current, VI/O < 0
StorageTemperatureRange
mA
mA
°C
2
IIK
–50
A2
3
TSTG
–65to+150
A3
4
NOTE:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
A4
5
B3
B4
B5
A5
6
A6
7
A7
8
B6
B7
B8
A8
9
A9
10
11
12
A10
GND
B9
B10
FUNCTIONTABLE(1)
Inputs
SSOP/ QSOP/ TSSOP
TOP VIEW
OE
L
OE
L
Function
Disconnect
L
H
Disconnect
H
L
A Port = B Port
Disconnect
H
H
NOTE:
1. H = HIGH Voltage Level
= LOW Voltage Level
L
OPERATINGCHARACTERISTICS(1)
Symbol
Parameter
Test Conditions
Min.
Max.
Unit
V
VCC
SupplyVoltage
2.3
1.7
2
3.6
—
VIH
High-LevelControlInputVoltage
Low-LevelControlInputVoltage
OperatingFree-AirTemperature
VCC = 2.3V to 2.7V
VCC = 2.7V to 3.6V
VCC = 2.3V to 2.7V
VCC = 2.7V to 3.6V
V
—
VIL
TA
—
0.7
0.8
+85
V
—
–40
°C
NOTE:
1. All unused control inputs of the device must be held at VCC or GND to ensure proper device operation.
2
IDT74CBTLVR3862
INDUSTRIALTEMPERATURERANGE
LOW-VOLTAGE10-BITBUSSWITCHWITHACTIVEHIGHANDLOWENABLES
DCELECTRICALCHARACTERISTICSOVEROPERATINGRANGE
FollowingConditionsApplyUnlessOtherwiseSpecified:
Operating Condition: TA = –40°C to +85°C
Symbol
VIK
Parameter
Test Conditions
Min.
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Typ.(1)
—
—
—
—
—
—
4
Max.
–1.2
±1
5
Unit
V
ControlInputs, DataI/O
ControlInputs
Data I/O
VCC = 3V, II = –18mA
II
VCC = 3.6V, VI = VCC or GND
VCC = 3.6V, VO = 0V or 3.6V switch disabled
VCC = 0V, VI or VO = 0V or 3.6V
VCC = 3.6V, IO = 0, VI = VCC or GND
VCC = 3.6V, one input at 3V, other inputs at VCC or GND
VI = 3V or 0
µA
µA
µA
µA
µA
pF
IOZ
IOFF
ICC
10
10
(2)
∆ICC
ControlInputs
ControlInputs
300
—
CI
CIO(OFF)
VO = 3V or 0, OE = VCC, OE = VCC
8
—
pF
VCC = 2.3V
VI = 0
IO = 64mA
IO = 24mA
IO = 15mA
IO = 64mA
IO = 24mA
IO = 15mA
30
30
36
30
30
32
47
Typ. at VCC = 2.5V
47
(3)
RON
VI = 1.7V
VI = 0
80
Ω
42
VCC = 3V
42
VI = 2.4V
47
NOTES:
1. Typical values are at 3.3V, +25°C ambient.
2. The increase in supply current is attributable to each input that is at the specified voltage level rather than VCC or GND.
3. This is measured by the voltage drop between the A and B terminals at the indicated current through the switch. On-state resistance is determined by the lower of the voltages
of the two (A or B) terminals.
SWITCHINGCHARACTERISTICS
VCC = 2.5V ± 0.2V
VCC = 3.3V ± 0.3V
Min. Max.
Symbol
Parameter
Min.
Max.
Unit
(1)
tPD
PropagationDelay
A to B or B to A
OutputEnableTime
OE to A or B
—
1
0.9
—
1.5
5.3
5.5
5.3
6
ns
tEN
tDIS
tEN
6
5.5
6
1
ns
ns
ns
ns
OutputDisableTime
OE to A or B
1
1
OutputEnableTime
OE to A or B
1
1
tDIS
OutputDisableTime
OE to A or B
1
5.5
1
NOTE:
1. The propagation delay is the calculated RC time constant of the typical on-state resistance of the switch and the specified load capacitance when driven by an ideal voltage source
(zero output impededance).
3
IDT74CBTLVR3862
INDUSTRIALTEMPERATURERANGE
LOW-VOLTAGE10-BITBUSSWITCHWITHACTIVEHIGHANDLOWENABLES
TEST CIRCUITS AND WAVEFORMS
TESTCONDITIONS
VIH
VT
0V
SAME PHASE
INPUT TRANSITION
Symbol
VLOAD
VIH
VCC(1)=3.3V±0.3V
VCC(2)=2.5V±0.2V
Unit
V
tPHL
tPHL
6
2 x Vcc
Vcc
tPLH
tPLH
VOH
VT
VOL
OUTPUT
3
V
VT
1.5
300
300
50
Vcc / 2
150
V
VLZ
mV
mV
pF
VIH
VT
0V
OPPOSITE PHASE
INPUT TRANSITION
VHZ
150
CL
30
Propagation Delay
DISABLE
VLOAD
Open
GND
VCC
ENABLE
VIH
VT
CONTROL
INPUT
500Ω
0V
tPZL
tPLZ
VIN
VOUT
(1, 2)
Pulse
VLOAD/2
VT
D.U.T.
VLOAD/2
VOL + VLZ
VOL
OUTPUT
NORMALLY
LOW
Generator
SWITCH
CLOSED
500Ω
tPHZ
RT
tPZH
CL
VOH
VOH -VHZ
OUTPUT
NORMALLY
HIGH
SWITCH
OPEN
VT
0V
0V
Test Circuits for All Outputs
NOTE:
1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH.
DEFINITIONS:
CL = Load capacitance: includes jig and probe capacitance.
RT = Termination resistance: should be equal to ZOUT of the Pulse Generator.
Enable and Disable Times
NOTES:
1. Pulse Generator for All Pulses: Rate ≤ 10MHz; tF ≤ 2.5ns; tR ≤ 2.5ns.
2. Pulse Generator for All Pulses: Rate ≤ 10MHz; tF ≤ 2ns; tR ≤ 2ns.
SWITCHPOSITION
Test
tPLZ/tPZL
tPHZ/tPZH
tPD
Switch
VLOAD
GND
Open
4
IDT74CBTLVR3862
INDUSTRIALTEMPERATURERANGE
LOW-VOLTAGE10-BITBUSSWITCHWITHACTIVEHIGHANDLOWENABLES
ORDERINGINFORMATION
CBTLV
X
IDT
XX
XXX
XX
Temp. Range
Family
Device Type Package
PY
Q
PG
Shrink Small Outline Package
Quarter-size Small Outline Package
Thin Shrink Small Outline Package
3862 Low-Voltage 10-Bit Bus Switch
R
25Ω series dampening resistors on A and B ports
74
–40°C to +85°C
CORPORATE HEADQUARTERS
2975StenderWay
Santa Clara, CA 95054
for SALES:
800-345-7015 or 408-727-6116
fax: 408-492-8674
for Tech Support:
logichelp@idt.com
(408) 654-6459
www.idt.com
5
相关型号:
IDT74CBTLVR3862Q8
Bus Driver, CBTLV/3B Series, 1-Func, 10-Bit, True Output, CMOS, PDSO24, QSOP-24
IDT
IDT74FBT2240AD
Bus Driver, BCT/FBT Series, 2-Func, 4-Bit, Inverted Output, BICMOS, CDIP20, 0.300 INCH, CERDIP-20
IDT
IDT74FBT2240AL
Bus Driver, BCT/FBT Series, 2-Func, 4-Bit, Inverted Output, BICMOS, CQCC20, LCC-20
IDT
IDT74FBT2240AP
Bus Driver, BCT/FBT Series, 2-Func, 4-Bit, Inverted Output, BICMOS, PDIP20, 0.300 INCH, PLASTIC, DIP-20
IDT
IDT74FBT2240ASO
Bus Driver, BCT/FBT Series, 2-Func, 4-Bit, Inverted Output, BICMOS, PDSO20, 0.300 INCH, SOIC-20
IDT
©2020 ICPDF网 联系我们和版权申明